Supero SUPERSERVER 7045B-8R+, SUPERSERVER 7045B-TR+ User Manual

SUPER

SUPERSERVER 7045B-8R+

S

UPERSERVER 7045B-TR+

®

USER’S MANUAL

1.0a

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

SUPER MICRO COMPUTER reserves the right to make changes to the product described in this
manual at any time and without notice. This product, including software, if any, and documenta­tion may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any
medium or machine without prior written consent.

IN NO EVENT WILL SUPER MICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE
OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO SHALL NOT HAVE
LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE
PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING
OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for
all claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.

Manual Revision 1.0a

Release Date: July 10, 2007

Unless you request and receive written permission from SUPER MICRO COMPUTER, you may not
copy any part of this document.

Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2007 by SUPER MICRO COMPUTER INC.
All rights reserved.

Printed in the United States of America

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It

provides information for the installation and use of the SuperServer 7045B-8R+/

7045B-TR+. Installation and maintenance should be performed by experienced

technicians only.

The SuperServer 7045B-8R+/7045B-TR+ is a high-end server based on the

SC745S2-R800/SC745TQ-R800 tower/4U rackmount chassis and the X7DB8+/

X7DBE+, a dual processor serverboard that supports dual Intel

processors at a Front Side (System) Bus speed of 1066 MHz and up to 64 GB of

registered FBD ECC DDR2-667/533 SDRAM.

®

XeonTM LGA 771

Preface

Manual Organization

Chapter 1: Introduction

The fi rst chapter provides a checklist of the main components included with the

server system and describes the main features of the X7DB8+/X7DBE+ serverboard

and the SC745S2-R800/SC745TQ-R800 chassis, which comprise the SuperServer

7045B-8R+/7045B-TR+.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer 7045B-

8R+/7045B-TR+ into a rack and check out the server confi guration prior to pow-

ering up the system. If your server was ordered without processor and memory

components, this chapter will refer you to the appropriate sections of the manual

for their installation.

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions and

information provided by the control panel on the chassis as well as other LEDs

located throughout the system.

iii

SUPERSERVER 7045B-8R+/7045B-TR+ User's Manual

Chapter 4: System Safety

You should thoroughly familiarize yourself with this chapter for a general overview

of safety precautions that should be followed when installing and servicing the

SuperServer 7045B-8R+/7045B-TR+.

Chapter 5: Advanced Serverboard Setup

Chapter 5 provides detailed information on the X7DB8+/X7DBE+ serverboard,

including the locations and functions of connections, headers and jumpers. Refer

to this chapter when adding or removing processors or main memory and when

reconfi guring the serverboard.

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the SC745S2-R800/SC745TQ-R800

server chassis. You should follow the procedures given in this chapter when install-

ing, removing or reconfi guring SCSI /SATA or peripheral drives and when replacing

system power supply units and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed informa-

tion on running the CMOS Setup Utility.

Appendix A: BIOS POST Codes

Appendix B: Software Installation

Appendix C: System Specifi cations

iv

Notes

Preface

v

SUPERSERVER 7045B-8R+/7045B-TR+ User's Manual

Table of Contents

Preface

About This Manual ...................................................................................................... iii

Manual Organization ................................................................................................... iii

Chapter 1: Introduction

1-1 Overview ......................................................................................................... 1-1

1-2 Serverboard Features ..................................................................................... 1-2

1-3 Server Chassis Features ................................................................................ 1-4

1-4 Contacting Super Micro .................................................................................. 1-6

Chapter 2: Server Installation

2-1 Overview ......................................................................................................... 2-1

2-2 Unpacking the System ................................................................................... 2-1

2-3 Preparing for Setup ........................................................................................ 2-1

2-4 Installing the System into a Rack ................................................................... 2-4

2-5 Checking the Serverboard Setup ................................................................... 2-8

2-6 Checking the Drive Bay Setup ....................................................................... 2-9

Chapter 3: System Interface

3-1 Overview ......................................................................................................... 3-1

3-2 Control Panel Buttons .................................................................................... 3-1

Power ....................................................................................................... 3-1

Reset ........................................................................................................ 3-1

3-3 Control Panel LEDs ........................................................................................ 3-2

Power ....................................................................................................... 3-2

HDD .......................................................................................................... 3-2

NIC1 ......................................................................................................... 3-2

NIC2 ......................................................................................................... 3-2

Overheat/Fan Fail .................................................................................... 3-2

Power Fail ................................................................................................ 3-3

3-4 Drive Carrier LEDs ......................................................................................... 3-3

Chapter 4: System Safety

4-1 Electrical Safety Precautions .......................................................................... 4-1

4-2 General Safety Precautions ........................................................................... 4-2

4-3 ESD Precautions ............................................................................................ 4-3

4-4 Operating Precautions .................................................................................... 4-4

vi

Table of Contents

Chapter 5: Advanced Serverboard Setup

5-1 Handling the Serverboard .............................................................................. 5-1

5-2 Processor and Heatsink Installation ............................................................... 5-2

5-3 Connecting Cables ......................................................................................... 5-5

Connecting Data Cables .......................................................................... 5-5

Connecting Power Cables ....................................................................... 5-5

Connecting the Control Panel .................................................................. 5-6

5-4 I/O Ports ......................................................................................................... 5-7

5-5 Installing Memory ........................................................................................... 5-7

5-6 Adding PCI Cards ........................................................................................... 5-9

5-7 Serverboard Details ........................................................................................ 5-9

X7DB8+ Layout ...................................................................................... 5-10

X7DB8+ Quick Reference ...................................................................... 5-11

5-8 Connector Defi nitions ................................................................................... 5-12

ATX Power Connector ........................................................................... 5-12

Secondary Power Connector ................................................................. 5-12

Processor Power Connector .................................................................. 5-12

NMI Button ............................................................................................. 5-12

Power LED ............................................................................................. 5-12

HDD LED ............................................................................................... 5-13

NIC1 LED ............................................................................................... 5-13

NIC2 LED ............................................................................................... 5-13

Overheat/Fan Fail LED .......................................................................... 5-13

Power Fail LED ...................................................................................... 5-13

Reset Button .......................................................................................... 5-14

Power Button .......................................................................................... 5-14

Universal Serial Bus (USB0/1) ............................................................... 5-14

Chassis Intrusion .................................................................................... 5-14

Serial Ports ............................................................................................. 5-15

Power Fail Header ................................................................................. 5-15

Fan Headers .......................................................................................... 5-15

Extra Universal Serial Bus Headers ...................................................... 5-16

Power LED/Speaker ............................................................................... 5-16

ATX PS/2 Keyboard and Mouse Ports .................................................. 5-16

Overheat LED ........................................................................................ 5-16

Wake-On-LAN ........................................................................................ 5-17

Wake-On-Ring ........................................................................................ 5-17

SMB ........................................................................................................ 5-17

SMBUS_PS ............................................................................................ 5-17

vii

SUPERSERVER 7045B-8R+/7045B-TR+ User's Manual

Alarm Reset ........................................................................................... 5-18

SGPIO .................................................................................................... 5-18

5-9 Jumper Settings ............................................................................................ 5-18

Explanation of Jumpers ......................................................................... 5-18

CMOS Clear ........................................................................................... 5-19

JLAN Enable/Disable ............................................................................. 5-19

Watch Dog Enable/Disable .................................................................... 5-19

3rd Power Supply Fail Detect Enable/Disable ....................................... 5-20

VGA Enable/Disable ............................................................................... 5-20

SCSI Controller Enable/Disable ............................................................. 5-20

SCSI Termination Enable/Disable .......................................................... 5-21

Compact Flash Master/Slave Select ...................................................... 5-21

SMBUS to PCI Enable/Disable .............................................................. 5-21

5-10 Onboard Indicators ....................................................................................... 5-22

JLAN1/JLAN2 LEDs ............................................................................... 5-22

SCSI Activity LED Indicators .................................................................. 5-22

Onboard Power LED .............................................................................. 2-22

5-11 Parallel Port, Floppy and Hard Drive Connections ...................................... 5-23

Parallel Port Connector .......................................................................... 5-23

Floppy Connector ................................................................................... 5-24

SATA Ports ............................................................................................. 5-24

IDE Connectors ...................................................................................... 5-25

Ultra320 SCSI Connectors ..................................................................... 5-26

Chapter 6: Advanced Chassis Setup

6-1 Static-Sensitive Devices ................................................................................. 6-1

6-2 Front Control Panel ........................................................................................ 6-3

6-3 System Fans ................................................................................................... 6-4

Fan Failure ............................................................................................... 6-4

Replacing Chassis Cooling Fans ............................................................. 6-4

6-4 Drive Bay Installation ...................................................................................... 6-6

SAS/SATA Drives ..................................................................................... 6-6

Installing Components in the 5.25" Drive Bays ....................................... 6-8

6-5 Power Supply ................................................................................................. 6-9

Power Supply Failure ............................................................................... 6-9

Removing/Replacing the Power Supply ................................................... 6-9

viii

Table of Contents

Chapter 7: BIOS

7-1 Introduction ..................................................................................................... 7-1

7-2 Running Setup ................................................................................................ 7-2

7-3 Main BIOS Setup ............................................................................................ 7-2

7-4 Advanced Setup ............................................................................................. 7-7

7-5 Security ......................................................................................................... 7-19

7-6 Boot .............................................................................................................. 7-20

7-7 Exit ................................................................................................................ 7-21

Appendices:

Appendix A: BIOS POST Messages

Appendix B: BIOS POST Codes

Appendix C: Software Installation

Appendix D: System Specifi cations

ix

S

UPERSERVER 7045B-8R+/7045B-TR+ User's Manual

Notes

x

Chapter 1: Introduction

Chapter 1

Introduction

1-1 Overview

The SuperServer 7045B-8R+/7045B-TR+ is a high-end server that is comprised of

two main subsystems: the SC745S2-R800/SC745TQ-R800 tower/4U server chassis

and the X7DB8+/X7DBE+ dual Intel Xeon processor serverboard. Please refer to

our web site for information on operating systems that have been certifi ed for use

with the SuperServer 7045B-8R+/7045B-TR+ (www.supermicro.com).

In addition to the serverboard and chassis, various hardware components have been

included with the SuperServer 7045B-8R+/7045B-TR+, as listed below:

 Three (3) 8-cm hot-swap chassis fans (FAN-0072)

 Two (2) 8-cm hot-swap rear exhaust fans (FAN-0081)

 One (1) air shroud (CSE-PT0110)

 One (1) 3.5" fl oppy drive [FPD-PNSC-02(01)]

 Two (2) 5.25" dummy drive trays

 One (1) ATA66 cable for DVD drive (CBL-0139L)

 One (1) fl oppy cable (CBL-040L)

 One (1) front control panel cable (CBL-0087)

 One (1) I/O shield (CSE-PT55)

 SCSI Accessories (7045B-8R+ only)

One (1) dual-channel SCSI backplane (CSE-SCA-743S2)

One (1) Ultra320 SCSI ribbon cable (CBL-037L-U320)

One (1) Ultra320 SCSI round cable (CBL-0063L)

Eight (8) SCSI hot-swap drive carriers [CSE-PT17(B)]

List continued on next page.

1-1

S

UPERSERVER 7045B-8R+/7045B-TR+ User's Manual

 SATA Accessories (7045B-TR+ only)

One (1) SATA backplane (CSE-SAS-743TQ)

Six (6) SATA cables (CBL-0061L)

Two (2) SATA LED cables (CBL-0157L)

Six (6) SATA hot-swap drive carriers [CSE-PT17(B)]

 Optional:

Two (2) CPU passive heatsinks (SNK-P0018)

One (1) rackmount kit [CSE-PT026(B)]

1-2 Serverboard Features

At the heart of the SuperServer 7045B-8R+/7045B-TR+ lies the X7DB8+/X7DBE+, a

dual processor serverboard based on the Intel 5000P chipset and designed to pro-

vide maximum performance. Below are the main features of the X7DB8+/X7DBE+.

(See Figure 1-1 for a block diagram of the 5000P chipset).

Processors

The X7DB8+/X7DBE+ supports single or dual LGA 771 type Intel Xeon processors

at a FSB speed of 1066 MHz. Please refer to the serverboard description pages

on our web site for a complete listing of supported processors (www.supermicro.

com).

Memory

The X7DB8+/X7DBE+ has sixteen 240-pin DIMM slots that can support up to 64

GB of FBD (Fully Buffered DIMM) ECC DDR2-667/533 SDRAM. The memory

operates in a 4-way interleaved confi gurations and requires requires modules of

the same size and speed to be installed four at a time. See Chapter 5 Section 5

for details.

Onboard SCSI (7045B-8R+ only)

An onboard Adaptec AIC-7902 dual-channel SCSI controller in integrated into the

X7DB8+, which supports eight 80-pin SCA Ultra320 SCSI hard drives. The SCSI

drives are connected to an SCA backplane that provides power, bus termination

and confi guration settings. The SCSI drives are hot-swappable units.

Note: The operating system you use must have RAID support to enable the hot-

swap capability and RAID function of the SCSI drives.

1-2

Chapter 1: Introduction

Serial ATA

A SATA controller is integrated into the South Bridge of the 5000P chipset to

provide a six-port Serial ATA subsystem, which is RAID 0, 1, 10 and 5 supported.

The Serial ATA drives are hot-swappable units.

Note: The operating system you use must have RAID support to enable the hot-

swap capability and RAID function of the Serial ATA drives.

PCI Expansion Slots

The X7DB8+/X7DBE+ has six PCI expansion slots, which includes two x8 PCI-

Express slots, one x4 PCI-Express slot, two 64-bit 133 MHz PCI-X slots and one

64-bit 100 MHz PCI-X slot. (On the X7DB8+, one 100 MHz PCI slot supports Zero

Channel RAID.)

Onboard Controllers/Ports

One fl oppy drive controller and two onboard ATA/100 controllers are provided to

support up to four IDE hard drives or ATAPI devices. The color-coded I/O ports

include one COM port (an additional COM header is located on the serverboard), a

VGA (monitor) port, a parallel port, two USB 2.0 ports, PS/2 mouse and keyboard

ports and two gigabit Ethernet ports.

ATI Graphics Controller

The X7DB8+/X7DBE+ features an integrated ATI video controller based on the

ES1000 graphics chip. The ES1000 was designed specifi cally for servers, featuring

low power consumption, high reliability and superior longevity.

Other Features

Other onboard features that promote system health include onboard voltage moni-

tors, a chassis intrusion header, auto-switching voltage regulators, chassis and CPU

overheat sensors, virus protection and BIOS rescue.

1-3

S

UPERSERVER 7045B-8R+/7045B-TR+ User's Manual

1-3 Server Chassis Features

The following is a general outline of the main features of the SC745S2-R800/

SC745TQ-R800 server chassis.

System Power

The SC745S2-R800/SC745TQ-R800 features a redundant 800W power supply

composed of two separate power modules. This power redundancy feature allows

you to replace a failed power supply without shutting down the system.

SCSI Subsystem (7045B-8R+ only)

The SC745S2-R800 chassis was designed to support eight dual-channel SCSI

hard drives, which are hot-swappable units.

Note: The operating system you use must have RAID support to enable the hot-

swap capability of the SCSI drives.

Serial ATA Subsystem

The SC745TQ-R800 supports up to six 3 Gb/s Serial ATA drives. The Serial ATA

drives are hot-swappable units and are connected to a backplane that provides

power and control.

Note: The operating system you use must have RAID support to enable the hot-

swap capability of the Serial ATA drives.

Front Control Panel

The control panel on the SuperServer 7045B-8R+/7045B-TR+ provides you with

system monitoring and control. LEDs indicate system power, HDD activity, net-

work activity, system overheat and power supply failure. A main power button and

a system reset button are also included. In addition, two USB ports have been

incorporated into the control panel to provide front side USB access.

I/O Backplane

The SC745S2-R800/SC745TQ-R800 is an ATX form factor chassis that may be

used in either a tower or a 4U rackmount confi guration. The I/O backplane provides

six motherboard expansion slots, one COM port, a parallel port, a VGA port, two

USB 2.0 ports, PS/2 mouse and keyboard ports and two gigabit Ethernet ports.

1-4

Chapter 1: Introduction

Cooling System

The SC745S2-R800/SC745TQ-R800 chassis has an innovative cooling design that

includes three 8-cm hot-plug system cooling fans located in the middle section of

the chassis as well as two 8-cm hot-plug exhaust fans located at the rear of the

chassis. An air shroud channels the airfl ow from the system fans to effi ciently

cool the processor area of the system. The power supply module also includes

a cooling fan.

Figure 1-1. Intel 5000P Chipset:

System Block Diagram

Note: This is a general block diagram. Please see Chapter 5 for details.

Slot 6: PCI-Exp x8/SEPC

Slot 2: PCI-X

LAN Ports (2)

Slot 5: PCI-Express x8

Slot 4: PCI-Express x8

AIC

7902

PXH

Slot 1: PCI-X

Slot 3: PCI- X

82563

CPU1

PCI-Exp

x8

PCI-Exp

x8

PCI-Exp

x4

PCI-Exp

x8

PCI-X 133

Kumeran

1067/1333 MT/s

5000P

MCH

PCI -E x 8

ESB2

PCI 32

ATI

ES1000

CPU2

FBD CH0

FBD CH1

FBD CH2

FBD CH3

PCI -E x 4

3.0 Gb/s

ATA 100

USB 2.0

LPC

FB D DI MM Ban k1

DDR2

SATA Ports (6)

IDE Ports (2)

USB Ports (5)

S I/O BIOS

FB D DI MM Ban k2

FB D DI MM Ban k3

FB D DI MM Ban k4

Note: The AIC-7902 SCSI controller is only on the X7DB8+ serverboard.

Kybd/

Mouse

1-5

Floppy

COM

Ports (2)

Parallel

Port

S

UPERSERVER 7045B-8R+/7045B-TR+ User's Manual

1-4 Contacting Super Micro

Headquarters

Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)
[e-mail] (Technical Support)
Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)
[e-mail] (Technical Support)
[e-mail] (Customer Support)

Asia-Pacifi c

Address: Super Micro, Taiwan
4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [e-mail]
Tel: [phone], ext.132 or 139

1-6

Chapter 2: Server Installation

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your SuperServer 7045B-8R+/

7045B-TR+ up and running. Following these steps in the order given should enable

you to have the system operational within a minimum amount of time. This quick

setup assumes that your system has come to you with the processors and memory

preinstalled. If your system is not already fully integrated with a serverboard, pro-

cessors, system memory etc., please turn to the chapter or section noted in each

step for details on installing specifi c components.

The 7045B-8R+/7045B-TR+ may be employed either as a tower or mounted in a

rack as a 4U rackmount chassis. If using it as a tower unit, please read the Server

Precautions in the next section and then skip ahead to Section 2-5.

2-2 Unpacking the System

You should inspect the box the system was shipped in and note if it was damaged

in any way. If the server itself shows damage you should fi le a damage claim with

the carrier who delivered it.

Decide on a suitable location for the SuperServer 7045B-8R+/7045B-TR+. It should

be situated in a clean, dust-free area that is well ventilated. Avoid areas where

heat, electrical noise and electromagnetic fi elds are generated. You will also need

it placed near a grounded power outlet. Be sure to read the Rack and Server

Precautions in the next section.

2-3 Preparing for Setup

The box the system was shipped in may include two sets of rail assemblies, two

rail mounting brackets and mounting screws needed for installing the system into a

rack (optional kit). Follow the steps in the order given to complete the installation

process in a minimum amount of time. Please read this section in its entirety before

you begin the installation procedure outlined in the sections that follow.

2-1

S

UPERSERVER 7045B-8R+/7045B-TR+ User's Manual

Choosing a Setup Location

- Leave enough clearance in front of the system to enable you to open the front

door completely (~25 inches).

- Leave approximately 30 inches of clearance in the back of the system to allow for

suffi cient airfl ow and ease in servicing.

- This product is for installation only in a Restricted Access Location (dedicated

equipment rooms, service closets and the like).

- This product is not suitable for use with visual display work place devices according

to §2 of the the German Ordinance for Work with Visual Display Units.

! !

Rack Precautions

- Ensure that the leveling jacks on the bottom of the rack are fully extended to the

fl oor with the full weight of the rack resting on them.

- In single rack installation, stabilizers should be attached to the rack.

- In multiple rack installations, the racks should be coupled together.

- Always make sure the rack is stable before extending a component from the

rack.

- You should extend only one component at a time - extending two or more simul-

taneously may cause the rack to become unstable.

Warnings and Precautions!

Server Precautions

- Review the electrical and general safety precautions in Chapter 4.

- Determine the placement of each component in the rack before you install the

rails.

- Install the heaviest server components on the bottom of the rack fi rst, and then

work up.

- Use a regulating uninterruptible power supply (UPS) to protect the server from

power surges, voltage spikes and to keep your system operating in case of a power

failure.

- Allow the hot plug SCSI/SATA drives and power supply units to cool before touch-

ing them.

-

Always keep the rack's front door and all panels and components on the servers

closed when not servicing to maintain proper cooling.

2-2

Chapter 2: Server Installation

Rack Mounting Considerations

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating tempera-

ture of the rack environment may be greater than the ambient temperature of the

room. Therefore, consideration should be given to installing the equipment in an

environment compatible with the manufacturer’s maximum rated ambient tempera-

ture (Tmra).

Reduced Airfl ow

Equipment should be mounted into a rack so that the amount of airfl ow required

for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition does not

arise due to uneven mechanical loading.

Circuit Overloading

Consideration should be given to the connection of the equipment to the power

supply circuitry and the effect that any possible overloading of circuits might have

on overcurrent protection and power supply wiring. Appropriate consideration of

equipment nameplate ratings should be used when addressing this concern.

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack itself

should be grounded. Particular attention should be given to power supply connec-

tions other than the direct connections to the branch circuit (i.e. the use of power

strips, etc.).

2-3

S

UPERSERVER 7045B-8R+/7045B-TR+ User's Manual

2-4 Installing the System into a Rack

This section provides information on installing the system into a rack unit. Rack

installation requires the use of the optional rackmount kit. If the system has already

been mounted into a rack or if you are using it as a tower, you can skip ahead to

Sections 2-5 and 2-6. There are a variety of rack units on the market, which may

mean the assembly procedure will differ slightly. The following is a guideline for

installing the server into a rack with the rack rails provided in the rackmount kit.

You should also refer to the installation instructions that came with the rack unit

you are using.

Identifying the Sections of the Rack Rails

The optional rackmount kit includes two rack rail assemblies. Each of these as-

semblies consist of three sections: an inner fi xed chassis rail that secures to the

chassis, an outer rack rail that secures directly to the rack itself and two rail brackets,

which also attack to the rack (see Figure 2-1.) The inner and outer rails must be

detached from each other to install.

To remove the inner chassis rail, pull it out as far as possible - you should hear a

"click" sound as a locking tab emerges from inside the rail assembly and locks the

inner rail. Depress the locking tab to pull the inner rail completely out. Do this for

both assemblies (one for each side).

Figure 2-1. Identifying the Sections of the Rack Rails

Outer rail

Inner rail

Rail brackets

2-4

Chapter 2: Server Installation

Installing the Chassis Rails

You will need to remove the top cover and the feet to add rack rails to the chassis.

First, remove the top and right covers (top and left covers when standing as a tower

chassis) by fi rst removing the screws that secure them to the chassis. Depress

the button on the top (side if tower) of the chassis to release the cover and then

pull the cover off. Then unscrew the four feet and remove them from the chassis

(see Figure 2-2).

You can now attach rack rails to the top and bottom (now the sides) of the chassis.

First add the rack handles. Then position the inner chassis rail sections you just

removed along the side of the chassis making sure the screw holes line up. Note

that these two rails are left/right specifi c. Screw the rail securely to the side of the

chassis (see Figure 2-3). Repeat this procedure for the other rail on the other side

of the chassis. You will also need to attach the rail brackets when installing into a

telco rack.

Locking Tabs: As mentioned, the chassis rails have a locking tab, which serves

two functions. The fi rst is to lock the server into place when installed and pushed

fully into the rack, which is its normal position. Secondly, these tabs also lock the

server in place when fully extended from the rack. This prevents the server from

coming completely out of the rack when you pull it out for servicing.

Figure 2-2. Preparing to Install the Chassis Rails

2-5

S

UPERSERVER 7045B-8R+/7045B-TR+ User's Manual

Figure 2-3. Installing the Rails to the Chassis

Installing the Rack Rails

Determine where you want to place the SuperServer 7045B-8R+/7045B-TR+ in

the rack. (See Rack and Server Precautions in Section 2-3.) Position the fi xed

rack rail/sliding rail guide assemblies at the desired location in the rack, keeping

the sliding rail guide facing the inside of the rack. Screw the assembly securely

to the rack using the brackets provided. Attach the other assembly to the other

side of the rack, making sure both are at the exact same height and with the rail

guides facing inward.

2-6

Chapter 2: Server Installation

Installing the Server into the Rack

You should now have rails attached to both the chassis and the rack unit. The next

step is to install the server into the rack. You should have two brackets in the rack

mount kit. Install these fi rst keeping in mind that they are left/right specifi c (marked

with "L" and "R"). Then, line up the rear of the chassis rails with the front of the

rack rails. Slide the chassis rails into the rack rails, keeping the pressure even on

both sides (you may have to depress the locking tabs when inserting).

When the server has been pushed completely into the rack, you should hear the

locking tabs "click". Finish by inserting and tightening the thumbscrews that hold

the front of the server to the rack (see Figure 2-4).

Figure 2-4. Installing the Server into a Rack

2-7

S

UPERSERVER 7045B-8R+/7045B-TR+ User's Manual

2-5 Checking the Serverboard Setup

After setting up the the system, you will need to open the unit to make sure the

serverboard is properly installed and all the connections have been made.

1. Accessing the inside of the system (see Figure 2-5)

[If rack mounted, fi rst release the retention screws that secure the unit to the

rack. Grasp the two handles on either side and pull the unit straight out until it

locks (you will hear a "click").] There are two screws that secure the cover to

the chassis - remove these fi rst. Locate the latch on the top (side if tower) of

the chassis - depress where it says "push" then lift the latch to release the cover.

You can then lift the cover from the chassis to gain full access to the inside of

the server.

2. Check the CPUs (processors)

You may have one or two processors already installed into the serverboard. Each

processor should have its own heatsink attached. See Chapter 5 for instructions

on processor installation.

3. CPU clock ratio setting

The CPU speed should be automatically detected. No jumper or BIOS settings

need to be made.

4. Check the system memory

Your server may have come with system memory already installed. Make sure

all DIMMs are fully seated in their slots. For details on adding system memory,

refer to Chapter 5.

5. Installing add-on cards

If desired, you can install add-on cards to the system. See Chapter 5 for details

on installing PCI add-on cards.

6. Check all cable connections and airfl ow

Make sure all power and data cables are properly connected and not blocking

the chassis airfl ow. See Chapter 5 for details on cable connections.

2-8

Chapter 2: Server Installation

Figure 2-5. Accessing the Inside of the System

(Rack Confi guration shown)

2-6 Checking the Drive Bay Setup

Next, you should check to make sure the peripheral drives and the SCSI/SATA

drives and backplane have been properly installed and all connections have been

made.

1. Accessing the drive bays

All drives can be accessed from the front of the server. For servicing the CD-

ROM, IDE hard drives and fl oppy drives, you will need to remove the top/left

chassis cover. The SCSI disk drives can be installed and removed from the front

of the chassis without removing any chassis covers.

2. Installing components into the 5.25" drive bays

To install components into the 5.25" drive bays, you must fi rst remove the top/

left chassis cover as described in the previous section. Refer to Chapter 6 for

details.

3. Installing CD-ROM and fl oppy disk drives

Refer to Chapter 6 if you need to reinstall a CD-ROM and/or fl oppy disk drive

to the system.

2-9

S

UPERSERVER 7045B-8R+/7045B-TR+ User's Manual

4. Check the SCSI/SATA disk drives

Depending upon your system's confi guration, your system may have one or

more drives already installed. If you need to install SCSI or SATA drives, please

refer to Chapter 6.

5. Check the airfl ow

Airfl ow is provided by four hot-swap 8-cm chassis fans working in conjunction

with an air shroud. Two 8-cm exhaust fans are also mounted at the rear of the

chassis. The system component layout was carefully designed to promote suf-

fi cient airfl ow through the chassis. Also note that all power and data cables have

been routed in such a way that they do not block the airfl ow generated by the

fans. Keep this in mind when you reroute them after working on the system.

6. Supplying power to the system

The last thing you must do is to provide input power to the system. Plug the

power cords from the power supplies unit into a high-quality power strip that of-

fers protection from electrical noise and power surges. It is recommended that

you use an uninterruptible power supply (UPS). Finally, depress the power on

button on the front of the chassis.

2-10

Chapter 3: System Interface

Chapter 3

System Interface

3-1 Overview

The control panel on the 7045B-8R+/7045B-TR+ has several LEDs and two buttons.

There are also two LEDs on each SCSI drive carrier (7045B-8R+) and SATA drive

carrier (7045B-TR+). These LEDs keep you constantly informed of the overall status

of the system and the activity and health of specifi c components.

3-2 Control Panel Buttons

There are two push-buttons located on the front of the chassis. These are (in order

from left to right) a power on/off button and a reset button.

 POWER: This is the main power button, which is used to apply or turn off

the main system power. Turning off system power with this button removes the

main power but keeps standby power supplied to the system.

 RESET:

Use the reset button to reboot the system.

3-1

S

UPERSERVER 7045B-8R+/7045B-TR+ User's Manual

3-3 Control Panel LEDs

The control panel located on the front of the SC745S2-R800/SC745TQ-R800 chas-

sis has six LEDs that provide you with critical information related to different parts

of the system. This section explains what each LED indicates when illuminated

and any corrective action you may need to take.

 Power:

LED should normally be on when the system is operating.

 HDD: Indicates IDE channel activity. On the 7045B-8R+/7045B-TR+, this

LED indicates SCSI/SATA drive activity when fl ashing.

 NIC1:

Indicates power is being supplied to the system's power supply. This

1

Indicates network activity on JLAN1 when fl ashing.

2

 NIC2: Indicates network activity on JLAN2 when fl ashing.

 Overheat/Fan Fail: When this LED fl ashes, it indicates a fan failure. When

on continuously it indicates an overheat condition, which may be caused by cables

obstructing the airfl ow in the system or the ambient room temperature being too

warm. Check the routing of the cables and make sure all fans are present and

operating normally. You should also check to make sure that the chassis covers

are installed. Finally, verify that the heatsinks are installed properly (see Chapter

5). This LED will remain fl ashing or on as long as the indicated condition exists.

3-2

Chapter 3: System Interface

 Power Fail: Indicates a power supply module has failed. This should be

accompanied by an audible alarm. A backup power supply module will take the

load and keep the system running but the failed module will need to be replaced.

Refer to Chapter 6 for details on replacing the power supply. This LED should be

off when the system is operating normally.

3-4 Drive Carrier LEDs

SCSI Drives (7045B-8R+)

Each SCSI drive carrier has two LEDs.

 Green: When illuminated, the green LED on the front of the SCSI drive car-

rier indicates drive activity. A connection to the SCSI SCA backplane enables this

LED to blink on and off when that particular drive is being accessed.

 Red: The SAF-TE compliant backplane activates the red LED to indicate a

drive failure. If one of the SCSI drives fail, you should be notifi ed by your system

management software. Please refer to Chapter 6 for instructions on replacing failed

SCSI drives.

SATA Drives (7045B-TR+)



Green: Each Serial ATA drive carrier has a green LED. When illuminated,

this green LED (on the front of the SATA drive carrier) indicates drive activity. A

connection to the SATA backplane enables this LED to blink on and off when that

particular drive is being accessed. Please refer to Chapter 6 for instructions on

replacing failed SATA drives.

 Red: The red LED to indicate an SATA drive failure. If one of the SATA drives

fail, you should be notifi ed by your system management software. Please refer to

Chapter 6 for instructions on replacing failed SATA drives.

3-3

S

UPERSERVER 7045B-8R+/7045B-TR+ User's Manual

Notes

3-4