Supero SUPER STORAGE SYSTEM 6047R-E1R24L User Manual

®

SUPER STORAGE SYSTEM

6047R-E1R24L

SUPER

USER’S MANUAL

1.0

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu­mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTW ARE, OR DA TA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environ­ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the manufacturer’s instruction manual, may cause harmful interference
with radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case you will be required to correct the interference at your own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn­ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to the
State of California to cause birth defects and other repro­ductive harm.

Manual Revision 1.0
Release Date: September 26, 2012

Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.

Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2012 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

iii

Preface

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the 6047R-E1R24L. Installation
and maintainance should be performed by experienced technicians only.

The 6047R-E1R24L is a high-end storage system based on the SC846E16­R920B 4U rackmountable chassis and the X9DRD-7LN4F-JBOD dual processor
serverboard.

Manual Organization

Chapter 1: Introduction

The fi rst chapter provides a checklist of the main components included with the
system and describes the main features of the X9DRD-7LN4F-JBOD serverboard
and the SC846E16-R920B chassis.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the 6047R-E1R24L into a rack
and check out the server confi guration prior to powering up the system. If your server
was ordered without processor and memory components, this chapter will refer you
to the appropriate sections of the manual for their installation.

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.

Chapter 4: System Safety

You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
6047R-E1R24L.

SUPERSTORAGESYSTEM 6047R-E1R24L User's Manual

iv

Chapter 5: Advanced Serverboard Setup

Chapter 5 provides detailed information on the X9DRD-7LN4F-JBOD serverboard,
including the locations and functions of connections, headers and jumpers. Refer
to this chapter when adding or removing processors or main memory and when
reconfi guring the serverboard.

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the SC846E16-R920B chassis. You
should follow the procedures given in this chapter when installing, removing or
reconfi guring SATA or peripheral drives and when replacing system power supply
units and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed informa­tion on running the CMOS Setup Utility.

Appendix A: BIOS Error Beep Codes

Appendix B: System Specifi cations

Notes

Preface

v

vi

Table of Contents

Chapter 1 Introduction

1-1 Overview .........................................................................................................1-1

1-2 Serverboard Features .....................................................................................1-2

Processors ......................................................................................................1-2

Memory ...........................................................................................................1-2

SAS .................................................................................................................1-2

Serial ATA ........................................................................................................1-2

PCI Expansion Slots ....................................................................................... 1-2

1-3 Server Chassis Features ................................................................................1-3

System Power ................................................................................................. 1-3

Hard Drives .....................................................................................................1-3

Front Control Panel .........................................................................................1-3

Cooling System ............................................................................................... 1-3

1-4 Contacting Supermicro ....................................................................................1-6

Chapter 2 Server Installation

2-1 Overview .........................................................................................................2-1

2-2 Unpacking the System .................................................................................... 2-1

2-3 Preparing for Setup .........................................................................................2-1

Choosing a Setup Location .............................................................................2-1

Rack Precautions ............................................................................................ 2-2

Server Precautions ..........................................................................................2-2

Rack Mounting Considerations .......................................................................2-3

Ambient Operating Temperature ................................................................ 2-3

Reduced Airfl ow .........................................................................................2-3

Mechanical Loading ................................................................................... 2-3

Circuit Overloading .....................................................................................2-3

Reliable Ground ......................................................................................... 2-3

2-4 Rack Mounting Instructions .............................................................................2-4

Rack Rails Assembly ...................................................................................... 2-4

Identifying the Inner Rack Rails ...................................................................... 2-4

Installing the Inner Rails on the Chassis ........................................................2-5

Installing the Outer Rails onto a Rack ............................................................ 2-6

Installing the Chassis into a Rack...................................................................2-8

Chapter 3 System Interface

3-1 Overview .........................................................................................................3-1

3-2 Control Panel Buttons ..................................................................................... 3-1

SUPERSTORAGESYSTEM 6047R-E1R24L User's Manual

vii

Reset ...............................................................................................................3-1

Power ..............................................................................................................3-1

3-3 Control Panel LEDs ........................................................................................3-1

Power Fail .......................................................................................................3-2

Overheat/Fan Fail ........................................................................................... 3-2

NIC1 ................................................................................................................3-2

NIC2 ................................................................................................................3-2

HDD .................................................................................................................3-3

Power ..............................................................................................................3-3

3-4 Drive Carrier LEDs ..........................................................................................3-3

Chapter 4 System Safety

4-1 Electrical Safety Precautions .......................................................................... 4-1

4-2 General Safety Precautions ............................................................................4-2

4-3 ESD Precautions ............................................................................................. 4-3

4-4 Operating Precautions .................................................................................... 4-4

Chapter 5 Advanced Serverboard Setup

5-1 Handling the Serverboard ............................................................................... 5-1

Precautions .....................................................................................................5-1

Unpacking .......................................................................................................5-2

5-2 Connecting Cables .......................................................................................... 5-2

Connecting Data Cables ................................................................................. 5-2

Connecting Power Cables ..............................................................................5-2

Connecting the Control Panel ......................................................................... 5-2

5-3 Rear I/O Ports ................................................................................................. 5-3

5-4 Installing the Processor and Heatsink ............................................................ 5-4

Installing an LGA2011 Processor ....................................................................5-4

Installing a Passive CPU Heatsink ................................................................. 5-7

Removing the Heatsink ................................................................................... 5-8

5-5 Installing Memory ............................................................................................5-9

Memory Support .............................................................................................. 5-9

DIMM Installation ............................................................................................ 5-9

5-6 Adding PCI Add-On Cards ............................................................................ 5-14

5-7 Serverboard Details ...................................................................................... 5-15

X9DRD-7LN4F-JBOD Quick Reference ....................................................... 5-16

5-8 Connector Defi nitions ................................................................................... 5-18

5-9 Jumper Settings ............................................................................................ 5-25

5-10 Onboard Indicators ........................................................................................5-27

5-11 SATA Ports ....................................................................................................5-28

Table of Contents

viii

5-12 Installing Software ......................................................................................... 5-29

SuperDoctor III .............................................................................................. 5-30

Chapter 6 Advanced Chassis Setup

6-1 Static-Sensitive Devices ..................................................................................6-1

Precautions .....................................................................................................6-1

Unpacking .......................................................................................................6-1

6-2 Control Panel ..................................................................................................6-2

6-3 Removing the Chassis Cover ......................................................................... 6-3

6-4 System Fans ................................................................................................... 6-4

System Fan Failure .........................................................................................6-4

Replacing System Fans ..................................................................................6-4

Rear Exhaust Fans ......................................................................................... 6-4

6-5 Drive Bay Installation/Removal .......................................................................6-5

Accessing the Drive Bays ...............................................................................6-5

SATA Drive Installation ....................................................................................6-6

Hard Drive Backplane ................................................................................ 6-7

Changing the CD-ROM or DVD-ROM and HDD Trays .............................6-8

Removing the Air Shroud ...............................................................................6-11

6-6 Power Supply ................................................................................................6-12

Power Supply Failure ....................................................................................6-12

6-7 Attaching a JBOD Expansion Chassis .......................................................... 6-13

Chapter 7 BIOS

7-1 Introduction ...................................................................................................... 7-1

Starting BIOS Setup Utility .............................................................................. 7-1

How To Change the Confi guration Data .........................................................7-2

Starting the Setup Utility ................................................................................. 7-2

7-2 Main Setup ...................................................................................................... 7-2

7-3 Advanced Setup Confi gurations......................................................................7-4

7-4 Event Logs .................................................................................................... 7-25

7-5 IPMI ............................................................................................................... 7-27

7-6 Boot ............................................................................................................... 7-29

7-7 Secur ity .........................................................................................................7-30

7-8 Save & Exit ................................................................................................... 7-31

Appendix A BIOS Error Beep Codes
Appendix B System Specifi cations

SUPERSTORAGESYSTEM 6047R-E1R24L User's Manual

Chapter 1

Introduction

1-1 Overview

The 6047R-E1R24L is a high-end storage system comprised of two main subsys­tems: the SC846E16-R920B 4U/rack mount chassis and the X9DRD-7LN4F-JBOD
dual processor serverboard. Please refer to our web site for information on operating
systems that have been certifi ed for use with the system (www.supermicro.com).

In addition to the serverboard and chassis, various hardware components have
been included with the 6047R-E1R24L, as listed below:

• Two passive CPU heatsinks (SNK-P0048PS)

• Three 8-cm system fans (FAN-0127L4)

• Two rear exhaust fans (FAN-0125L4)

• One air shroud (MCP-310-49003-0N)

• SATA Accessories

One SATA backplane (BPN-SAS2-846EL1)
Twenty-four drive carriers (MCP-220-00075-OB)
JBOD Expansion Port (CBL-0352L)

• One rackmount kit (MCP-290-00057-0N)

• One CD containing drivers and utilities

Note: a complete list of safety warnings is provided on the Supermicro web site at
http://www.supermicro.com/about/policies/safety_information.cfm

Chapter 1: Introduction

1-1

1-2

SUPERSTORAGESYSTEM 6047R-E1R24L User's Manual

1-2 Serverboard Features

The 6047R-E1R24L is built around the X9DRD-7LN4F-JBOD, a dual processor
serverboard based on the Intel C602J chipset. Below are the main features of the
X9DRD-7LN4F-JBOD. (See Figure 1-1 for a block diagram of the chipset).

Processors

The X9DRD-7LN4F-JBOD supports single or dual Intel® Xeon E5-2600 Series
processors. Please refer to the serverboard description pages on our web site for
a complete listing of supported processors (www.supermicro.com).

Memory

The X9DRD-7LN4F-JBOD has 16 DIMM slots that can support 512 GB of ECC
DDR3 Registered memory (RDIMM) or up to 128 GB of ECC/non-ECC DDR3
Unbuffered memory (UDIMM). See Chapter 5 for details.

SAS

A SAS 2.0 controller is integrated into the serverboard providing 8x lanes of 6Gb/s
SAS with basic HBA/ITMode controller functionality. The controller supports the
attachment of 122 SAS or SATA devices.

Serial ATA

A SATA controller is also integrated into the chipset to provide two SATA 3 (6/Gbps)
and four SATA 2 (3 Gbps) ports, which are RAID 0, 1, 5 and 10 supported. The
SATA drives are hot-swappable units.

PCI Expansion Slots

The X9DRD-7LN4F-JBOD has six PCI-E 3.0 x8 slots. The default confi guration
includes a port plate with dual JBOD expansion ports occupying slot #1 (PCI-E 3.0
x8). Note that expansion slots are controlled by the CPUs, so two CPUs need to
be installed to enable all PCI expansion slots. See Chapter 5 for details.

1-3

Chapter 1: Introduction

1-3 Server Chassis Features

The following is a general outline of the main features of the SC846E16-R920B
server chassis.

System Power

The SC846E16-R920B features a redundant (two separate power modules) 920W
high-effi ciency power supply with I2C. This power redundancy feature allows you to
replace a failed power supply without shutting down the system.

Hard Drives

The SC846E16-R920B chass is was designed to sup port 24 dual -channel S ATA
hard dr ives, w hich a re hot- swap pabl e unit s. 2x 2 .5" re ar mou nted hot- swa p drive
bays are availa ble as an opti on for use w ith the onb oard SATA contro ller (MC P­220-846 06 - 0 N)

Note: The operati ng system yo u use must h ave R AID su ppor t to e nable t he hot­swap capability of the SATA drives.

Front Control Panel

The control panel on the SuperServer 6047R-E1R24L provides you with system
monitoring and control. LEDs indicate system power, HDD activity, network activ­ity, system overheat/fan fail and power supply failure. A main power button and a
system reset button are also included. In addition, two USB ports and a COM port
have been incorporated into the front of the chassis for convenient access.

Cooling System

The SC846E16-R920B chassis includes three 8-cm hot-plug system cooling fans
located in the middle section of the chassis. An air shroud channels the airfl ow from
the system fans to effi ciently cool the processors and memory. Two additional 8-cm
fans are located at the back of the chassis to expel hot air from the system. Each
power supply module also includes a cooling fan.

1-4

SUPERSTORAGESYSTEM 6047R-E1R24L User's Manual

Figure 1-1. Intel C602J Chipset:

System Block Diagram

Note: This is a general block diagram. Please see Chapter 5 for details.

J23 SLOT#3

PCIE 3.0 x8

J24 SLOT#4

PCIE 3.0 x8

J25 SLOT#5

PCIE 3.0 x8

P0 P1

PE2
(AB)

PE2
(CD)

PE1
(AB)

DMI

DDR3 DIMM

CPU REAR

PROCESSOR

SANDYBRIDGE

PROCESSOR

SANDYBRIDGE

F

E

Socket 01

#2

#1

DDR3 DIMM

#2

#1

PE3

J22 SLOT#2
PCIE 3.0 x8

PCIE 3.0 x8

PCIE 3.0 x8
PCIE 3.0 x4

SAS

LSI

LAN1

LAN2

RJ45 RJ45
LAN3 LAN4

VGA CONN

IPMI LAN

PHY
RTL8201F

RJ45 RJ45

SAS2308

Powerville
I350-AM4
Quad GLAN

J26 SLOT#6

L-SAS0~3
L-SAS4~7

J21 SLOT#1
PCIE 3.0 x8

DDR3 DIMM

H

G

#2

#1

DDR3 DIMM

#2

#1

P1 P0

PE2
(AB)

PE2
(CD) (AB) (CD)

PE1
(AB)

PE3

DMI

PCH C602J

BIOS

SATA

SPI

SATA Gen3
6Gbps

SATA Gen3
6Gbps

SATA

SATA [0..1]

SCU0

USB

LPCPCI 32

SPI FLASH

DDR3 DIMM

CPU FRONT

D

C

Socket 00

#2

#1

#2

#1

PE3

DDR3 DIMM

B

A

#2

#1

DDR3 DIMM

QPI

QPI

#2

#1

I-SATA0

I-SATA1

S-SATA0

S-SATA1

S-SATA2

S-SATA3

REAR

HDR 2X5

0,1

TYPE-A

REAR

2,3

4,5 6 8,9

HDR 2X5

TPM HDR

Port 80

HERMON

WPCM450]

NCT7904D

HW Monitor

DDR3

DDR3 DIMM

1-5

Chapter 1: Introduction

Figure 1-2. X9DRD-7LN4F-JBOD Serverboard

Note: The SSG-6047R-E1R24L comes pre-installed with a JBOD expansion port

installed in PCI-E slot 1. Serverboard SAS components shown in the fi gure above
are not included on the X9DRD-7LN4F-JBOD

JPME1

JI2C1

VGA1

I-SATA1

I-SATA0

I-SATA5

I-SATA4

I-SATA3

I-SATA2

JIPMB1

JPME2

JPL1

JBR1

JWD1

JPG1

JPB1

JVRM_I2C1

JVRM_I2C2

JVR1

FAN5

FAN6

FAN8

FAN7

FAN1

FAN2

FAN3

FAN4

JF2

T-SGPIO1

T-SGPIO2

JUSB6

JSD1

JBT1

JBAT1

JTPM1

JF1

JPI2C1

JOH1

JI2C2

JL1

JSTBY1

JUIDB

J4

JD1

LED3

LEDM1

LED2

LAN2/4

LAN1/3

CPU1

CPU2

CPU2

CPU1

CPU2

CPU1

PWR I2C

UID

P2-DIMME1

P2-DIMMF2

P2-DIMMF1

P2-DIMMG2

P2-DIMMG1

P2-DIMMH2

P2-DIMMH1

P1-DIMMA2

P1-DIMMA1

P1-DIMMB2

P1-DIMMB1

P1-DIMMC1

P1-DIMMC2

P1-DIMMD1

P1-DIMMD2

USB4/5USB8/9

SLOT1 PCI-E 3.0 X8

SLOT2 PCI-E 3.0 X8

SLOT3 PCI-E 3.0 X8

SLOT4 PCI-E 3.0 X8

SLOT5 PCI-E 3.0 X8

USB6

TPM/PORT80

BUZZER

CMOS CLEAR

SLOT6 PCI-E 3.0 X8

COM2

USB2/3

COM1

USB0/1

SP1

CPU2

IPMI_LAN

CPU2

CPU2

Battery

BIOS

JPW1

JPW2

24-Pin Main PWR

8-Pin PWR

JPW4

P2-DIMME2

JPW3

8-Pin PWR

4-Pin PWR

L-SAS4~7

L-SAS0~3

LSI SAS CTRL

Intel
PCH

JPS1

LAN
CTRL

BMC

CPU1

X9DRD-7(J)LN4F

Rev. 1.01

JBOD Expansion Ports

1-6

SUPERSTORAGESYSTEM 6047R-E1R24L User's Manual

1-4 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.
San Jose, CA 95131 U.S.A.

Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands

Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)
[e-mail] (Customer Support)

Asia-Pacifi c

Address: Super Micro Computer, Inc.

4F, No. 232-1, Liancheng Rd.
Chung-Ho Dist., New Taipei City 235
Taiwan

Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [e-mail]
Tel: [phone], ext.132 or 139

Chapter 2: Server Installation

2-1

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your SuperServer 6047R­E1R24L up and running. Following these steps in the order given should enable
you to have the system operational within a minimum amount of time. This quick
setup assumes that your system has come to you with the processors and memory
preinstalled. If your system is not already fully integrated with a serverboard, pro­cessors, system memory etc., please turn to the chapter or section noted in each
step for details on installing specifi c components.

2-2 Unpacking the System

You should inspect the box the SuperServer 6047R-E1R24L was shipped in and
note if it was damaged in any way. If the server itself shows damage you should
fi le a damage claim with the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the SuperServer 6047R­E1R24L. It should be situated in a clean, dust-free area that is well ventilated. A void
areas where heat, electrical noise and electromagnetic fi elds are generated. You
will also need it placed near a grounded power outlet. Read the Rack and Server
Precautions in the next section.

2-3 Preparing for Setup

The box the SuperServer 6047R-E1R24L was shipped in should include two sets of
rail assemblies, two rail mounting brackets and the mounting screws you will need to
install the system into the rack. Follow the steps in the order given to complete the
installation process in a minimum amount of time. Please read this section in its en­tirety before you begin the installation procedure outlined in the sections that follow.

Choosing a Setup Location

• Leave enough clearance in front of the rack to enable you to open the front door

completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for suffi cient airfl ow and ease in servicing.

• This product is for installation only in a Restricted Access Location (dedicated

equipment rooms, service closets and the like).

2-2

SUPERSTORAGESYSTEM 6047R-E1R24L User's Manual

• This product is not suitable for use with visual display work place devices

acccording to §2 of the the German Ordinance for Work with Visual Display Units.

!

!

Warnings and Precautions!

Rack Precautions

• Ensure that the leveling jacks on the bottom of the rack are fully extended to

the fl oor with the full weight of the rack resting on them.

• In single rack installation, stabilizers should be attached to the rack. In multiple

rack installations, the racks should be coupled together.

• Always make sure the rack is stable before extending a component from the

rack.

• You should extend only one component at a time - extending two or more si-

multaneously may cause the rack to become unstable.

Server Precautions

• Review the electrical and general safety precautions in Chapter 4.

• Determine the placement of each component in the rack before you install the

rails.

• Install the heaviest server components on the bottom of the rack fi rst, and then

work up.

• Use a regulating uninterruptible power supply (UPS) to protect the server from

power surges, voltage spikes and to keep your system operating in case of a
power failure.

• Allow any hot plug drives and power supply modules to cool before touching

them.

• Always keep the rack's front door and all panels and components on the servers

closed when not servicing to maintain proper cooling.

Chapter 2: Server Installation

2-3

Rack Mounting Considerations

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating tempera­ture of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient tempera­ture (Tmra).

Reduced Airfl ow

Equipment should be mounted into a rack so that the amount of airfl ow required
for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.

Circuit Overloading

Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connec­tions other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).

2-4

SUPERSTORAGESYSTEM 6047R-E1R24L User's Manual

2-4 Rack Mounting Instructions

Rack Rails Assembly

This section provides information on installing the SC846 chassis into a rack unit
with the rails provided. There are a variety of rack units on the market, which may
mean that the assembly procedure will differ slightly. You should also refer to the
installation instructions that came with the rack unit you are using.

Note: This rail will fi t a rack between 27" and 34.45" deep.

Identifying the Inner Rack Rails

The chassis package includes a rack rail assembly in the rack mounting kit. Each
assembly consists of an inner rail that secures to the chassis and an outer rail that
is attached directly to the rack.

Figure 2-1. Identifying the Rack Rails

Inner Rail Assembly

Chapter 2: Server Installation

2-5

Figure 2-2. Installing the Rails

Installing the Inner Rails on the Chassis

Installing the Inner Rails

1. Place the inner rails on the side of the chassis aligning the hooks of the chas­sis with the inner rail holes. Make sure that the rail faces "outward" so that it
will fi t with the rack's mounting bracket.

2. Slide the rail toward the front of the chassis.

3. Secure the rail to the chassis with four screws as illustrated.

4. Repeat steps 1-3 for the other inner rack rail.

1

1

1

2

1

3

2-6

SUPERSTORAGESYSTEM 6047R-E1R24L User's Manual

Installing the Outer Rails onto a Rack

Installing the Outer Rails

1. Attach the short bracket to the outside of the long bracket. You must align the
pins with the slides. Also, both bracket ends must face the same direction.

2. Adjust both the short and long brackets to the proper distance so that the rail
fi ts snugly into the rack.

3. Secure the long bracket to the front side of the outer rail with two M5 screws
and the short bracket to the rear side of the outer rail with three M5 screws.

4. Repeat steps 1-4 for the remaining outer rail.

Secure to the

Front of the Rack

Secure to the

Rear of the Rack

Figure 2-3. Assembling the Outer Rails

Attach Outer Racks Together

Chapter 2: Server Installation

2-7

Figure 2-4. Installing the Outer Rails to the Server Rack

1

3

1

3

1

2

2-8

SUPERSTORAGESYSTEM 6047R-E1R24L User's Manual

Figure 2-5. Installing the Rack Rails

1

A

1

B

Installing the Chassis into a Rack

Installing the Chassis into a Rack

1. Confi rm that chassis includes the inner rails (A), also confi rm that the outer

rails (B) are installed on the rack.

2. Align chassis rails (A) with the front of the rack rails (B).

3. Slide the chassis rails into the rack rails, keeping the pressure even on both

sides (you may have to depress the locking tabs when inserting). When the
server has been pushed completely into the rack, you should hear the locking
tabs "click" into the locked position.

4. Tighten up all the screws on the front side and rear side of both outer rails.

5. (Optional) Insert and tightening the thumbscrews that hold the front of the

server to the rack.

Chapter 3: System Interface

3-1

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the control panel as well as others on the SCSI drive
carriers to keep you constantly informed of the overall status of the system as well
as the activity and health of specifi c components. There are also two buttons on
the chassis control panel.

3-2 Control Panel Buttons

The two push-buttons located on the front of the chassis are (in order from left to
right) a reset button and a power on/off button.

Reset

Use the reset button to reboot the system.

Power

This is the main power button, which is used to apply or turn off the main system
power. T urning off system power with this button removes the main power but keeps
standby power supplied to the system. Therefor e, the system powe r cord shou ld
be unplugged before performing service.

3-3 Control Panel LEDs

The control panel located on the front of the chassis has several LEDs. These
LEDs provide you with critical information related to different parts of the system.
This section explains what each LED indicates when illuminated and any corrective
action you may need to take.

3-2

SUPERSTORAGESYSTEM 6047R-E1R24L User's Manual

Power Fail

Indicates a power supply module has failed. The second power supply module will
take the load and keep the system running but the failed module will need to be
replaced. Refer to Chapter 6 for details on replacing the power supply. This LED
should be off when the system is operating normally.

Overheat/Fan Fail

When this LED fl ashes, it indicates a fan failure. When on continuously it indicates
an overheat condition, which may be caused by cables obstructing the airfl ow in
the system or the ambient room temperature being too warm. Check the routing of
the cables and make sure all fans are present and operating normally. You should
also check to make sure that the chassis covers are installed. Finally, verify that
the heatsinks are installed properly (see Chapter 5). This LED will remain fl ashing
or on as long as the indicated condition exists.

NIC1

Indicates network activity on the LAN1 port when fl ashing.

NIC2

Indicates network activity on the LAN2 port when fl ashing.

1

2

Chapter 3: System Interface

3-3

HDD

Indicates IDE channel activity. On the SuperServer 6047R-E1R24L, this LED
indicates hard and/or DVD-ROM drive activity when fl ashing.

Power

Indicates power is being supplied to the system's power supply units. This LED
should normally be illuminated when the system is operating.

3-4 Drive Carrier LEDs

Each drive carrier has two LEDs.

• Green: When illuminated, the green LED on the front of the drive carrier indi-

cates drive activity. A connection to the backplane enables this LED to blink on
and off when that particular drive is being accessed.

• Red: The SAF-TE compliant backplane activates the red LED to indicate a

drive failure. If one of the drives fail, you should be notifi ed by your system
management software. Please refer to Chapter 6 for instructions on replacing
failed drives.

3-4

SUPERSTORAGESYSTEM 6047R-E1R24L User's Manual

Notes

Chapter 4: System Safety

4-1

Chapter 4

System Safety

4-1 Electrical Safety Precautions

!

Basic electrical safety precautions should be followed to protect yourself from harm
and the SuperServer 6047R-E1R24L from damage:

• Be aware of the locations of the power on/off switch on the chassis as well

as the room's emergency power-off switch, disconnection switch or electrical
outlet. If an electrical accident occurs, you can then quickly remove power from
the system.

• Do not work alone when working with high voltage components.

• Power should always be disconnected from the system when removing or in-

stalling main system components, such as the serverboard, memory modules
and fl oppy drive. When disconnecting power, you should fi rst power down the
system with the operating system fi rst and then unplug the power cords of all
the power supply units in the system.

• When working around exposed electrical circuits, another person who is familiar

with the power-off controls should be nearby to switch off the power if neces­sary.

• Use only one hand when working with powered-on electrical equipment. This

is to avoid making a complete circuit, which will cause electrical shock. Use
extreme caution when using metal tools, which can easily damage any electrical
components or circuit boards they come into contact with.

• Do not use mats designed to decrease static electrical discharge as protection

from electrical shock. Instead, use rubber mats that have been specifi cally
designed as electrical insulators.

• The power supply power cords must include a grounding plug and must be

plugged into grounded electrical outlets.

4-2

SUPERSTORAGESYSTEM 6047R-E1R24L User's Manual

4-2 General Safety Precautions

Follow these rules to ensure general safety:

• Keep the area around the 6047R-E1R24L clean and free of clutter.

• The 6047R-E1R24L weighs approximately 75 lbs (34.1 kg.) when fully loaded.

When lifting the system, two people at either end should lift slowly with their
feet spread out to distribute the weight. Always keep your back straight and lift
with your legs.

• Place the chassis top cover and any system components that have been re-

moved away from the system or on a table so that they won't accidentally be
stepped on.

• While working on the system, do not wear loose clothing such as neckties and

unbuttoned shirt sleeves, which can come into contact with electrical circuits or
be pulled into a cooling fan.

• Remove any jewelry or metal objects from your body, which are excellent metal

conductors that can create short circuits and harm you if they come into contact
with printed circuit boards or areas where power is present.

!

• Serverboard Battery: CAUTION - There is a danger of explosion if the onboard

battery is installed upside down, which will reverse its polarites (see Figure 4-1).
This battery must be replaced only with the same or an equivalent type recom­mended by the manufacturer (CR2032). Dispose of used batteries according to
the manufacturer's instructions.

• DVD-ROM Laser: CAUTION - this server may have come equipped with a

DVD-ROM drive. To prevent direct exposure to the laser beam and hazardous
radiation exposure, do not open the enclosure or use the unit in any uncon­ventional way.

• Mainboard replaceable soldered-in fuses: Self-resetting PTC (Positive Tempera-

ture Coeffi cient) fuses on the mainboard must be replaced by trained service
technicians only. The new fuse must be the same or equivalent as the one
replaced. Contact technical support for details and support.

Chapter 4: System Safety

4-3

4-3 ESD Precautions

Electrostatic discharge (ESD) is generated by two objects with different electrical
charges coming into contact with each other. An electrical discharge is created to
neutralize this difference, which can damage electronic com ponents and printed
circuit boards. The following measures are generally suffi cient to neutralize this
difference before contact is made to protect your equipment from ESD:

• Use a grounded wrist strap designed to prevent static discharge.

• Keep all components and printed circuit boards (PCBs) in their antistatic bags

until ready for use.

• Touch a grounded metal object before removing the board from the antistatic

bag.

• Do not let components or PCBs come into contact with your clothing, which may

retain a charge even if you are wearing a wrist strap.

• Handle a board by its edges only; do not touch its components, peripheral chips,

memory modules or contacts.

• When handling chips or modules, avoid touching their pins.

• Put the serverboard and peripherals back into their antistatic bags when not

in use.

• For grounding purposes, make sure your computer chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and
the serverboard.

!

• After accessing the inside of the system, close the system back up and secure

it to the rack unit with the retention screws after ensuring that all connections
have been made.

4-4

SUPERSTORAGESYSTEM 6047R-E1R24L User's Manual

4-4 Operating Precautions

Care must be taken to assure that the chassis cover is in place when the 6047R­E1R24L is operating to assure proper cooling. Out of warranty damage to the system
can occur if this practice is not strictly followed.

!

Figure 4-1. Installing the Onboard Battery

LITHIUM BATTERY

BATTERY HOLDER

!

Please handle used batteries carefully. Do not damage the battery in any way; a
damaged battery may release hazardous materials into the environment. Do not
discard a used battery in the garbage or a public landfi ll. Please comply with the
regulations set up by your local hazardous waste management agency to dispose
of your used battery properly.

Note: a complete list of safety warnings is provided on the Supermicro web site at
http://super-dev/about/policies/safety_information.cfm