Supero X10SAT User Manual

X10SAT

USER’S MANUAL

Revision 1.0

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu­mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruc­tions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interfer­ence to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment to an outlet on a circuit different from that to which the

receiver is connected.

•Consult the authorized dealer or an experienced radio/TV technician for help.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn­ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to the
State of California to cause birth defects and other repro­ductive harm.

Manual Revision 1.0
Release Date: September 3, 2013

Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2013 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

iii

Preface

Preface

This manual is written for system integrators, PC technicians and

knowledgeable PC users. It provides information for the installation and use of the

X10SAT motherboard.

About This Motherboard

The X10SAT supports a single 4th Generation Intel® Core™ i7/i5/i3 DT

processor, E3-1200 V3 series processor in an LGA 1150 (H3) socket. With the Intel®

C226 Express chipset built in, the X10SAT motherboard offers substantial system

performance and storage capability in a sleek package. Please refer to our website

(http://www.supermicro.com/products/) for processor and memory support updates.

This product is intended to be installed and serviced by professional technicians.

Manual Organization

Chapter 1 describes the features, specications and performance of the mother-

board, and provides detailed information on the Intel C226 Express chipset.

Chapter 2 provides hardware installation instructions. Read this chapter when in-

stalling the processor, memory modules and other hardware components into the

system. If you encounter any problems, see Chapter 3, which describes trouble-

shooting procedures for video, memory and system setup stored in the CMOS.

Chapter 4 includes an introduction to the BIOS, and provides detailed information

on running the CMOS Setup utility.

Appendix A provides BIOS Error Beep Codes.

Appendix B lists software program installation instructions.

Appendix C contains UEFI BIOS Recovery instructions.

Appendix D contains an introduction and instructions regarding the Dual Boot Block

feature of this motherboard.

iv

Conventions Used in the Manual:

Special attention should be given to the following symbols for proper installation and

to prevent damage done to the components or injury to yourself:

Warning: Critical information to prevent damage to the components or injury to your-

self.

Important: Important information given to ensure proper system installa-

tion or to relay safety precautions.

Note: Additional Information given to differentiate various models or pro-

vides information for correct system setup.

X10SAT User’s Manual

v

Contacting Supermicro

Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Asia-Pacic

Address: Super Micro Computer, Inc.

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 23511

Taiwan (R.O.C)

Tel: [phone]

Fax: [phone]

Web Site: www.supermicro.com.tw

Technical Support:

Email: [e-mail]

Tel: [phone]

vi

Table of Contents

Preface

About This Motherboard ................................................................................................ iii

Manual Organization .....................................................................................................iii

Conventions Used in the Manual: .................................................................................iv

Contacting Supermicro ...................................................................................................v

Chapter 1

Introduction

1-1 Overview ......................................................................................................... 1-1

Checklist .......................................................................................................... 1-1

Motherboard Features ..................................................................................... 1-6

1-2 Chipset Overview ........................................................................................... 1-9

Intel C226 Express Chipset Features ............................................................. 1-9

1-3 Special Features ........................................................................................... 1-10

Recovery from AC Power Loss ..................................................................... 1-10

1-4 PC Health Monitoring .................................................................................... 1-10

Fan Status Monitor with Firmware Control .................................................. 1-10

Environmental Temperature Control ............................................................. 1-10

System Resource Alert ................................................................................. 1-10

1-5 ACPI Features ................................................................................................1-11

Slow Blinking LED for Suspend-State Indicator ............................................1-11

1-6 Power Supply .................................................................................................1-11

1-7 Super I/O ....................................................................................................... 1-12

Chapter 2

Installation

2-1 Standardized Warning Statements ................................................................. 2-1

Battery Handling .............................................................................................. 2-1

Product Disposal ............................................................................................. 2-3

2-2 Static-Sensitive Devices .................................................................................. 2-4

Precautions ..................................................................................................... 2-4

Unpacking ....................................................................................................... 2-4

2-3 Processor and Heatsink Installation................................................................ 2-5

Installing the LGA1150 Processor ................................................................. 2-5

Installing an Active CPU Heatsink with Fan ................................................... 2-8

Removing the Heatsink ................................................................................. 2-10

2-4 Installing DDR3 Memory ................................................................................2-11

X10SAT User’s Manual

vii

Table of Contents

DIMM Installation ...........................................................................................2-11

Removing Memory Modules ..........................................................................2-11

Memory Support ............................................................................................ 2-12

Memory Population Guidelines ..................................................................... 2-12

Memory Population Guidelines ..................................................................... 2-13

2-5 Motherboard Installation ................................................................................ 2-14

Tools Needed ................................................................................................ 2-14

Location of Mounting Holes .......................................................................... 2-14

Installing the Motherboard ............................................................................ 2-15

2-6 Connectors/IO Ports ...................................................................................... 2-16

Backplane I/O Panel ..................................................................................... 2-16

Universal Serial Bus (USB) ...................................................................... 2-17

Ethernet Ports .......................................................................................... 2-18

Back Panel High Denition Audio (HD Audio) ........................................ 2-18

HDMI Port ................................................................................................. 2-19

VGA Port ..................................................................................................2-19

DVI Port .................................................................................................... 2-19

Thunderbolt Interface ............................................................................... 2-20

CMOS Reset/Clear ................................................................................... 2-20

Front Control Panel ....................................................................................... 2-21

Front Control Panel Pin Denitions............................................................... 2-22

Power LED .............................................................................................. 2-22

HDD LED .................................................................................................. 2-22

NIC1/NIC2 (LAN1/LAN2) .......................................................................... 2-22

Overheat (OH)/Fan Fail ............................................................................ 2-22

Reset Button ........................................................................................... 2-23

Power Button ........................................................................................... 2-23

2-7 Connecting Cables ........................................................................................ 2-24

ATX Main PWR & CPU PWR Connectors (JPW1 & JPW2) ................... 2-24

Fan Headers (Fan 1 ~ Fan 5) .................................................................. 2-25

Chassis Intrusion (JL1) ........................................................................... 2-25

Internal Buzzer (SP1) ............................................................................... 2-26

Speaker (JD1) .......................................................................................... 2-26

Onboard Power LED (JLED1) .................................................................. 2-27

Serial Port (COM1) ................................................................................... 2-27

DOM PWR Connector (JSD1) .................................................................. 2-28

SPDIF OUT (JSPDIF_OUT) ..................................................................... 2-28

Standby Power Header ............................................................................ 2-29

TPM Header/Port 80 Header ................................................................... 2-30

viii

IEEE 1394 Header ................................................................................... 2-30

Front Panel Audio Header (AUDIO FP) ................................................... 2-31

T-SGPIO 1/2 Headers .............................................................................. 2-31

2-8 Jumper Settings ............................................................................................ 2-32

Explanation of Jumpers ................................................................................ 2-32

LAN1/LAN2 Enable/Disable ..................................................................... 2-32

CMOS Clear (JBT1) ................................................................................. 2-33

PCI Slot SMB Enable (I2C1/I2C2) ............................................................. 2-33

Audio Enable (JPAC1).............................................................................. 2-34

Watch Dog Enable/Disable ...................................................................... 2-34

USB Wake-Up (JPUSB 1/2) ..................................................................... 2-35

Intel Recovery Mode (JPME1) ................................................................. 2-36

Intel Manufacturing Mode (JPME2).......................................................... 2-36

BIOS Recovery (JBR1) ............................................................................ 2-37

Power Button ............................................................................................ 2-37

2-9 Onboard Indicators ........................................................................................ 2-38

LAN 1/LAN 2 LEDs .................................................................................. 2-38

Onboard Power LED (LED1) .................................................................. 2-38

2-10 SATA Connections ......................................................................................... 2-39

SATA Connections (I-SATA0~I-SATA5) .................................................... 2-39

Chapter 3

Troubleshooting

3-1 Troubleshooting Procedures ........................................................................... 3-1

Before Power On ............................................................................................ 3-1

No Power ........................................................................................................ 3-1

No Video ......................................................................................................... 3-2

Memory Errors ............................................................................................... 3-2

Losing the System’s Setup Conguration ....................................................... 3-2

3-2 Technical Support Procedures ........................................................................ 3-3

3-3 Frequently Asked Questions ........................................................................... 3-4

3-4 Battery Removal and Installation .................................................................... 3-5

Battery Removal .............................................................................................. 3-5

Proper Battery Disposal .................................................................................. 3-5

3-5 Returning Merchandise for Service................................................................. 3-6

Battery Installation ........................................................................................... 3-6

X10SAT User’s Manual

ix

Chapter 4

BIOS

4-1 Introduction ...................................................................................................... 4-1

Starting BIOS Setup Utility .............................................................................. 4-1

How To Change the Conguration Data ......................................................... 4-1

How to Start the Setup Utility ......................................................................... 4-2

4-2 Main Setup ...................................................................................................... 4-2

The following Main menu items will be displayed: ..................................... 4-2

System Date/System Time ........................................................................ 4-3

Supermicro X10SAT ................................................................................... 4-3

Version ........................................................................................................4-3

Build Date ................................................................................................... 4-3

Memory Information ................................................................................... 4-3

Total Memory .............................................................................................. 4-3

4-3 Advanced Setup Congurations...................................................................... 4-4

Boot Feature ................................................................................................... 4-4

Quiet Boot .................................................................................................. 4-4

AddOn ROM Display Mode ........................................................................ 4-4

Bootup Num-Lock ....................................................................................... 4-4

Wait For 'F1' If Error ................................................................................... 4-5

Interrupt 19 Capture ................................................................................... 4-5

Re-try Boot ................................................................................................. 4-5

Power Conguration ........................................................................................ 4-5

Watch Dog Function ................................................................................... 4-5

Power Button Function ............................................................................... 4-5

Restore on AC Power Loss ........................................................................ 4-5



CPU Conguration ....................................................................................... 4-6

Clock Spread Spectrum ............................................................................ 4-7

Hyper-threading .......................................................................................... 4-7

Active Processor Cores .............................................................................. 4-7

Limit CPUID Maximum ............................................................................... 4-7

Execute Disable Bit .................................................................................... 4-7

Intel® Virtualization Technology ................................................................. 4-7

Hardware Prefetcher .................................................................................. 4-7

Adjacent Cache Line Prefetch ................................................................... 4-7

CPU AES .................................................................................................... 4-8

Boot Performance Mode ............................................................................ 4-8

EIST ............................................................................................................ 4-8

Table of Contents

x

Turbo Mode ................................................................................................ 4-8

Energy Performance ................................................................................ 4-10

VR Current Value ..................................................................................... 4-10

CPU C States ........................................................................................... 4-10

Package C-State limit ................................................................................4-11

LakeTiny Feature .......................................................................................4-11

ACPI T State .............................................................................................4-11



Chipset Conguration ................................................................................. 4-12



System Agent (SA) Conguration .............................................................. 4-12

VT-d .......................................................................................................... 4-12



Graphics Conguration ............................................................................... 4-12

Primary Display ........................................................................................ 4-12

CPU IGFX ................................................................................................ 4-13

GTT Size .................................................................................................. 4-13

Aperture Size ............................................................................................ 4-13

DVMT Pre-Allocated ................................................................................. 4-13

DVMT (Dynamic Video Memory Technology) Total Gfx Mem .................. 4-13

Gfx (Graphics) Low Power Mode ............................................................. 4-13



PCH-IO Conguration ................................................................................ 4-16

Legacy USB Support ................................................................................ 4-16

XHCI Hand-Off ......................................................................................... 4-17

EHCI Hand-Off ......................................................................................... 4-17

XHCI Mode ............................................................................................... 4-17

Frontside Audio Mode .............................................................................. 4-17



On Board Chip Conguration ..................................................................... 4-17

SATA Mode ............................................................................................... 4-17



SATA Conguration .................................................................................... 4-18

SATA Controllers ...................................................................................... 4-18

SATA Mode Selection ............................................................................... 4-18

SATA RAID Option ROM/UEFI Driver (Available if the item above - SATA

Mode Select is set to AHCI or RAID)....................................................... 4-18



PCIe/PCI/PnP Conguration ..................................................................... 4-19

Above 4G Decoding ................................................................................. 4-19

VGA Palette Snoop .................................................................................. 4-20

PCH SLOT1 PCI-E 2.0 X1 (IN X4) OPROM, CPU SLOT2 PCI-E 3.0 X4 (IN
X16) OPROM, PCH SLOT3 PCI-E 2.0 X1 (IN X4) OPROM,
CPU SLOT4 PCI-E 3.0 X8 (IN X16) OPROM, PCH SLOT5 PCI-E 2.0 X1

(IN X4) OPROM, CPU SLOT6 PCI-E 3.0 X16 OPROM .......................... 4-20

Launch Storage OPROM Policy............................................................... 4-20

Other PCI Device ROM Priority ............................................................... 4-20

X10SAT User’s Manual

xi

Onboard LAN1 Option ROM/Onboard LAN2 Option ROM ...................... 4-20

Network Stack .......................................................................................... 4-20

Ipv4 PXE Support ..................................................................................... 4-20

Ipv6 PXE Support ..................................................................................... 4-21



ACPI Settings ............................................................................................ 4-21

High Precision Timer ................................................................................ 4-21

ACPI Sleep State ..................................................................................... 4-21

WHEA Support ......................................................................................... 4-21



Trusted Computing ..................................................................................... 4-21

Conguration ............................................................................................ 4-21

Current Status Information ....................................................................... 4-22

Intel TXT (LT) Support .............................................................................. 4-22



PCH-FW Conguration ............................................................................... 4-22



Firmware Update Conguration ................................................................. 4-22

ME FW Image Re-Flash .......................................................................... 4-22

AMT (Active Management Technology) Conguration .............................. 4-23

Intel AMT .................................................................................................. 4-23

Activate Remote Assistance Process....................................................... 4-23

Watch Dog Timer ...................................................................................... 4-23



Super IO Conguration ............................................................................. 4-23

Super IO Chip NCT6776D ...................................................................... 4-23



Serial Port 1 Conguration .................................................................... 4-23

Device Settings ........................................................................................ 4-23

Change Port 1 Settings ............................................................................ 4-23



H/W (Hardware) Monitor ............................................................................ 4-24

PC Health Status ...................................................................................... 4-24

Fan Speed Control Mode ......................................................................... 4-24



Serial Port Console Redirection ................................................................. 4-26

4-4 Event Logs .................................................................................................... 4-28

Smbios Event Log .................................................................................... 4-28

PCI Error Logging Support ....................................................................... 4-28

Erase Event Log ....................................................................................... 4-28

When Log is Full ...................................................................................... 4-28

Log System Boot Event .......................................................................... 4-28

MECI ......................................................................................................... 4-28

METW ....................................................................................................... 4-29



View SMBIOS Event Log ...................................................................... 4-29

4-5 Boot Settings ................................................................................................. 4-29

Set Boot Priority ....................................................................................... 4-29

Table of Contents

xii



Hard Disk Drive BBS Priorities ............................................................. 4-30



UEFI Boot Drive BBS Priorities............................................................. 4-30



Add New Boot Option ........................................................................... 4-30



Delete Boot Option ................................................................................ 4-30



Delete Driver Option ............................................................................. 4-30

4-6 Security Settings ........................................................................................... 4-31

Administrator Password ........................................................................... 4-31

HDD Security Conguration ..................................................................... 4-31

4-7 Save & Exit ................................................................................................... 4-32

Discard Changes and Exit ...................................................................... 4-32

Save Changes and Reset ........................................................................ 4-32

Save Options ............................................................................................ 4-32

Save Changes .......................................................................................... 4-32

Discard Changes ...................................................................................... 4-32

Restore Optimized Defaults ..................................................................... 4-32

Save As User Defaults ............................................................................. 4-33

Restore User Defaults .............................................................................. 4-33

Boot Override ........................................................................................... 4-33

Appendix A

BIOS Error Beep Codes

A-1 BIOS Error Beep Codes .................................................................................A-1

Appendix B

Software Installation Instructions

B-1 Installing Drivers ..............................................................................................B-1

B-2 Conguring SuperDoctor® III .......................................................................... B-2

Appendix C

UEFI BIOS Recovery Instructions

C-1 An Overview to the UEFI BIOS ......................................................................C-1

C-2 How to Recover the UEFI BIOS Image (the Main BIOS Block) .....................C-1

C-3 To Recover the Main BIOS Block Using a USB-Attached Device..................C-1

Appendix D

Dual Boot Block

D-1 Introduction ......................................................................................................D-1

BIOS Boot Block .............................................................................................D-1

BIOS Boot Block Corruption Occurrence ......................................................D-1

D-2 Steps to Reboot the System by Using Jumper JBR1 ....................................D-2

X10SAT User’s Manual

Chapter 1: Introduction

1-1

Chapter 1

Introduction

1-1 Overview

Checklist

Congratulations on purchasing your computer motherboard from an acknowledged

leader in the industry. Supermicro boards are designed with the utmost attention to

detail to provide you with the highest standards in quality and performance.

Please check that the following items have all been included with your motherboard.

If anything listed here is damaged or missing, contact your retailer.

The following items are included in the retail box.

•One (1) Supermicro Motherboard

•Two (2) SATA cables

•One (1) I/O shield

•One (1) Quick Reference Guide

Note: For your system to work properly, please follow the links below to

download all necessary drivers/utilities and the user's manual for your

motherboard.

SMCI product manuals: http://www.supermicro.com/support/manuals/

Product Drivers and utilities: ftp://ftp.supermicro.com/

If you have any questions, please contact our support team at support@supermicro.

com.

1-2

X10SAT User’s Manual

X10SAT Motherboard Image

Note: All graphics shown in this manual were based upon the latest PCB Revision

available at the time of publishing of the manual. The motherboard you've received

may or may not look exactly the same as the graphics shown in this manual.

Chapter 1: Introduction

1-3

X10SAT Motherboard Layout

Important Notes to the User

•See Chapter 2 for detailed information on jumpers, I/O ports and JF1 front

panel connections.

•" " indicates the location of "Pin 1".

•Jumpers not indicated are for testing only.

•When LED1 (Onboard Power LED Indicator) is on, system power is on. Un-

plug the power cable before installing or removing any components.

1-4

X10SAT User’s Manual

Jumpers

Jumper Description Default

JBT1 Clear CMOS (See Chpt. 2)

JI2C1/JI2C2 SMB to PCI Slots Off (Disabled)

JPAC1 Audio Enable Pins 1-2 (Enabled)

JPL1/JPL2 LAN1/LAN2 Enable Pins 1-2 (Enabled)

JPME1 Intel Recovery Mode Pins 2-3 (Disabled)

JPME2 Intel Manufacturing Mode Pins 2-3 (Disabled)

JWD1 Watch Dog Enable Pins 2-3 (NMI)

JBR1 BIOS Recovery Mode Pins 2-3 (Disabled)

JPUSB1 USB Wake Up Enable (Back Panel) Pins 1-2 (Enabled)

JPUSB2 USB Wake Up Enable (USB Headers) Pins 1-2 (Enabled)

X10SAT Quick Reference

CLEAR CMOS SWITCH

A-SATA0I-SATA0

I-SATA1

I-SATA2

PCIE3

PCIE5

PCIE1

JPUSB2

1

3

JPUSB1

13

JLED1

JVR2

1

3

JPL1

1

JBR1

1

JPME2

1

JPL2

1

JPAC1

1

JPME1

1

3

JWD1

1

3

JVR1

1

3

JBT1

JSTBY1

1

3

JSD1

+

1

5

19

10

11

11

10

19

1

13

JPCIE2 JPCIE6

JPCIE4

1

DESIGNED IN USA

X10SAT

BIOS LICENSE

FOR HOME OR OFFICE USE

With FCC Standards

Tested to Comply

19

20

JTPM1

1

2

JPW2

1

1

7

10

10

7

2

1

1

JPEX_DEBUG

JL1

1

JSPDIF_OUT

1

JI2C1

1

JI2C2

1

24

13

JPW1

1

59

1

JITP1

2

R298

R97

SP1

1

4

4

1

FAN2

FAN5

1

4

1

FAN1

4

FAN4

1

1

JD1

4

THUNDERBOLT

USB 6/7(3.0)

USB 16/17

USB 4/5(3.0)

USB 14/15

USB 2/3(3.0)

USB 0/1(3.0)

CPU

CPU_SLOT2 PCI-E 3.0 X4 (IN X16)

PCH_SLOT1 PCI-E 2.0 X1 (INX4)

PCH_SLOT5 PCI-E 2.0 X1 (INX4)

PCH_SLOT3 PCI-E 2.0 X1 (INX4)

USB12/13

LAN2

LAN1

HDMI

JWD1:

JBR1:

2-3:BIOS RECOVERY

1-2:NORMAL

JPME1:

2-3:ME RECOVERY

1-2:NORMAL

ENABLE

LAN2

DISABLE

2-3

1-2

JPL2

LAN1

DISABLE

ENABLE

2-3

1-2

JPL1

JWOR1:

2-3:NMI

1-2:RST

WATCH DOG

2-3:ME MANUFACTURING MODE

USB 0/1

1-2:NORMAL

JPME2:

JTPM1:TPM/PORT80

JLED1:
3 PIN POWER LED

AUDIO FP

HDDPWR

LEDLED

P1-DIMMB1

P1-DIMMB2

NIC1

SPEAKER:1-4

JD1:

BUZZER:3-4

JI2C1/JI2C2

ON:ENABLE

OFF:DISABLE

NIC2

HD AUDIO

WAKE ON RING

USB4/5

USB6/7

OH/FF
LED

X

P1-DIMMA1

P1-DIMMA2

RST

PWR

JF1

ON

ALWAYS POPULATE BLUE SOCKET FIRST
UNB NON-ECC DDR3 DIMM REQUIRED

CPU_SLOT4 PCI-E 3.0 X8 (IN X16)

CPU_SLOT6 PCI-E 3.0 X16

COM1

VGA/DVI

2-3:DISABLE

1-2:ENABLE

JPAC1:AUDIO

POWER BUTTON

USB 2/3

CPU

A-SATA1I-SATA3

I-SATA4
I-SATA5

BATTERY

2

1

J_1394

1

1

T-SGPIO2

T-SGPIO1

Chapter 1: Introduction

1-5

Connectors and Switches

Connector Description

I/O Back Panel See page 2-16 for details

Audio FP Front Panel Audio Header

Battery Onboard Battery

COM1 COM1 Port Header

Fan 1,2,3,4,5 System/CPU Fan Headers (Fan1: CPU Fan)

JD1 Speaker/buzzer (Pins 1-2: Buzzer, Pins 1~4: External Speaker)

JF1 Front Panel Control Header

JL1 Chassis Intrusion Header

JL2 Reserved

JLED1 Power LED Indicator Header

JPW1 24-pin ATX Main Power Connector (Required)

JPW2 +12V 4-pin CPU power Connector (Required)

JSD1 SATA DOM (Disk On Module) Power Connector

JSPDIF_OUT Sony/Philips Digital Interface (S/PDIF) Out Header

JSTBY1 Standby Power Header

JTPM1 Trusted Platform Module/Port 80 Connector

SP1 Internal Speaker/Buzzer

A-SATA0/1 (ASMedia) Serial ATA (SATA 3.0) Port 0 / Port 1(6Gb/sec)

I-SATA0~5 (Intel C226) Serial ATA (SATA 3.0) Ports 0~5 (6Gb/sec)

USB 0/1 Front Panel Accessible USB 3.0 Ports 0/1 (USB 2.0 12/13)

USB 2/3 Front Panel Accessible USB 3.0 Ports 2/3 (USB 2.0 2/3)

USB 4/5, 6/7 Front Panel Accessible USB 2.0 Headers 4/5,6/7

POWERBUTTON Internal Power Button

CLEAR CMOS Resets the contents of the CMOS to default values

J_1394 1394 (Firewire®) Header

T-SGPIO1 / 2 Serial Link General Purpose Header

LED Indicators

LED Description Color/State Status

LED1 Onboard Standby PWR LED Green: Solid on Power On

1-6

X10SAT User’s Manual

Motherboard Features

CPU Single 4th Generation Intel® Core™ i7/i5/i3 DT processor,

E3-1200 V3 series processor in an LGA1150 socket.

Memory Four (4) SDRAM slots support up to 32 GB of DDR3 Unbuf-

fered, Non-ECC 1600/1333/1066 MHz memory

Single-channel memory

DIMM sizes

UDIMM 1 GB, 2 GB, 4GB, and 8GB

Chipset Intel® C226 Express

Expansion Slots Three (3) PCI Express 2.0 x1 (in x4) slots

One (1) PCI Express 3.0 x16/x8/x4 (in x16) slot*

One (1) PCI Express 3.0 x8/x4 (in x16) slot*

One (1) PCI Express 3.0 x4 (in x16) slot*

Network Connections Two (2) Gigabit Ethernet Controllers:

LAN1: Intel i217 gigabit LAN controller
LAN2: Intel i210 gigabit LAN controller

Two (2) RJ-45 rear I/O panel connectors with Link and
Activity LEDs

I/O Devices SATA Connections

SATA 3.0 (6Gb/s) Two (2) A-SATA 0~1, via ASM1061

RAID 0, 1

SATA 3.0 (6Gb/s) Six (6) I-SATA 0~5, via Intel C226

RAID 0, 1, 5, 10

USB Devices

Two (2) USB 2.0 ports and Four (4) USB 3.0 ports on the
rear I/O panel

Four (4) Front-Accessible USB 2.0 ports on Two head­ers and Four (4) Front Accessible USB 3.0 ports on two
headers

Other I/O Ports

One (1) Thunderbolt Port (DP 1.1 from PCH, PCI-E x4)

One (1) DV-I Port

One (1) HDMI Port

One (1) Serial Port header (COM1)
One (1) IEEE1394 Header

*Note for VGA Cards: For a single VGA card, install the VGA card into the JPCIE6 (x16) slot. For SLI™ or
CrossFireX™ mode (two VGA cards linked), install one card each into JPCIE6 (x16) and JPCIE4 (x8) slots.

Chapter 1: Introduction

1-7

Audio

One (1) High Denition Audio 7.1 channel connector sup-

ported by Realtek ALC1150 on the back panel

One (1) Front Panel Audio Header

One (1) SPDIF In/Out on the rear side of the chassis

Super I/O

Nuvoton NCT6776D

BIOS 128 Mb AMI BIOS® SPI Flash BIOS

Play and Plug (PnP0, DMI 2.3, PCI 2.3, ACPI 1.0/2.0/3.0,
USB Keyboard and SMBIOS 2.5

Power Conguration ACPI/ACPM Power Management

Main Switch Override Mechanism

Keyboard Wake-up from Soft-Off

Internal/External Modem Ring-On

Power-on mode for AC power recovery

PC Health Monitoring CPU Monitoring

Onboard voltage monitors for CPU core, +3.3V, +5V,-12V,
+12V, +3.3V Stdby, +5V Stdby, VBAT, Memory, VCORE
for CPU

CPU 6-phase switching voltage regulator

CPU/System overheat LED and control

CPU Thermal Trip support

Thermal Monitor 2 (TM2) support

Fan Control

Fan status monitoring with rmware 4-pin fan speed con­trol via SIO interface

Low noise fan speed control

System Management PECI (Platform Environment Conguration Interface) 2.0

support

System resource alert via SuperDoctor® III

SuperDoctor® III, Watch Dog, NMI

One (1) CMOS Reset Button on the rear panel

Chassis Intrusion header and detection

CD Utilities BIOS ash upgrade utility

Drivers and software for Intel® C226 Express chipset
utilities

Other ROHS 6/6 (Full Compliance, Lead Free)

Dimensions ATX form factor (12.0" x 9.6") (304.8 mm x 243.84 mm)

1-8

X10SAT User’s Manual

System Block Diagram

Note: This is a general block diagram and may not exactly represent

the features on your motherboard. See the Motherboard Features

pages for the actual specications of each motherboard.

X10SAT Block Diagram

1600/1333/1066MHz

4 USB 3.0 PORTS

USB3.0
5Gbps

INTEL LGA1150

VRD12.5

PCIe x16 SLOT #6

VRM 12.5

SVID

DDR3 (CHA)

DDR3 (CHB)

DIMM1A (Blue)

DIMM2A (Blue)

1600/1333/1066MHz

x4 DMI
5GT/s

PCIe2.0_x1

PCIe x1 SLOT #1

PCIe2.0_x1

PCIe x1 SLOT #3

10 USB 2.0 PORTS

USB2.0
480Mbps

6SATA-III PORTS

SATA-III
600MB/s

RJ45

PCIe2.0_x1

2.5GT/s

GLAN1
i217V

Lynx Point
Z87/C226

Intel

PCH

Haswell - DT

(Socket-H3)

LPC

TPM1.2(Header)

COM1

LPC

HEALTH
INFO

LPC I/O

NCT6776D

FLASH
SPI 128Mb

SPI

x2 FDI

2.7 Gbps

Analogl port A

VGA

RealTek ALC1150

AZALIA

PCIe3.0_x8

8.0GT/s

2.5GT/s

PCIe2.0_x1

PCIe x1 SLOT #5

HDMI

DVI

PCIe2.0_x1

2.5GT/s

GLAN2
i210IT

PCIe2.0_x1

2.5GT/s

ASM1061
SATA6G X2

RJ45

DIMM1B (Black)

DIMM2B (Black)

8.0GT/s

PCIe3.0_x4

PCIe x8(in x16) SLOT #4

1

2

4

3

PCIe3.0_x8

8.0GT/s

TI Switch

HD3SS3415

TI Switch
HD3SS3415

2

1

PCIe3.0_x8

8.0GT/s

8.0GT/s

PCIe3.0_x4

PCIe3.0_x4

PCIe x4(in x16) SLOT #2

PCIe3.0_x4

8.0GT/s

PCIe x4(in x16) SLOT #4

or

8.0GT/s

PCIe x8(in x16) SLOT #6

or

uPD720201
USB3.0 X4

2.5GT/s

2.5GT/s

2.5GT/s

PCIe2.0_x1

PLX8606

PCIe2.0_x1

2.5GT/s

PCIe2.0_x4

2.5GT/s

THUNDERBOLT

Mini-DP

CBTL05023BS

DP

Redwood Ridge

TI XIO2213B
IEEE1394 X1

2.5GT/s

PCIe2.0_x1

Chapter 1: Introduction

1-9

1-2 Chipset Overview

The X10SAT motherboard supports a single 4th Generation Intel® Core i7/i5/i3 DT

processor in the LGA 1150 Socket. Built upon the functionality and the capability

of the C226 Express chipset, the motherboard provides substantial enhancement

to system performance, including overclocking capability.

The high-speed Direct Media Interface (DMI) featured in the Intel C226 Express

chipset supports high-speed Direct Media Interface (DMI) for chip-to-chip true iso-

chronous communication, providing up to 10 Gb/s of software-transparent data

transfer rate on each read/write direction. In addition, the X10SAT also features a

TCO timer which allows the system to recover from a software/hardware lock and

perform tasks, including Function Disable and Intruder Detect.

Intel C226 Express Chipset Features

•Direct Media Interface (up 10 Gb/s transfer, Full Duplex)

•Intel® Matrix Storage Technology and Intel Rapid Storage Technology

•Dual NAND Interface

•Intel I/O Virtualization (VT-d) Support

•Intel Trusted Execution Technology Support

•PCI Express 2.0 Interface (up to 5.0 GT/s)

•SATA Controller (up to 6Gb/sec)

•Advanced Host Controller Interface (AHCI)

1-10

X10SAT User’s Manual

1-3 Special Features

Recovery from AC Power Loss

Basic I/O System (BIOS) provides a setting for you to determine how the system will

respond when AC power is lost and then restored to the system. You can choose

for the system to remain powered off, (in which case you must press the power

switch to turn it back on), or for it to automatically return to a power-on state. See

the Advanced BIOS Setup section to change this setting. The default setting is

Last State.

1-4 PC Health Monitoring

This section describes the PC health monitoring features of the board. All have an

onboard System Hardware Monitoring chip that supports PC health monitoring. An

onboard voltage monitor will scan these onboard voltages continuously: CPU Vcore,

12V, -12V, 5V, 5VSB, 3.3V, 3.3VSB, and Battery voltages. Once a voltage becomes

unstable, a warning is given, or an error message is sent to the screen. The user

can adjust the voltage thresholds to dene the sensitivity of the voltage monitor.

Fan Status Monitor with Firmware Control

PC health monitoring in the BIOS can check the RPM status of the cooling fans.

The onboard CPU and chassis fans are controlled by Thermal Management via

IPMI Firmware.

Environmental Temperature Control

The thermal control sensor monitors the CPU temperature in real time and will turn

on the thermal control fan whenever the CPU temperature exceeds a user-dened

threshold. The overheat circuitry runs independently from the CPU. Once the ther-

mal sensor detects that the CPU temperature is too high, it will automatically turn

on the thermal fans to prevent the CPU from overheating. The onboard chassis

thermal circuitry can monitor the overall system temperature and alert the user when

the chassis temperature is too high.

Note: To avoid possible system overheating, please be sure to provide

adequate airow to your system.

System Resource Alert

This feature is available when the system is used with SuperDoctor III in the

Windows OS environment or used with SuperDoctor II in Linux. SuperDoctor

Chapter 1: Introduction

1-11

is used to notify the user of certain system events. For example, you can also

congure SuperDoctor to provide you with warnings when the system temperature,

CPU temperatures, voltages and fan speeds go beyond predened thresholds.

1-5 ACPI Features

ACPI stands for Advanced Conguration and Power Interface. The ACPI specica-

tion denes a exible and abstract hardware interface that provides a standard

way to integrate power management features throughout a PC system, including

its hardware, operating system and application software. This enables the system

to automatically turn on and off peripherals such as CD-ROMs, network cards, hard

disk drives and printers.

In addition to enabling operating system-directed power management, ACPI also

provides a generic system event mechanism for Plug and Play, and an operating

system-independent interface for conguration control. ACPI leverages the Plug and

Play BIOS data structures, while providing a processor architecture-independent

implementation that is compatible with Windows 7, Windows 8, and Windows 2008

Operating Systems.

Slow Blinking LED for Suspend-State Indicator

When the CPU goes into a suspend state, the chassis power LED will start to blink

to indicate that the CPU is in suspend mode. When the user presses any key, the

CPU will "wake up", and the LED will automatically stop blinking and remain on.

1-6 Power Supply

As with all computer products, a stable power source is necessary for proper and

reliable operation. It is even more important for processors that have high CPU

clock rates.

This motherboard accommodates 24-pin ATX power supplies. Although most

power supplies generally meet the specications required by the CPU, some are

inadequate. In addition, the 12V 8-pin power connector located at JPW2 is also

required to ensure adequate power supply to the system. Also your power supply

must supply 1.5A for the Ethernet ports.

Warning: To prevent damage to the power supply or motherboard, please use a

power supply that contains a 24-pin and a 8-pin power connectors. Be sure to con-

nect these connectors to the 24-pin (JPW1) and the 8-pin (JPW2) power connectors

on the motherboard.

It is strongly recommended that you use a high quality power supply that meets ATX

power supply Specication 2.02 or above. It must also be SSI compliant. (For more

1-12

X10SAT User’s Manual

information, please refer to the web site at http://www.ssiforum.org/). Additionally, in

areas where noisy power transmission is present, you may choose to install a line

lter to shield the computer from noise. It is recommended that you also install a

power surge protector to help avoid problems caused by power surges.

1-7 Super I/O

The Super I/O supports two high-speed, 16550 compatible serial communication

ports (UARTs). Each UART includes a 16-byte send/receive FIFO, a programmable

baud rate generator, complete modem control capability and a processor interrupt

system. Both UARTs provide legacy speed with baud rate of up to 115.2 Kbps

as well as an advanced speed with baud rates of 250 K, 500 K, or 1 Mb/s, which

support higher speed modems.

The Super I/O provides functions that comply with ACPI (Advanced Conguration

and Power Interface), which includes support of legacy and ACPI power manage-

ment through an SMI or SCI function pin. It also features auto power management

to reduce power consumption.

Chapter 2: Installation

2-1

Chapter 2

Installation

2-1 Standardized Warning Statements

The following statements are industry-standard warnings, provided to warn the user

of situations which have the potential for bodily injury. Should you have questions or

experience difculty, contact Supermicro's Technical Support department for assis-

tance. Only certied technicians should attempt to install or congure components.

Read this section in its entirety before installing or conguring components in the

Supermicro chassis.

Battery Handling

Warnung

Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die

Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.

Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.

Warning!

There is a danger of explosion if the battery is replaced incorrectly. Replace the

battery only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's instructions

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。 交換する電池はメー
カーが推奨する型、または同等のものを使用下さい。 使用済電池は製造元の指示に従
って処分して下さい。

警告

电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更

换原有电池。请按制造商的说明处理废旧电池。

警告

電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有

電池。請按照製造商的說明指示處理廢棄舊電池。

2-2

X10SAT User’s Manual

Attention

Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer

que par une pile de type semblable ou équivalent, recommandée par le fabricant.

Jeter les piles usagées conformément aux instructions du fabricant.

¡Advertencia!

Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Re-

emplazar la batería exclusivamente con el mismo tipo o el equivalente recomen-

dado por el fabricante. Desechar las baterías gastadas según las instrucciones

del fabricante.

!הרהזא

תנכס תמייקץוציפ .הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי

גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ.

תוללוסה קוליס תושמושמה עצבל שי .ןרציה תוארוה יפל









경고!

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일
하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다. 제조사
의 안내에 따라 사용된 배터리를 처리하여 주십시오.

Waarschuwing

Er is ontplofngsgevaar indien de batterij verkeerd vervangen wordt. Vervang de

batterij slechts met hetzelfde of een equivalent type die door de fabrikant aan-

bevolen wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften

afgevoerd te worden.

Chapter 2: Installation

2-3

Product Disposal

Warning!

Ultimate disposal of this product should be handled according to all national laws

and regulations.

製品の廃棄

この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が

ありま す。

警告
本产品的废弃处理应根据所有国家的法律和规章进行。

警告
本產品的廢棄處理應根據所有國家的法律和規章進行。

Warnung

Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen

des Landes erfolgen.

¡Advertencia!

Al deshacerse por completo de este producto debe seguir todas las leyes y regla-

mentos nacionales.

Attention

La mise au rebut ou le recyclage de ce produit sont généralement soumis à des

lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de

l'organisme compétent.

רצומה קוליס

!הרהזא

ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס.הנידמה יקוח

2-4

X10SAT User’s Manual

2-2 Static-Sensitive Devices

Electrostatic-Discharge (ESD) can damage electronic com ponents. To avoid dam-

aging your system board, it is important to handle it very carefully. The following

measures are generally sufcient to protect your equipment from ESD.

Precautions

• Use a grounded wrist strap designed to prevent static discharge.

• Touch a grounded metal object before removing the board from the antistatic

bag.

• Handle the board by its edges only; do not touch its components, peripheral

chips, memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the motherboard and peripherals back into their antistatic bags when not in

use.

• For grounding purposes, make sure your computer chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and

the motherboard.

• Use only the correct type of onboard CMOS battery. Do not install the onboard

battery upside down to avoid possible explosion.

Unpacking

The motherboard is shipped in antistatic packaging to avoid static damage. When

unpacking the board, make sure that the person handling it is static protected.

Waarschuwing

De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming

met alle nationale wetten en reglementen.

 

경고!

이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.

Chapter 2: Installation

2-5

2-3 Processor and Heatsink Installation

Warning: When handling the processor package, avoid placing direct pressure on the

label area of the fan.

Important:

•Always connect the power cord last, and always remove it before adding,

removing or changing any hardware components. Make sure that you install

the processor into the CPU socket before you install the CPU heatsink.

•If you buy a CPU separately, make sure that you use an Intel-certied multi-

directional heatsink only.

•Make sure to install the system board into the chassis before you install

the CPU heatsink.

•When receiving a server board without a processor pre-installed, make sure

that the plastic CPU socket cap is in place and none of the socket pins are

bent; otherwise, contact your retailer immediately.

•Refer to the Supermicro website for updates on CPU support.

Load Lever

Installing the LGA1150 Processor

1. Press the load lever to release the load plate, which covers the CPU socket,

from its locking position.

Load Plate

2-6

X10SAT User’s Manual

2. Gently lift the load lever to open the load plate. Remove the plastic cap.

3. Use your thumb and your index nger to hold the CPU at the North center

edge and the South center edge of the CPU.

4. Align the CPU key that is the semi-circle cutouts against the socket keys.

Once it is aligned, carefully lower the CPU straight down into the socket. (Do

not drop the CPU on the socket. Do not move the CPU horizontally or verti-

cally.

South Center Edge

North Center Edge