Supero 6017R-73THDP+, Supero 6017R-73HDP+, SUPERSERVER 6017R-73THDP+, SUPERSERVER 6017R-73HDP+ User Manual

SUPER

SUPERSERVER

6017R-73THDP+

6017R-73HDP+

®

USER’S MANUAL

1.0

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu­mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTW ARE, OR DA TA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environ­ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the manufacturer’s instruction manual, may cause harmful interference
with radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case you will be required to correct the interference at your own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn­ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to the
State of California to cause birth defects and other repro­ductive harm.

Manual Revision 1.0
Release Date: May 29, 2013

Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.

Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2013 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

Preface

About This Manual

This manual is written for professional system integrators and PC technicians.
It provides information for the installation and use of the SuperServer 6017R­73THDP+/6017R-73HDP+. Installation and maintenance should be performed by
experienced technicians only.

Manual Organization

Chapter 1: Introduction

The fi rst chapter provides a checklist of the main components included with the
server system and describes the main features of the serverboard and the chassis.

Preface

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer into a rack and
check out the server confi guration prior to powering up the system. If your server
was ordered without processor and memory components, this chapter will refer you
to the appropriate sections of the manual for their installation.

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.

Chapter 4: Standardized Warning Statements

You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 6017R-73THDP+/6017R-73HDP+.

Chapter 5: Advanced Serverboard Setup

Chapter 5 provides detailed information on the X9DRFF-7TG+/X9DRFF-7G+
serverboard, including the locations and functions of connections, headers and
jumpers. Refer to this chapter when adding or removing processors or main memory
and when reconfi guring the serverboard.

iii

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the SC816LTS-655B server chassis.
You should follow the procedures given in this chapter when installing, removing
or reconfi guring SAS or peripheral drives and when replacing system power supply
modules and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed informa­tion on running the CMOS Setup Utility.

Appendix A: BIOS Error Beep Codes

Appendix B: System Specifi cations

iv

Notes

Preface

v

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Table of Contents

Chapter 1 Introduction

1-1 Overview .........................................................................................................1-1

1-2 Serverboard Features .....................................................................................1-2

Processors ......................................................................................................1-2

Memory ...........................................................................................................1-2

Onboard SAS .................................................................................................. 1-2

Onboard Serial ATA ........................................................................................ 1-2

Rear I/O Ports ................................................................................................. 1-2

Graphics Controller .........................................................................................1-2

1-3 Server Chassis Features ................................................................................1-3

System Power ................................................................................................. 1-3

Hard Drives .....................................................................................................1-3

PCI Expansion Slots ....................................................................................... 1-3

Front Control Panel .........................................................................................1-3

Cooling System ............................................................................................... 1-3

1-4 Contacting Supermicro ....................................................................................1-5

Chapter 2 Server Installation

2-1 Overview .........................................................................................................2-1

2-2 Unpacking the System .................................................................................... 2-1

2-3 Preparing for Setup .........................................................................................2-1

Choosing a Setup Location ............................................................................. 2-1

2-4 Warnings and Precautions .............................................................................. 2-2

Rack Precautions ............................................................................................ 2-2

Server Precautions .......................................................................................... 2-2

Rack Mounting Considerations .......................................................................2-3

Ambient Operating Temperature ................................................................ 2-3

Reduced Airfl ow .........................................................................................2-3

Mechanical Loading ................................................................................... 2-3

Circuit Overloading .....................................................................................2-3

Reliable Ground ......................................................................................... 2-3

2-5 Rack Mounting Instructions ............................................................................. 2-4

Identifying the Inner Rail and Inner Rail Extension ........................................2-4

Locking Tabs ...................................................................................................2-4

Attaching the Inner Rail .................................................................................. 2-5

Installing the Outer Rails to the Rack ............................................................. 2-6

Chassis Installation .........................................................................................2-8

vi

Table of Contents

Chapter 3 System Interface

3-1 Overview .........................................................................................................3-1

3-2 Control Panel Button .......................................................................................3-1

Power ..............................................................................................................3-1

Chapter 4 Standardized Warning Statements for AC Systems

4-1 About Standardized Warning Statements .......................................................4-1

Warning Defi nition ...........................................................................................4-1

Installation Instructions .................................................................................... 4-4

Circuit Breaker ................................................................................................ 4-5

Power Disconnection Warning ........................................................................ 4-6

Equipment Installation .....................................................................................4-8

Restricted Area ................................................................................................4-9

Battery Handling ............................................................................................ 4-10

Redundant Power Supplies ..........................................................................4-12

Backplane Voltage ........................................................................................ 4-13

Comply with Local and National Electrical Codes ........................................ 4-14

Product Disposal ........................................................................................... 4-15

Hot Swap Fan Warning ................................................................................. 4-16

Power Cable and AC Adapter ......................................................................4-18

Chapter 5 Advanced Serverboard Setup

5-1 Handling the Serverboard ............................................................................... 5-1

Precautions .....................................................................................................5-1

Unpacking .......................................................................................................5-1

5-2 Installing the Processor and Heatsink ............................................................ 5-2

Installing an LGA2011 Processor .................................................................... 5-2

Installing a CPU Heatsink ............................................................................... 5-5

Removing the Heatsink ................................................................................... 5-5

5-3 Connecting Cables .......................................................................................... 5-6

Connecting Data Cables ................................................................................. 5-6

Connecting Power Cables ..............................................................................5-6

5-4 I/O Ports ..........................................................................................................5-6

5-5 Installing Memory ............................................................................................ 5-7

5-6 Adding PCI Cards ......................................................................................... 5-10

5-7 Serverboard Details .......................................................................................5-11

X9DRFF-7TG+/X9DRFF-7G+ Quick Reference ...........................................5-12

5-8 Connector Defi nitions ....................................................................................5-13

5-9 Jumper Settings ............................................................................................5-16

5-10 Onboard Indicators ........................................................................................5-18

vii

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

5-11 SAS/SATA Port Connections ......................................................................... 5-19

5-12 Installing Software ......................................................................................... 5-20

SuperDoctor III .............................................................................................. 5-21

5-13 Onboard Battery ............................................................................................ 5-22

Chapter 6 Advanced Chassis Setup

6-1 Static-Sensitive Devices ..................................................................................6-1

Precautions .....................................................................................................6-1

Unpacking .......................................................................................................6-1

6-2 Removing the Covers .....................................................................................6-2

6-3 System Fans ...................................................................................................6-3

6-4 Drive Bay Installation/Removal .......................................................................6-5

Replacing Hard Drives .................................................................................... 6-5

6-5 Installing Expansion Cards .............................................................................6-7

6-6 Replacing the Power Supply ........................................................................... 6-8

Power Supply Replacement ............................................................................ 6-8

Chapter 7 BIOS

7-1 Introduction ...................................................................................................... 7-1

Starting BIOS Setup Utility .............................................................................. 7-1

How To Change the Confi guration Data .........................................................7-2

Starting the Setup Utility ................................................................................. 7-2

7-2 Main Setup ...................................................................................................... 7-2

7-3 Advanced Setup Confi gurations......................................................................7-4

7-4 Event Logs .................................................................................................... 7-23

7-5 IPMI ............................................................................................................... 7-25

7-6 Boot ............................................................................................................... 7-27

7-7 Secur it y ......................................................................................................... 7-28

7-8 Save & Exit ................................................................................................... 7-29

Appendix A BIOS Error Beep Codes
Appendix B System Specifi cations

viii

Chapter 1: Introduction

Chapter 1

Introduction

1-1 Overview

The SuperServer 6017R-73THDP+/6017R-73HDP+ is a high-end server comprised
of two main subsystems: the SC816LTS-655B 1U server chassis and the X9DRFF­7TG+/X9DRFF-7G+ dual processor serverboard. Please refer to our web site for
information on operating systems that have been certifi ed for use with the system
(www.supermicro.com).

In addition to the serverboard and chassis, various hardware components have been
included with the 6017R-73THDP+/6017R-73HDP+, as listed below:

• Four 4-cm fans (FAN-0065L4)

• Four 4-cm fans (FAN-0088L4)

• One air shroud (MCP-310-19012-0N)

• Two passive CPU heatsinks (SNK-P0047PS)

• Riser Card: (see Section 5-6 for details)

One RSC-R1UFF-E8R

• SAS/SATA Accessories

Three backplanes (BPN-SAS-816T-A2, BPN-SAS-816T -A4, BPN-SAS-816T -A6)

• One rackmount kit (MCP-290-00102-0N)

1-1

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

1-2 Serverboard Features

At the heart of the SuperServer 6017R-73THDP+/6017R-73HDP+ lies the X9DRFF­7TG+/X9DRFF-7G+, a dual processor serverboard based on the Intel® C602
chipset. Below are the main features of the serverboard. (See Figure 1-1 for a
block diagram of the chipset.)

Processors

The X9DRFF-7TG+/X9DRFF-7G+ supports single or dual Intel® E5-2600 Series
processors in LGA2011 sockets. Please refer to our web site for a complete listing
of supported processors (www.supermicro.com).

Memory

The X9DRFF-7TG+/X9DRFF-7G+ has 16 memory sockets that can support up to
512 GB of ECC registered DDR3-1600/1333/1066/800 RDIMMs or up to 128 GB
of unbuffered ECC/non-ECC DDR3-1600/1333/1066/800 UDIMMs. Please refer to
Chapter 5 for installing memory.

Onboard SAS

An LSI 23 08 SAS controller provides eight SAS2 ports. The SAS drives are con­nected to a backplane that provides power, bus termination and confi guration set-
tings. RA ID 0, 1 and 10 are su ppor ted.

Onboard Serial ATA

A SATA controller is integrated into the chipset to provide a six-port SATA subsys­tem. Two of the port s suppo r t SATA 3 .0 and fou r suppo r t SATA 2. 0 (see Chapter
5 for detai ls). RAI D 0, 1, 5 and 10 are suppor ted.

I/O Ports

The color-coded I/O ports located at the front of the server include a VGA (moni­tor) port, two USB 2.0 ports, two 1 Gb Ethernet ports (the X9DRFF-7TG+/6017R­73THDP+ features two 10 Gb Ethernet ports) and one dedicated IPMI LAN port.

Graphics Controller

The X9DRFF-7TG+/X9DRFF-7G+ features an integrated Matrox G200ew, 16 MB
DDR2 graphics controller.

1-2

Chapter 1: Introduction

1-3 Server Chassis Features

The 6017R-73THDP+/6017R-73HDP+ is built upon the SC816LTS-655B chassis.
Details on the chassis and on servicing procedures can be found in Chapter 6. The
following is a general outline of the main features of the chassis.

System Power

The SC816LTS-655B features a single 650W power supply consisting of a single
power module. The system must be shut down when replacing or removing this
power supply module.

Hard Drives

The SC816LTS-655B chassis was des igned to supp ort 12 SAS/SATA fi xed hard
drives, w hich a re mounted i nside t he chas sis.

PCI Expansion Slots

One riser card is included with the system. The RSC-R1UFF-E8R supports one
standard size PCI-E 3.0 x8 add-on card. See our web site for details (http://www.
supermicro.com/products/nfo/UIO.cfm) and section 5-6 of this manual for details.

Front Control Panel

The chassis' control panel includes a single system power-on button, which also
functions as a UID indicator.

Cooling System

The SC816LTS-655B has an innovative cooling design that features four 4-cm
counter-rotating fans located in the middle section of the chassis and four 4-cm
exhaust fans. The power supply module also includes a cooling fan.

1-3

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Figure 1-1. Intel C602 Chipset:

System Block Diagram

Note: This is a general block diagram. Please see Chapter 5 for details.

Gen3 x16 x16

SAS2 #1
SAS2 #2
SAS2 #3
SAS2 #4
SAS2 #5
SAS2 #6
SAS2 #7
SAS2 #8

SAS

RJ45

RJ45

PCI-Ex16x16

Proprietary SLOT

SAS2308

I350 (2 ports)

J1

PCI-Ex16

Proprietary SLOT

LAN

X540

J2

Gen3 x8

#1

#2

E

DDR3 DIMM

#1

#2

C

DDR3 DIMM

Gen3 x8 (0~7)

J3

J4

PCI-Ex8 SLOT

PCI-Ex8 SLOT

PCI-Ex4 in x8 SLOT

#1

#2

F

DDR3 DIMM

#1

#2

D

DDR3 DIMM

Gen3 x16

Gen3 x8 (8~15)

Gen3 x8 (0~7)

Gen2 x4

PE2

PE1 DMI

E5-2600 Series Processor

E5-2600 Series Processor

PE1

PE3

CPU1

Rear (Fan Side)

P0 P1

QPI

P1 P0

CPU0

Front (I/O Side)

PE2

PE3

QPI

DMI

Gen2 x4

DMI

PEG2_5:7

PEG2_0:4

DDR2

#1

#2

H

DDR3 DIMM

#1

#2

B

DDR3 DIMM

AT25321

SPI

PCH C602

WPCM450

VGA BMC

G

A

SATA

AHCI

LPCPCI-32bit

#1

#2

DDR3 DIMM

#1

#2

DDR3 DIMM

6/3/1.5
6/3/1.5

SCU

USB

3/1.5
3/1.5
3/1.5
3/1.5

SATA

USB

TPM

SATA2 #6
SATA2 #5
SATA2 #4
SATA2 #3
SATA3 #2
SATA3 #1

SATA2 #1 DOM

01 2

Single

Single

Type A

1-4

VGA CONN

PHY
RTL8201F

LAN

1-4 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)

Chapter 1: Introduction

Web Site:

Europe

Address: Super Micro Computer B.V.

Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

Asia-Pacifi c

Address: Super Micro Computer, Inc.

www.supermicro.com

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

[e-mail] (Technical Support)

[e-mail] (Customer Support)

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 23511

Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
Web Site:
Technical Support:
Email: [e-mail]
Tel: [phone]

www.supermicro.com.tw

1-5

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Notes

1-6

Chapter 2: Server Installation

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your SuperServer 6017R­73THDP+/6017R-73HDP+ up and running. Following the steps in the order given
should enable you to have the system operational within a minimal amount of time.
This quick setup assumes that your system has come to you with the processor and
memory preinstalled. If your system is not already fully integrated with a mother­board, processor, system memory etc., please turn to the chapter or section noted
in each step for details on installing specifi c components.

2-2 Unpacking the System

You should inspect the box the server was shipped in and note if it was damaged
in any way. If the server itself shows damage, you should fi le a damage claim with
the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the server. It should
be situated in a clean, dust-free area that is well ventilated. Avoid areas where
heat, electrical noise and electromagnetic fi elds are generated. You will also need
it placed near a grounded power outlet. Read the Rack and Server Precautions in
the next section.

2-3 Preparing for Setup

The box the SuperServer 6017R-73THDP+/6017R-73HDP+ was shipped in should
include two sets of rail assemblies, six rail mounting brackets and the mounting
screws you will need to install the system into the rack. Follow the steps in the
order given to complete the installation process in a minimal amount of time. Please
read this section in its entirety before you begin the installation procedure outlined
in the sections that follow.

Choosing a Setup Location

• Leave enough clearance in front of the rack to enable you to open the front door

completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for suffi cient airfl ow and ease in servicing.This product is for

2-1

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

installation only in a Restricted Access Location (dedicated equipment rooms,
service closets and the like).

• This product is not suitable for use with visual display work place devices

acccording to §2 of the the German Ordinance for Work with Visual Display
Units.

2-4 Warnings and Precautions

Rack Precautions

• Ensure that the leveling jacks on the bottom of the rack are fully extended to

the fl oor with the full weight of the rack resting on them.

• In single rack installation, stabilizers should be attached to the rack. In multiple

rack installations, the racks should be coupled together.

• Always make sure the rack is stable before extending a component from the

rack.

• You should extend only one component at a time - extending two or more si-

multaneously may cause the rack to become unstable.

Server Precautions

• Review the electrical and general safety precautions in Chapter 4.

• Determine the placement of each component in the rack before you install the

rails.

• Install the heaviest server components on the bottom of the rack fi rst, and then

work up.

• Use a regulating uninterruptible power supply (UPS) to protect the server from

power surges, voltage spikes and to keep your system operating in case of a
power failure.

• Allow the hot plug SATA drives and power supply modules to cool before touch-

ing them.

• Always keep the rack's front door and all panels and components on the servers

closed when not servicing to maintain proper cooling.

2-2

Chapter 2: Server Installation

Rack Mounting Considerations

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating tempera­ture of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient tempera­ture (Tmra).

Reduced Airfl ow

Equipment should be mounted into a rack so that the amount of airfl ow required
for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.

Circuit Overloading

Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connec­tions other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).

Warning! To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system remains
stable. The following guidelines are provided to ensure your safety:

• This unit should be mounted at the bottom of the rack if it is the only unit in

the rack.

• When mounting this unit in a partially fi lled rack, load the rack from the bottom

to the top with the heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before

mounting or servicing the unit in the rack.

2-3

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

2-5 Rack Mounting Instructions

This section provides information on installing the chassis into a rack unit with the
rails provided. There are a variety of rack units on the market, which may mean
that the assembly procedure will differ slightly from the instructions provided. You
should also refer to the installation instructions that came with the rack unit you are
using. NOTE: This rail will fi t a rack between 26.5" and 36.4" deep.

Identifying the Inner Rail and Inner Rail Extension

The SC816LT chassis includes mounting rails for installing the system into a rack.
Each assembly consists of two sections: An inner rail which is pre-installed on the
chassis, an inner rail extension, and an outer rail that secures to the rack. These
assemblies are specifi cally designed for the left and right side of the chassis

Locking Tabs

Each inner rail has a locking tab. This tab locks the chassis into place when installed
and pushed fully into the rack. These tabs also lock the chassis in place when fully
extended from the rack. This prevents the server from coming completely out of
the rack when when the chassis is pulled out for servicing.

Inner Rail

Extension

Inner Rail

Three

Screws

Three

Screws

Figure 2-1. Identifying the Inner Rails and Inner Rail Extensions

Locking Tab

2-4

Chapter 2: Server Installation

Attaching the Inner Rail

The SC816LT chassis ships with the inner rails already installed. In most cases it
is only necessary to install the inner rail extention.

Releasing Inner Rail from the Outer Rails

1. Identify the left and right inner rails and inner rail extensions as illustrated in
Figure 6-1.

2. Place the inner rail and inner rail extension against the side of the chassis.

3. Slide the inner rail and inner rail extension forward toward the front of the
chassis

4. Secure the inner rail and inner rail extension with three screws.

5. Repeat steps 1-4 with the remaining inner rail.

1

4

1

2

1

3

Figure 2-2. Attaching the Inner Rail and Inner Rail Extension

Warning: do not pick up the server with the front handles. They are de-

signed to pull the system from a rack only.

1

2

2-5

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Flat head

M5 x 12 mm [0.472]

Washer for M5

Secure to the

Rear of the Rack

Attach Outer Rack Rails

Together

Secure to the

Front of the Rack

Figure 2-3. Assembling the Outer Rails

Installing the Outer Rails to the Rack

Installing the Outer Rails

1. Attach the short bracket to the outside of the long bracket. You must align the
pins with the slides. Also, both bracket ends must face the same direction.

2-6

Chapter 2: Server Installation

Figure 2-4. Attaching the Outer Rails to a Rack

2. Adjust both the short and long brackets to the proper distance so that the rail
fi ts snugly into the rack.

3. Secure the long bracket to the front side of the outer rail with two M5 screws
and the short bracket to the rear side of the outer rail with three M5 screws.
Use a washer with each screw.

4. Repeat steps 1-4 for the remaining outer rail.

Stability hazard. The rack stabilizing mechanism must be in place, or the
rack must be bolted to the fl oor before you slide the unit out for servicing.
Failure to stabilize the rack can cause the rack to tip over.

2-7

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

1

3

Figure 2-5. Installing the Chassis into a Rack

Note: fi gures are for illustrative purposes only. Always install servers into racks

from the bottom up.

Chassis Installation

Installing the Chassis into a Rack

1. Confi rm that the rails are correctly installed on the rack.

2. Align the guides on the chassis with the front of the rails.

3. Slide the guides of the chassis into the rails, keeping the pressure even on
both sides, until the locking tabs click into place, securing chassis in a fully
extended position.

4. Simultaneously depress the locking tabs of both rails at the same time and
push the chassis all the way into the rack.

5. If necessary, use screws to secure the chassis handles to the front of the
rack.

2-8

Chapter 3: System Interface

Chapter 3

System Interface

3-1 Overview

The server chassis has a single power on/off button. No other buttons or indicators
are needed on the Hadoop server.

3-2 Control Panel Button

The power on/off button is located just to the right of the COM port on the front of
the chassis.

Power

The main power button is used to apply or remove power from the power supply to
the system. Turning off system power with this button removes the main power, but
keeps standby power supplied to the system. For this reason, you should unplug
the system before servicing. The power button has a built-in LED that will turn green
when the power is on.

3-1

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Notes

3-2

Chapter 4: Warning Statements for AC Systems

Chapter 4

Standardized Warning Statements for AC Systems

4-1 About Standardized Warning Statements

The following statements are industry standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions
or experience difficulty, contact Supermicro's Technical Support department
for assistance. Only certifi ed technicians should attempt to install or confi gure
components.

Read this appendix in its entirety before installing or confi guring components in the
Supermicro chassis.

These warnings may also be found on our web site at http://www.supermicro.com/
about/policies/safety_information.cfm.

Warning Defi nition

Warning!

This warning symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.

警告の定義

この警告サインは危険を意味します。

人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、

電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。

此警告符号代表危险。

您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前，必须充分
意识到触电的危险，并熟练掌握防止事故发生的标准工作程序。请根据每项警告结
尾的声明号码找到此设备的安全性警告说明的翻译文本。

此警告符號代表危險。

您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前，請注意觸
電的危險，並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號
碼找到相關的翻譯說明內容。

4-1

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

ןונקת תורהצהאהרהז

Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befi nden sich in einer Situation, die zu

Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den
Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung
vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen
Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes

de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y
familiarícese con los procedimientos estándar de prevención de accidentes. Al
fi nal de cada advertencia encontrará el número que le ayudará a encontrar el texto
traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES.

IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une

situation pouvant entraîner des blessures ou des dommages corporels. Avant
de travailler sur un équipement, soyez conscient des dangers liés aux circuits
électriques et familiarisez-vous avec les procédures couramment utilisées pour
éviter les accidents. Pour prendre connaissance des traductions des avertissements
fi gurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fi n de chaque avertissement.

CONSERVEZ CES INFORMATIONS.

ןה תואבה תורהצהא ינפמ שמתשמה תא ריהזהל תנמ לע ,היישעתה ינקת יפ לע תורהז הלבח

ה וא תולאש שיו הדימב .תירשפא תיזיפי ,יהשלכ היעבב תולקתרוציל שי הכימת תקלחמ םע רשק

רידגהל וא ןיקתהל םיאשר דבלב םיכמסומ םיאנכט .ורקימרפוס לש תינכט תאה .םיביכר

תרדגה וא תנקתה ינפל ואולמב חפסנה תא

אורקל שי .ורקימרפוס יזראמב םיביכרה

4-2

Warning Statements for AC Systems

. ﻲﻓ ﻚﻧﺍ ﻥﺃ ﻦﻜﻤﻳ ﺔﻟﺎﺣ ﻲﻓ ﺐﺒﺴﺘﺗ ﺔﺑﺎﺻﺍ ﺔﻳﺪﺴﺟ ﺰﻣﺮﻟﺍ ﺍﺬﻫ ﻲﻨﻌﻳ ﺮﻄﺧ !ﺮﻳﺬﺤﺗ

ﻥﺃ ﻞﺒﻗ ﻱﺃ ﻰﻠﻋ ﻞﻤﻌﺗ ﺕﺍﺪﻌﻣ،ﻛﻢﻠﻋ ﻰﻠﻋ ﻦ ﻦﻋ ﺔﻤﺟﺎﻨﻟﺍ ﺮﻁﺎﺨﻤﻟﺎﺑ ﺮﺋﺍﻭﺪﻟﺍ

ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ

ﻛﻭﺔﻳﺍﺭﺩ ﻰﻠﻋ ﻦ ﺭﺎﻤﻤﻟﺎﺑﺕﺎﺳ ﺔﻴﺋﺎﻗﻮﻟﺍ ﻟ ﻊﻨﻤﻉﻮﻗﻭ ﻱﺃﺙﺩﺍﻮﺣ

ﻢﻗﺭ ﻡﺪﺨﺘﺳﺍ ﻥﺎﻴﺒﻟﺍ ﺹﻮﺼﻨﻤﻟﺍ ﺔﻳﺎﻬﻧ ﻲﻓ ﺮﻳﺬﺤﺗ ﻞﻛ ﺭﻮﺜﻌﻠﻟ ﺎﻬﺘﻤﺟﺮﺗ

안전을 위한 주의사항

경고!

이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수
있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와
관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준
작업절차를 준수해 주시기 바랍니다.

해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를
참조하십시오

BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die

lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,
dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's
en dient u op de hoogte te zijn van de standaard procedures om ongelukken te
voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te
herleiden naar de desbetreffende locatie.

BEWAAR DEZE INSTRUCTIES

4-3

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Installation Instructions

Warning!

Read the installation instructions before connecting the system to the power source.

設置手順書

システムを電源に接続する前に、設置手順書をお読み下さい。

警告
将此系统连接电源前,请先阅读安装说明。

警告
將系統與電源連接前，請先閱讀安裝說明。

Warnung
Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen

lesen.

¡Advertencia!
Lea las instrucciones de instalación antes de conectar el sistema a la red de

alimentación.

Attention
Avant de brancher le système sur la source d'alimentation, consulter les directives

d'installation.

אורקל שי רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תאחתמ.

ﻟﺍ ﺕﺍﺩﺎﺷﺭﺇ ﺮﻗﺍﺐﻴﻛﺮﺘ ﻞﻴﺻﻮﺗ ﻞﺒﻗ ﻰﻟﺇ ﻡﺎﻈﻨﻟﺍ ﺔﻗﺎﻄﻠﻟ ﺭﺪﺼﻣ

시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오.

Waarschuwing
Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron

aansluit.

4-4

Chapter 4: Warning Statements for AC Systems

Circuit Breaker

Warning!

This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.

サーキット・ブレーカー

この製 品 は、短絡（過電流）保護装置がある建物での設置を前提としています。

保護装置の定格が250V、20Aを超えないことを確認下さい。

警告
此产品的短路(过载电流)保护由建筑物的供电系统提供,确保短路保护设备的额定电
流不大于250V,20A。

警告
此產品的短路(過載電流)保護由建築物的供電系統提供,確保短路保護設備的額定電
流不大於250V,20A。

Warnung
Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss-

bzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der
Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt.

¡Advertencia!
Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes)

del edifi cio. Asegúrese de que el dispositivo de protección no sea superior a: 250
V, 20 A.

Attention
Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit

dépend de l'installation électrique du local. Vérifi ez que le courant nominal du
dispositif de protection n'est pas supérieur à :250 V, 20 A.

ﺞﺘﻨﻤﻟﺍ ﺍﺬﻫ ﻰﻠﻋ ﺪﻤﺘﻌﻳ ﺕﺍﺪﻌﻣ ﺔﻳﺎﻤﺤﻟﺍ ﺓﺮﻴﺼﻘﻟﺍﺮﺋﺍﻭﺪﻟﺍ ﻦﻣ ﺎﻬﺘﻴﺒﺜﺗ ﻢﺗ ﻲﺘﻟﺍ ﻲﻓ

לע ךמתסמ הז רצומנגהה תעינמל םינבמב תנקתומה יכ אדוול שי .ילמשח רצק

רצקה ינפמ ןגמה רישכמה ילמשחהמ רתוי אל אוה-250 V, 20 A

ﻰﻨﺒﻤﻟﺍ

20A, 250V : ﻦﻣ ﺪﻛﺄﺗ ﻥﺃ ﻢﻴﻴﻘﺗ ﺯﺎﻬﺠﻟﺍ ﻟﺍﻲﺋﺎﻗﻮ ﺲﻴﻟ ﻦﻣ ﺮﺜﻛﺃ

4-5

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

경고!

이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에
의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지
않도록 해야 합니다.

Waarschuwing
Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van

uw electrische installatie. Controleer of het beveiligde aparaat niet groter
gedimensioneerd is dan 220V, 20A.

Power Disconnection Warning

Warning!

The system must be disconnected from all sources of power and the power cord
removed from the power supply module(s) before accessing the chassis interior to
install or remove system components.

電源切断の警告
システムコンポーネントの取り付けまたは取り外しのために、シャーシー内部にアクセス

するには、
システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り

外す必要があります。

警告

在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。

警告

在您打開機殼安裝或移除內部元件前，必須將系統完全斷電，並移除電源線。

Warnung
Das System muss von allen Quellen der Energie und vom Netzanschlusskabel

getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es
auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder
zu entfernen.

4-6

Chapter 4: Warning Statements for AC Systems

ילמשח קותינ ינפמ הרהזא

!הרהזא

¡Advertencia!
El sistema debe ser disconnected de todas las fuentes de energía y del cable

eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso
el interior del chasis para instalar o para quitar componentes de sistema.

Attention
Le système doit être débranché de toutes les sources de puissance ainsi que de

son cordon d'alimentation secteur avant d'accéder à l'intérieur du chassis pour
installer ou enlever des composants de systéme.

למשחה תורוקמ לכמ תכרעמה תא קתנל שי ריסהל שיו קפסהמ ילמשחה לבכ תא

נקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפלת רסה ואת .םיביכר

ﻞﺼﻓ ﺐﺠﻳ ﻡﺎﻈﻨﻟﺍ ﻊﻴﻤﺟ ﻦﻣﺭﺩﺎﺼﻣ ﺔﻗﺎﻄﻟﺍ ﺔﻟﺍﺯﺇﻭ ءﺎﺑﺮﻬﻜﻟﺍ ﻚﻠﺳ ﻦﻣ ﺓﺪﺣﻭ ﺩﺍﺪﻣﺍ

ﺔﻗﺎﻄﻟﺍ ﻞﺒﻗ

ﺯﺎﻬﺠﻟﺍ

경고!

시스템에 부품들을 장착하거나 제거하기 위해서는 섀시 내부에 접근하기 전에
반드시 전원 공급장치로부터 연결되어있는 모든 전원과 전기코드를 분리해주어야
합니다.

Waarschuwing
Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren

of verwijderen van systeem onderdelen, dient u alle spanningsbronnen en alle
stroomkabels aangesloten op de voeding(en) van de behuizing te verwijderen

ﻰﻟﺇ ﻝﻮﺻﻮﻟﺍ ﺔﻴﻠﺧﺍﺪﻟﺍ ﻖﻁﺎﻨﻤﻟﺍ ﻟﻞﻜﻴﻬﻠ ﺔﻟﺍﺯﺇ ﻭﺃ ﺖﻴﺒﺜﺘﻟ ﺕﺎﻧﻮﻜﻣ

4-7

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Equipment Installation

Warning!

Only trained and qualifi ed personnel should be allowed to install, replace, or service
this equipment.

機器の設置

トレーニングを受け認定された人だけがこの装置の設置、交換、またはサービスを許可
されています。

警告
只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。

警告
只有經過受訓且具資格人員才可安裝、更換與維修此設備。

Warnung
Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,

qualifi ziertem Personal gestattet werden.

¡Advertencia!
Solamente el personal califi cado debe instalar, reemplazar o utilizar este equipo.

Attention
Il est vivement recommandé de confier l'installation, le remplacement et la

maintenance de ces équipements à des personnels qualifi és et expérimentés.

!הרהזא

שר דבלב ךמסומ תווצתא ףילחהל ,ןיקתהל יא .דויצה רובע תוריש תתל וא דויצה

ﻦﻴﺑﺭﺪﻤﻟﺍﻭ ﻭ ﺐﻴﻛﺮﺘﻟﻝﺍﺪﺒﺘﺳﺍ ﻭﺃ ﺔﻣﺪﺧ ﺯﺎﻬﺠﻟﺍ ﺍﺬﻫ ﺢﻤﺴﻳ ﻥﺃ ﺐﺠﻳ ﻂﻘﻓ ﻦﻴﻠﻫﺆﻤﻟﺍ ﻦﻴﻔﻅﻮﻤﻠﻟ

경고!

훈련을 받고 공인된 기술자만이 이 장비의 설치, 교체 또는 서비스를 수행할 수
있습니다.

4-8

Chapter 4: Warning Statements for AC Systems

Waarschuwing
Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door

geschoold en gekwalifi ceerd personeel.

Restricted Area

Warning!

This unit is intended for installation in restricted access areas. A restricted access
area can be accessed only through the use of a special tool, lock and key, or other
means of security. (This warning does not apply to workstations).

アクセス制限区域
このユ ニットは 、アクセス制限区域に設置されることを想定しています。
アクセス制限区域は、特別なツール、鍵と錠 前、その他のセキュリティの手段を用いての

み出入りが可能です。

警告
此部件应安装在限制进出的场所，限制进出的场所指只能通过使用特殊工具、锁和
钥匙或其它安全手段进出的场所。

警告
此裝置僅限安裝於進出管制區域，進出管制區域係指僅能以特殊工具、鎖頭及鑰匙
或其他安全方式才能進入的區域。

Warnung
Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen.

Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und
Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich.

¡Advertencia!
Esta unidad ha sido diseñada para instalación en áreas de acceso restringido.

Sólo puede obtenerse acceso a una de estas áreas mediante la utilización de una
herramienta especial, cerradura con llave u otro medio de seguridad.

Attention
Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une

zone d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme
de verrouillage et une clé, ou tout autre moyen de sécurité.

4-9

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

תלבגומ השיג םע רוזא

!הרהזא

תרזעב תנתינ השיגה .השיג תלבגה םהב שיש םירוזאב הדיחיה תא ןיקתהל שי

.('דכו לוענמ ,חתפמ) דבלב החטבא ילכ

. ﺺﻴﺼﺨﺗ ﺓﺪﺣﻮﻟﺍ ﻩﺬﻫ ﻲﻓ ﺎﻬﺒﻴﻛﺮﺘﻟ ﻖﻁﺎﻨﻣ ﺓﺭﻮﻈﺤﻣ ﻢﺗ

ﺻﻮﻟﺍ ﻦﻜﻤﻳﻰﻟﺇ ﻝﻮ ﺔﻘﻄﻨﻣ ﺓﺭﻮﻈﺤﻣ ﻂﻘﻓ ﻡﺍﺪﺨﺘﺳﺍ ﻝﻼﺧ ﻦﻣ ،ﺔﺻﺎﺧ ﺓﺍﺩﺃ

ﻭﺃ ﻱﺃ ﻼﻟ ﻯﺮﺧﺃ ﺔﻠﻴﺳﻭﻥﺎﻣﻷ ﺡﺎﺘﻔﻣﻭ ﻞﻔﻗ

경고!

이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다. 특수도구, 잠금 장치 및
키, 또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다.

Waarschuwing
Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang.

Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te
maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.

Battery Handling

Warning!

There is the danger of explosion if the battery is replaced incorrectly. Replace the
battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメー
カーが推奨する型、または同 等のものを使用下さい。使用済電池は製造元の指示に従

って処 分して 下さい。

警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更
换原有电池。请按制造商的说明处理废旧电池。

警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有
電池。請按照製造商的說明指示處理廢棄舊電池。

4-10

Chapter 4: Warning Statements for AC Systems

!הרהזא

Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die

Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.

Attention
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer

que par une pile de type semblable ou équivalent, recommandée par le fabricant.
Jeter les piles usagées conformément aux instructions du fabricant.

¡Advertencia!
Existe peligro de explosión si la batería se reemplaza de manera incorrecta.

Reemplazar la batería exclusivamente con el mismo tipo o el equivalente
recomendado por el fabricante. Desechar las baterías gastadas según las
instrucciones del fabricante.

תנכס תמייקץוציפ .הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי

גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ.

תוללוסה קוליס תושמושמה עצבל שי .ןרציה תוארוה יפל

ﺮﻄﺧ ﻙﺎﻨﻫ ﻦﻣ ﻝﺍﺪﺒﺘﺳﺍ ﺔﻟﺎﺣ ﻲﻓ ﺭﺎﺠﻔﻧﺍ ﺔﻳﺭﺎﻄﺒﻟﺍ ﺔﺤﻴﺤﺻ ﺮﻴﻏ ﺔﻘﻳﺮﻄﺑ ﻚﻴﻠﻌﻓ

ﺔﻳﺭﺎﻄﺒﻟﺍ ﻝﺍﺪﺒﺘﺳﺍ

ﻂﻘﻓ ﻉﻮﻨﻟﺍ ﺲﻔﻨﺑ ﺎﻬﻟﺩﺎﻌﻳ ﺎﻣ ﻭﺃ ﺎﻤﻛﺖﺻﻭﺃ ﺔﻌﻨﺼﻤﻟﺍ ﺔﻛﺮﺸﻟﺍ ﻪﺑ

ﺕﺎﻳﺭﺎﻄﺒﻟﺍ ﻦﻣ ﺺﻠﺨﺗ ﻟ ﺎﻘﻓﻭ ﺔﻠﻤﻌﺘﺴﻤﻟﺍﺔﻌﻧﺎﺼﻟﺍ ﺔﻛﺮﺸﻟﺍ ﺕﺎﻤﻴﻠﻌﺘ

경고!

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와
동일하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다.
제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.

Waarschuwing
Er is ontploffi ngsgevaar indien de batterij verkeerd vervangen wordt. Vervang de

batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen
wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd
te worden.

4-11

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

דחא קפסמ רתוי םייק םא

!הרהזא

Redundant Power Supplies

Warning!

This unit might have more than one power supply connection. All connections must
be removed to de-energize the unit.

冗長電源装置

このユニットは複数の電源装置が接続されている場合があります。

ユニットの電源を切るためには、すべての接続を取り外さなければなりません。

警告
此部件连接的电源可能不止一个，必须将所有电源断开才能停止给该部件供电。

警告
此裝置連接的電源可能不只一個，必須切斷所有電源才能停止對該裝置的供電。

Warnung
Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass

der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.

¡Advertencia!
Puede que esta unidad tenga más de una conexión para fuentes de alimentación.

Para cortar por completo el suministro de energía, deben desconectarse todas las
conexiones.

Attention
Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute

tension et tout courant électrique de l'unité, toutes les connexions d'alimentation
doivent être débranchées.

.קפס לש דחא רוביחמ רתוי שי הדחיל תא ריסהל שיןקורל תנמ לע םירוביחה לכ

חיה תאי.הד

4-12

Chapter 4: Warning Statements for AC Systems

. ﺪﻗ ﺍﺬﻬﻟ ﻥﻮﻜﻳ ﻟﺍﺯﺎﻬﺠ ﺕﻻﺎﺼﺗﺍ ﺓﺪﻋ ﺕﺍﺪﺣﻮﺑ ﺔﻗﺎﻄﻟﺍ ﺩﺍﺪﻣﺍ

ﺔﻟﺍﺯﺇ ﺐﺠﻳ ﺕﻻﺎﺼﺗﻻﺍ ﺔﻓﺎﻛ ﻝﺰﻌﻟ ﻟﺍﺓﺪﺣﻮ ﻦﻋ ءﺎﺑﺮﻬﻜﻟﺍ

경고!

이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에
전원을 차단하기 위해서는 모든 연결 단자를 제거해야만 합니다.

Waarschuwing
Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle

aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken.

Backplane Voltage

Warning!

Hazardous voltage or energy is present on the backplane when the system is
operating. Use caution when servicing.

バックプレーンの電圧
システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。

修理する際には注意ください。

警告
当系统正在进行时，背板上有很危险的电压或能量，进行维修时务必小心。

警告
當系統正在進行時，背板上有危險的電壓或能量，進行維修時務必小心。

Warnung
Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche

Spannungen oder Energien auf. Vorsicht bei der Wartung.

¡Advertencia!
Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso.

Tenga cuidado cuando lo revise.

Attention
Lorsque le système est en fonctionnement, des tensions électriques circulent sur

le fond de panier. Prendre des précautions lors de la maintenance.

4-13

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

ירוחאה לנפב חתמ

ךלהמב רהזיהל שי .תכרעמה לועפת ןמזב ירוחאה לנפב חתמ תנכס תמייק

זא!הרה

.הדובעה

ﻙﺎﻨﻫ ﺮﻄﺧ ﻦﻣ ﻲﺋﺎﺑﺮﻬﻜﻟﺍ ﺭﺎﻴﺘﻟﺍ ﻰﻠﻋ ﺓﺩﻮﺟﻮﻤﻟﺍ ﺔﻗﺎﻄﻟﺍﻭﺃ ﺔﺣﻮﻠﻟﺍ

ﻥﻮﻜﻳ ﺎﻣﺪﻨﻋﻡﺎﻈﻨﻟﺍ ﻞﻤﻌﻳ ﺪﻨﻋ ﺍﺭﺬﺣ ﻦﻛ ﺔﻣﺪﺧ ﺯﺎﻬﺠﻟﺍ ﺍﺬﻫ

경고!

시스템이 동작 중일 때 후면판 (Backplane)에는 위험한 전압이나 에너지가 발생
합니다. 서비스 작업 시 주의하십시오.

Waarschuwing
Een gevaarlijke spanning of energie is aanwezig op de backplane wanneer het

systeem in gebruik is. Voorzichtigheid is geboden tijdens het onderhoud.

Comply with Local and National Electrical Codes

Warning!

Installation of the equipment must comply with local and national electrical codes.

地方および国の電気規格に準拠
機器の取り付けはその地方および国の電気規格に準拠する必要があります。

警告

设备安装必须符合本地与本国电气法规。

警告

設備安裝必須符合本地與本國電氣法規。

Warnung
Die Installation der Geräte muss den Sicherheitsstandards entsprechen.

¡Advertencia!
La instalacion del equipo debe cumplir con las normas de electricidad locales y

nacionales.

4-14

Chapter 4: Warning Statements for AC Systems

יצראה למשחה יקוח םואית

Attention
L'équipement doit être installé conformément aux normes électriques nationales

et locales.

!הרהזא

תנקתה םייצראהו םיימוקמה למשחה יקוחל תמאות תויהל תבייח דויצה.

ﺕﺍﺪﻌﻤﻟﺍ ﺐﻴﻛﺮﺗ ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﻠﻟ ﻞﺜﺘﻤﻳ ﻥﺃ ﺐﺠﻳ ﻦﻴﻧﺍﻮﻘﺔﻴﻨﻁﻮﻟﺍﻭ ﺔﻴﻠﺤﻤﻟﺍ ﺔﻘﻠﻌﺘﻤﻟﺍ

ءﺎﺑﺮﻬﻜﻟﺎﺑ

경고!

현 지역 및 국가의 전기 규정에 따라 장비를 설치해야 합니다.

Waarschuwing
Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale

elektriciteitsvoorschriften.

Product Disposal

Warning!

Ultimate disposal of this product should be handled according to all national laws
and regulations.

製品の廃棄

この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が
あります。

警告
本产品的废弃处理应根据所有国家的法律和规章进行。

警告
本產品的廢棄處理應根據所有國家的法律和規章進行。

Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen

des Landes erfolgen.

4-15

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

רצומה קוליס

¡Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y

reglamentos nacionales.

Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des

lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de
l'organisme compétent.

!הרהזא

ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס.הנידמה יקוח

ﻲﺋﺎﻬﻨﻟﺍ ﺺﻠﺨﺘﻟﺍ ﻦﻣ ﺞﺘﻨﻤﻟﺍ ﺍﺬﻫ ﻪﻌﻣ ﻞﻣﺎﻌﺘﻟﺍ ﻲﻐﺒﻨﻳ ﻟ ﺎﻘﻓﻭ ﻊﻴﻤﺠﺔﻴﻨﻁﻮﻟﺍ ﺢﺋﺍﻮﻠﻟﺍﻭ ﻦﻴﻧﺍﻮﻘﻟﺍ ﺪﻨﻋ

경고!

이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.

Waarschuwing
De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming

met alle nationale wetten en reglementen.

Hot Swap Fan Warning

Warning!

The fans might still be turning when you remove the fan assembly from the chassis.
Keep fi ngers, screwdrivers, and other objects away from the openings in the fan
assembly's housing.

ファン・ホットスワップの警告

シャーシから冷却ファン装置を取り外した際、ファンがまだ回転している可能性がありま

す。ファンの開口部に、指、ドライバー、およびその他のものを近づけないで下さい。

警告
当您从机架移除风扇装置，风扇可能仍在转动。小心不要将手指、螺丝起子和其他
物品太靠近风扇

4-16

Chapter 4: Warning Statements for AC Systems

警告
當您從機架移除風扇裝置，風扇可能仍在轉動。小心不要將手指、螺絲起子和其他
物品太靠近風扇。

Warnung
Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis

genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände
von den Öffnungen des Lüftergehäuses entfernt.

¡Advertencia!
Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador

del chasis. Mandtenga los dedos, los destornilladores y todos los objetos lejos de
las aberturas del ventilador

Attention
Il est possible que les ventilateurs soient toujours en rotation lorsque vous retirerez

le bloc ventilateur du châssis. Prenez garde à ce que doigts, tournevis et autres
objets soient éloignés du logement du bloc ventilateur.

!הרהזא

יקלח תא םיריסמ רשאכ שי .םידבוע ןיידע םיררוואמהו ןכתי ,זראמהמ ררוואמה

קיחרהללררוואמה ךותב םיחתפהמ םינוש הדובע ילכו תועבצאה תא חוטב קחרמ

ﻦﻜﻤﻤﻟﺍ ﻦﻣ ﺡﻭﺍﺮﻤﻟﺍ ﻥﺃ ﻝﺍﺰﺗ ﻻ ﺔﻟﺍﺯﺇ ﺪﻨﻋﺭﻭﺪﺗ ﺔﻠﺘﻛ ﺔﺣﻭﺮﻤﻟﺍ ﻞﻜﻴﻬﻟﺍ ﻦﻣ ﺐﺠﻳ ءﺎﻘﺑﺇ

ﻊﺑﺎﺻﻷﺍ ﻭﻲﻏﺍﺮﺒﻟﺍ ﺕﺎﻜﻔﻣ

. ءﺎﻴﺷﻷﺍ ﻦﻣ ﺎﻫﺮﻴﻏﻭ ﺍﺪﻴﻌﺑ ﻦﻋ ﺕﺎﺤﺘﻔﻟﺍ ﻲﻓ ﺔﻠﺘﻛ ﺔﺣﻭﺮﻤﻟﺍ

경고!

섀시로부터 팬 조립품을 제거할 때 팬은 여전히 회전하고 있을 수 있습니다. 팬
조림품 외관의 열려있는 부분들로부터 손가락 및 스크류드라이버, 다른 물체들이
가까이 하지 않도록 배치해 주십시오.

Waarschuwing
Het is mogelijk dat de ventilator nog draait tijdens het verwijderen van het

ventilatorsamenstel uit het chassis. Houd uw vingers, schroevendraaiers
en eventuele andere voorwerpen uit de buurt van de openingen in de
ventilatorbehuizing.

4-17

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Power Cable and AC Adapter

Warning!

When installing the product, use the provided or designated connection cables,
power cables and AC adaptors. Using any other cables and adaptors could cause
a malfunction or a fi re. Electrical Appliance and Material Safety Law prohibits the
use of UL or CSA -certifi ed cables (that have UL/CSA shown on the code) for any
other electrical devices than products designated by Supermicro only.

電源コードとACアダプター

製品を設置する場合、提供または指定された接続ケーブル、電源コードとACアダプター
を使用下さい。他のケーブルやアダプタを使用すると故障や火災の原因になることがあ

ります。電気用品安全法は、ULまたはCSA認定のケーブル(UL/CSEマークがコードに表

記)をSupermicroが指定する製品以外に使用することを禁止しています。

警告
安装此产品时,请使用本身提供的或指定的连接线,电源线和电源适配器.使用其它线
材或适配器可能会引起故障或火灾。除了Supermicro所指定的产品,电气用品和材
料安全法律规定禁止使用未经UL或CSA认证的线材。(线材上会显示UL/CSA符号)。

警告
安裝此產品時,請使用本身提供的或指定的連接線,電源線和電源適配器.使用其它線
材或適配器可能會引起故障或火災。除了Supermicro所指定的產品,電氣用品和材
料安全法律規定禁止使用未經UL或CSA認證的線材。(線材上會顯示UL/CSA符號)。

Warnung
Bei der Installation des Produkts, die zur Verfügung gestellten oder benannt

Anschlusskabel, Stromkabel und Netzteile. Verwendung anderer Kabel und Adapter
kann zu einer Fehlfunktion oder ein Brand entstehen. Elektrische Geräte und
Material Safety Law verbietet die Verwendung von UL-oder CSA-zertifi zierte Kabel,
UL oder CSA auf der Code für alle anderen elektrischen Geräte als Produkte von
Supermicro nur bezeichnet gezeigt haben.

¡Advertencia!
Al instalar el producto, utilice los cables de conexión previstos o designados, los

cables y adaptadores de CA. La utilización de otros cables y adaptadores podría
ocasionar un mal funcionamiento o un incendio. Aparatos Eléctricos y la Ley de
Seguridad del Material prohíbe el uso de UL o CSA cables certifi cados que tienen
UL o CSA se muestra en el código de otros dispositivos eléctricos que los productos
designados por Supermicro solamente.

4-18

Chapter 4: Warning Statements for AC Systems

אתמו םיילמשחמ י

Attention
Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné.

L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement
ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit
l'utilisation de UL ou CSA câbles certifi és qui ont UL ou CSA indiqué sur le code
pour tous les autres appareils électriques que les produits désignés par Supermicro
seulement.

AC

!הרהזא

AC רשא

םימאתמו םיקפס ,םילבכב שמתשהל שי ,רצומה תא םיניקתמ רשאכ

וא הלקתל םורגל לוכי רחא םאתמ וא לבכ לכב שומיש .ךכ םשל וקפוסו ודעונ

טב יקוחו למשח ירישכמב שומיש יקוח יפ לע .ילמשח רצק רוסיא םייק ,תוחי

UL ב וא- CSA לש דוק םהילע עיפומ ראשכ)

ב םיכמסומה םילבכב שמתשהל-

UL/CSA( רחא ילמשח רצומ לכ רובע.דבלב ורקימקרפוס ידי לע ןיוצ אלש

ﺐﻴﻛﺮﺗ ﺪﻨﻋ ﻡﺍﺪﺨﺘﺳﺍ ﺐﺠﻳ ﺯﺎﻬﺠﻟﺍ ﻭ،ﻞﻴﺻﻮﺘﻟﺍ ﺕﻼﺑﺎﻛ ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﺕﻼﺑﺎﻜﻟﺍ

ﺕﻻﻮﺤﻣﻭ ﺩﺩﺮﺘﻤﻟﺍ ﺭﺎﻴﺘﻟﺍ

. ﻥﺃ ﻱﺃ ﻡﺍﺪﺨﺘﺳﺍ ﺕﻼﺑﺎﻛ ﺕﻻﻮﺤﻣﻭ ﻯﺮﺧﺃ ﺐﺒﺴﺘﻳ ﻲﻓ ﻞﻄﻋ ﺙﻭﺪﺣ ﻖﻳﺮﺣ ﻭﺃ . ﻲﺘﻟﺍ

ﻚﻟ ﺎﻫﺮﻴﻓﻮﺗ ﻢﺗ ﺞﺘﻨﻤﻟﺍ ﻊﻣ

UL ﻭﺃ CSA ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﺓﺰﻬﺟﻷﺍ ﺩﺍﻮﻣﻭ ﻥﻮﻧﺎﻗ ﺔﻣﻼﺴﻟﺍ ﻡﺍﺪﺨﺘﺳﺍ ﺮﻈﺤﻳ ﺕﻼﺑﺎﻜﻟﺍ

ﻞﺒﻗ ﻦﻣ ﺓﺪﻤﺘﻌﻣ

Supermicro ﺓﺰﻬﺟﺃ ﻯﺮﺧﺃ ﺔﻴﺋﺎﺑﺮﻬﻛ ﺮﻴﻏ ﺕﺎﺠﺘﻨﻤﻟﺍ ﺔﻨﻴﻌﻤﻟﺍ ﻞﺒﻗ ﻦﻣ ﻱﻷ

(UL/CSA ﻞﻤﺤﺗ ﻲﺘﻟﺍﺔﻣﻼﻋ )

경고!

제품을 설치할 때에는 제공되거나 지정된 연결케이블과 전원케이블, AC어댑터를
사용해야 합니다. 그 밖의 다른 케이블들이나 어댑터들은 고장 또는 화재의 원인이
될 수 있습니다. 전기용품안전법 (Electrical Appliance and Material Safety
Law)은 슈퍼마이크로에서 지정한 제품들 외에는 그 밖의 다른 전기 장치들을
위한 UL또는 CSA에서 인증한 케이블(전선 위에 UL/CSA가 표시)들의 사용을
금지합니다.

Waarschuwing
Bij het installeren van het product, gebruik de meegeleverde of aangewezen kabels,

stroomkabels en adapters. Het gebruik van andere kabels en adapters kan leiden
tot een storing of een brand. Elektrisch apparaat en veiligheidsinformatiebladen wet
verbiedt het gebruik van UL of CSA gecertifi ceerde kabels die UL of CSA die op
de code voor andere elektrische apparaten dan de producten die door Supermicro
alleen.

4-19

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Notes

4-20

Chapter 5: Advanced Serverboard Setup

Chapter 5

Advanced Serverboard Setup

This ch apter cover s the ste ps requi red to inst all pro ces sors a nd heats inks to the
X9DRFF-7TG+/X9DRFF-7G+ serverboard, connect the data and power cables
and inst al l add -on c ar ds . A ll s erver bo ar d jum pe r s and conne ct i on s are d es c r ib ed
and a layout and q uic k r efer en ce c h art are in cl ud ed in t hi s ch apte r. Remember t o
close t h e ch as si s c o mp lete ly w he n you h ave fi nished wo r ki ng o n t he se rverb o ard
to protec t and co ol the sys tem suf fi ciently.

5-1 Handling the Serverboard

Static electrical discharge can damage electronic com ponents. To prevent damage
to printed circuit boards, it is important to handle them very carefully (see Chapter 4).
Also note that the size and weight of the serverboard can cause it to bend if handled
improperly, which may result in damage. To prevent the serverboard from bending,
keep one hand under the center of the board to support it when handling.

The following measures are generally suffi cient to protect your equipment from
static discharge.

Precautions

• Use a grounded wrist strap designed to prevent static discharge.

• Touch a grounded metal object before removing any board from its antistatic

bag.

• Handle a board by its edges only; do not touch its components, peripheral chips,

memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the serverboard, add-on cards and peripherals back into their antistatic

bags when not in use.

Unpacking

The serverboard is shipped in antistatic packaging to avoid static damage. When
unpacking the board, make sure the person handling it is static protected.

5-1

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

OPEN 1st

WARNING!

OPEN 1st

WARNING!

5-2 Installing the Processor and Heatsink

Warning: When handling the processor package, avoid placing direct pressure on the

label area of the fan.

Notes:

• Always connect the power cord last and always remove it before adding, re-

moving or changing any hardware components. Make sure that you install the
processor into the CPU socket before you install the CPU heatsink.

• If you buy a CPU separately, make sure that you use an Intel-certifi ed multi-

directional heatsink only.

• Make sure to install the serverboard into the chassis before you install the CPU

heatsinks.

• When receiving a serverboard without a processor pre-installed, make sure that

the plastic CPU socket cap is in place and none of the socket pins are bent;
otherwise, contact your retailer immediately.

• Refer to the Sup ermi cro web s ite for upd ates on CPU su ppor t.

Installing an LGA2011 Processor

Press down on

1. There are two levers on the
LGA2011 socket. First press and
release the load lever labeled
'Open 1st' on CPU Socket #1.

2. Press the second load lever
labeled 'Close 1st' to release the
load plate from its locked position.

Pull lever away
from the socket

the lever labeled

'Close 1st'

WARNING!

OPEN 1st

WARNING!

OPEN 1st

5-2

3. With the lever labeled 'Close

WARNING!

OPEN 1st

WARNING!

1st' fully retracted, gently push
down on t he 'O pen 1st' lever
to open the load plate. Lift the
load plate to open it completely.

4. Using your t humb an d the ind ex
fi nger, remove the ' WAR NIN G'
plastic c ap fr om the so cket.

5. Use your thumb and index
fi nger to hold the CPU by its
edges. Align the CPU keys,
which are semi-circle cutouts,
against the socket keys.

6. Once they are aligned, carefully
lower the CPU straight down
into the socket. (Do not drop
the CPU on the socket. Do not
move the CPU horizontally or
vertically and do not rub the
CPU against any pins of the
socket, which may damage the
CPU or the socket.)

Chapter 5: Advanced Serverboard Setup

WARNING!

OPEN 1st

Gently push
down to pop
the load plate
open.

WARNING!

Socket Keys

CPU Keys

5-3

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

OPEN 1s

t

OPEN 1st

Warning: You can only install the CPU to the socket in one direction. Make sure that
the CPU is properly inserted into the socket before closing the load plate. If it doesn't
close properly, do not force it as it may damage your CPU. Instead, open the load
plate again and double-check that the CPU is aligned properly.

7. With the CPU in the socket, in­spect the four corners of the CPU
to make sure that they are fl ush
with the socket.

8. Close the load plate. Lock the
lever labeled 'Close 1st', then lock
the lever labeled 'Open 1st'. Use
your thumb to gently push the
load levers down until the lever
locks.

9. Repeat steps to install a CPU to
CPU Socket #2 if needed.

Gently close

the load plate.

Push down and lock the

level labeled 'Close 1st'.

Lever Lock

OPEN 1st

OPEN 1st

Push down
and lock the
lever labeled

'Open 1st'.

5-4

Chapter 5: Advanced Serverboard Setup

Installing a CPU Heatsink

1. Place the heatsink on top of the CPU so that the four mounting holes are
aligned with those on the retention mechanism.

2. Screw in two diagonal screws (i.e. the #1 and the #2 screws) until just snug
(do not over-tighten the screws, which may damage the CPU.)

3. Finish the installation by fully tightening all four screws.

Removing the Heatsink

1. Unplug the power cord from the power supply.

2. Unscrew and remove the heatsink screws in the sequence shown in the
picture below.

3. Hold the heatsink and gently wiggle it to loosen it from the CPU. (Do not use
excessive force when doing this!)

4. Once the heatsink is loosened, remove it from the CPU.

5. Clean the surface of the CPU and the heatsink to get rid of the old thermal
grease. Reapply the proper amount of thermal grease before you re-install
the heatsink.

Warning: We do not recommend removing the CPU or the heatsink. If you do need
to remove the heatsink, please follow the instructions below to prevent damage to the
CPU or other components.

5-5

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

5-3 Connecting Cables

With the processors are installed, the next step is to connect the cables to the
serverboard.

Connecting Data Cables

The cables used to transfer data from the peripheral devices have been carefully
routed to prevent them from blocking the fl ow of cooling air that moves through the
system from front to back. When disconnecting any of these cables, take care to
reroute them as they were originally.

Up to 12 hard drives may be installed in the chassis using any combination of the
SAS and SATA ports below. See the serverboard layout diagram in this chapter for
connector locations.

• SAS (SAS0-SAS7) or SATA (SATA0-5) cables

Connecting Power Cables

The X9DRFF-7TG+/X9DRFF-7G+ has two 8-pin primary power supply connectors
designated JPW1 and JPW2 for connection to the ATX power supply. Connect the
approp riate conn ector fro m the power sup ply to JPW1/JPW2 to supp ly power to
the ser verb oard. Se e the Con necto r Defi nitions sect ion in thi s chapter fo r power
conne c tor p in d efi nitio ns. In addition, your power supply must be connected to the
4-pin processor power connector at JPW3.

5-4 I/O Ports

The I/O ports are color coded in conformance with the PC 99 specifi cation. See
Figure 5-1 below for the colors and locations of the various I/O ports.

Figure 5-1. I/O Ports

1 2 3 4 5

6 7

1. USB1 5. LAN2 Port*

2. USB2 6. VGA Port

3. Dedicated IPMI LAN 7. Power Button

4. LAN1 Port*

* 1 Gb ports on the 6017R-73HDP+ and 10 Gb ports on the 6017R-73THDP+

Rear I/O Ports

5-6

Chapter 5: Advanced Serverboard Setup

5-5 Installing Memory

Note: Check the Supermicro web site for recommended memory modules.

CAUTION

Exercise extreme care when installing or removing DIMM modules

to prevent any po ssibl e damage.

Installing DIMMs

1. Insert the desired number of DIMMs into the memory slots, starting with slot
P1-DIMMA1. For best performance, install memory modules of the same type
and same speed in the slots as indicated in the tables below.

2. Push the release tabs outwards on both ends of the DIMM slot to unlock it.
Insert each DIMM vertically into its slot. Pay attention to the notch along the
bottom of the module to prevent inserting the DIMM module incorrectly (see
Figure 5-2).

3. Gently press down on the DIMM module until it snaps into place in the slot.
Repeat for all modules

Memory Support

The X9DRFF-7TG+/X9DRFF-7G+ has 16 memory sockets that can support up to
512 GB of ECC registered DDR3-1600/1333/1066/800 RDIMMs or up to 128 GB
of unbuffered ECC/non-ECC DDR3-1600/1333/1066/800 UDIMMs. Please refer to
Chapter 5 for installing memory.

Figure 5-2. Installing DIMM into Slot

To Ins tall : Inser t

module vertically
and pre ss dow n
until it s naps i nto
place. Pay attention
to the alignment
notch at t he bo tto m.

To Remove:

Use your thumbs to
gently push the re­lease tabs near both
ends of the module.
This should release
it from the slot.

Notch

Release Tab

Front View

Note: Notch should
align with the recep­tive key point on
the slot.

Notch

Release Tab

Top View of DDR3 Slot

5-7

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Processor & Memory Module Population Confi guration

For memor y to wor k pro perl y, follow the tab les be low for me mor y inst allati on.

Processors and their Corresponding Memory Modules

CPU# Corresponding DIMM Modules

CPU 1 P1-

DIMMA1

CPU2 P2-

DIMME1

Processor and Memory Module Population for Optimal Performance

Number of

CPUs+DIMMs

1 CPU &

2 DIMMs

1 CPU &

4 DIMMs

1 CPU &

5~8 DIMMs

2 CPUs &

4 DIMMs

P1­DIMMB1

P2­DIMMF1

CPU1
P1-DIMMA1/P1-DIMMB1

CPU1
P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1

CPU1
P1-DIMMA1/P1-DIMMB1, P1-DIMMC1/P1-DIMMD1 + Any memory pairs in P1­DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2 slots

CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1, P2-DIMME1/P2-DIMMF1

P1­DIMMC1

P2­DIMMG1

CPU and Memory Population Confi guration Table

(For memory to work properly, please follow the tables below.)

P1­DIMMD1

P2­DIMMH1

P1­DIMMA2

P2­DIMME2

P1­DIMMB2

P2­DIMM F2

P1­DIMMC2

P2­DIMMG2

P1­DIMMD2

P2­DIMMH2

2 CPUs &

6 DIMMs

2 CPUs &

8 DIMMs

2 CPUs &

10~16 DIMMs

2 CPUs &

16 DIMMs

CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1

CPU1 + CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2­DIMMG1/P2-DIMMH1

CPU1/CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2­DIMMG1/P2-DIMMH1 + Any memory pairs in P1, P2 DIMM slots

CPU1/CPU2
P1-DIMMA1/P1-DIMMB1/P1-DIMMC1/P1-DIMMD1, P2-DIMME1/P2-DIMMF1/P2-DIM­MG1/P2-DIMMH1,P1-DIMMA2/P1-DIMMB2/P1-DIMMC2/P1-DIMMD2, P2-DIMME2/
P2-DIMMF2/P2-DIMMG2/P2-DIMMH2

5-8

Installing UDIMM (ECC/Non-ECC) Memory

Intel E5-2600 Series Processor UDIMM Memory Support

Ranks Per

DIMM &

Data Width

SRx8

Non-ECC

DRx8

Non-ECC

SRx16

Non-ECC

Memory Capacity

Per DIMM

(See the Note below)

1.35V 1.5V 1.35V 1.5V 1.35V 1.5V

1GB 2GB 4GB NA 1066,

2GB 4GB 8GB NA 1066,

512MB 1GB 2GB NA 1066,

Chapter 5: Advanced Serverboard Setup

Speed (MT/s) and Voltage Validated by Slot per

Channel (SPC) and DIMM Per Channel (DPC)

1 Slot Per

Channel

1DPC 1DPC 2DPC

1333,

1600

1333,

1600

1333,

1600

2 Slots Per Channel

NA 1066,

1333

NA 1066,

1333

NA 1066,

1333

NA 1066,

1333

NA 1066,

1333

NA 1066,

1333

SRx8 ECC 1GB 2GB 4GB 1066,

1333

DRx8 ECC 2GB 4GB 8GB 1066,

1333

Note: For detailed information on memory support and updates, please refer to the SMC Recommended
Memory List posted on our website at http://www.supermicro.com/support/resources/mem.cfm.

1066,
1333,

1600

1066,
1333,

1600

1066,

1333

1066,

1333

1066,

1333

1066,

1333

1066 1066,

1333

1066 1066,

1333

Installing RDIMM (ECC) Memory

Intel E5-2600 Series Processor RDIMM Memory Support

Ranks Per

DIMM &

Data Width

SRx8 1GB 2GB 4GB 1066,

DRx8 2GB 4GB 8GB 1066,

SRx4 2GB 4GB 8GB 1066,

Memory Capacity

Per DIMM

(See the Note Below)

Speed (MT/s) and Voltage Validated by Slot per

Channel (SPC) and DIMM Per Channel (DPC)

1 Slot Per

Channel

1DPC 1DPC 2DPC

1.35V 1.5V 1.35V 1.5V 1.35V 1.5V

1333

1333

1333

1066,
1333,

1600

1066,
1333,

1600

1066,
1333,

1600

2 Slots Per Channel

1066,

1333

1066,

1333

1066,

1333

1066,
1333,

1600

1066,
1333,

1600

1066,
1333,

1600

1066,

1333

1066,

1333

1066,

1333

1066,
1333,

1600

1066,
1333,

1600

1066,
1333,

1600

DRx4 4GB 8GB 16GB 1066,

QRx4 8GB 16GB 32GB 800 1066 800 1066 800 800

QRx8 4GB 8GB 16GB 800 1066 800 1066 800 800

Note: For detailed information on memory support and updates, please refer to the SMC Recommended

Memory List posted on our website at http://www.supermicro.com/support/resources/mem.cfm.

1333

5-9

1066,
1333,

1600

1066,

1333

1066,
1333,

1600

1066,

1333

1066,
1333,

1600

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

5-6 Adding PCI Cards

PCI Expansion Slots

A riser card (RSC-R1UFF-E8R) installed to the system allow you to add a PCI
expansion card. The 6017R-73THDP+/6017R-73HDP+ can support the use of one
half-height, full-length) expansion card with the pre-installed riser card.

PCI Card Installation

Before installing a PCI add-on card, make sure you power off the system fi rst and
remove the AC power cord from the power supply.

1. Begin by removing the top chassis cover.

2. Remove the latch from the expansion card slot at the rear of the chassis then
lift the riser card from the chassis.

3. Insert the PCI card into the riser card slot, pushing down with your thumbs
evenly on both sides of the card - note that the add-on card attaches to the
riser card with a single screw.

4. After the card has been installed, reinstall the riser card then reinsert the latch
back into the expansion card slot.

5. Replace the chassis cover.

6. Plug the AC power cord back in and restore power to the system.

5-10

5-7 Serverboard Details

Figure 5-3. SUPER X9DRFF-7TG+/X9DRFF-7G+ Layout

Chapter 5: Advanced Serverboard Setup

JPL1

JPME1

JPME2

JWD1
JI2C2

JI2C1

P1-DIMMC1

USB2

JP7

JIPMB1

JBR1

JPI2C1

P1-DIMMC2

CPU1 SLOT2 PCI-E 3.0X8

CPU1 SLOT1 PCI-E X16 PROPRIETARY SLOT

1

JP6

P1-DIMMD1

Intel LAN
CTRL

CPU1 SLOT3 PCI-E 3.0X8

P1-DIMMD2

CLOSE 1st

UID_SW1

FAILURE_LED1

UID_LED1

PWR_SW1

BMC_HB_LED1

BMC

BIOS

CPLD1

X9DRFF-iG+

Rev. 1.01

CPU2

VGA1

JPB1

JPG1

LAN2

PCH SLOT4 PCIE-E 2.0X4

Intel PCH

JBT1

JBAT1

P1-DIMMB2

HDD_PWR2

LAN1

P1-DIMMA2

P1-DIMMB1

IPMI_ LAN

COM1

HDD_ACT_LED1

IPMI CODE

MEGERAC LICENSE

SAS CODE

LEDS2

LSI SAS
CTRL

T-SGPIO2

T-SGPIO1

P1-DIMMA1

I-SATA0

I-SATA1

L-SAS1

USB0

USB1

S-SATA0

JTPM1

JPT1

6-SGPIO2

6-SGPIO1

L-SAS5

L-SAS3

JSD1

MAC CODE

JPS1

I-SATA2

L-SAS0

L-SAS7

I-SATA3

I-SATA4

L-SAS2

L-SAS4

I-SATA5

L-SAS6

OPEN 1st

SXB1:CPU2 PCI-E X32

PROPRIENTAR SLOT

P2-DIMMG2

P2-DIMMH1

P2-DIMMH2

FAN7

CPU1

CLOSE 1st

OPEN 1st

FAN8

FAN6

FAN5

FAN3

FAN4

JPW3

PS_ON_N

P2-DIMMG1

Rear_FAN

JPW2

Notes

Jumpers not indicated are for test purposes only.

P2-DIMMF1

P2-DIMME2

P2-DIMMF2

P2-DIMME1

JPW1

HDD
PWR1

FAN1

FAN2

The X9DRFF-7TG+ includes 10 GB Ethernet ports (only change from the -7G+)

5-11

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

X9DRFF-7TG+/X9DRFF-7G+ Quick Reference

Jumper Description Default Setting

JBT1 Clear CMOS See Section 5-9

2

JI

C1/JI2C2 SMB to PCI-E Slots Open (Disabled)
JPB1 BMC Enable Pins 1-2 (Enabled)
JPG1 VGA Enable Pins 1-2 (Enabled)
JPL1 LAN1/LAN2 Enable Pins 1-2 (Enabled)
JPS1 SAS Enable Pins 1-2 (Enabled)
JWD1 Watch Dog Timer Enable Pins 1-2 (Reset)

Connector Description

FAN1-FAN8, Rear_FAN1 CPU/System/Cooling Fan Headers
HDD_PWR1/HDD_PWR2 8-pin Power Supply Connectors for HDD Device Use
I-SATA 0/1 SATA 3.0 Connectors 0/1 from Intel AHCI
I-SATA 2-5 SATA 2.0 Connectors 2/3/4/5 from Intel AHCI
JIPMB1 4-pin External BMC I

2

JPI

C1 Power Supply SMBbus I2C Header

2

C Header (for IPMI Card)

JPW1/JPW2 8-pin Power Connectors
JPW3 4-pin Power Connector
JSD1 SATA Device Power Connector
JTPM1 TPM (Trusted Platform Module)/Port 80 Connector
(J) USB2 Internal USB 2 Port
L-SAS 0-7 SAS Ports 0-7 from LSI 2308 SAS Controller
6-SGPIO 1/2 Serial Link General Purpose I/O Headers for SAS
T-SGPIO 1/2 Serial Link General Purpose I/O Headers for SATA
PWR_SW1 Power Switch (Button)
UID_SW1 UID (Unit Identifi er) Switch (SW1)
USB0/USB1 Front Panel USB 0/ USB1 Ports

LED Description State: Status

BMC_HB_LED1 BMC Heartbeat LED Blinking Green: BMC Normal
HDD_ACT LED1 HD D Acti vity L ED Blinking Green: HDD Active

Failure_LED1 Failu re LED

LEDS2 SAS Heartbeat LED On (Green): SAS Normal
UID_LED1 UID LED On (Blue): Unit Identifi ed

Blinking On: Power Failure; Blinking:
Fan Failure

5-12

5-8 Connector Defi nitions

ATX Power Connector

Two 8-pin power connectors (JPW1/
JPW2) and a 4-pin power connector
(JPW3) are used to provide power to
the serverboard. In addition, two 8-pin
power connectors (HDD_PWR1/2) are
also located onboard to provide power
from the serverboard to the HDD back­plane for HDD device use. Do not use
these connectors for other purposes.
All power connectors mentioned above
meet the SSI EPS 12V specifi cation. See
the tables on the right for pin defi nitions.

Chapter 5: Advanced Serverboard Setup

12V 8-pin PWR
Pin Defi nitions

Pins Defi nition

1- 4 Ground
5-8 +12V

HDD PWR

Pin Defi nitions

Pins Defi nition

1- 4 Ground
5-6 +12V
7-8 +5V

12V 4-pin PWR
Pin Defi nitions

Pins Defi nition

1 Ground
2 Ground
3 5V SB
4 PS_ON_N

Universal Serial Bus (USB)

Two Universal Serial Bus ports (USB0,
USB1), located on the I/O front panel,
provide front-accessible USB support.
In addition, a Type A USB connec­tor (JUSB2), located next to the 4-pin
JIPMB1 connector, also provides front­accessible USB support.

Ethernet Ports

Two Ethernet ports (LAN1, LAN2) are
located on the I/O front panel. These
Ethernet ports support 10G LAN connec­tions on the X9DRFF-7TG+, and 1G LAN
connections on the X9DRFF-7G+. In ad­dition, an IPMI LAN port is also located
on the front panel. All these ports accept
RJ45 cables. Please refer to the LED In­dicator Section for LAN LED information.

Front Panel USB 0/1

& Type A USB 2

Pin Defi nitions

Pin# Defi nition
1 +5V
2 PO­3 PO+
4 Ground

LAN Ports

Pin Defi nition

Pin# Defi nition Pin# Defi nition
1 P2V5SB 10 SGND
2 TD0+ 11 Act LED
3 TD0- 12 P3V3SB
4 TD1+ 13 Link 100 LED (Yel-

low, +3V3SB)

5 TD1- 14 Link 1000 LED

(Yellow, +3V3SB)
6 TD2+ 15 Ground
7 TD2- 16 Ground
8 TD3+ 17 Ground
9 TD3- 18 Ground

5-13

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Power Button/Unit Identifi er Switch

A Unit Identifier switch (SW1) and a
UID LED Indicator are located on the
serverboard. In addition, a power button
(PWR_SW1) is located next to the UID
switch on the front panel. When you press
the UID switch, the UID LED Indicator will
be turned on. Press the UID switch again
to turn off the UID LED. The UID Indicator
provides easy identifi cation of a system
unit that may be in need of service.

Note: UID can also be triggered via IPMI
on the serverboard. For more information
on IPMI, please refer to the IPMI User's
Guide posted on our website @http://
www.supermicro.com.

UID Switch

Pin# Defi nition
1 Ground
2 Ground
3 Button In
4 Ground

UID LED

Status

Color/State OS Status
Blue: On Windows OS Unit Identifi ed
Blue:

Blinking

Linux OS Unit Identifi ed

Fan Headers

This serverboard has eight 4-pin
(Fan1~Fan8), and one 3-pin (Rear_Fan1)
system/CPU/cooling fan headers on the
serverboard. The 4-pin fan headers are
backward compatible with traditional
3-pin fans. However, fan speed control
is only available on 4-pin fans via IPMI
fi rmware management. See the table on
the right for pin defi nitions.

IPMB

A System Management Bus header for
IPMI 2.0 is located at JIPMB1. Connect
the appropriate cable here to use the
IPMB I

2

C connection on your system.

Fan Header

Pin Defi nitions

Pin# Defi nition
1 Ground
2 +12V
3 Tachometer
4 PWR Modulation

(for 4-pin fans only)

IPMB Header

Pin Defi nitions

Pin# Defi nition
1 Data
2 Ground
3 Clock
4 No Connection

SATA Device Power Connector

A power connector for SATA DOM
(Disk_On_Module) devices is located at
JSD1. Connect an appropriate cable here
to provide power support for your SATA
DOM devices.

DOM PWR

Pin Defi nitions

Pin# Defi nition
1 +5V
2 Ground
3 Ground

5-14

T-SGPIO 1/2 & 6-SGPIO 1/2 Headers

Chapter 5: Advanced Serverboard Setup

Four SGPIO (Serial-Link General Pur­pose Input/Output) headers (T-SGPIO
1/2 & 6-SGPIO 1/2) are located on the
serverboard. These headers support on­board Serial_Link interface connections.
Note: T-SGPIO 1/2 support onboard
SATA connections. 6-SGPIO 1/2 support
the SAS interface.

Power SMB (I2C) Connector

Power System Management Bus (I
Connector (JPI

2

C1) monitors power sup-

2

C)

ply, fan and system temperatures. See
the table on the right for pin defi nitions.

T-SGPIO/6-SGPIO

Pin Defi nitions

Pin# Defi nition Pin Defi nition
2NC 1NC
4 Ground 3 Data

6 Load 5 Ground
8 Clock 7 NC

Note: NC=No Connection

PWR SMB

Pin Defi nitions

Pin# Defi nition
1 Clock
2 Data

3 PWR Fail
4 Ground
5 +3.3V

Power Switch

A power switch is located next to the UID
switch on the serverboard. Refer to the
layout below for the location.

Unit Identifi cation Switch/LED

A Unit Identifi er switch (UID) and a UID
LED indicator (UID_LED1) are located
next to the power switch on the front pan­el. When the user pushes the UID switch,
the UID LED (UID_LED1) will be turned
on. Push the UID switch again to turn off
the LED indicator. The UID switch pro­vides easy identifi cation of a system unit
that may be in need of service. See the
tables on the right for more information.

UID Switch (UID)

Pin Defi nitions

Pin# Defi nition
1 Ground
2 Ground
3 Button In
4 Ground

5-15

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

5-9 Jumper Settings

Explanation of Jumpers

To modify the operation of the
serverboard, jumpers can be used
to choose between optional settings.
Jumpers create shorts between two
pins to change the function of the
connector. Pin 1 is identifi ed with a
square solder pad on the printed cir­cuit board. See the diagram at right for
an example of jumping pins 1 and 2.
Refer to the serverboard layout page
for jumper locations.

Note: On two-pin jumpers, "Closed"
means the jumper is on and "Open"
means the jumper is off the pins.

Connector

Pins

Jumper

Setting

3 2 1

3 2 1

CMOS Clear

JBT1 is used to clear CMOS and will also clear any passwords. Instead of pins,
this jumper consists of contact pads to prevent accidentally clearing the contents
of CMOS.

To clear CMOS

1. First power down the system and unplug the power cord(s).

2. With the power disconnected, short the CMOS pads with a metal object such
as a small screwdriver.

3. Remove the screwdriver (or shorting device).

4. Reconnect the power cord(s) and power on the system.

Note: Do not use the PW_ON connector to clear CMOS.

GLAN Enable/Disable

JPL1 enables or disables LAN Port1/
LA N Port 2 on t he se r ver bo ard. S ee t he
table on the right for jumper settings.
The defau lt sett ing is Ena bled.

Jumper Setting Defi nition
Pins 1-2 Enabled (default)
Pins 2-3 Disabled

LAN Enable

Jumper Settings

5-16

Watch Dog Enable/Disable

JWD1 controls the Watch Dog function.
Watch Dog is a system monitor that can
reboot the system when a software appli­cation “hangs”. Pins 1-2 will cause WD to
reset the system if an application hangs.
Pins 2-3 will generate a non-maskable
interrupt signal for the application that
has hung. See the table on the right for
jumper settings. Watch Dog must also be
enabled in BIOS.

VGA Enable

Jumper JPG1 allows the user to en­able onboard VGA support. The default
setting is on pins 1-2 to enable VGA
support. See the table on the right for
jumper settings.

Chapter 5: Advanced Serverboard Setup

Watch Dog

Jumper Settings

Jumper Setting Defi nition
Pins 1-2 Reset
Pins 2-3 NMI
Open Disabled

VGA Enable

Jumper Settings

Jumper Setting Defi nition
Pins 1-2 Enabled (Default)
Pins 2-3 Disabled

BMC Enable

Jumper JPB1 allows you to enable the
embedded BMC (Baseboard Manage­ment) Controller to provide IPMI 2.0 sup­port on the serverboard. See the table on
the right for jumper settings.

I2C Bus to PCI-Exp. Slots

Jumpers JI

2

C1 and JI2C2 allow you to

connect the System Management Bus

2

(I

C) to PCI-Express slots. The default
setting is Open to disable the connec­tion.

SAS Enable

Use Jumper JPS1 to enable onboard
SAS support to enhance system perfor­mance. The default setting is enabled.

BMC Enable

Jumper Settings

Jumper Setting Defi nition
Pins 1-2 BMC Enable
Pins 2-3 Normal (Default)

I2C to PCI-Exp

Jumper Settings

Jumper Setting Defi nition
Closed Enabled
Open Disabled (Default)

SAS Support Enable

Jumper Settings

Jumper Setting Defi nition
Pins 1-2 SAS Enabled (Default)
Pins 2-3 SAS Disabled

5-17

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

5-10 Onboard Indicators

LAN LEDs

Link Speed LED

The Ethernet ports (located beside the
VGA port) have two LEDs. On each
Gigabit LAN port, one LED indicates ac­tivity when blinking while the other LED
may be green, amber or off to indicate
the speed of the connection. See the
table on the right for details on the con­nection speed LED.

IPMI Dedicated LAN LEDs

In addition to LAN Ports 1/2, an IPMI
Dedicated LAN is also located on the I/O
front panel. The amber L ED o n t h e right
indic ates con necti on and act ivit y; while
the gree n LED on the lef t indic ates the
speed of t he conn ectio n. See the t able
at right fo r more info rmati on.

Activity LED

GLAN Activity Indicator (Right)

Color Status Defi nition
Off No Connections
Yellow Flashing Active

Link Speed LED

IPMI LAN Link Speed LED (Left) &

Connection Activity LED (Right)

LED Color/State Defi nition
Off Off No Connection
Activity Amber:

Speed Green: Solid 100 Mbps

LED Settings

Activity LED

Active

Blinking

HDD Activity LED

An HDD Activity LED is located at
HDD_ACT LED1 on the serverboard.
When the HDD LED is blinking, an HDD
device is active. See the table at right for
more information.

BMC Heartbeat LED

A BMC Heartbeat LED is located at
BMC_HB_LED1 on the serverboard.
When this LED indicator is blinking, BMC
is nor mal. S ee t he t ab le at r ig ht for m or e
information.

SAS Heartbeat LED

A SAS Heartbeat LED is located at LEDS2
on the serverboard. When LEDS2 is blink­ing, SAS is working properly.

HDD Activity LED

Status

Color or State Defi nition
Green: Blink-

ing

Off

BMC Heartbeat LED

Color or State Defi nition
Green BMC: Normal

Off

SAS Heartbeat LED

Color/State Defi nition
Green: Blink-

ing

Off or Red

HDD: Active

HDD Disabled,
or Failed

Status

BMC Disabled,
or Failed

Status

SAS: Normal

SAS: Disabled
or Failed

5-18

Failure LED

Chapter 5: Advanced Serverboard Setup

A Failure LED is located at Failure_
LED1 on the serverboard. When Fail­ure_LED1 is on, power failure has oc­curred. When it is blinking, it indicates
a fan failure. See the table at right for
more information.

UID LED

The Unit Identifi er (UID) LED is loc ated
at UID_LED1 on the serverboard. When
this LED is o n, the unit t hat might b e in
need of service is identifi ed. See the
table at r ight for m ore info rmati on.

5-11 SAS/SATA Port Connections

Failure LED

Status

State Defi nition
On PWR Failure
Blinking Fan Failure

UID LED

Status

Color/State Defi nition
Blue: On Unit Identifi ed

SATA Ports

There are six Serial ATA Ports pro­vided on the serverboard. I-SATA0-1 are
SATA3 p orts a nd I - S ATA2- 5 ar e SATA2
por ts. See t he tabl e on the ri ght for pin
defi nitions.

SAS Ports

Eight Ser ial Att ached SC SI Port s (SAS
0-7) ar e prov id ed o n the s er ve r boa rd to
provide serial link connections. These
ports are supported by an LSI 2308
contr olle r. See the tabl e on th e righ t for
pin defi nitions.

SATA Port Pin Defi nitions

Pin # Defi nition
1 Ground
2 TXP
3 TXN
4 Ground
5 RXN
6 RXP
7 Ground

SAS Port Pin Defi nitions

Pin # Defi nition
1 Ground
2 TXP
3 TXN
4 Ground
5 RXN
6 RXP
7 Ground

5-19

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

5-12 Installing Software

The Supermicro ftp site contains drivers and utilities for your system at ftp://ftp.

supermicro.com. Some of these must be installed, such as the chipset driver.

After accessing the ftp site, go into the CDR_Images directory and locate the ISO
fi le for your serverboard. Download this fi le to create a CD/DVD of the drivers and
utilities it contains. (You may also use a utility to extract the ISO fi le if preferred.)

Another option is to go to the Supermicro Website at

products/. Find the product page for your serverboard here, where you may down-

load individual drivers and utilities.
After creating a CD/DVD with the ISO fi les, insert the disk into the CD/DVD drive

on your system and the display shown in Figure 5-4 should appear.

http://www.supermicro.com/

Figure 5-4. Driver/Tool Installation Display Screen

Note: Click the icons showing a hand writing on paper to view the readme fi les

for each item. Click the computer icons to the right of these items to install each
item (from top to the bottom) one at a time. After installing each item, you must
re-boot the system before moving on to the next item on the list. The bottom
icon with a CD on it allows you to view the entire contents.

5-20

Chapter 5: Advanced Serverboard Setup

SuperDoctor III

The SuperDoctor® III program is a web-based management tool that supports
remote management capability. It includes Remote and Local Management tools.
The local management is called SD III Client. The SuperDoctor III program allows
you to monitor the environment and operations of your system. SuperDoctor III
displays crucial system information such as CPU temperature, system voltages
and fan status. See the fi gures below for examples of the SuperDoctor III interface.

Note: The default User Name and Password for SuperDoctor III is ADMIN / ADMIN.
Note: When SuperDoctor III is fi rst installed, it adopts the temperature threshold

settings that have been set in BIOS. Any subsequent changes to these thresholds
must be made within SuperDoctor III, as the SuperDoctor III settings override the
BIOS settings. To set the BIOS temperature threshold settings again, you would
fi rst need to uninstall SuperDoctor III.

Figure 5-5. SuperDoctor III Interface Display Screen (Health Information)

5-21

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Figure 5-6. SuperDoctor III Interface Display Screen (Remote Control)

Note: The SuperDoctor III program and User ’s Manual can be downloaded from

the Supermicro web site at http://www.supermicro.com/products/accessories/soft-

ware/SuperDoctorIII.cfm

II application instead.

. For Linux, we recommend that you use the SuperDoctor

5-13 Onboard Battery

Please handle used batteries carefully. Do not damage the battery in any way; a
damaged battery may release hazardous materials into the environment. Do not
discard a used battery in the garbage or a public landfi ll. Please comply with the
regulations set up by your local hazardous waste management agency to dispose
of your used battery properly.

Figure 5-7. Installing the Onboard Battery

5-22

Chapter 6: Advanced Chassis Setup

Chapter 6

Advanced Chassis Setup

This chapter covers the steps required to install components and perform mainte­nance on the SC816L TS-655B chassis. For component installation, follow the steps
in the order given to eliminate the most common problems encountered. If some
steps are unnecessary, skip ahead to the step that follows.

Tools Required: The only tool you will need to install components and perform
maintainance is a Philips screwdriver.

6-1 Static-Sensitive Devices

Electrostatic Discharge (ESD) can damage electronic com ponents. To prevent
damage to any printed circuit boards (PCBs), it is important to handle them very
carefully. The following measures are generally suffi cient to protect your equipment
from ESD discharge.

Precautions

• Use a grounded wrist strap designed to prevent static discharge.

• Touch a grounded metal object before removing any board from its antistatic

bag.

• Handle a board by its edges only; do not touch its components, peripheral chips,

memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the serverboard, add-on cards and peripherals back into their antistatic

bags when not in use.

• For grounding purposes, make sure your computer chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and
the serverboard.

Unpacking

The serverboard is shipped in antistatic packaging to avoid static damage. When
unpacking the board, make sure the person handling it is static protected.

6-1

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Figure 6-1. Chassis Front View

LAN Ports

COM Port UID ButtonPower Button

Low-Profi le PCI-E Slot Covers

6-2 Removing the Covers

The SC816LT chassis features both a front and a rear cover, which allow access
to the interior of the chassis.

Removing the Chassis Covers

1. Remove the power cord from the rear of the chassis.

2. Remove the two screws securing the front cover to the front of the chassis.

3. Remove the four screws on the side and back edges of the front cover.

4. Lift the front cover up and off the chassis.

5. Remove the four screws on the front and back edges of the rear cover.

6. Lift the rear cover up and off the chassis.

Figure 6-2. Removing the Chassis Covers

6

4

2

6-2

Chapter 6: Advanced Chassis Setup

6-3 System Fans

Eight internal system fans in two separate fan housings provide cooling for the
system. The system fans are easily removed from the chassis with a screwdriver.

Replacing a System Fan

1. Determine the location of the failed fan. If necessary, briefl y remove the chas-
sis cover while the system is running in order to locate the failed fan.

2. Power down the chassis with the operating system, remove the power cord
from the rear of the power supply and remove the cover as described previ­ously.

3. Disconnect the fan wiring.

4. Remove the two screws securing the fan housing to the fl oor of the chassis.

5. Lift the fan housing up and out of the chassis.

6. To remove the fans in the left system fan housing:
Grasp the top of the failed fan. Lift it up and out of the housing.

To remove the fans in the right system fan housing:

Remove the four rubber plugs securing the fan into the housing.
Push upward on the underside of the failed fan, pushing it up and out of the
housing.

7. Insert a replacement fan into the fan housing. Confi rm that the replacement
fan is aligned in the same direction as the fan it replaces. If this is a right side
system fan, replace the four rubber plugs.

8. Replace the chassis cover, plug the power cord into the rear of the power
supply and power up the system.

6-3

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Left Side Fan Housing Right Side Fan Housing

Figure 6-3. Replacing the Left and Right Fan Housings

1

6

1

6

Left Side Fan Housing Right Side Fan Housing

Figure 6-4. Left and Right Fan Housings

6-4

Chapter 6: Advanced Chassis Setup

6-4 Drive Bay Installation/Removal

The SC816LT chassis contains twelve fi xed hard drives. Each hard drive and its
position in the chassis are labeled with a number that corresponds to the SATA
port on the serverboard.

10

11

07

02

08

12

05

06

03

01

Figure 6-5. Hard Drive Positions and their Corresponding SATA Ports

04

09

Replacing Hard Drives

Replacing a 3.5" Hard Drive

1. Power down the chassis with the operating system, remove the cord from the
rear of the power supply as described in Section 5-3 and remove the front
and rear covers as described in Section 5-4.

2. Locate the latch on the HDD you wish to remove from the chassis.

3. Press down on the latch to release the HDD from the fl oor of the chassis.

4. Slide the HDD forward to release it from the mounting bracket that secures it
to the fl oor of the chassis.

Warning! Enterprise level hard disk drives are recommended for use in Supermicro
chassis and servers. For information on recommended HDDs, visit the Supermicro Web
site at http://www.supermicro.com/products/nfo/fi les/storage/SAS-1-CompList-110909.
pdf

6-5

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

5. Lift the HDD up and out of the chassis, noting that the number on the fl oor of
the chassis and the corresponding number on the hard drive.

6. Transfer the number on the failed hard drive to the replacement hard drive.

7. Align the bracket on the underside of the replacement hard drive with the
mounting bracket on the fl oor of the chassis.

8. Slide the hard drive into the mounting bracket until it clicks in the locked posi­tion on the chassis fl oor.

3.5" HDD

HDD Latch

Figure 6-6. Installing 3.5" Hard Drives

6-6

Chapter 6: Advanced Chassis Setup

6-5 Installing Expansion Cards

The SC816LT chassis supports two low-profi le expansion cards Each expansion
card connects to the serverboard with a riser card. To install expansion cards, fol­low the instructions below.

Installing a Low-Profi le Expansion Card

1. Power down the system, remove the cord from the rear of the power supply
and remove the chassis covers as described previously.

2. Remove the six screws securing the riser card bracket to the chassis and set
them aside for later use.

3. Lift the riser card bracket up and out of the chassis.

4. Open the latch which secures the PCI-E slot cover to the riser card bracket.

5. Remove the PCI-E slot cover by sliding it sideways out of the PCIE slot.

6. Insert the expansion card into the riser card, simultaneously sliding the PCI-E
slot cover of the expansion card nto the PCI-E slot.

7. Insert the riser card into the serverboard and secure the riser card bracket to
the chassis with the screws previously set aside.

8. Place the chassis covers on top of the chassis and secure them with the
screws previously used for this purpose.

9. Plug the power cord into the rear of the power supply and power up the
system.

1

2

Figure 6-7. Removing the Riser Card Bracket from the Chassis

6-7

1

3

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

6-6 Replacing the Power Supply

The 6017R-73THDP+/6017R-73HDP+ includes a 655W power supply. This power
supply is auto-switching capable, which enables it to automatically sense and oper­ate at a 100 to 240 input voltage. An amber light will be illuminated on the power
supply when the power is off. An illuminated green light indicates that the power
supply is operating.

Power Supply Replacement

The system must be powered down to replace the power supply . Replacement units
can be ordered directly from Supermicro.

Changing the Power Supply

1. Power down the system and disconnect the AC power cord from the power
supply. Remove the chassis cover.

2. Remove tthe two screws that secure the power supply to the chassis, as il­lustrated below.

3. Press the release tab on the back of the power supply and pull the power
supply out using the handle provided.

4. Push the replacement power supply module into the power bay until it clicks
into the locked position. Secure with the screws previosuly removed.

5. Replace the chassis cover, then plug the AC power cord back into the power
supply and restore power to the system.

Screws

Figure 6-8. Replacing the Power Supply

6-8

Chapter 7: BIOS

Chapter 7

BIOS

7-1 Introduction

This chapter describes the AMI BIOS Setup utility for the X9DRFF-7G+. It also
provides the instructions on how to navigate the AMI BIOS Setup utility screens.
The AMI ROM BIOS is stored in a Flash EEPROM and can be easily updated.

Starting BIOS Setup Utility

To enter the AMI BIOS Setup utility screens, press the <Del> key while the system
is booting up.

Note: In most cases, the <Del> key is used to invoke the AMI BIOS setup
screen. There are a few cases when other keys are used, such as <F3>,
<F4>, etc.

Each main BIOS menu option is described in this manual. The Main BIOS setup
menu screen has two main frames. The left frame displays all the options that can
be confi gured. Grayed-out options cannot be confi gured. Options in blue can be
confi gured by the user. The right frame displays the key legend. Above the key
legend is an area reserved for informational text related to the option currently
selected in the left frame.

Note: The AMI BIOS has default informational messages built in. The
manufacturer retains the option to include, omit, or change any of these
informational messages.

The AMI BIOS Setup utility uses a key-based navigation system called "hot keys."
Most of the AMI BIOS setup utility "hot keys" can be used at any time during setup
navigation. These keys include <F3>, <F4>, <Enter>, <ESC>, arrow keys, etc.

Note 1: In this section, options printed in Bold are default settings.
Note 2: <F3> is used to load optimal default settings. <F4> is used to save

the settings and exit the setup utility.

7-1

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

How To Change the Confi guration Data

The confi guration data that determines the system parameters may be changed by
entering the AMI BIOS Setup utility. This Setup utility can be accessed by pressing
<Delete> at the appropriate time during system boot.

Note: For AMI UEFI BIOS Recovery, please refer to the UEFI BIOS Re­covery User Guide posted @http://www.supermicro.com/support/manuals/.

Starting the Setup Utility

Normally, the only visible Power-On Self-Test (POST) routine is the memory test.
As the memory is being tested, press the <Delete> key to enter the main menu of
the AMI BIOS Setup utility. From the main menu, you can access the other setup
screens. An AMI BIOS identifi cation string is displayed at the left bottom corner of
the screen below the copyright message.

Warning! Do not upgrade the BIOS unless your system has a BIOS-related issue.
Flashing the wrong BIOS can cause irreparable damage to the system. In no event
shall the manufacturer be liable for direct, indirect, special, incidental, or consequential
damage arising from a BIOS update. If you have to update the BIOS, do not shut down
or reset the system while the BIOS is being updated to avoid possible boot failure.

7-2 Main Setup

When you fi rst enter the AMI BIOS Setup utility , you will enter the Main setup screen.
You can always return to the Main setup screen by selecting the Main tab on the
top of the screen. The Main BIOS Setup screen is shown below.

7-2

Chapter 7: BIOS

The AMI BIOS main menu displays the following information:

System Date

This item displays the system date in Day MM/DD/YY format (e.g. Sat 10/20/2012).

System Time

This item displays the system time in HH:MM:SS format (e.g. 15:32:52).

Supermicro X9DRFF-iG+/iTG+/7G+/7TG+

Version

This item displays the SMC version of the BIOS ROM used in this system.

Build Date

This item displays the date that the BIOS ROM was built.

Memory Information

Total Memory

This displays the amount of memory available in the system.

7-3

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

7-3 Advanced Setup Confi gurations

Use the arrow keys to select the Advanced Setup submenu and press <Enter> to
access the following items.

Boot Feature

Quiet Boot

Use this item to select bootup screen display between POST messages and the
OEM logo. Select Disabled to display the POST messages. Select Enabled to
display the OEM logo instead of the normal POST messages. The options are

Enabled and Disabled.

AddOn ROM Display Mode

Use this item to set the AddOn Option ROM display mode. Select Keep Current to
use the current Option ROM display mode. Select Force BIOS to use the Option
ROM display mode set by the system BIOS. The options are Force BIOS and
Keep Current.

Bootup Num-Lock

Use this fe atur e to set t he Powe r-o n st ate for t he N um Lo ck key on t he keybo ard.
The opti ons are O f f and On.

Wait For 'F1' If Error

Selec t Enabl ed to fo rce t he system t o wait unt il the ' F1' key is pressed i f an er ror
occu rs. Th e optio ns are Di sable d and Enabled.

7-4

Chapter 7: BIOS

Interrupt 19 Capture

Interrupt 19 is the software interrupt that handles the boot disk function. When this
item is set to Enabled, the ROM BIOS of the host adaptors will "capture" Interrupt 19
at bootup and allow the drives that are attached to these host adaptors to function
as bootable disks. If this item is set to Disabled, the ROM BIOS of the host adap­tors will not capture Interrupt 19, and the drives attached to these adaptors will not
function as bootable devices. The options are Enabled and Disabled.

Re-try Boot

When the feature is set to Enabled, the BIOS will continuously retry to boot from
the selected boot type. The options are Disabled, Legacy Boot, and EFI Boot.

Power Confi guration

Watch Dog Function

If enabl ed, the Watc h Dog ti mer wil l set the sys tem to autom atic ally re boot wh en
a non- recoverab le error occ urs, and this e rror lasts fo r more than fi ve minutes.
The opti ons are En abled a nd Disabled.

Power Button Function

If this feature is set to Instant Off, the system will power off immediately as soon
as the user presses the power button. If this feature is set to 4 Seconds Override,
the system will power off when the user presses the power button for 4 seconds or
longer. The options are Instant Off and 4 Seconds Override.

Restore on AC Power Loss

Use this feature to set the power state after a power outage. Select Stay Off for the
system power to remain off after a power loss. Select Power On for the system
power to be turned on after a power loss. Select Last State to allow the system
to resume its last state before a power loss. The options are Power On, Stay Off,
and Last State.

CPU Confi guration

This submenu displays CPU information as detected by the BIOS. It also allows
the user to confi gure CPU settings.

7-5

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Socket 1 CPU Information, Socket 2 CPU Information

This submenu displays the following information on the CPUs installed in Socket
1 and Socket 2.

• Type of CPU

• CPU Signature

• Microcode Patch

• CPU Stepping

• Maximum CPU Speed

• Minimum CPU Speed

• Processor Cores

• Intel HT (Hyper-Threading) Technology

• Intel VT-x Technology

• Intel SMX Technology

• L1 Data Cache

• L1 Code Cache

• L2 Cache

• L3 Cache

CPU Speed
This item displays the speed of the CPU installed in the Socket specifi ed.

64-bit
This item indicates if 64-bit technology is supported by the CPU installed in the

Socket selected.

Clock Spread Spectrum

Select Enable to enable Clock Spectrum support, which will allow the BIOS to
monitor and attempt to reduce Electromagnetic Interference level caused by the
components whenever needed. The options are Disabled and Enabled.

7-6

Chapter 7: BIOS

RTID (Record Types IDs)

This feature displays the total number of Record Type IDs for local and remote
pools. The options are Optimal and Alternate.

Hyper-threading

Select Enabled to support Intel Hyper-threading Technology to enhance CPU per­formance. The options are Enabled and Disabled.

Active Processor Cores

Set to Enabled to use the processor's second core and above. (Please refer to Intel's
website for more information.) The options are All, 1, 2, 4, and 6.

Limit CPUID Maximum

Use this feature to set the maximum CPU ID value. Enable this function to boot
legacy operating systems that do not support processors with extended CPUID
functions. The options are Enabled and Disabled (for the Windows OS).

Execute Disable Bit (Available if supported by the OS & the CPU)

Select Enabled to enable the Execute Disable Bit which will allow the processor
to designate areas in the system memory where an application code can execute
and where it cannot, thus preventing a worm or a virus from fl ooding illegal codes
to overwhelm the processor or damage the system during an attack. The default is

Enabled. (Refer to Intel and Microsoft Web sites for more information.)

®

Intel

AES-NI

Select Enable to use the Intel Advanced Encryption Standard (AES) New Instruc­tions (NI) to ensure data security. The options are Enabled and Disabled.

MLC Streamer Prefetcher (Available when supported by the CPU)

If set to Enabled, the MLC (Mid-Level Cache) streamer prefetcher will prefetch
streams of data and instructions from the main memory to the L2 cache in the CPU
to improve CPU performance. The options are Disabled and Enabled.

MLC Spatial Prefetcher (Available when supported by the CPU)

If this feature is set to Disabled, the MLC spatial prefetcher will prefetch the cache
line for 64 bytes. If this Enabled, the MLC spatial prefetcher will prefetch both cache
lines for 128 bytes as comprised. The options are Disabled and Enabled.

DCU Streamer Prefetcher (Available when supported by the CPU)

If this item is set to Enabled, the Data Cache Unit (DCU) streamer prefetcher will
prefetch L1 data to speed up data accessing and processing to enhance CPU
performance. The options are Disabled and Enabled.

7-7

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

DCU IP Prefetcher

Select Enabled for DCU (Data Cache Unit) IP Prefetcher support, which will prefetch
IP addresses to improve network connectivity and system performance. The options
are Enabled and Disabled.

®

Intel

Virtualization Technology (Available when supported by the CPU)

Selec t Enabled for Intel Virtu alization Technology suppor t, which will allow one
platf orm to r un mult iple op erati ng system s and app licat ions i n indep endent p ar ti­tions, creating multiple "virtual" systems in one physical computer. The options
are Enabled and Disabled.

Note: If there is any change to this setting, you will need to power off and
restar t the system for the chang e to take effect. Please refe r to Intel’s
website for d etaile d infor matio n.)

 CPU Power Management Confi guration

This submenu allows the user to confi gure the following CPU Power Management
settings.

Power Technology

Select Energy Effi ciency to support power-saving mode. Select Custom to cus-
tomize system power settings. Select Disabled to disable power-saving settings.
The options are Disabled, Energy Effi cient, and Custom. If the option is set to
Custom, the following items will display:

EIST (Available when Power Technology is set to Custom)

EIST (Enhanced Intel SpeedStep Technology) allows the system to au­tomatically adjust processor voltage and core frequency to reduce power
consumption and heat dissipation. The options are Disabled and Enabled.

C1E Support (Available when Power Technology is set to Custom)

Select Enabled to enable Enhanced C1 Power State to boost system per­formance. The options are Enabled and Disabled.

CPU C3 Report (Available when Power Technology is set to Custom)

Select Enabled to allow the BIOS to report the CPU C3 State (ACPI C2) to
the operating system. During the CPU C3 State, the CPU clock generator
is turned off. The options are Enabled and Disabled.

7-8

Chapter 7: BIOS

CPU C6 Report (Available when Power Technology is set to Custom)

Select Enabled to allow the BIOS to report the CPU C6 State (ACPI C3) to
the operating system. During the CPU C6 State, the power to all cache is
turned off. The options are Enabled and Disabled.

CPU C7 Report (Available when Power Technology is set to Custom)

Select Enabled to allow the BIOS to report the CPU C7 State (ACPI C3) to
the operating system. CPU C7 State is a processor-specifi c low C-State.
The options are Enabled and Disabled.

Package C-State limit (Available when Power Technology is set to
Custom)

Use this feature to set the limit on the C-State package register. The options
are C0, C2, C6, and No Limit.

Energy Performance Bias

Use this feature to select an appropriate fan setting to maximize system
performance (with maximum cooling) or to maximize energy effi ciency
with maximum power saving). The fan speeds are controlled by fi rmware
management via IPMI 2.0. The options are Performance, Balanced Per-

formance, Balanced Energy, and Energy Effi cient.

Factory Long Duration Power Limit

This item displays the power limit (in watts) set by the manufacturer during
which long duration power is maintained.

Long Duration Power Limit

This item displays the power limit (in watts) set by the user during which
long duration power is maintained. The default setting is 0.

Factory Long Duration Maintained
This item displays the period of time (in seconds) set by the manufacturer

during which long duration power is maintained.

Long Duration Maintained

This item displays the period of time (in seconds) during which long duration
power is maintained. The default setting is 0.

Recommended Short Duration Power Limit

This item displays the short duration power settings (in watts) recommended
by the manufacturer.

7-9

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Short Duration Power Limit

This item displays the time period during which short duration power (in
watts)is maintained. The default setting is 0.

Chipset Confi guration

North Bridge

This feature allows the user to confi gure the settings for the Intel North Bridge.

Integrated IO Confi guration

Intel® VT-d

Select Enabled to enable Intel Virtualization Technology support for Direct I/O
VT-d

by reporting the I/O device assignments to the VMM (Virtual Machine

Monitor) through the DMAR ACPI tables. This feature offers fully-protected I/O

-resource sharing across Intel platforms, providing greater reliability, security
and availability in networking and data-sharing. The options are Enabled and
Disabled.

Aging Timer Rollover

Use this feature to confi gure Aging Timer Rollover settings. Select Default to al-
low the BIOS to confi gure Aging Timer Roller settings. The options are Default,
Disabled, 32us, 128 us and 512 us.

®

Intel

I/OAT

Select Enabled to enable Intel I/OA T (I/O Acceleration Technology), which signifi -
cantly reduces CPU overhead by leveraging CPU architectural demands, freeing
up the system resource for other tasks. The options are Disabled and Enabled.

DCA Support

Select Enabled to use Intel's DCA (Direct Cache Access) Technology to improve
data transfer effi ciency. The default setting is Enabled.

MMCFG BASE

This feature determines the lowest base address that can be assigned to PCI
devices. The lower the address, the less system memory is available (for 32-bit
OS). The higher the address, the less resources are allocated to PCI devices.
The options are 0x80000000, 0xA0000000, and 0xC0000000.

7-10

Chapter 7: BIOS

IIO 1 PCIe Port Bifurcation Control

This submenu confi gures the following IO PCIe Port Bifurcation Control settings
for the PCIe ports. It also determines how the available PCI-Express lanes are
distributed between the PCI-Exp. Root ports.

CPU 1 Slot J1 PCI-E 3.0 x16 Link Speed

Select GEN1 to enable PCI-Exp Generation 1 support for Slot J1. Select GEN2 to
enable PCI-Exp Generation 2 support for Slot J1. Select GEN3 to enable PCI-Exp
Generation 3 support for Slot J1. The options are GEN1, GEN2, and GEN3.

CPU 1 Slot J2 PCI-E 3.0 x8 Link Speed

Select GEN1 to enable PCI-Exp Generation 1 support for Slot J2. Select GEN2 to
enable PCI-Exp Generation 2 support for Slot J2. Select GEN3 to enable PCI-Exp
Generation 3 support for Slot J2. The options are GEN1, GEN2, and GEN3.

CPU 1 Slot J3 PCI-E 3.0 x8 Link Speed

Select GEN1 to enable PCI-Exp Generation 1 support for Slot J3. Select GEN2 to
enable PCI-Exp Generation 2 support for Slot J3. Select GEN3 to enable PCI-Exp
Generation 3 support for Slot J3. The options are GEN1, GEN2, and GEN3.

IIO 2 PCIe Port Bifurcation Control

This submenu confi gures the following IO PCIe Port Bifurcation Control settings
for the PCIe ports. It also determines how the available PCI-Express lanes are
distributed between the PCI-Exp. Root Ports.

CPU 2 Slot SXB1A PCI-E 3.0 x16 Link Speed

Select GEN1 to enable PCI-Exp Generation 1 support for Slot SXB1A. Select
GEN2 to enable PCI-Exp Generation 2 support for Slot SXB1A. Select GEN3 to
enable PCI-Exp Generation 3 support for Slot SXB1A. The options are GEN1,
GEN2, and GEN3.

CPU 2 Slot SXB1B PCI-E 3.0 x16 Link Speed

Select GEN1 to enable PCI-Exp Generation 1 support for Slot SXB1B. Select
GEN2 to enable PCI-Exp Generation 2 support for Slot SXB1B. Select GEN3 to
enable PCI-Exp Generation 3 support for Slot SXB1B. The options are GEN1,
GEN2, and GEN3.

QPI Confi guration

Current QPI Link Speed

This item displays the current speed of the QPI Link.

7-11

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Current QPI Link Frequency

This item displays the frequency of the QPI Link.

Isoc

Select Enabled to enable Isochronous support to meet QoS (Quality of Service)
requirements. This feature is especially important for virtualization technology.
The options are Enabled and Disabled.

QPI (Quick Path Interconnect) Link Speed Mode

Use this feature to select data transfer speed for QPI Link connections. The
options are Fast and Slow.

QPI Link Frequency Select

Use this feature to select the desired QPI frequency. The options are Auto, 6.4
GT/s, 7.2 GT/s, and 8.0 GT/s.

DIMM Confi guration

This section displays the following DIMM information.

Current Memory Mode

This item displays the current memory mode.

Current Memory Speed

This item displays the current memory speed.

Mirroring

This item displays if memory mirroring is supported by the motherboard. Memory
mirroring creates a duplicate copy of the data stored in the memory to enhance
data security.

Sparing

This item displays if memory sparing is supported by the motherboard. Memory
sparing enhances system performance.

DIMM Information

The submenu displays the status of a DIMM module detected by the BIOS.

CPU Socket 1 DIMM Information/CPU Socket 2 DIMM Information

Memory Mode

When Independent is selected, all DIMMs are available to the operating system.
When Mirroring is selected, the motherboard maintains two identical copies of all

7-12

Chapter 7: BIOS

data in memory for data backup. When Lockstep is selected, the motherboard
uses two areas of memory to run the same set of operations in parallel. The
options are Independent, Mirroring, and Lockstep.

DRAM RAPL Mode

RAPL (Running Average Power Limit) provides mechanisms to enforce power
consumption limits on supported processors The options are DRAM RAPL
MODE0, DRAM RAPL MODE1, and Disabled.

DDR Speed

Use this feature to force a DDR3 memory module to run at a frequency other
than what is specifi ed by the manufacturer. The options are Auto, Force DDR3-
800, Force DDR3-1066, Force DDR3-1333, Force DDR3-1600 and Force SPD.

Channel Interleaving

This feature selects from the different channel interleaving methods. The options
are Auto, 1 Way, 2 Way, 3, Way, and 4 Way.

Rank Interleaving

This feature allows the user to select a rank memory interleaving method. The
options are Auto, 1 Way, 2 Way, 4, Way, and 8 Way.

Patrol Scrub

Patrol Scrubbing is a process that allows the CPU to correct correctable memory
errors detected on a memory module and send the correction to the requestor
(the original source). When this item is set to Enabled, the IO hub will read and
write back one cache line every 16K cycles if there is no delay caused by internal
processing. By using this method, roughly 64 GB of memory behind the IO hub
will be scrubbed every day. The options are Enabled and Disabled.

Demand Scrub

Demand Scrubbing is a process that allows the CPU to correct correctable
memory errors found on a memory module. When the CPU or I/O issues a
demand-read command, and the read data from memory turns out to be a
correctable error, the error is corrected and sent to the requestor (the original
source). Memory is updated as well. Select Enabled to use Demand Scrubbing
for ECC memory correction. The options are Enabled and Disabled.

Data Scrambling

Select Enabled to enable data scrambling to ensure data security and integrity.
The options are Disabled and Enabled.

7-13

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Device Tagging

Select Enabled to support device tagging. The options are Disabled and En­abled.

Thermal Throttling

Throttling improves CPU reliability and reduces power consumption via automatic
voltage control during processor idle states. The options are Disabled and CLTT
(Closed Loop Thermal Throttling).

South Bridge Confi guration

This feature displays PCH information and allows the user to confi gure PCH settings.

PCH Information

The following PCH information will be displayed.

• Name: This item displays the name of the PCH chip.

• Stepping: This item displays the PCH stepping.

• USB Devices: This item displays the USB devices detected by the BIOS.

All USB Devices

Select Enabled to enable all USB ports/devices. The options are Disabled and

Enabled.

EHCI Controller 1/EHCI Controller 2 (Available when All USB Devices is set
to Enabled)

Select Enabled to enable EHCI (Enhanced Host Controller Interface) Controller 1
or Controller 2. The options are Disabled and Enabled.

Legacy USB Support (Available when USB Functions is not Disabled)

Select Enabled to support legacy USB devices. Select Auto to disable legacy sup­port if USB devices are not present. Select Disabled to have USB devices available
for EFI (Extensive Firmware Interface) applications only. The settings are Disabled,

Enabled and Auto.

Port 60/64 Emulation

Select Enabled to enable I/O port 60h/64h emulation support for the legacy USB
keyboard so that it can be fully supported by the operating systems that does not
recognize a USB device. The options are Disabled and Enabled.

7-14

Chapter 7: BIOS

EHCI Hand-Off

This item is for operating systems that do not support Enhanced Host Controller
Interface (EHCI) hand-off. When this feature is enabled, EHCI ownership will be
changed by the EHCI driver. The options are Disabled and Enabled.

SATA Confi guration

When this submenu is selected, the AMI BIOS automatically detects the presence
of IDE or SATA devices and displays the following items.

SATA Port0~SATA Port5: The AMI BIOS displays the status of each SATA port
as detected by the BIOS.

SATA Mode

Use this feature to confi gure SATA mode for a selected SATA port. The options are
Disabled, IDE Mode, AHCI Mode and RAID Mode. The following are displayed
depending on your selection:

IDE Mode

The following items are displayed when IDE Mode is selected:

Serial-ATA (SATA) Controller 0~1

Use this feature to activate or deactivate the SATA controller, and set the
compatibility mode. The options are Disabled, Enhanced, and Compatible.
The default for SATA Controller 0 is Compatible. The default of SATA Con­troller 1 is Enhanced.

AHCI Mode

The following items are displayed when the AHCI Mode is selected.

Aggressive Link Power Management

When Enabled, the SATA AHCI controller manages the power usage of the
components installed on the SATA link. The controller will put the link in a
low power mode during extended periods of I/O inactivity , and will return the
link to an active state when I/O activity resumes. The options are Enabled
and Disabled.

Port 0~5 Hot Plug
Select Enabled to enable hot-plug support for a particular port, which will

allow the user to change a hardware component or device without shutting
down the system. The options are Enabled and Disabled.

7-15

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Port 0~5 Staggered Spin-Up

Select Enabled to enable Staggered Spin-up support to prevent excessive
power consumption caused by multiple HDDs spinning-up simultaneously.
The options are Enabled and Disabled.

RAID Mode

The following items are displayed when RAID Mode is selected:

SATA RAID Option ROM/UEFI Driver

Use this feature to enable the onboard SA TA Option ROM or EFI driver. The
options are Enabled and Disabled.

Port 0~5 Hot Plug

Select Enabled to enable hot-plug support for the particular port. The options
are Disabled and Enabled.

PCIe/PCI/PnP Confi guration

Launch Storage Add-on Card OpROM Priority

Use this feature to select the Option ROM you want to use to boot the system when
there are multiple Option ROMs available in the system. The options are UEFI only
and Legacy only.

PCI Latency Timer

Use this feature to set the latency timer of each PCI device installed on a PCI bus.
Select 64 to set the PCI latency to 64 PCI clock cycles. The options are 32, 64,
96, 128, 160, 192, 224 and 248.

PERR# Generation

Select Enabled to allow a PCI device to generate a PERR number for a PCI Bus
Signal Error Event. The options are Enabled and Disabled.

SERR# Generation

Select Enabled to allow a PCI device to generate an SERR number for a PCI Bus
Signal Error Event. The options are Enabled and Disabled.

Maximum Payload

Select Auto to allow the system BIOS to automatically set the maximum payload
value for a PCI-E device to enhance system performance. The options are Auto,
128 Bytes and 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, and 4096 Bytes.

7-16

Chapter 7: BIOS

Maximum Read Request

Select Auto to allow the system BIOS to automatically set the maximum Read
Request size for a PCI-E device to enhance system performance. The options are

Auto, 128 Bytes, 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, and 4096 Bytes.

ASPM Support

Use this feature to set the Active State Power Management (ASPM) level for a
PCI-E device. Select Auto to allow the system BIOS to automatically set the ASPM
level for the system. Select Disabled to disable ASPM support. The options are

Disabled, and Auto.

Warning: Enabling ASPM support may cause some PCI-E devices to fail!

Above 4G Decoding (Available if the system supports 64-bit PCI decoding)

Select Enabled to decode a PCI device that supports 64-bit in the space above 4G
Address. The options are Enabled and Disabled.

CPU1 Slot J1 PCI-E 3.0 x16 OPROM

Selec t Enabled to en able Opti on ROM supp ort to boot the computer using a de­vice installed on the slot specifi ed above. The options are Enabled and Disabled.

CPU1 Slot J2/Slot J3 PCI-E 3.0 x8 OPROM

Selec t Enabled to en able Opti on ROM supp ort to boot the computer using a de­vice installed on the slot specifi ed above. The options are Enabled and Disabled.

PCH Slot J4 PCI-E 2.0 x4 OPROM

Selec t Enabled to en able Opti on ROM supp ort to boot the computer using a de­vice installed on the slot specifi ed above. The options are Enabled and Disabled.

CPU2 Slot SXB1A/Slot SXB1B PCI-E 3.0 x16 OPROM

Selec t Enabled to en able Opti on ROM supp ort to boot the computer using a de­vice installed on the slot specifi ed above. The options are Enabled and Disabled.

Onboard LAN Option ROM Select

Selec t iSC S I to use t he i SC SI O pti on RO M to b oot t he c om pute r usi ng a networ k
device. Select PXE (Preboot Execution Environment) to use an PXE Option ROM to
boot the computer using a network device. The options are PXE, iSCSI and FCoE.

Load Onboard LAN1 Option ROM/Load Onboard LAN2 Option ROM

Select Enabled to enable th e onboard LAN1 or LAN 2 Option ROM. This is to boot
the computer using a network device. The default setting fo r LAN1 Opt io n RO M i s
Enabled, and for L AN 2 Opti on ROM is Disabled.

7-17

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Load Onboard SAS OPROM

Select Enabled for onboard SAS Option ROM support. This is to boot the computer
using a SAS device. The options a re Dis abled a nd Enabled.

VGA Priority

This feature allows the user to select the graphics adapter to be used as the primary
boot device. The options are Onboard, and Offboard.

Network Stack

Select Enabled enable PXE (Preboot Execution Environment) or UEFI (Unifi ed
Extensible Firmware Interface) for network stack support. The options are Enabled
and Disabled.

IPv4 PXE Support (Available when Network Stack is set to Enabled)

Set this item to Enabled to activate IPv4 PXE Support. The options are Enabled
and Disabled.

IPv6 PXE Support (Available when Network Stack is set to Enabled)

Set this item to Enabled to activate IPv6 PXE Support. The options are Enabled
and Disabled.

Serial Port Console Redirection

COM 1/SOL

These two submenus allow the user to confi gure the following Console Redirection
settings for a COM port specifi ed by the user.

COM1/SOL (Serial Over LAN) Console Redirection

Select Enabled to use COM1 or SOL (Serial_Over_LAN) port selected by the user
for Console Redirection. The options are Enabled and Disabled. The default setting
for COM1 is Disabled, and for SOL is Enabled.

Console Redirection Settings

Use this feature to specify how the host computer will communicate with the client
computer, which is the remote computer used by the user.

Terminal Type

This feature allows the user to select the target terminal emulation type for Con­sole Redirection. Select VT100 to use the ASCII Character set. Select VT100+ to
add color and function key support. Select ANSI to use the Extended ASCII Char-

7-18

Chapter 7: BIOS

acter Set. Select VT-UTF8 to use UTF8 encoding to map Unicode characters
into one or more bytes. The options are ANSI, VT100, VT100+, and VT-UTF8.

Bits Per second

Use this feature to set the transmission speed for a serial port used in Console
Redirection. Make sure that the same speed is used in the host computer and the
client computer. A lower transmission speed may be required for long and busy
lines. The options are 9600, 19200, 38400, 57600 and 115200 (bits per second).

Data Bits

Use this feature to set the data transmission size for Console Redirection. The
options are 7 Bits and 8 Bits.

Parity

A parity bit can be sent along with regular data bits to detect data transmission
errors. Select Even if the parity bit is set to 0, and the number of 1's in data bits
is even. Select Odd if the parity bit is set to 0, and the number of 1's in data bits
is odd. Select None if you do not want to send a parity bit with your data bits
in transmission. Select Mark to add a mark as a parity bit to be sent along with
the data bits. Select Space to add a Space as a parity bit to be sent with your
data bits. The options are None, Even, Odd, Mark and Space.

Stop Bits

A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard
serial data communication. Select 2 Stop Bits if slower devices are used. The
options are 1 and 2.

Flow Control

Use this feature to set the fl ow control for Console Redirection to prevent data
loss caused by buffer overfl ow. Send a "Stop" signal to stop sending data when
the receiving buffer is full. Send a "Start" signal to start sending data when the
receiving buffer is empty. The options are None and Hardware RTS/CTS.

VT-UTF8 Combo Key Support

Select Enabled to enable VT-UTF8 Combination Key support for ANSI/VT100
terminals. The options are Enabled and Disabled.

Recorder Mode

Select Enabled to capture the data displayed on a terminal and send it as text
messages to a remote server. The options are Disabled and Enabled.

7-19

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Resolution 100x31

Select Enabled for extended-terminal resolution support. The options are Dis­abled and Enabled.

Legacy OS Redirection Resolution

Use this feature to select the number of rows and columns used in Console
Redirection for legacy OS support. The options are 80x24 and 80x25.

Putty KeyPad

This feature selects Function Keys and KeyPad settings for Putty, which is a
terminal emulator designed for the Windows OS. The options are VT100, LINUX,
XTERMR6, SCO, ESCN, and VT400.

Redirection After BIOS Post

Use this feature to enable or disable Legacy Console Redirection after BIOS
POST (Power On Self Test). When this feature is set to Bootloader, Legacy
Console Redirection is disabled before booting the OS. When this feature is
set to Always Enable, Legacy Console Redirection remains enabled during OS
bootup. The options are Always Enable and Bootloader.

Serial Port for Out-of-Band Management/Windows Emergency Management
Services (EMS)

The submenu allows the user to confi gure Console Redirection settings to support
Out-of-Band Serial Port management.

EMS Console Redirection

Select Enabled to select a COM Port for Console Redirection. The options are
Enabled and Disabled.



Console Redirection Settings (for EMS)

This feature allows the user to specify how the host computer will exchange
data with the client computer, which is the remote computer used by the user.

Out-of-Band Management Port

The feature selects a serial port used by the Microsoft Windows Emergency
Management Services (EMS) to communicate with a remote server. The options
are COM1 and SOL.

Terminal Type

Use this feature to select the target terminal emulation type for Console Redirec­tion. Select VT100 to use the ASCII character set. Select VT100+ to add color

7-20

Chapter 7: BIOS

and function key support. Select ANSI to use the extended ASCII character set.
Select VT-UTF8 to use UTF8 encoding to map Unicode characters into one or
more bytes. The options are ANSI, VT100, VT100+, and VT-UTF8.

Bits Per Second

This item sets the transmission speed for a serial port used in Console Redirec­tion. Make sure that the same speed is used in the host computer and the client
computer. A lower transmission speed may be required for long and busy lines.
The options are 9600, 19200, 57600, and 115200 (bits per second).

Flow Control

Use this feature to set the fl ow control for Console Redirection to prevent data
loss caused by buffer overfl ow. Send a Stop signal to stop sending data when
the receiving buffer is full. Send a Start signal to start sending data when the
receiving buffer is empty. The options are None, Hardware RTS/CTS, and
Software Xon/Xoff.

Data Bits, Parity, Stop Bits

The setting for each of these items is displayed.

ACPI Settings

Use this feature to confi gure Advanced Confi guration and Power Interface (ACPI)
power management settings for your system.

ACPI Sleep State

Use this feature to select the ACPI State when the system is in sleep mode. Select
S1 (CPU Stop Clock) to erase all CPU caches and stop executing instructions. In
this setting, power to the CPU(s) and RAM is maintained, but RAM is refreshed.
Select Suspend Disabled to use power-reduced mode. Power will only be supplied
to limited components (such as RAMs) to maintain the most critical functions of the
system. The options are S1 (CPU Stop Clock), and Suspend Disabled.

NUMA (NON-Uniform Memory Access)

Select Enabled to enable the Non-Uniform Memory Access ACPI support. The op­tions are Enabled and Disabled.

High Precision Event Timer

Select Enabled to activate the High Precision Event Timer (HPET) that produces
periodic interrupts at a much higher frequency than a Real-time Clock (RTC) does
in synchronizing multimedia streams, providing smooth playback, reducing the de­pendency on other timestamp calculation devices, such as an x86 RDTSC Instruc-

7-21

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

tion embedded in the CPU. The High Performance Event Timer is used to replace
the 8254 Programmable Interval Timer. The options are Enabled and Disabled.

Trusted Computing (A vailable when a TPM device is detected
by the BIOS)

Confi guration

TPM Support

When this feature is set to Enabled, and the onboard TPM is also set to Enabled,
you can use TPM support to improve data integrity and network security for your
system. The options are Enabled and Disabled.

TPM State

Select Enabled to enable TPM security settings to improve data integrity and
network security. The options are Disabled and Enabled.

Pending Operation

Use this item to schedule an operation for the security device. The options are

None, Enable Take Ownership, Disable Take Ownership, and TPM Clear.

Note: Upon system reset, the computer will reboot in order to execute the

pending operation and change the state of the security device.

Current Status Information: This item displays current TPM status.

TPM Enable Status

This item indicates if TPM is currently enabled or disabled.

TPM Active Status

This item indicates if TPM is currently active or not.

TPM Owner Status

This item displays the status of TPM Ownership.

ME Subsystem

Intel ME Subsystem Confi guration

This feature displays information on the Intel Management Engine subsystem:

• ME BIOS Interface Version

• ME Version

7-22

7-4 Event Logs

This submenu allows the user to confi gure Event Log settings.

Change SMBIOS Event Log Settings

This feature allows the user to confi gure SMBIOS Event settings.

Chapter 7: BIOS

Enabling/Disabling Options

SMBIOS Event Log

Select Enabled to enable SMBIOS (System Management BIOS) event logging dur­ing system boot. The options are Enabled and Disabled.

Runtime Error Logging Support

Select Enabled to support runtime error logging. The options are Enabled and
Disabled.

Memory Correctable Error Threshold

Use this feature to enter the threshold value for correctable memory errors. The
default setting is 10.

PCI Error Logging Support

Select Enabled to support error event logging for PCI slots. The options are Enabled
and Disabled.

Erasing Settings

7-23

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

Erase Event Log

Select Enabled to erase the SMBIOS (System Management BIOS) Event Log, which
is completed before an event logging is initialized upon system reboot. The options
are No, Yes, next reset, and Yes, every reset.

When Log is Full

Select Erase Immediately to immediately erase SMBIOS error event logs that ex­ceed the limit when the SMBIOS event log is full. Select Do Nothing for the system
to do nothing when the SMBIOS event log is full. The options are Do Nothing and
Erase Immediately.

SMBIOS Event Log Standard Settings

Log System Boot Event
Select Enabled to log system boot events. The options are Disabled and Enabled.

MECI (Multiple Event Count Increment)

Enter the increment value for the multiple event counter. Enter a number between
1 to 255. The default setting is 1.

METW (Multiple Event Count Time Window)

This item allows the user to decide how long (in minutes) should the multiple event
counter wait before generating a new event log. Enter a number between 0 to 99.
The default setting is 60.

View SMBIOS Event Log

This item displays SMBIOS envent log.

7-24

Chapter 7: BIOS

7-5 IPMI

Use this feature to confi gure Intelligent Platform Management Interface (IPMI)
settings.

IPMI Firmware Revision

This item indicates the IPMI fi rmware revision used in your system.

IPMI Status

This item indicates the status of the IPMI fi rmware installed in your system.

System Event Log

Enabling/Disabling Options

SEL Components

Select Enabled for all system event logging at bootup. The options are Enabled
and Disabled.

Erasing Settings

Erase SEL

Select Yes, On next reset to erase all system event logs upon next system reboot.
Select Yes, On every reset to erase all system event logs upon each system reboot.
Select No to keep all system event logs after each system reboot. The options are
No, Yes, On next reset, and Yes, On every reset.

7-25

SUPERSERVER 6017R-73THDP+/6017R-73HDP+ User's Manual

When SEL is Full

This feature allows the user to decide what the BIOS should do when the system
event log is full. Select Erase Immediately to erase all events in the log when the
system event log is full. The options are Do Nothing and Erase Immediately.

BMC Network Confi guration

LAN Channel 1: This feature is used to confi gure the settings for LAN1 Port.

IPMI LAN Selection: This item displays the current IPMI Selection setting.

IPMI Network Line Status: This item displays the status of the current IPMI

network connection line.

Update IPMI LAN Confi guration

This feature allows the BIOS to implement any IP/MAC address changes at the next
system boot. If the option is set to Yes, any changes made to the settings below will
take effect at the next system reboot. The options are No and Yes.

Confi guration Address Source

Use this feature to select the source of the IP address for this computer. If Static is
selected, you will need to know the IP address of this computer and enter it to the
system manually in the fi eld. If DHCP is selected, the BIOS will search for a DHCP
(Dynamic Host Confi guration Protocol) server in the network that it is attached to
and request the next available IP address for this computer. The options for are
DHCP and Static. The following items are assigned IP addresses automatically if
DHCP is selected, or can be confi gured manually if Static is selected.

Station IP Address

This item displays the Station IP address for this computer . This should be in decimal
and in dotted quad form (i.e., 192.168.10.253).

Subnet Mask

This item displays the sub-network that this computer belongs to. The value of each
three-digit number separated by dots should not exceed 255.

Station MAC Address

This item displays the Station MAC address for this computer. Mac addresses are
6 two-digit hexadecimal numbers.

Gateway IP Address

This item displays the Gateway IP address for this computer. This should be in
decimal and in dotted quad form (i.e., 192.168.10.253).

7-26