Supero SUPERSERVER 6017TR-TQF, SUPERSERVER 6017TR-TFF, SUPERSERVER 6017TR-TF User Manual

®

SUPER

User's Manual

Revision 1.0

SUPERSERVER
6017TR-TQF
6017TR-TFF
6017TR-TF

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at

www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTW ARE, OR DA TA ST ORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See

www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.

Manual Revision 1.0
Release Date: November 29, 2012

Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.

Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2012 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

iii

Preface

Preface

About This Manual

This manual is written for professional system integrators and PC technicians.
It provides information for the installation and use of the SuperServer
6017TR-TQF/TFF/TF. Installation and maintainance should be performed by
experienced technicians only.

The SuperServer 6017TR-TQF/TFF/TF is a high-end server based on the SC808BT­1K28B 1U rackmount chassis and the dual processor X9DRT-IBQF/IBFF/F
serverboard. All models have an IPMI LAN port and two serverboard nodes with
two hot-swap 3.5" SATA3 Hard Disk Drives (HDD) each per node.

Each of the various models of the SuperServer 6017TR-TQF/TFF/TF servers and
their associated serverboards for each of their unique options are listed in the
table below:

SUPERSERVER 6017TR-TQF/TFF/TF Model Variations

Server

Model

X9DRT

Serverboard

Infi niBand

QDR

Infi niBand

FDR

6017TR-TQF

X9DRT-IBQF YES

6017TR-TFF

X9DRT-IBFF YES

6017TR-TF

X9DRT-F

Manual Organization

Chapter 1: Introduction

The fi rst chapter provides a checklist of the main components included with
the server system and describes the main features of the X9DRT-IBQF/IBFF/F
serverboard and the SC808BT-1K28B chassis.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer
6017TR-TQF/TFF/TF into a rack and check out the server confi guration prior to
powering up the system. If your server was ordered without processor and memory
components, this chapter will refer you to the appropriate sections of the manual
for their installation.

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

iv

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.

Chapter 4: System Safety

You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SUPERSERVER 6017TR-TQF/TFF/TF.

Chapter 5: Advanced Serverboard Setup

Chapter 5 provides detailed information on the X9DRT-IBQF/IBFF/F serverboard,
including the locations and functions of connections, headers and jumpers. Refer
to this chapter when adding or removing processors or main memory and when
reconfi guring the serverboard.

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the SC808BT-1K28BP server chassis.
You should follow the procedures given in this chapter when installing, removing or
reconfi guring SATA or peripheral drives and when replacing system power supply
units and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed information
on running the CMOS Setup Utility.

Appendix A: BIOS Error Beep Codes
Appendix B: System Specifi cations

v

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Notes

vi

Table of Contents

Chapter 1 Introduction

1-1 Overview .........................................................................................................1-1

1-2 Serverboard Features .....................................................................................1-2

Processors ......................................................................................................1-2

Memory ...........................................................................................................1-2

Serial ATA ....................................................................................................... 1-2

PCI Expansion Slots .......................................................................................1-2

Onboard Controllers/Ports .............................................................................. 1-3

Graphics Controller .........................................................................................1-3

Infi niBand ........................................................................................................ 1-3

Other Features ................................................................................................ 1-3

1-3 Server Chassis Features ................................................................................ 1-4

System Power ................................................................................................. 1-4

SATA Subsystem ............................................................................................. 1-4

Front Control Panel ......................................................................................... 1-4

I/O Ports ..........................................................................................................1-4

Cooling System ............................................................................................... 1-5

Air Shrouds ..................................................................................................... 1-5

Mounting Rails ................................................................................................ 1-5

1-4 Advanced Power Management ....................................................................... 1-5

Intel® Intelligent Power Node Manager (NM) .................................................1-5

Manageability Engine (ME) ............................................................................. 1-5

1-5 Contacting Supermicro ....................................................................................1-7

1-6 2U Twin

2

: System Notes ................................................................................. 1-8

Nodes ..............................................................................................................1-8

System Power ................................................................................................. 1-8

SATA Backplane/Drives ...................................................................................1-8

Chapter 2 Server Installation

2-1 Overview .........................................................................................................2-1

2-2 Unpacking the System .................................................................................... 2-1

2-3 Preparing for Setup ......................................................................................... 2-1

2-4 Cautions! .........................................................................................................2-2

Choosing a Setup Location .............................................................................2-2

Rack Precautions ............................................................................................ 2-2

Server Precautions ..........................................................................................2-2

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

vii

Rack Mounting Considerations ....................................................................... 2-3

Ambient Operating Temperature ................................................................ 2-3

Reduced Airfl ow ......................................................................................... 2-3

Mechanical Loading ................................................................................... 2-3

Circuit Overloading ..................................................................................... 2-3

Reliable Ground ......................................................................................... 2-3

2-5 Installing the System into a Rack ...................................................................2-4

Identifying the Sections of the Rack Rails ...................................................... 2-4

Installing the Inner Rail Extension ..................................................................2-5

Outer Rack Rails ............................................................................................. 2-6

2-6 Checking the Serverboard Setup ....................................................................2-8

2-7 Checking the Drive Bay Setup ........................................................................2-9

Chapter 3 System Interface

3-1 Overview .........................................................................................................3-1

3-2 Control Panel Button ......................................................................................3-2

3-3 Control Panel LEDs ........................................................................................ 3-2

3-4 Drive Carrier LEDs .......................................................................................... 3-3

SATA Drives ....................................................................................................3-3

SAS Drives ...................................................................................................... 3-4

Chapter 4 Standardized Warning Statements for AC Systems

4-1 About Standardized Warning Statements ....................................................... 4-1

Warning Defi nition ...........................................................................................4-1

Installation Instructions ....................................................................................4-4

Circuit Breaker ................................................................................................ 4-5

Power Disconnection Warning ........................................................................ 4-6

Equipment Installation ..................................................................................... 4-8

Restricted Area ................................................................................................ 4-9

Battery Handling ............................................................................................4-10

Redundant Power Supplies .......................................................................... 4-12

Backplane Voltage ........................................................................................4-13

Comply with Local and National Electrical Codes ........................................ 4-14

Product Disposal ........................................................................................... 4-15

Hot Swap Fan Warning .................................................................................4-16

Power Cable and AC Adapter ......................................................................4-18

Chapter 5 Advanced Serverboard Setup

5-1 Handling the Serverboard ............................................................................... 5-1

Precautions .....................................................................................................5-1

Unpacking .......................................................................................................5-1

Table of Contents

viii

5-2 Connecting Cables .......................................................................................... 5-2

Connecting Data Cables ................................................................................. 5-2

5-3 Control Panel Connectors and I/O Ports ........................................................ 5-2

Connecting the Control Panel ......................................................................... 5-3

5-4 Processor and Heatsink Installation................................................................5-4

Installing a Passive CPU Heatsink .................................................................5-8

Removing the Heatsink ................................................................................... 5-9

5-5 Installing Memory ..........................................................................................5-10

Removing Memory Modules .........................................................................5-10

Memory Support ............................................................................................5-10

Maximum Memory .........................................................................................5-10

DIMM Module Population Confi guration .................................................. 5-12

5-6 Adding PCI Expansion Cards .......................................................................5-14

5-7 Serverboard Details ...................................................................................... 5-15

5-8 Connector Defi nitions ....................................................................................5-18

5-9 Jumper Settings ............................................................................................ 5-25

Explanation of Jumpers ................................................................................ 5-25

5-10 Onboard Indicators ........................................................................................5-27

5-11 PCI-Express and Serial ATA Connections .................................................... 5-28

5-12 Installing Drivers ............................................................................................5-29

Supero Doctor III ........................................................................................... 5-30

5-13 Onboard Battery ............................................................................................ 5-32

Chapter 6 Advanced Chassis Setup

6-1 Static-Sensitive Devices ..................................................................................6-1

Precautions .....................................................................................................6-1

Unpacking .......................................................................................................6-1

6-2 Control Panel ..................................................................................................6-2

6-3 Chassis Cover ................................................................................................. 6-3

6-4 Air Shrouds .....................................................................................................6-4

6-5 Checking the Airfl ow ....................................................................................... 6-4

6-6 System Fans ................................................................................................... 6-5

6-7 Installing and Removing Hard Drives .............................................................6-6

Accessing the Drive Bays ............................................................................... 6-6

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

6-8 Installing the Serverboard ............................................................................... 6-9

Permanent and Optional Standoffs .................................................................6-9

6-9 Expansion Slot Setup .....................................................................................6-11

6-10 Power Supply ................................................................................................6-13

Power Supply Replacement ..........................................................................6-13

Chapter 7 BIOS

7-1 Introduction ......................................................................................................7-1

Starting BIOS Setup Utility ..............................................................................7-1

How To Change the Confi guration Data ......................................................... 7-1

Starting the Setup Utility .................................................................................7-2

7-2 Main Setup ...................................................................................................... 7-2

7-3 Advanced Settings Menu ................................................................................ 7-4

7-4 Event Logs ....................................................................................................7-28

7-5 IPMI ............................................................................................................... 7-30

7-6 Boot ............................................................................................................... 7-32

7-7 Secur ity ......................................................................................................... 7-33

7-8 Save & Exit ...................................................................................................7-3 4

Appendix A BIOS Error Beep Codes
Appendix B System Specifi cations

ix

Table of Contents

x

Notes

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Chapter 1

Introduction

1-1 Overview

The SuperServer 6017TR-TQF/TFF/TF is a high-end server comprised of two main
subsystems: the SC808BT-1K28BP 2U server chassis and the X9DRT -IBQF/IBFF/F
dual processor serverboard in four hot-swap nodes. Please refer to our web site for
information on operating systems that have been certifi ed for use with the system
(www.supermicro.com).

In addition to the serverboard and chassis, various hardware components have
been included with the SuperServer 6017TR-TQF/TFF/TF server, as listed below:

• Heat Sinks

Two (2) 1U passive CPU heat sinks for rear CPU (SNK-P0047PW)
Two (2) 1U passive CPU heat sinks w/narrow ILM (SNK-P0047PS)

• Two (2) Plastic air shroud (MCP-310-80803-0B)

• Six (6) 40x56-mm 4-pin PWM cooling fans (FAN-0085L4)

• Two (2) Round 50-cm 16-to-16-pin ribbon front control cables (CBL-0087)

• SATA Backplane

One (1) SATA Backplane for four (4) 3.5" HDD (BPN-SAS-808-O-P)
Four (4) hot-swap 3.5" HDD trays (MCP-220-00075-0B)
One (1) Set of SATA 4-51/47/41/37-cm round S-RA cables (CBL-0201L)
Two (2) 4-pin 20-cm power cables, ST to RA (CBL-0212L)

• Two (2) Riser cards (RSC-R1U-E16R-O-P)

• One (1) Rail set (MCP-290-00042-0V)

Note: a complete list of safety warnings is provided on the Supermicro web site at

http://www.supermicro.com/about/policies/safety_information.cfm

Chapter 1: Introduction

1-1

1-2

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

1-2 Serverboard Features

At the heart of the SuperServer 6017TR-TQF/TFF/TF lies the
X9DRT-IBQF/IBFF/F, a dual processor serverboard based on the Intel®
C602 chipset and designed to provide maximum performance. Two of these
serverboards can be mounted in the SC808BT-1K28BP chassis.

The sections below cover the main features of the X9DRT -IBQF/IBFF/F serverboard
(see Figure 1-1 for a block diagram of the chipset).

Processors

The X9DRT-IBQF/IBFF/F supports single or dual Intel® Xeon® E5-2600 series
processors (Socket R LGA 2011). Please refer to the serverboard description pages
on our web site for a complete listing of supported processors (www.supermicro.

com).

Memory

The X9DRT-IBQF/IBFF/F has eight (8) DIMM slots supporting up to 256 GB
of DDR3-1600/1333/1066/800 MHz speed RDIMM/LDIMM registered ECC or
64 GB of DDR3-1600/1333/1066/800 MHz speed UDIMM SDRAM in up to
512 MB, 1 GB, 2 GB, 4 GB, 8 GB, 16 GB or 32 GB sizes at 1.35V or 1.5V
voltages. See Chapter 5 for details.

Note: Check the Supermicro website (www.supermicro.com) for the latest memory
support information.

Serial ATA

A Serial ATA controller is integrated into the C602 to provide up to a six-port
SATA subsystem, (two SATA 3 (6 Gb/s) and four SATA 2 (3 Gb/s), which is either
RAID 0, 1 and 10 (SATA2) or RAID 0, 1, 5 and 10 (SATA3) supported. The SATA
drives are hot-swappable units.

Note: The operati ng system yo u use must h ave R AID su ppor t to e nable t he hot­swap capability and RAI D function of the SATA drives.

PCI Expansion Slots

The SuperServer 6017TR-TQF/TFF/TF has for each node
one (1) PCI Express 3.0 x16 slot available for use with a riser card.

1-3

Chapter 1: Introduction

Onboard Controllers/Ports

One Fast UART 16550 serial port, one 9-pin RS-232 port and a Mellonox
Connect-X3 Infi niBand (on 6017TR-TQF and 6017TR-TFF servers only) supporting
a single QSFP connector are located on the serverboard. The color-coded I/O ports
include one COM port, a VGA (monitor) port, two USB 2.0 ports (additional one
internal USB Type-A connector is included on the serverboard), an IPMI dedicated
LAN port and two Ethernet ports.

Note: For IPMI Confi guration Instructions, please refer to the Embedded BMC
Configuration User's Guide available @

http://www.supermicro.com/support/

manuals/.

Graphics Controller

The X9DRT-IBQF/IBFF/F features an integrated Matrox G200eW Video Controller.

Infi niBand

The 6017TR-TQF ser ver inc lud e a QDR (quad dat a rate) speed I nfi niBand QSFP
connector. The 6017TR-TFF server includes a FDR (fourteen data rate) speed
Infi niBand QSFP connector. Infi niBand is a scalable serial communications link
intended for connecting processors with high-speed peripherals.

Other Features

Other onboard features that promote system health include onboard voltage
monitors, a chassis intrusion header, auto-switching voltage regulators, chassis and
CPU overheat sensors, virus protection, node manager software and BIOS rescue.

1-4

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

1-3 Server Chassis Features

The following is a general outline of the main features of the SC808 server chassis.

System Power

Each SC808 chassis model includes a high-effi ciency 80-plus Platinum certifi ed
power supply, rated at 1280 Watts plus one redundant backup power supply.
In the unlikely event your power supply fails, replacement is simple and can be
accomplished without tools.

SATA Subsystem

The SC808 supports up to four (4) 3.5" hot-swap SATA drives in trays (two for each
node). These drives are hot-swappable units and are connected to a backplane that
provides power and control.

Note: The operating system you use must have RAID support to enable the hot­swap capability of the drives.

Front Control Panel

SC808BT-1K28BP chassis includes four front panels on the handles of the chassis
which control each of the systems. Each control panel on the SUPERSERVER
6017TR-TQF/TFF/TF provides you with system monitoring and control for one
server node. LEDs indicate system power, HDD activity, network activity, system
overheat and power supply failure. A main power button and a system reset button
are also included.

I/O Ports

The SC808 is an proprietary form factor chassis designed to be used in a 1U
rackmount confi guration. The SC808 chassis provides a low-profi le add-on card
slot, a COM port, a VGA port, two USB 2.0 ports , one IPMI Ethernet port and two
gigabit Ethernet ports per node.

1-5

Chapter 1: Introduction

Cooling System

The SC808 chassis accepts six (6) 4-cm system fans powered from either backpane
or the serverboards. If not powered from the backpane, the SC808BT-1K28BP
model chassis powers three fans from each of the two serverboards, so that when
one of the serverboard drawers is removed, the other serverboards will continue
running its fans.

Air Shrouds

The SC808 chassis includes two plastic air shrouds that direct the airfl ow where
cooling is needed on each serverboard. Always use the air shroud included with
your chassis on each serverboard.

Mounting Rails

The SC808 includes a set of quick-release rails, and can be placed in a rack for
secure storage and use. To setup your rack, follow the step-by-step instructions
included in this manual.

1-4 Advanced Power Management

Intel® Intelligent Power Node Manager (NM)

The Intel® Intelligent Power Node Manager (IPNM) provides your system with
real-time thermal control and power management for maximum energy effi ciency.
Although IPNM Specifi cation Version 1.5 is supported by the BMC (Baseboard
Management Controller), your system must also have IPNM-compatible
Manageability Engine (ME) fi rmware installed to use this feature.

Manageability Engine (ME)

The Manageability Engine, which is an ARC controller embedded in the IOH (I/O
Hub), provides Server Platform Services (SPS) to your system. The services
provided by SPS are different from those proveded by the ME on client platforms.

1-6

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Figure 1-1. Intel C602 Chipset:

System Block Diagram

Note: This is a general block diagram and may not exactly repre-

sent the features on your serverboard. See the previous pages for

the actual specifi cations of your serverboard. This block diagram is

intended for your reference only.

E5-2600

E5-2600

QPI

DDR3 DIMM

DDR3 DIMM

DDR3 DIMM

DDR3 DIMM

#1

G

SSB

C602J

PEG0

DMI

PEG1_4:1

PEG1_8

PCI-32bit

USB

LAN
I350
2 ports

AT25321

IB
FDR/QDR

LPC

CPU FRONT

FAN Side

CPU REAR

(I/O Side)

USB

REAR

Type A

0,1

2

H

F

E

Socket 1

Socket 2

#1

P0

P0

P1

P1

PE3 PE2 PE1 DMI

PE3 PE2 PE1 DMI

Gen3
x16

x4

VGA BMC

WPCM450

DDR2

LAN

RTL8201F

SPI

SATA

Gen2

Gen1/2

PCI-E x16 SLOT

x4

RJ45 RJ45

Gen3

x16

Gen3

x16

x8

x8(8..15)

SATA3 #0

SATA3 #1

SATA2 #2

SATA2 #3

SATA3 #4

SATA3 #5

6/3/1.5

QPI

VGA CONN

DDR3 DIMM

DDR3 DIMM

#1

C

#1

D

DDR3 DIMM

DDR3 DIMM

A

B

#1

#1

#1

#1

J1

W83527HG

SI/O

1-7

Chapter 1: Introduction

1-5 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email:

[e-mail] (General Information)

[e-mail] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email:

[e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Asia-Pacifi c

Address: Super Micro Computer, Inc.

4F, No. 232-1, Liancheng Rd
New Taipei City 235

Taiwan
Tel: [phone]
Fax: [phone]
Web Site:

www.supermicro.com.tw

Technical Support:
Email: [e-mail]
Tel: [phone]

1-8

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

1-6 2U Twin2: System Notes

As a 2U Twin2 confi guration, the SuperServer 6017TR-TQF/TFF/TF is a unique
server system. With two system boards incorporated into a single chassis acting as
two separate nodes, there are several points you should keep in mind.

Nodes

Each of the two serverboards act as a separate node in the system. As independant
nodes, each may be powered off and on without affecting the others. In addition,
each node is a hot-swappable unit that may be removed from the rear of the chassis.
The nodes are connected to the server backplane by means of an adapter card.

Note: A guide pin is located between the upper and lower nodes on the inner chassis
wall. This guide pin also acts as a “stop” when a node is fully installed. If too much
force is used when inserting a node this pin may break off. Take care to slowly slide
a node in until you hear the “click” of the locking tab seating itself.

System Power

Dual 1280 Watt power supplies are used to provide the power for all serverboards.
Each serverboard however, can be shut down independently of the other with the
power button on its own control panel.

SATA Backplane/Drives

As a system, the SuperServer 6017TR-TQF/TFF/TF supports the use of twelve
SATA drives. A single SATA backplane works to apply system-based control for
power and fan speed functions, yet at the same time logically connects a set of two
SA T A drives to each serverboard. Consequently , RAID setup is limited to a two-drive
scheme (RAID cannot be spread across all drives). See the Drive Bay Installation/
Removal section in Chapter 6 for the logical hard drive and node confi guration.

Chapter 2: Server Installation

2-1

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your SuperServer
6017TR-TQF/TFF/TF up and running. Following these steps in the order given
should enable you to have the system operational within a minimum amount of time.
This quick setup assumes that your system has come to you with the processors
and memory preinstalled. If your system is not already fully integrated with a
serverboard, processors, system memory etc., please turn to the chapter or section
noted in each step for details on installing specifi c components.

2-2 Unpacking the System

You should inspect the box the SuperServer 6017TR-TQF/TFF/TF was shipped
in and note if it was damaged in any way. If the server itself shows damage you
should fi le a damage claim with the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the SuperServer
6017TR-TQF/TFF/TF. It should be situated in a clean, dust-free area that is well
ventilated. Avoid areas where heat, electrical noise and electromagnetic fi elds are
generated. You will also need it placed near a grounded power outlet. Read the
Rack and Server Precautions in the next section.

2-3 Preparing for Setup

The box the SuperServer 6017TR-TQF/TFF/TF was shipped in should include two
sets of rail assemblies, two rail mounting brackets and the mounting screws you
will need to install the system into the rack. Follow the steps in the order given to
complete the installation process in a minimum amount of time. Please read this
section in its entirety before you begin the installation procedure outlined in the
sections that follow.

2-2

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

2-4 Cautions!

Choosing a Setup Location

• Leave enough clearance in front of the rack to enable you to open the front door

completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for suffi cient airfl ow and ease in servicing.

• This product is for installation only in a Restricted Access Location (dedicated

equipment rooms, service closets and the like).

• This product is not suitable for use with visual display work place devices

acccording to §2 of the the German Ordinance for Work with Visual Display Units.

Rack Precautions

• Ensure that the leveling jacks on the bottom of the rack are fully extended to

the fl oor with the full weight of the rack resting on them.

• In single rack installation, stabilizers should be attached to the rack. In multiple

rack installations, the racks should be coupled together.

• Always make sure the rack is stable before extending a component from the

rack.

• You should extend only one component at a time - extending two or more

simultaneously may cause the rack to become unstable.

Server Precautions

• Review the electrical and general safety precautions in Chapter 4.

• Determine the placement of each component in the rack before you install the

rails.

• Install the heaviest server components on the bottom of the rack fi rst, and then

work up.

• Use a regulating uninterruptible power supply (UPS) to protect the server from

power surges, voltage spikes and to keep your system operating in case of a
power failure.

• Allow any hot plug drives and power supply modules to cool before touching

them.

• Always keep the rack's front door and all panels and components on the servers

closed when not servicing to maintain proper cooling.

Chapter 2: Server Installation

2-3

Rack Mounting Considerations

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating
temperature of the rack environment may be greater than the ambient temperature
of the room. Therefore, consideration should be given to installing the equipment
in an environment compatible with the manufacturer’s maximum rated ambient
temperature (Tmra).

Reduced Airfl ow

Equipment should be mounted into a rack so that the amount of airfl ow required
for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.

Circuit Overloading

Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack
itself should be grounded. Particular attention should be given to power supply
connections other than the direct connections to the branch circuit (i.e. the use of
power strips, etc.).

Warning! To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system remains
stable. The following guidelines are provided to ensure your safety:

• This unit should be mounted at the bottom of the rack if it is the only unit in

the rack.

• When mounting this unit in a partially fi lled rack, load the rack from the bottom

to the top with the heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before

mounting or servicing the unit in the rack.

2-4

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

2-5 Installing the System into a Rack

This section provides information on installing the SC808 chassis into a rack unit
with the rails provided. There are a variety of rack units on the market, which
may mean the assembly procedure will differ slightly. You should also refer to the
installation instructions that came with the rack unit you are using.

NOTE: This rail will fi t a rack between 26" and 33.5" deep.

Identifying the Sections of the Rack Rails

The chassis package includes two rack rail assemblies in the rack mounting kit.
Each assembly consists of two sections: an inner fi xed chassis rail that secures
directly to the server chassis and an outer fi xed rack rail that secures directly to
the rack itself (Figure 2-1).

Figure 2-1: Identifying the Sections of the Rack Rails

(Right side rail shown)

Rail Extension

(Inner Rail is preinstalled

to the chassis)

Outer Rails

Chapter 2: Server Installation

2-5

Figure 2-2: Installing the Inner Rail Extensions

Installing the Inner Rail Extension

The SC808 chassis includes a set of inner rails in two sections: Inner rails and inner
rail extensions. The inner rails are preattached and do not interfere with normal use
of the chassis if you decide not to use a server rack. Attach the inner rail extension
to stabilize the chassis within the rack.

Installing the Inner Rails (Figure 2-2)

1. Place the inner rack extensions on the side of the chassis aligning the hooks
of the chassis with the rail extension holes. Make sure the extension faces
"outward" just like the preattached inner rail.

2. Slide the extension toward the front of the chassis.

3. Secure the chassis with two screws as illustrated.

4. Repeat steps 1-3 for the other inner rail extension.

1

1

1

2

1

3

2-6

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Outer Rack Rails

Outer rails attach to the rack and hold the chassis in place.

Installing the Outer Rails to the Rack (Figure 2-3)

1. Attach the short bracket to the outside of the long bracket. You must align the
pins with the slides. Also, both bracket ends must face the same direction.

2. Adjust both the short and long brackets to the proper distance so that the rail
fi ts snugly into the rack.

3. Secure the long bracket to the front side of the outer rail with two M5 screws
and the short bracket to the rear side of the outer rail with three M5 screws.

4. Repeat steps 1-4 for the left outer rail.

Installing the Chassis into a Rack (Figure 2-4)

1. Confi rm that chassis includes the inner rails (A) and rail extensions (B). Also,
confi rm that the outer rails (C) are installed on the rack.

2. Line chassis rails (A and B) with the front of the rack rails (C).

3. Slide the chassis rails into the rack rails, keeping the pressure even on both
sides (you may have to depress the locking tabs when inserting). When the
server has been pushed completely into the rack, you should hear the locking
tabs "click".

4. (Optional) Insert and tightening the thumbscrews that hold the front of the
server to the rack.

Figure 2-3. Assembling the Outer Rails

Secure to the

Front of the Rack

Secure to the Rear

of the Rack

Attach Outer Racks

together

Chapter 2: Server Installation

2-7

Figure 2-4: Installing the Rack Rails

Note: The fi gure above is for illustration purposes only. Always install servers to

the bottom of the rack fi rst.

1

C

1

B

1

A

Stability hazard. The rack stabilizing mechanism must be in place, or the

rack must be bolted to the fl oor before you slide the unit out for servicing.
Failure to stabilize the rack can cause the rack to tip over.

2-8

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Figure 2-5. Accessing the Inside of the System

2-6 Checking the Serverboard Setup

After you install the SuperServer 6017TR-TQF/TFF/TF in the rack, you will need
to open the unit to make sure the serverboard is properly installed and all the
connections have been made.

Accessing the inside of the System

Before operating the server for the fi rst time, it is important to remove the protective
fi lm covering the top of the chassis, in order to allow for proper ventilation and

cooling.

Removing the Chassis Cover and Protective Film (Figure 2-5)

1. Disconnect the chassis from any power source and remove all four screws.

2. Gently push down on the chassis cover in the areas indicated in the
illustration.

3. Push the cover toward the rear of the chassis and lift the cover upwards and
off the chassis.

4. Peel off the protective fi lm covering the top cover and the top of the chassis

5. Check that all ventilation openings on the top cover and the top of the chassis
are clear and unobstructed.

Remove this

screw

Remove this

screw

Remove this

screw

1

3

1

2

1

2

1

3

Chapter 2: Server Installation

2-9

Checking the Components and Setup

1. You may have one or two processors already installed into the serverboard.
Each processor needs its own heat sink. See Chapter 5 for instructions on
processor and heat sink installation.

2. Your SuperServer 6017TR-TQF/TFF/TF server system may have come with
system memory already installed. Make sure all DIMMs are fully seated in
their slots. For details on adding system memory, refer to Chapter 5.

3. If desired, you can install add-on cards to the system. See Chapter 5 for
details on installing PCI add-on cards.

4. Make sure all power and data cables are properly connected and not blocking
the chassis airfl ow. Also make sure that no cables are positioned in front of
the fans. See Chapter 5 for details on cable connections.

2-7 Checking the Drive Bay Setup

Next, you should check to make sure the peripheral drives and the SATA drives
have been properly installed and all connections have been made.

Checking the Drives

1. All drives are accessable from the front of the server. A hard drive can be
installed and removed from the front of the chassis without removing the top
chassis cover.

2. Depending upon your system's confi guration, your system may have one or
more drives already installed. If you need to install hard drives, please refer to
Chapter 6.

Checking the Airfl ow

1. Airfl ow is provided by six hot-swappable 4-cm chassis cooling fans in two
housings. The system component layout was carefully designed to direct
suffi cient cooling airfl ow to the components that generate the most heat.

2. Note that all power and data cables have been routed in such a way that they
do not block the airfl ow generated by the fans.

Providing Power

1. Plug the power cord(s) from the power supply unit(s) into a high-quality
power strip that offers protection from electrical noise and power surges. It is
recommended that you use an uninterruptible power supply (UPS).

2. Depress the power on button on the front of the chassis.

2-10

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Caution: Except for short periods of time, do NOT operate the server without
the cover in place. The chassis cover must be in place to allow proper airfl ow
and prevent overheating.

Chapter 3: System Interface

3-1

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the control panel and on the drive carriers to keep you
constantly informed of the overall status of the system. SC808 models include
four front panels on the handles of the chassis which control each of the systems.

This chapter explains the meanings of all LED indicators and the appropriate
response you may need to take.

Figure 3-1: Control Panel

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

3-2

3-2 Control Panel Button

There are two push-buttons located on the front of the chassis. These are (in order
from left to right) a reset button and a power on/off button.

• Reset: The reset button is used to reboot the system.

• Power: The main power switch is used to apply or remove power from the power

supply to the server system. Turning off system power with this button removes
the main power but keeps standby power supplied to the system. Therefore,
you must unplug system before servicing.

3-3 Control Panel LEDs

The control panel located on the front of the SC808 chassis has fi ve LEDs. These
LEDs provide you with critical information related to different parts of the system.
This section explains what each LED indicates when illuminated and any corrective
action you may need to take.

• Universal Information LED: The Universal Information LED is used to indicate

fan failure, power failure, overheat condition, or to identify the unit within a large
rack installation. The feature requires a serverboard that supports the Universal
Information LED.

When this LED blinks red quickly, it indicates a fan failure and when blinking red
slowly a power failure. This LED will be blue when used for UID (Unit Identifi er).
When on continuously red, it indicates an overheat condition, which may be caused
by cables obstructing the airfl ow in the system or the ambient room temperature
being too warm. See the table below for descriptions of the LED states

Chapter 3: System Interface

3-3

• NIC2: Indicates network activity on GLAN2 when fl ashing

• NIC1: Indicates network activity on GLAN1 when fl ashing

• HDD: Indicates IDE channel activity , SATA drive, and/or DVD-ROM drive activity

when fl ashing.

• Power: Indicates power is being supplied to the system's power supply units.

This LED should normally be illuminated when the system is operating.

3-4 Drive Carrier LEDs

The server chassis uses SATA drives.

SATA Drives

Each SATA drive carrier has two LEDs.

• Blue: Each Serial ATA drive carrier has a green LED. When illuminated, this

green LED (on the front of the SATA drive carrier) indicates drive activity. A
connection to the SATA backplane enables this LED to blink on and off when
that particular drive is being accessed.

• Red: The red LED to indicate an SATA drive failure. If one of the SATA drives

fail, you should be notifi ed by your system management software.

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

3-4

SAS Drives

This server system does not support SAS drives at this time.

4-1

Chapter 4: Warning Statements for AC Systems

Chapter 4

Standardized Warning Statements for AC Systems

4-1 About Standardized Warning Statements

The following statements are industry standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions
or experience difficulty, Contact Supermicro's Technical Support department
for assistance. Only certifi ed technicians should attempt to install or confi gure
components.

Read this appendix in its entirety before installing or confi guring components in the
Supermicro chassis.

These warnings may also be found on our web site at http://www.supermicro.

com/about/policies/safety_information.cfm.

Warning!

This warning symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.

Warning Defi nition

警告の定義

この警告サインは危険を意味します。

人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、

電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。

此警告符号代表危险。

您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前，必须充分
意识到触电的危险，并熟练掌握防止事故发生的标准工作程序。请根据每项警告结
尾的声明号码找到此设备的安全性警告说明的翻译文本。

4-2

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befi nden sich in einer Situation, die zu

Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den
Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung
vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen
Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes

de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y
familiarícese con los procedimientos estándar de prevención de accidentes. Al
fi nal de cada advertencia encontrará el número que le ayudará a encontrar el texto
traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES
IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une

situation pouvant entraîner des blessures ou des dommages corporels. Avant
de travailler sur un équipement, soyez conscient des dangers liés aux circuits
électriques et familiarisez-vous avec les procédures couramment utilisées pour
éviter les accidents. Pour prendre connaissance des traductions des avertissements
fi gurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fi n de chaque avertissement.

CONSERVEZ CES INFORMATIONS.

ןונקת תורהצהאהרהז

ןה תואבה תורהצהא ינפמ שמתשמה תא ריהזהל תנמ לע ,היישעתה ינקת יפ לע תורהז הלבח

ה וא תולאש שיו הדימב .תירשפא תיזיפי ,יהשלכ היעבב תולקתרוציל שי הכימת תקלחמ םע רשק

רידגהל וא ןיקתהל םיאשר דבלב םיכמסומ םיאנכט .ורקימרפוס לש תינכט תאה .םיביכר

אורקל שי .ורקימרפוס יזראמב םיביכרה

תרדגה וא תנקתה ינפל ואולמב חפסנה תא

4-3

Warning Statements for AC Systems

안전을 위한 주의사항

경고!

이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수
있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와
관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준
작업절차를 준수해 주시기 바랍니다.

해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를
참조하십시오

BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die

lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,
dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's
en dient u op de hoogte te zijn van de standaard procedures om ongelukken te
voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te
herleiden naar de desbetreffende locatie.

BEWAAR DEZE INSTRUCTIES

. ﻲﻓ ﻚﻧﺍ ﻥﺃ ﻦﻜﻤﻳ ﺔﻟﺎﺣ ﻲﻓ ﺐﺒﺴﺘﺗ ﺔﺑﺎﺻﺍ ﺔﻳﺪﺴﺟ ﺰﻣﺮﻟﺍ ﺍﺬﻫ ﻲﻨﻌﻳ ﺮﻄﺧ !ﺮﻳﺬﺤﺗ

ﻥﺃ ﻞﺒﻗ ﻱﺃ ﻰﻠﻋ ﻞﻤﻌﺗ ﺕﺍﺪﻌﻣ،ﻛﻢﻠﻋ ﻰﻠﻋ ﻦ ﻦﻋ ﺔﻤﺟﺎﻨﻟﺍ ﺮﻁﺎﺨﻤﻟﺎﺑ ﺮﺋﺍﻭﺪﻟﺍ

ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ

ﻛﻭﺔﻳﺍﺭﺩ ﻰﻠﻋ ﻦ ﺭﺎﻤﻤﻟﺎﺑﺕﺎﺳ ﺔﻴﺋﺎﻗﻮﻟﺍ ﻟ ﻊﻨﻤﻉﻮﻗﻭ ﻱﺃﺙﺩﺍﻮﺣ

ﻢﻗﺭ ﻡﺪﺨﺘﺳﺍ ﻥﺎﻴﺒﻟﺍ ﺹﻮﺼﻨﻤﻟﺍ ﺔﻳﺎﻬﻧ ﻲﻓ ﺮﻳﺬﺤﺗ ﻞﻛ ﺭﻮﺜﻌﻠﻟ ﺎﻬﺘﻤﺟﺮﺗ

4-4

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Installation Instructions

Warning!

Read the installation instructions before connecting the system to the power source.

Warnung
Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen

lesen.

¡Advertencia!
Lea las instrucciones de instalación antes de conectar el sistema a la red de

alimentación.

Attention
Avant de brancher le système sur la source d'alimentation, consulter les directives

d'installation.

設置手順書

システムを電源に接続する前に、設置手順書をお読み下さい。

ﻟﺍ ﺕﺍﺩﺎﺷﺭﺇ ﺮﻗﺍﺐﻴﻛﺮﺘ ﻞﻴﺻﻮﺗ ﻞﺒﻗ ﻰﻟﺇ ﻡﺎﻈﻨﻟﺍ ﺔﻗﺎﻄﻠﻟ ﺭﺪﺼﻣ

אורקל שי רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תאחתמ.

시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오.

Waarschuwing
Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron

aansluit.

4-5

Chapter 4: Warning Statements for AC Systems

Circuit Breaker

Warning!

This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.

サーキット・ブレーカー

この製 品 は、短絡（過電流）保護装置がある建物での設置を前提としています。

保護装置の定格が250V、20Aを超えないことを確認下さい。

Warnung
Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss-

bzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der
Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt.

¡Advertencia!
Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes)

del edifi cio. Asegúrese de que el dispositivo de protección no sea superior a: 250
V, 20 A.

Attention
Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit

dépend de l'installation électrique du local. Vérifi ez que le courant nominal du
dispositif de protection n'est pas supérieur à :250 V, 20 A

לע ךמתסמ הז רצומנגהה תעינמל םינבמב תנקתומה יכ אדוול שי .ילמשח רצק

רצקה ינפמ ןגמה רישכמה ילמשחהמ רתוי אל אוה-250 V, 20 A

ﺞﺘﻨﻤﻟﺍ ﺍﺬﻫ ﻰﻠﻋ ﺪﻤﺘﻌﻳ ﺕﺍﺪﻌﻣ ﺔﻳﺎﻤﺤﻟﺍ ﺓﺮﻴﺼﻘﻟﺍﺮﺋﺍﻭﺪﻟﺍ ﻦﻣ ﺎﻬﺘﻴﺒﺜﺗ ﻢﺗ ﻲﺘﻟﺍ ﻲﻓ

ﻰﻨﺒﻤﻟﺍ

20A, 250V : ﻦﻣ ﺪﻛﺄﺗ ﻥﺃ ﻢﻴﻴﻘﺗ ﺯﺎﻬﺠﻟﺍ ﻟﺍﻲﺋﺎﻗﻮ ﺲﻴﻟ ﻦﻣ ﺮﺜﻛﺃ

4-6

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Power Disconnection Warning

Warning!

The system must be disconnected from all sources of power and the power cord
removed from the power supply module(s) before accessing the chassis interior to
install or remove system components.

電源切断の警告

システムコンポーネントの取り付けまたは取り外しのために、シャーシー内部にアクセス

するには、

システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り

外す必要があります。

在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线.

Warnung
Das System muss von allen Quellen der Energie und vom Netzanschlusskabel

getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es
auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder
zu entfernen.

¡Advertencia!
El sistema debe ser disconnected de todas las fuentes de energía y del cable

eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso
el interior del chasis para instalar o para quitar componentes de sistema.

경고!

이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에
의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지

않도록 해야 합니다.

Waarschuwing
Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van

uw electrische installatie. Controleer of het beveiligde aparaat niet groter
gedimensioneerd is dan 220V,20A.

4-7

Chapter 4: Warning Statements for AC Systems

Le système doit être débranché de toutes les sources de puissance ainsi que de
son cordon d'alimentation secteur avant d'accéder à l'intérieur du chassis pour
installer ou enlever des composants de systéme.

ילמשח קותינ ינפמ הרהזא

!הרהזא

למשחה תורוקמ לכמ תכרעמה תא קתנל שי ריסהל שיו קפסהמ ילמשחה לבכ תא

נקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפלת רסה ואת .םיביכר

ﻞﺼﻓ ﺐﺠﻳ ﻡﺎﻈﻨﻟﺍ ﻊﻴﻤﺟ ﻦﻣﺭﺩﺎﺼﻣ ﺔﻗﺎﻄﻟﺍ ﺔﻟﺍﺯﺇﻭ ءﺎﺑﺮﻬﻜﻟﺍ ﻚﻠﺳ ﻦﻣ ﺓﺪﺣﻭ ﺩﺍﺪﻣﺍ

ﺔﻗﺎﻄﻟﺍ ﻞﺒﻗ

ﻰﻟﺇ ﻝﻮﺻﻮﻟﺍ ﺔﻴﻠﺧﺍﺪﻟﺍ ﻖﻁﺎﻨﻤﻟﺍ ﻟﻞﻜﻴﻬﻠ ﺔﻟﺍﺯﺇ ﻭﺃ ﺖﻴﺒﺜﺘﻟ ﺕﺎﻧﻮﻜﻣ

ﺯﺎﻬﺠﻟﺍ

경고!

시스템에 부품들을 장착하거나 제거하기 위해서는 섀시 내부에 접근하기 전에
반드시 전원 공급장치로부터 연결되어있는 모든 전원과 전기코드를 분리해주어야
합니다.

Waarschuwing
Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren

of verwijderen van systeem onderdelen, dient u alle spanningsbronnen en alle
stroomkabels aangesloten op de voeding(en) van de behuizing te verwijderen

4-8

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Equipment Installation

Warning!

Only trained and qualifi ed personnel should be allowed to install, replace, or service
this equipment.

機器の設置

トレーニングを受け認定された人だけがこの装置の設置、交換、またはサービスを許可
されています。

Warnung
Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,

qualifi ziertem Personal gestattet werden.

¡Advertencia!
Solamente el personal califi cado debe instalar, reemplazar o utilizar este equipo.

Attention
Il est vivement recommandé de confier l'installation, le remplacement et la

maintenance de ces équipements à des personnels qualifi és et expérimentés.

!הרהזא

שר דבלב ךמסומ תווצתא ףילחהל ,ןיקתהל יא .דויצה רובע תוריש תתל וא דויצה

ﻦﻴﺑﺭﺪﻤﻟﺍﻭ ﻭ ﺐﻴﻛﺮﺘﻟﻝﺍﺪﺒﺘﺳﺍ ﻭﺃ ﺔﻣﺪﺧ ﺯﺎﻬﺠﻟﺍ ﺍﺬﻫ ﺢﻤﺴﻳ ﻥﺃ ﺐﺠﻳ ﻂﻘﻓ ﻦﻴﻠﻫﺆﻤﻟﺍ ﻦﻴﻔﻅﻮﻤﻠﻟ

경고!

훈련을 받고 공인된 기술자만이 이 장비의 설치, 교체 또는 서비스를 수행할 수
있습니다.

4-9

Chapter 4: Warning Statements for AC Systems

Warning!

This unit is intended for installation in restricted access areas. A restricted access
area can be accessed only through the use of a special tool, lock and key, or other
means of security. (This warning does not apply to workstations).

アクセス制限区域

このユ ニットは、アクセス制限区域に設置されることを想定しています。

アクセス制限区域は、特別なツール、鍵と錠前 、その他のセキュリティの手段を用いての

み出入りが可能です。

Restricted Area

Waarschuwing
Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door

geschoold en gekwalifi ceerd personeel.

Warnung
Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen.

Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und
Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich.

¡Advertencia!
Esta unidad ha sido diseñada para instalación en áreas de acceso restringido.

Sólo puede obtenerse acceso a una de estas áreas mediante la utilización de una
herramienta especial, cerradura con llave u otro medio de seguridad.

Attention
Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une

zone d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme
de verrouillage et une clé, ou tout autre moyen de sécurité.

4-10

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Battery Handling

Warning!

There is the danger of explosion if the battery is replaced incorrectly. Replace the
battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions

תלבגומ השיג םע רוזא

!הרהזא

תרזעב תנתינ השיגה .השיג תלבגה םהב שיש םירוזאב הדיחיה תא ןיקתהל שי

.('דכו לוענמ ,חתפמ) דבלב החטבא ילכ

. ﺺﻴﺼﺨﺗ ﺓﺪﺣﻮﻟﺍ ﻩﺬﻫ ﻲﻓ ﺎﻬﺒﻴﻛﺮﺘﻟ ﻖﻁﺎﻨﻣ ﺓﺭﻮﻈﺤﻣ ﻢﺗ

ﺻﻮﻟﺍ ﻦﻜﻤﻳﻰﻟﺇ ﻝﻮ ﺔﻘﻄﻨﻣ ﺓﺭﻮﻈﺤﻣ ﻂﻘﻓ ﻡﺍﺪﺨﺘﺳﺍ ﻝﻼﺧ ﻦﻣ ،ﺔﺻﺎﺧ ﺓﺍﺩﺃ

ﻭﺃ ﻱﺃ ﻼﻟ ﻯﺮﺧﺃ ﺔﻠﻴﺳﻭﻥﺎﻣﻷ ﺡﺎﺘﻔﻣﻭ ﻞﻔﻗ

경고!

이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다. 특수도구, 잠금 장치 및
키, 또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다.

Waarschuwing
Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang.

Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te
maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメー
カーが推奨する型、または同 等のものを使用下さい。使用済電池は製造元の指示に従

って処 分して 下さい。

4-11

Chapter 4: Warning Statements for AC Systems

Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die

Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.

Attention
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer

que par une pile de type semblable ou équivalent, recommandée par le fabricant.
Jeter les piles usagées conformément aux instructions du fabricant.

¡Advertencia!
Existe peligro de explosión si la batería se reemplaza de manera incorrecta.

Reemplazar la batería exclusivamente con el mismo tipo o el equivalente
recomendado por el fabricante. Desechar las baterías gastadas según las
instrucciones del fabricante.

!הרהזא

תנכס תמייקץוציפ .הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי

גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ.

תוללוסה קוליס תושמושמה עצבל שי .ןרציה תוארוה יפל

ﺮﻄﺧ ﻙﺎﻨﻫ ﻦﻣ ﻝﺍﺪﺒﺘﺳﺍ ﺔﻟﺎﺣ ﻲﻓ ﺭﺎﺠﻔﻧﺍ ﺔﻳﺭﺎﻄﺒﻟﺍ ﺔﺤﻴﺤﺻ ﺮﻴﻏ ﺔﻘﻳﺮﻄﺑ ﻚﻴﻠﻌﻓ

ﺔﻳﺭﺎﻄﺒﻟﺍ ﻝﺍﺪﺒﺘﺳﺍ

ﻂﻘﻓ ﻉﻮﻨﻟﺍ ﺲﻔﻨﺑ ﺎﻬﻟﺩﺎﻌﻳ ﺎﻣ ﻭﺃ ﺎﻤﻛﺖﺻﻭﺃ ﺔﻌﻨﺼﻤﻟﺍ ﺔﻛﺮﺸﻟﺍ ﻪﺑ

ﺕﺎﻳﺭﺎﻄﺒﻟﺍ ﻦﻣ ﺺﻠﺨﺗ ﻟ ﺎﻘﻓﻭ ﺔﻠﻤﻌﺘﺴﻤﻟﺍﺔﻌﻧﺎﺼﻟﺍ ﺔﻛﺮﺸﻟﺍ ﺕﺎﻤﻴﻠﻌﺘ

경고!

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와
동일하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다.
제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.

Waarschuwing
Er is ontploffi ngsgevaar indien de batterij verkeerd vervangen wordt. Vervang de

batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen
wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd
te worden.

4-12

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Warnung
Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass

der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.

¡Advertencia!
Puede que esta unidad tenga más de una conexión para fuentes de alimentación.

Para cortar por completo el suministro de energía, deben desconectarse todas las
conexiones.

Attention
Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute

tension et tout courant électrique de l'unité, toutes les connexions d'alimentation
doivent être débranchées.

Redundant Power Supplies

Warning!

This unit might have more than one power supply connection. All connections must
be removed to de-energize the unit.

冗長電源装置

このユニットは複数の電源装置が接続されている場合があります。

ユニットの電源を切るためには、すべての接続を取り外さなければなりません。

דחא קפסמ רתוי םייק םא

!הרהזא

.קפס לש דחא רוביחמ רתוי שי הדחיל תא ריסהל שיןקורל תנמ לע םירוביחה לכ

חיה תאי.הד

4-13

Chapter 4: Warning Statements for AC Systems

Backplane Voltage

Warning!

Hazardous voltage or energy is present on the backplane when the system is
operating. Use caution when servicing.

バックプレーンの電圧

システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。

修理する際には注意ください。

直流电源终端可能会产生危险的电压或能量.终端不使用时,请务必盖上机盖.机盖盖
上后,请确保导体未绝缘部分无法使用.

Warnung
Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche

Spannungen oder Energien auf. Vorsicht bei der Wartung.

¡Advertencia!
Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso.

Tenga cuidado cuando lo revise.

Attention
Lorsque le système est en fonctionnement, des tensions électriques circulent sur

le fond de panier. Prendre des précautions lors de la maintenance.

. ﺪﻗ ﺍﺬﻬﻟ ﻥﻮﻜﻳ ﻟﺍﺯﺎﻬﺠ ﺕﻻﺎﺼﺗﺍ ﺓﺪﻋ ﺕﺍﺪﺣﻮﺑ ﺔﻗﺎﻄﻟﺍ ﺩﺍﺪﻣﺍ

ﺔﻟﺍﺯﺇ ﺐﺠﻳ ﺕﻻﺎﺼﺗﻻﺍ ﺔﻓﺎﻛ ﻝﺰﻌﻟ ﻟﺍﺓﺪﺣﻮ ﻦﻋ ءﺎﺑﺮﻬﻜﻟﺍ

경고!

이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에
전원을 차단하기 위해서는 모든 연결 단자를 제거해야만 합니다.

Waarschuwing
Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle

aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken.

4-14

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Comply with Local and National Electrical Codes

Warning!

Installation of the equipment must comply with local and national electrical codes.

地方および国の電気規格に準拠

機器の取り付けはその地方および国の電気規格に準拠する必要があります。

Warnung
Die Installation der Geräte muss den Sicherheitsstandards entsprechen.

¡Advertencia!
La instalacion del equipo debe cumplir con las normas de electricidad locales y

nacionales.

ﻙﺎﻨﻫ ﺮﻄﺧ ﻦﻣ ﻲﺋﺎﺑﺮﻬﻜﻟﺍ ﺭﺎﻴﺘﻟﺍ ﻰﻠﻋ ﺓﺩﻮﺟﻮﻤﻟﺍ ﺔﻗﺎﻄﻟﺍﻭﺃ ﺔﺣﻮﻠﻟﺍ

ﻥﻮﻜﻳ ﺎﻣﺪﻨﻋﻡﺎﻈﻨﻟﺍ ﻞﻤﻌﻳ ﺪﻨﻋ ﺍﺭﺬﺣ ﻦﻛ ﺔﻣﺪﺧ ﺯﺎﻬﺠﻟﺍ ﺍﺬﻫ

경고!

시스템이 동작 중일 때 후면판 (Backplane)에는 위험한 전압이나 에너지가 발생
합니다. 서비스 작업 시 주의하십시오.

Waarschuwing
Een gevaarlijke spanning of energie is aanwezig op de backplane wanneer het

systeem in gebruik is. Voorzichtigheid is geboden tijdens het onderhoud.

ירוחאה לנפב חתמ

זא!הרה

ךלהמב רהזיהל שי .תכרעמה לועפת ןמזב ירוחאה לנפב חתמ תנכס תמייק

.הדובעה

4-15

Chapter 4: Warning Statements for AC Systems

Product Disposal

Warning!

Ultimate disposal of this product should be handled according to all national laws
and regulations.

יצראה למשחה יקוח םואית

!הרהזא

תנקתה םייצראהו םיימוקמה למשחה יקוחל תמאות תויהל תבייח דויצה.

ﺕﺍﺪﻌﻤﻟﺍ ﺐﻴﻛﺮﺗ ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﻠﻟ ﻞﺜﺘﻤﻳ ﻥﺃ ﺐﺠﻳ ﻦﻴﻧﺍﻮﻘﺔﻴﻨﻁﻮﻟﺍﻭ ﺔﻴﻠﺤﻤﻟﺍ ﺔﻘﻠﻌﺘﻤﻟﺍ

ءﺎﺑﺮﻬﻜﻟﺎﺑ

Attention
L'équipement doit être installé conformément aux normes électriques nationales

et locales.

경고!

현 지역 및 국가의 전기 규정에 따라 장비를 설치해야 합니다.

Waarschuwing
Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale

elektriciteitsvoorschriften.

製品の廃棄

この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が
あります。

4-16

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Waarschuwing
De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming

met alle nationale wetten en reglementen.

Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen

des Landes erfolgen.

¡Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y

reglamentos nacionales.

Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des

lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de
l'organisme compétent.

Warning!

The fans might still be turning when you remove the fan assembly from the chassis.
Keep fi ngers, screwdrivers, and other objects away from the openings in the fan
assembly's housing.

Hot Swap Fan Warning

רצומה קוליס

!הרהזא

ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס.הנידמה יקוח

ﻲﺋﺎﻬﻨﻟﺍ ﺺﻠﺨﺘﻟﺍ ﻦﻣ ﺞﺘﻨﻤﻟﺍ ﺍﺬﻫ ﻪﻌﻣ ﻞﻣﺎﻌﺘﻟﺍ ﻲﻐﺒﻨﻳ ﻟ ﺎﻘﻓﻭ ﻊﻴﻤﺠﺔﻴﻨﻁﻮﻟﺍ ﺢﺋﺍﻮﻠﻟﺍﻭ ﻦﻴﻧﺍﻮﻘﻟﺍ ﺪﻨﻋ

ファン・ホットスワップの警告

シャーシから冷却ファン装置を取り外した際、ファンがまだ回転している可能性がありま
す。ファンの開口部に、指、ドライバー、およびその他のものを近づけないで下さい。

4-17

Chapter 4: Warning Statements for AC Systems

Warnung
Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis

genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände
von den Öffnungen des Lüftergehäuses entfernt.

¡Advertencia!
Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador

del chasis. Mandtenga los dedos, los destornilladores y todos los objetos lejos de
las aberturas del ventilador

Attention
Il est possible que les ventilateurs soient toujours en rotation lorsque vous retirerez

le bloc ventilateur du châssis. Prenez garde à ce que doigts, tournevis et autres
objets soient éloignés du logement du bloc ventilateur.

!הרהזא

יקלח תא םיריסמ רשאכ שי .םידבוע ןיידע םיררוואמהו ןכתי ,זראמהמ ררוואמה

קיחרהללררוואמה ךותב םיחתפהמ םינוש הדובע ילכו תועבצאה תא חוטב קחרמ

ﻦﻜﻤﻤﻟﺍ ﻦﻣ ﺡﻭﺍﺮﻤﻟﺍ ﻥﺃ ﻝﺍﺰﺗ ﻻ ﺔﻟﺍﺯﺇ ﺪﻨﻋﺭﻭﺪﺗ ﺔﻠﺘﻛ ﺔﺣﻭﺮﻤﻟﺍ ﻞﻜﻴﻬﻟﺍ ﻦﻣ ﺐﺠﻳ ءﺎﻘﺑﺇ

ﻊﺑﺎﺻﻷﺍ ﻭﻲﻏﺍﺮﺒﻟﺍ ﺕﺎﻜﻔﻣ

. ءﺎﻴﺷﻷﺍ ﻦﻣ ﺎﻫﺮﻴﻏﻭ ﺍﺪﻴﻌﺑ ﻦﻋ ﺕﺎﺤﺘﻔﻟﺍ ﻲﻓ ﺔﻠﺘﻛ ﺔﺣﻭﺮﻤﻟﺍ

경고!

섀시로부터 팬 조립품을 제거할 때 팬은 여전히 회전하고 있을 수 있습니다. 팬
조림품 외관의 열려있는 부분들로부터 손가락 및 스크류드라이버, 다른 물체들이
가까이 하지 않도록 배치해 주십시오.

Waarschuwing
Het is mogelijk dat de ventilator nog draait tijdens het verwijderen van het

ventilatorsamenstel uit het chassis. Houd uw vingers, schroevendraaiers
en eventuele andere voorwerpen uit de buurt van de openingen in de
ventilatorbehuizing.

4-18

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Warning!

When installing the product, use the provided or designated connection cables,
power cables and AC adaptors. Using any other cables and adaptors could cause
a malfunction or a fi re. Electrical Appliance and Material Safety Law prohibits the
use of UL or CSA -certifi ed cables (that have UL/CSA shown on the code) for any
other electrical devices than products designated by Supermicro only.

Power Cable and AC Adapter

Warnung
Bei der Installation des Produkts, die zur Verfügung gestellten oder benannt

Anschlusskabel, Stromkabel und Netzteile. Verwendung anderer Kabel und Adapter
kann zu einer Fehlfunktion oder ein Brand entstehen. Elektrische Geräte und
Material Safety Law verbietet die Verwendung von UL-oder CSA-zertifi zierte Kabel,
UL oder CSA auf der Code für alle anderen elektrischen Geräte als Produkte von
Supermicro nur bezeichnet gezeigt haben.

¡Advertencia!
Al instalar el producto, utilice los cables de conexión previstos o designados, los

cables y adaptadores de CA. La utilización de otros cables y adaptadores podría
ocasionar un mal funcionamiento o un incendio. Aparatos Eléctricos y la Ley de
Seguridad del Material prohíbe el uso de UL o CSA cables certifi cados que tienen
UL o CSA se muestra en el código de otros dispositivos eléctricos que los productos
designados por Supermicro solamente.

電源コードとACアダプター

製品を設置する場合、提供または指定された接続ケーブル、電源コードとACアダプター
を使用下さい。他のケーブルやアダプタを使用すると故障や火災の原因になることがあ

ります。電気用品安全法は、ULまたはCSA認定のケーブル(UL/CSEマークがコードに表

記)をSupermicroが指定する製品以外に使用することを禁止しています。

4-19

Chapter 4: Warning Statements for AC Systems

Attention
Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné.

L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement
ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit
l'utilisation de UL ou CSA câbles certifi és qui ont UL ou CSA indiqué sur le code
pour tous les autres appareils électriques que les produits désignés par Supermicro
seulement.

אתמו םיילמשחמ י

AC

!הרהזא

םימאתמו םיקפס ,םילבכב שמתשהל שי ,רצומה תא םיניקתמ רשאכAC רשא

וא הלקתל םורגל לוכי רחא םאתמ וא לבכ לכב שומיש .ךכ םשל וקפוסו ודעונ

טב יקוחו למשח ירישכמב שומיש יקוח יפ לע .ילמשח רצק רוסיא םייק ,תוחי

ב םיכמסומה םילבכב שמתשהל-

UL ב וא- CSA לש דוק םהילע עיפומ ראשכ)

UL/CSA( רחא ילמשח רצומ לכ רובע.דבלב ורקימקרפוס ידי לע ןיוצ אלש

ﺐﻴﻛﺮﺗ ﺪﻨﻋ ﻡﺍﺪﺨﺘﺳﺍ ﺐﺠﻳ ﺯﺎﻬﺠﻟﺍ ﻭ،ﻞﻴﺻﻮﺘﻟﺍ ﺕﻼﺑﺎﻛ ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﺕﻼﺑﺎﻜﻟﺍ

ﺕﻻﻮﺤﻣﻭ ﺩﺩﺮﺘﻤﻟﺍ ﺭﺎﻴﺘﻟﺍ

. ﻥﺃ ﻱﺃ ﻡﺍﺪﺨﺘﺳﺍ ﺕﻼﺑﺎﻛ ﺕﻻﻮﺤﻣﻭ ﻯﺮﺧﺃ ﺐﺒﺴﺘﻳ ﻲﻓ ﻞﻄﻋ ﺙﻭﺪﺣ ﻖﻳﺮﺣ ﻭﺃ . ﻲﺘﻟﺍ

ﻚﻟ ﺎﻫﺮﻴﻓﻮﺗ ﻢﺗ ﺞﺘﻨﻤﻟﺍ ﻊﻣ

UL ﻭﺃ CSA ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﺓﺰﻬﺟﻷﺍ ﺩﺍﻮﻣﻭ ﻥﻮﻧﺎﻗ ﺔﻣﻼﺴﻟﺍ ﻡﺍﺪﺨﺘﺳﺍ ﺮﻈﺤﻳ ﺕﻼﺑﺎﻜﻟﺍ

ﻞﺒﻗ ﻦﻣ ﺓﺪﻤﺘﻌﻣ

Supermicro ﺓﺰﻬﺟﺃ ﻯﺮﺧﺃ ﺔﻴﺋﺎﺑﺮﻬﻛ ﺮﻴﻏ ﺕﺎﺠﺘﻨﻤﻟﺍ ﺔﻨﻴﻌﻤﻟﺍ ﻞﺒﻗ ﻦﻣ ﻱﻷ

(UL/CSA ﻞﻤﺤﺗ ﻲﺘﻟﺍﺔﻣﻼﻋ )

경고!

제품을 설치할 때에는 제공되거나 지정된 연결케이블과 전원케이블, AC어댑터를
사용해야 합니다. 그 밖의 다른 케이블들이나 어댑터들은 고장 또는 화재의 원인이
될 수 있습니다. 전기용품안전법 (Electrical Appliance and Material Safety
Law)은 슈퍼마이크로에서 지정한 제품들 외에는 그 밖의 다른 전기 장치들을
위한 UL또는 CSA에서 인증한 케이블(전선 위에 UL/CSA가 표시)들의 사용을
금지합니다.

Waarschuwing
Bij het installeren van het product, gebruik de meegeleverde of aangewezen kabels,

stroomkabels en adapters. Het gebruik van andere kabels en adapters kan leiden
tot een storing of een brand. Elektrisch apparaat en veiligheidsinformatiebladen wet
verbiedt het gebruik van UL of CSA gecertifi ceerde kabels die UL of CSA die op
de code voor andere elektrische apparaten dan de producten die door Supermicro
alleen.

4-20

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Notes

Chapter 5: Advanced Serverboard Setup

5-1

Chapter 5

Advanced Serverboard Setup

This chapter covers the steps required to install the X9DRT-IBQF/IBFF/F
serverboard into the chassis, connect the data and power cables and install add-on
cards. All serverboard jumpers and connections are also described. A layout and
quick reference chart are included in this chapter for your reference. Remember to
completely close the chassis when you have fi nished working with the serverboard
to better cool and protect the system.

5-1 Handling the Serverboard

Electrostatic Discharge (ESD) can damage electronic com ponents. To prevent
damage to any printed circuit boards (PCBs), it is important to handle them very
carefully (see previous chapter). To prevent the serverboard from bending, keep
one hand under the center of the board to support it when handling. The following
measures are generally suffi cient to protect your equipment from electric static
discharge.

Precautions

• Use a grounded wrist strap designed to prevent Electrostatic Discharge (ESD).

• T ouch a grounded metal object before removing any board from its antistatic bag.

• Handle a board by its edges only; do not touch its components, peripheral chips,

memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the serverboard, add-on cards and peripherals back into their antistatic

bags when not in use.

• For grounding purposes, make sure your computer chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and
the serverboard.

Unpacking

The serverboard is shipped in antistatic packaging to avoid electrical static
discharge. When unpacking the board, make sure the person handling it is static
protected.

5-2

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

5-3 Control Panel Connectors and I/O Ports

The rear I/O ports are color coded in conformance with the PC 99 specifi cation. See
Figure 5-1 below for the colors and locations of the various I/O ports.

Figure 5-1. Rear I/O Ports

2

1 5

3

4 6

7

98

5-2 Connecting Cables

Now that the processors are installed, the next step is to connect the cables to
the serverboard.

Connecting Data Cables

The cables used to transfer data from the peripheral devices have been carefully
routed in preconfi gured systems to prevent them from blocking the fl ow of cooling
air that moves through the system from front to back. If you need to disconnect
any of these cables, you should take care to reroute them as they were originally
after reconnecting them (make sure the red wires connect to the pin 1 locations). If
you are confi guring the system, keep the airfl ow in mind when routing the cables.

The following cables need to be connected for the SuperServer 6017TR-TQF/TFF/TF
system:

• Two round 50-cm 16-to-16-pin ribbon front control cables (CBL-0087)

• One set of SATA 4-51/47/41/37-cm round cables (CBL-0201L)

• Two 4-pin 20-cm power cables (CBL-0212L)

Chapter 5: Advanced Serverboard Setup

5-3

Back Panel I/O Port Locations and Defi nitions

1. Back Panel USB Port 0

2. Back Panel USB Port 1

3. IPMI_Dedicated LAN

4. Gigabit LAN 1

5. Gigabit LAN 2

6. COM Port 1 (Turquoise)

7. Back Panel VGA (Blue)

8. Infi niBand Connector (For X9DRT-IBQF/X9DRT-IBFF)

9. UID Switch

Connecting the Control Panel

JF1 contains header pins for various front control panel connectors. See Figure 5-1
for the pin locations of the various front control panel buttons and LED indicators.
Even and odd numbered pins are on opposite sides of each header.

All JF1 wires have been bundled into single keyed ribbon cable to simplify their
connection. The red wire in the ribbon cable plugs into pin 1 of JF1. Connect the
other end of the cable to the Control Panel printed circuit board, located just behind
the system status LEDs in the chassis.

See the Connector Defi nitions section in this chapter for details and pin descriptions
of JF1.

Figure 5-2. Front Control Panel Header Pins (JF1)

NMI
x (key)

3.3 V
ID_UID_SW/3/3V Stby
NIC1 Activity LED
NIC2 Activity LED
Red+ (Blue LED Cathode)

3.3V
Reset Button
Power Button

Ground

x (key)

FP Power LED

HDD LED
NIC1 Activity LED
NIC2 Activity LED

Blue + [OH/Fan Fail/PWR Fail/UID LED]

Power Fail LED

Ground
Ground

2 1

20 19

5-4

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Installing the LGA2011 Processor

1. There are two load levers on the LGA2011 socket. To open the socket cover,
fi rst press and release the load lever labeled 'Open 1st'.

OPEN 1st

OPEN 1st

Press down on

Load Lever

labeled 'Open 1st'.

OPEN 1st

OPEN 1st

5-4 Processor and Heatsink Installation

Caution! When handling the processor package, avoid placing direct pressure on the

label area.
Note: Always connect the power cord last, and always remove it before adding,

removing or changing any hardware components. Make sure that you install the
processor into the CPU socket before you install the CPU heatsink.

Caution! If you buy a CPU separately, make sure that you use an Intel-certifi ed multi-
directional heatsink only.

Note: Make sure to install the system board into the chassis before you install the
CPU heatsink.

Note: When receiving a server board without a processor pre-installed, make sure that
the plastic CPU socket cap is in place and none of the socket pins are bent; otherwise,
contact your retailer immediately.

Note: Refer to the Supermicro website for updates on CPU support.
Note: When one CPU is installed, be sure to installed on CPU Socket 1 fi rst.

Note: Graphics and drawings shown in this manual are for illustration only. Your

components may or may not look the same as the graphics shown in the manual.

Chapter 5: Advanced Serverboard Setup

5-5

2. Press the second load lever labeled 'Close 1st' to release the load plate that
covers the CPU socket from its locking position.

OPEN 1st

OP

EN

1s

t

OPEN 1st

OPEN 1st

Press down on

Load the Lever

labeled 'Close 1st

'

Pull lever away

from the socket

3. With the lever labeled 'Close 1st' fully retracted, gently push down on
the 'Open 1st' lever to open the load plate. Lift the load plate to open it
completely.

Gently push down to pop the

load plate open.

OPEN 1st

OPEN

1s

t

4. Using your thumb and the index fi nger, remove the 'WARNING' plastic cap
from the socket.

5-6

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

5. Use your thumb and index fi nger to hold the CPU on its edges. Align the CPU
keys, which are semi-circle cutouts, against the socket keys.

Socket Keys

CPU Keys

6. Once they are aligned, carefully lower the CPU straight down into the socket.
(Do not drop the CPU on the socket. Do not move the CPU horizontally or
vertically. Do not rub the CPU against the surface or against any pins of the
socket to avoid damaging the CPU or the socket.)

Caution: You can only install the CPU inside the socket in one direction. Make sure
that it is properly inserted into the CPU socket before closing the load plate. If it doesn't
close properly, do not force it as it may damage your CPU. Instead, open the load
plate again and double-check that the CPU is aligned properly.

Chapter 5: Advanced Serverboard Setup

5-7

7. With the CPU inside the socket, inspect the four corners of the CPU to make
sure that the CPU is properly installed.

8. Close the load plate with the CPU inside the socket. Lock the lever labeled
'Close 1st' fi rst, then lock the lever labeled 'Open 1st' second. Use your
thumb to gently push the load levers down to the lever locks.

OPEN 1st

OPEN

1st

Push down and lock the
level labeled 'Close 1st'.

Gently close the

load plate.

OPEN 1st

OPEN 1s

t

OPEN 1st

OPEN 1st

Lever Lock

Lever Lock

Push down and lock

the lever labeled

'Open 1st'

5-8

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Installing a Passive CPU Heatsink

1. Apply the proper amount of thermal grease to the heatsink.

2. Place the heatsink on top of the CPU so that the two mounting holes on the
heatsink are aligned with those on the retention mechanism.

3. Instal l two sc rews on e ach si de of the he atsink t hroug h the mou nting ho les
on the se rve rboa rd, and tu rn the p ush- pins c loc kw ise to lo ck the m.

Note: Graphic drawings included in this manual are for reference only. They might
look different from the components installed in your system.

OPEN 1st

Direction of Airfl ow

Screw#1

Screw#2

Screw#3

Screw#4

Screw#1

Screw#2

Screw#3

Screw#4

Chapter 5: Advanced Serverboard Setup

5-9

Removing the Heatsink

Caution: W e DO NOT recommend that the CPU or the heatsink be removed. However ,

if you do need to uninstall the heatsink, please follow the instructions below to uninstall
the heatsink to prevent damage done to the CPU or the CPU socket.

1. Unplug the power cord from the power supply.

2. Press down the screw on the heatsink, and turn counter-clock-wise to loosen
it. Repeat the same step to loosen the second screw.

3. Hold the heatsink as shown in the picture below, and gently wriggle the
heatsink to loosen it. (Do not use excessive force when wriggling the
heatsink.)

4. Once the heatsink is loosened, remove it from the serverboard.

Note: To reinstall the CPU and the heatsink, clean the surface of the CPU and the
heatsink to get rid of the old thermal grease. Reapply the proper amount of thermal
grease on the surface before reinstalling them on the serverboard.

OPEN 1st

Direction of Airfl ow

5-10

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

5-5 Installing Memory

Caution: exercise extreme care when installing or removing DIMM modules to prevent

any possible damage.

Installing Memory

1. Insert the desired number of DIMMs into the memory slots, starting with P1­DIMM #A1. Push the release tabs outwards on both ends of the DIMM slot to
unlock it.

2. Align the key of the DIMM module with the receptive point on the memory
slot.

3. Align the notches on both ends of the module against the receptive points on
the ends of the slot.

4. Use two thumbs together to press the notches on both ends of the module
straight down into the slot until the module snaps into place.

5. Press the release tabs to the locking positions to secure the DIMM module
into the slot.

Note: 512 MB, 1 GB, 2 GB, 4 GB, 8 GB, 16 GB or 32 GB size memory modules
are supported. It is highly recommended that you remove the power cord from the
system before installing or changing memory modules. Please refer to our web site
for memory that has been tested on the X9DRT-IBQF/IBFF/F serverboard.

Removing Memory Modules

Press both notches on the ends of the DIMM module to unlock it. Once the DIMM
module is loosened, remove it from the memory slot.

Memory Support

The X9DRT-IBQF/IBFF/F serverboard supports DDR3-1600/1333/1066/800 MHz
speed registered ECC/Unbuffered ECC/non-ECC SDRAM. Populating two slots at
a time with memory modules of the same size and type will result in interleaved
(128-bit) memory, which is faster than non-interleaved (64-bit) memory.”

Note: Check the Supermicro website (www.supermicro.com) for the latest memory
support information.

Maximum Memory

The X9DRT-IBQF/IBFF/F serverboard supports up to 256 GB of ECC 240-pin
Registered (RDIMM)/Load Reduced (LRDIMM) ECC memory or up to 64 GB of
Unbuffered (UDIMM) non-ECC memory in eight (8) DIMM slots.

Chapter 5: Advanced Serverboard Setup

5-11

Processors and their Corresponding Memory

Modules
CPU# Corresponding DIMM Modules
CPU1

P1-DIMMA1 P1-DIMMB1 P1-DIMMC1 P1-DIMMD1

CPU2

P2-DIMME1 P2-DIMMF1 P2-DIMMG1 P2-DIMMH1

Processor and Memory Module Population

Number of
CPUs+DIMMs

CPU and Memory Population Confi guration Table
(*For memory to work proper, please install DIMMs in
pairs)

1 CPU &
2 DIMMs

CPU1
P1-DIMMA1/P1-DIMMB1

1 CPU &
4 DIMMs

CPU1
P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1

2 CPUs &
4 DIMMs

CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1

2 CPUs &
6 DIMMs

CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1

2 CPUs &
8 DIMMs

CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2­DIMMG1/P2-DIMMH1

To Install: Insert
module vertically and
press down until it
snaps into place.
Pay attention to the
alignment notch at
the bottom.

To Remove: Use
your thumbs to gently
push the release tabs
near both ends of the
module. This should
release it from the
slot.

Top View of DDR3 Slot

Release Tab Release Tab

Note: Notch should align with

the receptive key point on
the slot.

Notch

Notch

Front View

Figure 5-3. Installing DIMM into Slot

5-12

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

DIMM Module Population Confi guration

For memory to work properly, follow the tables below for memory installation:

Installing UDIMM (ECC/Non-ECC) Memory

Intel E5-2600 Series Processor UDIMM Memory Support

Ranks Per DIMM
& Data Width

Memory Capacity
Per DIMM

(See the Note
below)

Speed (MT/s) and Voltage Validated by
Slot per Channel (SPC) and DIMM Per
Channel (DPC)

1 Slot Per Channel
1DPC

1.35V 1.5V

SRx8 Non-ECC

1GB 2GB 4GB NA 1066,1333, 1600

DRx8 Non-ECC

2GB 4GB 8GB NA 1066,1333, 1600

SRx16 Non-ECC

512MB 1GB 2GB NA 1066,1333, 1600

SRx8 ECC

1GB 2GB 4GB 1066, 1333 1066,1333, 1600

DRx8 ECC

2GB 4GB 8GB 1066, 1333 1066,1333, 1600

Note: For detailed information on memory support and updates, please refer to the SMC Recommended
Memory List posted on our website at http://www.supermicro.com/support/resources/mem.cfm.

Installing RDIMM (ECC) Memory

Intel E5-2600 Series Processor RDIMM Memory Support

Ranks Per
DIMM &
Data Width

Memory
Capacity
Per DIMM

(See the Note
Below)

1 Slot Per Channel
1DPC

1.35V 1.5V

SRx8

1GB 2GB 4GB 1066, 1333 1066, 1333,1600

DRx8

2GB 4GB 8GB 1066, 1333 1066,1333, 1600

SRx4

2GB 4GB 8GB 1066, 1333 1066,1333, 1600

DRx4

4GB 8GB 16GB 1066, 1333 1066,1333, 1600

QRx4

8GB 16GB 32GB 800 1066

QRx8

4GB 8GB 16GB 800 1066

Note: For detailed information on memory support and updates, please refer to the SMC
Recommended Memory List posted on our website at http://www.supermicro.com/support/

resources/mem.cfm.

Chapter 5: Advanced Serverboard Setup

5-13

Installing LRDIMM (ECC) Memory

Intel E5-2600 Series Processor LRDIMM Memory Support

Ranks Per
DIMM &
Data Width

(See the
Note
Below)

Memory Capacity
Per DIMM

Speed (MT/s) and Voltage
Validated by Slot per Channel
(SPC) and DIMM Per Channel
(DPC)

1 Slot Per Channel
1DPC

1.35V 1.5V

QRx4 (DDP)

16GB 32GB 1066,1333 1066,1333

QRx8 (P)

8GB 16GB 1066,1333 1066,1333

Note: For detailed information on memory support and updates, please refer to the SMC
Recommended Memory List posted on our website at http://www.supermicro.com/support/

resources/mem.cfm.

Note 1: For the memory modules to work properly, please install DIMM modules
of the same type, same speed and same operating frequency on the serverboard.
Mixing of RDIMMs, UDIMMs or LRDIMMs is not allowed. Do not install both ECC
and Non-ECC memory modules on the same serverboard.

Note 2: Using DDR3 DIMMs with different operating frequencies is not allowed.

Possible System Memory Allocation & Availability

System Device Size Physical Memory

Available
(4 GB Total System
Memory)

Firmware Hub fl ash memory (System BIOS) 1 MB 3.99 GB
Local APIC 4 KB 3.99 GB
Area Reserved for the chipset 2 MB 3.99 GB
I/O APIC (4 Kbytes) 4 KB 3.99 GB
PCI Enumeration Area 1 256 MB 3.76 GB
PCI Express (256 MB) 256 MB 3.51 GB
PCI Enumeration Area 2 (if needed) -Aligned on 256-M

boundary-

512 MB 3.01 GB

VGA Memory 16 MB 2.85 GB
TSEG 1 MB 2.84 GB
Memory available for the OS & other applications 2.84 GB

5-14

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

5-6 Adding PCI Expansion Cards

The 6017TR-TQF/TFF/TF includes one preinstalled riser card per node designed
specifi cally for use in the SC808BT-1K28BP 1U rackmount chassis. These riser
cards support one low-profi le PCI Express x16 cards to fi t inside the chassis for
each node.

Installing an Expansion Card

1. After powering down the system, remove the PCI slot shield.

2. Fully seat the card into the slot, pushing down with your thumbs evenly on
both sides of the card.

3. Finish by using a screw to secure the top of the card shield to the chassis.
The PCI slot shield protects the serverboard and its components from EMI
and aid in proper ventilation, so make sure it is always in place.

Chapter 5: Advanced Serverboard Setup

5-15

5-7 Serverboard Details

Figure 5-4. X9DRT-IBQF/IBFF/F Serverboard Layout

(not drawn to scale)

X9DRT-F

Rev. 1.01A

USB0/1

IPMI_LAN

LAN1

LAN2

COM1

VGA

LEM1

JIB1

JBR1

InfiniBand

UID

LE2

LEB1

LEB2

JI2C2

JI2C1

JWD1

CPU1 PCI-E 3.0 x16

I-SATA0

I-SATA1

I-SATA2

I-SATA3

I-SATA4

I-SATA5

JSD1

P1-DIMMA1

P1-DIMMB1

P2-DIMMH1

P2-DIMMG1

J23

JP8

Fan1

LE1

BIOS

Fan3

P2-DIMMF1

P2-DIMME1

Fan4

JPI2C1

(4-Pin PWR)

(20-Pin PWR)

(20-Pin PWR)

J24

JF1

FPCTRL

P1-DIMMC1

P1-DIMMD1

T-SGPIO1

JBT1

JVRM_I2C2

JVRM_I2C1

JIPMB1

USB2

JPG1

JPL1

JPTM1

JPB1

JBAT1

CPU2

CPU1

SW1

PCH

C602J

BMC

LAN

CTRL

IB

CTRL

Processor

#1

Processor

#2

CLOSE 1st

OPEN 1st

CLOSE 1st

OPEN 1st

5-16

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Notes:

1. For the latest CPU/Memory updates, please refer to our website at http://

www.supermicro.com/products/serverboard/ for details.

2. Use only the correct type of onboard CMOS battery as specifi ed by the
manufacturer. Do not install the onboard battery upside down to avoid
possible explosion.

3. Jumpers not indicated are for test purposes only.

4. All graphics shown in this manual were based upon the latest PCB Revision
available at the time of publishing of the manual. The serverboard you've
received may or may not look exactly the same as the graphics shown in this
manual.

X9DRT-IBQF/IBFF/F Quick Reference

Jumper Description Default Setting

JBT1 Clear CMOS See page 5-25
JIB1 Infi niBand Enable/Disable

(X9DRT-IBQF/X9DRT-IBFF only)

Pins 1-2 (Enabled)

JI2C1/
JI2C2

SMB to PCI-E Slots Pins 2-3 (Normal)

JPB1 BMC Enable/Disable Pins 1-2 (Enabled)
JPG1 VGA Enable/Disable Pins 1-2 (Enabled)
JPL1 Ethernet GLAN1/GLAN2 Enable/

Disable

Pins 1-2 (Enabled)

JWD1 Watch Dog Pins 1-2 (Reset)

LED Description State Status

LE1

Onboard PWR
LED

Green: On Onboard PWR On
LE2 UID LED Blue: On Unit Identifi ed
LEB1/

LEB2

Infi niBand LED On

IB Connected
(X9DRT-IBQF and X9DRT-IBFF
only)

Chapter 5: Advanced Serverboard Setup

5-17

LEM1

BMC Heartbeat
LED

Green: Blinking BMC Normal

Connector Description

IB Infi niBand Connector (X9DRT-IBQF and X9DRT-IBFF only)
I-SATA 0/5 Intel PCH SATA Connectors 0-5 (SATA 3.0 Ports 0/1, SATA 2.0

Ports 2-5)

FAN 1, FAN
3/4

CPU/System Fan Headers (Fan1, Fan3, Fan4)

J23/J24 20-Pin Main Power Connectors
JBAT1 Onboard Battery (See the warning on P. 1-6.)
JF1 Front Panel Control Header
JIPMB1 4-pin External BMC I

2

C Header (for an IPMI Card)
JP8 4-Pin Auxiliary Power Connector
JPI2C1 Power Supply SMBbus I2C Header
JTPM1 TPM (Trusted Platform Module)/Port 80
JSD1 SATA DOM (Device_On_Module) Power Connector
LAN1/2 G-bit Ethernet Ports 1/2
(IPMI) LAN IPMI_Dedicated LAN
Slot1 PCI-E 3.0 x16 Slot for SMC-Proprietary Riser Card (Available

when CPU1 is installed)
T-SGPIO 1 Serial link General Purpose I/O Connection 1
UID SW UID (Unit Identifi er) Switch
USB 0/1 Back Panel USB 0/1
USB 2 Type-A Onboard USB 2.0 Connector
VGA Backpanel VGA Port

Note: The X9DRT-F/-IBQF/-IBFF serverboard supports proprietary power
connectors.

5-18

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

5-8 Connector Defi nitions

Power Connectors

Two 20-pin main power supply
connectors (J23/J24) and a 4-pin power
connector (JP8) are located on the
serverboard. These power connectors
meet the SSI EPS 12V specifi cation. For
power supply to work properly, please
follow the instructions given below. See
the table on the right for pin defi nitions.

Note 1: Y ou cannot use both 20-pin power
connectors: PWR1 (the right connector)
and PWR2 (the left connector) as input
power supply at the same time. Only
one connector can be used for input
power supply to the serverboard at a
time. For proper use of these proprietary
PWR Connectors, please customize
your PWR cables based on Supermicro
PWR Connector Pin-Out Definitions
listed above.

Note 2: The black square (dot) on a
power connector indicates the location
of Pin 1.

ATX Power 20-pin Connector

Pin Defi nitions (J23/J24)

Pin# Defi nition Pin# Defi nition
1 GND 11 PS_ON_N
2 GND 12 5V_STBY
3 GND 13 GND
4 GND 14 GND
5 GND 15 GND
6NC 16NC
7 12V 17 12V
8 12V 18 12V
9 12V 19 12V
10 12V 20 12V

4-pin Auxiliary Power Connector

In addition to two 20-pin power
connectors, a 4-pin 12V PWR supply
is located at JP8 on the serverboard.
This power connector is used to provide
power supply to hard drive disks. Refer
to the layout below for the location.

Note1: The 4-pin Auxiliary Power
Connector is used for power supply
output to HDDs only.

Note 2: The black square (dot) on the
power connector indicates the location
of Pin 1.

4-Pin PWR

Pin Defi nitions (JP8)

Pin# Defi nition
1 +12V
2 Ground
3 Ground
4 +5V

Chapter 5: Advanced Serverboard Setup

5-19

Reset Connector

The reset connector is located on pins 3
and 4 of JF1 and attaches to the reset
switch on the computer chassis. See the
table on the right for pin defi nitions.

PW_ON Connector

The Power Button connection is located
on pins 1 and 2 of JF1. Momentarily
contacting both pins will power on/off
the system. This button can also be
configured to function as a suspend
button (with a setting in the BIOS - See
Chapter 5). To turn off the power when
the system is in suspend mode, press
the button for 4 seconds or longer. Refer
to the table on the right for pin defi nitions.

Reset Button

Pin Defi nitions

(JF1)

Pin# Defi nition
3 Reset
4 Ground

Power Button

Pin Defi nitions

(JF1)

Pin# Defi nition
1 PW_ON
2 Ground

Blue + [OH/Fan Fail/PWR Fail/UID
LED]

Connect an LED cable to pins 7 and
8 of Front Control Panel to use the
Overheat/Fan Fail/Power Fail and UID
LED connections. The Red LED on
pin 7 provides warnings of overheat,
fan failure or power failure. The Blue
LED on pin 8 wor ks as the front pan el
UID LED in dicato r. The Red LED takes
precedence over the Blue LED by
default. Refer to the table on the right
for pin de fi nitions.

Blue + [OH/Fan Fail/PWR Fail/UID

LED] Pin Defi nitions (JF1)

Pin# Defi nition
7 Red_LED-Cathode/OH/Fan

Fail/Power Fail5.5V.SB

8 Blue_UID LED

OH/Fan Fail/PWR Fail LED

Status (Red LED)

State Indication
Off Normal
On Overheat
Flashing Fan Fail

Power Fail LED

The Power Fail LED connection is
locate d on pi ns 5 an d 6 of JF1. Refer to
the tab le on th e ri ght for p in defi nitions.

PWR Fail LED

Pin Defi nitions (JF1)

Pin# Defi nition
5 3.3V
6 PWR Supply Fail

5-20

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

NMI Button

The non-maskable interrupt button
header is located on pins 19 and 20 of
JF1. Refer to the table on the right for
pin defi nitions.

NMI Button

Pin Defi nitions

(JF1)

Pin# Defi nition
19 Control
20 Ground

HDD LED

The HDD LED connection is located
on pins 13 and 14 of JF1. Attach the
hard drive LED cable here to display
disk activity (for any hard drives on
the system, including Serial ATA and
IDE). See the table on the right for pin
defi nitions

HDD LED

Pin Defi nitions

(JF1)

Pin# Defi nition
13 3.3V Standby
14 HD Active

Power On LED

The Power On LED connector is located
on pins 15 and 16 of JF1. This connection
is used to provide LED indication of
power being supplied to the system. See
the table on the right for pin defi nitions.

Power LED

Pin Defi nitions

(JF1)

Pin# Defi nition
15 3.3V
16 PWR LED

NIC1 LED

Pin Defi nitions (JF1)

Pin# Defi nition
9 NIC 2 Activity LED
10 NIC 2 Link LED
11 NIC 1 Activity LED
12 NIC 1 Link LED

NIC1 (LAN1) LED

The NIC (Network Interface Controller)
LED connections for GLAN port 1 are
located on pins 11 and 12 of JF1, and
the LED connection for GLAN Port 2 are
on Pins 9 and 10. Attach the NIC LED
cables here to display network activity.
Refer to the table on the right for pin
defi nitions.

Video Connector

A Video (VGA) connector is located next
to the COM Port on the IO backplane.
This connector is used to provide video
and CRT display.

Chapter 5: Advanced Serverboard Setup

5-21

Serial Ports

The COM1 serial port is located beside
the VGA port. Refer to the serverboard
layout for the location of the COM2
header. See the table on the right for
pin defi nitions.

Serial Port Pin Defi nitions

(COM1/COM2)

Pin # Defi nition Pin # Defi nition
1 DCD 6 DSR
2 RXD 7 RTS
3 TXD 8 CTS
4 DTR 9 RI
5 Ground 10 NC

NC indicates no connection.

Infi niBand Connection

Both the X9DRT-IBQF and
X9DRT-IBFF serverboards have an
onboard Infi niBand (IB) connector,
which is located on the rear IO panel
on the serverboard. The IB switch is
primarily used for High-performance
computing. See the table on the right
for pin defi nitions.

Infi niBand (IB)

Pin Defi nitions

Pin # Defi nition Pin # Defi nition
S1 Input Pair0:Pos S9 Output Pair3:Pos

S2 Input Pair0:Neg S10 Output Pair3:Neg
S3 Input Pair1:Pos S11 Output Pair2:Pos
S4 Input Pair1:Neg S12 Output Pair2:Neg
S5 Input Pair2:Pos S13 Output Pair1:Pos
S6 Input Pair2:Neg S14 Output Pair1:Neg
S7 Input Pair3:Pos S15 Output Pair0:Pos
S8 Input Pair3:Neg S16 Output Pair0:Neg

G8

G9

G1G2G3G4G5G6G7

S1S2S3S4S5S6S7S8S9

S10

S11

S12

S13

S14

S15

S16

Infi niBand Ground Pins
(G1~G9) Pin Defi nitions

Pin# Defi nitions
G1~G9 Ground

Fan Header (Fan1/3/4)

Pin Defi nitions

Pin# Defi nition
1 Ground
2 +12V
3 Tachometer
4 PWR Modulation

Fan Headers

This serverboard has three system/CPU
fan headers (Fan 1, Fan 3, and Fan 4)
on the serverboard. All these 4-pin fans
headers are backward compatible with
the traditional 3-pin fans. The fan speeds
are controlled by fi rmware management
via IPMI interface. See the table on the
right for pin defi nitions.

5-22

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

IPMB I

2

C SMB

A System Management Bus header
for the IPMI slot is located at JIPMB1.
Connect an appropriate cable here to
use the IPMB I

2

C connection on your

system.

SMB Header (JIPMB1)

Pin Defi nitions

Pin# Defi nition
1 Data
2 Ground
3 Clock
4 No Connection

Power SMB (I2C) Connector

Power System Management Bus (I2C)
Connector (JPI2C1) monitors power
supply, fan and system temperatures.
See the table on the right for pin
defi nitions.

PWR SMB (JPI2C1)

Pin Defi nitions

Pin# Defi nition
1 Clock
2 Data

3 PWR Fail
4 Ground
5 +3.3V

TPM Header/Port 80

A Trusted Platform Module/Port 80
header is located at JTPM1 to provide
TPM support and Port 80 connection.
Use this header to enhance system
performance and data security. See the
table on the right for pin defi nitions.

TPM/Port 80 Header (JTPM1)

Pin Defi nitions

Pin# Defi nition Pin# Defi nition
1 LCLK 2 GND
3 LFRAME# 4 <(KEY)>
5 LRESET# 6 +5V (X)
7 LAD 3 8 LAD 2
9 +3.3V 10 LAD1
11 LAD0 12 GND
13 SMB_CLK4 14 SMB_DAT4
15 +3V_DUAL 16 SERIRQ
17 GND 18 CLKRUN# (X)
19 LPCPD# 20 LDRQ# (X)

SATA DOM Power Connector

A power connector for SATA DOM
(Disk_On_Module) devices is located
at JSD1. Connect an appropriate cable
here to provide power support for your
SATA DOM devices.

DOM PWR (JSD1)

Pin Defi nitions

Pin# Defi nition
1 +5V
2 Ground
3 Ground

Chapter 5: Advanced Serverboard Setup

5-23

Ethernet LAN Ports

Two Gigabit Ethernet ports (LAN1/2)
are located on the I/O backplane on
the serverboard. In addition, an IPMI
Dedicated LAN is located above USB
0/1 ports on the backplane to provide
KVM support for IPMI 2.0. All these ports
accept RJ45 type cables.

Note: Please refer to the LED Indicator
Section for LAN LED information.

LAN Ports (LAN1/2)

Pin Defi nition

Pin# Defi nition Pin# Defi nition
1 P2V5SB 10 SGND
2 TD0+ 11 Act LED
3 TD0- 12 P3V3SB
4 TD1+ 13 Link 100 LED

(Yellow, +3V3SB)

5 TD1- 14 Link 1000 LED

(Yellow, +3V3SB)
6 TD2+ 15 Ground
7 TD2- 16 Ground
8 TD3+ 17 Ground
9 TD3- 18 Ground

NC indicates no connection.

Universal Serial Bus (USB)

Two Universal Serial Bus ports (USB
0/1) are located on the I/O back panel.
In addition, a Type USB 2.0 connector
(USB 2), located next to the BMC chip,
also provides onboard USB support
(cables are not included). See the tables
on the right for pin defi nitions.

USB (2)

Pin Defi nitions

USB 2
Pin# Defi nition

USB 3

Pin# Defi nition
1 +5V 1 +5V
2 PO- 2 PO­3 PO+ 3 PO+
4 Ground 4 Ground
5 NC 5 Key

NC indicates no connection.

Backplane USB

(USB 0/1)

Pin Defi nitions

Pin# Defi nition
1 +5V
2 PO­3 PO+
4 Ground
5NA

5-24

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Unit Identifi er Switches

Two Unit Identifi er (UID) Switches and
two LED Indicators are located on the
serverboard. The Front Panel UID Switch
is located at Pin 16 on JF2. The Rear
UID Switch is located at SW1 next to the
Infi niBand Connector. The Front Panel
UID LED is located at Pin 17 of JF2,
and the Rear UID LED is located at LE2.
When the user presses a UID switch on
the front panel or on the back panel, both
Rear UID LED and Front Panel UID LED
Indicators will be turned on. Press the
UID switch again to turn off both LED
Indicators. These UID Indicators provide
easy identifi cation of a system unit that
may be in need of service. See the table
on the right for pin defi nitions.

Note: UID LED is supported by the
physical switch or the BMC. When it is
controlled by the physical switch, it will
stay solid. When it is controlled by the
BMC, it will blink.

UID Switch

Pin# Defi nition
1 Ground
2 Ground
3 Button In
4 Ground

UID Switches & LEDs

Description Location
FP Switch Pin 16 on JF2
Rear Switch SW1
FP UID LED

(Blue LED)

Pin 17 on JF2

Rear UID LED LE2

T-SGPIO1 Header

A Serial Link General Purpose Input/
Output header (T-SGPIO 1) is located
at on the serverboard to provide support
for onboard SATA connections. See the
table on the right for pin defi nitions.

T-SGPIO

Pin Defi nitions

Pin# Defi nition Pin Defi nition
1NC 2NC
3 Ground 4 Data

5 Load 6 Ground
7 Clock 8 NC

Note: NC= No Connection

Chapter 5: Advanced Serverboard Setup

5-25

5-9 Jumper Settings

Explanation of Jumpers

To modify the operation of the serverboard,
jumpers can be used to choose between
optional settings. Jumpers create shorts
between two pins to change the function
of the connector. Pin 1 is identifi ed with
a square solder pad on the printed circuit
board. See the diagram at right for an
example of jumping pins 1 and 2. Refer to the
serverboard layout page for jumper locations.

Note: On two-pin jumpers, "Closed" means
the jumper is on and "Open" means the
jumper is off the pins.

Connector

Pins

Jumper

Setting

3 2 1

3 2 1

JBT1 contact pads

CMOS Clear

JBT1 is used to clear CMOS, which will also clear any passwords. Instead of pins,
this jumper consists of contact pads to prevent accidentally clearing the contents
of CMOS.

To Clear CMOS

1. First power down the system and unplug the power cord(s). It is also
recommended that you remove the onboard battery from the serverboard.

2. With the power disconnected, short the CMOS pads with a metal object such
as a small screwdriver.

3. Remove the screwdriver (or shorting device).

4. Reconnect the power cord(s) and power on the system.

Note: Do not use the PW_ON connector to clear CMOS.

Infi niBand (IB) Enable

Both the X9DRT-IBQF and X9DRT-IBFF
serverboards have Jumper JIB1, which
allows you to enable the onboard
Infi niBand connector. The default setting
is 1-2 to enable the connection. See the
table on the right for jumper settings.

Infi niBand Enable (JIB1)

Jumper Settings

Jumper Setting Defi nition
1-2 Enabled (Default)
2-3 Disabled

5-26

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

GLAN Enable/Disable

JPL1 enables or disables the GLAN 1/2
ports on the serverboard. See the table
on the right for jumper settings. The
default setting is Enabled.

GLAN Enable

Jumper Settings

Jumper Setting Defi nition
1-2 Enabled (default)
2-3 Disabled

Watch Dog Enable/Disable

Watch Dog (JWD1) is a system monitor
that can reboot the system when a
software application hangs. Close Pins
1-2 to reset the system if an application
hangs. Close Pins 2-3 to generate
non-maskable interrupt signals for the
application that hangs. See the table on
the right for jumper settings. Watch Dog
must also be enabled in the BIOS.

Watch Dog (JWD1)

Jumper Settings

Jumper Setting Defi nition
Pins 1-2 Reset (default)
Pins 2-3 NMI
Open Disabled

VGA Enable

Jumper JPG1 allows the user to enable
the onboard VGA connectors. The
default setting is 1-2 to enable the
connection. See the table on the right
for jumper settings.

VGA Enable (JPG1)

Jumper Settings

Jumper Setting Defi nition
1-2 Enabled (Default)
2-3 Disabled

BMC Enable

Jumper JPB1 allows you to enable the
onboard BMC (Baseboard Management)
Controller to provide IPMI 2.O/KVM
support on the serverboard. See the
table on the right for jumper settings.

BMC Enable (JPB1)

Jumper Settings

Jumper Setting Defi nition
Pins 1-2 BMC Enable (Default)
Pins 2-3 Normal

I2C Bus to PCI-Exp. Slots

Jumpers JI2C1 and JI2C2 allow you to
connect the System Management Bus
(I2C) to PCI-Express slots. The default
setting is Open to disable the connection.
See the table on the right for jumper
settings.

I2C to PCI-E (JI2C1/JI2C2)

Jumper Settings

Jumper Setting Defi nition
1-2 Enabled
2-3 Disabled (Default)

Chapter 5: Advanced Serverboard Setup

5-27

5-10 Onboard Indicators

IPMI Dedicated LAN LEDs

In addition to the Gigabit Ethernet
ports, an IPMI Dedicated LAN is also
located above the Backplane USB ports
0/1 on the serverboard. The amber
LED on the right of the IPMI LAN port
indicates activity, while the green LED
on the left indicates the speed of the
connection. See the table at right for
more information.

Link LED Activity LED

IPMI LAN

GLAN LEDs

The Gigabit LAN ports are located on
the IO Backplane on the serverboard.
On each Gb LAN port, one LED blinks
to indicate activity while the other may be
green, amber or off to indicate the speed
of the connection. See the table on the
right for the functions associated with the
connection speed LED.

Onboard Power LED

An Onboard Power LED is located at
LE1 on the serverboard. When this
LED is on, the system is on. Be sure
to turn off the system and unplug the
power cord before removing or installing
components. See the tables at right for
more information.

Onboard PWR LED Indicator (LE1)

LED Settings

LED Color Status
Off System Off (PWR cable not

connected)
Green System On
Green: Flashing

Quickly

ACPI S1 State

Green: Flashing
Slowly

ACPI S3 (STR) State

LAN LED

(Connection Speed Indicator)

LED Color Defi nition
Off 10 MHz
Green 100 MHz
Amber 1 GHz

IPMI LAN Link LED

(Left) & Activity LED (Right)

Color Status Defi nition
Green:

Solid

Link
(Left)

100 Mb/s

Amber
Blinking

Activity
(Right)

Active

Rear UID LED

The rear U ID LED is loc ated at LE2 o n
the rear of the serverboard. This LED
is used in conjunction with the rear UID
switch to provide ea sy identifi cation o f a
system that might be in need o f service.

UID LED (LE2)

Status

Color/State OS Status
Blue: On Windows OS Unit Identifi ed
Blue: Blinking Linux OS Unit Identifi ed

5-28

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Infi niBand Link LED (LEB1) Settings

Color Status Defi nition
Green Solid Infi niBand Connected
Off Off No connection

Infi niBand Activity LED (LEB2) Settings

Color Status Defi nition
Yellow Solid Infi niBand: Active
Yellow Dim Infi niBand: Connected,

Activity: Idle

Off Off No connection

Infi niBand LED Indicators

Both the X9DRT-IBQF and X9DRT-IBFF
serverboards have two Infi niBand LED
Indicators (LEB1/LEB2) that are located
on the serverboard. The green LED
(LEB1) is the Infi niBand Link LED. The
yellow LED (LEB2) indicates activity.
Refer to the table on the right for details.

BMC Heartbeat LED (LEM1)

Status

Color/State Defi nition
Green: Blinking BMC:Normal

BMC Heartbeat LED

A BMC Heartbeat LED is located at
LEM1 on the serverboard. When LEM1
is blinking, BMC functions normally. See
the tab le at right f or more i nform ation.

5-11 PCI-Express and Serial ATA Connections

PCI-Express 3.0 x16 Slot

A PCI-Express 3.0 x16 slot (Slot 1) is located on the serverboard.

Serial ATA (SATA) Connections

A Front Panel Add-On Card header is
located at JF2 on the serverboard. This
header provides onboard SATA support.
Plug an add-on card in JF2 to use SATA
connections. In addition, two SATA
connections (I-SATA 0/1), located next
to the Intel PCH chip also provide SATA
connections.

SATA Port

Pin Defi nitions

(I-SATA0~I-SATA5)

Pin # Defi nition
1 Ground
2 TXP
3 TXN
4 Ground
5 RXN
6 RXP
7 Ground

Chapter 5: Advanced Serverboard Setup

5-29

Figure 5-6. Driver/Tool Installation Display Screen

5-12 Installing Drivers

The CD that came bundled with the system contains drivers, some of which must
be installed, such as the chipset driver. After inserting this CD into your CD-ROM
drive, the display shown in Figure 5-6 should appear. (If this display does not appear ,
click on the My Computer icon and then on the icon representing your CD-ROM
drive. Finally, double click on the S "Setup" icon.)

Click the icons showing a hand writing on paper to view the readme fi les for each
item. Click the computer icons to the right of these items to install each item (from
top to the bottom) one at a time. After installing each item, you should reboot the
system before moving on to the next item on the list. The bottom icon with a CD
on it allows you to view the entire contents of the CD.

5-30

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Supero Doctor III

The SuperDoctor® III program is a Web base management tool that supports remote
management capability. It includes Remote and Local Management tools. The local
management is called SD III Client. The SuperDoctor III program included on the
CD-ROM that came with your serverboard allows you to monitor the environment
and operations of your system. SuperDoctor III displays crucial system information
such as CPU temperature, system voltages and fan status. See the Figure below
for a display of the SuperDoctor III interface.

Note: The default User Name and Password for SuperDoctor III is ADMIN / ADMIN.
Note: When SuperDoctor is fi rst installed, it adopts the temperature threshold

settings that have been set in BIOS. Any subsequent changes to these thresholds
must be made within SuperDoctor, as the SuperDoctor settings override the BIOS
settings. To set the BIOS temperature threshold settings again, you would fi rst need
to uninstall SuperDoctor.

Figure 5-7. Supero Doctor III Interface Display Screen (Health Information)

Chapter 5: Advanced Serverboard Setup

5-31

Note: The SuperDoctor III program and User’s Manual can be downloaded from the
Supermicro web site at http://www.supermicro.com/products/accessories/software/

SuperDoctorIII.cfm.For Linux, we recommend that you use the SuperoDoctor II

application instead.

Figure 5-8. Supero Doctor III Interface Display Screen (Remote Control)

5-32

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

5-13 Onboard Battery

Caution: There is a danger of explosion if the onboard battery is installed upside

down, which will reverse its polarites (see Figure 5-9). This battery must be replaced
only with the same or an equivalent type recommended by the manufacturer
(CR2032). Dispose of used batteries according to the manufacturer's instructions.

Figure 5-9. Installing the Onboard Battery

LITHIUM BATTERY

BATTERY HOLDER

Please handle used batteries carefully. Do not damage the battery in any way; a
damaged battery may release hazardous materials into the environment. Do not
discard a used battery in the garbage or a public landfi ll. Please comply with the
regulations set up by your local hazardous waste management agency to dispose
of your used battery properly.

Chapter 6: Advanced Chassis Setup

6-1

Chapter 6

Advanced Chassis Setup

This chapter covers the steps required to install components and perform
maintenance on the SC808BT-1K28BP chassis. For component installation, follow
the steps in the order given to eliminate the most common problems encountered.
If some steps are unnecessary, skip ahead to the step that follows.

Tools Required: The only tool you will need to install components and perform
maintenance is a Philips screwdriver.

6-1 Static-Sensitive Devices

Electrostatic discharge (ESD) can damage electronic com ponents. To prevent
damage to any printed circuit boards (PCBs), it is important to handle them very
carefully. The following measures are generally suffi cient to protect your equipment
from ESD damage.

Precautions

• Use a grounded wrist strap designed to prevent static discharge.

• T ouch a grounded metal object before removing any board from its antistatic bag.

• Handle a board by its edges only; do not touch its components, peripheral chips,

memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the serverboard, add-on cards and peripherals back into their antistatic

bags when not in use.

• For grounding purposes, make sure your computer chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and
the serverboard.

Unpacking

The serverboard is shipped in antistatic packaging to avoid static damage. When
unpacking the board, make sure the person handling it is static protected.

6-2

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

SATA Drives (4)

Control Panel

Control Panel

Figure 6-1. Front and Rear Chassis Views

6-2 Control Panel

The control panel is located on the front of the chassis. The LEDs inform you of
system status.

See Chapter 3 for details on the LEDs and the control panel buttons.

Ethernet Ports

USB Ports COM1 Port

IPMI LAN Port VGA Port

Infi niband Port

UID

Chapter 6: Advanced Chassis Setup

6-3

6-3 Chassis Cover

Before operating the SC808 chassis for the fi rst time, it is important to remove the
protective fi lm covering the top of the chassis, in order to allow for proper ventilation
and cooling.

Opening the Chassis Cover (Figure 6-2))

1. Disconnect the chassis from any power source and remove all four screws.

2. Gently push down on the chassis cover in the areas indicated in the
illustration.

3. Push the cover toward the rear of the chassis

4. Lift the cover upwards and off the chassis.

Caution: Except for short periods of time, do NOT operate the server without
the cover in place. The chassis cover must be in place to allow proper airfl ow
and prevent overheating.

Figure 6-2. Opening the Chassis Cover

Remove this

screw

Remove this

screw

Remove this

screw

1

3

1

2

1

2

1

3

6-4

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

6-4 Air Shrouds

Air shrouds concentrate airfl ow to maximize fan effi ciency. The SC808 chassis air
shroud does not require screws to set up. The SC808 chassis requires two identical
air shrouds.

Installing an Air Shroud

1. Confi rm that all six fans are in place and working properly

2. Place the fi rst air shroud into the chassis. The air shroud sits behind the
system fans. Each air shroud covers three fans.

3. Install the second air shroud in the same manner as the fi rst.

6-5 Checking the Airfl ow

Checking Airfl ow

1. Make sure there are no objects obstructing airfl ow in and out of the server. In
addition, if you are using a front bezel, make sure the bezel's fi lter is replaced
periodically.

2. Do not operate the server without drives or drive carriers in the drive bays.
Use only recommended server parts.

3. Make sure no wires or foreign objects obstruct air fl ow through the chassis.
Pull all excess cabling out of the airfl ow path or use shorter cables.

4. The control panel LEDs inform you of system status. See “Chapter 3: System
Interface” for details on the LEDs and the control panel buttons.

Chapter 6: Advanced Chassis Setup

6-5

6-6 System Fans

Six fans provide cooling for the chassis (Figure 6-3). These fans circulate air through
the chassis as a means of lowering the chassis internal temperature. The SC808
system fans are hot-swappable. There is no need to power-down the system when
switching fans.

Figure 6-3: System Fan

Rubber Feet

Figure 6-4: System Fan Placement

Changing a System Fan (Figure 6-4)

1. If necessary, open the chassis while the power is running to determine which
fan has failed. (Never run the server for an extended period of time with the
chassis open.)

2. Remove the failed fan's power cord from the serverboard.

3. Lift the fan from the chassis.

4. Place the new fan into the vacant space in the housing while making sure
the arrows on the top of the fan (indicating air direction) point in the same
direction as the arrows on the other fans. Make sure all four of the fan's
rubber feet are in place.

5. Confi rm that the fan is working properly before replacing the chassis cover.

6-6

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

6-7 Installing and Removing Hard Drives

Accessing the Drive Bays

SATA Drives: You do not need to access the inside of the chassis or remove power
to replace or swap SATA drives. Each hard disk drive is in a separate carrier that
may be removed to access its hard drive. Proceed to the next step for instructions.
You must use standard 1" high, SATA drives in the system.

Caution: Except for short periods of time (swapping hard drives), do not operate
the server with the carriers abscent.

Removing Hard Drive Carriers from the Chassis (Figure 6-5)

1. Press the release button on the drive carrier. This extends the drive handle.

2. Use the handle to pull the drive out of the chassis.

Figure 6-5: Removing Hard Drive

1

1

1

2

Chapter 6: Advanced Chassis Setup

6-7

The drives are mounted in drive carriers to simplify their installation and removal
from the chassis. These carriers also help promote proper airfl ow in the drive bays
(Figure 6-6).

Figure 6-6: Chassis Drive Carrier

Drive Tray

Dummy Drive

Installing a Drive into the Hard Drive Carrier

1. Remove the two screws securing the dummy drive to the drive carrier (Figure
6-7).

Figure 6-7: Removing Dummy Drive from Carrier

1

1

1

1

2. Lift the dummy drive up and out of the carrier.

3. Install a new drive into the carrier with the printed circuit board side facing
downward so that the mounting holes align with those in the carrier.

4. Secure the hard drive by tightening all six screws (Figure 6-8).

6-8

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Figure 6-8: Removing Hard Drive

Drive Tray

SATA Hard Drive

1

4

1

4

5. Use the open handle to slide the drive carrier into the chassis.

6. Close the drive carrier handle.

Caution! Enterprise level hard disk drives are recommended for use in
Supermicro chassis and servers. For information on recommended HDDs,
visit the Supermicro Web site at http://www.supermicro.com/products/nfo/files/

storage/SAS-1-CompList-110909.pdf

Chapter 6: Advanced Chassis Setup

6-9

6-8 Installing the Serverboard

I/O Shield

The I/O shield holds the serverboard ports in place. The I/O shield does not require
installation, however, the serverboard must match up with the I/O shield (Figure 6-9).

Figure 6-9: I/O Shield Placement

I/O Shields

Permanent and Optional Standoffs

Standoffs prevent short circuits by securing space between the serverboard and
the chassis surface. The SC808 chassis includes permanent standoffs in locations
used by the serverboards. These standoffs accept the rounded Phillips head screws
included in the SC808 accessories packaging.

Some serverboards require additional screws for heatsinks, general components
and for stability. Optional standoffs are used for these serverboards.

To use an optional standoff, you must place a hexagonal screw through the bottom
the chassis and secure the screw with the hexagonal nut (rounded side up).

Depending upon the confi guration of the serverboard being used, it is also possible
that some of the optional standoffs which are pre-installed in the chassis, may need
to be removed.

Installing the Serverboard (Figure 6-10)

1. Review the documentation that came with your serverboard. Become
familiar with component placement, requirements, precautions, and cable
connections.

2. Disconnect the chassis from any power source and open the chassis cover.

3. Remove the expansion card brackets. To do this:
A. Remove screw securing the expansion card bracket to the chassis.
B. Lift the bracket out of the chassis.
C. Repeat this process for the second riser card.

4. Lay the fi rst serverboard in the chassis aligning the standoffs

6-10

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

5. Secure the serverboard to the chassis using the rounded, Phillips head
screws. Each serverboard requires fi ve screws. Do not exceed eight pounds
of torque when tightening down the serverboard.

6. Repeat steps 3 - 5 for the second side of the chassis.

7. Secure the CPU(s), heatsinks, and other components to the serverboard as
described in the serverboard documentation.

8. Connect the cables between the serverboard, backplane, chassis, front panel,
and power supply, as needed. Also, fans may be temporarily removed to
allow access to the backplane ports.

9. Replace the expansion card bracket and secure the bracket with a screw.

Remove these screws

Figure 6-10: Expansion Card Bracket

Chapter 6: Advanced Chassis Setup

6-11

6-9 Expansion Slot Setup

SC808 chassis includes I/O slots for expansion cards. Each side supports one
low profi le, half-length expansion card for a total of two per system (Figure 6-11).

Expansion Card

Slot Clip

Temporary "L" Bracket

Figure 6-11: Expansion Card Placement

Installing Expansion Cards (Figure 6-12)

1. Disconnect the chassis from any power source, lay the chassis on a fl at
surface, and open the chassis cover.

2. Pull open the expansion card slot clip in the rear of the chassis.

3. Slide the temporary expansion card "L" bracket toward the slot clip and
remove the temporary bracket from the chassis.

4. Connect the expansion card to the riser card and slide the expansion card "L"
bracket in to the rear expansion card slot.

5. Close the expansion card slot clip.

6. Close the chassis cover and reconnect the chassis to the power source.

Note: Under normal circumstances, the riser card and expansion card bracket are
not separated.

6-12

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Expansion Card

Bracket

Riser Card

PCI Slot
Cover

Expansion
Card

Figure 6-12: Installing Expansion Cards

Expansion
Card Bracket

Screw

Chapter 6: Advanced Chassis Setup

6-13

6-10 Power Supply

Depending on your chassis model, the SC808 Chassis has a 780, 980 or 1200
Watt power supply. This power supply is auto-switching capable. This enables it to
automatically sense and operate at a 100v to 240v input voltage. An amber light
will be illuminated on the power supply when the power is off. An illuminated green
light indicates that the power supply is operating.

Power Supply Replacement

The SC808 chassis utilizes one power supply. In the unlikely event that the power
supply unit must be replaced, the system will shut down. Replacement units can be
ordered directly from Supermicro (see contact information in the Preface).

Changing the Power Supply (Figure 6-13)

1. Power down the chassis and unplug the AC power cord.

2. Push the release tab (on the back of the power supply) as illustrated.

3. Pull the power supply out using the handle provided.

4. Push the new power supply module into the power bay until you hear a click.

5. Plug the AC power cord back into the module and power up the server.

6-14

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Release Tab

Figure 6-13: Changing the Power Supply

Chapter 7: BIOS

7-1

Chapter 7

BIOS

7-1 Introduction

This chapter describes the AMI BIOS Setup Utility for the X9DRT-IBQF/IBFF/F
serverboard. The 128 MB AMI BIOS® is stored in a Flash EEPROM and can be
easily updated. This chapter describes the basic navigation of the AMI BIOS Setup
Utility setup screens.

Starting BIOS Setup Utility

To enter the AMI BIOS Setup Utility screens, press the <Delete> key while the
system is booting up.

Note: In most cases, the <Delete> key is used to invoke the AMI BIOS setup screen.
There are a few cases when other keys are used, such as <F1>, <F2>, etc.

Each main BIOS menu option is described in this manual. The Main BIOS setup
menu screen has two main frames. The left frame displays all the options that can
be confi gured. Grayed-out options cannot be confi gured. Options in blue can be
confi gured by the user. The right frame displays the key legend. Above the key
legend is an area reserved for a text message. When an option is selected in the
left frame, it is highlighted in white. Often a text message will accompany it. (Note:
the AMI BIOS has default text messages built in. Supermicro retains the option to
include, omit, or change any of these text messages.)

The AMI BIOS Setup Utility uses a key-based navigation system called "hot keys".
Most of the AMI BIOS setup utility "hot keys" can be used at any time during the
setup navigation process. These keys include <F1>, <F10>, <Enter>, <ESC>,
arrow keys, etc.

Note: Options printed in Bold are default settings.

How To Change the Confi guration Data

The confi guration data that determines the system parameters may be changed by
entering the AMI BIOS Setup utility. This Setup utility can be accessed by pressing
<Del> at the appropriate time during system boot.

7-2

SUPERSERVER 6017TR-TQF/TFF/TF User's Manual

Starting the Setup Utility

Normally, the only visible Power-On Self-Test (POST) routine is the memory test.
As the memory is being tested, press the <Delete> key to enter the main menu of
the AMI BIOS Setup Utility. From the main menu, you can access the other setup
screens. An AMI BIOS identifi cation string is displayed at the left bottom corner of
the screen below the copyright message.

Caution! Do not upgrade the BIOS unless your system has a BIOS-related issue.
Flashing the wrong BIOS can cause irreparable damage to the system. In no event shall
Supermicro be liable for direct, indirect, special, incidental, or consequential damages
arising from a BIOS update. If you have to update the BIOS, do not shut down or reset
the system while the BIOS is updating. This is to avoid possible boot failure.

7-2 Main Setup

When you fi rst enter the AMI BIOS Setup utility , you will enter the Main setup screen.
You can always return to the Main setup screen by selecting the Main tab on the
top of the screen. The Main BIOS Setup screen is shown below.