Supero SUPERSERVER 6017R-WRF, SUPERSERVER 6017R-NTF User Manual

SUPER

®

USER'S MANUAL

Revision 1.0a

SUPERSERVER

6017R-WRF

6017R-NTF

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at

www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTW ARE, OR DA TA ST ORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See

www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.

Manual Revision 1.0b
Release Date: June 06, 2014

Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.

Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2014 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the SuperServer 6017R-WRF/NTF .
Installation and maintenance should be performed by experienced technicians only .

The SuperServer 6017R-WRF/NTF is a 1U rackmount server based on the
SC815TQ-R700WB/600WB server chassis and the X9DRW-iF serverboard. Please
refer to our web site for updates on supported processors.

The only difference between the 6017R-WRF and 6017R-NTF servers is that the
6017R-WRF uses the R700WB 700 Watt power suppply, and the 6017R-NTF uses
the 600WB 600 Watt power supply.

Manual Organization

Chapter 1: Introduction

The fi rst chapter provides a checklist of the main components included with the
server system and describes the main features of the X9DRW-iF serverboard and
the SC815TQ-R700WB/600WB chassis.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer
6017R-WRF/NTF into a rack and check out the server confi guration prior to
powering up the system. If your server was ordered without the processor and
memory components, this chapter will refer you to the appropriate sections of the
manual for their installation.

Chapter 3: System Interface

Refer to this chapter for details on the system interface, which includes the functions
and information provided by the control panel on the chassis as well as other LEDs
located throughout the system.

Chapter 4: Standardized Warning Statements for AC Systems

You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 6017R-WRF/NTF.

iii

Preface

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

iv

Chapter 5: Advanced Serverboard Setup

This chapter provides detailed information on the X9DRW-iF serverboard,
including the locations and functions of connectors, headers and jumpers. Refer
to this chapter when adding or removing processors or main memory and when
reconfi guring the serverboard.

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the SC815TQ-R700WB/600WB
chassis. You should follow the procedures given in this chapter when installing,
removing or reconfi guring Serial A T A or peripheral drives and when replacing system
power supply units and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed information
on running the CMOS Setup Utility.

Appendix A: BIOS POST Error Codes
Appendix B: Installing Windows
Appendix C: System Specifi cations

v

Preface

Notes

vi

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Table of Contents

Chapter 1 Introduction

1-1 Overview .........................................................................................................1-1

1-2 Serverboard Features .....................................................................................1-2

Processors ......................................................................................................1-2

Memory ...........................................................................................................1-2

Serial ATA ....................................................................................................... 1-2

Onboard Controllers/Ports .............................................................................. 1-3

Graphics Controller .........................................................................................1-3

Other Features ................................................................................................ 1-3

1-3 Server Chassis Features ................................................................................ 1-3

System Power ................................................................................................. 1-3

Hard Drive Subsystem .................................................................................... 1-3

PCI Expansion Slots .......................................................................................1-4

Front Control Panel ......................................................................................... 1-4

I/O Backplane ..................................................................................................1-4

Cooling System ............................................................................................... 1-4

1-4 Advanced Power Management ....................................................................... 1-5

Intel® Intelligent Power Node Manager (NM) .................................................1-5

Manageability Engine (ME) ............................................................................. 1-5

1-5 Contacting Supermicro ....................................................................................1-7

Chapter 2 Server Installation

2-1 Overview .........................................................................................................2-1

2-2 Unpacking the System .................................................................................... 2-1

2-3 Preparing for Setup ......................................................................................... 2-1

Choosing a Setup Location .............................................................................2-2

2-4 Warnings and Precautions .............................................................................. 2-2

Rack Precautions ............................................................................................ 2-2

Server Precautions ..........................................................................................2-2

Rack Mounting Considerations ....................................................................... 2-3

Ambient Operating Temperature ................................................................ 2-3

Reduced Airfl ow ......................................................................................... 2-3

Mechanical Loading ................................................................................... 2-3

Circuit Overloading ..................................................................................... 2-4

Reliable Ground ......................................................................................... 2-4

2-5 Installing the System into a Rack ...................................................................2-5

Identifying the Sections of the Rack Rails ...................................................... 2-5

vii

Table of Contents

Installing the Inner Rails ................................................................................. 2-5

Installing the Outer Rails .................................................................................2-6

Installing the Server into the Rack ..................................................................2-7

2-6 Checking the Serverboard Setup ....................................................................2-8

2-7 Checking the Drive Bay Setup ........................................................................2-9

Chapter 3 System Interface

3-1 Overview .........................................................................................................3-1

3-2 Control Panel Buttons ..................................................................................... 3-2

Reset ...............................................................................................................3-2

Power ..............................................................................................................3-2

UID ..................................................................................................................3-2

3-3 Control Panel LEDs ........................................................................................ 3-3

Information LED ..............................................................................................3-3

NIC2 ................................................................................................................3-3

NIC1 ................................................................................................................3-3

HDD ................................................................................................................. 3-3

Power ..............................................................................................................3-4

3-4 Hard Drive Carrier LEDs ................................................................................. 3-4

Chapter 4 Standardized Warning Statements for AC Systems

4-1 About Standardized Warning Statements ....................................................... 4-1

Warning Defi nition ...........................................................................................4-1

Installation Instructions ....................................................................................4-4

Circuit Breaker ................................................................................................ 4-5

Power Disconnection Warning ........................................................................ 4-6

Equipment Installation ..................................................................................... 4-8

Restricted Area ................................................................................................ 4-9

Battery Handling ............................................................................................4-10

Redundant Power Supplies .......................................................................... 4-12

Backplane Voltage ........................................................................................4-13

Comply with Local and National Electrical Codes ........................................ 4-14

Product Disposal ........................................................................................... 4-15

Easy Swap Fan Warning ..............................................................................4-16

Power Cable and AC Adapter ......................................................................4-18

viii

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Chapter 5 Advanced Serverboard Setup

5-1 Handling the Serverboard ............................................................................... 5-1

Precautions .....................................................................................................5-1

Unpacking .......................................................................................................5-1

5-2 Processor and Heatsink Installation................................................................5-2

Installing a Passive CPU Heatsink .................................................................5-6

Removing the Heatsink ................................................................................... 5-7

5-3 Connecting Cables .......................................................................................... 5-7

Connecting Data Cables ................................................................................. 5-7

Connecting Power Cables .............................................................................. 5-8

Connecting the Control Panel ......................................................................... 5-8

5-4 I/O Ports ..........................................................................................................5-9

5-5 Installing Memory .......................................................................................... 5-10

Memory Support ............................................................................................5-10

5-6 Adding PCI Expansion Cards .......................................................................5-12

PCI Expansion Slots ................................................................................ 5-12

5-7 Serverboard Details ...................................................................................... 5-13

X9DRW-iF Quick Reference ......................................................................... 5-14

5-8 Connector Defi nitions ................................................................................... 5-16

Power Connectors ...................................................................................5-16

PW_ON Connector ...................................................................................5-17

Reset Connector ...................................................................................... 5-17

Power Fail LED ........................................................................................5-17

Overheat/Fan Fail LED (OH)....................................................................5-17

NIC1 (LAN1) LED .....................................................................................5-18

HDD LED ..................................................................................................5-18

Power On LED .........................................................................................5-18

NMI Button ............................................................................................... 5-18

Chassis Intrusion ...................................................................................... 5-18

Universal Serial Bus (USB) ...................................................................... 5-19

Ethernet Ports .......................................................................................... 5-19

Video Connection ..................................................................................... 5-19

Serial Ports ............................................................................................... 5-20

Fan Headers .............................................................................................5-20

Power LED/Speaker ................................................................................. 5-20

Unit Identifi er Switch ................................................................................5-21

Internal Speaker ....................................................................................... 5-21

Overheat LED/Fan Fail ............................................................................ 5-22

Table of Contents

ix

Power SMB (I2C) Connector ....................................................................5-22

Port 80 Header ......................................................................................... 5-22

IPMB .........................................................................................................5-23

T-SGPIO 1/2 Headers .............................................................................. 5-23

DOM Power Connector ............................................................................ 5-23

Standby Power Connector .......................................................................5-23

Legacy Wake-On-LAN Header (JSTBY) .................................................. 5-24

5-9 Jumper Settings ............................................................................................5-25

Explanation of Jumpers ................................................................................ 5-25

CMOS Clear ............................................................................................. 5-25

LAN Enable/Disable .................................................................................5-26

Watch Dog Enable/Disable ......................................................................5-26

VGA Enable/Disable .................................................................................5-26

BMC Enable ............................................................................................ 5-26

I2C Bus to PCI-Exp. Slots ........................................................................5-26

5-10 Onboard Indicators ........................................................................................5-27

GLAN LEDs .............................................................................................. 5-27

IPMI Dedicated LAN LEDs .......................................................................5-27

Onboard Power LED ................................................................................ 5-27

Rear UID LED ......................................................................................... 5-28

BMC Heartbeat LED ................................................................................ 5-28

5-11 SATA Drive Connections ............................................................................... 5-28

SATA/SC8U Ports .....................................................................................5-28

5-12 Installing Software ......................................................................................... 5-29

SuperDoctor III .............................................................................................. 5-30

5-13 Serverboard Battery ......................................................................................5-32

Chapter 6 Advanced Chassis Setup

6-1 Static-Sensitive Devices ..................................................................................6-1

Precautions .....................................................................................................6-1

6-2 Control Panel ..................................................................................................6-2

6-3 System Fans ...................................................................................................6-2

System Fan Failure ......................................................................................... 6-3

6-4 Drive Bay Installation/Removal ....................................................................... 6-4

Removing the Front Bezel ..............................................................................6-4

Accessing the Drive Bays ............................................................................... 6-4

Hard Drive Installation ..................................................................................... 6-5

DVD-ROM Drive Installation ...........................................................................6-6

x

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

6-5 Power Supply .................................................................................................. 6-7

Redundant Power Supply Failure ..............................................................6-7

Chapter 7 BIOS

7-1 Introduction ......................................................................................................7-1

Starting the Setup Utility .................................................................................7-1

7-2 Main Menu ...................................................................................................... 7-1

System Time/System Date .............................................................................7-2

7-3 Advanced Settings Menu ................................................................................ 7-2

7-4 Event Logs .................................................................................................... 7-22

7-5 IPMI ...............................................................................................................7-24

7-6 Boot ...............................................................................................................7-26

7-7 Security .........................................................................................................7-27

7-8 Save & Exit ................................................................................................... 7-27

Appendix A BIOS Error Beep Codes
Appendix B System Specifi cations

Chapter 1

Introduction

1-1 Overview

The SuperServer 6017R-WRF/NTF is a high-end server comprised of two main
subsystems: the SC815TQ-R700WB/600WB 1U server chassis and the X9DRW-iF
dual processor serverboard. Please refer to our web site for information on operating
systems that have been certifi ed for use with the system (www.supermicro.com).

In addition to the serverboard and chassis, various hardware components have been
included with the SuperServer 6017R-WRF/NTF, as listed below:

• Heatsinks:

One (1) 1U Passive CPU Heatsinks (SNK-P0047PSC)
One (1) 1U Passive CPU Heatsinks (SNK-P0047PS)

• One (1) SC815/113/116 Intel DP X9, X8 PC air shroud (MCP-310-19002-0N)

(6017R-WRF only)

• One (1) SC815/113/116 Intel DP X9, X8 PC air shroud (MCP-310-19001-0N)

(6017R-NTF only)

• Fans:

Four (4) 40x56mm 4-pin PWM chassis middle fans (FAN-0086L4)
One (1) 40x56mm 4-pin PWM chassis middle fan (MCP-340-00022-0N)

• One (1) 70-cm round 20-to-20-pin Front Panel Control Cable (CBL-0335L)

• SAS/SATA Accessories

One (1) SAS/SATA backplane (BPN-SAS-815TQ-O-P)
One (1) 30AWG 76/66/54/45-cm, w/66-cm AOC connection cable
(CBL-0343L-01) (6017R-WRF only)
One (1) 30AWG 64/54/44/34-cm, w/64-cm SATA connection cable
(CBL-0188L-02) (6017R-NTF only)
Four (4) hot-swap 3.5" hard-disk drive trays (MCP-220-00075-0B)

• One (1) Riser Card (RSC-R1UW-2E16-O-P)

• Rail Kit sets:

One (1) set outer rail (screw) for 1U chassis (MCP-290-00101-0N)
One (1) set Inner rail, front (screw) for 1U chassis (MCP-290-00105-0N)
One (1) set Inner rail, extension (screw) for 1U chassis (MCP-290-00109-0N)

Chapter 1: Introduction

1-1

1-2

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Note: For your system to work properly, please follow the links below to download
all necessary drivers/utilities and the user’s manual for your server.

• Supermicro product manuals: http://www.supermicro.com/support/manuals/

• Product drivers and utilities: ftp://ftp.supermicro.com

• Product safety information:

http://super-dev/about/policies/safety_information.cfm

• If you have any questions, please contact our support team at:

[e-mail]

1-2 Serverboard Features

At the heart of the SuperServer 6017R-WRF/NTF lies the X9DRW-iF, a dual
processor serverboard based on the Intel PCH 602 chipset. Below are the main
features of the X9DRW-iF. (See Figure 1-1 for a block diagram of the chipset).

Processors

The X9DRW-iF supports single or dual E5-2600 Series processors in
Socket R LGA2011 type sockets. Please refer to our web site for a complete listing
of supported processors (www.supermicro.com).

Memory

The X9DRW-iF has sixteen (16) quad channel 240-pin DIMM sockets that can
support up to 512 GB of DDR3 1600/1333/1066/800 MHz speed registered
ECC RDIMM/LRDIMM SDRAM in two-channel memory bus. Memory sizes of
1GB, 2GB, 4GB, 8GB, 16GB and 32GB @ 1.35V/1.5V voltages are supported.
Please refer to Chapter 5 for installing memory.

Note: LRDIMM (Reduced Load) memory supports only 1333/1066/800 MHz speed
memory.

Serial ATA

An on-chip (Intel PCH 602) SATA controller is integrated into the X9D RW-iF to
provid e a s i x-port SATA subsys te m (two SATA 3.0 and four SATA 2.0 ports), which
is R AID 0, 1, 5 and 10 (W ind ows SATA) or R A ID 0, 1 an d 10 (LINUX ) supp or ted.
The SATA dri ves are ho t-swap pable u nits.

Note: You must have RAID set up to enable the hot-swap capability of the SATA
drives. D ocum entati on on R AI D setup gui deline s can be fo und on our we b site.

Chapter 1: Introduction

1-3

Onboard Controllers/Ports

The color-coded I/O ports on the X9DRW-iF include two COM ports (one header
and one port), a VGA (monitor) port, eight USB 2.0 ports (4x rear, 4x header), two
gigabit Ethernet ports and one dedicated IPMI LAN port.

Note 1: For more information on IPMI confi guration, please refer to the IPMI User's
Guide posted on our website at

http://www.supermicro.com/support/manuals/ for

more details.

Graphics Controller

The X9DRW-iF features an integrated Renesas Base-board Controller (BMC) chip,
which also acts as a video controller.

Other Features

Other onboard features that promote system health include onboard voltage
monitors, auto-switching voltage regulators, chassis and CPU overheat sensors,
power management, AC power loss recovery, virus protection and BIOS rescue.

1-3 Server Chassis Features

The SuperServer 6017R-WRF/NTF is built upon the SC815TQ-R700WB/600WB
chassis. Details on the chassis and on servicing procedures can be found in Chapter

6.The following is a general outline of the main features of both chassis.

System Power

The SC815TQ-R700WB/600WB features either a redundant 700 Watt power supply
(6017R-WRF server) or a single 600 Watt power supply (6017R-NTF server). The
system does not need to be shut down when replacing or removing a single power
supply module.

Hard Drive Subsystem

The SC815TQ-R700WB/600WB cha ssis was design ed to suppor t four hot-swap
SAT A hard drives. (The 6017R-WRF requires a PCI-E controller card - not included
with system.)

Note: For the 6 017R-WRF, the ha rd drives a re conne cted to fou r onboard S ATA
conne ctio ns fro m the SCU C ontro ller.

1-4

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

PCI Expansion Slots

A riser card (RSC-R1UW-2E16-O-P) on the left side of the chassis can support two
PCI-E x16 add-on cards. See our webs site for details (http://www.supermicro.com/

products/info/UIO.cfm). See section 5-6 for further details.

Front Control Panel

The chassis' control panel provides you with system monitoring and control. LEDs
indicate system power, HDD activity, network activity (two) and UID/overheat/fan
fail/power fail. A main power button, a system reset button and a UID button are
also included.

I/O Backplane

The SC815TQ-R700WB/600WB is an extended ATX form factor chassis that is
designed to be used in a 1U rackmount confi guration. Ports on the I/O backplane
include one COM port, a VGA port, four USB 2.0 ports, two gigabit LAN Ethernet
ports and one dedicated IPMI LAN port. A UID (Unit Identifi er) button and LED are
also located beside the VGA port.

Cooling System

The SC815TQ-R700WB/600WB chassis has an innovative cooling design that
features fi ve sets of 4-cm counter-rotating fans located in the middle section of the
chassis. There is a "Fan Speed Control Mode" setting in IPMI that allows chassis
fan speed to be determined by system temperature. The power supply module also
includes a cooling fan.

Chapter 1: Introduction

1-5

1-4 Advanced Power Management

Intel® Intelligent Power Node Manager (NM)

The Intel® Intelligent Power Node Manager (IPNM) provides your system with
real-time thermal control and power management for maximum energy effi ciency.
Although IPNM Specifi cation Version 1.5 is supported by the BMC (Baseboard
Management Controller), your system must also have IPNM-compatible
Manageability Engine (ME) fi rmware installed to use this feature.

Manageability Engine (ME)

The Manageability Engine, which is an ARC controller embedded in the IOH (I/O
Hub), provides Server Platform Services (SPS) to your system. The services
provided by SPS are different from those proveded by the ME on client platforms.

1-6

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Figure 1-1. Intel PCH 602 Chipset:

System Block Diagram

Note: This is a general block diagram. Please see Chapter 5 for details.

PROCESSOR

PROCESSOR

DDR3 DIMM

#1

#2

DDR3 DIMM

DDR3 DIMM

DDR3 DIMM

DDR3 DIMM

#2

#1

DDR3 DIMM

G

A

CPU Rear

DDR3 DIMM

B

DDR3 DIMM

D

C

H

F

E

Socket 00

Socket 01

#1

#2

#1

#2

#1

#2

#1

#2

#1

#2

#1

#2

P0

P0

P1

P1

x1

x16

x16

x16

J1

Right Slot

PCIE 3.0x16

DMI

PE3 PE2 PE1

QPI

QPI

CPU Front

DMI

PE1PE2PE3

P0PE3

J3

Left Slot

PCIE 3.0x16+x16

x4 (Lane4~7)

UL1

I350AM2

JLAN1

RJ45

JLAN2

RJ45

Lane Reversal & Polarity Inversion

DMI: Lane Reversal

BIOS

SPI Flash

SPI

DMI
PEG [0...3]

PET8 USB [10,11] LPC

SSB

PCH C602

Gen 3 [1...7]

SATA [0...5]

USB [0...9]

SATA Gen3

SATA Gen2

SATA0

SATA1

SATA2

SATA3

SATA4

SATA5

DDR3 RAM

Renesas

VGA

BMC

TPM Chip

Super I/O

W83527

NCT7904D

HW Monitor

VGA

CONN

PHY

RTL8211E
IPMI LAN

RJ45

REAR

HDR 2X5

REAR

3Gbps

6Gbps

JSM2(SCU4~7)

(3F only)

JSM1(SCU0~3)

Chapter 1: Introduction

1-7

1-5 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)
Web Site:

www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)
Web Site:

www.supermicro.nl

Asia-Pacifi c

Address: Super Micro Computer, Inc.

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 235

Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
Email: [e-mail]
Web Site:

www.supermicro.com.tw

1-8

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Notes

Chapter 2: Server Installation

2-1

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your SuperServer
6017R-WRF/NTF up and running. Following these steps in the order given should
enable you to have the system operational within a minimum amount of time.
This quick setup assumes that your system has come to you with the processors
and memory preinstalled. If your system is not already fully integrated with a
serverboard, processors, system memory etc., please turn to the chapter or section
noted in each step for details on installing specifi c components.

2-2 Unpacking the System

You should inspect the box the SuperServer 6017R-WRF/NTF was shipped in and
note if it was damaged in any way. If the server itself shows damage you should
fi le a damage claim with the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the SuperServer
6017R-WRF/NTF. It should be situated in a clean, dust-free area that is well
ventilated. Avoid areas where heat, electrical noise and electromagnetic fi elds are
generated. You will also need it placed near a grounded power outlet. Be sure to
read the Rack and Server Precautions in the next section.

2-3 Preparing for Setup

The box the SuperServer 6017R-WRF/NTF was shipped in should include two
sets of rail assemblies, two rail mounting brackets and the mounting screws you
will need to install the system into the rack. Follow the steps in the order given to
complete the installation process in a minimum amount of time. Please read this
section in its entirety before you begin the installation procedure outlined in the
sections that follow.

2-2

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Choosing a Setup Location

• Leave enough clearance in front of the rack to enable you to open the front door

completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for suffi cient airfl ow and ease in servicing.This product is for
installation only in a Restricted Access Location (dedicated equipment rooms,
service closets and the like).

• This product is not suitable for use with visual display work place devices

acccording to §2 of the the German Ordinance for Work with Visual Display Units.

2-4 Warnings and Precautions

Warning! To prevent bodily injury when mounting or servicing this unit in a

rack, you must take special precautions to ensure that the system remains stable.
The following guidelines are provided to ensure your safety:

• This unit should be mounted at the bottom of the rack if it is the only unit in

the rack.

• When mounting this unit in a partially fi lled rack, load the rack from the bottom

to the top with the heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before

mounting or servicing the unit in the rack.

Rack Precautions

• Ensure that the leveling jacks on the bottom of the rack are fully extended to

the fl oor with the full weight of the rack resting on them.

• In single rack installation, stabilizers should be attached to the rack. In multiple

rack installations, the racks should be coupled together.

• Always make sure the rack is stable before extending a component from the

rack.

• You should extend only one component at a time - extending two or more

simultaneously may cause the rack to become unstable.

Server Precautions

• Review the electrical and general safety precautions in Chapter 4.

• Determine the placement of each component in the rack before you install the

rails.

Chapter 2: Server Installation

2-3

• Install the heaviest server components on the bottom of the rack fi rst, and then

work up.

• Use a regulating uninterruptible power supply (UPS) to protect the server from

power surges, voltage spikes and to keep your system operating in case of a
power failure.

• Allow the hot plug SATA drives and power supply modules to cool before

touching them.

• Always keep the rack's front door and all panels and components on the servers

closed when not servicing to maintain proper cooling.

Rack Mounting Considerations

Warning: Do not pick up the server with the front handles. They are

designed to pull the system from a rack only.

Stability Hazard: The rack stabilizing mechanism must be in place, or the
rack must be bolted to the fl oor before you slide the unit out for servicing. Failure
to stabilize the rack can cause the rack to tip over.

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating
temperature of the rack environment may be greater than the ambient temperature
of the room. Therefore, consideration should be given to installing the equipment
in an environment compatible with the manufacturer’s maximum rated ambient
temperature (Tmra).

Reduced Airfl ow

Equipment should be mounted into a rack so that the amount of airfl ow required
for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.

2-4

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Circuit Overloading

Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack
itself should be grounded. Particular attention should be given to power supply
connections other than the direct connections to the branch circuit (i.e. the use of
power strips, etc.).

Chapter 2: Server Installation

2-5

Figure 2-1. Identifying the Sections of the Rack Rails

(right side rail shown)

2-5 Installing the System into a Rack

This section provides information on installing the SuperServer 6017R-WRF/NTF
into a rack unit with the rack rails provided. If the system has already been mounted
into a rack, you can skip ahead to Sections 2-5 and 2-6.

There are a variety of rack units on the market, which may mean the assembly
procedure will differ slightly. You should also refer to the installation instructions that

came with the rack unit you are using.

Identifying the Sections of the Rack Rails

You should have received two rack rail assemblies in the rack mounting kit. Each
assembly consists of two sections: an inner fi xed chassis rail that secures directly
to the server chassis and an outer fi xed rack rail that secures directly to the rack
itself (see Figure 2-1). Two pairs of short brackets to be used on the front side of
the outer rails are also included.

Installing the Inner Rails

Both the left and right side inner rails have been pre-attached to the chassis.
Proceed to the next step.

2-6

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Figure 2-2. Installing the Rack Rails

Installing the Outer Rails

Begin by measuring the distance from the front rail to the rear rail of the rack.
Attach a short bracket to the front side of the right outer rail and a long bracket to
the rear side of the right outer rail. Adjust both the short and long brackets to the
proper distance so that the rail can fi t snugly into the rack. Secure the short bracket
to the front side of the outer rail with two screws and the long bracket to the rear
side of the outer rail with three screws. Repeat these steps for the left outer rail.
See Figure 2-2 for details

Locking Tabs: Both chassis rails have a locking tab, which serves two functions.
The fi rst is to lock the server into place when installed and pushed fully into the
rack, which is its normal position. Secondly, these tabs also lock the server in place
when fully extended from the rack. This prevents the server from coming completely
out of the rack when you pull it out for servicing.

Chapter 2: Server Installation

2-7

Figure 2-3. Installing the Server into a Rack

Installing the Server into the Rack

You should now have rails attached to both the chassis and the rack unit. The next
step is to install the server into the rack. Do this by lining up the rear of the chassis
rails with the front of the rack rails. Slide the chassis rails into the rack rails, keeping
the pressure even on both sides (you may have to depress the locking tabs when
inserting). See Figure 2-3 for details.

When the server has been pushed completely into the rack, you should hear the
locking tabs "click".

Note: The fi gure above is for illustrative purposes only. Always install servers to
the bottom of the rack fi rst.

2-8

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Figure 2-5. Accessing the Inside of the System

2-6 Checking the Serverboard Setup

After you install the SuperServer 6017R-WRF/NTF in the rack, you will need to
open the top cover to make sure the serverboard is properly installed and all the
connections have been made.

Accessing the Inside of the System (Figure 2-5)

1. First, grasp the two handles on either side and pull the system straight out
until it locks (you will hear a "click").

2. Depress the two buttons on the top of the chassis to release the top cover
(1).

3. Push the cover away from you (toward the rear of the chassis) until it stops
(2). You can then lift the top cover from the chassis to gain full access to the
inside of the server. See Figure 2-5.

4. To remove the system from the rack completely, depress the locking tabs in
the chassis rails (push the right-side tab down and the left-side tab up) to
continue to pull the system out past the locked position.

Chapter 2: Server Installation

2-9

Checking the Components

1. You may have one or two processors already installed in the serverboard.
Each processor needs its own heatsink. See Chapter 5 for instructions on
processor and heatsink installation.

2. Your server system may have come with system memory already installed.
Make sure all DIMMs are fully seated in their slots. For details on adding
system memory, refer to Chapter 5.

3. If desired, you can install add-on cards to the system. See Chapter 5 for
details on installing PCI add-on cards.

4. Make sure all power and data cables are properly connected and not blocking
the chassis airfl ow. See Chapter 5 for details on cable connections.

2-7 Checking the Drive Bay Setup

Next, you should check to make sure the peripheral drives and the SA TA drives and
SA TA backplane have been properly installed and all connections have been made.

Checking the Drives

1. All drives are accessable from the front of the server. The SATA disk drives
can be installed and removed from the front of the chassis without removing
the top chassis cover.

2. A slim DVD-ROM drive should be preinstalled in your server. For servicing
the DVD-ROM drive, you will need to remove the top chassis cover. Refer to
Chapter 6 if you need to reinstall a DVD-ROM drive to the system.

3. Depending upon your system's confi guration, your system may have one or
more drives already installed. If you need to install SATA drives, please refer
to Chapter 6.

Checking the Airfl ow

1. Airfl ow is provided by four sets of 4-cm fans (each set of fans consists of
two fans that are mounted back to back). The system component layout was
carefully designed to direct suffi cient cooling airfl ow to the components that
generate the most heat.

2. Note that all power and data cables have been routed in such a way that they
do not block the airfl ow generated by the fans.

Providing Power

1. The last thing you must do is to provide input power to the system. Plug the
power cords from the power supply modules into a high-quality power strip
that offers protection from electrical noise and power surges.

2. It is recommended that you use an uninterruptible power supply (UPS).

2-10

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Notes

Chapter 3: System Interface

3-1

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the control panel as well as others on the SATA drive
carriers to keep you constantly informed of the overall status of the system as well
as the activity and health of specifi c components. There are also three buttons on
the chassis control panel and an on/off switch on the power supply. This chapter
explains the meanings of all LED indicators and the appropriate response you may
need to take.

Figure 3-1: System Interface

1

8

1

9

7 346 5 12

Server Interface Buttons and LEDs

No. Description

1 Power Button
2 Reset Button
3 Power LED
4 Device Activity LED
5 LAN1 LED and LAN2 LED
6 Information LED
7 Unit Identifi er Button
8 Hard Drive Signal
9 Hard Drive Fail

3-2

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

UID

Depressing the UID (unit identifi er) button illuminates an LED on both the front
and rear of the chassis for easy system location in large stack confi gurations. The
LED will remain on until the button is pushed a second time. Another UID button
on the rear of the chassis serves the same function. See the table in Figure 3-1 for
descriptions of UID LED states.

Universal Information LED States

State Indication

Fast Blinking Red (1x/sec) Fan Fail
Solid Red CPU Overheat
Slow Blinking Red (1x/4 sec) Power Fail
Solid Blue Local UID Button Depressed
Blinking Blue IPMI-Activated UID

Note: deactivating the UID LED must be performed in the same way it was activated.
(If the UID LED was activated via IPMI, you can only turn the LED off via IPMI and
not with the UID button.)

Power

This is the main power button, which is used to apply or turn off the main system
power. T urning off system power with this button removes the main power but keeps
standby power supplied to the system.

Reset

Use the reset button to reboot the system.

3-2 Control Panel Buttons

There are three push-buttons located on the front of the chassis: a reset button, a
UID button and a power on/off button.

Chapter 3: System Interface

3-3

3-3 Control Panel LEDs

The control panel located on the front of the SC815TQ-R700WB/600WB chassis
has fi ve LEDs. These LEDs provide you with critical information related to different
parts of the system. This section explains what each LED indicates when illuminated
and any corrective action you may need to take.

NIC2

Indicates network activity on LAN2 when fl ashing.

Information LED

See the following table for the status shown by this LED.

Information LED

Status Description

Continously on and red An overheat ocondition has occured. (This may be caused by cable congestion.)
Blinking red (1 Hz) Fan failure: check for an inoperative fan.
Blinking red (0.25 Hz) Power failure: check for an inoperative power supply.
Solid blue Local UID has been activated. Use this function to locate the server in a rack

environment.

Blinking blue (300 msec) Remote UID has been activated. Use this function to locate the server from a

remote location.

NIC1

Indicates network activity on LAN1 when fl ashing.

HDD

Indicates IDE channel activity when fl ashing.

2

1

3-4

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Power

Indicates power is being supplied to the system's power supply units. This LED
should normally be illuminated when the system is operating.

3-4 Hard Drive Carrier LEDs

Each hard drive carrier has two LEDs.

• Green: When illuminated, the green LED on the front of the drive carrier

indicates drive activity. A connection to the drive backplane enables this LED to
blink on and off when that particular drive is being accessed.

• Red: The red LED indicates two states. When blinking, it indicates the drive is

rebuilding. When solid, it indicates a drive failure. If a hard drive fails, you should
be notifi ed by your system management software. Please refer to Chapter 6 for
instructions on replacing failed hard drives.

4-1

Chapter 4: Warning Statements for AC Systems

Chapter 4

Standardized Warning Statements for AC Systems

4-1 About Standardized Warning Statements

The following statements are industry standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions
or experience difficulty, contact Supermicro's Technical Support department
for assistance. Only certifi ed technicians should attempt to install or confi gure
components.

Read this appendix in its entirety before installing or confi guring components in the
Supermicro chassis.

These warnings may also be found on our web site at http://www.supermicro.com/
about/policies/safety_information.cfm.

Warning Defi nition

Warning!

This warning symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.

警告の定義

この警告サインは危険を意味します。

人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、

電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。

此警告符号代表危险。

您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前，必须充分
意识到触电的危险，并熟练掌握防止事故发生的标准工作程序。请根据每项警告结
尾的声明号码找到此设备的安全性警告说明的翻译文本。

此警告符號代表危險。

您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前，請注意觸
電的危險，並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號
碼找到相關的翻譯說明內容。

4-2

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befi nden sich in einer Situation, die zu

Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den
Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung
vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen
Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes

de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y
familiarícese con los procedimientos estándar de prevención de accidentes. Al
fi nal de cada advertencia encontrará el número que le ayudará a encontrar el texto
traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES.

IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une

situation pouvant entraîner des blessures ou des dommages corporels. Avant
de travailler sur un équipement, soyez conscient des dangers liés aux circuits
électriques et familiarisez-vous avec les procédures couramment utilisées pour
éviter les accidents. Pour prendre connaissance des traductions des avertissements
fi gurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fi n de chaque avertissement.

CONSERVEZ CES INFORMATIONS.

ןונקת תורהצהאהרהז

ןה תואבה תורהצהא ינפמ שמתשמה תא ריהזהל תנמ לע ,היישעתה ינקת יפ לע תורהז הלבח

ה וא תולאש שיו הדימב .תירשפא תיזיפי ,יהשלכ היעבב תולקתרוציל שי הכימת תקלחמ םע רשק

רידגהל וא ןיקתהל םיאשר דבלב םיכמסומ םיאנכט .ורקימרפוס לש תינכט תאה .םיביכר

אורקל שי .ורקימרפוס יזראמב םיביכרה

תרדגה וא תנקתה ינפל ואולמב חפסנה תא

4-3

Warning Statements for AC Systems

안전을 위한 주의사항

경고!

이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수
있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와
관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준 작업절차를
준수해 주시기 바랍니다.

해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를
참조하십시오

BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die

lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,
dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's
en dient u op de hoogte te zijn van de standaard procedures om ongelukken te
voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te
herleiden naar de desbetreffende locatie.

BEWAAR DEZE INSTRUCTIES

. ﻲﻓ ﻚﻧﺍ ﻥﺃ ﻦﻜﻤﻳ ﺔﻟﺎﺣ ﻲﻓ ﺐﺒﺴﺘﺗ ﺔﺑﺎﺻﺍ ﺔﻳﺪﺴﺟ ﺰﻣﺮﻟﺍ ﺍﺬﻫ ﻲﻨﻌﻳ ﺮﻄﺧ !ﺮﻳﺬﺤﺗ

ﻥﺃ ﻞﺒﻗ ﻱﺃ ﻰﻠﻋ ﻞﻤﻌﺗ ﺕﺍﺪﻌﻣ،ﻛﻢﻠﻋ ﻰﻠﻋ ﻦ ﻦﻋ ﺔﻤﺟﺎﻨﻟﺍ ﺮﻁﺎﺨﻤﻟﺎﺑ ﺮﺋﺍﻭﺪﻟﺍ

ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ

ﻛﻭﺔﻳﺍﺭﺩ ﻰﻠﻋ ﻦ ﺭﺎﻤﻤﻟﺎﺑﺕﺎﺳ ﺔﻴﺋﺎﻗﻮﻟﺍ ﻟ ﻊﻨﻤﻉﻮﻗﻭ ﻱﺃﺙﺩﺍﻮﺣ

ﻢﻗﺭ ﻡﺪﺨﺘﺳﺍ ﻥﺎﻴﺒﻟﺍ ﺹﻮﺼﻨﻤﻟﺍ ﺔﻳﺎﻬﻧ ﻲﻓ ﺮﻳﺬﺤﺗ ﻞﻛ ﺭﻮﺜﻌﻠﻟ ﺎﻬﺘﻤﺟﺮﺗ

4-4

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Installation Instructions

Warning!

Read the installation instructions before connecting the system to the power source.

設置手順書
システムを電源に接続する前に、設置手順書をお読み下さい。

警告

将此系统连接电源前,请先阅读安装说明。

警告

將系統與電源連接前，請先閱讀安裝說明。

Warnung
Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen

lesen.

¡Advertencia!
Lea las instrucciones de instalación antes de conectar el sistema a la red de

alimentación.

Attention
Avant de brancher le système sur la source d'alimentation, consulter les directives

d'installation.

ﻟﺍ ﺕﺍﺩﺎﺷﺭﺇ ﺮﻗﺍﺐﻴﻛﺮﺘ ﻞﻴﺻﻮﺗ ﻞﺒﻗ ﻰﻟﺇ ﻡﺎﻈﻨﻟﺍ ﺔﻗﺎﻄﻠﻟ ﺭﺪﺼﻣ

אורקל שי רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תאחתמ.

시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오.

Waarschuwing
Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron

aansluit.

4-5

Chapter 4: Warning Statements for AC Systems

Circuit Breaker

Warning!

This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.

サーキット・ブレーカー

この製 品 は、短絡（過電流）保護装置がある建物での設置を前提としています。

保護装置の定格が250V、20Aを超えないことを確認下さい。

警告

此产品的短路(过载电流)保护由建筑物的供电系统提供,确保短路保护设备的额定电
流不大于250V,20A。

警告

此產品的短路(過載電流)保護由建築物的供電系統提供,確保短路保護設備的額定電
流不大於250V,20A。

Warnung
Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss-

bzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der
Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt.

¡Advertencia!
Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes)

del edifi cio. Asegúrese de que el dispositivo de protección no sea superior a: 250
V, 20 A.

Attention
Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit

dépend de l'installation électrique du local. Vérifi ez que le courant nominal du
dispositif de protection n'est pas supérieur à :250 V, 20 A.

לע ךמתסמ הז רצומנגהה תעינמל םינבמב תנקתומה יכ אדוול שי .ילמשח רצק

רצקה ינפמ ןגמה רישכמה ילמשחהמ רתוי אל אוה-

250 V, 20 A

4-6

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Power Disconnection Warning

Warning!

The system must be disconnected from all sources of power and the power cord
removed from the power supply module(s) before accessing the chassis interior to
install or remove system components.

電源切断の警告
システムコンポーネントの取り付けまたは取り外しのために、シャーシー内部にアクセス

するには、
システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り

外す必要があります。

警告

在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。

警告

在您打開機殼安裝或移除內部元件前，必須將系統完全斷電，並移除電源線。

경고!

이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에
의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지
않도록 해야 합니다.

Waarschuwing
Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van uw electrische

installatie. Controleer of het beveiligde aparaat niet groter gedimensioneerd is dan
220V, 20A.

ﺞﺘﻨﻤﻟﺍ ﺍﺬﻫ ﻰﻠﻋ ﺪﻤﺘﻌﻳ ﺕﺍﺪﻌﻣ ﺔﻳﺎﻤﺤﻟﺍ ﺓﺮﻴﺼﻘﻟﺍﺮﺋﺍﻭﺪﻟﺍ ﻦﻣ ﺎﻬﺘﻴﺒﺜﺗ ﻢﺗ ﻲﺘﻟﺍ ﻲﻓ

ﻰﻨﺒﻤﻟﺍ

20A, 250V : ﻦﻣ ﺪﻛﺄﺗ ﻥﺃ ﻢﻴﻴﻘﺗ ﺯﺎﻬﺠﻟﺍ ﻟﺍﻲﺋﺎﻗﻮ ﺲﻴﻟ ﻦﻣ ﺮﺜﻛﺃ

4-7

Chapter 4: Warning Statements for AC Systems

Warnung
Das System muss von allen Quellen der Energie und vom Netzanschlusskabel

getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es
auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder
zu entfernen.

¡Advertencia!
El sistema debe ser disconnected de todas las fuentes de energía y del cable

eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso
el interior del chasis para instalar o para quitar componentes de sistema.

Attention
Le système doit être débranché de toutes les sources de puissance ainsi que de

son cordon d'alimentation secteur avant d'accéder à l'intérieur du chassis pour
installer ou enlever des composants de systéme.

ילמשח קותינ ינפמ הרהזא

!הרהזא

למשחה תורוקמ לכמ תכרעמה תא קתנל שי ריסהל שיו קפסהמ ילמשחה לבכ תא

נקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפלת רסה ואת .םיביכר

ﻞﺼﻓ ﺐﺠﻳ ﻡﺎﻈﻨﻟﺍ ﻊﻴﻤﺟ ﻦﻣﺭﺩﺎﺼﻣ ﺔﻗﺎﻄﻟﺍ ﺔﻟﺍﺯﺇﻭ ءﺎﺑﺮﻬﻜﻟﺍ ﻚﻠﺳ ﻦﻣ ﺓﺪﺣﻭ ﺩﺍﺪﻣﺍ

ﺔﻗﺎﻄﻟﺍ ﻞﺒﻗ

ﻰﻟﺇ ﻝﻮﺻﻮﻟﺍ ﺔﻴﻠﺧﺍﺪﻟﺍ ﻖﻁﺎﻨﻤﻟﺍ ﻟﻞﻜﻴﻬﻠ ﺔﻟﺍﺯﺇ ﻭﺃ ﺖﻴﺒﺜﺘﻟ ﺕﺎﻧﻮﻜﻣ ﺯﺎﻬﺠﻟﺍ

경고!

시스템에 부품들을 장착하거나 제거하기 위해서는 섀시 내부에 접근하기 전에
반드시 전원 공급장치로부터 연결되어있는 모든 전원과 전기코드를 분리해주어야
합니다.

Waarschuwing
Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren

of verwijderen van systeem onderdelen, dient u alle spanningsbronnen en alle
stroomkabels aangesloten op de voeding(en) van de behuizing te verwijderen

4-8

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Equipment Installation

Warning!

Only trained and qualifi ed personnel should be allowed to install, replace, or service
this equipment.

機器の設置

トレーニングを受け認定された人だけがこの装置の設置、交換、またはサービスを許可

されています。

警告

只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。

警告

只有經過受訓且具資格人員才可安裝、更換與維修此設備。

Warnung
Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,

qualifi ziertem Personal gestattet werden.

¡Advertencia!
Solamente el personal califi cado debe instalar, reemplazar o utilizar este equipo.

Attention
Il est vivement recommandé de confier l'installation, le remplacement et la

maintenance de ces équipements à des personnels qualifi és et expérimentés.

!הרהזא

שר דבלב ךמסומ תווצתא ףילחהל ,ןיקתהל יא .דויצה רובע תוריש תתל וא דויצה

ﻦﻴﺑﺭﺪﻤﻟﺍﻭ ﻭ ﺐﻴﻛﺮﺘﻟﻝﺍﺪﺒﺘﺳﺍ ﻭﺃ ﺔﻣﺪﺧ ﺯﺎﻬﺠﻟﺍ ﺍﺬﻫ ﺢﻤﺴﻳ ﻥﺃ ﺐﺠﻳ ﻂﻘﻓ ﻦﻴﻠﻫﺆﻤﻟﺍ ﻦﻴﻔﻅﻮﻤﻠﻟ

경고!

훈련을 받고 공인된 기술자만이 이 장비의 설치, 교체 또는 서비스를 수행할 수
있습니다.

4-9

Chapter 4: Warning Statements for AC Systems

Restricted Area

Warning!

This unit is intended for installation in restricted access areas. A restricted access
area can be accessed only through the use of a special tool, lock and key, or other
means of security. (This warning does not apply to workstations).

アクセス制限区域

このユ ニットは、アクセス制限区域に設置されることを想定しています。

アクセス制限区域は、特別なツール、鍵と錠前、その他のセキュリティの手段を用いての
み出入りが可能です。

警告

此部件应安装在限制进出的场所，限制进出的场所指只能通过使用特殊工具、锁和
钥匙或其它安全手段进出的场所。

警告

此裝置僅限安裝於進出管制區域，進出管制區域係指僅能以特殊工具、鎖頭及鑰匙
或其他安全方式才能進入的區域。

Warnung
Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen.

Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und
Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich.

¡Advertencia!
Esta unidad ha sido diseñada para instalación en áreas de acceso restringido.

Sólo puede obtenerse acceso a una de estas áreas mediante la utilización de una
herramienta especial, cerradura con llave u otro medio de seguridad.

Attention
Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une

zone d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme
de verrouillage et une clé, ou tout autre moyen de sécurité.

Waarschuwing
Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door

geschoold en gekwalifi ceerd personeel.

4-10

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Battery Handling

Warning!

There is the danger of explosion if the battery is replaced incorrectly. Replace the
battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメー
カーが推奨する型、または同 等のものを使用下さい。 使用済電池は製造元の指示に従
って処 分して 下さい 。

警告

电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更

换原有电池。请按制造商的说明处理废旧电池。

警告

電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有

電池。請按照製造商的說明指示處理廢棄舊電池。

תלבגומ השיג םע רוזא

!הרהזא

תרזעב תנתינ השיגה .השיג תלבגה םהב שיש םירוזאב הדיחיה תא ןיקתהל שי

.('דכו לוענמ ,חתפמ) דבלב החטבא ילכ

. ﺺﻴﺼﺨﺗ ﺓﺪﺣﻮﻟﺍ ﻩﺬﻫ ﻲﻓ ﺎﻬﺒﻴﻛﺮﺘﻟ ﻖﻁﺎﻨﻣ ﺓﺭﻮﻈﺤﻣ ﻢﺗ

ﺻﻮﻟﺍ ﻦﻜﻤﻳﻰﻟﺇ ﻝﻮ ﺔﻘﻄﻨﻣ ﺓﺭﻮﻈﺤﻣ ﻂﻘﻓ ﻡﺍﺪﺨﺘﺳﺍ ﻝﻼﺧ ﻦﻣ ،ﺔﺻﺎﺧ ﺓﺍﺩﺃ

ﻭﺃ ﻱﺃ ﻼﻟ ﻯﺮﺧﺃ ﺔﻠﻴﺳﻭﻥﺎﻣﻷ ﺡﺎﺘﻔﻣﻭ ﻞﻔﻗ

경고!

이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다. 특수도구, 잠금 장치
및 키, 또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다.

Waarschuwing
Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang.

Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te
maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.

4-11

Chapter 4: Warning Statements for AC Systems

Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die

Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.

Attention
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer

que par une pile de type semblable ou équivalent, recommandée par le fabricant.
Jeter les piles usagées conformément aux instructions du fabricant.

¡Advertencia!
Existe peligro de explosión si la batería se reemplaza de manera incorrecta.

Reemplazar la batería exclusivamente con el mismo tipo o el equivalente
recomendado por el fabricante. Desechar las baterías gastadas según las
instrucciones del fabricante.

!הרהזא

תנכס תמייקץוציפ .הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי

גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ.

תוללוסה קוליס תושמושמה עצבל שי .ןרציה תוארוה יפל

ﺮﻄﺧ ﻙﺎﻨﻫ ﻦﻣ ﻝﺍﺪﺒﺘﺳﺍ ﺔﻟﺎﺣ ﻲﻓ ﺭﺎﺠﻔﻧﺍ ﺔﻳﺭﺎﻄﺒﻟﺍ ﺔﺤﻴﺤﺻ ﺮﻴﻏ ﺔﻘﻳﺮﻄﺑ ﻚﻴﻠﻌﻓ

ﺔﻳﺭﺎﻄﺒﻟﺍ ﻝﺍﺪﺒﺘﺳﺍ

ﻂﻘﻓ ﻉﻮﻨﻟﺍ ﺲﻔﻨﺑ ﺎﻬﻟﺩﺎﻌﻳ ﺎﻣ ﻭﺃ ﺎﻤﻛﺖﺻﻭﺃ ﺔﻌﻨﺼﻤﻟﺍ ﺔﻛﺮﺸﻟﺍ ﻪﺑ

ﺕﺎﻳﺭﺎﻄﺒﻟﺍ ﻦﻣ ﺺﻠﺨﺗ ﻟ ﺎﻘﻓﻭ ﺔﻠﻤﻌﺘﺴﻤﻟﺍﺔﻌﻧﺎﺼﻟﺍ ﺔﻛﺮﺸﻟﺍ ﺕﺎﻤﻴﻠﻌﺘ

경고!

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와
동일하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다.
제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.

Waarschuwing
Er is ontploffi ngsgevaar indien de batterij verkeerd vervangen wordt. Vervang de

batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen
wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd
te worden.

4-12

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Redundant Power Supplies

Warning!

This unit might have more than one power supply connection. All connections must
be removed to de-energize the unit.

冗長電源装置

このユニットは複数の電源装置が接続されている場合があります。

ユニットの電源を切るためには、すべての接続を取り外さなければなりません。

警告

此部件连接的电源可能不止一个，必须将所有电源断开才能停止给该部件供电。

警告

此裝置連接的電源可能不只一個，必須切斷所有電源才能停止對該裝置的供電。

Warnung
Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass

der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.

¡Advertencia!
Puede que esta unidad tenga más de una conexión para fuentes de alimentación.

Para cortar por completo el suministro de energía, deben desconectarse todas las
conexiones.

Attention
Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute

tension et tout courant électrique de l'unité, toutes les connexions d'alimentation
doivent être débranchées.

דחא קפסמ רתוי םייק םא

!הרהזא

.קפס לש דחא רוביחמ רתוי שי הדחיל תא ריסהל שי ןקורל תנמ לע םירוביחה לכ

חיה תאי.הד

4-13

Chapter 4: Warning Statements for AC Systems

Backplane Voltage

Warning!

Hazardous voltage or energy is present on the backplane when the system is
operating. Use caution when servicing.

バックプレーンの電圧
システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。
修理する際には注意ください。

警告

当系统正在进行时，背板上有很危险的电压或能量，进行维修时务必小心。

警告

當系統正在進行時，背板上有危險的電壓或能量，進行維修時務必小心。

Warnung
Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche

Spannungen oder Energien auf. Vorsicht bei der Wartung.

¡Advertencia!
Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso.

Tenga cuidado cuando lo revise.

. ﺪﻗ ﺍﺬﻬﻟ ﻥﻮﻜﻳ ﻟﺍﺯﺎﻬﺠ ﺕﻻﺎﺼﺗﺍ ﺓﺪﻋ ﺕﺍﺪﺣﻮﺑ ﺔﻗﺎﻄﻟﺍ ﺩﺍﺪﻣﺍ

ﺔﻟﺍﺯﺇ ﺐﺠﻳ ﺕﻻﺎﺼﺗﻻﺍ ﺔﻓﺎﻛ ﻝﺰﻌﻟ ﻟﺍﺓﺪﺣﻮ ﻦﻋ ءﺎﺑﺮﻬﻜﻟﺍ

경고!

이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에
전원을 차단하기 위해서는 모든 연결 단자를 제거해야만 합니다.

Waarschuwing
Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle

aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken.

4-14

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Comply with Local and National Electrical Codes

Warning!

Installation of the equipment must comply with local and national electrical codes.

地方および国の電気規格に準拠

機器の取り付けはその地方および国の電気規格に準拠する必要があります。

警告

设备安装必须符合本地与本国电气法规。

警告

設備安裝必須符合本地與本國電氣法規。

Warnung

Die Installation der Geräte muss den Sicherheitsstandards entsprechen.

ﻙﺎﻨﻫ ﺮﻄﺧ ﻦﻣ ﻲﺋﺎﺑﺮﻬﻜﻟﺍ ﺭﺎﻴﺘﻟﺍ ﻰﻠﻋ ﺓﺩﻮﺟﻮﻤﻟﺍ ﺔﻗﺎﻄﻟﺍﻭﺃ ﺔﺣﻮﻠﻟﺍ

ﻥﻮﻜﻳ ﺎﻣﺪﻨﻋﻡﺎﻈﻨﻟﺍ ﻞﻤﻌﻳ ﺪﻨﻋ ﺍﺭﺬﺣ ﻦﻛ ﺔﻣﺪﺧ ﺯﺎﻬﺠﻟﺍ ﺍﺬﻫ

경고!

시스템이 동작 중일 때 후면판 (Backplane)에는 위험한 전압이나 에너지가 발생
합니다. 서비스 작업 시 주의하십시오.

Waarschuwing
Een gevaarlijke spanning of energie is aanwezig op de backplane wanneer het

systeem in gebruik is. Voorzichtigheid is geboden tijdens het onderhoud.

ירוחאה לנפב חתמ

זא!הרה

ךלהמב רהזיהל שי .תכרעמה לועפת ןמזב ירוחאה לנפב חתמ תנכס תמייק

.הדובעה

Attention
Lorsque le système est en fonctionnement, des tensions électriques circulent sur

le fond de panier. Prendre des précautions lors de la maintenance.

4-15

Chapter 4: Warning Statements for AC Systems

Product Disposal

Warning!

Ultimate disposal of this product should be handled according to all national laws
and regulations.

製品の廃棄

この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が

あります。

警告

本产品的废弃处理应根据所有国家的法律和规章进行。

警告

本產品的廢棄處理應根據所有國家的法律和規章進行。

יצראה למשחה יקוח םואית

!הרהזא

תנקתה םייצראהו םיימוקמה למשחה יקוחל תמאות תויהל תבייח דויצה.

ﺕﺍﺪﻌﻤﻟﺍ ﺐﻴﻛﺮﺗ ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﻠﻟ ﻞﺜﺘﻤﻳ ﻥﺃ ﺐﺠﻳ ﻦﻴﻧﺍﻮﻘﺔﻴﻨﻁﻮﻟﺍﻭ ﺔﻴﻠﺤﻤﻟﺍ ﺔﻘﻠﻌﺘﻤﻟﺍ

ءﺎﺑﺮﻬﻜﻟﺎﺑ

¡Advertencia!
La instalacion del equipo debe cumplir con las normas de electricidad locales y
nacionales.Attention
L'équipement doit être installé conformément aux normes électriques nationales

et locales.

경고!

현 지역 및 국가의 전기 규정에 따라 장비를 설치해야 합니다.

Waarschuwing
Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale

elektriciteitsvoorschriften.

4-16

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Warnung

Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen

des Landes erfolgen.

¡Advertencia!

Al deshacerse por completo de este producto debe seguir todas las leyes y

reglamentos nacionales.

Attention

La mise au rebut ou le recyclage de ce produit sont généralement soumis à des

lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de

l'organisme compétent.

Easy Swap Fan Warning

Warning!

The fans might still be turning when you remove the fan assembly from the chassis.
Keep fi ngers, screwdrivers, and other objects away from the openings in the fan
assembly's housing.

ファン・ホットスワップの警告

シャーシから冷却ファン装置を取り外した際、ファンがまだ回転している可能性があり

ます。ファンの開口部に、指、ドライバー、およびその他のものを近づけないで下さい。

警告

רצומה קוליס

!הרהזא

ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס.הנידמה יקוח

ﻲﺋﺎﻬﻨﻟﺍ ﺺﻠﺨﺘﻟﺍ ﻦﻣ ﺞﺘﻨﻤﻟﺍ ﺍﺬﻫ ﻪﻌﻣ ﻞﻣﺎﻌﺘﻟﺍ ﻲﻐﺒﻨﻳ ﻟ ﺎﻘﻓﻭ ﻊﻴﻤﺠﺔﻴﻨﻁﻮﻟﺍ ﺢﺋﺍﻮﻠﻟﺍﻭ ﻦﻴﻧﺍﻮﻘﻟﺍ ﺪﻨﻋ

경고!

이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.

Waarschuwing

De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming

met alle nationale wetten en reglementen.

4-17

Chapter 4: Warning Statements for AC Systems

!הרהזא

יקלח תא םיריסמ רשאכ שי .םידבוע ןיידע םיררוואמהו ןכתי ,זראמהמ ררוואמה

קיחרהללררוואמה ךותב םיחתפהמ םינוש הדובע ילכו תועבצאה תא חוטב קחרמ

ﻦﻜﻤﻤﻟﺍ ﻦﻣ ﺡﻭﺍﺮﻤﻟﺍ ﻥﺃ ﻝﺍﺰﺗ ﻻ ﺔﻟﺍﺯﺇ ﺪﻨﻋﺭﻭﺪﺗ ﺔﻠﺘﻛ ﺔﺣﻭﺮﻤﻟﺍ ﻞﻜﻴﻬﻟﺍ ﻦﻣ ﺐﺠﻳ ءﺎﻘﺑﺇ

ﻊﺑﺎﺻﻷﺍ ﻭﻲﻏﺍﺮﺒﻟﺍ ﺕﺎﻜﻔﻣ

. ءﺎﻴﺷﻷﺍ ﻦﻣ ﺎﻫﺮﻴﻏﻭ ﺍﺪﻴﻌﺑ ﻦﻋ ﺕﺎﺤﺘﻔﻟﺍ ﻲﻓ ﺔﻠﺘﻛ ﺔﺣﻭﺮﻤﻟﺍ

경고!

섀시로부터 팬 조립품을 제거할 때 팬은 여전히 회전하고 있을 수 있습니다. 팬
조림품 외관의 열려있는 부분들로부터 손가락 및 스크류드라이버, 다른 물체들이
가까이 하지 않도록 배치해 주십시오.

当您从机架移除风扇装置，风扇可能仍在转动。小心不要将手指、螺丝起子和其他
物品太靠近风扇

警告

當您從機架移除風扇裝置，風扇可能仍在轉動。小心不要將手指、螺絲起子和其他
物品太靠近風扇。

Warnung
Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis

genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände
von den Öffnungen des Lüftergehäuses entfernt.

¡Advertencia!
Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador

del chasis. Mandtenga los dedos, los destornilladores y todos los objetos lejos de
las aberturas del ventilador

Attention
Il est possible que les ventilateurs soient toujours en rotation lorsque vous retirerez

le bloc ventilateur du châssis. Prenez garde à ce que doigts, tournevis et autres
objets soient éloignés du logement du bloc ventilateur.

4-18

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Power Cable and AC Adapter

Warning!

When installing the product, use the provided or designated connection cables,
power cables and AC adaptors. Using any other cables and adaptors could cause
a malfunction or a fi re. Electrical Appliance and Material Safety Law prohibits the
use of UL or CSA -certifi ed cables (that have UL/CSA shown on the code) for any
other electrical devices than products designated by Supermicro only.

電源コードとACアダプター
製品を設置する場合、提供または指定された接続ケーブル、電源コードとACアダプター

を使用下さい。他のケーブルやアダプタを使用すると故障や火災の原因になることがあ
ります。 電気用品安全法は、ULまたはCSA認定のケーブル(UL/CSEマークがコードに表

記)をSupermicroが指定する製品以外に使用することを禁止しています。

警告

安装此产品时,请使用本身提供的或指定的连接线,电源线和电源适配器.使用其它线
材或适配器可能会引起故障或火灾。除了Supermicro所指定的产品,电气用品和材
料安全法律规定禁止使用未经UL或CSA认证的线材。(线材上会显示UL/CSA符号)。

警告

安裝此產品時,請使用本身提供的或指定的連接線,電源線和電源適配器.使用其它線
材或適配器可能會引起故障或火災。除了Supermicro所指定的產品,電氣用品和材
料安全法律規定禁止使用未經UL或CSA認證的線材。(線材上會顯示UL/CSA符號)。

Warnung
Bei der Installation des Produkts, die zur Verfügung gestellten oder benannt

Anschlusskabel, Stromkabel und Netzteile. Verwendung anderer Kabel und Adapter
kann zu einer Fehlfunktion oder ein Brand entstehen. Elektrische Geräte und
Material Safety Law verbietet die Verwendung von UL-oder CSA-zertifi zierte Kabel,
UL oder CSA auf der Code für alle anderen elektrischen Geräte als Produkte von
Supermicro nur bezeichnet gezeigt haben.

Waarschuwing
Het is mogelijk dat de ventilator nog draait tijdens het verwijderen van het

ventilatorsamenstel uit het chassis. Houd uw vingers, schroevendraaiers en
eventuele andere voorwerpen uit de buurt van de openingen in de ventilatorbehuizing.

4-19

Chapter 4: Warning Statements for AC Systems

¡Advertencia!
Al instalar el producto, utilice los cables de conexión previstos o designados, los

cables y adaptadores de CA. La utilización de otros cables y adaptadores podría
ocasionar un mal funcionamiento o un incendio. Aparatos Eléctricos y la Ley de
Seguridad del Material prohíbe el uso de UL o CSA cables certifi cados que tienen
UL o CSA se muestra en el código de otros dispositivos eléctricos que los productos
designados por Supermicro solamente.

Attention
Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné.

L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement
ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit
l'utilisation de UL ou CSA câbles certifi és qui ont UL ou CSA indiqué sur le code
pour tous les autres appareils électriques que les produits désignés par Supermicro
seulement.

אתמו םיילמשחמ י

AC

!הרהזא

םימאתמו םיקפס ,םילבכב שמתשהל שי ,רצומה תא םיניקתמ רשאכ

AC רשא

וא הלקתל םורגל לוכי רחא םאתמ וא לבכ לכב שומיש .ךכ םשל וקפוסו ודעונ

טב יקוחו למשח ירישכמב שומיש יקוח יפ לע .ילמשח רצק רוסיא םייק ,תוחי

ב םיכמסומה םילבכב שמתשהל-

UL ב וא- CSA לש דוק םהילע עיפומ ראשכ)

UL/CSA( רחא ילמשח רצומ לכ רובע.דבלב ורקימקרפוס ידי לע ןיוצ אלש

ﺐﻴﻛﺮﺗ ﺪﻨﻋ ﻡﺍﺪﺨﺘﺳﺍ ﺐﺠﻳ ﺯﺎﻬﺠﻟﺍ ﻭ،ﻞﻴﺻﻮﺘﻟﺍ ﺕﻼﺑﺎﻛ ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﺕﻼﺑﺎﻜﻟﺍ

ﺕﻻﻮﺤﻣﻭ ﺩﺩﺮﺘﻤﻟﺍ ﺭﺎﻴﺘﻟﺍ

. ﻥﺃ ﻱﺃ ﻡﺍﺪﺨﺘﺳﺍ ﺕﻼﺑﺎﻛ ﺕﻻﻮﺤﻣﻭ ﻯﺮﺧﺃ ﺐﺒﺴﺘﻳ ﻲﻓ ﻞﻄﻋ ﺙﻭﺪﺣ ﻖﻳﺮﺣ ﻭﺃ . ﻲﺘﻟﺍ

ﻚﻟ ﺎﻫﺮﻴﻓﻮﺗ ﻢﺗ ﺞﺘﻨﻤﻟﺍ ﻊﻣ

UL ﻭﺃ CSA ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﺓﺰﻬﺟﻷﺍ ﺩﺍﻮﻣﻭ ﻥﻮﻧﺎﻗ ﺔﻣﻼﺴﻟﺍ ﻡﺍﺪﺨﺘﺳﺍ ﺮﻈﺤﻳ ﺕﻼﺑﺎﻜﻟﺍ

ﻞﺒﻗ ﻦﻣ ﺓﺪﻤﺘﻌﻣ

Supermicro ﺓﺰﻬﺟﺃ ﻯﺮﺧﺃ ﺔﻴﺋﺎﺑﺮﻬﻛ ﺮﻴﻏ ﺕﺎﺠﺘﻨﻤﻟﺍ ﺔﻨﻴﻌﻤﻟﺍ ﻞﺒﻗ ﻦﻣ ﻱﻷ

(UL/CSA ﻞﻤﺤﺗ ﻲﺘﻟﺍﺔﻣﻼﻋ )

경고!

제품을 설치할 때에는 제공되거나 지정된 연결케이블과 전원케이블, AC어댑터를
사용해야 합니다. 그 밖의 다른 케이블들이나 어댑터들은 고장 또는 화재의 원인이
될 수 있습니다. 전기용품안전법 (Electrical Appliance and Material Safety
Law)은 슈퍼마이크로에서 지정한 제품들 외에는 그 밖의 다른 전기 장치들을
위한 UL또는 CSA에서 인증한 케이블(전선 위에 UL/CSA가 표시)들의 사용을
금지합니다.

4-20

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Waarschuwing
Bij het installeren van het product, gebruik de meegeleverde of aangewezen kabels,

stroomkabels en adapters. Het gebruik van andere kabels en adapters kan leiden
tot een storing of een brand. Elektrisch apparaat en veiligheidsinformatiebladen wet
verbiedt het gebruik van UL of CSA gecertifi ceerde kabels die UL of CSA die op
de code voor andere elektrische apparaten dan de producten die door Supermicro
alleen.

Chapter 5: Advanced Serverboard Setup

5-1

Chapter 5

Advanced Serverboard Setup

This ch apter cover s the ste ps requi red to inst all pro ces sors a nd heats inks to the
X9DRW-iF serverboard, connect the data and power c ables and install add- on
cards . All ser verb oard jumpe rs and co nnect ions are de scrib ed and a layout an d
quick re ference chart are included in this chapter. Remember to close the chassis
comple t el y wh en y o u ha v e fi nished working on the serverboard to protect and cool
the system suf fi ciently.

5-1 Handling the Serverboard

Static electrical discharge can damage electronic com ponents. To prevent damage
to printed circuit boards, it is important to handle them very carefully (see Chapter

4). Also note that the size and weight of the serverboard can cause it to bend if
handled improperly, which may result in damage. To prevent the serverboard from
bending, keep one hand under the center of the board to support it when handling.

The following measures are generally suffi cient to protect your equipment from
static discharge.

Precautions

• Use a grounded wrist strap designed to prevent static discharge.

• T ouch a grounded metal object before removing any board from its antistatic bag.

• Handle a board by its edges only; do not touch its components, peripheral chips,

memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the serverboard, add-on cards and peripherals back into their antistatic

bags when not in use.

Unpacking

The serverboard is shipped in antistatic packaging to avoid static damage. When
unpacking the board, make sure the person handling it is static protected.

5-2

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Installing the LGA2011 Processor

1. There are two load levers on the LGA2011 socket. To open the socket cover,
fi rst press and release the load lever labeled 'Open 1st'.

OPEN 1st

OPEN 1st

WARNING!

WARNING!

Press down on Load Lever
labeled 'Open 1st'.

OPEN 1st

OPEN 1st

WARNING!

WARNING!

5-2 Processor and Heatsink Installation

Warning! When handling the processor package, avoid placing direct pressure on

the label area.
Warning! Always connect the power cord last, and always remove it before adding,

removing or changing any hardware components. Make sure that you install the
processor into the CPU socket before you install the CPU heatsink.

Important! If you buy a CPU separately, make sure that you use an Intel-certifi ed
multi-directional heatsink only.

Notes:

• Make sure to install the system board into the chassis before you install the

CPU heatsink.

• When receiving a server board without a processor pre-installed, make sure that

the plastic CPU socket cap is in place and none of the socket pins are bent;
otherwise, contact your retailer immediately.

• Refer to the Supermicro website for updates on CPU support.

Chapter 5: Advanced Serverboard Setup

5-3

2. Press the second load lever labeled 'Close 1st' to release the load plate that
covers the CPU socket from its locking position.

OPEN 1st

OP

EN

1s

t

WARNING!

WARNING!

OPEN 1st

OPEN 1st

WARNING!

WARNING!

Press down on

Load the Lever

labeled 'Close 1st'

Pull lever away

from the socket

3. With the lever labeled 'Close 1st' fully retracted, gently push down on
the 'Open 1st' lever to open the load plate. Lift the load plate to open it
completely.

Gently push down to pop the

load plate open.

OPEN 1st

OPEN 1st

WARNING!

WARNING!

WARNING!

WARNING!

4. Using your thumb and the index fi nger, remove the 'WARNING' plastic cap
from the socket.

WARNING!

5-4

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

5. Use your thumb and index fi nger to hold the CPU on its edges. Align the CPU
keys, which are semi-circle cutouts, against the socket keys.

Socket Keys

CPU Keys

6. Once they are aligned, carefully lower the CPU straight down into the socket.
(Do not drop the CPU on the socket. Do not move the CPU horizontally or
vertically. Do not rub the CPU against the surface or against any pins of the
socket to avoid damaging the CPU or the socket.)

Caution: You can only install the CPU inside the socket in one direction. Make sure
that it is properly inserted into the CPU socket before closing the load plate. If it doesn't
close properly, do not force it as it may damage your CPU. Instead, open the load
plate again and double-check that the CPU is aligned properly.

Chapter 5: Advanced Serverboard Setup

5-5

7. With the CPU inside the socket, inspect the four corners of the CPU to make
sure that the CPU is properly installed.

8. Close the load plate with the CPU inside the socket. Lock the lever labeled
'Close 1st' fi rst, then lock the lever labeled 'Open 1st' second. Use your
thumb to gently push the load levers down to the lever locks.

OPEN 1st

OPEN 1s

t

Push down and lock the
level labeled 'Close 1st'.

Gently close the

load plate.

OPEN 1st

OPEN 1st

Lever Lock

OPEN 1st

OPEN

1st

Lever Lock

Push down and lock

the lever labeled

'Open 1st'

5-6

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Installing a Passive CPU Heatsink

1. Do not apply any thermal grease to the heatsink or the CPU die -- the
required amount has already been applied.

2. Place the heatsink on top of the CPU so that the four mounting holes are
aligned with those on the serverboard's and the Heatsink Bracket underneath.

Note: The direction of the fi ns on the heatsink should align with the direction of
the airfl ow in your system.

3. Screw in two diagonal screws (i.e., the #1 and the #2 screws) until just snug
(-do not over-tighten the screws to avoid possible damage to the CPU.)

4. Finish the installation by fully tightening all four screws.

Note: The heatsink with the air tunnel (SNK-P0047PSC) needs to be at the CPU1
location with the air tunnel facing to the right (when looking from the front of the
system) in order to increase the airfl ow for CPU2 heat sink (SNK-P0047PS).

Figure 5-1. Installing the Heatsinks

Chapter 5: Advanced Serverboard Setup

5-7

Removing the Heatsink

Caution: We do not recommend that the CPU or the heatsink be removed. However,

if you do need to uninstall the heatsink, please follow the instructions below to uninstall
the heatsink to prevent damage done to the CPU or the CPU socket.

1. Unscrew the heatsink screws from the serverboard in the sequence as shown
in the illustration below.

2. Gently wriggle the heatsink to loosen it from the CPU. (Do not use excessive
force when wriggling the heatsink!)

3. Once the heatsink is loosened, remove it from the CPU socket.

4. Remove the used thermal grease and clean the surface of the CPU and the
heatsink, Reapply the proper amount of thermal grease on the surface before
reinstalling the CPU and the heatsink.

5-3 Connecting Cables

Now that the processors are installed, the next step is to connect the cables to the
serverboard. These include the data (ribbon) cables for the peripherals and control
panel and the power cables.

Connecting Data Cables

The cables used to transfer data from the peripheral devices have been carefully
routed in preconfi gured systems to prevent them from blocking the fl ow of cooling
air that moves through the system from front to back. If you need to disconnect
any of these cables, you should take care to reroute them as they were originally
after reconnecting them (make sure the red wires connect to the pin 1 locations). If
you are confi guring the system, keep the airfl ow in mind when routing the cables.

The following data cables (with their connector locations noted) should be connected.
See the serverboard layout diagram in this chapter for connector locations.

• Two SATA cables (connect onboard SATA 0~1 to backplane 8~9)

• Two Ipass to four SAS cables (connect onboard SAS 0~3 to backplane 0~3 and

onboard 4~7 to backplane 4~7)

• One SGPIO cable (connect to T-SGPIO1 to backplane sideband 3)

• Control Panel cable (JF1, see next page)

5-8

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Connecting Power Cables

The X9DRW-iF has a 24- pin p rim ar y powe r suppl y co nnec tor de sign ated "JPW1"
for con nec ti on to th e ATX power supp ly. Conne ct th e app ropr iate c on nec tor f rom
the power supply to JPW1 to supply power to the serverboard. See the Connector
Defi nitions sec tion in t his ch apter for p ower con necto r pin defi nitions.

In addition, your power supply must be connected to the two 8-pin and one 4-pin
Processor Power connectors at JPW3/3 and JPW4.

Connecting the Control Panel

JF1 contains header pins for various front control panel connectors. See Figure 5-1
for the pin locations of the various front control panel buttons and LED indicators.
Even and odd numbered pins are on opposite sides of each header.

All JF1 wires have been bundled into single keyed ribbon cable to simplify their
connection. The red wire in the ribbon cable plugs into pin 1 of JF1. Connect the
other end of the cable to the Control Panel printed circuit board, located just behind
the system status LEDs in the chassis.

Figure 5-2. Front Control Panel Header Pins (JF1)

NMI
x (key)
Vcc
Vcc
Vcc
Vcc
Vcc
Vcc
Reset
Power

Ground

x (key)

Power LED

HDD LED

NIC1
NIC2

OH/Fan Fail LED

Power Fail LED

Ground
Ground

2 1

20 19

Chapter 5: Advanced Serverboard Setup

5-9

5-4 I/O Ports

The I/O ports are color coded in conformance with the PC 99 specifi cation. See
Figure 5-3 below for the colors and locations of the various I/O ports.

Figure 5-3. Rear Panel I/O Ports

Rear I/O Ports

1. COM Port 1 (Turquoise) 6. Back Panel USB Port 3

2. Back Panel USB Port 0 7. Gigabit LAN 1

3. Back Panel USB Port 1 8. Gigabit LAN 2

4. IPMI_Dedicated LAN 9. Back Panel VGA (Blue)

5. Back Panel USB Port 2 10. UID Button

1

2

5

4

3 6 7

1

8

1

10

1

9

5-10

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Figure 5-4. Installing DIMM into Slot

5-5 Installing Memory

Caution! Exercise extreme care when installing or removing DIMM modules to prevent

any possible damage.

Memory Support

The X9DRW-iF supports up to 512 GB of registered ECC
1GB, 2GB, 4GB, 8GB, 16GB and 32GB size SDRAM in sixteen (16) DIMM slots
of up to DDR3 1600/1333/1066/800 MHz speed. See the following table for memory
installation.

Memory speed support is dependent on the type of CPU used on the board.

Installing Memory Modules

1. Insert the desired number of DIMMs into the memory slots, starting with
DIMMA1.. For best memory performance, please install memory modules
of the same type and same speed on the memory slots as indicated on the
tables below.

2. Insert each DIMM module vertically into its slot. Pay attention to the notch
along the bottom of the module to avoid installing incorrectly (see Figure 5-4).

3. Gently press down on the DIMM module until it snaps into place in the slot.
Repeat for all modules.

To Install: Insert
module vertically and
press down until it
snaps into place.
Pay attention to the
alignment notch at
the bottom.

To Remove: Use
your thumbs to gently
push the release tabs
near both ends of the
module. This should
release it from the
slot.

Top View of DDR3 Slot

Release Tab Release Tab

Note: Notch should align with

the receptive key point on
the slot.

Notch

Notch

Front View

Chapter 5: Advanced Serverboard Setup

5-11

Processors and their Corresponding Memory Modules

CPU# Corresponding DIMM Modules

CPU 1

P1­DIMMA1

P1­DIMMA2

P1­DIMMB1

P1­DIMMB2

P1­DIMMC1

P1­DIMMC2

P1­DIMMD1

P1­DIMMD2

CPU2

P2­DIMME1

P2­DIMME2

P2­DIMMF1

P2­DIMMF2

P2­DIMMG1

P2­DIMMG2

P2­DIMMH1

P2­DIMMH2

Processor and Memory Module Population

Number of
CPUs+DIMMs

CPU and Memory Population Confi guration Table
(*For memory to work proper, please install DIMMs in pairs)

1 CPU &
2 DIMMs

CPU1
P1-DIMMA1/P1-DIMMB1

1 CPU &
4 DIMMs

CPU1
P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1

1 CPU &
5~8 DIMMs

CPU1
P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1, P1-DIMMA2/P1-DIMMB2, P1­DIMMC2/P1-DIMMD2

2 CPUs &
4 DIMMs

CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1

2 CPUs &
6 DIMMs

CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1, P1-DIMMC1/P1-DIMMD1

2 CPUs &
8 DIMMs

CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1, P1-DIMMC1/P1-DIMMD1, P2­DIMMG1/P2-DIMMH1

2 CPUs &
9~12 DIMMs

CPU1/CPU2
P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1, P1-DIMMC1/P1-DIMMD1, P2­DIMMG1/P2-DIMMH1, P1-DIMMA2/P1-DIMMB2, P2-DIMME2/P2-DIMMF2

2 CPUs &
13 DIMMs~16
DIMMs

CPU1/CPU
P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1, P1-DIMMC1/P1-DIMMD1, P2­DIMMG1/P2-DIMMH1, P1-DIMMA2/P1-DIMMB2, P2-DIMME2/P2-DIMMF2,
P1-DIMMC2/P1-DIMMD2, P2-DIMMG2/P2-DIMMH2

UDIMM Support on the Intel E5-2600 Series Processor Platform

DIMMs Populated
per DDR Channel

UDIMM Type
(Unb. DIMM)

POR Speeds (in

MHz)

Ranks per DIMM

(Any Combination)

1 ECC/Non-ECC DDR3 1066, 1333 SR, DR
2 ECC/Non-ECC DDR3 1066, 1333 SR, DR

RDIMM Support on the Intel E5-2600 Series Processor Platform

DIMMs Populated
per DDR Channel

RDIMM Type
(Reg. DIMM)

POR Speeds (in

MHz)

Ranks per DIMM

(Any Combination)

1 Reg. ECC DDR3 1066, 1333, 1600 SR, DR
2 Reg. ECC DDR3 1066, 1333,1600 SR, DR
1 Reg. ECC DDR3 1066 QR
2 Reg. ECC DDR3 800 QR

5-12

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

LRDIMM Support on the Intel E5-2600 Series Processor Platform

DIMMs Populated
per DDR Channel

LRDIMM Type

(Load Reduced

DIMM)

POR Speeds (in

MHz)

Ranks per DIMM

(Any Combination)

1 LR ECC DDR3 1066, 1333 QR
2 LR ECC DDR3 1066, 1333 QR

Other Notes and Restrictions:

• For the memory modules to work properly, please install DIMM modules in pairs

(with even number of DIMMs installed).

• All channels in a system will run at the fastest common frequency.

• Due to memory allocation to system devices, the amount of memory that

remains ava ilable for ope rational use w ill be reduce d when 4 GB of R AM is
used. The reduction in memory availability is disproportional. See the following
table f or deta ils.

5-6 Adding PCI Expansion Cards

PCI Expansion Slots

One riser card is used to support PCI expansion cards in the system. The riser card
can support two PCI-E x16 full-height, 6.6" length expansion cards.

Installing a PCI Add-on Card

1. Remove the chassis cover.

2. Release the locking tab that corresponds to the PCI slot shield for the slot
you wish to populate.

3. Insert the expansion card into the riser card, pushing down with your thumbs
evenly on both sides of the card.

4. Slide the add-on card into the riser card and attach the add-on card bracket
in place of the PCI slot shield.

5. Secure the add-on card by closing the PCI slot shield lever.

6. Connect cables to the add-on card as necessary.

Note: If the left side riser is with 2 or more x8 PCI-E slots make sure an installed
card on the left side riser is detected. If it is not, then go to the system’s BIOS
Setup and in Advanced/ PCI/PnP Confi guration /SXB1 Confi guration BIOS setting
select the [2x8] option. Then save the BIOS setting changes and reboot the system.

Note: Go to www.supermicro.com/UIO/ for mor information.

Chapter 5: Advanced Serverboard Setup

5-13

Figure 5-5. X9DRW-iF Serverboard Layout

(not drawn to scale)

5-7 Serverboard Details

Notes:

• See Chapter 2 for detailed information on jumpers, I/O ports and JF1 front

panel connections.

• " " indicates the location of "Pin 1".

• Jumpers/LED Indicators not indicated are for testing only.

• Use only the correct type of onboard CMOS battery as specifi ed by the

manufacturer. Do not install the onboard battery upside down to avoid possible
explosion

SP1

JPW3

JPW2

JPW4

JPB1

FAN2

FAN1

FAN4

FANA

FAN3

JPI2C1

LED3

LED1

COM2

JTAG OF CPLD

SXB1A

SXB1B: CPU PCI-E 3.0 x16 + x16

P1-DIMMC1

CPU1

P1-DIMMC2

P1-DIMMD2

P1-DIMMD1

UID

SXB2: CPU2 PCI-E3.0 X16

LAN2

CPU2

LAN1

P1-DIMMB2

P1-DIMMA1

P1-DIMMA2

P1-DIMMB1

USB2/3

USB0/1

IPMI-LAN

P2-DIMMH1

P2-DIMMG2

P2-DIMMH2

P2-DIMMG1

COM1

P2-DIMMF2

P2-DIMMF1

P2-DIMME2

P2-DIMME1

X9DRW-3F/iF
Rev.1.02

VGA

LAN
CTRL

BIOS

BMC
CTRL

JPW1

PHY

JPL1

B1B2A1A2B1B2A1

A2

SXB1C

JVRM_I2C2

JVRM_I2C1

JPG1

JIPMB1

JSTBY1

JSD1

JD1

JI2C1

JI2C2

JL1

JF1

I-SATA1

I-SATA0

JLPC1

JSM1

JSM2

T-SGPIO1

T-SGPIO2

I-SATA3

I-SATA2

I-SATA5

I-SATA4

JBAT1

JPME2

JWD1

JPME1

JP3

FANB

1

LED2

SATA/

USB4/5

PCH

JBT1

SCU0~3

SATA/

SCU4~7

JVR1

JUIDB

JOH1

5-14

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

X9DRW-iF Quick Reference

Jumper Description Default Setting

JBT1 Clear CMOS See Chapter 3
JI2C1/JI2C2 SMB to PCI-E Slots Open (Normal)
JPB1 BMC Enable Pins 1-2 (Enabled)
JPG1 VGA Enable Pins 1-2 (Enabled)
JPL1 LAN1/LAN2 Enable Pins 1-2 (Enabled)
JWD1 Watch Dog Pins 1-2 (Reset)

LED Description State Status

LED1 BMC Green: Blinking Normal
LED2 Power LED Green: On SB Power On
LED3 UID LED Blue: On Unit Identifi ed

• The 6017R-NTF server uses the X9DRW-iF motherboard, which does not

include SAS ports or components.

Chapter 5: Advanced Serverboard Setup

5-15

Connector Description

COM1/COM2 Backplane COM Port1/Front Accessible COM2 Header
FAN1~4,FANA, FANB CPU/System Fan Headers
I-SATA 0~5 Intel PCH SATA Connectors 0~5
JBAT1 Onboard Battery (See Chpt. 4 for Used Battery Disposal)
JD1 Speaker/Power LED Connector (Pins 1~3: PWR LED, Pins 6~7:

Onboard Buzzer/Pins 4~7: External Speaker)

JF1 Front Panel Control Header
JIPMB1 4-pin External BMC I2C Header (for an IPMI Card)
JL1 Chassis Intrusion
JLPC1 Port80 Header
JOH1 Overheat/Fan Fail LED
JPI2C1 Power Supply SMBbus I2C Header
JPW1 ATX 24-Pin Power Connector (See Warning on Pg. 1-6)
JPW2/3 12V 8-Pin Power Connectors (See Warning on Pg. 1-6)
JPW4 12V 4-Pin Power Connector (See Warning on Pg. 1-6)
JSD1 SATA DOM (Device_On_Module) Power Connector
JSTBY1 Standby Power Connector
LAN1/2 G-bit Ethernet Ports 1/2
(IPMI) LAN IPMI_Dedicated LAN
SATA/SCU 0~3, 4~7 Serial_Link SATA/SCU Connections 0~3, 4~7 (for X9DRW-3F), SCU

0~3 (for X9DRW-iF)

SP1 Onboard Buzzer (Internal Speaker)
SXB1A SMC-Proprietary SPEC Slot (See Note 1 below.)
SXB1B SMC-Proprietary PCI-E 3.0 x16 + x16 Add-on Card Slot (Left) (See

Note 1 below.)

SXB1C SMC-Proprietary SPEC Slot (See Note 1 below.)
SXB2 SMC-Proprietary PCI-E 3.0 x16 Add-on Card Slot (Right) (See Note

2)

T-SGPI0 1/2 Serial-Link General_Purpose IO Headers 1/2
USB 0/1, 2/3 Back Panel USB 0/1, 2/3 Ports
USB 4/5 Front Panel Accessible USB 4/5 Connections
UID Switch UID (Unit Identifi er) Switch

Note 1: For SXB1A/SXB1B/SXB1C PCI-Exp. slots to work properly, please use an
SMC-proprietary riser card (eg. RSC-RIUW-2E16) in the slots.

Note 2: For SXB2 PCI-Exp. slot to work properly, please use the SMC-proprietary
riser card RSC-R2UW-2EBR or RSC-R1UW-E8R in the slot.

Note 3: Components not documented are reserved for internal use only.

5-16

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Warning! To prevent damage to the power supply or serverboard, please use a power
supply that contains a 24-pin, two 8-pin and one 4-pin power connectors. Be sure to
connect these power supply connectors to the 24-pin power connector (JPW1), the
two 8-pin power connectors (JPW2, JPW3) and the one 4-pin power connector (JPW4)
on the serverboard. Failure in doing so will void the manufacturer warranty on your
power supply and serverboard.

5-8 Connector Defi nitions

ATX Power 24-pin Connector

Pin Defi nitions (JPW1)

Pin# Defi nition Pin # Defi nition
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 COM 3 COM
16 PS_ON 4 +5V
17 COM 5 COM
18 COM 6 +5V
19 COM 7 COM
20 Res (NC) 8 PWR_OK
21 +5V 9 5VSB
22 +5V 10 +12V
23 +5V 11 +12V
24 COM 12 +3.3V

12V 8-pin PWR Connector

Pin Defi nitions (JPW2/3)

Pins Defi nition
1 through 4 Ground
5 through 8 +12V

Required Connections

Power Connectors

A 24-pin main power supply
connector(JPW1), two 8-pin CPU
power connectors (JPW2/JPW3) and
a 4-pin power connector are located
on the serverboard. These power
connectors meet the SSI EPS 12V
specifi cation. These power connectors
must also be connected to your power
supply. See the table on the right for
pin defi nitions.

Warning: To provide adequate power
supply to the serverboard, be sure to
connect the 24-pin ATX PWR (JPW1),
two 8-pin PWR connectors (JPW2/
JPW3) and the 4-pin PWR connector
(JPW4) to the power supply. Failure
to do so will void the manufacturer
warranty on your power supply and
serverboard.

Chapter 5: Advanced Serverboard Setup

5-17

Reset Connector

The reset connector is located on pins
3 and 4 of JF1 and attaches to the
reset switch on the computer chassis.
See the table on the right for pin
defi nitions.

PW_ON Connector

The Power Button connection is
located on pins 1 and 2 of JF1.
Momentarily contacting both pins will
power on/off the system. This button
can also be confi gured to function as
a suspend button (with a setting in the
BIOS - See Chapter 5). To turn off the
power when the system is in suspend
mode, press the button for 4 seconds
or longer. Refer to the table on the right
for pin defi nitions.

Reset Button

Pin Defi nitions

(JF1)

Pin# Defi nition
3 Reset
4 Ground

Power Button

Pin Defi nitions

(JF1)

Pin# Defi nition
1 PW_ON
2 Ground

Overheat/Fan Fail LED (OH)

Conne ct an LED cabl e to pins 7 and
8 of Front Control Panel to use the
Overheat/Fan Fail/Power Fail and UID
LED connections. The Red LED on pin
7 provid es warnings of overhe at, fan
failure o r p o wer f a il u re. T h e B l ue L ED
on pin 8 wor ks as th e fro nt pane l UID
LED indicator. The Red LED takes
precedence over the Blue LED by
default . Refer to t he t abl e on t he r ig ht
for pin de fi nitions.

OH/Fan Fail/ PWR Fail/Blue_

UID LED Pin Defi nitions (JF1)

Pin# Defi nition
7 Red_LED-Cathode/OH/Fan

Fail/Power Fail5.5V.SB

8 Blue_UID LED

OH/Fan Fail/PWR Fail

LED Status (Red LED)

State Indication
Off Normal
On Overheat
Flashing Fan Fail

Power Fail LED

The Power Fail LED connection
is located on pins 5 and 6 of JF1.
Refer to the t able on the r ight for pin
defi nitions.

PWR Fail LED

Pin Defi nitions (JF1)

Pin# Defi nition
5 3.3V
6 PWR Supply Fail

5-18

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

NMI Button

The non-maskable interrupt button
header is located on pins 19 and 20
of JF1. Refer to the table on the right
for pin defi nitions.

NMI Button

Pin Defi nitions

(JF1)

Pin# Defi nition
19 Control
20 Ground

HDD LED

The HDD LED connection is located
on pins 13 and 14 of JF1. Attach the
hard drive LED cable here to display
disk activity (for any hard drives on the
system, including SAS, Serial ATA and
IDE). See the table on the right for pin
defi nitions

HDD LED

Pin Defi nitions

(JF1)

Pin# Defi nition
13 3.3V Standby
14 HD Active

Power On LED

The Power On LED connector is
located on pins 15 and 16 of JF1. This
connection is used to provide LED
indication of power being supplied to
the system. See the table on the right
for pin defi nitions.

Power LED

Pin Defi nitions

(JF1)

Pin# Defi nition
15 3.3V
16 PWR LED

NIC1 LED

Pin Defi nitions (JF1)

Pin# Defi nition
9 NIC 2 Activity LED
10 NIC 2 Link LED
11 NIC 1 Activity LED
12 NIC 1 Link LED

NIC1 (LAN1) LED

The NIC (Network Interface Controller)
LED connections for GLAN port 1 are
located on pins 11 and 12 of JF1, and
the LED connection for GLAN Port 2
are on Pins 9 and 10. Attach the NIC
LED cables here to display network
activity. Refer to the table on the right
for pin defi nitions.

Chassis Intrusion

A Chassis Intrusion header is located
at JL1 on the serverboard. Attach an
appropriate cable from the chassis to
inform you of a chassis intrusion when
the chassis is opened.

Chapter 5: Advanced Serverboard Setup

5-19

Video Connection

One video (VGA) port (VGA1) is
located next to LAN Port 2 on the I/O
backplane. Refer to the board layout
below for the location.

Universal Serial Bus (USB)

Four Universal Serial Bus ports (USB
0/1, 2/3) are located on the I/O back
panel. In addition, one USB header,
located next to COM2 port, provides
two front-accessible USB connections
(USB 4/5). (Cables are not included).
See the tables on the right for pin
defi nitions.

FP USB (4/5)

Pin Defi nitions

USB 4, 8,10, 6, 7
Pin # Defi nition

USB 5, 9, 11
Pin # Defi nition

1 +5V 1 +5V
2 PO- 2 PO­3 PO+ 3 PO+
4 Ground 4 Ground
5 NC 5 Key

(NC = No connection)

Backplane

USB (0/1, 2/3)

Pin Defi nitions

Pin# Defi nition
1 +5V
2 PO­3 PO+
4 Ground
5NA

Ethernet Ports

Two Gigabit Ethernet ports (LAN1/2)
are located on the I/O backplane on
the serverboard to provide internet
connections. In addition, an IPMI_
Dedicated LAN, located above USB
0/1 ports on the backplane, provides
KVM support for IPMI 2.0. All these
ports accept RJ45 type cables.

LAN Ports

Pin Defi nition (LAN 1/2)

Pin# Defi nition Pin# Defi nition
1 P2V5SB 10 SGND
2 TD0+ 11 Act LED
3 TD0- 12 P3V3SB
4 TD1+ 13 Link 100 LED

(Yellow, +3V3SB)

5 TD1- 14 Link 1000 LED

(Yellow, +3V3SB)

6 TD2+ 15 Ground
7 TD2- 16 Ground
8 TD3+ 17 Ground
9 TD3- 18 Ground

(NC = No Connection)

5-20

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

PWR LED Connector

Pin Defi nitions (JD1)

Pin Setting Defi nition
Pin 1 Anode (+)
Pin 2 Cathode (-)
Pin 3 NA

Speaker Connector

Pin Defi nitions

Pin Setting Defi nition
Pins 4~7 External Speaker
Pins 6~7 Internal Speaker

(Default)

Fan Header

Pin Defi nitions

Pin# Defi nition
1 Ground
2 +12V
3 Tachometer
4 PWR Modulation

Fan Headers

This serverboard has six system/CPU
fan headers (Fan 1~Fan 4, Fan A,
Fan B) on the serverboard. All these
4-pin fans headers are backward
compatible with the traditional 3-pin
fans. However, fan speed control is
available for 4-pin fans only. The fan
speeds are controlled by Thermal
Management via Hardware Monitoring
in the Advanced Setting in the BIOS.
(See Chapter 5 for more details.) See
the table on the right for pin defi nitions.

Power LED/Speaker

On JD1 header, pins 1-3 are used for
power LED indication, and pins 4-7 are
for the speaker. See the tables on the
right for pin defi nitions. Please note
that the speaker connector pins (4-7)
are used with an external speaker. If
you wish to use the onboard speaker,
you should close pins 6-7 with a
jumper.

Serial Port Pin Defi nitions

(COM1/COM2)

Pin # Defi nition Pin # Defi nition
1 DCD 6 DSR
2 RXD 7 RTS
3 TXD 8 CTS
4 DTR 9 RI
5 Ground 10 NC

(NC = No connection)

Serial Ports

Two COM connections (COM1 &
COM2) are located on the serverboard.
COM1 is located on the Backplane I/O
panel. COM2, located next to Front
Accessible USB 4/5, is used to provide
front access serial support. See the
table on the right for pin defi nitions.

Chapter 5: Advanced Serverboard Setup

5-21

Unit Identifi er Switch

A Unit Identifier (UID) Switch and
two LED Indicators are located on
the serverboard. The UID Switch is
located next to the VGA port. The
Rear UID LED (LED3) is located next
to the UID Switch. The Front Panel
UID LED is located at Pins 7/8 of the
Front Control Panel at JF1. Connect a
cable to Pin 8 on JF1 for Front Panel
UID LED indication. When you press
the UID switch, both Rear UID LED
and Front Panel UID LED Indicators
will be turned on. Press the UID switch
again to turn off both LED Indicators.
These UID Indicators provide easy
identifi cation of a system unit that may
be in need of service.

Note: UID can also be triggered via
IPMI on the serverboard. For more
information on IPMI, please refer to
the IPMI User's Guide posted on our
Website @

http://www.supermicro.

com.

UID Switch

Pin# Defi nition
1 Ground
2 Ground
3 Button In
4 Ground

UID LED Status

Color/State OS Status
Blue: On Windows OS Unit Identifi ed
Blue: Blink-

ing

Linux OS Unit Identifi ed

Power Bu tton

Blue+ (OH/Fan Fail/
PWR FaiL/UID LED)

1

NIC1 Link LED

Reset Button

2

Power Fail LED

HDD LED

FP PWRLED

Reset

PWR

3.3 V

ID_UID_SW/3/3V Stby

Red+ (Blue LED Cathode)

Ground

Ground

1920

3.3V

X

Ground

NMI

X

NIC2 Link LED

NIC2 Activity LED

NIC1 Activity LED

Internal Speaker

The Internal Speaker, located at
SP1, can be used to provide audible
indications for various beep codes.
See the table on the right for pin
defi nitions. Refer to the layout below
for the locations of the Internal Buzzer
(SP1).

Internal Buzzer (SP1)

Pin Defi nition

Pin# Defi nitions
Pin 1 Pos. (+) Beep In
Pin 2 Neg. (-) Alarm

Speaker

5-22

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Overheat LED/Fan Fail

The JOH1 header is used to connect
an LED indicator to provide warnings
of chassis overheating and fan failure.
This LED will blink when a fan failure
occurs. Refer to the tables on right for
pin defi nitions.

Overheat LED

Pin Defi nitions

(JOH1)

Pin# Defi nition
1 VDC
2 OH Active

OH/Fan Fail LED

Status

State Message
Solid Overheat
Blinking Fan Fail

Power SMB (I2C) Connector

Power System Management Bus (I2C)
Connector (JI2C1) monitors power
supply, fan and system temperatures.
See the table on the right for pin
defi nitions.

PWR SMB

Pin Defi nitions

(JI2C1)

Pin# Defi nition
1 Clock
2 Data
3 PWR Fail
4 Ground
5 +3.3V

Port 80 Header

A Port 80 header, located at JLPC1,
provides Port 80 support. Port 80 is
an "Ask and Respond" port between
a client machine and a host server.
Port 80 allows the HTML (Hyper
Text Markup Language) codes to be
translated into web page displays so
that you will see the web pages instead
of the HTML codes when you browse
the internet. See the table on the right
for pin defi nitions.

Port 80 Header

Pin Defi nitions

(JLPC1)

Pin # Defi nition
1 +3.3V
2 LFRAME#
3 LCLK
4 LAD 3
5 LRESET#
6 LAD2
7 Ground
8 LAD0

Chapter 5: Advanced Serverboard Setup

5-23

IPMB Header

Pin Defi nitions

(JIPMB1)

Pin# Defi nition
1 Data
2 Ground
3 Clock
4 No Connection

IPMB

A System Management Bus header for
IPMI 2.0 is located at JIPMB1. Connect
the appropriate cable here to use the
IPMB I

2

C connection on your system.

T-SGPIO 1/2 Headers

Two SGPIO (Serial-Link General
Purpose Input/Output) headers are
located on the serverboard. These
headers support Serial_Link interface
for onboard SATA connections. See
the table on the right for pin defi nitions.

DOM Power Connector

A power connector for SATA DOM
(Disk_On_Module) devices is located
at JSD1. Connect an appropriate cable
here to provide power support for your
DOM devices.

DOM Power

Connector

Pin Defi nitions

Pin# Defi nition
1 +5V
2 Ground
3 Ground

SGPIO Header Pin Defi nitions

(T-SGPIO1/T-SGPIO2)

Pin# Defi nition Pin# Defi nition
1 NC 2 Data In
3 Ground 4 Data Out
5 Load 6 Ground
7 Clock 8 NC

(NC = No Connection)

Standby Power Connector

The Standby Power connection
header is located at JSTBY1 on the
serverboard. See the table on the right
for pin defi nitions. (You must also have
a cable to use this feature.)

Standby Power

Pin Defi nitions

Pin# Defi nition
1 +5V Standby
2 Ground
3 Wake-up

5-24

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Legacy Wake-On-LAN Header
(JSTBY)

The onboard LAN por ts do not need
a WOL header to support their Wake­On-LAN function. Instead, the legacy
WOL header was preserved (JSTBY)
to provide convenience for some
embedded customers who need an
internal power source from the board.
See the table on the right for pin
defi nitions.

Legacy Wake-

On-LAN Header

Pin Defi nitions

(JSTBY)

Pin# Defi nition
1 +5V Standby
2 Ground
3 Wake-up (signal)

Chapter 5: Advanced Serverboard Setup

5-25

5-9 Jumper Settings

Explanation of Jumpers

To modify the operation of the
serverboard, jumpers can be used
to choose between optional settings.
Jumpers create shorts between two
pins to change the function of the
connector. Pin 1 is identifi ed with a
square solder pad on the printed circuit
board. See the diagram at right for
an example of jumping pins 1 and 2.
Refer to the serverboard layout page
for jumper locations.

Note: On two-pin jumpers, "Closed"
means the jumper is on and "Open"
means the jumper is off the pins.

Connector

Pins

Jumper

Setting

3 2 1

3 2 1

JBT1 contact pads

CMOS Clear

JBT1 is used to clear CMOS, which will also clear any passwords. Instead of pins,
this jumper consists of contact pads to prevent accidentally clearing the contents
of CMOS.

To Clear CMOS

1. First power down the system and unplug the power cord(s). It is also
recommended that you remove the onboard battery from the serverboard.

2. With the power disconnected, short the CMOS pads with a metal object such
as a small screwdriver.

3. Remove the screwdriver (or shorting device).

4. Reconnect the power cord(s) and power on the system.

Note 1. For an ATX power supply, you must completely shut down the system,
remove the AC power cord, and then short JBT1 to clear CMOS.

Note 2. Be sure to remove the onboard CMOS Battery before you short JBT1 to
clear CMOS.

Note 3. Clearing CMOS will also clear all passwords.
Note 4: Do not use the PW_ON connector to clear CMOS.

5-26

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Watch Dog Enable/Disable

Watch Dog (JWD1) is a system mon i­tor that can reboot the system when
a software application hangs. Close
Pins 1-2 to reset t he system if an ap ­plication hangs. Close Pins 2-3 to gen­erate a non -mask able inter rupt si gnal
for the application that hangs. See the
table o n the right f or jumper set tings.
Watch Dog must also be enabled in
the BIOS.

Watch Dog Enable/Disable

Jumper Settings (JWD)

Jumper Setting Defi nition
Pins 1-2 Reset
Pins 2-3 NMI
Open Disabled

VGA Enable/Disable

Jumper Settings (JPG1)

Jumper Setting Defi nition
Pins 1-2 Enabled
Pins 2-3 Disabled

VGA Enable/Disable

Jumper JPG1 allows the user to
enable the onboard VGA connector.
The default setting is 1-2 to enable the
connection. See the table on the right
for jumper settings.

BMC Enable

Jumper JPB1 allows you to enable
the embedded the Renesas BMC
(Baseboard Management) Controller
to provide IPMI 2.0/KVM support on
the serverboard. See the table on the
right for jumper settings.

BMC Enable/Disable

Jumper Settings (JPB1)

Jumper Setting Defi nition
Pins 1-2 BMC Enable
Pins 2-3 Normal (Default)

I2C Bus to PCI-Exp. Slots

Jumpers JI2C1 and JI2C2 allow you
to connect the System Management
Bus (I2C) to PCI-Express slots. The
default setting is Open to disable the
connection. See the table on the right
for jumper settings.

I2C to PCI-Exp

Jumper Setting

Jumper Setting Defi nition
Closed Enabled
Open Disabled (Default)

LAN Enable/Disable

JPL1 enables or disables the GLAN
Port1/GLAN Port2 on the serverboard.
See the table on the right for jumper
settings. The default setting is Enabled.

LAN Enable/Disable

Jumper Settings (JPL1)

Jumper Setting Defi nition
Pins 1-2 Enabled (default)
Pins 2-3 Disabled

Chapter 5: Advanced Serverboard Setup

5-27

5-10 Onboard Indicators

Onboard Power LED

An Onboard Power LED is located
at LE1 on the serverboard. When
this LED is on, the system is on. Be
sure to turn off the system and unplug
the power cord before removing or
installing components. See the tables
at right for more information.

Onboard PWR LED Indicator

LED Settings (LE1)

LED Color Defi nition
Off System Off (PWR cable not

connected)

Green System On
Green:

Flashing
Quickly

ACPI S1 State

IPMI Dedicated LAN LEDs

In addition to LAN 1/LAN 2, an IPMI
Dedicated LAN is also located on the
I/O Backplane of the serverboard.
The amber LED on the right indicates
connection and activity , while the green
LED on the left indicates the speed of
the connection. See the tables at right
for more information.

IPMI LAN
Link/Speed LED (Left)
& Activity LED (Right)

Color Status Defi nition
Off Off No Connection
Green:

Solid

Link/
Speed
(Left)

100 Mb/s

Amber
Blinking

Activity
(Right)

Active

IPMI LAN

Activity LEDLink LED

GLAN LEDs

The LAN 1/2 ports are located on the
IO Backplane. Each Ethernet LAN port
has two LEDs. The Yellow LED on the
right indicates activity. The Link LED
on the left may be green, amber or off
to indicate the speed. See the tables
at right for more information.

Activity
LED

Link Speed

LED

GLAN LED

GLAN Activity Indicator

(Right) LED Settings

Color Status Defi nition
Off No Connections
Yellow Flashing Active

LAN Connection Speed

Indicator (Left) LED Settings

LED Color Defi nition
Off 10 MHz
Green 100 MHz
Amber 1 GHz

5-28

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

BMC Heartbeat LED

A BMC Heartbeat LED is located at
DM1 on the serverboard. When DM1 is
blinking, BMC functions normally. See
the table at right for more information.

BMC Heartbeat LED

Status

Color/State Defi nition
Green:

Blinking

BMC: Normal

5-11 SATA Drive Connections

Rear UID LED

The rear U ID LED is lo cated at LE D3
on the rear of the serverboard. This
LED is used in conjunction with the
rear UID switch to provide easy
identifi cation of a system that might be
in need of service. Refer to UID Switch
on Page 2-17 for more infor matio n.

UID LED

Status

Color/State Status
Blue: On Unit Identifi ed
Blue: On Unit Identifi ed

Note: For more information on SATA HostRAID configuration, please
refer to the Intel SATA HostRAID User's Guide posted on our Website @
http://www.supermicro.com.

SATA/SCU

Pin Defi nitions

Pin# Defi nition
1 Ground
2 TX_P
3 TX_N
4 Ground
5 RX_N
6 RX_P
7 Ground

SATA/SC8U Ports

There are six Serial ATA ports
(I-SATA0~I-SATA 5) located on the
serverboard, including four SATA2
ports and two SATA3 ports. There
are also eight SCU ports (0~3, 4~7)
located on the X9DRW-3F, and four
SCU ports (SCU 0~3) located on the
X9DRW-iF. These ports provide serial­link signal connections, which are
faster than the connections of Parallel
ATA. See the table on the right for pin
defi nitions.

Chapter 5: Advanced Serverboard Setup

5-29

Figure 5-6. Driver/Tool Installation Display Screen

5-12 Installing Software

The Supermicro ftp site contains drivers and utilities for your system at ftp://ftp.

supermicro.com. Some of these must be installed, such as the chipset driver.

After accessing the ftp site, go into the CDR_Images directory and locate the ISO
fi le for your motherboard. Download this fi le to create a CD/DVD of the drivers and
utilities it contains. (You may also use a utility to extract the ISO fi le if preferred.)

Another option is to go to the Supermicro Website at

http://www.supermicro.com/
products/. Find the product page for your motherboard here, where you may

download individual drivers and utilities.
After creating a CD/DVD with the ISO fi les, insert the disk into the CD/DVD drive

on your system and the display shown in Figure 5-6 should appear.

5-30

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Note: Click the icons showing a hand writing on paper to view the readme fi les
for each item. Click the computer icons to the right of these items to install each
item (from top to the bottom) one at a time. After installing each item, you must
re-boot the system before moving on to the next item on the list. The bottom
icon with a CD on it allows you to view the entire contents.

SuperDoctor III

The SuperDoctor® III program is a web-based management tool that supports
remote management capability. It includes Remote and Local Management tools.
The local management is called SD III Client. The SuperDoctor III program allows
you to monitor the environment and operations of your system. SuperDoctor III
displays crucial system information such as CPU temperature, system voltages
and fan status. See the fi gures below for examples of the SuperDoctor III interface.

Note: The default User Name and Password for SuperDoctor III is ADMIN / ADMIN.
Note: When SuperDoctor III is fi rst installed, it adopts the temperature threshold

settings that have been set in BIOS. Any subsequent changes to these thresholds
must be made within SuperDoctor III, as the SuperDoctor III settings override the
BIOS settings. To set the BIOS temperature threshold settings again, you would
fi rst need to uninstall SuperDoctor III.

Figure 5-7. Supero Doctor III Interface Display Screen (Health Information)

Chapter 5: Advanced Serverboard Setup

5-31

Note: The SuperDoctor III program and User’s Manual can be downloaded from the
Supermicro web site at http://www.supermicro.com/products/accessories/software/

SuperDoctorIII.cfm. For Linux, we recommend that you use the SuperoDoctor II

application instead.

Figure 5-8. Supero Doctor III Interface Display Screen (Remote Control)

5-32

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

5-13 Serverboard Battery

Caution: There is a danger of explosion if the onboard battery is installed upside

down, which will reverse its polarites (see Figure 5-9). This battery must be replaced
only with the same or an equivalent type recommended by the manufacturer
(CR2032). Dispose of used batteries according to the manufacturer's instructions.

Figure 5-9. Installing the Onboard Battery

Please handle used batteries carefully. Do not damage the battery in any way; a
damaged battery may release hazardous materials into the environment. Do not
discard a used battery in the garbage or a public landfi ll. Please comply with the
regulations set up by your local hazardous waste management agency to dispose
of your used battery properly.

OR

Chapter 6: Advanced Chassis Setup

6-1

Chapter 6

Advanced Chassis Setup

This chapter covers the steps required to install components and perform
maintenance on the SC815TQ-R700WB/600WB chassis. For component
installation, follow the steps in the order given to eliminate the most common
problems encountered. If some steps are unnecessary, skip ahead to the next step.

Tools Required: The only tool you will need to install components and perform
maintenance is a Philips screwdriver.

6-1 Static-Sensitive Devices

Electrostatic discharge (ESD) can damage electronic com ponents. To prevent
damage to any printed circuit boards (PCBs), it is important to handle them very
carefully. The following measures are generally suffi cient to protect your equipment
from ESD damage.

Precautions

• Use a grounded wrist strap designed to prevent static discharge.

• T ouch a grounded metal object before removing any board from its antistatic bag.

• Handle a board by its edges only; do not touch its components, peripheral chips,

memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the serverboard, add-on cards and peripherals back into their antistatic

bags when not in use.

• For grounding purposes, make sure your computer chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and
the serverboard.

6-2

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Figure 6-1. Chassis: Front and Rear Views

6-2 Control Panel

The control panel (located on the front of the chassis) must be connected to the JF1
connector on the serverboard to provide you with system status indications. These
wires have been bundled together as a ribbon cable to simplify the connection.

Connect the cable from JF1 on the serverboard to the appropriate header on the
Control Panel PCB (printed circuit board). Make sure the red wire plugs into pin 1
on both connectors. Pull all excess cabling out of the airfl ow path.

The control panel LEDs inform you of system status. See "Chapter 3: System
Interface" for details on the LEDs and the control panel buttons. Details on JF1 can
be found in "Chapter 5: Advanced Serverboard Setup."

6-3 System Fans

Five 4-cm heavy duty counter-rotating fans provide the cooling for the SuperServer
6017R-WRF/NTF. Each fan unit is actually made up of two fans joined back-to­back, which rotate in opposite directions. This counter-rotating action generates
exceptional airfl ow and works to dampen vibration levels. It is very important that
the chassis top cover is properly installed and making a good seal in order for the
cooling air to circulate properly through the chassis and cool the components. See
Figure 6-2.

System Reset

Control PanelSystem LEDs

Main Power Hard Drive Bays

Slim DVD-ROM Drive

Power Supply Modules PCI Expansion Slots (w/ Riser Cards)

USB Ports

COM1 Port

VGA PortEthernet Ports

IPMI Port

Chapter 6: Advanced Chassis Setup

6-3

System Fan Failure

Fan speed is controlled by system temperature via a BIOS setting. If a fan fails,
the remaining fan will ramp up to full speed and the overheat/fan fail LED on the
control panel will turn on. Replace any failed fan at your earliest convenience with
the same type and model (the system can continue to run with a failed fan).

Remove the top chassis cover while the system is still running to determine which of
the fans has failed. Then power down the system before replacing a fan. Removing
the power cords is also recommended as a safety precaution.

Replacing System Fans

1. After determining which fan has failed, turn off the power to the system.

2. Unplug the fan cable from the serverboard and remove the failed fan from the

chassis.

3. Replace the failed fan with an identical 4-cm, 12 volt fan (available from

Supermicro: p/n FAN-0086L4).

4. Push the new fan into the vacant space in the housing while making sure

the arrows on the top of the fan (indicating air direction) point in the same
direction as the arrows on the other fans.

Figure 6-2. System Cooling Fans

Optional Fan

6-4

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Accessing the Drive Bays

Hard Drives: Because of their hotswap capability, you do not need to access the
inside of the chassis or power down the system to install or replace SATA drives.
Proceed to the next section for instructions.

DVD-ROM Drive: For installing/removing a DVD-ROM drive, you will need to gain
access to the inside of the SuperServer 6017R-WRF/NTF by removing the top
cover of the chassis. Proceed to the "DVD-ROM Drive Installation" section later in
this chapter for instructions.

Note: Only a "slim" DVD-ROM drive will fi t into the SuperServer 6017R-WRF/NTF.

Figure 6-3. Removing the Front Bezel

1. Unlock

2. Press release knob

3. Remove bezel assembly

5. Reposition the fan housing back over the two mounting posts in the chassis,
then reconnect the fan wires to the same chassis fan headers you removed
them from.

6. Power up the system and check that the fan is working properly and that
the LED on the control panel has turned off. Finish by replacing the chassis
cover.

6-4 Drive Bay Installation/Removal

Removing the Front Bezel

If your system has a front bezel (optional) attached to the chassis, you must fi rst
remove it to gain access to the drive bays. To remove the bezel, fi rst unlock the
front of the chassis then press the release knob (see Figure 6-3). Carefully remove
the bezel with both hands. A fi lter located within the bezel can be removed for
replacement/cleaning. It is recommended that you keep a maintenance log of
fi lter cleaning/replacement, since its condition will affect the airfl ow throughout the
whole system.

Chapter 6: Advanced Chassis Setup

6-5

Hard Drive Installation

The hard drives are mounted in drive carriers to simplify their installation and
removal from the chassis. These carriers also help promote proper airfl ow for
the drive bays. For this reason, even empty carriers without drives installed must
remain in the chassis.

Mounting a Hard Drive in a Drive Carrier

1. Insert a drive into the carrier with the printed circuit board side facing down so
that the mounting holes align with those in the carrier.

2. Secure the drive to the carrier with six screws, as shown in Figure 6-4.

Figure 6-4. Mounting a Hard Drive in a Carrier

Caution: Use caution when working around the hard drive backplane. Do not touch the

backplane with any metal objects and make sure no ribbon cables touch the backplane
or obstruct the holes, which aid in proper airfl ow.

Caution: Regardless of how many hard drives are installed, all drive carriers must
remain in the drive bays to maintain proper airfl ow.

6-6

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Installing/Removing a Hard Drive

1. To remove a carrier, push the release button located beside the drive LEDs.

2. Swing the colored handle fully out and use it to pull the unit straight out (see
Figure 6-5).

Note: Your operating system must have RAID support to enable the hot-plug ca­pability of the hard drives.

Figure 6-5. Removing a Hard Drive from the Server

DVD-ROM Drive Installation

The top cover of the chassis must be opened to gain full access to the DVD-ROM
drive bay. The SuperServer 6017R-WRF/NTF accomodates only slim-line DVD­ROM drives. Side mounting brackets are needed to mount a slim-line DVD-ROM
drive in the SuperServer 6017R-WRF/NTF server. Y ou must power down the system
before installing or removing a DVD-ROM drive.

Warning: Enterprise level hard disk drives are recommended for use in
Supermicro chassis and servers. For information on recommended HDDs,
visit the Supermicro Web site at

http://www.supermicro.com/products/nfo/fi les/

storage/SAS-CompList.pdf

Chapter 6: Advanced Chassis Setup

6-7

Removing the Chassis Cover

1. Grasp the two handles on either side and pull the unit straight out until it
locks (you will hear a "click").

2. Depress the two buttons on the top of the chassis to release the top cover
and at the same time, push the cover away from you until it stops. You can
then lift the top cover from the chassis to gain full access to the inside of the
server.

Removing/Installing a Drive

1. With the chassis cover removed, unplug the power and data cables from the
drive you want to remove.

2. Locate the locking tab at the rear of the drive. It will be on the left side of the
drive when viewed from the front of the chassis.

3. Pull the tab away from the drive and push the drive unit out the front of the
chassis.

4. Add a new drive by following this procedure in reverse order. You may hear a
faint *click* of the locking tab when the drive is fully inserted.

5. Remember to reconnect the data and power cables to the drive before
replacing the chassis cover and restoring power to the system.

6-5 Power Supply

The SuperServer 6017R-WRF/NTF has either a redundant 700 Watt (Model # PWS­704P-1R) consisting of two hot-swap power modules or a single 600 Watt (Model
# PWS-605P-1H) power supply confi guration. The power supply modules have an
auto-switching capability, which enables them to automatically sense and operate
with a 100V - 240V input voltage.

Redundant Power Supply Failure

If either of the two redundant power supply modules fail, the other module will
take the full load and allow the system to continue operation without interruption.
The Universal Information LED on the control panel will blink slowly and remain so
until the failed module has been replaced. Replacement modules can be ordered
directly from Supermicro (see contact information in the Preface). The power supply
modules have a hot-swap capability, meaning you can replace the failed module
without powering down the system.

6-8

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Replacing the Power Supply

You do not need to shut down the system to replace a power supply module. The
redundant feature will keep the system up and running while you replace the failed
hot-swap module. Replace with the same model, which can be ordered directly from
Supermicro (see Contact Information in the Preface).

1. First unplug the power cord from the failed power supply module.

2. To remove the failed power module, push the release tab (on the back of the
power supply) to the side and then pull the module straight out (see Figure
6-6).

3. The power supply wiring was designed to detach automatically when the
module is pulled from the chassis.

4. Replace the failed power module with another power supply module.

5. Simply push the new power supply module into the power bay until you hear
a click.

6. Finish by plugging the AC power cord back into the module.

Figure 6-6. Removing/Replacing the Power Supply

Chapter 7: BIOS

7-1

Chapter 7

BIOS

7-1 Introduction

This chapter describes the AMI BIOS Setup Utility for the SuperServer
6017R-WRF/NTF. The AMI ROM BIOS is stored in a Flash EEPROM and can be
easily updated. This chapter describes the basic navigation of the AMI BIOS Setup
Utility setup screens.

Starting the Setup Utility

To enter the BIOS Setup Utility, hit the <Delete> key while the system is booting-up.
(In most cases, the <Delete> key is used to invoke the BIOS setup screen. There
are a few cases when other keys are used, such as <F1>, <F2>, etc.) Each main
BIOS menu option is described in this manual.

The Main BIOS screen has two main frames. The left frame displays all the options
that can be confi gured. “Grayed-out” options cannot be confi gured. The right frame
displays the key legend. Above the key legend is an area reserved for a text
message. When an option is selected in the left frame, it is highlighted in white. Often
a text message will accompany it. (Note that BIOS has default text messages built
in. We retain the option to include, omit, or change any of these text messages.)
Settings printed in Bold are the default values.

A " "indicates a submenu. Highlighting such an item and pressing the <Enter>
key will open the list of settings within that submenu.

The BIOS setup utility uses a key-based navigation system called hot keys. Most
of these hot keys (<F1>, <F10>, <Enter>, <ESC>, <Arrow> keys, etc.) can be used
at any time during the setup navigation process.

7-2 Main Menu

When you fi rst enter AMI BIOS Setup Utility, you will see the Main Menu screen.
You can always return to the Main Menu by selecting the Main tab on the top of
the screen with the arrow keys.

The Main Menu screen provides you with a system overview, which includes the
version, built date and ID of the AMIBIOS, the type, speed and number of the
processors in the system and the amount of memory installed in the system.

7-2

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

System Time/System Date

You can edit this fi eld to change the system time and date. Highlight System Time
or System Date using the <Arrow> keys. Enter new values through the keyboard.
Press the <Tab> key or the <Arrow> keys to move between fi elds. The date must
be entered in DAY/MM/DD/YYYY format. The time is entered in HH:MM:SS format.
Please note that time is in a 24-hour format. For example, 5:30 A.M. appears as
05:30:00 and 5:30 P.M. as 17:30:00.

7-3 Advanced Settings Menu

Use the arrow keys to select Advanced Setup and press <Enter> to access the
following submenu items.

Boot Features

Quiet Boot

This feature allows the user to select bootup screen display between POST
messages and the OEM logo. Select Disabled to display the POST messages.
Select Enabled to display the OEM logo instead of the normal POST messages.
The options are Enabled and Disabled.

AddOn ROM Display Mode

Use this item to set the display mode for the Option ROM. Select Keep Current to
use the current AddOn ROM Display setting. Select Force BIOS to use the Option
ROM display mode set by the system BIOS. The options are Force BIOS and
Keep Current.

Bootup Num-Lock

Use this fe ature to set the Powe r-on state for t he Numloc k key. The op tions are
Of f and On.

Wait For 'F1' If Error

Selec t Enabl ed to fo rce t he system t o wait unt il the ' F1' key is pressed i f an er ror
occu rs. Th e optio ns are Di sable d and Enabled.

Interrupt 19 Capture

Interrupt 19 is the software interrupt that handles the boot disk function. When this
item is set to Enabled, the ROM BIOS of the host adaptors will "capture" Interrupt 19
at bootup and allow the drives that are attached to these host adaptors to function as
bootable disks. If this item is set to Disabled, the ROM BIOS of the host adaptors will

Chapter 7: BIOS

7-3

not capture Interrupt 19, and the drives attached to these adaptors will not function
as bootable devices. The options are Enabled and Disabled.

Power Confi guration

Watch Dog Function

If enabl ed, t he Watch D o g tim er w ill a ll ow th e syste m to re bo ot wh en it i s inac t ive
for more t han 5 minu tes. The o ption s are Enabl ed and Disabled.

Power Button Function

If this feature is set to Instant Off, the system will power off immediately as soon
as the user presses the power button. If this feature is set to 4 Seconds Override,
the system will power off when the user presses the power button for 4 seconds or
longer. The options are Instant Off and 4 Seconds Override.

Restore on AC Power Loss

Use this feature to set the power state after a power outage. Select Stay Off for the
system power to remain off after a power loss. Select Power-On for the system
power to be turned on after a power loss. Select Last State to allow the system
to resume its last state before a power loss. The options are Stay Off, Power On,
and Last State.

7-4

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

CPU Confi guration

This submenu displays the information of the CPU as detected by the BIOS. It also
allows the user to confi gure the CPU settings.

Socket 1 CPU Information/Socket 2 CPU Information

This submenu displays the following information regarding the CPUs installed
in Socket 1/ Socket 2.

• Type of CPU

• CPU Signature

• Microcode Patch

• CPU Stepping

• Maximum CPU Speed

• Minimum CPU Speed

• Processor Cores

• Intel HT (Hyper-Threading) Technology

• Intel VT-x Technology

• Intel SMX Technology

• L1 Data Cache

• L1 Code Cache

• L2 Cache

• L3 Cache

CPU Speed

This item displays the speed of the CPU installed in Socket 1/Socket 2.

64-bit

This item indicates if the CPU installed in Socket 1 or Socket 2 supports 64-bit
technology.

Clock Spread Spectrum

Select Enable to enable Clock Spectrum support, which will allow the BIOS to
monitor and attempt to reduce the level of Electromagnetic Interference caused by
the components whenever needed. The options are Disabled and Enabled.

Hyper-threading

Select Enabled to support Intel Hyper-threading Technology to enhance CPU
performance. The options are Enabled and Disabled.

Chapter 7: BIOS

7-5

Active Processor Cores

Set to Enabled to use a processor's second core and above. (Please refer to Intel's
website for more information.) The options are All, 1, 2, and 4.

Limit CPUID Maximum

This feature allows the user to set the maximum CPU ID value. Enable this function
to boot the legacy operating systems that cannot support processors with extended
CPUID functions. The options are Disabled (for the Windows OS), and Enabled.

Execute Disable Bit Capability (Available if supported by the OS & the CPU)

Select Enabled to enable the Execute Disable Bit which will allow the processor to
designate areas in the system memory where an application code can execute and
where it cannot, thus preventing a worm or a virus from fl ooding illegal codes to
overwhelm the processor or damage the system during an attack. The options are

Enabled and Disabled. (Refer to Intel and Microsoft W eb sites for more information.)

Intel® AES-NI

Select Enable to use the Intel Advanced Encryption Standard (AES) New
Instructions (NI) to ensure data security. The options are Enabled and Disabled.

Hardware Prefetcher (Available when supported by the CPU)

If set to Enabled, the hardware prefetcher will prefetch streams of data and
instructions from the main memory to the L2 cache to improve CPU performance.
The options are Disabled and Enabled.

Adjacent Cache Line Prefetch (Available when supported by the CPU)

The CPU prefetches the cache line for 64 bytes if this feature is set to Disabled.
The CPU prefetches both cache lines for 128 bytes as comprised if this feature is
set to Enabled.

DCU Streamer Prefetcher (Available when supported by the CPU)

Select Enabled to support Data Cache Unite (DCU) prefetch to speed up data
accessing and processing in the DCU to enhance CPU performance. The options
are Disabled and Enabled.

DCU IP Prefetcher

Select Enabled for DCU (Data Cache Unit) IP Prefetcher support, which will prefetch
IP addresses to improve network connectivity and system performance. The options
are Enabled and Disabled.

7-6

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Intel® Virtualization Technology (Available when supported by the CPU)

Select Enabled to support Intel Virtualization Technology, which will allow one
platform to run multiple operating systems and applications in independent
partitions, creating multiple "virtual" systems in one physical computer. The options
are Enabled and Disabled.

Note: If there is any c hang e to thi s set tin g, you wi ll nee d to powe r of f and re sta r t
the system for the change to take effect. Please refer to Intel’s website for detailed
information.)

CPU Power Management Confi guration

This submenu allows the user to confi gure the following CPU Power Management
settings.

Power Technology

Select Energy Effi cient to support power-saving mode. Select Custom to
customize system power settings. Select Disabled to disable power-saving
settings. The options are Disabled, Energy Effi cient, and Custom. If the option
is set to Custom, the following items will display:

EIST (Available when Power Technology is set to Custom)

EIST (Enhanced Intel SpeedStep Technology) allows the system to
automatically adjust processor voltage and core frequency to reduce power
consumption and heat dissipation. The options are Disabled (GV3 Disabled),
and Enabled (GV3 Enabled). (Note: GV3 is Intel Speedstep support used
on older platforms.)Please refer to Intel’s website for detailed information.)

Turbo Mode (Available when Power Technology is set to Custom)

Select Enabled to use the Turbo Mode to boost system performance. The
options are Enabled and Disabled.

C1E (Available when Power Technology is set to Custom)

Select Enabled to enable Enhanced C1 Power State to maximize energy
effi ciency. The options are Enabled and Disabled.

CPU C3 Report (Available when Power Technology is set to Custom)

Select Enabled to allow the BIOS to report the CPU C3 State (ACPI C2) to
the operating system. During the CPU C3 State, the CPU clock generator is
turned off. The options are Enabled and Disabled.

Chapter 7: BIOS

7-7

CPU C6 Report (Available when Power Technology is set to Custom)

Select Enabled to allow the BIOS to report the CPU C6 State (ACPI C3) to
the operating system. During the CPU C6 State, the power to all cache is
turned off. The options are Enabled and Disabled.

CPU C7 Report (Available when Power Technology is set to Custom)

Select Enabled to allow the BIOS to report the CPU C7 State (ACPI C3) to
the operating system. CPU C7 State is a processor-specifi c low C-State. The
options are Enabled and Disabled.

Package C-State limit (Available when Power Technology is set to
Custom)

This feature allows the user to set the limit on the C-State package register.
The options are C0, C2, C6, and No Limit.

Factory Long Duration Power Limit

This item displays the power limit set by the manufacturer during which long
duration power is maintained.

Long Duration Power Limit

This item displays the user-defi ned power limit (in watts) during which long
duration power is maintained.

Factory Long Duration Maintained (Available when Power Technology
is set to Custom)

This item displays the period of time set by the manufacturer during which
long duration power is maintained.

Long Duration Maintained

This item displays the period of time in seconds during which long duration
power is maintained.

Recommended Short Duration Power

This item displays the short duration power settings recommended by the
manufacturer.

Short Duration Power Limit

This item displays the time period during which short duration power is
maintained.

7-8

SUPERSERVER 6017R-WRF/NTF USER'S MANUAL

Chipset Confi guration

North Bridge

This feature allows the user to confi gure the settings for the Intel North Bridge.

Integrated IO Confi guration

Intel VT-d

Select Enabled to enable Intel Virtualization Technology support for Direct I/O
VT-d by reporting the I/O device assignments to the VWM (Virtual Working
Memory) through the DMAR ACPI Tables. This feature offers fully-protected
I/O resource sharing across Intel platforms, providing greater reliability, security
and availability in networking and data-sharing. The options are Disabled and

Enabled.

Intel I/OAT

The Intel I/OAT (I/O Acceleration Technology) significantly reduces CPU
overhead by leveraging CPU architectural improvements, freeing the system
resource for other tasks. The options are Disabled and Enabled.

DCA Support

Select Enabled to use Intel's DCA (Direct Cache Access) Technology to improve
data transfer effi ciency. The options are Disabled and Enabled.

IIO 1 PCIe Port Bifurcation Control/ IIO 2 PCIe Port Bifurcation Control

This submenu confi gures the following IO PCIe Port Bifurcation Control settings
for IIO 1 PCIe ports or IIO 2 PCIe ports to determine how the available PCI­Express lanes are distributed between the PCI-Express Root Ports.

IIO 2 PCIe Port

This item confi gures IOU2-PCIe Port settings. The options are: x4x4x4x4,
x4x4x8, x8x4x4, x8x8, x16 and Auto.

IIO 3 PCIe Port

This item confi gures IOU3-PCIe Port settings. The options are: x4x4x4x4,
x4x4x8, x8x4x4, x8x8, x16 and Auto.