Supero X10SLH-F User Manual

X10SLH-F

USER’S MANUAL

Revision 1.0a

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu­mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruc­tions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interfer­ence to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment to an outlet on a circuit different from that to which the receiver

is connected.

•Consult the authorized dealer or an experienced radio/TV technician for help.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn­ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to the
State of California to cause birth defects and other repro­ductive harm.

Manual Revision 1.0a
Release Date: April 4, 2014

Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2014 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

iii

Preface

Preface

This manual is written for system integrators, PC technicians and

knowledgeable PC users. It provides information for the installation and use of the

X10SLH-F motherboard.

About This Motherboard

The X10SLH-F supports a single Intel® Xeon E3-1200 v3 and 4th Genera-

tion Core™ i3, Pentium, Celeron processors in an LGA 1150 H3 socket. With the

Intel® C226 Express chipset built in, the X10SLH-F motherboard supports Intel®

Rapid Storage Technology, offering great system enhancement to Denlow Server

platforms. Please refer to our website (http://www.supermicro.com/products/) for

processor and memory support updates. This product is intended to be installed

and serviced by professional technicians.

Manual Organization

Chapter 1 describes the features, specications and performance of the mother-

board, and provides detailed information on the Intel® C226 Express chipset.

Chapter 2 provides hardware installation instructions. Read this chapter when in-

stalling the processor, memory modules and other hardware components into the

system. If you encounter any problems, see Chapter 3, which describes trouble-

shooting procedures for video, memory and system setup stored in the CMOS.

Chapter 4 includes an introduction to the BIOS, and provides detailed information

on running the CMOS Setup utility.

Appendix A provides BIOS Error Beep Codes.

Appendix B lists software program installation instructions.

Appendix C contains UEFI BIOS Recovery instructions.

Appendix D provides Dual BIOS Boot Block information for BIOS crisis recovery.

iv

Conventions Used in the Manual:

Special attention should be given to the following symbols for proper installation and

to prevent damage done to the components or injury to yourself:

Warning: Critical information to prevent damage to the components or injury to your-

self.

Important: Important information given to ensure proper system installa-

tion or to relay safety precautions.

Note: Additional Information given to differentiate various models or pro-

vides information for correct system setup.

X10SLH-F User’s Manual

v

Contacting Supermicro

Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Web Site: www.supermicro.com

Asia-Pacic

Address: Super Micro Computer, Inc.

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 235

Taiwan (R.O.C)

Tel: [phone]

Fax: [phone]

Email: [e-mail]

Tel: [phone]

Web Site: www.supermicro.com.tw

vi

Table of Contents

Preface

Chapter 1 Introduction

1-1 Overview ......................................................................................................... 1-1

1-2 Chipset Overview ......................................................................................... 1-10

1-3 Special Features ............................................................................................1-11

1-4 PC Health Monitoring .....................................................................................1-11

1-5 ACPI Features ............................................................................................... 1-12

1-6 Power Supply ................................................................................................ 1-12

1-7 Super I/O ....................................................................................................... 1-13

1-8 Advanced Power Management ..................................................................... 1-13

Intel® Intelligent Power Node Manager (NM) (Available when the NMView

utility is installed in the system) .................................................................... 1-13

Manageability Engine (ME) ........................................................................... 1-14

Chapter 2 Installation

2-1 Standardized Warning Statements ................................................................. 2-1

Battery Handling .............................................................................................. 2-1

Product Disposal ............................................................................................. 2-3

2-2 Static-Sensitive Devices .................................................................................. 2-4

Precautions ..................................................................................................... 2-4

Unpacking ....................................................................................................... 2-4

2-3 Processor and Heatsink Installation................................................................ 2-5

Installing the LGA1150 Processor ................................................................. 2-5

Installing an Active CPU Heatsink with Fan ................................................... 2-8

Removing the Heatsink ................................................................................. 2-10

2-4 Installing DDR3 Memory ................................................................................2-11

DIMM Installation ...........................................................................................2-11

Removing Memory Modules ......................................................................... 2-12

Memory Support ............................................................................................ 2-12

Memory Population Guidelines ..................................................................... 2-12

2-5 Motherboard Installation ................................................................................ 2-14

Tools Needed ................................................................................................ 2-14

Location of Mounting Holes .......................................................................... 2-14

Installing the Motherboard ............................................................................ 2-15

2-6 Connectors/IO Ports ...................................................................................... 2-16

Backplane I/O Panel ..................................................................................... 2-16

Serial Ports ............................................................................................... 2-17

Video Connection ..................................................................................... 2-17

X10SLH-F User’s Manual

vii

Table of Contents

Universal Serial Bus (USB) ...................................................................... 2-18

Ethernet Ports .......................................................................................... 2-19

Unit Identier Switch/UID LED Indicators ................................................ 2-20

Front Control Panel ....................................................................................... 2-21

Front Control Panel Pin Denitions............................................................... 2-22

NMI Button ............................................................................................... 2-22

Power LED .............................................................................................. 2-22

HDD LED .................................................................................................. 2-23

NIC1/NIC2 LEDs ...................................................................................... 2-23

Overheat (OH)/Fan Fail/PWR Fail/UID LED ............................................ 2-24

Power Fail LED ........................................................................................ 2-24

Reset Button ........................................................................................... 2-25

Power Button ........................................................................................... 2-25

2-7 Connecting Cables ........................................................................................ 2-26

ATX Main PWR & CPU PWR Connectors (JPW1 & JPW2) ................... 2-26

Fan Headers (Fan 1- Fan 4/Fan A) ......................................................... 2-27

Chassis Intrusion (JL1) ........................................................................... 2-27

Internal Buzzer (SPKR1) .......................................................................... 2-28

Onboard Power LED (JLED1) .................................................................. 2-28

DOM PWR Connector (JSD1) .................................................................. 2-29

Standby Power Header ............................................................................ 2-29

T-SGPIO 1/2 Headers .............................................................................. 2-30

TPM Header/Port 80 Header ................................................................... 2-30

Power SMB (I2C) Connector .................................................................... 2-31

2-8 Jumper Settings ............................................................................................ 2-32

Explanation of Jumpers ................................................................................ 2-32

GLAN Enable/Disable .............................................................................. 2-32

CMOS Clear (JBT1) ................................................................................. 2-33

PCI Slot SMB Enable (I2C1/I2C2) ............................................................. 2-33

Watch Dog Enable/Disable ...................................................................... 2-34

Backplane USB 4/5_Wake_Up Enable .................................................... 2-34

Manufacturer Mode Select ....................................................................... 2-35

ME Recovery ........................................................................................... 2-35

VGA Enable .............................................................................................. 2-36

2-9 Onboard Indicators ........................................................................................ 2-37

LAN1/LAN2 LEDs ..................................................................................... 2-37

IPMI_Dedicated LAN LEDs ...................................................................... 2-37

Onboard Power LED (LE3) ..................................................................... 2-38

BMC Heartbeat LED ................................................................................ 2-38

viii

2-10 SATA Connections ......................................................................................... 2-39

SATA 3.0 Connections .............................................................................. 2-39

Chapter 3 Troubleshooting

3-1 Troubleshooting Procedures ........................................................................... 3-1

3-2 Technical Support Procedures ........................................................................ 3-3

3-3 Frequently Asked Questions ........................................................................... 3-4

3-4 Battery Removal and Installation .................................................................... 3-5

3-5 Returning Merchandise for Service................................................................. 3-6

Chapter 4 BIOS

4-1 Introduction ...................................................................................................... 4-1

4-2 Main Setup ...................................................................................................... 4-2

4-3 Advanced Setup Congurations...................................................................... 4-4

4-4 Event Logs .................................................................................................... 4-22

4-5 Boot Settings ................................................................................................. 4-26

4-6 Security Settings ........................................................................................... 4-28

4-7 Save & Exit ................................................................................................... 4-29

Appendix A BIOS Error Beep Codes

A-1 BIOS Error Beep Codes .................................................................................A-1

Appendix B Software Installation Instructions

B-1 Installing Software Programs ..........................................................................B-1

B-2 Conguring SuperDoctor® III .......................................................................... B-2

Appendix C UEFI BIOS Recovery Instructions

C-1 An Overview to the UEFI BIOS ......................................................................C-1

C-2 How to Recover the UEFI BIOS Image (-the Main BIOS Block)....................C-1

C-3 To Recover the Main BIOS Block Using a USB-Attached Device..................C-1

Appendix D Dual Boot Block

D-1 Introduction ......................................................................................................D-1

D-2 Steps to Reboot the System by Using Jumper JBR1 (Available when JBR1 is

Installed onboard) .......................................................................................................D-2

X10SLH-F User’s Manual

Chapter 1: Introduction

1-1

Chapter 1

Introduction

1-1 Overview

Checklist

Congratulations on purchasing your computer motherboard from an acknowledged

leader in the industry. Supermicro boards are designed with the utmost attention to

detail to provide you with the highest standards in quality and performance.

Please check that the following items have all been included with your motherboard.

If anything listed here is damaged or missing, contact your retailer.

The following items are included in the retail box.

•One (1) Supermicro Motherboard

•Six (6) SATA cables

•One (1) I/O shield

•One (1) Quick Reference Guide

Note: For your system to work properly, please follow the links below to

download all necessary drivers/utilities and the user's manual for your

motherboard.

SMCI product manuals: http://www.supermicro.com/support/manuals/

Product Drivers and utilities: ftp://ftp.supermicro.com/

If you have any questions, please contact our support team at support@supermicro.

com.

1-2

X10SLH-F User’s Manual

X10SLH-F Motherboard Image

Note: All graphics shown in this manual were based upon the latest PCB Revision

available at the time of publishing of the manual. The motherboard you've received

may or may not look exactly the same as the graphics shown in this manual.

Chapter 1: Introduction

1-3

X10SLH-F Motherboard Layout

Important Notes to the User

•See Chapter 2 for detailed information on jumpers, I/O ports and JF1 front

panel connections.

•" " indicates the location of "Pin 1".

•Jumpers/components not indicated are for testing only.

•When LE3 (Onboard Power LED Indicator) is on, system power is on. Unplug

the power cable before installing or removing any components.

IPMI CODE

BIOS

LICENSE

BAR CODE

MAC CODE

FAN2

FAN3

FAN4

FAN1

FANA

JLED1

JWD1

JPG1

JPME1

JPME2

JPL2

JPL1

JPUSB1

J19

J18

LE3

LE5

LE4

JPW1

JPW2

JI2C1

JI2C2

JL1

J3

J4

JPI2C1

T-SGPIO1

T-SGPIO2

JSD1

JSTBY1

SPKR1

JBT1

JF1

J14

SW1

COM2

USB1 (3.0)

USB8/9

USB12/13

_LAN

IPMI

VGA

COM1

LAN1

DIMMB2

DIMMA2

USB4/5

CPU SLOT6 PCI-E 3.0 X8 (in X16)

CPU

Rev. 1.01

X10SLH-F

USB2/3(3.0)

I-SATA3
I-SATA4

I-SATA2

I-SATA1

I-SATA0

I-SATA5

CPU SLOT5 PCI-E 3.0 X8

PCH SLOT4 PCI-E 2.0 X2/4(INX8)

DIMMB1

DIMMA1

LAN2

PCH

LAN CTRL

LAN CTRL

Battery

TPM/Port 80

BMC

Vertical

USB0 (3.0)

1-4

X10SLH-F User’s Manual

IPMI CODE

BIOS

LICENSE

BAR CODE

MAC CODE

FAN2

FAN3

FAN4

FAN1

FANA

JLED1

JWD1

JPG1

JPME1

JPME2

JPL2

JPL1

JPUSB1

J19

J18

LE3

LE5

LE4

JPW1

JPW2

JI2C1

JI2C2

JL1

J3

J4

JPI2C1

T-SGPIO1

T-SGPIO2

JSD1

JSTBY1

SPKR1

JBT1

JF1

J14

SW1

COM2

USB1 (3.0)

USB8/9

USB12/13

_LAN

IPMI

VGA

COM1

LAN1

DIMMB2

DIMMA2

USB4/5

CPU SLOT6 PCI-E 3.0 X8 (in X16)

CPU

Rev. 1.01

X10SLH-F

USB2/3(3.0)

I-SATA3
I-SATA4

I-SATA2

I-SATA1

I-SATA0

I-SATA5

CPU SLOT5 PCI-E 3.0 X8

PCH SLOT4 PCI-E 2.0 X2/4(INX8)

DIMMB1

DIMMA1

LAN2

PCH

LAN CTRL

LAN CTRL

Battery

TPM/Port 80

BMC

Vertical

USB0 (3.0)

X10SLH-F Quick Reference

Chapter 1: Introduction

1-5

X10SLH-F Jumpers

Jumper Description Default

JBT1 CMOS Clear (See Chpt. 2)

JI2C1/JI2C2 SMB to PCI Slots Off (Disabled)

JPG1 VGA Enable Pins 1-2 (Enabled)

JPL1/JPL2 LAN1/LAN2 Enable Pins 1-2 (Enabled)

JPME1 ME Recovery Pins 2-3 (Normal)

JPME2 Manufacturing Mode Pins 2-3 (Normal)

JPUSB1 USB4/5 Wake_Up Enable Pins 2-3 (Disabled)

JWD1 Watch Dog Enable Pins 1-2 (RST)

X10SLH-F Headers/Connectors

Connector Description

Battery Onboard Battery

COM1/COM2 COM1/COM2 Port Headers

Fan1-Fan4, FanA System/CPU Fan Headers

J14 (See USB 1 ((3.0)) Vertical USB 1 (3.0) Connector

JF1 Front Panel Control Header

JL1 Chassis Intrusion Header

JLED1 Power LED Indicator Header

JPI2C1 Power System Management Bus (Power SMB)

JPW1 24-pin ATX Main Power Connector (Required)

JPW2 +12V 8-pin CPU power Connector (Required)

JSD1 SATA DOM (Device_On_Module) Power Connector

JSTBY1 Standby Power Header

JTPM1 Trusted Platform Module/Port 80 Connector

LAN1/LAN2 Gigabit (RJ45) Ports (LAN1/2)

SPKR1 Internal Speaker/Buzzer

I-SATA0-5 (SATA 3.0) (Intel PCH) Serial ATA (SATA 3.0) Ports 0-5 (6Gb/sec)

(CPU) Slot 6 PCI-Express 3.0 x8 in x16 Slot

(CPU) Slot 5 PCI-Express 3.0 x8 Slot

(PCH) Slot 4 PCI-Express 2.0 x4 in x8 Slot

SW1 Unit Identier (UID) Switch

T-SGPIO 1/2 Serial_Link General Purpose I/O Connection Headers 1/2

USB 0 (3.0)/USB 1 (3.0) USB 3.0 Port 0/USB 3.0 Vertical Header 1

USB 2/3 Backpanel USB Ports 2/3

USB 4/5 Backpanel USB 2.0 Ports 4/5

1-6

X10SLH-F User’s Manual

USB 8/9, USB 12/13 Front Panel Accessible USB 2.0 Headers 8/9, 12/13

VGA Backpanel VGA Port

X10SLH-F LED Indicators

LED Description Color/State Status

LE3 Onboard Standby PWR LED Green: Solid on Power On

LE4 Unit Identifer (UID) LED Blue: On Unit Identied

LE5 BMC Heartbeat LED Green Blinking BMC Normal

Chapter 1: Introduction

1-7

Motherboard Features

CPU Single Intel® Xeon E3-1200 v3 and 4th Generation Core™

i3, Pentium, Celeron processors in an LGA 1150 H3 socket.

Memory Supports up to 32 GB of DDR3 Unbuffered ECC 1600/1333

MHz (1.35V/1.5V) memory in four memory slots.

Dual-channel memory

DIMM sizes

UDIMM 1 GB, 2 GB, 4GB, and 8GB

Chipset Intel® C226 Express

Expansion Slots •One (1) PCI Express 2.0 x4 in x8 slot

One (1) PCI Express 3.0 x8 slot (CPU Slot 5)

One (1) PCI Express 3.0 x8 in x16 slot (CPU Slot 6)

Network Connections Intel® i210 Gigabit Ethernet Controllers:

•Two (2) i210 LAN controllers for LAN1/LAN2;

•Two (2) RJ-45 rear I/O panel connectors with Link

and Activity LEDs

I/O Devices SATA Connections

SATA 3.0 (6Gb/s) Six (6) I-SATA 0-5 via Intel® C226

Express with Intel® Rapid Storage

Technology support

RAID 0, 1, 5, 10

USB Devices

Two (2) USB 3.0 ports on the rear I/O panel (USB 2/3),
Two (2) USB 2.0 ports on the rear I/O panel (USB 4/5)

Four (4) Front Accessible USB 2.0 ports on two headers
(USB 8/9, USB 12/13),
One (1) Front Accessible Type A USB 3.0 (USB 0),
One (1) Front Accessible Vertical Type A USB 3.0 (USB 1)

Serial (COM) Ports

Two (2) front accessible Serial Port headers (COM1/
COM2)

Super I/O

Nuvoton NCT6776

BIOS 64 Mb AMI BIOS® SPI Flash BIOS

Play and Plug (PnP0, DMI 2.3, PCI 2.3, ACPI 1.0/2.0/3.0,
USB Keyboard and SMBIOS 2.5

Power Conguration ACPI/ACPM Power Management

1-8

X10SLH-F User’s Manual

Main Switch Override Mechanism

Keyboard Wake-up from Soft-Off

Internal/External Modem Ring-On

Power-on mode for AC power recovery

PC Health Monitoring CPU Monitoring

Onboard voltage monitors for CPU core, +3.3V, +5V,-12V,
+12V, +3.3V Stdby, VBAT, Memory, VCORE for CPU

CPU 3-phase switching voltage regulator

CPU/System overheat LED and control

CPU Thermal Trip support

Thermal Monitor 2 (TM2) support

Fan Control

Fan status monitoring with rmware 4-pin fan speed con­trol via IPMI interface

Low noise fan speed control

System Management PECI (Platform Environment Conguration Interface) 3.0

support

System resource alert via SuperDoctor® III

SuperDoctor® III, Watch Dog, NMI

Chassis Intrusion header and detection

CD Utilities BIOS ash upgrade utility

Other ROHS 6/6 (Full Compliance, Lead Free)

Dimensions ATX form factor (9.6" x 9.6") (243.84 mm x 243.84 mm)

Chapter 1: Introduction

1-9

System Block Diagram

Note: This is a general block diagram and may not exactly represent

the features on your motherboard. See the Motherboard Features

pages for the actual specications of each motherboard.

X10SLH-F Block Diagram

Lynx Point

DDR3 (CHA)

Haswell

(H3)

PCIe3.0_x16

SVID

LPC I/O

NCT6776D

PCIe x16 SLOT

RJ45

RJ45

DDR3 (CHB)

DIMM1

DIMM2(Far)

1600/1333MHz

8.0Gb

x4 DMI II

5.0Gb

5.0Gbps

PCIe_x4

PCIe x8 SLOT

4 USB PORTS

USB3.0

FLASH

SPI 128Mb

SPI

PCIe_x1

2.5Gbps

GLAN1
I210

COM1, 2

LPC

HEALTH
INFO

LPC

TPM1.2 Header

LPC

PCIe_x1

2.5Gbps

GLAN2
I210

RGMII

VGA

PORT

RTL8211E
PHY

ASPEED

ASP2400

PCIe x1

RJ45

PCIe x8 SLOT

SATA-III

6 SATA PORTS

PCH

C226

1600/1333MHz

480Mbps

USB2.0

6 USB PORTS

6.0Gbps

5.0Gbps

DIMM1
DIMM2(Far)

VRM 12.5
MISC VRs

1-10

X10SLH-F User’s Manual

1-2 Chipset Overview

The X10SLH-F supports a single Intel® Xeon E3-1200 v3 and 4th Generation

Core™ i3, Pentium, Celeron processors in an LGA 1150 H3 socket. Built upon the

functionality and the capability of the C226 Express chipset, the motherboard

provides substantial enhancement to system performance and storage capability

for high performance platforms in a sleek package.

The high-speed Direct Media Interface (DMI) featured in the Intel® C226 Express

chipset supports high-speed Direct Media Interface (DMI) for chip-to-chip true iso-

chronous communication, providing up to 10 Gb/s of software-transparent data

transfer rate on each read/write direction. In addition, the X10SLH-F also features

a TCO timer which allows the system to recover from a software/hardware lock

and perform tasks, including Function Disable and Intruder Detect.

Intel C226 Express Chipset Features

•Direct Media Interface (up 10 Gb/s transfer, Full Duplex)

•Intel

®

Matrix Storage Technology and Intel Rapid® Storage Technology

•Dual NAND Interface

•Intel

®

I/O Virtualization (VT-d) Support

•Intel

®

Rapid Storage Technology Support

•Intel

®

Trusted Execution Technology Support

•PCI Express 2.0 Interface (up to 5.0 GT/s)

•SATA Controller (up to 6Gb/sec)

•Advanced Host Controller Interface (AHCI)

•Intel

®

Active Management Technology (iAMT) 9.0 and vPRO 9.0 support

Chapter 1: Introduction

1-11

1-3 Special Features

Recovery from AC Power Loss

Basic I/O System (BIOS) provides a setting for you to determine how the system will

respond when AC power is lost and then restored to the system. You can choose

for the system to remain powered off, (in which case you must press the power

switch to turn it back on), or for it to automatically return to a power-on state. See

the Advanced BIOS Setup section to change this setting. The default setting is

Last State.

1-4 PC Health Monitoring

This section describes the PC health monitoring features of the board. All have an

onboard System Hardware Monitoring chip that supports PC health monitoring. An

onboard voltage monitor will scan these onboard voltages continuously: CPU Vcore,

12V, -12V, 5V, 3.3V, 3.3VSB, memory and battery voltages. Once a voltage becomes

unstable, a warning is given, or an error message is sent to the screen. The user

can adjust the voltage thresholds to dene the sensitivity of the voltage monitor.

Fan Status Monitor with Firmware Control

PC health monitoring in the BIOS can check the RPM status of the cooling fans.

The onboard CPU and chassis fans are controlled by Thermal Management via

IPMI Firmware.

Environmental Temperature Control

The thermal control sensor monitors the CPU temperature in real time and will turn

on the thermal control fan whenever the CPU temperature exceeds a user-dened

threshold. The overheat circuitry runs independently from the CPU. Once the ther-

mal sensor detects that the CPU temperature is too high, it will automatically turn

on the thermal fans to prevent the CPU from overheating. The onboard chassis

thermal circuitry can monitor the overall system temperature and alert the user when

the chassis temperature is too high.

Note: To avoid possible system overheating, please be sure to provide

adequate airow to your system.

1-12

X10SLH-F User’s Manual

System Resource Alert

This feature is available when the system is used with SuperDoctor® III in the

Windows OS environment or used with SuperDoctor II in Linux. SuperDoctor

is used to notify the user of certain system events. For example, you can also

congure SuperDoctor to provide you with warnings when the system temperature,

CPU temperatures, voltages and fan speeds go beyond predened thresholds.

1-5 ACPI Features

ACPI stands for Advanced Conguration and Power Interface. The ACPI specica-

tion denes a exible and abstract hardware interface that provides a standard

way to integrate power management features throughout a PC system, including

its hardware, operating system and application software. This enables the system

to automatically turn on and off peripherals such as CD-ROMs, network cards, hard

disk drives and printers.

In addition to enabling operating system-directed power management, ACPI also

provides a generic system event mechanism for Plug and Play, and an operating

system-independent interface for conguration control. ACPI leverages the Plug and

Play BIOS data structures, while providing a processor architecture-independent

implementation that is compatible with Windows 7, Windows 8, and Windows 2008

Operating Systems.

Slow Blinking LED for Suspend-State Indicator

When the CPU goes into a suspend state, the chassis power LED will start to blink

to indicate that the CPU is in suspend mode. When the user presses any key, the

CPU will "wake up", and the LED will automatically stop blinking and remain on.

1-6 Power Supply

As with all computer products, a stable power source is necessary for proper and

reliable operation. It is even more important for processors that have high CPU

clock rates.

This motherboard accommodates 24-pin ATX power supplies. Although most

power supplies generally meet the specications required by the CPU, some are

inadequate. In addition, the 12V 8-pin power connector located at JPW2 is also

required to ensure adequate power supply to the system. Also your power supply

must supply 1.5A for the Ethernet ports.

Warning: 1. To prevent damage to the power supply or motherboard, please use a

power supply that contains a 24-pin and a 8-pin power connectors. Be sure to connect

these connectors to the 24-pin (JPW1) and the 8-pin (JPW2) power connectors on the

Chapter 1: Introduction

1-13

motherboard. Failure in doing so will void the manufacturer warranty on your power

supply and motherboard. 2. To provide adequate power to SATA devices, please con-

nect the SATA DOM PWR connector (JSD1) to the power supply.

It is strongly recommended that you use a high quality power supply that meets ATX

power supply Specication 2.02 or above. It must also be SSI compliant. (For more

information, please refer to the web site at http://www.ssiforum.org/). Additionally, in

areas where noisy power transmission is present, you may choose to install a line

lter to shield the computer from noise. It is recommended that you also install a

power surge protector to help avoid problems caused by power surges.

1-7 Super I/O

The Super I/O supports two high-speed, 16550 compatible serial communication

ports (UARTs). Each UART includes a 16-byte send/receive FIFO, a programmable

baud rate generator, complete modem control capability and a processor interrupt

system. Both UARTs provide legacy speed with baud rate of up to 115.2 Kbps

as well as an advanced speed with baud rates of 250 K, 500 K, or 1 Mb/s, which

support higher speed modems.

The Super I/O provides functions that comply with ACPI (Advanced Conguration

and Power Interface), which includes support of legacy and ACPI power manage-

ment through an SMI or SCI function pin. It also features auto power management

to reduce power consumption.

1-8 Advanced Power Management

The following advanced power management features are supported by this moth-

erboard:

Intel® Intelligent Power Node Manager (NM) (Available
when the NMView utility is installed in the system)

The Intel® Intelligent Power Node Manager (IPNM) provides your system with

real-time thermal control and power management for maximum energy efciency.

Although IPNM Specication Version 1.5/2.0 is supported by the BMC (Baseboard

Management Controller), your system must also have IPNM-compatible Manage-

ability Engine (ME) rmware installed to use this feature.

Note: Support for IPNM Specication Version 1.5 or Version 2.0 depends

on the power supply used in the system.

1-14

X10SLH-F User’s Manual

Manageability Engine (ME)

The Manageability Engine, which is an ARC controller embedded in the PCH,

provides Server Platform Services (SPS) to your system. The services provided by

SPS are different from those provided by the ME on client platforms.

Chapter 2: Installation

2-1

Chapter 2

Installation

2-1 Standardized Warning Statements

The following statements are industry-standard warnings, provided to warn the user

of situations which have the potential for bodily injury. Should you have questions or

experience difculty, contact Supermicro's Technical Support department for assis-

tance. Only certied technicians should attempt to install or congure components.

Read this section in its entirety before installing or conguring components in the

Supermicro chassis.

Battery Handling

Warnung

Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die

Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.

Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.

Warning!

There is a danger of explosion if the battery is replaced incorrectly. Replace the

battery only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's instructions

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。 交換する電池はメー
カーが推奨する型、または同等のものを使用下さい。 使用済電池は製造元の指示に従
って処分して下さい。

警告

电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更

换原有电池。请按制造商的说明处理废旧电池。

警告

電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有

電池。請按照製造商的說明指示處理廢棄舊電池。

2-2

X10SLH-F User’s Manual

Attention

Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer

que par une pile de type semblable ou équivalent, recommandée par le fabricant.

Jeter les piles usagées conformément aux instructions du fabricant.

¡Advertencia!

Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Re-

emplazar la batería exclusivamente con el mismo tipo o el equivalente recomen-

dado por el fabricante. Desechar las baterías gastadas según las instrucciones

del fabricante.

!הרהזא

תנכס תמייקץוציפ .הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי

גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ.

תוללוסה קוליס תושמושמה עצבל שי .ןרציה תוארוה יפל









경고!

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일
하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다. 제조사
의 안내에 따라 사용된 배터리를 처리하여 주십시오.

Waarschuwing

Er is ontplofngsgevaar indien de batterij verkeerd vervangen wordt. Vervang de

batterij slechts met hetzelfde of een equivalent type die door de fabrikant aan-

bevolen wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften

afgevoerd te worden.

Chapter 2: Installation

2-3

Product Disposal

Warning!

Ultimate disposal of this product should be handled according to all national laws

and regulations.

製品の廃棄

この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が

ありま す。

警告
本产品的废弃处理应根据所有国家的法律和规章进行。

警告
本產品的廢棄處理應根據所有國家的法律和規章進行。

Warnung

Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen

des Landes erfolgen.

¡Advertencia!

Al deshacerse por completo de este producto debe seguir todas las leyes y regla-

mentos nacionales.

Attention

La mise au rebut ou le recyclage de ce produit sont généralement soumis à des

lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de

l'organisme compétent.

רצומה קוליס

!הרהזא

ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס.הנידמה יקוח

2-4

X10SLH-F User’s Manual

2-2 Static-Sensitive Devices

Electrostatic-Discharge (ESD) can damage electronic com ponents. To avoid dam-

aging your system board, it is important to handle it very carefully. The following

measures are generally sufcient to protect your equipment from ESD.

Precautions

• Use a grounded wrist strap designed to prevent static discharge.

• Touch a grounded metal object before removing the board from the antistatic

bag.

• Handle the board by its edges only; do not touch its components, peripheral

chips, memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the motherboard and peripherals back into their antistatic bags when not in

use.

• For grounding purposes, make sure your computer chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and

the motherboard.

• Use only the correct type of onboard CMOS battery. Do not install the onboard

battery upside down to avoid possible explosion.

Unpacking

The motherboard is shipped in antistatic packaging to avoid static damage. When

unpacking the board, make sure that the person handling it is static protected.

Waarschuwing

De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming

met alle nationale wetten en reglementen.

 

경고!

이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.

Chapter 2: Installation

2-5

2-3 Processor and Heatsink Installation

Warning: When handling the processor package, avoid placing direct pressure on the

label area of the fan.

Important:

•Always connect the power cord last, and always remove it before adding,

removing or changing any hardware components. Make sure that you install

the processor into the CPU socket before you install the CPU heatsink.

•If you buy a CPU separately, make sure that you use an Intel-certied multi-

directional heatsink only.

•Make sure to install the system board into the chassis before you install

the CPU heatsink.

•When receiving a server board without a processor pre-installed, make sure

that the plastic CPU socket cap is in place and none of the socket pins are

bent; otherwise, contact your retailer immediately.

•Refer to the Supermicro website for updates on CPU support.

Load Lever

Installing the LGA1150 Processor

1. Press the load lever to release the load plate, which covers the CPU socket,

from its locking position.

Load Plate

2-6

X10SLH-F User’s Manual

2. Gently lift the load lever to open the load plate. Remove the plastic cap.

3. Use your thumb and your index nger to hold the CPU at the North center

edge and the South center edge of the CPU.

4. Align the CPU key that is the semi-circle cutouts against the socket keys.

Once it is aligned, carefully lower the CPU straight down into the socket. (Do

not drop the CPU on the socket. Do not move the CPU horizontally or verti-

cally.

South Center Edge

North Center Edge

Chapter 2: Installation

2-7

Warning: You can only install the CPU inside the socket only in one direction. Make

sure that it is properly inserted into the CPU socket before closing the load plate. If it

doesn't close properly, do not force it as it may damage your CPU. Instead, open the

load plate again and double-check that the CPU is aligned properly.

CPU properly
installed

Load lever locked

into place

5. Do not rub the CPU against the surface or against any pins of the socket to

avoid damaging the CPU or the socket.)

6. With the CPU inside the socket, inspect the four corners of the CPU to make

sure that the CPU is properly installed.

7. Use your thumb to gently push the load lever down to the lever lock.

2-8

X10SLH-F User’s Manual

Thermal Grease

Heatsink
Fins

Recommended Supermicro

heatsink:

SNK-P0046A4 active heatsink

Installing an Active CPU
Heatsink with Fan

1. Locate the CPU Fan power connec-

tor on the motherboard. (Refer to

the layout on the right for the CPU

Fan location.)

2. Position the heatsink so that the

heatsink fan wires are closest to the

CPU fan power connector and are

not interfered with other compo-

nents.

3. Inspect the CPU Fan wires to make

sure that the wires are routed

through the bottom of the heatsink.

4. Remove the thin layer of the protec-

tive lm from the heatsink.

Warning: CPU overheat may occur if the

protective film is not removed from the

heatsink.

5. Apply the proper amount of thermal

grease on the CPU.

Note: If your heatsink came with

a thermal pad, please ignore

this step.

6. If necessary, rearrange the wires

to make sure that the wires are not

pinched between the heatsink and

the CPU. Also make sure to keep

clearance between the fan wires

and the ns of the heatsink.