Supero SUPERSERVER 6017R-N3RF4+, SUPERSERVER 6017R-N3RFT+ User Manual

SUPER

SUPERSERVER

6017R-N3RF4+

6017R-N3RFT+

®

USER’S MANUAL

1.0a

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu­mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environ­ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the manufacturer’s instruction manual, may cause harmful interference
with radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case you will be required to correct the interference at your own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn­ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to the
State of California to cause birth defects and other repro­ductive harm.

Manual Revision 1.0a
Release Date: Janaury 15, 2013

Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.

Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2013 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

Preface

About This Manual

This manual is written for professional system integrators and PC technicians.
It provides information for the installation and use of the SuperServer 6017R­N3RF4+/6017R-N3RFT+. Installation and maintenance should be performed by
experienced technicians only.

Manual Organization

Chapter 1: Introduction

The fi rst chapter provides a checklist of the main components included with the
server system and describes the main features of the serverboard and the chassis.

Preface

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer into a rack and
check out the server confi guration prior to powering up the system. If your server
was ordered without processor and memory components, this chapter will refer you
to the appropriate sections of the manual for their installation.

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.

Chapter 4: System Safety

You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 6017R-N3RF4+/6017R-N3RFT+.

Chapter 5: Advanced Serverboard Setup

Chapter 5 provides detailed information on the X9DRW-3LN4F+/X9DRW-3TF+
serverboard, including the locations and functions of connections, headers and
jumpers. Refer to this chapter when adding or removing processors or main memory
and when reconfi guring the serverboard.

iii

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the SC819TQ-R700WB server chas­sis. You should follow the procedures given in this chapter when installing, removing
or reconfi guring SAS or peripheral drives and when replacing system power supply
modules and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed informa­tion on running the CMOS Setup Utility.

Appendix A: BIOS Error Beep Codes

Appendix B: System Specifi cations

iv

Notes

Preface

v

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Table of Contents

Chapter 1 Introduction

1-1 Overview ......................................................................................................... 1-1

1-2 Serverboard Features ..................................................................................... 1-2

Processors ...................................................................................................... 1-2

Memory ........................................................................................................... 1-2

Onboard SAS .................................................................................................. 1-2

Onboard Serial ATA ........................................................................................ 1-2

Rear I/O Ports ................................................................................................. 1-2

Graphics Controller ......................................................................................... 1-2

1-3 Server Chassis Features ................................................................................ 1-3

System Power ................................................................................................. 1-3

Hard Drives ..................................................................................................... 1-3

PCI Expansion Slots ....................................................................................... 1-3

Front Control Panel ......................................................................................... 1-3

Cooling System ............................................................................................... 1-3

1-4 Contacting Supermicro .................................................................................... 1-5

Chapter 2 Server Installation

2-1 Overview ......................................................................................................... 2-1

2-2 Unpacking the System .................................................................................... 2-1

2-3 Preparing for Setup ......................................................................................... 2-1

Choosing a Setup Location ............................................................................. 2-1

2-4 Warnings and Precautions! ............................................................................. 2-2

Rack Precautions ............................................................................................ 2-2

Server Precautions .......................................................................................... 2-2

Rack Mounting Considerations ....................................................................... 2-3

Ambient Operating Temperature ................................................................ 2-3

Reduced Airfl ow ......................................................................................... 2-3

Mechanical Loading ................................................................................... 2-3

Circuit Overloading ..................................................................................... 2-3

Reliable Ground ......................................................................................... 2-3

2-5 Installing the System into a Rack ................................................................... 2-4

Identifying the Sections of the Rack Rails ...................................................... 2-4

Installing the Inner Rails ................................................................................. 2-4

Installing the Outer Rails ................................................................................. 2-5

Installing the Server into a Telco Rack ........................................................... 2-6

vi

Table of Contents

Chapter 3 System Interface

3-1 Overview ......................................................................................................... 3-1

3-2 Control Panel Buttons ..................................................................................... 3-1

UID .................................................................................................................. 3-1

Reset ............................................................................................................... 3-1

Power .............................................................................................................. 3-1

3-3 Control Panel LEDs ........................................................................................ 3-2

Information LED .............................................................................................. 3-2

NIC2 ................................................................................................................ 3-2

NIC1 ................................................................................................................ 3-2

HDD ................................................................................................................. 3-2

Power .............................................................................................................. 3-3

3-4 Drive Carrier LEDs .......................................................................................... 3-3

Chapter 4 Standardized Warning Statements for AC Systems

4-1 About Standardized Warning Statements ....................................................... 4-1

Warning Defi nition ........................................................................................... 4-1

Installation Instructions .................................................................................... 4-4

Circuit Breaker ................................................................................................ 4-5

Power Disconnection Warning ........................................................................ 4-6

Equipment Installation ..................................................................................... 4-8

Restricted Area ................................................................................................ 4-9

Battery Handling ............................................................................................ 4-10

Redundant Power Supplies .......................................................................... 4-12

Backplane Voltage ........................................................................................ 4-13

Comply with Local and National Electrical Codes ........................................ 4-14

Product Disposal ........................................................................................... 4-15

Hot Swap Fan Warning ................................................................................. 4-16

Power Cable and AC Adapter ...................................................................... 4-18

Chapter 5 Advanced Serverboard Setup

5-1 Handling the Serverboard ............................................................................... 5-1

Precautions ..................................................................................................... 5-1

Unpacking ....................................................................................................... 5-1

5-2 Installing the Processor and Heatsink ............................................................ 5-2

Installing an LGA2011 Processor .................................................................... 5-2

Installing a CPU Heatsink ............................................................................... 5-5

Removing the Heatsink ................................................................................... 5-5

5-3 Connecting Cables .......................................................................................... 5-6

Connecting Data Cables ................................................................................. 5-6

vii

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Connecting Power Cables .............................................................................. 5-6

Connecting the Control Panel ......................................................................... 5-6

5-4 I/O Ports .......................................................................................................... 5-7

5-5 Installing Memory ............................................................................................ 5-8

5-6 Adding PCI Cards ..........................................................................................5-11

5-7 Serverboard Details ...................................................................................... 5-12

X9DRW-3LN4F+/X9DRW-3TF+ Quick Reference ........................................ 5-13

5-8 Connector Defi nitions .................................................................................... 5-15

5-9 Jumper Settings ............................................................................................ 5-23

5-10 Onboard Indicators ........................................................................................ 5-25

5-11 SAS/SATA Port Connections ......................................................................... 5-26

5-12 Installing Software ......................................................................................... 5-27

SuperDoctor III .............................................................................................. 5-28

5-13 Onboard Battery ............................................................................................ 5-30

Chapter 6 Advanced Chassis Setup

6-1 Static-Sensitive Devices .................................................................................. 6-1

Precautions ..................................................................................................... 6-1

6-2 Control Panel .................................................................................................. 6-2

6-3 System Fans ................................................................................................... 6-3

System Fan Failure ......................................................................................... 6-3

Hard Drive Installation ..................................................................................... 6-5

Hard Drive Backplane ..................................................................................... 6-6

DVD-ROM Drive Installation ........................................................................... 6-7

6-4 Power Supply .................................................................................................. 6-8

Power Supply Failure ...................................................................................... 6-8

Chapter 7 BIOS

7-1 Introduction ...................................................................................................... 7-1

7-2 Main Setup ...................................................................................................... 7-2

7-3 Advanced Setup Confi gurations...................................................................... 7-3

7-4 Event Logs .................................................................................................... 7-24

7-5 IPMI ............................................................................................................... 7-26

7-6 Boot ............................................................................................................... 7-28

7-7 Security ......................................................................................................... 7-29

7-8 Save & Exit ................................................................................................... 7-30

Appendix A BIOS Error Beep Codes
Appendix B System Specifi cations

viii

Chapter 1: Introduction

Chapter 1

Introduction

1-1 Overview

The SuperServer 6017R-N3RF4+/6017R-N3RFT+ is a high-end server comprised of
two main subsystems: the SC819TQ-R700WB 1U server chassis and the X9DRW­3LN4F+/X9DRW-3TF+ dual processor serverboard. Please refer to our web site for
information on operating systems that have been certifi ed for use with the system
(www.supermicro.com).

In addition to the serverboard and chassis, various hardware components have been
included with the 6017R-N3RF4+/6017R-N3RFT+, as listed below:

• Six 4-cm fans (FAN-0101L4)

• One air shroud (MCP-310-19003-0N)

• Two passive CPU heatsinks (SNK-P0047PS)

• Riser Cards: (see Section 5-6 for details)

One RSC-R1UW-2E16-O-P
One RSC-R1UW-E8R-O-P

• SAS/SATA Accessories

One SAS backplane (BPN-SAS-815TQ)
Four drive carriers (MCP-220-00075-0B)

• One rackmount kit (MCP-290-00102-0N)

• SuperServer 6017R-N3RF4+/6017R-N3RFT+ Quick Reference Guide

Note: a complete list of safety warnings is provided on the Supermicro web site at

http://www.supermicro.com/about/policies/safety_information.cfm

1-1

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

1-2 Serverboard Features

At the heart of the SuperServer 6017R-N3RF4+/6017R-N3RFT+ lies the X9DRW­3LN4F+/X9DRW-3TF+, a dual processor serverboard based on the Intel® C606
chipset. Below are the main features of the serverboard. (See Figure 1-1 for a
block diagram of the chipset).

Processors

The X9DRW-3LN4F+/X9DRW-3TF+ supports single or dual Intel® E5-2600 Series
processors in LGA2011 sockets. Please refer to our web site for a complete listing
of supported processors (www.supermicro.com).

Memory

The X9DRW-3LN4F+/X9DRW-3TF+ has 24 memory sockets that can support up
to 768 GB of ECC registered DDR3-1333/1066/800 RDIMMs or up to 192 GB of
unbuffered DDR3-1333/1066/800 UDIMMs. Please refer to Chapter 5 for installing
memory.

Onboard SAS

A SAS controller is integrated into the chipset and provides eight SAS2 ports. The
hot-swap SAS drives are connected to a backplane that provides power, bus ter­mination and confi guration settings. RAID 0, 1 and 10 are supported.

Onboard Serial ATA

A SATA controller is integrated into the chipset to provide a six-port SATA sub­system. Two of the ports support SATA 3.0 and four support SATA 2.0 (see
Chapter 5 for details). RAID 0, 1, 5 and 10 are supported. The SATA drives are
hot-swappable units.

Rear I/O Ports

The color-coded I/O ports include one COM port, a VGA (monitor) port, two USB

2.0 ports, PS/2 mouse and keyboard ports, one dedicated IPMI LAN port and four
gigabit Ethernet ports. Two of the LAN ports on the 6017R-N3RFT+ (X9DRW-3TF+)
are 10 Gb Ethernet ports.

Graphics Controller

The X9DRW-3LN4F+/X9DRW-3TF+ features an integrated G200 (Renesas SH7757
BMC) graphics chip.

1-2

Chapter 1: Introduction

1-3 Server Chassis Features

The 6017R-N3RF4+/6017R-N3RFT+ is built upon the SC819TQ-R700WB chassis.
Details on the chassis and on servicing procedures can be found in Chapter 6.The
following is a general outline of the main features of the chassis.

System Power

The SC819TQ-R700WB features a redundant 700W power supply consisting of
two power modules. The system does not need to be shut down when replacing or
removing a single power supply module.

Hard Drives

The SC819TQ-R700WB chassis was designed to support four hot-swap SAS or
SATA hard drives.

PCI Expansion Slots

Two riser cards are included. The RSC-R1UW-2E16-O-P supports one standard
size PCI-E 3.0 x16 card and one standard size PCI-E 3.0 x8 card. The RSC-R1UW­E8R-O-P supports one low-profi le PCI-E 3.0 x8 add-on card. See our web site for
details (http://www.supermicro.com/products/nfo/UIO.cfm) and section 5-6 of this
manual for details.

Front Control Panel

The chassis' control panel provides you with system monitoring and control. LEDs
indicate system power, HDD activity, network activity (2), overheat/fan/power failure
and system information. A main power button and a UID button is also included.

Cooling System

The SC819TQ-R700WB has an innovative cooling design that features six sets of
4-cm counter-rotating fans located in the middle section of the chassis. Fan speed
may be determined by IPMI. The power supply module also includes a cooling fan.

1-3

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Figure 1-1. Intel C606 Chipset:

System Block Diagram

Note: This is a general block diagram. Please see Chapter 5 for details.

LEFT WIO

x16

x16

x16

CPU0/PE3

CPU1/PE2

RJ45

RJ45

RIGHT WIO

x16

RJ45 RJ45

Powerville /

Twinville
L3 / L4

CPU1/PE3CPU0/PE2

Powerville-2
L1 / L2

UL8

UL1

#1

#2

#3

#1

#2

#3

To WIO

Riser Card

E

DDR3 DIMM

C

DDR3 DIMM

To WIO

Riser Card

#1

#2

#3

#1

#2

#3

x16

x16

PE3 PE2 PE1 DMI

F

E5-2600 Series Processor

U7C1

DDR3 DIMM

U6H1

D

E5-2600 Series Processor

PE3 PE2 PE1 DMI

DDR3 DIMM

x16

x16

x4

CPU REAR

U7C1

Socket 01

PROCESSOR

P0

QPI

P1

CPU FRONT

U6H1

Socket 00

PROCESSOR

[7..4]

P1

P0

x4

DDR III

QPI

[3..0]

UM1

#3

H

B

#3

AT25321

SPI

DMI

PEG0

PEG1 [4:1]

PEG1_8

RENESAS

VGA BMC

#1

#2

G

DDR3 DIMM

#1

#2

DDR3 DIMM

U3G1

Intel C606

x1

A

LPC

USB

#2

#3

#3

#1

DDR3 DIMM

#1

#2

DDR3 DIMM

SATA
#1~#6

SAS

#1~#8

USB

TPM HDR

SATA

0,1

REAR

SAS

HDR 2X5

HDR 2X5

2,3

4,5

TYPE-A

6

1-4

VGA CONN

PHY1

RTL8211

LAN

SIO

W83527

1-4 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)

Chapter 1: Introduction

Web Site:

Europe

Address: Super Micro Computer B.V.

Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

Asia-Pacifi c

Address: Super Micro Computer, Inc.

www.supermicro.com

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

[e-mail] (Technical Support)

[e-mail] (Customer Support)

4F, No. 232-1, Liancheng Rd

Chung-Ho Dist., New Taipei City 235

Taiwan
Tel: [phone]
Fax: [phone]
Web Site:
Technical Support:
Email: [e-mail]
Tel: [phone]

www.supermicro.com.tw

1-5

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Notes

1-6

Chapter 2: Server Installation

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your 6017R-N3RF4+/6017R­N3RFT+ up and running. Following these steps in the order given should enable
you to have the system operational within a minimum amount of time. This quick
setup assumes that your system has come to you with the processors and memory
pre-installed. If your system is not already fully integrated with a serverboard, pro­cessors, system memory etc., please turn to the chapter or section noted in each
step for details on installing specifi c components.

2-2 Unpacking the System

You should inspect the box the 6017R-N3RF4+/6017R-N3RFT+ was shipped in and
note if it was damaged in any way. If the server itself shows damage you should
fi le a damage claim with the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the 6017R­N3RF4+/6017R-N3RFT+. It should be situated in a clean, dust-free area that is
well ventilated. Avoid areas where heat, electrical noise and electromagnetic fi elds
are generated. You will also need it placed near a grounded power outlet. Be sure
to read the Rack and Server Precautions in the next section.

2-3 Preparing for Setup

The box the 6017R-N3RF4+/6017R-N3RFT+ was shipped in should include two
sets of rail assemblies, two rail mounting brackets and the mounting screws you
will need to install the system into the rack. Follow the steps in the order given to
complete the installation process in a minimum amount of time. Please read this
section in its entirety before you begin the installation procedure outlined in the
sections that follow.

Choosing a Setup Location

• Leave enough clearance in front of the rack to enable you to open the front door

completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for suffi cient airfl ow and ease in servicing.This product is for

2-1

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

installation only in a Restricted Access Location (dedicated equipment rooms,
service closets and the like).

• This product is not suitable for use with visual display work place devices

acccording to §2 of the the German Ordinance for Work with Visual Display Units.

2-4 Warnings and Precautions!

Rack Precautions

• Ensure that the leveling jacks on the bottom of the rack are fully extended to

the fl oor with the full weight of the rack resting on them.

• In single rack installation, stabilizers should be attached to the rack. In multiple

rack installations, the racks should be coupled together.

• Always make sure the rack is stable before extending a component from the

rack.

• You should extend only one component at a time - extending two or more si-

multaneously may cause the rack to become unstable.

Server Precautions

• Review the electrical and general safety precautions in Chapter 4.

• Determine the placement of each component in the rack before you install the

rails.

• Install the heaviest server components on the bottom of the rack fi rst, and then

work up.

• Use a regulating uninterruptible power supply (UPS) to protect the server from

power surges, voltage spikes and to keep your system operating in case of a
power failure.

• Allow the hot plug SAS/SATA drives and power supply modules to cool before

touching them.

• Always keep the rack's front door and all panels and components on the servers

closed when not servicing to maintain proper cooling.

2-2

Chapter 2: Server Installation

Rack Mounting Considerations

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating tempera­ture of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient tempera­ture (Tmra).

Reduced Airfl ow

Equipment should be mounted into a rack so that the amount of airfl ow required
for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.

Circuit Overloading

Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connec­tions other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).

2-3

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

2-5 Installing the System into a Rack

This section provides information on installing the 6017R-N3RF4+/6017R-N3RFT+
into a rack unit with the rack rails provided. If the system has already been mounted
into a rack, you can skip ahead to Sections 2-5 and 2-6. There are a variety of rack
units on the market, which may mean the assembly procedure will differ slightly.
You should also refer to the installation instructions that came with the rack unit

you are using.

Identifying the Sections of the Rack Rails

You should have received two rack rail assemblies in the rack mounting kit. Each
assembly consists of two sections: an inner fi xed chassis rail that secures directly
to the server chassis and an outer fi xed rack rail that secures directly to the rack
itself (see Figure 2-1). Two pairs of short brackets to be used on the front side of
the outer rails are also included.

Installing the Inner Rails

Both the left and right side inner rails have been pre-attached to the chassis. Pro­ceed to the next step.

Figure 2-1. Identifying the Sections of the Rack Rails

(left side rail shown)

Inner Rail Outer RailLocking Tab

Warning: do not pick up the server with the front handles. They are de-

signed to pull the system from a rack only.

2-4

Chapter 2: Server Installation

Installing the Outer Rails

Installing the Outer Rails to the Rack

1. Measure the distance from the front rail to the rear rail of the rack.

2. Attach a short bracket to the front side of the right outer rail and a long
bracket to the rear side of the right outer rail.

3. Adjust both the short and long brackets to the proper distance so that the rail
can fi t snugly into the rack.

4. Secure the short bracket to the front side of the outer rail with two M4 screws
and the long bracket to the rear side of the outer rail with three M4 screws.

5. Repeat these steps for the left outer rail.

Locking Tabs

Both chassis rails have a locking tab, which serves two functions. The fi rst is to
lock the server into place when installed and pushed fully into the rack, which is
its normal position. Secondly, these tabs also lock the server in place when fully
extended from the rack. This prevents the server from coming completely out of the
rack when you pull it out for servicing.

Figure 2-2. Installing the Rack Rails

2-5

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Installing the Server into the Rack

Installing the Chassis into a Rack (Figure 2-3)

1. Confi rm that chassis includes the inner rails and rail extensions . Also, confi rm
that the outer rails are installed on the rack.

2. Line chassis rails with the front of the rack rails.

3. Slide the chassis rails into the rack rails, keeping the pressure even on both
sides (you may have to depress the locking tabs when inserting). When the
server has been pushed completely into the rack, you should hear the locking
tabs "click".

4. (Optional) Insert and tightening the thumbscrews that hold the front of the
server to the rack.

Installing the Server into a Telco Rack

To install the 6017R-N3RF4+/6017R-N3RFT+ into a Telco type rack, use two L­shaped brackets on either side of the chassis (four total). First, determine how far
follow the server will extend out the front of the rack. Larger chassis should be
positioned to balance the weight between front and back. If a bezel is included on
your server, remove it. Then attach the two front brackets to each side of the chas­sis, then the two rear brackets positioned with just enough space to accommodate
the width of the telco rack. Finish by sliding the chassis into the rack and tightening
the brackets to the rack.

Stability hazard. The rack stabilizing mechanism must be in place, or the
rack must be bolted to the fl oor before you slide the unit out for servicing.
Failure to stabilize the rack can cause the rack to tip over.

2-6

Chapter 2: Server Installation

Figure 2-3. Installing the Server into a Rack

Warning! To prevent bodily injury when mounting or servicing this unit in a

rack, you must take special precautions to ensure that the system remains
stable. The following guidelines are provided to ensure your safety:

• This unit should be mounted at the bottom of the rack if it is the only unit in

the rack.

• When mounting this unit in a partially fi lled rack, load the rack from the bottom

to the top with the heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before

mounting or servicing the unit in the rack.

2-7

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Notes

2-8

Chapter 3: System Interface

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the control panel as well as others on the hard drive
carriers to keep you constantly informed of the overall status of the system as well
as the activity and health of specifi c components. There are also three buttons on
the chassis control panel. This chapter explains the meanings of all LED indicators

and the appropriate response you may need to take.

3-2 Control Panel Buttons

There are three push-buttons located on the front of the chassis. These are (in order
from left to right) a UID button, a reset button and a power on/off button.

UID

Depressing the UID (unit identifi er) button illuminates an LED on both the front and
rear of the chassis for easy system location in large stack confi gurations. The LED
will remain on until the button is pushed a second time. Another UID button on the
rear of the chassis serves the same function.

Reset

The reset button reboots the system.

Power

The main power switch is used to apply or remove power from the power supply
to the server system. Turning off system power with this button removes the main
power but keeps standby power supplied to the system.

3-1

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

3-3 Control Panel LEDs

The control panel located on the front of the SC819TQ chassis has fi ve LEDs. These
LEDs provide you with critical information related to different parts of the system.
This section explains what each LED indicates when illuminated and any corrective
action you may need to take.

Information LED

This LED will be solid blue when the UID function has been activated. When this
LED fl ashes red, it indicates a fan failure. When red continuously it indicates an
overheat condition, which may be caused by cables obstructing the airfl ow in the
system or the ambient room temperature being too warm. Check the routing of
the cables and make sure all fans are present and operating normally. You should
also check to make sure that the chassis covers are installed. Finally, verify that
the heatsinks are installed properly (see Chapter 5). This LED will remain fl ashing
or on as long as the indicated condition exists.

2

NIC2

Indicates network activity on LAN2 when fl ashing .

1

NIC1

Indicates network activity on LAN1 when fl ashing.

HDD

Indicates IDE channel activity. On the 6017R-N3RF4+/6017R-N3RFT+ this light
indicates HDD and/or DVD-ROM drive activity when fl ashing.

3-2

Chapter 3: System Interface

Power

Indicates power is being supplied to the system's power supply units. This LED
should normally be illuminated when the system is operating.

3-4 Drive Carrier LEDs

 Green: Each drive carrier has a green LED. When illuminated, this green
LED indicates drive activity. A connection to the SATA backplane enables this
LED to blink on and off when that particular drive is being accessed. Please refer
to Chapter 6 for instructions on replacing failed SATA drives.

 Red: The red LED to indicate a SATA drive failure. If one of the drives fail, you
should be notifi ed by your system management software. Please refer to Chapter
6 for instructions on replacing failed SATA drives.

3-3

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Notes

3-4

Chapter 4: Warning Statements for AC Systems

Chapter 4

Standardized Warning Statements for AC Systems

4-1 About Standardized Warning Statements

The following statements are industry standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions
or experience difficulty, contact Supermicro's Technical Support department
for assistance. Only certifi ed technicians should attempt to install or confi gure
components.

Read this appendix in its entirety before installing or confi guring components in the
Supermicro chassis.

These warnings may also be found on our web site at http://www.supermicro.com/
about/policies/safety_information.cfm.

Warning Defi nition

Warning!

This warning symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.

警告の定義

この警告サインは危険を意味します。

人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、

電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。

此警告符号代表危险。

您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前，必须充分
意识到触电的危险，并熟练掌握防止事故发生的标准工作程序。请根据每项警告结
尾的声明号码找到此设备的安全性警告说明的翻译文本。

此警告符號代表危險。

您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前，請注意觸
電的危險，並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號
碼找到相關的翻譯說明內容。

4-1

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

ןונקת תורהצהאהרהז

Warnung

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befi nden sich in einer Situation, die zu
Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den
Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung
vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen
Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes
de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y
familiarícese con los procedimientos estándar de prevención de accidentes. Al
fi nal de cada advertencia encontrará el número que le ayudará a encontrar el texto
traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES.

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une
situation pouvant entraîner des blessures ou des dommages corporels. Avant
de travailler sur un équipement, soyez conscient des dangers liés aux circuits
électriques et familiarisez-vous avec les procédures couramment utilisées pour
éviter les accidents. Pour prendre connaissance des traductions des avertissements
fi gurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fi n de chaque avertissement.

CONSERVEZ CES INFORMATIONS.

ןה תואבה תורהצהא ינפמ שמתשמה תא ריהזהל תנמ לע ,היישעתה ינקת יפ לע תורהז הלבח

ה וא תולאש שיו הדימב .תירשפא תיזיפי ,יהשלכ היעבב תולקתרוציל שי הכימת תקלחמ םע רשק

רידגהל וא ןיקתהל םיאשר דבלב םיכמסומ םיאנכט .ורקימרפוס לש תינכט תאה .םיביכר

תרדגה וא תנקתה ינפל ואולמב חפסנה תא

אורקל שי .ורקימרפוס יזראמב םיביכרה

4-2

Warning Statements for AC Systems

. ﻲﻓ ﻚﻧﺍ ﻥﺃ ﻦﻜﻤﻳ ﺔﻟﺎﺣ ﻲﻓ ﺐﺒﺴﺘﺗ ﺔﺑﺎﺻﺍ ﺔﻳﺪﺴﺟ ﺰﻣﺮﻟﺍ ﺍﺬﻫ ﻲﻨﻌﻳ ﺮﻄﺧ !ﺮﻳﺬﺤﺗ

ﻥﺃ ﻞﺒﻗ ﻱﺃ ﻰﻠﻋ ﻞﻤﻌﺗ ﺕﺍﺪﻌﻣ،ﻛﻢﻠﻋ ﻰﻠﻋ ﻦ ﻦﻋ ﺔﻤﺟﺎﻨﻟﺍ ﺮﻁﺎﺨﻤﻟﺎﺑ ﺮﺋﺍﻭﺪﻟﺍ

ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ

ﻛﻭﺔﻳﺍﺭﺩ ﻰﻠﻋ ﻦ ﺭﺎﻤﻤﻟﺎﺑﺕﺎﺳ ﺔﻴﺋﺎﻗﻮﻟﺍ ﻟ ﻊﻨﻤﻉﻮﻗﻭ ﻱﺃﺙﺩﺍﻮﺣ

ﻢﻗﺭ ﻡﺪﺨﺘﺳﺍ ﻥﺎﻴﺒﻟﺍ ﺹﻮﺼﻨﻤﻟﺍ ﺔﻳﺎﻬﻧ ﻲﻓ ﺮﻳﺬﺤﺗ ﻞﻛ ﺭﻮﺜﻌﻠﻟ ﺎﻬﺘﻤﺟﺮﺗ

안전을 위한 주의사항

경고!

이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수
있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와
관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준
작업절차를 준수해 주시기 바랍니다.

해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를
참조하십시오

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die
lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,
dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's
en dient u op de hoogte te zijn van de standaard procedures om ongelukken te
voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te
herleiden naar de desbetreffende locatie.

BEWAAR DEZE INSTRUCTIES

4-3

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Installation Instructions

Warning!

Read the installation instructions before connecting the system to the power source.

設置手順書

システムを電源に接続する前に、設置手順書をお読み下さい。

警告
将此系统连接电源前,请先阅读安装说明。

警告
將系統與電源連接前，請先閱讀安裝說明。

Warnung

Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen
lesen.

¡Advertencia!

Lea las instrucciones de instalación antes de conectar el sistema a la red de
alimentación.

Attention

Avant de brancher le système sur la source d'alimentation, consulter les directives
d'installation.

אורקל שי רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תאחתמ.

ﻟﺍ ﺕﺍﺩﺎﺷﺭﺇ ﺮﻗﺍﺐﻴﻛﺮﺘ ﻞﻴﺻﻮﺗ ﻞﺒﻗ ﻰﻟﺇ ﻡﺎﻈﻨﻟﺍ ﺔﻗﺎﻄﻠﻟ ﺭﺪﺼﻣ

시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오.

Waarschuwing

Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron
aansluit.

4-4

Chapter 4: Warning Statements for AC Systems

Circuit Breaker

Warning!

This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.

サーキット・ブレーカー

この製 品 は、短絡（過電流）保護装置がある建物での設置を前提としています。

保護装置の定格が250V、20Aを超えないことを確認下さい。

警告
此产品的短路(过载电流)保护由建筑物的供电系统提供,确保短路保护设备的额定电
流不大于250V,20A。

警告
此產品的短路(過載電流)保護由建築物的供電系統提供,確保短路保護設備的額定電
流不大於250V,20A。

Warnung

Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss­bzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der
Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt.

¡Advertencia!

Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes)
del edifi cio. Asegúrese de que el dispositivo de protección no sea superior a: 250
V, 20 A.

Attention

Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit
dépend de l'installation électrique du local. Vérifi ez que le courant nominal du
dispositif de protection n'est pas supérieur à :250 V, 20 A.

ﺞﺘﻨﻤﻟﺍ ﺍﺬﻫ ﻰﻠﻋ ﺪﻤﺘﻌﻳ ﺕﺍﺪﻌﻣ ﺔﻳﺎﻤﺤﻟﺍ ﺓﺮﻴﺼﻘﻟﺍﺮﺋﺍﻭﺪﻟﺍ ﻦﻣ ﺎﻬﺘﻴﺒﺜﺗ ﻢﺗ ﻲﺘﻟﺍ ﻲﻓ

לע ךמתסמ הז רצומנגהה תעינמל םינבמב תנקתומה יכ אדוול שי .ילמשח רצק

רצקה ינפמ ןגמה רישכמה ילמשחהמ רתוי אל אוה-250 V, 20 A

ﻰﻨﺒﻤﻟﺍ

20A, 250V : ﻦﻣ ﺪﻛﺄﺗ ﻥﺃ ﻢﻴﻴﻘﺗ ﺯﺎﻬﺠﻟﺍ ﻟﺍﻲﺋﺎﻗﻮ ﺲﻴﻟ ﻦﻣ ﺮﺜﻛﺃ

4-5

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

경고!

이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에
의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지
않도록 해야 합니다.

Waarschuwing

Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van
uw electrische installatie. Controleer of het beveiligde aparaat niet groter
gedimensioneerd is dan 220V, 20A.

Power Disconnection Warning

Warning!

The system must be disconnected from all sources of power and the power cord
removed from the power supply module(s) before accessing the chassis interior to
install or remove system components.

電源切断の警告

システムコンポーネントの取り付けまたは取り外しのために、シャーシー内部にアクセス

するには、

システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り

外す必要があります。

警告

在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。

警告

在您打開機殼安裝或移除內部元件前，必須將系統完全斷電，並移除電源線。

Warnung

Das System muss von allen Quellen der Energie und vom Netzanschlusskabel
getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es
auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder
zu entfernen.

4-6

Chapter 4: Warning Statements for AC Systems

ילמשח קותינ ינפמ הרהזא

!הרהזא

¡Advertencia!

El sistema debe ser disconnected de todas las fuentes de energía y del cable
eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso
el interior del chasis para instalar o para quitar componentes de sistema.

Attention

Le système doit être débranché de toutes les sources de puissance ainsi que de
son cordon d'alimentation secteur avant d'accéder à l'intérieur du chassis pour
installer ou enlever des composants de systéme.

למשחה תורוקמ לכמ תכרעמה תא קתנל שי ריסהל שיו קפסהמ ילמשחה לבכ תא

נקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפלת רסה ואת .םיביכר

ﻞﺼﻓ ﺐﺠﻳ ﻡﺎﻈﻨﻟﺍ ﻊﻴﻤﺟ ﻦﻣﺭﺩﺎﺼﻣ ﺔﻗﺎﻄﻟﺍ ﺔﻟﺍﺯﺇﻭ ءﺎﺑﺮﻬﻜﻟﺍ ﻚﻠﺳ ﻦﻣ ﺓﺪﺣﻭ ﺩﺍﺪﻣﺍ

ﺔﻗﺎﻄﻟﺍ ﻞﺒﻗ

ﺯﺎﻬﺠﻟﺍ

경고!

시스템에 부품들을 장착하거나 제거하기 위해서는 섀시 내부에 접근하기 전에
반드시 전원 공급장치로부터 연결되어있는 모든 전원과 전기코드를 분리해주어야
합니다.

Waarschuwing

Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren
of verwijderen van systeem onderdelen, dient u alle spanningsbronnen en alle
stroomkabels aangesloten op de voeding(en) van de behuizing te verwijderen

ﻰﻟﺇ ﻝﻮﺻﻮﻟﺍ ﺔﻴﻠﺧﺍﺪﻟﺍ ﻖﻁﺎﻨﻤﻟﺍ ﻟﻞﻜﻴﻬﻠ ﺔﻟﺍﺯﺇ ﻭﺃ ﺖﻴﺒﺜﺘﻟ ﺕﺎﻧﻮﻜﻣ

4-7

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Equipment Installation

Warning!

Only trained and qualifi ed personnel should be allowed to install, replace, or service
this equipment.

機器の設置

トレーニングを受け認定された人だけがこの装置の設置、交換、またはサービスを許可

されています。

警告
只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。

警告
只有經過受訓且具資格人員才可安裝、更換與維修此設備。

Warnung

Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,
qualifi ziertem Personal gestattet werden.

¡Advertencia!

Solamente el personal califi cado debe instalar, reemplazar o utilizar este equipo.

Attention

Il est vivement recommandé de confier l'installation, le remplacement et la
maintenance de ces équipements à des personnels qualifi és et expérimentés.

!הרהזא

שר דבלב ךמסומ תווצתא ףילחהל ,ןיקתהל יא .דויצה רובע תוריש תתל וא דויצה

ﻦﻴﺑﺭﺪﻤﻟﺍﻭ ﻭ ﺐﻴﻛﺮﺘﻟﻝﺍﺪﺒﺘﺳﺍ ﻭﺃ ﺔﻣﺪﺧ ﺯﺎﻬﺠﻟﺍ ﺍﺬﻫ ﺢﻤﺴﻳ ﻥﺃ ﺐﺠﻳ ﻂﻘﻓ ﻦﻴﻠﻫﺆﻤﻟﺍ ﻦﻴﻔﻅﻮﻤﻠﻟ

경고!

훈련을 받고 공인된 기술자만이 이 장비의 설치, 교체 또는 서비스를 수행할 수
있습니다.

4-8

Chapter 4: Warning Statements for AC Systems

Waarschuwing

Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door
geschoold en gekwalifi ceerd personeel.

Restricted Area

Warning!

This unit is intended for installation in restricted access areas. A restricted access
area can be accessed only through the use of a special tool, lock and key, or other
means of security. (This warning does not apply to workstations).

アクセス制限区域
このユ ニットは、アクセス制限区域に設置されることを想定しています。
アクセス制限区域は、特別なツール、鍵と錠 前、その他のセキュリティの手段を用いての

み出入りが可能です。

警告
此部件应安装在限制进出的场所，限制进出的场所指只能通过使用特殊工具、锁和
钥匙或其它安全手段进出的场所。

警告
此裝置僅限安裝於進出管制區域，進出管制區域係指僅能以特殊工具、鎖頭及鑰匙
或其他安全方式才能進入的區域。

Warnung

Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen.
Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und
Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich.

¡Advertencia!

Esta unidad ha sido diseñada para instalación en áreas de acceso restringido.
Sólo puede obtenerse acceso a una de estas áreas mediante la utilización de una
herramienta especial, cerradura con llave u otro medio de seguridad.

Attention

Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une
zone d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme
de verrouillage et une clé, ou tout autre moyen de sécurité.

4-9

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

תלבגומ השיג םע רוזא

!הרהזא

תרזעב תנתינ השיגה .השיג תלבגה םהב שיש םירוזאב הדיחיה תא ןיקתהל שי

.('דכו לוענמ ,חתפמ) דבלב החטבא ילכ

. ﺺﻴﺼﺨﺗ ﺓﺪﺣﻮﻟﺍ ﻩﺬﻫ ﻲﻓ ﺎﻬﺒﻴﻛﺮﺘﻟ ﻖﻁﺎﻨﻣ ﺓﺭﻮﻈﺤﻣ ﻢﺗ

ﺻﻮﻟﺍ ﻦﻜﻤﻳﻰﻟﺇ ﻝﻮ ﺔﻘﻄﻨﻣ ﺓﺭﻮﻈﺤﻣ ﻂﻘﻓ ﻡﺍﺪﺨﺘﺳﺍ ﻝﻼﺧ ﻦﻣ ،ﺔﺻﺎﺧ ﺓﺍﺩﺃ

ﻭﺃ ﻱﺃ ﻼﻟ ﻯﺮﺧﺃ ﺔﻠﻴﺳﻭﻥﺎﻣﻷ ﺡﺎﺘﻔﻣﻭ ﻞﻔﻗ

경고!

이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다. 특수도구, 잠금 장치 및
키, 또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다.

Waarschuwing

Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang.
Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te
maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.

Battery Handling

Warning!

There is the danger of explosion if the battery is replaced incorrectly. Replace the
battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメー
カーが推奨する型、または同 等のものを使 用下さい。使用済電池は製造元の指示に従
って処 分して 下さい 。

警告

电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更

换原有电池。请按制造商的说明处理废旧电池。

警告

電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有

電池。請按照製造商的說明指示處理廢棄舊電池。

4-10

Chapter 4: Warning Statements for AC Systems

!הרהזא

Warnung

Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die
Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.

Attention

Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer
que par une pile de type semblable ou équivalent, recommandée par le fabricant.
Jeter les piles usagées conformément aux instructions du fabricant.

¡Advertencia!

Existe peligro de explosión si la batería se reemplaza de manera incorrecta.
Reemplazar la batería exclusivamente con el mismo tipo o el equivalente
recomendado por el fabricante. Desechar las baterías gastadas según las
instrucciones del fabricante.

תנכס תמייקץוציפ .הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי

גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ.

תוללוסה קוליס תושמושמה עצבל שי .ןרציה תוארוה יפל

ﺮﻄﺧ ﻙﺎﻨﻫ ﻦﻣ ﻝﺍﺪﺒﺘﺳﺍ ﺔﻟﺎﺣ ﻲﻓ ﺭﺎﺠﻔﻧﺍ ﺔﻳﺭﺎﻄﺒﻟﺍ ﺔﺤﻴﺤﺻ ﺮﻴﻏ ﺔﻘﻳﺮﻄﺑ ﻚﻴﻠﻌﻓ

ﺔﻳﺭﺎﻄﺒﻟﺍ ﻝﺍﺪﺒﺘﺳﺍ

ﻂﻘﻓ ﻉﻮﻨﻟﺍ ﺲﻔﻨﺑ ﺎﻬﻟﺩﺎﻌﻳ ﺎﻣ ﻭﺃ ﺎﻤﻛﺖﺻﻭﺃ ﺔﻌﻨﺼﻤﻟﺍ ﺔﻛﺮﺸﻟﺍ ﻪﺑ

ﺕﺎﻳﺭﺎﻄﺒﻟﺍ ﻦﻣ ﺺﻠﺨﺗ ﻟ ﺎﻘﻓﻭ ﺔﻠﻤﻌﺘﺴﻤﻟﺍﺔﻌﻧﺎﺼﻟﺍ ﺔﻛﺮﺸﻟﺍ ﺕﺎﻤﻴﻠﻌﺘ

경고!

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와
동일하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다.
제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.

Waarschuwing

Er is ontploffi ngsgevaar indien de batterij verkeerd vervangen wordt. Vervang de
batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen
wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd
te worden.

4-11

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

דחא קפסמ רתוי םייק םא

!הרהזא

Redundant Power Supplies

Warning!

This unit might have more than one power supply connection. All connections must

be removed to de-energize the unit.

冗長電源装置
このユニットは複数の電源装置が接続されている場合があります。

ユニットの電源を切るためには、すべての接続を取り外さなければなりません。

警告

此部件连接的电源可能不止一个，必须将所有电源断开才能停止给该部件供电。

警告

此裝置連接的電源可能不只一個，必須切斷所有電源才能停止對該裝置的供電。

Warnung

Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass

der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.

¡Advertencia!

Puede que esta unidad tenga más de una conexión para fuentes de alimentación.

Para cortar por completo el suministro de energía, deben desconectarse todas las

conexiones.

Attention

Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute

tension et tout courant électrique de l'unité, toutes les connexions d'alimentation

doivent être débranchées.

.קפס לש דחא רוביחמ רתוי שי הדחיל תא ריסהל שיןקורל תנמ לע םירוביחה לכ

חיה תאי.הד

4-12

Chapter 4: Warning Statements for AC Systems

. ﺪﻗ ﺍﺬﻬﻟ ﻥﻮﻜﻳ ﻟﺍﺯﺎﻬﺠ ﺕﻻﺎﺼﺗﺍ ﺓﺪﻋ ﺕﺍﺪﺣﻮﺑ ﺔﻗﺎﻄﻟﺍ ﺩﺍﺪﻣﺍ

ﺔﻟﺍﺯﺇ ﺐﺠﻳ ﺕﻻﺎﺼﺗﻻﺍ ﺔﻓﺎﻛ ﻝﺰﻌﻟ ﻟﺍﺓﺪﺣﻮ ﻦﻋ ءﺎﺑﺮﻬﻜﻟﺍ

경고!

이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에
전원을 차단하기 위해서는 모든 연결 단자를 제거해야만 합니다.

Waarschuwing

Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle
aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken.

Backplane Voltage

Warning!

Hazardous voltage or energy is present on the backplane when the system is
operating. Use caution when servicing.

バックプレーンの電圧
システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。

修理する際には注意ください。

警告
当系统正在进行时，背板上有很危险的电压或能量，进行维修时务必小心。

警告
當系統正在進行時，背板上有危險的電壓或能量，進行維修時務必小心。

Warnung

Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche
Spannungen oder Energien auf. Vorsicht bei der Wartung.

¡Advertencia!

Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso.
Tenga cuidado cuando lo revise.

Attention

Lorsque le système est en fonctionnement, des tensions électriques circulent sur
le fond de panier. Prendre des précautions lors de la maintenance.

4-13

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

ירוחאה לנפב חתמ

ךלהמב רהזיהל שי .תכרעמה לועפת ןמזב ירוחאה לנפב חתמ תנכס תמייק

זא!הרה

.הדובעה

ﻙﺎﻨﻫ ﺮﻄﺧ ﻦﻣ ﻲﺋﺎﺑﺮﻬﻜﻟﺍ ﺭﺎﻴﺘﻟﺍ ﻰﻠﻋ ﺓﺩﻮﺟﻮﻤﻟﺍ ﺔﻗﺎﻄﻟﺍﻭﺃ ﺔﺣﻮﻠﻟﺍ

ﻥﻮﻜﻳ ﺎﻣﺪﻨﻋﻡﺎﻈﻨﻟﺍ ﻞﻤﻌﻳ ﺪﻨﻋ ﺍﺭﺬﺣ ﻦﻛ ﺔﻣﺪﺧ ﺯﺎﻬﺠﻟﺍ ﺍﺬﻫ

경고!

시스템이 동작 중일 때 후면판 (Backplane)에는 위험한 전압이나 에너지가 발생
합니다. 서비스 작업 시 주의하십시오.

Waarschuwing

Een gevaarlijke spanning of energie is aanwezig op de backplane wanneer het
systeem in gebruik is. Voorzichtigheid is geboden tijdens het onderhoud.

Comply with Local and National Electrical Codes

Warning!

Installation of the equipment must comply with local and national electrical codes.

地方および国の電気規格に準拠

機器の取り付けはその地方および国の電気規格に準拠する必要があります。

警告

设备安装必须符合本地与本国电气法规。

警告

設備安裝必須符合本地與本國電氣法規。

Warnung

Die Installation der Geräte muss den Sicherheitsstandards entsprechen.

¡Advertencia!

La instalacion del equipo debe cumplir con las normas de electricidad locales y

nacionales.

4-14

Chapter 4: Warning Statements for AC Systems

יצראה למשחה יקוח םואית

Attention

L'équipement doit être installé conformément aux normes électriques nationales
et locales.

!הרהזא

תנקתה םייצראהו םיימוקמה למשחה יקוחל תמאות תויהל תבייח דויצה.

ﺕﺍﺪﻌﻤﻟﺍ ﺐﻴﻛﺮﺗ ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﻠﻟ ﻞﺜﺘﻤﻳ ﻥﺃ ﺐﺠﻳ ﻦﻴﻧﺍﻮﻘﺔﻴﻨﻁﻮﻟﺍﻭ ﺔﻴﻠﺤﻤﻟﺍ ﺔﻘﻠﻌﺘﻤﻟﺍ

ءﺎﺑﺮﻬﻜﻟﺎﺑ

경고!

현 지역 및 국가의 전기 규정에 따라 장비를 설치해야 합니다.

Waarschuwing

Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale
elektriciteitsvoorschriften.

Product Disposal

Warning!

Ultimate disposal of this product should be handled according to all national laws
and regulations.

製品の廃棄

この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が
あります。

警告
本产品的废弃处理应根据所有国家的法律和规章进行。

警告
本產品的廢棄處理應根據所有國家的法律和規章進行。

Warnung

Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen
des Landes erfolgen.

4-15

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

רצומה קוליס

¡Advertencia!

Al deshacerse por completo de este producto debe seguir todas las leyes y

reglamentos nacionales.

Attention

La mise au rebut ou le recyclage de ce produit sont généralement soumis à des

lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de

l'organisme compétent.

!הרהזא

ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס.הנידמה יקוח

ﻲﺋﺎﻬﻨﻟﺍ ﺺﻠﺨﺘﻟﺍ ﻦﻣ ﺞﺘﻨﻤﻟﺍ ﺍﺬﻫ ﻪﻌﻣ ﻞﻣﺎﻌﺘﻟﺍ ﻲﻐﺒﻨﻳ ﻟ ﺎﻘﻓﻭ ﻊﻴﻤﺠﺔﻴﻨﻁﻮﻟﺍ ﺢﺋﺍﻮﻠﻟﺍﻭ ﻦﻴﻧﺍﻮﻘﻟﺍ ﺪﻨﻋ

경고!

이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.

Waarschuwing

De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming
met alle nationale wetten en reglementen.

Hot Swap Fan Warning

Warning!

The fans might still be turning when you remove the fan assembly from the chassis.
Keep fi ngers, screwdrivers, and other objects away from the openings in the fan
assembly's housing.

ファン・ホットスワップの警告

シャーシから冷却ファン装置を取り外した際、ファンがまだ回転している可能性がありま

す。ファンの開口部に、指、ドライバー、およびその他のものを近づけないで下さい。

警告

当您从机架移除风扇装置，风扇可能仍在转动。小心不要将手指、螺丝起子和其他

物品太靠近风扇

4-16

Chapter 4: Warning Statements for AC Systems

警告
當您從機架移除風扇裝置，風扇可能仍在轉動。小心不要將手指、螺絲起子和其他
物品太靠近風扇。

Warnung

Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis
genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände
von den Öffnungen des Lüftergehäuses entfernt.

¡Advertencia!

Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador
del chasis. Mandtenga los dedos, los destornilladores y todos los objetos lejos de
las aberturas del ventilador

Attention

Il est possible que les ventilateurs soient toujours en rotation lorsque vous retirerez
le bloc ventilateur du châssis. Prenez garde à ce que doigts, tournevis et autres
objets soient éloignés du logement du bloc ventilateur.

!הרהזא

יקלח תא םיריסמ רשאכ שי .םידבוע ןיידע םיררוואמהו ןכתי ,זראמהמ ררוואמה

קיחרהללררוואמה ךותב םיחתפהמ םינוש הדובע ילכו תועבצאה תא חוטב קחרמ

ﻦﻜﻤﻤﻟﺍ ﻦﻣ ﺡﻭﺍﺮﻤﻟﺍ ﻥﺃ ﻝﺍﺰﺗ ﻻ ﺔﻟﺍﺯﺇ ﺪﻨﻋﺭﻭﺪﺗ ﺔﻠﺘﻛ ﺔﺣﻭﺮﻤﻟﺍ ﻞﻜﻴﻬﻟﺍ ﻦﻣ ﺐﺠﻳ ءﺎﻘﺑﺇ

ﻊﺑﺎﺻﻷﺍ ﻭﻲﻏﺍﺮﺒﻟﺍ ﺕﺎﻜﻔﻣ

. ءﺎﻴﺷﻷﺍ ﻦﻣ ﺎﻫﺮﻴﻏﻭ ﺍﺪﻴﻌﺑ ﻦﻋ ﺕﺎﺤﺘﻔﻟﺍ ﻲﻓ ﺔﻠﺘﻛ ﺔﺣﻭﺮﻤﻟﺍ

경고!

섀시로부터 팬 조립품을 제거할 때 팬은 여전히 회전하고 있을 수 있습니다. 팬
조림품 외관의 열려있는 부분들로부터 손가락 및 스크류드라이버, 다른 물체들이
가까이 하지 않도록 배치해 주십시오.

Waarschuwing

Het is mogelijk dat de ventilator nog draait tijdens het verwijderen van het
ventilatorsamenstel uit het chassis. Houd uw vingers, schroevendraaiers
en eventuele andere voorwerpen uit de buurt van de openingen in de
ventilatorbehuizing.

4-17

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Power Cable and AC Adapter

Warning!

When installing the product, use the provided or designated connection cables,

power cables and AC adaptors. Using any other cables and adaptors could cause

a malfunction or a fi re. Electrical Appliance and Material Safety Law prohibits the

use of UL or CSA -certifi ed cables (that have UL/CSA shown on the code) for any

other electrical devices than products designated by Supermicro only.

電源コードとACアダプター

製品を設置する場合、提供または指定された接続ケーブル、電源コードとACアダプター
を使用下さい。他のケーブルやアダプタを使用すると故障や火災の原因になることがあ

ります。電気用品安全法は、ULまたはCSA認定のケーブル(UL/CSEマークがコードに表

記)をSupermicroが指定する製品以外に使用することを禁止しています。

警告
安装此产品时,请使用本身提供的或指定的连接线,电源线和电源适配器.使用其它线
材或适配器可能会引起故障或火灾。除了Supermicro所指定的产品,电气用品和材
料安全法律规定禁止使用未经UL或CSA认证的线材。(线材上会显示UL/CSA符号)。

警告
安裝此產品時,請使用本身提供的或指定的連接線,電源線和電源適配器.使用其它線
材或適配器可能會引起故障或火災。除了Supermicro所指定的產品,電氣用品和材
料安全法律規定禁止使用未經UL或CSA認證的線材。(線材上會顯示UL/CSA符號)。

Warnung

Bei der Installation des Produkts, die zur Verfügung gestellten oder benannt
Anschlusskabel, Stromkabel und Netzteile. Verwendung anderer Kabel und Adapter
kann zu einer Fehlfunktion oder ein Brand entstehen. Elektrische Geräte und
Material Safety Law verbietet die Verwendung von UL-oder CSA-zertifi zierte Kabel,
UL oder CSA auf der Code für alle anderen elektrischen Geräte als Produkte von
Supermicro nur bezeichnet gezeigt haben.

¡Advertencia!

Al instalar el producto, utilice los cables de conexión previstos o designados, los
cables y adaptadores de CA. La utilización de otros cables y adaptadores podría
ocasionar un mal funcionamiento o un incendio. Aparatos Eléctricos y la Ley de
Seguridad del Material prohíbe el uso de UL o CSA cables certifi cados que tienen
UL o CSA se muestra en el código de otros dispositivos eléctricos que los productos
designados por Supermicro solamente.

4-18

Chapter 4: Warning Statements for AC Systems

אתמו םיילמשחמ י

Attention

Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné.
L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement
ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit
l'utilisation de UL ou CSA câbles certifi és qui ont UL ou CSA indiqué sur le code
pour tous les autres appareils électriques que les produits désignés par Supermicro
seulement.

AC

!הרהזא

AC רשא

םימאתמו םיקפס ,םילבכב שמתשהל שי ,רצומה תא םיניקתמ רשאכ

וא הלקתל םורגל לוכי רחא םאתמ וא לבכ לכב שומיש .ךכ םשל וקפוסו ודעונ

טב יקוחו למשח ירישכמב שומיש יקוח יפ לע .ילמשח רצק רוסיא םייק ,תוחי

UL ב וא- CSA לש דוק םהילע עיפומ ראשכ)

ב םיכמסומה םילבכב שמתשהל-

UL/CSA( רחא ילמשח רצומ לכ רובע.דבלב ורקימקרפוס ידי לע ןיוצ אלש

ﺐﻴﻛﺮﺗ ﺪﻨﻋ ﻡﺍﺪﺨﺘﺳﺍ ﺐﺠﻳ ﺯﺎﻬﺠﻟﺍ ﻭ،ﻞﻴﺻﻮﺘﻟﺍ ﺕﻼﺑﺎﻛ ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﺕﻼﺑﺎﻜﻟﺍ

ﺕﻻﻮﺤﻣﻭ ﺩﺩﺮﺘﻤﻟﺍ ﺭﺎﻴﺘﻟﺍ

. ﻥﺃ ﻱﺃ ﻡﺍﺪﺨﺘﺳﺍ ﺕﻼﺑﺎﻛ ﺕﻻﻮﺤﻣﻭ ﻯﺮﺧﺃ ﺐﺒﺴﺘﻳ ﻲﻓ ﻞﻄﻋ ﺙﻭﺪﺣ ﻖﻳﺮﺣ ﻭﺃ . ﻲﺘﻟﺍ

ﻚﻟ ﺎﻫﺮﻴﻓﻮﺗ ﻢﺗ ﺞﺘﻨﻤﻟﺍ ﻊﻣ

UL ﻭﺃ CSA ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﺓﺰﻬﺟﻷﺍ ﺩﺍﻮﻣﻭ ﻥﻮﻧﺎﻗ ﺔﻣﻼﺴﻟﺍ ﻡﺍﺪﺨﺘﺳﺍ ﺮﻈﺤﻳ ﺕﻼﺑﺎﻜﻟﺍ

ﻞﺒﻗ ﻦﻣ ﺓﺪﻤﺘﻌﻣ

Supermicro ﺓﺰﻬﺟﺃ ﻯﺮﺧﺃ ﺔﻴﺋﺎﺑﺮﻬﻛ ﺮﻴﻏ ﺕﺎﺠﺘﻨﻤﻟﺍ ﺔﻨﻴﻌﻤﻟﺍ ﻞﺒﻗ ﻦﻣ ﻱﻷ

(UL/CSA ﻞﻤﺤﺗ ﻲﺘﻟﺍﺔﻣﻼﻋ )

경고!

제품을 설치할 때에는 제공되거나 지정된 연결케이블과 전원케이블, AC어댑터를
사용해야 합니다. 그 밖의 다른 케이블들이나 어댑터들은 고장 또는 화재의 원인이
될 수 있습니다. 전기용품안전법 (Electrical Appliance and Material Safety
Law)은 슈퍼마이크로에서 지정한 제품들 외에는 그 밖의 다른 전기 장치들을
위한 UL또는 CSA에서 인증한 케이블(전선 위에 UL/CSA가 표시)들의 사용을
금지합니다.

Waarschuwing

Bij het installeren van het product, gebruik de meegeleverde of aangewezen kabels,
stroomkabels en adapters. Het gebruik van andere kabels en adapters kan leiden
tot een storing of een brand. Elektrisch apparaat en veiligheidsinformatiebladen wet
verbiedt het gebruik van UL of CSA gecertifi ceerde kabels die UL of CSA die op
de code voor andere elektrische apparaten dan de producten die door Supermicro
alleen.

4-19

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Notes

4-20

Chapter 5: Advanced Serverboard Setup

Chapter 5

Advanced Serverboard Setup

This chapter covers the steps required to install processors and heatsinks to the
X9DRW-3LN4F+/X9DRW-3TF+ serverboard, connect the data and power cables
and install add-on cards. All serverboard jumpers and connections are described
and a layout and quick reference chart are included in this chapter. Remember to
close the chassis completely when you have fi nished working on the serverboard
to protect and cool the system suffi ciently.

5-1 Handling the Serverboard

Static electrical discharge can damage electronic com ponents. To prevent damage
to printed circuit boards, it is important to handle them very carefully (see Chapter 4).
Also note that the size and weight of the serverboard can cause it to bend if handled
improperly, which may result in damage. To prevent the serverboard from bending,
keep one hand under the center of the board to support it when handling.

The following measures are generally suffi cient to protect your equipment from
static discharge.

Precautions

• Use a grounded wrist strap designed to prevent static discharge.

• Touch a grounded metal object before removing any board from its antistatic

bag.

• Handle a board by its edges only; do not touch its components, peripheral chips,

memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the serverboard, add-on cards and peripherals back into their antistatic

bags when not in use.

Unpacking

The serverboard is shipped in antistatic packaging to avoid static damage. When
unpacking the board, make sure the person handling it is static protected.

5-1

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

OPEN 1st

WARNING!

OPEN 1st

WARNING!

5-2 Installing the Processor and Heatsink

Warning: When handling the processor package, avoid placing direct pressure on the

label area of the fan.

Notes:

• Always connect the power cord last and always remove it before adding, re-

moving or changing any hardware components. Make sure that you install the
processor into the CPU socket before you install the CPU heatsink.

• If you buy a CPU separately, make sure that you use an Intel-certifi ed multi-

directional heatsink only.

• Make sure to install the serverboard into the chassis before you install the CPU

heatsinks.

• When receiving a serverboard without a processor pre-installed, make sure that

the plastic CPU socket cap is in place and none of the socket pins are bent;
otherwise, contact your retailer immediately.

• Refer to the Supermicro web site for updates on CPU support.

Installing an LGA2011 Processor

Press down on

1. There are two levers on the

LGA2011 socket. First press and
release the load lever labeled
'Open 1st' on CPU Socket #1.

2. Press the second load lever

labeled 'Close 1st' to release the
load plate from its locked position.

Pull lever away
from the socket

the lever labeled

'Close 1st'

WARNING!

OPEN 1st

WARNING!

OPEN 1st

5-2

3. With the lever labeled 'Close 1st'

WARNING!

OPEN 1st

WARNING!

fully retracted, gently push down
on the 'Open 1st' lever to open the
load plate. Lift the load plate to
open it completely.

4. Using your thumb and the index
fi nger, remove the 'WARNING'
plastic cap from the socket.

5. Use your thumb and index fi nger
to hold the CPU by its edges. Align
the CPU keys, which are semi­circle cutouts, against the socket
keys.

6. Once they are aligned, carefully
lower the CPU straight down into
the socket. (Do not drop the CPU
on the socket. Do not move the
CPU horizontally or vertically and
do not rub the CPU against any
pins of the socket, which may
damage the CPU or the socket.)

Chapter 5: Advanced Serverboard Setup

WARNING!

OPEN 1st

Gently push
down to pop
the load plate
open.

WARNING!

Socket Keys

CPU Keys

5-3

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

OPEN 1s

t

OPEN 1st

Warning: You can only install the CPU to the socket in one direction. Make sure that
the CPU is properly inserted into the socket before closing the load plate. If it doesn't
close properly, do not force it as it may damage your CPU. Instead, open the load
plate again and double-check that the CPU is aligned properly.

7. With the CPU in the socket, in­spect the four corners of the CPU
to make sure that they are fl ush
with the socket.

8. Close the load plate. Lock the
lever labeled 'Close 1st', then lock
the lever labeled 'Open 1st'. Use
your thumb to gently push the
load levers down until the lever
locks.

9. Repeat steps to install a CPU to
CPU Socket #2 if needed.

Gently close

the load plate.

Push down and lock the

level labeled 'Close 1st'.

Lever Lock

OPEN 1st

OPEN 1st

Push down

and lock the

lever labeled

'Open 1st'.

5-4

Chapter 5: Advanced Serverboard Setup

Installing a CPU Heatsink

1. Place the heatsink on top of the CPU so that the four mounting holes are
aligned with those on the retention mechanism.

2. Screw in two diagonal screws (i.e. the #1 and the #2 screws) until just snug
(do not over-tighten the screws, which may damage the CPU.)

3. Finish the installation by fully tightening all four screws.

Removing the Heatsink

Warning: We do not recommend removing the CPU or the heatsink. If you do need

to remove the heatsink, please follow the instructions below to prevent damage to the
CPU or other components.

1. Unplug the power cord from the power supply.

1. Unscrew and remove the heatsink screws in the
sequence shown in the picture below.

2. Hold the heatsink and gently wiggle it to loosen it
from the CPU. (Do not use excessive force when
doing this!)

3. Once the heatsink is loosened, remove it from
the CPU.

4. Clean the surface of the CPU and the heatsink
to get rid of the old thermal grease. Reapply the
proper amount of thermal grease before you re­install the heatsink.

5-5

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

5-3 Connecting Cables

Now that the processors are installed, the next step is to connect the cables to
the serverboard.

Connecting Data Cables

The cables used to transfer data from the peripheral devices have been carefully
routed in preconfi gured systems to prevent them from blocking the fl ow of cooling
air that moves through the system from front to back. If you need to disconnect any
of these cables, you should take care to reroute them as they were originally after
reconnecting them (make sure the red wires connect to the pin 1 locations). If you
are confi guring the system, keep the airfl ow in mind when routing the cables.

The following data cables (with their connector locations noted) should be connect­ed. See the serverboard layout diagram in this chapter for connector locations.

• SAS (SAS0-SAS3) or SATA (SATA0-3) cables

• Control Panel cable (JF1, see next page)

Connecting Power Cables

The X9DRW-3LN4F+/X9DRW-3TF+ has a 24-pin primary power supply connector
designated JPW1 for connection to the ATX power supply. Connect the appropriate
connector from the power supply to JPW1 to supply power to the serverboard.
See the Connector Defi nitions section in this chapter for power connector pin
defi nitions.

In addition, your power supply must be connected to the 8-pin Processor Power
connectors at JPW2 and JPW3.

Connecting the Control Panel

JF1 contains header pins for various front control panel connectors. See Figure 5-1
for the pin locations of the front control panel buttons and LED indicators. Please
note that even and odd numbered pins are on opposite sides of each header.

All JF1 wires have been bundled into single keyed ribbon cable to simplify their
connection. The red wire in the ribbon cable plugs into pin 1 of JF1. Connect the
other end of the cable to the Control Panel printed circuit board, located just behind
the system status LEDs in the chassis.

See the Connector Defi nitions section in this chapter for details and pin descrip-
tions of JF1.

5-6

Chapter 5: Advanced Serverboard Setup

Figure 5-1. Front Control Panel Header Pins (JF1)

20 19

Ground

NMI

x (key)

Power LED

HDD LED

NIC1 Link LED

NIC2 Link LED

Blue: OH/Fan Fail/Power Fail/UID LED

Power Fail LED

Ground

Ground

2 1

x (key)

3.3V

UID Switch/Vcc

NIC1 Active LED

NIC2 Active LED

Red: (Blue LED Cathode)

3.3V

Reset Button

Power Button

5-4 I/O Ports

The I/O ports are color coded in conformance with the PC 99 specifi cation. See
Figure 5-2 below for the colors and locations of the various I/O ports.

Figure 5-2. Rear Panel I/O Ports

2

5

1

4
3

*LAN3 and LAN4 are 10 Gb ports on the 6017R-N3RFT+ (X9DRW-3TF+).

6 7 8 9 10 11 12

Rear I/O Ports

1. Keyboard 7. VGA Port

2. PS/2 Mouse 8. LAN1 Port

3. USB0 9. LAN2 Port

4. USB1 10. LAN3 Port*

5. Dedicated IPMI LAN 11. LAN4 Port*

6. COM1 12. UID Button

5-7

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

5-5 Installing Memory

Note: Check the Supermicro web site for recommended memory modules.

CAUTION

Exercise extreme care when installing or removing DIMM modules

to prevent any possible damage.

Installing DIMMs

1. Insert the desired number of DIMMs into the memory slots, starting with slot
P1-DIMMA1. For best performance, install memory modules of the same type
and same speed in the slots as indicated in the tables below.

2. Insert each DIMM vertically into its slot. Pay attention to the notch along the
bottom of the module to prevent inserting the DIMM module incorrectly (see
Figure 5-3).

3. Gently press down on the DIMM module until it snaps into place in the slot.
Repeat for all modules

Memory Support

The X9DRW-3LN4F+/X9DRW-3TF+ has 24 memory sockets that can support up
to 768 GB of ECC registered DDR3-1333/1066/800 RDIMMs or up to 192 GB of
unbuffered DDR3-1333/1066/800 UDIMMs. Please refer to Chapter 5 for installing
memory.

Note: Memory speed support depends on the type of CPU used.

Figure 5-3. Installing DIMM into Slot

Notch

To In sta ll : Insert module
vertically and press
down until it snaps into
place. Pay attention to
the alignment notch at
the bottom.

Front View

Notch

To Remove:

Use your thumbs to
gently push the release
tabs near both ends of
the module. This should
release it from the slot.

Release Tab

Note: Notch should align
with the receptive key
point on the slot.

Top View of DDR3 Slot

5-8

Release Tab

Chapter 5: Advanced Serverboard Setup

Processor & Memory Module Population Confi guration

For memory to work properly, follow the tables below for memory installation.

Processors and their Corresponding Memory Modules

CPU# Corresponding DIMM Modules

CPU 1 P1-A1P1-A2P1-A3P1-B1P1-B2P1-B3P1-C1P1-C2P1-C3P1-D1P1-D2P1-

CPU2 P2-E1P2-E2P2-E3P2-F1P2-F2P2-F3P2-G1P2-G2P2-G3P2-H1P2-H2P2-

Processor and Memory Module Population

Number of

CPUs+DIMMs

1 CPU &

2 DIMMs

1 CPU &

4 DIMMs

1 CPU &

5~8 DIMMs

2 CPUs &

4 DIMMs

CPU1
P1-A1/P1-B1

CPU1
P1-A1/P1-B1, P1-C1/P1-D1

CPU1
P1-A1/P1-B1, P1-C1/P1-D1, P1-A2/P1-B2, P1-C2/P1-D2

CPU1 + CPU2
P1-A1/P1-B1, P2-E1/P2-F1

CPU and Memory Population Confi guration Table

(For memory to work properly, please follow the tables below.)

D3

H3

2 CPUs &

6 DIMMs

2 CPUs &

8 DIMMs

2 CPUs &

9~12 DIMMs

2 CPUs &

13 DIMMs~24

DIMMs

CPU1 + CPU2
P1-A1/P1-B1, P2-E1/P2-F1, P1-C1/P1-D1

CPU1 + CPU2
P1-A1/P1-B1, P2-E1/P2-F1, P1-C1/P1-D1, P2-G1/P2-H1

CPU1/CPU2
P1-A1/P1-B1, P2-E1/P2-F1, P1-C1/P1-D1, P2-G1/P2-H1, P1-A2/P1-B2, P2-E2/P2-F2

CPU1/CPU
P1-A1/P1-B1, P2-E1/P2-F1, P1-C1/P1-D1, P2-G1/P2-H1, P1-A2/P1-B2, P2-E2/P2-F2,
P1-C2/P1-D2, P2-G2/P2-H2, P1-A3/P1-B3, P2-E3/P2-F3, P1-C3/P1-D3, P2-G3/P2-H3

5-9

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

UDIMM Support

DIMMs Populated per

DDR Channel

1 ECC/Non-ECC DDR3 1066, 1333 SR, DR

2 ECC/Non-ECC DDR3 1066, 1333 SR, DR

DIMMs Populated per

DDR Channel

1 Reg. ECC DDR3 1066, 1333, 1600 SR, DR

2 Reg. ECC DDR3 1066, 1333,1600 SR, DR

3 Reg. ECC DDR3 800, 1066 SR, DR

1 Reg. ECC DDR3 1066 QR

2 Reg. ECC DDR3 800 QR

UDIMM Type
(Unb. DIMM)

RDIMM Support

RDIMM Type

(Reg. DIMM)

POR Speeds (in

MHz)

POR Speeds (in

MHz)

(Any Combination)

(Any Combination)

Ranks per DIMM

Ranks per DIMM

LRDIMM Support

DIMMs Populated per

DDR Channel

1 LR ECC DDR3 1066, 1333 QR

2 LR ECC DDR3 1066, 1333 QR

3 LR ECC DDR3 1066 QR

LRDIMM Type

(Load Reduced

DIMM)

POR Speeds (in

MHz)

Ranks per DIMM

(Any Combination)

Note

All channels in a system will run at the fastest common frequency.

5-10

Chapter 5: Advanced Serverboard Setup

5-6 Adding PCI Cards

PCI Expansion Slots

Riser cards installed to the system allow you to add PCI expansion cards (see be­low). The SC819TQ-R700WB can support the use of two standard size (full-height,
half-length) expansion cards and one low-profi le (4.1" length) expansion card (with
pre-installed riser cards).

PCI Card Installation

Before installing a PCI add-on card, make sure you power off the system fi rst. Begin
by removing the top chassis cover. Two riser cards should be pre-installed into the
system. Remove the latch from the expansion card slot at the rear of the chassis
then lift the riser card assembly from the chassis. Insert the PCI card into the riser
card slot, pushing down with your thumbs evenly on both sides of the card - note
that the add-on card attaches to the riser card with a single screw. After the card has
been installed, reinstall the riser card then reinsert the latch back into the expansion
card slot. Finish by replacing the chassis cover.

PCI Slot/Card Confi gurations

Riser Card Expansion Card Supported

RSC-R1UW-2E16 (left side) 1x PCI-E x16 and 1x PCI-E x8 cards (full-height, half-length)

RSC-R1UW-E8R (right side) 1x low-profi le PCI-E x8 card (4.1" length)

1

2
3

PCI Card Locations

# Expansion Card # Expansion Card

1 Low-profi le (2.536"), 4.1" length 3 Full-height (4.2"), 6.6" length

2 Full-height (4.2"), 10" length

5-11

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

5-7 Serverboard Details

Figure 5-4. SUPER X9DRW-3TF+/X9DRW-3TF+ Layout

PLD

JPBR1

JPG1

SAS4~7

JPME1

JPB1

JBT1

SAS0~3

CPLD

Clock

BMC
CTRL

JPP0

LEM1

JPP1

JP7
JP6

BATTERY

JBAT1

SXB1A

SXB1B

SXB1C

SXB1D

CPU2_PORT2C

CPU2_PORT2A

CPU1_PORT3A

CPU1_PORT2CCPU1_PORT2A

SXB1_3

1

CPU1_PORT3C

SXB1_4

JUIDB1

LE2

UID

SXB2

CPU2_PORT3A

JI2C2

JI2C1

CPU2_PORT3B

CPU2_PORT3C

CPU2_PORT3D

P2-DIMME2

P2-DIMM1A

P2-DIMME1

LAN4

P2-DIMME3

LAN3

P2-DIMMF2

P2-DIMMF1

LAN
CTRL 2

P2-DIMMF3

LAN2

LAN1

X9DRW-3LN4F+

Rev. 1.21

CPU2

VGA1

LAN
CTRL 1

JPL2

JPL1

Buzzer

SP1

COM1

P2-DIMMH3

USB0/1

IPMI_LAN

P2-DIMMH2

P2-DIMMH1

KB/MOUSE

JPW4

P2-DIMMG2

P2-DIMMG3

P2-DIMMG1

Intel

PCH

USB6

USB2/3

COM2

BIOS

JWD1

USB4/5

JOH1

JSD1

JPME2

JL1

I-SATA2

I-SATA1

I-SATA0

JWP1

JSTBY1

I-SATA5

I-SATA4

I-SATA3

JTPM1

TPM

LE1

JF1

T-SGPIO1

JRK1

JF2

T-SGPIO2

FANA

FAN5

P1-DIMMC1

P1-DIMMC2

P1-DIMMD1

P1-DIMMC3

P1-DIMMD3

P1-DIMMD2

FAN4

CPU1

Notes:

Jumpers not indicated are for test purposes only.

JIPMB1

FAN3

FAN2

P1-DIMMB2

P1-DIMMB3

P1-DIMMA3

P1-DIMMB1

P1-DIMMA1

P1-DIMMA2

JPW3

PWR_I2C

JPI2C1

JPW2

JPW1

FAN1

5-12

Chapter 5: Advanced Serverboard Setup

X9DRW-3LN4F+/X9DRW-3TF+ Quick Reference

Jumper Description Default Setting

JBT1 Clear CMOS See Section 5-9

2

JI

C1/JI2C2 SMB to PCI-E Slots Pins 2-3 (Normal)
JPB1 BMC Enable/Disable Pins 1-2 (Enabled)

JPG1 VGA Enable/Disable Pins 1-2 (Enabled)

JPL1 LAN1/LAN2 Enable/Disable Pins 1-2 (Enabled)

JPL2 LAN3/LAN4 Enable/Disable Pins 1-2 (Enabled)

JWD1 Watch Dog Pins 1-2 (Reset)

Connector Description

COM1/COM2 Backplane COM Port1/Front Accessible COM2 Header

FAN1~5, FANA CPU/System Fan Headers

I-SATA 0~5 Intel SB SATA Ports 0~5

JF1 Front Panel Control Header

JF2 LAN 3/4 Link/Activity LED Indicators

JIPMB1 4-pin External BMC I

2

C Header (for IPMI Card)

JL1 Chassis Intrusion Header

JOH1 Overheat/Fan Fail LED Header

2

JPI

C1 Power Supply SMBbus I2C Header

JPW1 ATX 24-Pin Power Connector

JPW2/JPW3 12V 8-Pin Power Connectors

JPW4 12V 4-Pin Power Connector

JRK1 RAIDKey

JSD1 SATA DOM (Device On Module) Power Connector

JSTBY1 Standby Power Header

JTPM1 TPM (Trusted Platform Module)/Port 80

KB/Mouse Keyboard/Mouse

LAN1/2 G-bit Ethernet LAN Ports 1/2

LAN3/4 1 GB (X9DRW-3LN4F+)/10 GB ((X9DRW-3TF+) Ports

(IPMI) LAN Dedicated IPMI LAN Port

SAS 0~3, 4~7 SAS Ports 0~3, 4~7

Quick Reference table continued on next page.

5-13

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

SP1 Onboard Buzzer (Internal Speaker)

SXB1A/1B/1C SMC-Proprietary WIO_L (Left) Add-On Card Slot

SXB2 SMC-Proprietary WIO_R (Right) Add-On Card Slot

T-SGPIO 1/2 Serial-Link General_Purpose IO Headers (J17/J18)

USB 0/1 Rear I/O USB 0/1 Ports

USB 2/3, 4/5 Front Accessible USB 2/3, 4/5 Headers

USB 6 Front Panel Type A USB 6 Port

UID Switch UID (Unit Identifi er) Switch (JUID1)

VGA1 Rear I/O VGA Port

LED Description State Status

LE1 Standby PWR LED Green: On SB Power On

LE2 UID LED

LEM1 BMC Heartbeat LED Green: Blinking Normal

Blue: On (Windows OS),
Blinking (Linux)

Unit Identifi ed

5-14

Chapter 5: Advanced Serverboard Setup

5-8 Connector Defi nitions

ATX Power Connector

The primary ATX power supply con­nector meets the SSI EPS 12V speci­fi cation. Make sure that the orientation
of the connector is correct. See the
table on the right for pin defi nitions.

Processor Power Connectors

JPW2 and JPW3 must also be con­nected to the power supply to provide
power for the processor(s). See the
table on the right for pin defi nitions.

ATX Power 24-pin Connector

Pin Defi nitions

Pin# Defi nition Pin # Defi nition

13 +3.3V 1 +3.3V

14 -12V 2 +3.3V

15 COM 3 COM

16 PS_ON 4 +5V

17 COM 5 COM

18 COM 6 +5V

19 COM 7 COM

20 Res (NC) 8 PWR_OK

21 +5V 9 5VSB

22 +5V 10 +12V

23 +5V 11 +12V

24 COM 12 +3.3V

12V 8-Pin Power Connector

Pin Defi nitions

Pins Defi nition

1 through 4 Ground

5 through 8 +12V

4-pin Power Connectors

JPW4 should also be connected to
the power supply. See the table on
the right for pin defi nitions.

12V 4-pin Power

Connector

Pin Defi nitions

Pins Defi nition

1~2 Ground

3~4 +12V

Warning: To prevent damage to your power supply or serverboard, please use a power
supply that contains a 24-pin and two 8-pin power connectors. Be sure to connect
these power connectors to the 20-pin and the two 8-pin power connectors on your
serverboard for adequate power supply to your system. Failure to do so will void the
manufacturer warranty on your power supply and serverboard.

5-15

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

NMI Button

The non-maskable interrupt button
header is located on pins 19 and 20
of JF1. Refer to the table on the right
for pin defi nitions.

Power LED

The Power LED connection is located
on pins 15 and 16 of JF1. Refer to the
table on the right for pin defi nitions.

HDD LED/UID Switch

The HDD LED/UID switch connec­tions are located on pins 13/14 of JF1.
Attach an LED cable to display HDD
activity. This connection can also be
used as a front panel UID (Unit Identi­fi er) switch. The UID LED on pin 7 of
JF1 works in conjunction with this UID
switch. When the user presses and
releases the UID switch, the UID LED
will be turned on or off to indicate the
location of the unit.

NMI Button

Pin Defi nitions (JF1)

Pin# Defi nition

19 Control

20 Ground

Power LED

Pin Defi nitions (JF1)

Pin# Defi nition

15 Vcc

16 Control

HDD/UID Switch

Pin Defi nitions (JF1)

Pin# Defi nition

13 UID Signal/3.3V SB

14 HD Active

NIC1 LED

The NIC1 (Network Interface Control­ler) LED connection is located on pins
11 and 12 of JF1. Attach the NIC1
LED cable to display network activity.
Refer to the table on the right for pin
defi nitions.

NIC2 LED

The NIC2 (Network Interface Control­ler) LED connection is located on
pins 9 and 10 of JF1. Attach the NIC2
LED cable to display network activity.
Refer to the table on the right for pin
defi nitions.

5-16

NIC1 LED

Pin Defi nitions (JF1)

Pin# Defi nition

11 Vcc

12 Ground

NIC2 LED

Pin Defi nitions (JF1)

Pin# Defi nition

9 Vcc

10 Ground

Chapter 5: Advanced Serverboard Setup

Overheat (OH)/Fan Fail/PWR Fail/
UID LED

Connect an LED to pins 7 and 8 of
JF1 to provide advanced warning of
chassis overheating or fan failure.
These pins also work with the front
UID indicator, which will activate as
either a solid or fl ashing blue LED
depending on whether the LED was
activated via IPMI or the UID button.
Refer to the tables on the right for pin
defi nitions and status indicators.

Power Fail LED

The Power Fail LED connection is
located on pins 5 and 6 of JF1. Refer
to the table on the right for pin defi ni-
tions.

OH/Fan Fail/ PWR Fail/Blue_UID

LED Pin Defi nitions (JF1)

Pin# Defi nition

7 Blue_LED Cathode (UID)

8 OH/Fan Fail/PWR Fail/UID LED

OH/Fan Fail/PWR Fail LED Status

Pin 7 Pin 8 Red LED Blue LED

Low High On: OH/FF/Pwr Fail

(Solid On: OH
Fast Blinking: Fan Fail
Slow Blinking: Pwr Fail)

High Low Off (System normal) On

High High Off Off

Power Fail LED

Pin Defi nitions (JF1)

Pin# Defi nition

5 Vcc

6 Ground

Off

UID LED

Reset Button

The Reset Button connection is lo­cated on pins 3 and 4 of JF1. Attach
it to the hardware reset switch on the
computer case. Refer to the table on
the right for pin defi nitions.

Power Button

The Power Button connection is
located on pins 1 and 2 of JF1. Mo­mentarily contacting both pins will
power on/off the system. This button
can also be confi gured to function
as a suspend button (see the Power
Button Mode setting in BIOS). To turn
off the power when set to suspend
mode, depress the button for at least
4 seconds. Refer to the table on the
right for pin defi nitions.

Reset Button

Pin Defi nitions (JF1)

Pin# Defi nition

3 Reset

4 Ground

Power Button

Pin Defi nitions (JF1)

Pin# Defi nition

1 PW_ON

2 Ground

5-17

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Fan Headers

The serverboard has six system/
CPU fan headers (Fan 1~Fan 5, Fan
A). All are 4-pin fans headers, which
are backward compatible with tradi­tional 3-pin fans. Fan speed control is
available for 4-pin fans only. The fan
speeds are controlled by IPMI. See
the table on the right for pin defi nitions.

Chassis Intrusion

A Chassis Intrusion header is located
at JL1. Attach an appropriate cable
from the chassis to inform you of a
chassis intrusion when the chassis
is opened.

Fan Header

Pin Defi nitions

Pin# Defi nition

1 Ground

2 +12V

3 Tachometer

4 PWR Modulation

Chassis Intrusion

Pin Defi nitions

Pin# Defi nition

1 Intrusion Input

2 Ground

Internal Speaker

The Internal Speaker, located at SP1,
can be used to provide audible indica­tions for various beep codes. See the
table on the right for pin defi nitions.
Refer to the layout below for the lo­cations of the Internal Buzzer (SP1).

Overheat/Fan Fail LED

The JOH1 header is used to connect
an LED indicator to provide warnings
of chassis overheating and fan failure.
This LED will blink when a fan failure
occurs. Refer to the tables on right for
pin defi nitions.

Internal Buzzer (SP1)

Pin Defi nition

Pin# Defi nitions

Pin 1 Pos. (+) Beep In

Pin 2 Neg. (-) Alarm

Speaker

OH/Fan Fail LED

Status

State Message

Solid Overheat

Blinking Fan Fail

5-18

Chapter 5: Advanced Serverboard Setup

TPM Header/Port 80

A Trusted Platform Module/Port 80
header is located at JTPM1 to provide
TPM support and Port 80 connection.
Use this header to enhance system
performance and data security. See
the table on the right for pin defi ni-
tions.

Standby Power Header

The Standby Power header is located
at JSTBY1. See the table on the right
for pin definitions. (You must also
have a cable to use this feature.)

TPM/Port 80 Header

Pin Defi nitions

Pin # Defi nition Pin # Defi nition

1 LCLK 2 GND

3 LFRAME# 4 <(KEY)>

5 LRESET# 6 +5V (X)

7 LAD 3 8 LAD 2

9 +3.3V 10 LAD1

11 LAD0 12 GND

13 SMB_CLK4 14 SMB_DAT4

15 +3V_DUAL 16 SERIRQ

17 GND 18 CLKRUN# (X)

19 LPCPD# 20 LDRQ# (X)

Standby PWR

Pin Defi nitions

Pin# Defi nition

1 +5V Standby

2 Ground

3 Wake-up

Power SMB (I2C) Connector

Power System Management Bus (I
(connector at JPI

2

C1) monitors power

2

C)

supply, fan and system temperatures.
See the table on the right for pin
defi nitions.

IPMB

A System Management Bus header
for IPMI 2.0 is located at JIPMB1.
Connect the appropriate cable here
to use the IPMB I

2

C connection on

your system.

PWR SMB

Pin Defi nitions

Pin# Defi nition

1 Clock

2 Data

3 PWR Fail

4 Ground

5 +3.3V

IPMB Header

Pin Defi nitions

Pin# Defi nition

1 Data

2 Ground

3 Clock

4 No Connection

5-19

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

T-SGPIO 1/2 Headers

T-SGPIO

Two SGPIO (Serial-Link General
Purpose Input/Output) headers are
located at J17 and J18. These head­ers support Serial Link interface for
onboard SATA connections. See the
table on the right for pin defi nitions.

Pin# Defi nition Pin Defi nition

1NC 2 NC

3 Ground 4 Data

5 Load 6 Ground

7 Clock 8 NC

Note: NC indicates no connection.

Pin Defi nitions

DOM Power Connector

A power connector for SATA DOM
(Disk On Module) devices is located at
JSD1. Connect an appropriate cable
here to provide power support for your
DOM devices.

RAIDKey Header

A RAIDKey header (JRK1) provides
RAID function support to enhance
system performance.

10G LAN3/LAN4 LED Indicators
(X9DRW-3TF+ Only)

DOM PWR

Pin Defi nitions

Pin# Defi nition

1 +5V

2 Ground

3 Ground

RAIDKey

Pin Defi nitions

Pin# Defi nition

1 Ground

2 Signal

3 Ground

The NIC (Network Interface Control­ler) LED connections for 10G LAN
port 3 are located on pins 3 and 4 of
JF2, and the LED connections for 10G
LAN port 4 is on Pins 1 and 2 of JF2.
Attach NIC LED cables here to display
network activities. Refer to the table
on the right for pin defi nitions.

Note: The NIC LED connections for
LAN Ports 1/2 are located on JF1.

10G LAN Ports 3/4 LED Indicators (JF2)

Pin Defi nitions

Pin# Defi nition Pin Defi nition

1 LAN4 Activity 2 LAN4 Link

3 LAN3 Activity 4 LAN3 Link

5-20

Unit Identifi er Switch

The UID switch is located next to the
10G LAN 4 port on the backplane.
The rear UID LED (LE2) is located
next to the UID switch. The Front
Panel UID LED is located on pins
7/8 of JF1. Connect a cable to pin
8 on JF1 for Front Panel UID LED
indication. When you press the UID
switch, both the rear UID LED and
Front Panel UID LED indicators will
be turned on. Press the UID switch
again to turn off both LED indicators.
These UID indicators provide easy
identifi cation of a system unit that
may be in need of service.

Note: UID can also be triggered via
IPMI on the serverboard. For more
information on IPMI, please refer to
the IPMI User's Guide posted on our
Website @http://www.supermicro.
com.

Chapter 5: Advanced Serverboard Setup

UID Switch

Pin# Defi nition

1 Ground

2 Ground

3 Button In

4 Ground

UID LED (LE2)

Status

Color/State OS Status

Blue: On Windows OS Unit Identifi ed

Blue:
Blinking

Linux OS Unit Identifi ed

Ethernet Ports

Two Gb LAN ports (LAN1/2) and two
10Gb LAN ports (LAN3/4) are located
on the I/O backplane to provide Eth­ernet connections. LAN3/LAN4 ports
support 1Gb connections on the

-3LN4F+, and 10Gb connections on
the -3TF+. In addition, a dedicated
IPMI LAN, located above USB 0/1
ports on the backplane, provides KVM
support for IPMI 2.0. All these ports
accept RJ45 type cables.

5-21

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Serial Ports

Two COM connections (COM1 &
COM2) are located on the serverboard.
COM1 is located on the Backplane I/O
panel. COM2, located close to USB 4/5
Connectors, is used to provide front
access support. See the table on the
right for pin defi nitions.

ATX PS/2 Keyboard and Mouse
Ports

The ATX PS/2 keyboard and PS/2
mouse are located next to the Back
Panel USB Ports 0/1 and the IPMI LAN
port on the serverboard. See the table
at right for pin defi nitions.

Serial COM) Ports

Pin Defi nitions

Pin # Defi nition Pin # Defi nition

1 DCD 6 DSR

2 RXD 7 RTS

3 TXD 8 CTS

4 DTR 9 RI

5 Ground 10 N/A

PS/2 Keyboard/Mouse Pin

Defi nitions

PS2 Keyboard PS2 Mouse

Pin# Defi nition Pin# Defi nition

1 KB Data 1 Mouse Data

2 No Connection 2 No Connection

3 Ground 3 Ground

4 Mouse/KB VCC

(+5V)

5 KB Clock 5 Mouse Clock

6 No Connection 6 No Connection

VCC: with 1.5A PTC (current limit)

4 Mouse/KB VCC

(+5V)

Universal Serial Bus (USB)

Two Universal Serial Bus ports (USB
0/1) are located on the I/O back panel.
In addition, two USB headers, located
close to the I-SATA ports, provide four
front-accessible USB connections
(USB 2/3, USB 4/5). A Type A connec­tor (USB 6) also supports front panel
USB connections. (Cables are not
included). See the tables on the right
for pin defi nitions.

Backplane USB

(USB 0/1)

Pin Defi nitions

Pin# Defi nition

1 +5V

2 PO-

3 PO+

4 Ground

5NA

5-22

FP USB (2/3, 4/5, 6)

Pin Defi nitions

USB 2, 4, 6
Pin # Defi nition

1 +5V 1 +5V

2 PO- 2 PO-

3 PO+ 3 PO+

4 Ground 4 Ground

5 NC 5 Key

(NC= No connection)

USB 3, 5
Pin # Defi nition

5-9 Jumper Settings

Explanation of Jumpers

To modify the operation of the
serverboard, jumpers can be used
to choose between optional settings.
Jumpers create shorts between two
pins to change the function of the
connector. Pin 1 is identifi ed with a
square solder pad on the printed cir­cuit board. See the diagram at right for
an example of jumping pins 1 and 2.
Refer to the serverboard layout page
for jumper locations.

Note: On two-pin jumpers, "Closed"
means the jumper is on and "Open"
means the jumper is off the pins.

Chapter 5: Advanced Serverboard Setup

Connector

Pins

Jumper

Setting

3 2 1

3 2 1

CMOS Clear

JBT1 is used to clear CMOS and will also clear any passwords. Instead of pins,
this jumper consists of contact pads to prevent accidentally clearing the contents
of CMOS.

To clear CMOS

1. First power down the system and unplug the power cord(s).

2. With the power disconnected, short the CMOS pads with a metal object such

as a small screwdriver.

3. Remove the screwdriver (or shorting device).

4. Reconnect the power cord(s) and power on the system.

Note: Do not use the PW_ON connector to clear CMOS.

VGA Enable/Disable

JPG1 allows you to enable or disable
the onboard VGA port. The default
position is on pins 1 and 2 to enable
VGA. See the table on the right for
jumper settings. The default setting

VGA Enable/Disable

Jumper Settings

Jumper Setting Defi nition

Pins 1-2 Enabled

Pins 2-3 Disabled

is enabled.

5-23

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

JPL1/JPL2

LAN Port

Use JPL1 to enable/disable LAN ports
1/2, and use JPL2 for LAN ports
3/4. See the table on the right for
jumper settings. The default setting
is Enabled.

Watch Dog Enable/Disable

JWD1 controls the Watch Dog function.
Watch Dog is a system monitor that
can reboot the system when a software
application “hangs”. Pins 1-2 will cause
WD to reset the system if an applica­tion hangs. Pins 2-3 will generate a
non-maskable interrupt signal for the
application that has hung. See the table
on the right for jumper settings. Watch
Dog must also be enabled in BIOS.

Jumper Settings

Jumper Setting Defi nition

Pins 1-2 Enabled

Pins 2-3 Disabled

Watch Dog

Jumper Settings

Jumper Setting Defi nition

Pins 1-2 Reset

Pins 2-3 NMI

Open Disabled

SMB to PCI Express Slots

Jumpers JI

2

C1 and JI2C2 allow you to

connect the System Management Bus

2

(I

C) to the PCI Express slots. Both
jumpers must have the same setting to
function correctly. The default setting is
disabled. See the table on the right for
jumper settings.

BMC Enable

Jumper JPB1 allows you to enable the
embedded the Nuvoton BMC (Base­board Management) Controller to pro­vide IPMI 2.O/KVM support on the
serverboard. See the table on the right
for jumper settings.

SMB to PCI-Exp

Jumper Settings

Jumper Setting Defi nition

Closed Enabled

Open Disabled

BMC Enable

Jumper Settings

Jumper Setting Defi nition

Pins 1-2 BMC Enable

Pins 2-3 Normal (Default)

5-24

5-10 Onboard Indicators

Chapter 5: Advanced Serverboard Setup

LAN LEDs

The Ethernet ports (located beside the
VGA port) have two LEDs. On each
Gigabit LAN port, one LED indicates
activity when blinking while the other
LED may be green, amber or off to
indicate the speed of the connection.
See the table on the right for details
on the connection speed LED.

Dedicated IPMI LAN LEDs

In addition to LAN1 and LAN2, a dedi­cated IPMI LAN is located on the I/O
backpanel. The amber LED indicates
activity, while the Link LED indicates
the speed of the connection. See the
tables at right for more information.

Activity LED

LAN LED

Connection Speed Indicator

LED Color Defi nition

Off No connection or 10 Mb/s

Green 100 Mb/s

Amber 1 Gb/s

Link LED

IPMI LAN Activity Indicator

Color Status Defi nition

Amber Flashing Active

IPMI LAN Indicator

LED Color Defi nition

Off No Connection or 10 Mb/s

Green 100 Mb/s

Link LED

Activity LED

LE1

An Onboard Power LED is located at
LE1. When this LED is lit the system is
on. Be sure to turn off the system and
unplug the power cord before removing
or installing components.

Rear UID LED

The rear UID LED is located at the
I/O backplane. This LED is used in
conjunction with the rear UID switch to
provide easy identifi cation of a system
that might be in need of service.

BMC Heartbeat LED

A BMC Heartbeat LED is located at
LEM1. When LEM1 is blinking, BMC
is functioning normally.

Onboard PWR LED Indicator

LED Color Defi nition

Off System Off/Power cable

Green System On

Color/State OS Status

Blue: On Windows Unit Identifi ed

Blue:
Blinking

not connected

UID LED

Linux Unit Identifi ed

BMC Heartbeat LED

Status

Color/State Defi nition

Green:
Blinking

BMC: Normal

5-25

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

5-11 SAS/SATA Port Connections

SATA Port Pin Defi nitions

SATA Ports

There are six Serial ATA Ports (I­SATA0~I-SATA 5) located on the
serverboard, including four SATA2
ports and two SATA3 ports. See the
table on the right for pin defi nitions.

SAS Ports

Eight Serial Attached SCSI Ports (SAS
0~3, 4~7) are provided on the serverboard
to provide serial link connections. These
ports are supported by the Intel PCH C606
controller. See the table on the right for pin
defi nitions.

Pin # Defi nition

1 Ground

2 TXP

3 TXN

4 Ground

5 RXN

6 RXP

7 Ground

SAS Port Pin Defi nitions

Pin # Defi nition

1 Ground

2 TXP

3 TXN

4 Ground

5 RXN

6 RXP

7 Ground

5-26

Chapter 5: Advanced Serverboard Setup

5-12 Installing Software

After the hardware has been installed, you should fi rst install the operating system
and then the drivers. The necessary drivers are all included on the Supermicro CDs
that came packaged with your serverboard.

Figure 5-5. Driver/Tool Installation Display Screen

Note: Click the icons showing a hand writing on paper to view the readme fi les

for each item. Click the computer icons to the right of these items to install each
item (from top to the bottom) one at a time. After installing each item, you must
re-boot the system before moving on to the next item on the list. The bottom
icon with a CD on it allows you to view the entire contents of the CD.

5-27

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

SuperDoctor III

The SuperDoctor III program is a Web base management tool that supports remote
management capability. It includes Remote and Local Management tools. The local
management is called SD III Client. The SuperDoctor III program allows you to moni­tor the environment and operations of your system. Supero Doctor III displays crucial
system information such as CPU temperature, system voltages and fan status. See
the Figure below for a display of the Supero Doctor III interface.

Note: The default User Name and Password for SuperDoctor III is ADMIN / AD­MIN.

Note: When SuperDoctor III is fi rst installed, it adopts the temperature threshold
settings that have been set in BIOS. Any subsequent changes to these thresholds
must be made within SuperDoctor, as the SuperDoctor settings override the BIOS
settings. To set the BIOS temperature threshold settings again, you would fi rst need
to uninstall SuperDoctor III.

Figure 5-6. SuperDoctor III Interface Display Screen (Health Information)

5-28

Chapter 5: Advanced Serverboard Setup

Figure 5-7. SuperDoctor III Interface Display Screen (Remote Control)

Note: SD III Software Revision 1.0 can be downloaded from our Web Site at: ftp://
ftp.supermicro.com/utility/Supero_Doctor_III/. You can also download SDIII User's
Guide at: http://www.supermicro.com/manuals/other/SDIII_User_Guide.pdf. For
Linux, we will still recommend Supero Doctor II.

5-29

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

5-13 Onboard Battery

Please handle used batteries carefully. Do not damage the battery in any way; a
damaged battery may release hazardous materials into the environment. Do not
discard a used battery in the garbage or a public landfi ll. Please comply with the
regulations set up by your local hazardous waste management agency to dispose
of your used battery properly.

Figure 5-8. Installing the Onboard Battery

TUM TTER

TTER DER

Please handle used batteries carefully. Do not damage the battery in any way; a
damaged battery may release hazardous materials into the environment. Do not
discard a used battery in the garbage or a public landfi ll. Please comply with the
regulations set up by your local hazardous waste management agency to dispose
of your used battery properly.

5-30

Chapter 6: Advanced Chassis Setup

Chapter 6

Advanced Chassis Setup

This chapter covers the steps required to install components and perform mainte­nance on the SC819TQ chassis. For component installation, follow the steps in the
order given to eliminate the most common problems encountered. If some steps
are unnecessary, skip ahead to the next step.

Tools Required: The only tool you will need to install components and perform
maintenance is a Philips screwdriver.

6-1 Static-Sensitive Devices

Electrostatic Discharge (ESD) can damage electronic com ponents. To prevent
damage to any printed circuit boards (PCBs), it is important to handle them very
carefully. The following measures are generally suffi cient to protect your equipment
from ESD damage.

Precautions

• Use a grounded wrist strap designed to prevent static discharge.

• Touch a grounded metal object before removing any board from its antistatic

bag.

• Handle a board by its edges only; do not touch its components, peripheral chips,

memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the serverboard, add-on cards and peripherals back into their antistatic

bags when not in use.

• For grounding purposes, make sure your computer chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and
the serverboard.

6-1

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Figure 6-1. Chassis: Front and Rear Views

Control PanelSlim DVD-ROM (optional)

Hard Drive Bays (4)

Power Supplies

Mouse/Keyboard Ports

IPMI LAN

USB Ports

COM1 Port

PCI Expansion Slots (w/riser cards)

VGA Port

Ethernet (LAN) Ports*

6-2 Control Panel

The control panel (located on the front of the chassis) must be connected to the JF1
connector on the serverboard to provide you with system status indications. These
wires have been bundled together as a ribbon cable to simplify the connection.
Connect the cable from JF1 on the serverboard to the appropriate header on the
Control Panel PCB (printed circuit board). Make sure the red wire plugs into pin 1
on both connectors. Pull all excess cabling out of the airfl ow path.

The control panel LEDs inform you of system status. See "Chapter 3: System In­terface" for details on the LEDs and the control panel buttons. Details on JF1 can
be found in "Chapter 5: Advanced Serverboard Setup."

6-2

Chapter 6: Advanced Chassis Setup

6-3 System Fans

Five 4-cm heavy duty counter-rotating fans provide the cooling for the 6017R­N3RF4+/6017R-N3RFT+. Each fan unit is actually made up of two fans joined back­to-back, which rotate in opposite directions. This counter-rotating action generates
exceptional airfl ow and works to dampen vibration levels.

It is very important that the chassis top cover is properly installed and making a
good seal in order for the cooling air to circulate properly through the chassis and
cool the components. See Figure 6-2.

System Fan Failure

Fan speed is controlled by system temperature via a BIOS setting. If a fan fails,
the remaining fan will ramp up to full speed and the overheat/fan fail LED on the
control panel will turn on. Replace any failed fan at your earliest convenience with
the same type and model (the system can continue to run with a failed fan).

Remove the top chassis cover while the system is still running to determine which of
the fans has failed. Then power down the system before replacing a fan. Removing
the power cord(s) is also recommended as a safety precaution.

Replacing System Fans

1. After determining which fan has failed, turn off the power to the system.

2. Unplug the fan cable from the serverboard and remove the failed fan from the
chassis.

3. Replace the failed fan with an identical 4-cm, 12 volt fan (available from
Supermicro: p/n FAN-0086L4).

4. Push the new fan into the vacant space in the housing while making sure the
arrows on the top of the fan (indicating air direction) point in the same direc­tion as the arrows on the other fans.

5. Reposition the fan housing back over the two mounting posts in the chassis,
then reconnect the fan wires to the same chassis fan headers you removed
them from.

6. Power up the system and check that the fan is working properly and that the
LED on the control panel has turned off.

7. Finish by replacing the chassis cover.

6-3

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Figure 6-2. System Cooling Fans

Accessing the Drive Bays

Hard Drives: Because of their hotswap capability, you do not need to access the
inside of the chassis or power down the system to install or replace the SAS/SATA
drives. Proceed to the next section for instructions.

DVD-ROM Drive: For installing/removing a DVD-ROM drive, you will need to gain
access to the inside of the 6017R-N3RF4+/6017R-N3RFT+ by removing the top
cover of the chassis. Proceed to the "DVD-ROM Drive Installation" section later in
this chapter for instructions.

Note: Only a "slim" DVD-ROM drive will fi t into the 6017R-N3RF4+/6017R-N3RFT+.

Warning: Enterprise level hard disk drives are recommended for use in Supermicro

chassis and servers. For information on recommended HDDs, visit the Supermicro
Web site at http://www.supermicro.com/products/nfo/storage.cfm

6-4

Chapter 6: Advanced Chassis Setup

Hard Drive Installation

The hard drives are mounted in drive carriers to simplify their installation and
removal from the chassis. System power may remain on when removing carriers
with drives installed. These carriers also help promote proper airfl ow for the drive
bays. For this reason, even empty carriers without drives installed must remain in
the chassis.

Mounting a Hard Drive in a Drive Carrier

1. Insert a drive into the carrier with the printed circuit board side facing down so
that the mounting holes align with those in the carrier.

2. Secure the drive to the carrier with six screws, as shown in Figure 6-3.

Figure 6-3. Mounting a Drive in a Carrier

Warning: Use caution when working around the hard drive backplane. Do not touch the

backplane with any metal objects and make sure no ribbon cables touch the backplane
or obstruct the holes, which aid in proper airfl ow.

Warning: Regardless of how many hard drives are installed, all drive carriers must
remain in the drive bays to maintain proper airfl ow.

6-5

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Installing/Removing a Hard Drive

1. To remove a carrier, push the release button located beside the drive LEDs.

2. Swing the colored handle fully out and use it to pull the unit straight out (see
Figure 6-4).

Note: Your operating system must have RAID support to enable the hot-plug ca­pability of the hard drives.

Release tab

Figure 6-4. Removing a Drive from the Server

Hard Drive Backplane

The hard drives plug into a backplane that provides power and drive ID. A RAID
controller can be used with the backplane to provide data security. The operating
system you use must have RAID support to enable the hot-swap capability of the
drives. The backplane is already preconfi gured, so there are no jumpers or switches
present on it.

6-6

Chapter 6: Advanced Chassis Setup

DVD-ROM Drive Installation

The top cover of the chassis must be opened to gain full access to the DVD-ROM
drive bay. The 6017R-N3RF4+/6017R-N3RFT+ accomodates only slim DVD-ROM
drives. Side mounting brackets are needed to mount a slim DVD-ROM drive in the
server. You must power down the system before installing or removing a DVD­ROM drive.

Removing the Chassis Cover

1. Grasp the two handles on either side and pull the unit straight out until it
locks (you will hear a "click").

2. Depress the two buttons on the top of the chassis to release the top cover
and at the same time, push the cover away from you until it stops. You can
then lift the top cover from the chassis to gain full access to the inside of the
server.

Removing/Installing a Drive

1. With the chassis cover removed, unplug the power and data cables from the
drive you want to remove.

2. Locate the locking tab at the rear of the drive. It will be on the left side of the
drive when viewed from the front of the chassis.

3. Pull the tab away from the drive and push the drive unit out the front of the
chassis.

4. Add a new drive by following this procedure in reverse order. You may hear a
faint *click* of the locking tab when the drive is fully inserted.

5. Remember to reconnect the data and power cables to the drive before replac­ing the chassis cover and restoring power to the system.

6-7

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

6-4 Power Supply

The SuperServer 6017R-N3RF4+/6017R-N3RFT+ has a 700 watt redundant power
supply consisting of two power modules. Each power supply module has an auto­switching capability, which enables it to automatically sense and operate at a 100V

- 240V input voltage.

Power Supply Failure

If either of the two power supply modules fail, the other module will take the full load
and allow the system to continue operation without interruption. The PWR Fail LED
will illuminate and remain on until the failed unit has been replaced. Replacement
units can be ordered directly from Supermicro (part number PWS-703-P-1R). The
power supply units have a hot-swap capability, meaning you can replace the failed
unit without powering down the system.

Removing the Power Supply

First unplug the AC power cord from the failed power supply module.

1. Depress the locking tab on the power supply module.

2. Use the handle to pull it straight out with the rounded handle (see Fig. 6-5).

Installing a New Power Supply

1. Replace the failed hot-swap unit with another identical power supply unit.

2. Push the new power supply unit into the power bay until you hear a click.

3. Secure the locking tab on the unit.

4. Finish by plugging the AC power cord back into the unit.

6-8

Chapter 6: Advanced Chassis Setup

Figure 6-5. Removing/Replacing the Power Supply

2

1

6-9

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Notes

6-10

Chapter 7: BIOS

Chapter 7

BIOS

7-1 Introduction

This chapter describes the AMI BIOS Setup utility for the X9DRW-3LN4F+/X9DRW­3LN4T+. It also provides the instructions on how to navigate the AMI BIOS Setup

utility screens. The AMI ROM BIOS is stored in a Flash EEPROM and can be
easily updated.

Starting BIOS Setup Utility

To enter the AMI BIOS Setup utility screens, press the <Del> key while the system
is booting up.

Note: In most cases, the <Del> key is used to invoke the AMI BIOS setup
screen. There are a few cases when other keys are used, such as <F3>,
<F4>, etc.

Each main BIOS menu option is described in this manual. The Main BIOS setup
menu screen has two main frames. The left frame displays all the options that can
be confi gured. Grayed-out options cannot be confi gured. Options in blue can be
confi gured by the user. The right frame displays the key legend. Above the key
legend is an area reserved for a text message. When an option is selected in the
left frame, it is highlighted in white. Often a text message will accompany it.

Note: The AMI BIOS has default text messages built in. The manufacturer
retains the option to include, omit, or change any of these text mes­sages.

The AMI BIOS Setup utility uses a key-based navigation system called "hot keys."
Most of the AMI BIOS setup utility "hot keys" can be used at any time during setup
navigation. These keys include <F3>, <F4>, <Enter>, <ESC>, arrow keys, etc.

Note 1: Options printed in Bold are default settings.

Note 2: <F3> is used to load optimal default settings. <F4> is used to save

the settings and exit the setup utility.

7-1

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

How To Change the Confi guration Data

The confi guration data that determines the system parameters may be changed by
entering the AMI BIOS Setup utility. This Setup utility can be accessed by pressing
<F2> at the appropriate time during system boot.

Note: For AMI UEFI BIOS Recovery, please refer to the UEFI BIOS Re­covery User Guide posted @http://www.supermicro.com/support/manuals/.

Starting the Setup Utility

Normally, the only visible Power-On Self-Test (POST) routine is the memory test.
As the memory is being tested, press the <F2> key to enter the main menu of
the AMI BIOS Setup utility. From the main menu, you can access the other setup
screens. An AMI BIOS identifi cation string is displayed at the left bottom corner of
the screen below the copyright message.

Warning! Do not upgrade the BIOS unless your system has a BIOS-related issue.
Flashing the wrong BIOS can cause irreparable damage to the system. In no event
shall the manufacturer be liable for direct, indirect, special, incidental, or consequential
damage arising from a BIOS update. If you have to update the BIOS, do not shut down
or reset the system while the BIOS is being updated to avoid possible boot failure.

7-2 Main Setup

When you fi rst enter the AMI BIOS Setup utility, you will enter the Main setup screen.
You can always return to the Main setup screen by selecting the Main tab on the
top of the screen. The Main BIOS Setup screen is shown below.

The AMI BIOS main menu displays the following information:

7-2

Chapter 7: BIOS

System Date

This item displays the system date in Day MM/DD/YY format (e.g. Wed 10/12/2011).

System Time

This item displays the system time in HH:MM:SS format (e.g. 15:32:52).

Supermicro X9DRW-3LN4F+/X9DRW-3TF+

Version

This item displays the SMC version of the BIOS ROM used in this system.

Build Date

This item displays the date that the BIOS Setup utility was built.

Memory Information

Total Memory

This displays the amount of memory that is available in the system.

7-3 Advanced Setup Confi gurations

Use the arrow keys to select Advanced and press <Enter> to access the following
submenu items.

7-3

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Boot Features

Quiet Boot

This feature allows the user to select bootup screen display between POST mes­sages and the OEM logo. Select Disabled to display the POST messages. Select
Enabled to display the OEM logo instead of the normal POST messages. The op­tions are Enabled and Disabled.

AddOn ROM Display Mode

Use this item to set the display mode for the Option ROM. Select Keep Current to
use the current AddOn ROM Display setting. Select Force BIOS to use the Option
ROM display mode set by the system BIOS. The options are Force BIOS and
Keep Current.

Bootup Num-Lock

Use this feature to set the Power-on state for the Numlock key. The options are
Off and On.

Wait For 'F1' If Error

Select Enabled to force the system to wait until the 'F1' key is pressed if an error
occurs. The options are Disabled and Enabled.

Interrupt 19 Capture

Interrupt 19 is the software interrupt that handles the boot disk function. When this
item is set to Enabled, the ROM BIOS of the host adaptors will "capture" Interrupt 19
at bootup and allow the drives that are attached to these host adaptors to function
as bootable disks. If this item is set to Disabled, the ROM BIOS of the host adap­tors will not capture Interrupt 19, and the drives attached to these adaptors will not
function as bootable devices. The options are Enabled and Disabled.

Power Confi guration

Watch Dog Function

If enabled, the Watch Dog timer will allow the system to reboot when it is inactive
for more than 5 minutes. The options are Enabled and Disabled.

Power Button Function

If this feature is set to Instant Off, the system will power off immediately as soon
as the user presses the power button. If this feature is set to 4 Seconds Override,
the system will power off when the user presses the power button for 4 seconds or
longer. The options are Instant Off and 4 Seconds Override.

7-4

Chapter 7: BIOS

Restore on AC Power Loss

Use this feature to set the power state after a power outage. Select Stay Off for the
system power to remain off after a power loss. Select Power On for the system
power to be turned on after a power loss. Select Last State to allow the system
to resume its last state before a power loss. The options are Power On, Stay Off,
and Last State.

CPU Confi guration

This submenu displays the information of the CPU as detected by the BIOS. It also
allows the user to confi guration CPU settings.

Socket 1 CPU Information/Socket 2 CPU Information

This submenu displays the following information regarding the CPUs installed
in Socket 1/ Socket 2.

• Type of CPU

• CPU Signature

• Microcode Patch

• CPU Stepping

• Maximum CPU Speed

• Minimum CPU Speed

• Processor Cores

• Intel HT (Hyper-Threading) Technology

• Intel VT-x Technology

• Intel SMX Technology

• L1 Data Cache

• L1 Code Cache

• L2 Cache

• L3 Cache

7-5

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

CPU Speed
This item displays the speed of the CPU installed in Socket 1/Socket 2.

64-bit
This item indicates if the CPU installed in Socket 1 or Socket 2 supports 64-bit

technology.

Clock Spread Spectrum

Select Enable to enable Clock Spectrum support, which will allow the BIOS to moni­tor and attempt to reduce the level of Electromagnetic Interference caused by the
components whenever needed. The options are Disabled and Enabled.

RTID (Record Types IDs)

This feature displays the total number of Record Type IDs for local and remote
pools. The options are Optimal and Alternate.

Hyper-threading

Select Enabled to support Intel Hyper-threading Technology to enhance CPU per­formance. The options are Enabled and Disabled.

Active Processor Cores

Set to Enabled to use a processor's second core and above. (Please refer to Intel's
website for more information.) The options are All, 1, 2, 4 and 6.

Limit CPUID Maximum

This feature allows the user to set the maximum CPU ID value. Enable this function
to boot the legacy operating systems that cannot support processors with extended
CPUID functions. The options are Enabled and Disabled (for the Windows OS).

Execute-Disable Bit (Available if supported by the OS & the CPU)

Select Enabled to enable the Execute Disable Bit which will allow the processor
to designate areas in the system memory where an application code can execute
and where it cannot, thus preventing a worm or a virus from fl ooding illegal codes
to overwhelm the processor or damage the system during an attack. The default is

Enabled. (Refer to Intel and Microsoft Web sites for more information.)

Intel® AES-NI

Select Enable to use the Intel Advanced Encryption Standard (AES) New Instruc­tions (NI) to ensure data security. The options are Enabled and Disabled.

7-6

Chapter 7: BIOS

MLC Streamer Prefetcher (Available when supported by the CPU)

If set to Enabled, the MLC (mid-level cache) streamer prefetcher will prefetch
streams of data and instructions from the main memory to the L2 cache to improve
CPU performance. The options are Disabled and Enabled.

MLC Spatial Prefetch (Available when supported by the CPU)

If this feature is set to Disabled, The CPU prefetches the cache line for 64 bytes.
If this feature is set to Enabled the CPU fetches both cache lines for 128 bytes as
comprised. The options are Disabled and Enabled.

DCU Streamer Prefetcher (Available when supported by the CPU)

Select Enabled to support Data Cache Unite (DCU) prefetch of L1 data to speed
up data accessing and processing in the DCU to enhance CPU performance. The
options are Disabled and Enabled.

DCU IP Prefetcher

Select Enabled for DCU (Data Cache Unit) IP Prefetcher support, which will prefetch
IP addresses to improve network connectivity and system performance. The options
are Enabled and Disabled.

Intel® Virtualization Technology (Available when supported by the CPU)

Select Enabled to support Intel Virtualization Technology, which will allow one
platform to run multiple operating systems and applications in independent parti­tions, creating multiple "virtual" systems in one physical computer. The options
are Enabled and Disabled.

Note: If there is any change to this setting, you will need to power off and
restart the system for the change to take effect. Please refer to Intel’s
website for detailed information.)

 CPU Power Management Confi guration

This submenu allows the user to confi gure the following CPU Power Management
settings.

Power Technology

Select Energy Effi ciency to support power-saving mode. Select Custom to cus-
tomize system power settings. Select Disabled to disable power-saving settings.
The options are Disabled, Energy Effi ciency, and Custom. If the option is set
to Custom, the following items will display:

7-7

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

EIST (Available when Power Technology is set to Custom)

EIST (Enhanced Intel SpeedStep Technology) allows the system to au­tomatically adjust processor voltage and core frequency to reduce power
consumption and heat dissipation. The options are Disabled (GV3 Disabled),
and Enabled (GV3 Enabled). (Note: GV3 is Intel Speedstep support used
on older platforms. Please refer to Intel’s website for detailed information.)

Turbo Mode (Available when Power Technology is set to Custom)

Select Enabled to use the Turbo Mode to boost system performance. The
options are Enabled and Disabled.

C1E (Available when Power Technology is set to Custom)

Select Enabled to enable Enhanced C1 Power State to boost system per­formance. The options are Enabled and Disabled.

CPU C3 Report (Available when Power Technology is set to Custom)

Select Enabled to allow the BIOS to report the CPU C3 State (ACPI C2) to
the operating system. During the CPU C3 State, the CPU clock generator
is turned off. The options are Enabled and Disabled.

CPU C6 Report (Available when Power Technology is set to Custom)

Select Enabled to allow the BIOS to report the CPU C6 State (ACPI C3) to
the operating system. During the CPU C6 State, the power to all cache is
turned off. The options are Enabled and Disabled.

CPU C7 Report (Available when Power Technology is set to Custom)

Select Enabled to allow the BIOS to report the CPU C7 State (ACPI C3) to
the operating system. CPU C7 State is a processor-specifi c low C-State.
The options are Enabled and Disabled.

Package C-State limit (Available when Power Technology is set to
Custom)

This feature allows the user to set the limit on the C-State package register.
The options are C0, C2, C6, and No Limit.

Energy Performance Bias

This setting allows the user to adjust the fan speed based on performance (maxi­mum cooling) or energy effi ciency (maximum energy savings). The options are
Performance, Balanced Performance, Balanced Energy, and Energy Effi cient.

7-8

Chapter 7: BIOS

Factory Long Duration Power Limit

This item displays the power limit set by the manufacturer during which long
duration power is maintained.

Long Duration Power Limit

This item displays the power limit set by the user during which long duration
power is maintained.

Factory Long Duration Maintained (Available when Power Technology is
set to Custom)

This item displays the period of time set by the manufacturer during which long
duration power is maintained.

Long Duration Maintained

This item displays the period of time during which long duration power is main­tained.

Recommended Short Duration Power

This item displays the short duration power settings recommended by the
manufacturer.

Short Duration Power Limit

This item displays the time period during which short duration power is main­tained.

Chipset Confi guration

North Bridge

This feature allows the user to confi gure the settings for the Intel North Bridge.

Integrated IO Confi guration

Intel VT-d

Select Enabled to enable Intel Virtualization Technology support for Direct I/O
VT-d

by reporting the I/O device assignments to the VWM (Virtual Working

Memory) through the DMAR ACPI Tables. This feature offers fully-protected
I/O resource sharing across Intel platforms, providing greater reliability, security
and availability in networking and data-sharing. The options are Enabled and
Disabled.

7-9

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Data Direct I/O

Select Enabled to enable Intel I/OAT (I/O Acceleration Technology), which sig­nifi cantly reduces CPU overhead by leveraging CPU architectural improvements
and freeing the system resource for other tasks. The options are Disabled and

Enabled.

DCA Support

Select Enabled to use Intel's DCA (Direct Cache Access) Technology to improve
data transfer effi ciency. The options are Enabled and Disabled.

IIO 1 PCIe Port Bifurcation Control

This submenu confi gures the following IO PCIe Port Bifurcation Control settings
for IIO 1 PCIe ports to determine how the available PCI-Express lanes to be
distributed between the PCI-Exp. Root Ports.

IOU2-PCIe Port

This feature allows the user to set the bus speed between the IOU2 and the
PCI-Exp port. The options are x4x4x4x4, x4x4x8, x8x4x4, x8x8, x16, Auto.

IOU3-PCIe Port

This feature allows the user to set the bus speed between the IOU3 and the
PCI-Exp port. The options are x4x4x4x4, x4x4x8, x8x4x4, x8x8, x16, and Auto.

IIO 2 PCIe Port Bifurcation Control

This submenu confi gures the following IO PCIe Port Bifurcation Control settings
for IIO 2 PCIe ports to determine how the available PCI-Express lanes to be
distributed between the PCI-Exp. Root Ports.

IOU2-PCIe Port

This feature allows the user to set the bus speed between the IOU2 and the
PCI-Exp port. The options are x4x4x4x4, x4x4x8, x8x4x4, x8x8, x16, Auto.

IOU3-PCIe Port

This feature allows the user to set the bus speed between the IOU3 and the
PCI-Exp port. The options are x4x4x4x4, x4x4x8, x8x4x4, x8x8, x16, and Auto.

QPI Confi guration

Current QPI Link

This item displays the current status of the QPI Link.

7-10

Chapter 7: BIOS

Current QPI Frequency

This item displays the frequency of the QPI Link.

Isoc

Select Enabled to enable Ischronous support to meet QoS (Quality of Service)
requirements. This feature is especially important for virtualization technology.
The options are Enabled and Disabled.

QPI (Quick Path Interconnect) Link Speed Mode

Use this feature to select data transfer speed for QPI Link connections. The
options are Fast and Slow.

QPI Link Frequency Select

Use this feature to select the desired QPI frequency. The options are Auto, 6.4
GT/s, 7.2 GT/s, and 8.0 GT/s.

DIMM Confi guration

This section displays the following DIMM information.

Current Memory Mode

This item displays the current memory mode.

Current Memory Speed

This item displays the current memory speed.

Mirroring

This item displays if memory mirroring is supported by the motherboard. Memory
mirroring creates a duplicate copy of the data stored in the memory to enhance
data security.

Sparing

This item displays if memory sparing is supported by the motherboard. Memory
sparing enhances system performance.

DIMM Information

CPU Socket 1 DIMM Information/ CPU Socket 2 DIMM Information

The status of the memory modules detected by the BIOS will be displayed as
detected by the BIOS.

7-11

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

Memory Mode

When Independent is selected, all DIMMs are available to the operating system.
When Mirroring is selected, the motherboard maintains two identical copies of all
data in memory for data backup. When Lockstep is selected, the motherboard
uses two areas of memory to run the same set of operations in parallel. The
options are Independent, Mirroring, and Lockstep.

DRAM RAPL Mode

RAPL (Running Average Power Limit) provides mechanisms to enforce power
consumption limits on supported processors The options are DRAM RAPL
MODE0 , DRAM RAPL MODE1, and Disabled.

DDR Speed

Use this feature to force a DDR3 memory module to run at a frequency other
than what is specifi ed in the specifi cation. The options are Auto, Force DDR3-
800, Force DDR3-1066, Force DDR3-1333, Force DDR3-1600 and Force SPD.

Channel Interleaving

This feature selects from the different channel interleaving methods. The options
are Auto, 1 Way, 2 Way, 3, Way, and 4 Way.

Rank Interleaving

This feature allows the user to select a rank memory interleaving method. The
options are Auto, 1 Way, 2 Way, 4, Way, and 8 Way.

Patrol Scrub

Patrol Scrubbing is a process that allows the CPU to correct correctable memory
errors detected on a memory module and send the correction to the requestor
(the original source). When this item is set to Enabled, the IO hub will read and
write back one cache line every 16K cycles, if there is no delay caused by internal
processing. By using this method, roughly 64 GB of memory behind the IO hub
will be scrubbed every day. The options are Enabled and Disabled.

Demand Scrub

Demand Scrubbing is a process that allows the CPU to correct correctable
memory errors found on a memory module. When the CPU or I/O issues a
demand-read command, and the read data from memory turns out to be a
correctable error, the error is corrected and sent to the requestor (the original
source). Memory is updated as well. Select Enabled to use Demand Scrubbing
for ECC memory correction. The options are Enabled and Disabled.

7-12

Chapter 7: BIOS

Data Scrambling

Select Enabled to enable data scrambling to ensure data security and integrity.
The options are Disabled and Enabled.

Device Tagging

Select Enabled to support device tagging. The options are Disabled and En­abled.

Thermal Throttling

Throttling improves reliability and reduces power consumption in the proces­sor via automatic voltage control during processor idle states. The options are
Disabled and CLTT (Closed Loop Thermal Throttling).

South Bridge Confi guration

This feature allows the user to confi gure the settings for the Intel PCH chip.

PCH Information

This feature displays the following PCH information.

Name: This item displays the name of the PCH chip.

Stepping: This item displays the status of the PCH stepping.

USB Devices: This item displays the USB devices detected by the BIOS.

All USB Devices

This feature enables all USB ports/devices. The options are Disabled and Enabled.
(If set to Enabled, EHCI Controller 1 and Controller 2 will appear.)

EHCI Controller 1/EHCI Controller 2 (Available when All USB Devices is set
to Enabled)

Select Enabled to enable EHCI (Enhanced Host Controller Interface) Controller 1
or Controller 2. The options are Disabled and Enabled.

Legacy USB Support (Available when USB Functions is not Disabled)

Select Enabled to support legacy USB devices. Select Auto to disable legacy sup­port if USB devices are not present. Select Disable to have USB devices available

7-13

SUPERSERVER 6017R-N3RF4+/6017R-N3RFT+ User's Manual

for EFI (Extensive Firmware Interface) applications only. The settings are Disabled,

Enabled and Auto.

Port 60/64 Emulation

Select Enabled to enable I/O port 60h/64h emulation support for the legacy USB
keyboard so that it can be fully supported by the operating systems that does not
recognize a USB device. The options are Disabled and Enabled.

EHCI Hand-Off

This item is for operating systems that do not support Enhanced Host Controller
Interface (EHCI) hand-off. When enabled, EHCI ownership change will be claimed
by the EHCI driver. The options are Disabled and Enabled.

SATA Confi guration

When this submenu is selected, the AMI BIOS automatically detects the presence
of IDE or SATA devices and displays the following items.

SATA Port0~SATA Port5: The AMI BIOS displays the status of each SATA port
as detected by the BIOS.

SATA Mode

Use this feature to confi gure SATA mode for a selected SATA port. The options are
Disabled, IDE Mode, AHCI Mode and RAID Mode. The following are displayed
depending on your selection:

IDE Mode

The following items are displayed when IDE Mode is selected:

Serial-ATA (SATA) Controller 0~1

Use this feature to activate or deactivate the SATA controller, and set the
compatibility mode. The options are Disabled, Enhanced, and Compatible.
The default for Controller 0 is Compatible. The default of SATA Controller
1 is Enhanced.

7-14