Supero SUPERSERVER 6113L-8, SUPERSERVER 6113L-i User Manual

®

SUPERSERVER 61 13L-8

SUPERSERVER 61 13L-i

USER’S MANUAL

1.0

SUPER

The information in this User’s Manual has been carefully reviewed and is believed to be
accurate. The vendor assumes no responsibility for any inaccuracies that may be
contained in this document, makes no commitment to update or to keep current the
information in this manual, or to notify any person or organization of the updates.

Please
Note: For the most up-to-date version of this manual, please see our
web site at www.supermicro.com.

SUPERMICRO COMPUTER reserves the right to make changes to the product described in
this manual at any time and without notice. This product, including software, if any, and
documentation may not, in whole or in part, be copied, photocopied, reproduced, translated
or reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM
THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR
SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED
OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING,
INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR
DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of
Santa Clara shall be the exclusive venue for the resolution of any such disputes.
Supermicro's total liability for all claims will not exceed the price paid for the hardware
product.

Unless you request and receive written permission from SUPER MICRO COMPUTER,
you may not copy any part of this document.

Information in this document is subject to change without notice. Other products and
companies referred to herein are trademarks or registered trademarks of their respective
companies or mark holders.

Copyright © 2004 by SUPER MICRO COMPUTER INC.
All rights reserved.

Printed in the United States of America

Preface

About This Manual

This manual is written for professional system integrators and PC technicians.
It provides information for the installation and use of the SuperServer 6113L-8/
6113L-i. Installation and maintainance should be performed by experienced
technicians only.

The SuperServer 6113L-8/6113L-i is a high-end, dual Itanium2 processor
rackmount server based on the SC813HS-500/SC813Hi-500 1U rackmount server
chassis and the i2DML-8G2/i2DML-iG2 serverboard.

Manual Organization

Chapter 1: Introduction

The first chapter provides a checklist of the main components included with the
server system and describes the main features of the SUPER i2DML-8G2/i2DML­iG2 serverboard and the SC813HS-500/SC813Hi-500 chassis.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer 6113L-8/
6113L-i into a rack and check out the server configuration prior to powering up
the system. If your server was ordered without processor and memory compo­nents, this chapter will refer you to the appropriate sections of the manual for
their installation.

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.

Chapter 4: System Safety

You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 6113L-8/6113L-i.

iii

Preface

SUPERSERVER 6113L-8/6113L-i User's Manual

iv

Chapter 5: Advanced Serverboard Setup

Chapter 5 provides detailed information on the i2DML-8G2/i2DML-iG2
serverboard, including the locations and functions of connectors, headers and
jumpers. Refer to this chapter when adding or removing processors or main
memory and when reconfiguring the serverboard.

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the 1U SC813HS-500/SC813Hi-500
rackmount server chassis. You should follow the procedures given in this chapter
when installing, removing or reconfiguring SCSI/IDE or peripheral drives and when
replacing the system power supply unit and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed infor­mation on running the CMOS Setup Utility.

Appendix A: BIOS Error Beep Codes

Appendix B: BIOS POST Codes

Appendix C: Software Installation

Appendix D: System Specifications

v

Preface

Notes

SUPERSERVER 6113L-8/6113L-i User's Manual

vi

Table of Contents

Preface

About This Manual ....................................................................................................... ii i

Manual Organization .................................................................................................... ii i

Chapter 1: Introduction

1-1 Overview ............................................................................................................ 1- 1

1-2 Serverboard Features ...................................................................................... 1-2

1- 3 Server Chassis Features ................................................................................ 1 -5

1- 4 Contacting Supermicro ................................................................................... 1 -7

Chapter 2: Server Installation

2-1 Overview ............................................................................................................ 2- 1

2-2 Unpacking the SuperServer 6113L-8/6113L-i................................................ 2 -1

2- 3 Preparing for Setup ......................................................................................... 2-1

Choosing a Setup Location...................................................................... 2-2

Rack Precautions...................................................................................... 2- 2

Server Precautions.................................................................................... 2-2

2-4 Installing the Server into a Rack ................................................................... 2-3

Identifying the Sections of the Rack Rails ............................................ 2-3

Installing the Outer Rails ...........................................................................2-3

Installing the Server into the Rack ...........................................................2-4

Installing the Server into a Telco Rack ....................................................2-6

2- 5 Checking the Serverboard Setup ................................................................... 2 -7

2-6 Checking the Drive Bay Setup....................................................................... 2 -9

Chapter 3: System Interface

3-1 Overview ............................................................................................................ 3- 1

3-2 Control Panel Buttons..................................................................................... 3- 1

Reset.......................................................................................................... 3-1

Power ......................................................................................................... 3 -1

3- 3 Control Panel LEDs......................................................................................... 3-2

Overheat ..................................................................................................... 3 -2

NIC2 ............................................................................................................ 3- 2

NIC1 ............................................................................................................ 3- 2

HDD ............................................................................................................ 3-2

Power ......................................................................................................... 3 -3

3- 4 SCSI Drive Carrier LEDs................................................................................. 3 -3

Chapter 4: System Safety

4-1 Electrical Safety Precautions...........................................................................4-1

4- 2 General Safety Precautions .............................................................................4-2

4-3 ESD Precautions ...............................................................................................4-3

4- 4 Operating Precautions ......................................................................................4-4

Chapter 5: Advanced Serverboard Setup

5-1 Handling the i2DML-8G2/i2DML-iG2 Serverboard........................................... 5-1

5-2 Itanium2 Processor and Heatsink Installation ................................................5-2

5- 3 Connecting Cables ............................................................................................5-9

Connecting Data Cables ............................................................................5-9

Connecting Power Cables ..........................................................................5-9

Connecting the Control Panel .................................................................5-10

5-4 I/O Ports ...........................................................................................................5-11

5- 5 Installing Memory ............................................................................................5-11

5- 6 Adding PCI Cards............................................................................................5-13

5-7 Serverboard Details ....................................................................................... 5-14

i2DML-8G2 Layout .................................................................................. 5-14

i2DML-8G2/i2DML-iG2 Quick Reference .............................................. 5-15

5- 8 Connector Definitions .................................................................................... 5-16

EPS 12V Power Connector.................................................................... 5-16

Processor Power Connectors ................................................................ 5-16

Power Fail LED ....................................................................................... 5-16

NMI Button............................................................................................... 5-16

Power LED............................................................................................... 5-16

HDD LED ................................................................................................. 5-17

NIC1 LED ................................................................................................. 5-17

NIC2 LED ................................................................................................. 5-17

Overheat LED .......................................................................................... 5-17

Reset Button ........................................................................................... 5-18

Power Button........................................................................................... 5-18

Universal Serial Bus ............................................................................... 5-18

Front Panel USB Headers ..................................................................... 5-19

Serial Ports ............................................................................................. 5-19

GLAN 1/2 (Ethernet Ports) .................................................................... 5-19

Chassis Intrusion .................................................................................... 5-19

Fan Headers ............................................................................................ 5-20

Power Fault ............................................................................................. 5-20

Wake-on-Ring .......................................................................................... 5-20

vii

Table of Contents

SUPERSERVER 6113L-8/6113L-i User's Manual

viii

SMB ......................................................................................................... 5-21

SMB Power Connector ........................................................................... 5-21

5- 9 Jumper Settings............................................................................................. 5-22

Explanation of Jumpers.......................................................................... 5-22

CMOS Clear ............................................................................................ 5-22

VGA Enable/Disable ............................................................................... 5-22

GLAN Enable/Disable............................................................................. 5-23

Watch Dog Enable/Disable.................................................................... 5-23

Power Fail Alarm Enable/Disable ......................................................... 5-23

SCSI Enable/Disable .............................................................................. 5-24

5-10 Onboard Indicators ........................................................................................ 5-24

GLAN LEDs ............................................................................................. 5-24

Debug LEDs ............................................................................................ 5-24

SCSI Activity LED................................................................................... 5-25

5-11 SCSI and IDE Disk Drive Connections ....................................................... 5-25

IDE Connectors ....................................................................................... 5-25

Ultra320 SCSI Connectors ..................................................................... 5-26

Chapter 6: Advanced Chassis Setup

6- 1 Static-Sensitive Devices ................................................................................. 6- 1

6- 2 Control Panel ................................................................................................... 6- 2

6-3 System Fans .................................................................................................... 6- 3

System Fan Failure .................................................................................. 6-3

Replacing System Cooling Fans............................................................. 6-3

6-4 Drive Bay Installation/Removal ....................................................................... 6-4

Removing the Front Bezel ....................................................................... 6-4

Accessing the Drive Bays ....................................................................... 6-5

SCSI/IDE Drive Installation ...................................................................... 6 -6

CD-ROM Drive Installation ....................................................................... 6-8

6- 5 Power Supply................................................................................................... 6- 9

Power Supply Failure ............................................................................... 6 -9

Removing/Replacing the Power Supply .................................................. 6-9

Chapter 7: BIOS

7-1 Introduction.........................................................................................................7-1

7-2 Main Setup Screen ...........................................................................................7-2

7- 3 Advanced Setup Screen ...................................................................................7-3

7-4 PCI/PnP Configuration ....................................................................................7-11

7-5 Security settings .............................................................................................7-12

7-6 Exit Options .....................................................................................................7-13

Table of Contents

ix

Appendices:

Appendix A: BIOS Error Beep Codes...................................................................... A-1

Appendix B: BIOS POST Codes .............................................................................. B-1

Appendix C: Software Installation ............................................................................ C-1

Appendix D: System Specifications ........................................................................ D-1

SUPERSERVER 6113L-8/6113L-i User's Manual

x

Notes

Chapter 1

Introduction

1-1 Overview

The Supermicro SuperServer 6113L-8/6113L-i is a high-end dual processor, 1U
rackmount server that features some of the most advanced technology currently
available. The SuperServer 6113L-8/6113L-i is comprised of two main sub­systems: the SC813HS-500/SC813Hi-500 1U rackmount chassis and the i2DML­8G2/i2DML-iG2 dual Itanium2 processor serverboard. Please refer to our web
site for information on operating systems that have been certified for use with the
SuperServer 6113L-8/6113L-i (www.supermicro.com).

In addition to the mainboard and chassis, various hardware components may
have been included with your SuperServer 6113L-8/6113L-i, as listed below:

! Two (2) 1U Itanium2 CPU heatsinks (SNK-0046)

! One (1) heatsink retention socket with hex key (SKT-0147-RM-IT2)

! Two (2) power pods: Itanium2 voltage regulator modules (VRM-0008)

! One (1) slim CD-ROM drive (CDM-TEAC-24(B))

! One (1) riser card (CSE-RR1U-X)

! Four (4) Ultra320 SCSI drive carriers (CSE-PT-39(B), 6113L-8 only)

! Four (4) IDE drive carriers (CSE-PT-42(B), 6113L-i only)

! One (1) front access USB and COM port tray (CSE-PT40(B))

! Rackmount hardware (with screws):

Two (2) rack rail assemblies

Six (6) brackets for mounting the rack rails to a rack/telco rack

! One (1) CD-ROM containing drivers and utilities

! SuperServer 6113L-8/6113L-i User's Manual

Chapter 1: Introduction

1-1

SUPERSERVER 6113L-8/6113L-i User's Manual

1-2

1-2 Serverboard Features

At the heart of the SuperServer 6113L-8/6113L-i lies the i2DML-8G2/i2DML-iG2,
a dual Intel Itanium2 processor serverboard designed to provide maximum perfor­mance. Below are the main features of the i2DML-8G2/i2DML-iG2.

Chipset

The i2DML-8G2/i2DML-iG2 is based on Intel's E8870 chipset, which is a high­performance chipset designed for high-end server platforms (see Figure 1-1).

The Intel 8870 chipset consists of the four primary components: the Scalable Node
Controller (SNC), the Server I/O Hub (SIOH), the DDR Memory Hub (DMH), and the
Scalability Port Switch (SPS). Complementary components include the I/O Hub
Controller (Intel ICH4), the Firmware Hub (FWH), and the PCI Bus Bridge (P64H2).

The SNC is the main component in the processor/memory subsystem. It con­nects to four DDR memory hubs through four separate links to provide a peak
memory bandwidth of 6.4 GB/s. Each DDR Memory Hub connects to two branch
channels and supports up to four DDR SDRAM DIMMs per channel. The
Scalability Port (SP) provides simultaneous, bi-directional signaling with an ag­gregate bandwidth of 6.4 GB/sec per port. Two SP ports per SNC provide a
maximum bandwidth capability of 12.8 GB/s. The SNC delivers balanced, high­bandwidth throughput across the processors, memory and I/O.

The SIOH is the central component of the I/O subsystem and provides the
connection between four Hub Interface 2.0 ports and two Scalability Ports. The
the SIOH with four Hub Interfaces has a aggregate peak bandwidth of 4 GB/sec.
The SIOH also offers a Hub Interface 1.5 connection to legacy I/O and firmware
via the I/O Controller Hub (ICH4).

The DMH is a bridge for data transfers between the SNC and the two DDR
memory channels. Each DMH has a maximum throughput of 1.6 GB/s and sup­ports up to eight single or double density registered DIMMs.

The SPS is not used in the i2DML-8G2/i2DML-iG2.

Note: "(B)" indicates black.

1-3

Chapter 1: Introduction

Processors

The i2DML-8G2/i2DML-iG2 supports single or dual Intel Itanium2 processors of
up to 1.50 GHz with a 6 MB L3 cache at a 400 MHz FSB. Please refer to the
support section of our web site for a complete listing of supported processors
(http://www.supermicro.com/support/).

Memory

The i2DML-8G2/i2DML-iG2 has eight 184-pin, DIMM slots that can support up to
16 GB of low-profile, registered ECC DDR200 (PC1600) SDRAM (DDR266 is
supported but at 200 MHz only). Module sizes of 128 MB, 256 MB, 512 MB, 1
GB and 2 GB may be used to populate the DIMM slots. (This serverboard has
has been designed to support 2GB DIMM modules for each memory slot, but it has
only been validated with 1GB memory modules.)

PCI Expansion Slots

The i2DML-8G2/i2DML-iG2 has one 64-bit, 133/100 MHz PCI-X slot available for
use in a 1U server configuration. A riser card is included with the server. This
riser card fits into a PCI-X slot on the serverboard and was designed specially for
the SC813HS-500/SC813Hi-500 chassis to support the use of one standard (full­length) PCI-X card.

ATI Graphics Controller

The i2DML-8G2/i2DML-iG2 features an integrated ATI video controller based on
the Rage XL graphics chip. Rage XL fully supports sideband addressing and AGP
texturing. This onboard graphics package can provide a bandwidth of up to 512
MB/sec over a 32-bit graphics memory bus.

Onboard Controllers/Ports

The i2DML-8G2 (only) includes an onboard LSI Ultra320 SCSI controller for dual­channel operation. Backpanel I/O ports on the 6113L-8/6113L-i include two COM
ports, two USB ports and a VGA (monitor) port. An Intel 82546EB Ethernet
controller provides support for two Gb LAN ports, which are also located on the
backpanel.

SUPERSERVER 6113L-8/6113L-i User's Manual

1-4

Figure 1-1. E8870 Chipset Block Diagram

Other Features

Other onboard features are included to promote system health. These include
various voltage monitors, two CPU temperature sensors, four fan speed sensors,
a chassis intrusion header, auto-switching voltage regulators, chassis and CPU
overheat sensors, virus protection and BIOS rescue.

SNC

Processor 1 Processor 2

ICH4

16 GB (Max.) DDR200

3x1MB

FWH

MRH_D
MRH_D

DIMM1
DIMM5

DIMM2
DIMM6

LPC Bus

SIOH

P64H2

IDE1

Hublink0

VGA

PCI 32

USB0/1/2/

3/4/5/6

USB 2.0

IPMI

3x1MB

FWH

LPC

Super

I/O

LPC Bus

COM1/2

PCI-X 133

82546EB

GLAN

Cntrl

PCI-X 100

PCI Slot

IDE2

UDMA100

Riser C ard

Hublink0

MRH_D
MRH_D

DIMM3
DIMM7
DIMM4
DIMM8

LSI U320

SCSI Cntrl

Note: This is a general block diagram. Please see the previous Serverboard

Features pages for details on the features of each serverboard.

1-5

Chapter 1: Introduction

1-3 Server Chassis Features

The SC813HS-500/SC813Hi-500 is one of Supermicro's third-generation 1U chas­sis and features four SCSI/IDE hard drive bays, a slim CD-ROM drive and a
revolutionary cooling design that can keep today's most powerful processors
running well below their temperature thresholds. The following is a general
outline of the main features of the SC813HS/SC813Hi-500 chassis.

System Power

When configured as a SuperServer 6113L-8/6113L-i, the SC813HS-500/SC813Hi­500 chassis includes a 500W cold-swap power supply.

Control Panel

The SC813HS-500/SC813Hi-500 control panel provides important system moni­toring and control information. LEDs indicate power on, network activity, hard
disk drive activity and system overheat conditions. Also present are a main
power button and a system reset button.

I/O Backplane

The SC813HS-500/SC813Hi-500 is a 1U rackmount chassis. Its I/O backplane
provides one full-length PCI-X slot, a COM port (another COM port is an onboard
header located near the USB2/3 ports), one VGA port, two USB ports and two
Ethernet (LAN) ports. (See Figure 1-2.)

Figure 1-2. I/O Backplane

Ethernet PortsCOM1 Port

VGA Port

USB Ports

PCI-X Slot

External SCSI Port

(6113L-8 only)

SUPERSERVER 6113L-8/6113L-i User's Manual

1-6

Cooling System

The SC813HS-500/SC813Hi-500 chassis' revolutionary cooling design has been
optimized to provide sufficient cooling for dual Itanium2 configurations. The
SC813HS-500/SC813Hi-500 includes two heavy duty 10-cm blower fans located
in the middle of the chassis. These fans operate continuously at full rpm. If they
break down, the ambient air temperature inside the chassis will rise and activate
an overheat LED. In addition, a high-speed 4-cm fan is also included to increase
the flow of cooling air through the system.

1-7

Chapter 1: Introduction

1-4 Contacting Supermicro

Headquarters

Address: SuperMicro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)
Web Site: www.supermicro.com

Europe

Address: SuperMicro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Asia-Pacific

Address: SuperMicro, Taiwan

D5, 4F, No. 16 Chien-Ba Road

Chung-Ho 235, Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [e-mail]
Tel: [phone], ext.132 or 139

SUPERSERVER 6113L-8/6113L-i User's Manual

1-8

Notes

Chapter 2: Server Installation

2-1

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your SuperServer 6113L-8/
6113L-i up and running. Following these steps in the order given should enable
you to have the system operational within a minimum amount of time. This quick
setup assumes that your SuperServer 6113L-8/6113L-i system has come to you
with the processors and memory preinstalled. If your system is not already fully
integrated with a serverboard, processors, system memory etc., please turn to
the chapter or section noted in each step for details on installing specific com­ponents.

2-2 Unpacking the SuperServer 6113L-8/6113L-i

You should inspect the box the SuperServer 6113L-8/6113L-i was shipped in and
note if it was damaged in any way. If the server itself shows damage you should
file a damage claim with the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the SuperServer
6113L-8/6113L-i. It should be situated in a clean, dust-free area that is well
ventilated. Avoid areas where heat, electrical noise and electromagnetic fields
are generated. You will also need it placed near a grounded power outlet. Be
sure to read the Rack and Server Precautions in the next section.

2-3 Preparing for Setup

The box the SuperServer 6113L-8/6113L-i was shipped in should include two sets
of rail assemblies, six (four front and two rear) rail mounting brackets and screws
you will need to install the system into the rack. Follow the steps in the order
given to complete the installation process in a minimum amount of time. Please
read this section in its entirety before you begin the installation procedure out­lined in the sections that follow.

SUPERSERVER 6113L-8/6113L-i User's Manual

2-2

Choosing a Setup Location

- Leave enough clearance in front of the rack to enable you to open

the front door completely (~25 inches).

- Leave approximately 30 inches of clearance in the back of the rack

to allow for sufficient airflow and ease in servicing.

Rack Precautions

- Ensure that the leveling jacks on the bottom of the rack are fully

extended to the floor with the full weight of the rack resting on them.

- In single rack installation, stabilizers should be attached to the rack.

- In multiple rack installations, the racks should be coupled together.

- Always make sure the rack is stable before extending a component

from the rack.

- You should extend only one component at a time - extending two or

more simultaneously may cause the rack to become unstable.

Server Precautions

- Review the electrical and general safety precautions in Chapter 4.

- Determine the placement of each component in the rack before you

install the rails.

- Install the heaviest server components on the bottom of the rack

first, and then work up.

- Use a regulating uninterruptible power supply (UPS) to protect the
server from power surges, voltage spikes and to keep your
system operating in case of a power failure.

- Allow the power supply units to cool before touching them.

- Always keep the rack's front door and all panels and components on

the servers closed when not servicing to maintain proper cooling.

!

!

Warnings and Precautions!

2-3

Chapter 2: Server Installation

2-4 Installing the Server into a Rack

This section provides information on installing the SuperServer 6113L-8/6113L-i
into a rack unit with the rack rails provided. If the 6113L-8/6113L-i has already
been mounted into a rack, you can skip ahead to Sections 2-5 and 2-6. There
are a variety of rack units on the market, which may mean the assembly proce­dure will differ slightly. You should also refer to the installation instructions that
came with the rack unit you are using.

Identifying the Sections of the Rack Rails

You should have received two rack rail assemblies with the SuperServer 6113L­8/6113L-i. Each of these assemblies consists of two sections: an inner fixed
chassis rail that secures to the 6113L-8/6113L-i and an outer fixed rack rail
that secures directly to the rack itself. A pair of short brackets to be used
on the front side of the outer rails are also included.

Installing the Outer Rails

Begin by measuring the distance from the front rail to the rear rail of the rack.
Attach a short bracket to the front side of the right outer rail and a long bracket
to the rear side of the right outer rail. Adjust both the short and long brackets
to the proper distance so that the rail can fit snugly into the rack. Secure the
short bracket to the front side of the outer rail with two M4 screws and the long
bracket to the rear side of the outer rail with three M4 screws. Repeat these
steps for the left outer rail.

Locking Tabs: Both chassis rails have a locking tab, which serves two functions.
The first is to lock the server into place when installed and pushed fully into the
rack, which is its normal position. Secondly, these tabs also lock the server in
place when fully extended from the rack. This prevents the server from coming
completely out of the rack when you pull it out for servicing.

SUPERSERVER 6113L-8/6113L-i User's Manual

2-4

Figure 2-1. Installing the Rack Rails

Installing the Server into the Rack

You should now have rails attached to both the chassis and the rack
unit. The next step is to install the server into the rack. Do this by
lining up the rear of the chassis rails with the front of the rack rails.
Slide the chassis rails into the rack rails, keeping the pressure even on
both sides (you may have to depress the locking tabs when inserting).
See Figure 2-2.

When the server has been pushed completely into the rack, you should hear the
locking tabs "click". Finish by inserting and tightening the thumbscrews that
hold the front of the server to the rack.

2-5

Chapter 2: Server Installation

Figure 2-2. Installing the Server into a Rack

(front bezel is optional)

SUPERSERVER 6113L-8/6113L-i User's Manual

2-6

Figure 2-3. Installing the Server into a Telco Rack

(front bezel is optional)

Installing the Server into a Telco Rack

If you are installing the SuperServer 6113L-86113L-8/6113L-i into a Telco type
rack, follow the directions given on the previous pages for rack installation. The
only difference in the installation procedure will be the positioning of the rack
brackets to the rack. They should be spaced apart just enough to accommodate
the width of the telco rack.

2-7

Chapter 2: Server Installation

2-5 Checking the Serverboard Setup

After you install the 6113L-8/6113L-i in the rack, you will need to open
the unit to make sure the serverboard is properly installed and all the connections
have been made.

1. Accessing the inside of the 6113L-8/6113L-i (see Figure 2-4):

First, release the retention screws that secure the unit to the rack. Grasp the
two handles on either side and pull the unit straight out until it locks (you will
hear a "click"). Next, depress the two buttons on the top of the chassis to
release the top cover. There is a large rectangular recess in the middle front
of the top cover to help you push the cover away from you until it stops. You
can then lift the top cover from the chassis to gain full access to the inside
of the server.

2. Check the CPUs (processors):

You may have one or two processors already installed into the serverboard.
Each processor needs its own heatsink and power pod (VRM) installed. See
Chapter 5 for instructions on processor and heatsink installation.

3. Verify the proper CPU clock ratio setting:

If the CPU speed is not automatically detected you may need to set the
correct speed with the BIOS Setup utility. See the appropriate setting in BIOS
(Chapter 7) for setting the proper CPU speed. (Most processor speeds are
automatically detected so this step should be unnecessary.)

4. Check the system memory:

Your 6113L-8/6113L-i server system may have come with system memory
already installed. Make sure all DIMMs are fully seated in their slots. For
details on adding system memory, refer to Chapter 5.

5. Installing add-on cards:

If desired, you can install add-on cards to the system. See Chapter 5 for
details on installing PCI add-on cards.

SUPERSERVER 6113L-8/6113L-i User's Manual

2-8

Figure 2-4. Accessing the Inside of the SuperServer 6113L-8/6113L-i

6. Check all cable connections and airflow:

Make sure all power and data cables are properly connected and not blocking
the chassis airflow. See Chapter 5 for details on cable connections. Also,
check the air seals for damage. The air seals are located under the blower
fan and beneath the frame cross section that separates the drive bay area from
the serverboard area of the chassis.

2-9

Chapter 2: Server Installation

2-6 Checking the Drive Bay Setup

Next, you should check to make sure the peripheral drives and the SCSI/IDE
drives have been properly installed and all connections have been made.

1. Accessing the drive bays:

All drives are accessable from the front of the server. For servicing the CD­ROM and IDE drives, you will need to remove the top chassis cover (not
necessary for SCSI drives). See Chapter 6 for details.

2. CD-ROM drive:

A slim CD-ROM drive should be preinstalled in your server. Refer to Chapter
6 if you need to reinstall a CD-ROM drive to the system.

3. Check the SCSI/IDE disk drives:

Depending upon your system's configuration, your system may have one or
more SCSI (6113L-8) or IDE (6113L-i) drives already installed. If you need to
install SCSI/IDE drives, please refer to Chapter 6.

4. Check the airflow:

Airflow is provided by two heavy duty 10-cm blower fans and one high-speed
4-cm fan. The system component layout was carefully designed to direct
sufficient cooling airflow to the components that generate the most heat. Note
that all power and data cables have been routed in such a way that they do
not block the airflow generated by the fans.

5. Supplying power to the system:

The last thing you must do is to provide input power to the system. Plug the
power cord from the power supply unit into a high-quality power strip that offers
protection from electrical noise and power surges. It is recommended that you
use an uninterruptible power supply (UPS).

SUPERSERVER 6113L-8/6113L-i User's Manual

2-10

Notes

Chapter 3: System Interface

3-1

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the chassis control panel to keep you constantly
informed of the overall status of the system as well as the activity and health of
specific components. There are also two buttons on the chassis control panel
and an on/off switch on the power supply. This chapter explains the meanings

of all LED indicators and the appropriate response you may need to take.

3-2 Control Panel Buttons

There are two push-button buttons located on the front of the chassis. These are
(in order from left to right) a reset button and a power on/off button.

! RESET: The reset switch reboots the system.

! POWER: This is the main power switch, which is used to apply or turn off

the main system power. Turning off system power with this button removes the
main power but keeps standby power supplied to the system.

RESET

SUPERSERVER 6113L-8/6113L-i User's Manual

3-2

3-3 Control Panel LEDs

The control panel located on the front of th SC813HS-500/SC813Hi-500 chassis
has four LEDs. These LEDs provide you with critical information related to
different parts of the system. This section explains what each LED indicates
when illuminated and any corrective action you may need to take.

! OVERHEAT: Indicates an overheat condition in the chassis. This may be
caused by cables obstructing the airflow in the system, or the ambient room
temperature being too warm. You should also check to make sure that the
chassis cover is installed and that all fans are present and operating normally.
Finally, check the air seals for damage. The air seals are located under the
blower fan and beneath the frame cross section that separates the drive bay area
from the serverboard area of the chassis.

! NIC2: Indicates network activity on GLAN2 when flashing .

! NIC1: Indicates network activity on GLAN1 when flashing.

! HDD: Indicates SCSI/IDE channel activity. On the SuperServer 6113L-8/

6113L-i this light indicates SCSI/IDE and/or CD-ROM drive activity when flashing.

NIC2

NIC1