Supero SuperServer 5013G-6, SuperServer 5013G-i User Manual

®

SUPER

SUPERSERVER 5013G-6/5013G-i

USER’S MANUAL

Revision 1.0b

The information in this User’s Manual has been carefully reviewed and is believed to be
accurate. The vendor assumes no responsibility for any inaccuracies that may be
contained in this document, makes no commitment to update or to keep current the
information in this manual, or to notify any person or organization of the updates.

Please
Note: For the most up-to-date version of this manual, please see our
web site at www.supermicro.com.

SUPERMICRO COMPUTER reserves the right to make changes to the product described in
this manual at any time and without notice. This product, including software, if any, and
documentation may not, in whole or in part, be copied, photocopied, reproduced, translated
or reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM
THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR
SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED
OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING,
INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR
DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of
Santa Clara shall be the exclusive venue for the resolution of any such disputes.
Supermicro's total liability for all claims will not exceed the price paid for the hardware
product.

Unless you request and receive written permission from SUPER MICRO COMPUTER, you
may not copy any part of this document.

Information in this document is subject to change without notice. Other products and
companies referred to herein are trademarks or registered trademarks of their respective
companies or mark holders.

Copyright © 2005 by SUPER MICRO COMPUTER INC.
All rights reserved.

Printed in the United States of America

Preface

About This Manual

This manual is written for professional system integrators and PC techni­cians. It provides information for the installation and use of the Super­Server 5013G-6/5013G-i. Installation and maintainance should be performed
by experienced technicians only.

The SuperServer 5013G-6/5013G-i is an economic single processor 1U
rackmount server based on the SC810 1U rackmount server chassis and
either the Super P4SGR (for the 5013G-6) or the P4SGE (for the 5013G-i)
mainboard. The P4SGR/P4SGE mainboard supports single Intel® PentiumTM 4
processors of up to 3.06 GHz in 478-pin microPGA sockets.

Manual Organization

Chapter 1: Introduction

The first chapter provides a checklist of the main components included with
the server system and describes the main features of the Super P4SGR
and P4SGE mainboards and the SC810 chassis.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer
5013G-6/5013G-i into a rack and check out the server configuration prior to
powering up the system. If your server was ordered without the proces­sor and memory components, this chapter will refer you to the appropriate
sections of the manual for their installation.

Chapter 3: System Interface

Refer to this chapter for details on the system interface, which includes the
functions and information provided by the control panel on the chassis as
well as other LEDs located throughout the system.

iii

Preface

SUPERSERVER 5013G-6/5013G-i Manual

iv

Chapter 4: System Safety

You should thoroughly familiarize yourself with this chapter for a general
overview of safety precautions that should be followed when installing and
servicing the SuperServer 5013G-6/5013G-i.

Chapter 5: Advanced Motherboard Setup

Chapter 5 provides detailed information on the P4SGR and P4SGE
motherboards, including the locations and functions of connectors, headers
and jumpers. Refer to this chapter when adding or removing processors or
main memory and when reconfiguring the motherboard.

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the SC810 1U rackmount
server chassis. You should follow the procedures given in this chapter
when installing, removing or reconfiguring SCSI or peripheral drives and
when replacing system power supply units and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed
information on running the CMOS Setup Utility.

Appendix A: BIOS Error Beep Codes and Messages

Appendix B: Post Diagnostic Error Messages

Appendix C: System Specifications

v

Preface

Notes

SUPERSERVER 5013G-6/5013G-i Manual

vi

Table of Contents

Preface

About This Manual ...................................................................................................... iii

Manual Organization ................................................................................................... iii

Chapter 1: Introduction

1-1 Overview ......................................................................................................... 1-1

1-2 Mainboard Chassis Features ....................................................................... 1-2

1-3 Server Chassis Features.............................................................................. 1-5

1-4 Contacting Supermicro .................................................................................. 1-7

Chapter 2: Server Installation

2-1 Overview ......................................................................................................... 2-1

2-2 Unpacking the SuperServer 5013G-6/5013G-i .......................................... 2-1

2-3 Preparing for Setup ....................................................................................... 2-1

Choosing a Setup Location .................................................................... 2-2

Rack Precautions ..................................................................................... 2-2

Server Precautions.................................................................................. 2-2

Rack Mounting Considerations .............................................................. 2-3

2-4 Installing the SuperServer 5013G-6/5013G-i into a Rack ....................... 2-4

Identifying the Sections of the Rack Rails .......................................... 2-4

Installing the Chassis Rails ..................................................................... 2-5

Installing the Rack Rails .......................................................................... 2-5

Installing the Server into the Rack ........................................................ 2-6

Installing the Server into a Telco Rack ................................................ 2-7

2- 5 Checking the Motherboard Setup ................................................................ 2-8

2-6 Checking the Drive Bay Setup ................................................................... 2-11

Chapter 3: System Interface

3-1 Overview ......................................................................................................... 3-1

3- 2 Control Panel Buttons .................................................................................... 3-1

Reset.......................................................................................................... 3-1

Power ........................................................................................................ 3-1

3-3 Control Panel LEDs ........................................................................................ 3-2

Overheat ................................................................................................... 3-2

NIC2 ............................................................................................................ 3-2

NIC1 ............................................................................................................ 3-2

HDD ............................................................................................................ 3-2

Power ........................................................................................................ 3-3

3- 4 SCSI Drive Carrier LEDs (5013G-6) ........................................................... 3-3

3- 5 Motherboard LEDs.......................................................................................... 3-3

Chapter 4: System Safety

4-1 Electrical Safety Precautions ........................................................................ 4-1

4-2 General Safety Precautions .......................................................................... 4-2

4- 3 ESD Precautions.............................................................................................. 4-3

4-4 Operating Precautions .................................................................................... 4-4

Chapter 5: Advanced Motherboard Setup

5-1 Handling the P4SGR/P4SGE Motherboard ................................................... 5-1

5- 2 Motherboard Installation ................................................................................. 5-2

5-3 Connecting Cables .......................................................................................... 5-3

Connecting Data Cables .......................................................................... 5-3

Connecting Power Cables....................................................................... 5-3

Connecting the Control Panel ................................................................. 5-3

5- 4 I/O Ports ............................................................................................................ 5-4

5-5 Installing Processors ...................................................................................... 5-5

5- 6 Installing Memory............................................................................................. 5-7

5- 7 Adding PCI Cards ............................................................................................ 5-8

P4SGR/P4SGE Layout .............................................................................. 5-9

P4SGR/P4SGE Quick Reference .......................................................... 5-10

5-8 Connector Definitions ................................................................................... 5-11

Power Supply Connectors ................................................................... 5-11

PWR_ON Connnector ............................................................................. 5-11

Reset Connector ..................................................................................... 5-12

Power Fail LED ....................................................................................... 5-12

Overheat Led (OH)................................................................................ 5-12

NIC2 LED .................................................................................................. 5-12

NIC1 LED .................................................................................................. 5-12

HDD LED ................................................................................................... 5-13

Power LED ............................................................................................... 5-13

NMI Button ................................................................................................ 5-13

IR Connector............................................................................................5-13

Serial Ports ............................................................................................. 5-13

CD Header................................................................................................ 5-14

Fan Headers ............................................................................................5-14

Chassis Intrusion .................................................................................... 5-14

Overheat LED (JOH1) ............................................................................ 5-14

vii

Table of Contents

SUPERSERVER 5013G-6/5013G-i Manual

viii

ATX PS/2 Keyboard and Mouse Ports ................................................5-15

Universal Serial Bus.............................................................................. 5-15

Wake-On-LAN ......................................................................................... 5-15

Wake-On-Ring ......................................................................................... 5-16

5- 9 Jumper Settings ............................................................................................. 5-16

Explanation of Jumpers ......................................................................... 5-16

CMOS Clear.............................................................................................. 5-16

USB Wake-Up..........................................................................................5-17

Watch Dog Enable/Disable .................................................................... 5-17

Front Side Bus Speed ........................................................................... 5-17

Keyboard Wake-Up................................................................................. 5-18

LAN1 Enable/Disable .............................................................................. 5-18

LAN2 Enable/Disable .............................................................................. 5-18

SCSI Enable/Disable................................................................................ 5-19

SCSI Termination ..................................................................................... 5-19

Chassis/Overheat Fan Select ...............................................................5-19

5-10 Parallel Port/Floppy/Hard Disk/SCSI/AGP Connections ........................... 5-20

Parallel Port .............................................................................................. 5-20

Floppy Connector ................................................................................... 5-21

IDE Connectors ...................................................................................... 5-21

Ultra160 SCSI Connectors ..................................................................... 5-22

4xAGP Slot ............................................................................................... 5-23

Chapter 6: Advanced Chassis Setup

6-1 Static-Sensitive Devices ................................................................................ 6-1

6-2 Control Panel .................................................................................................... 6-2

6-3 System Fans .................................................................................................... 6-3

System Fan Failure .................................................................................. 6-3

Replacing System Cooling Fans ............................................................ 6-3

6- 4 Drive Bay Installation/Removal ...................................................................... 6-4

Accessing the Drive Bays ..................................................................... 6-4

SCSI Drive Installation............................................................................. 6-5

IDE Drive Installation................................................................................ 6-7

CD-ROM and Floppy Drive Installation ................................................. 6-8

6-5 Power Supply .................................................................................................. 6-9

Power Supply Failure ............................................................................. 6-9

Replacing the Power Supply ................................................................. 6-9

Table of Contents

ix

Chapter 7: AwardBIOS

7- 1 Introduction....................................................................................................... 7-1

7- 2 Running Setup.................................................................................................. 7-2

7- 3 Main BIOS Setup.............................................................................................. 7-2

The Main BIOS Setup Menu .................................................................... 7-3

7-4 Advanced BIOS Setup .................................................................................... 7-6

7-4.1 Advanced BIOS Features .......................................................... 7-6

7-4.2 Advanced Chipset Features ...................................................... 7-9

7-4.3 Integrated Peripherals ............................................................... 7-13

7-4.4 Hardware Monitors.................................................................... 7-16

7-4.5 Processor Features .................................................................. 7-17

7-5 PCI/PnP Configurations ................................................................................. 7-18

7-6 Power.............................................................................................................. 7-20

7- 7 Boot ................................................................................................................. 7-23

7-8 Security ........................................................................................................... 7-25

7-9 Exit ................................................................................................................... 7-26

Appendices:

Appendix A: BIOS POST Messages ..................................................................... A-1

Appendix B: BIOS POST Codes ............................................................................. B-1

Appendix C: System Specifications ...................................................................... C-1

SUPERSERVER 5013G-6/5013G-i User's Manual

x

Notes

Chapter 1

Introduction

1-1 Overview

The Supermicro SuperServer 5013G-6/5013G-i is an economical single pro­cessor, 1U rackmount server with state-of-the-art features. The 5013G-6/
5013G-i is comprised of two main subsystems: the SC810 1U rackmount
chassis and the P4SGR (5013G-6) or P4SGE (5013G-i) single 478-pin
Pentium 4 microPGA processor mainboard. Please refer to our web site for
information on operating systems that have been certified for use with the
5013G-6/5013G-i (www.supermicro.com).

In addition to the mainboard and chassis, various hardware components
may have been included with your SuperServer 5013G-6/5013G-i, as listed
below.

 One CPU heatsink (SNK-032)

 One (1) 3.5" floppy drive

 One (1) slim CD-ROM drive

 One (1) SCA SCSI backplane (5013G-6 only)

 Two (2) SCA SCSI drive carriers (5013G-6 only)

 SCSI Accessories(5013G-6 only):

One (1) internal 68-pin Ultra160 SCSI cable for SCA SCSI backplane

One (1) set of SCSI driver diskettes

One (1) SCSI manual

 One (1) 5V 32-bit, 33 MHz PCI slot riser card (CSE-RR32-1U)

 Rackmount hardware (with screws):

Two (2) rack rail assemblies

Six (6) brackets for mounting the rack rails in a rack/telco rack

 One (1) CD containing drivers and utilities

 SuperServer 5013G-6/5013G-i User's Manual

Chapter 1: Introduction

1-1

SUPERSERVER 5013G-6/5013G-i Manual

1-2

1-2 Mainboard Features

At the heart of the SuperServer 5013G-6/5013G-i lies the P4SGR/P4SGE, a
single processor motherboard designed to provide maximum performance.
Below are the main features of the P4SGR/P4SGE. See Figure 1-1 for a
block diagram of the 845GE chipset.

Chipset Overview

Intel’s 845GE chipset is made up of two main components:

The Graphics Memory Controller Hub (GMCH)

The I/O Controller Hub (ICH4)

Graphics Memory Controller Hub (GMCH)

The GMCH includes the host (CPU) interface, memory interface, ICH4 inter­face and 4xAGP interface for the 845GE chipset. It contains advanced
power management logic and supports a single channel of DDR SDRAM.
The AGP 2.0 interface supports 4x data transfers and operates at a peak
bandwidth of 1.6 GB/sec.

An external graphics accelerator card is not required due to the integrated
graphics in the 845GE chipset. (If the system BIOS detects an external
AGP device, it will disable the integrated graphics.) The integrated graphics
controller delivers 3D, 2D and video capabilities, including video
conferencing applications. The controller does not utlilize local memory, but
accesses graphics data located in system memory at speeds of up to 2.1
GB/s (DDR-266). It also includes a cache controller to avoid frequent
memory fetches of recently accessed texture data.

I/O Controller Hub (ICH4)

The ICH4 is a fourth-generation I/O Controller Hub subsystem that integrates
many of the input/output functions of the 845GE chipset, including a two­channel ATA100 Bus Master IDE controller. The ICH4 also interfaces with
the PCI cards, the AC'97 Audio CODEC and the various communications
ports. Nearly all communications between the GMCH and the ICH4 takes
place over the hub Interface, which is a 66 MHz/266 MB/s bus.

Chapter 1: Introduction

1-3

Processors

The P4SGR/P4SGE supports single 478-pin Pentium 4 microPGA processors
at up to 3.06 GHz at a front side (system) bus speed of 533 or 400 MHz.
Please refer to the support section of our web site for a complete listing of
supported processors (http://www.supermicro.com/TechSupport.htm).

Memory

The P4SGR/P4SGE has two (2) 184-pin DIMM sockets that can support up to
2 GB of non-ECC unbuffered PC2700/2100 (DDR-333/266) low-profile
SDRAM modules. Module sizes of 128 MB, 256 MB, 512 MB and 1 GB may
be used to populate the DIMM slots.

Onboard SCSI (5013G-6 only)

Onboard SCSI is provided with an Adaptec AIC-7899 SCSI controller chip,
which supports dual channel, Ultra160 SCSI at a burst throughput rate of
160 MB/sec for each channel. The P4SGR provides two SCSI ports: one
internal 68-pin LVD Ultra160 connector (on Channel A) and one external/
internal (shared) 68-pin Ultra160 SCSI connector (channel B).

PCI Expansion Slots

The P4SGR/P4SGE has six 32-bit, 33 MHz PCI slots available. One riser
card is included with the system for use with 32-bit PCI cards.

Network Interface Controllers (NIC)

The P4SGR/P4SGE supports two Gb LAN ports (or Network Interface con­trollers -NIC) based on Intel's 82540EM Ethernet controller chip.

Onboard Controllers/Ports

An onboard IDE controller supports one floppy drive and up to four UDMA/
100 hard drives or ATAPI devices. Onboard I/O ports include one COM port,
one parallel port, two USB ports, PS/2 mouse and keyboard ports, a VGA
(graphics) port and two LAN (NIC) ports.

SUPERSERVER 5013G-6/5013G-i Manual

1-4

Other Features

Other onboard features that promote system health include eight voltage
monitors, a chassis intrusion header, auto-switching voltage regulators,
chassis and CPU overheat sensors, virus protection and BIOS rescue.

Figure 1-1. 845G Chipset: System Block Diagram

Note: This is a general block diagram. See Chapter 5 for details.

GMCH

FC-PG A

400/533 MHz System Bus

333 MHz Bus

Dual Channe l

IDE (PRI/SEC)

Pentium 4 Processor

(PGA 478)

DDR SDRAM

PCI Slots

USB

Ports (6)

Mb LAN

Port

ICH4

133 MB/s PCI Bus

4xAGP

Flash BIOS

FW H

1.06 GB/s

266 MB/s Hub

Audio

CODEC

On ch ip

VGA

AC'97

USB 2.0

UDMA/100

LPC I/O

LPC B us

Keyboard/Mouse

Floppy Drive

Serial P orts

Parallel Port

Game Port

Monitor

Chapter 1: Introduction

1-5

1-3 Server Chassis Features

The SuperServer 5013G-6/5013G-i is a scaleable 1U rackmount server plat­form designed with some of today's most state-of-the-art features. The
following is a general outline of the main features of the SC810 chassis.

System Power

When configured as a SuperServer 5013G-6/5013G-i, the SC810 chassis
includes a single 250W power supply.

SCSI Subsystem (5013G-6 only)

The SCSI subsystem on the 5013G-6 supports two 80-pin SCA Ultra160
SCSI hard drives. (Standard 1" drives are supported. SCA = Single Con­nection Attachment.) The SCSI drives are connected to an SCA backplane
that provides power, bus termination and configuration settings. The SCSI
drives are also hot-swap units.

Control Panel

The SC810's control panel provides important system monitoring and control
information. LEDs indicate power on, network activity, hard disk drive ac­tivity and system overheat conditions. The control panel also includes a
main power button and a system reset button.

Rear I/O Panel

The SC810 is a 1U rackmount chassis. Its I/O panel provides one mother­board expansion slot, one COM port (another is internal), two USB ports
(5013G-6 only), PS/2 mouse and keyboard ports, a graphics port and two
Ethernet ports. (See Figure 1-2.)

SUPERSERVER 5013G-6/5013G-i Manual

1-6

Figure 1-2. Rear I/O Panel

Cooling System

The SC810 chassis has an innovative cooling design that includes a 10-cm
blower system cooling (intake) fan and one optional 4-cm fan that can be
installed in the midsection of the chassis. The blower fan plugs into a
chassis fan header on the motherboard and operates at full rpm continu­ously. If it breaks down, the ambient air temperature inside the chassis will
rise and activate an overheat LED.

Chapter 1: Introduction

1-7

1-4 Contacting Supermicro

Headquarters

Address: SuperMicro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)
Web Site: www.supermicro.com

Europe

Address: SuperMicro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Asia-Pacific

Address: SuperMicro, Taiwan

4F, No. 232-1, Liancheng Rd.

Chung-Ho 235, Taipei County

Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [e-mail]
Tel: [phone], ext.132 or 139

SUPERSERVER 5013G-6/5013G-i Manual

1-8

Notes

Chapter 2: Server Installation

2-1

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your SuperServer
5013G-6/5013G-i up and running. Following the steps in the order given
should enable you to have the system operational within a minimal amount
of time. This quick setup assumes that your 5013G-6/5013G-i system has
come to you with the processor and memory preinstalled. If your system is
not already fully integrated with a motherboard, processor, system memory
etc., please turn to the chapter or section noted in each step for details on
installing specific components.

2-2 Unpacking the SuperServer 5013G-6/5013G-i

You should inspect the box the SuperServer 5013G-6/5013G-i was shipped
in and note if it was damaged in any way. If the server itself shows
damage, you should file a damage claim with the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the SuperServer
5013G-6/5013G-i. It should be situated in a clean, dust-free area that is well
ventilated. Avoid areas where heat, electrical noise and electromagnetic
fields are generated. You will also need it placed near a grounded power
outlet. Read the Rack and Server Precautions in the next section.

2-3 Preparing for Setup

The box the SuperServer 5013G-6/5013G-i was shipped in should include
two sets of rail assemblies, two rail mounting brackets and the mounting
screws you will need to install the system into the rack. Follow the steps
in the order given to complete the installation process in a minimal amount of
time. Please read this section in its entirety before you begin the installation
procedure outlined in the sections that follow.

2-2

SUPERSERVER 5013G-6/5013G-i Manual

Choosing a Setup Location

- Leave enough clearance in front of the rack to enable you to open

the front door completely (~25 inches).

- Leave approximately 30 inches of clearance in the back of the rack

to allow for sufficient airflow and ease in servicing.

Rack Precautions

- Ensure that the leveling jacks on the bottom of the rack are fully

extended to the floor with the full weight of the rack resting on them.

- In a single rack installation, stabilizers should be attached to the rack.

- In multiple rack installations, the racks should be coupled together.

- Always make sure the rack is stable before extending a component

from the rack.

- You should extend only one component at a time - extending two or

more simultaneously may cause the rack to become unstable.

Server Precautions

- Review the electrical and general safety precautions in Chapter 4.

- Determine the placement of each component in the rack before you

install the rails.

- Install the heaviest server components on the bottom of the rack

first, and then work up.

- Use a regulating uninterruptible power supply (UPS) to protect the
server from power surges, voltage spikes and to keep your
system operating in case of a power failure.

- Allow the power supply units and hot plug SCSI drives (5013G-6) to

cool before touching them.

- Always keep the rack's front door and all panels and components on

the servers closed when not servicing to maintain proper cooling.

!

!

Warnings and Precautions!

Chapter 2: Server Installation

2-3

Rack Mounting Considerations

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating
temperature of the rack environment may be greater than the ambient tem­perature of the room. Therefore, consideration should be given to installing
the equipment in an environment compatible with the manufacturer’s maxi­mum rated ambient temperature (Tmra).

Reduced Airflow

Equipment should be mounted into a rack so that the amount of airflow
required for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition
does not arise due to uneven mechanical loading.

Circuit Overloading

Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might

have on overcurrent protection and power supply wiring. Appropriate consid­eration of equipment nameplate ratings should be used when addressing this
concern.

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack
itself should be grounded. Particular attention should be given to power
supply connections other than the direct connections to the branch circuit
(i.e. the use of power strips, etc.).

2-4

SUPERSERVER 5013G-6/5013G-i Manual

2-4 Installing the SuperServer 5013G-6/5013G-i into

a Rack

This section provides information on installing the SuperServer 5013G-6/
5013G-i into a rack unit. If the5013G-6/5013G-i has already been mounted
into a rack, you can skip ahead to Sections 2-5 and 2-6. There are a
variety of rack units on the market, which may mean the assembly proce­dure will differ slightly. The following is a guideline for installing the 5013G­6/5013G-i into a rack with the rack rails provided with the system. You
should also refer to the installation instructions that came with the rack unit
you are using.

Identifying the Sections of the Rack Rails

You should have received two rack rail assemblies with the SuperServer
5013G-6/5013G-i. Each of these assemblies consist of two sections: an
inner fixed chassis rail that secures to the 5013G-6/5013G-i (A) and an
outer fixed rack rail that secures directly to the rack itself (B). A sliding rail
guide sandwiched between the two should remain attached to the fixed
rack rail (see Figure 2-1). The A and B rails must be detached from each
other to install.

To remove the fixed chassis rail (A), pull it out as far as possible - you
should hear a "click" sound as a locking tab emerges from inside the rail
assembly and locks the inner rail. Then depress the locking tab to pull the
inner rail completely out. Do this for both the left and right side rack rail
assemblies.

Figure 2-1. Identifying the Sections of the Rack Rails

Mounting Holes

A

Locking Tab

B

Chapter 2: Server Installation

2-5

Installing the Chassis Rails

Position the fixed chassis rail sections you just removed along the side of
the 5013G-6/5013G-i chassis making sure the five screw holes line up.
Note that these two rails are left/right specific. Screw the rail securely to
the side of the chassis (see Figure 2-2). Repeat this procedure for the
other rail on the other side of the chassis. You will also need to attach the
rail brackets when installing into a telco rack.

Locking Tabs: As you have seen, both chassis rails have a locking tab,
which serves two functions. The first is to lock the server into place
when installed and pushed fully into the rack, which is its normal position.
Secondly, these tabs also lock the server in place when fully extended
from the rack. This prevents the server from coming completely out of
the rack when you pull it out for servicing.

Figure 2-2. Installing Chassis Rails

Installing the Rack Rails

Determine where you want to place the SuperServer 5013G-6/5013G-i in
the rack (see Rack and Server Precautions in Section 2-3). Position the
fixed rack rail/sliding rail guide assemblies at the desired location in the
rack, keeping the sliding rail guide facing the inside of the rack. Screw the

2-6

SUPERSERVER 5013G-6/5013G-i Manual

Figure 2-3. Installing the Server into a Rack

Installing the Server into the Rack

You should now have rails attached to both the chassis and the rack
unit. The next step is to install the server into the rack. Do this by
lining up the rear of the chassis rails with the front of the rack rails.
Slide the chassis rails into the rack rails, keeping the pressure even on
both sides (you may have to depress the locking tabs when inserting).
See Figure 2-3.

When the server has been pushed completely into the rack, you should
hear the locking tabs "click". Finish by inserting and tightening the
thumbscrews that hold the front of the server to the rack.

assembly securely to the rack using the brackets provided. Attach the
other assembly to the other side of the rack, making sure that both are at
the exact same height and with the rail guides facing inward.

Chapter 2: Server Installation

2-7

Figure 2-4. Installing the Server into a Telco Rack

Installing the Server into a Telco Rack

If you are installing the SuperServer 5013G-6/5013G-i into a Telco type
rack, follow the directions given on the previous pages for rack installation.
The only difference in the installation procedure will be the positioning of
the rack brackets to the rack. They should be spaced apart just enough to
accomodate the width of the telco rack.

2-8

SUPERSERVER 5013G-6/5013G-i Manual

2-5 Checking the Motherboard Setup

After you install the 5013G-6/5013G-i in the rack, you will need to open the
unit to make sure the motherboard is properly installed and all the connec­tions have been made.

1. Accessing the inside of the 5013G-6/5013G-i (Figures 2-5a/2-5b)

First, release the retention screws that secure the unit to the rack.
Grasp the two handles on either side and pull the unit straight out until it
locks (you will hear a "click"). Next, depress the two buttons on the top
of the chassis to release the top cover. There is a large rectangular
recess in the middle front of the top cover to help you push the cover
away from you until it stops. You can then lift the top cover from the
chassis to gain full access to the inside of the server.

2. Check the CPU (processor)

You may have one processor already installed in the motherboard. Each
processor should have its own heatsink attached. See Chapter 5 for
instructions on processor installation.

3. Check the system memory

Your 5013G-6/5013G-i server system may have come with system
memory already installed. Make sure all DIMMs are fully seated in their
slots. For details on adding system memory, refer to Chapter 5.

4. Installing add-on cards

If desired, you can install an add-on card to the system. See Chapter 5
for details on installing a PCI add-on card.

5. Check all cable connections and airflow

Make sure all power and data cables are properly connected and not
blocking the airflow. See Chapter 5 for details on cable connections.
Also, check the air seals for damage. The air seals are located under
the blower fan and beneath the frame cross section that separates the
drive bay area from the motherboard area of the chassis.

Note: Make sure that the air seals are properly installed.

Chapter 2: Server Installation

2-9

Figure 2-5a.

Accessing the Inside of the SuperServer 5013G-6

(with SCSI drive removed)

2-10

SUPERSERVER 5013G-6/5013G-i Manual

Figure 2-5b.

Accessing the Inside of the SuperServer 5013G-i

(with IDE drive removed)

Chapter 2: Server Installation

2-11

2-6 Checking the Drive Bay Setup

Next, you should check to make sure the peripheral drives and the SCSI
drives and SCA backplane (5013G-6 only) or IDE drives (5013G-i only)
have been properly installed and all connections have been made.

1. Accessing the drive bays

All drives can be accessed from the front of the server. For servicing
the CD-ROM and floppy drives, you will need to remove the top chassis
cover. The SCSI disk drives can be installed and removed from the front
of the chassis without removing the top chassis cover.

2. Installing a CD-ROM and floppy disk drives

Refer to Chapter 6 if you need to reinstall a CD-ROM and/or floppy disk
drive to the system.

3. Check the SCSI disk drives (5013G-6)

Depending upon your system's configuration, your system may have one
or two SCSI drives already installed. If you need to install SCSI drives,
please refer to the appropriate section in Chapter 6.

4. Check the IDE disk drives (5013G-i)

Depending upon your system's configuration, your system may have one
or two IDE hard drives already installed. If you need to install an IDE hard
drive, please refer to the appropriate section in Chapter 6.

5. Check the airflow

Airflow is provided by a 10-cm input fan and one (optional) 4-cm cooling
fan. The system component layout was carefully designed to promote
sufficient airflow through the small 1U rackmount space. Also note that
all power and data cables have been routed in such a way that they do
not block the airflow generated by the fans.

6. Supplying power to the system

The last thing you must do is to provide input power to the system. Plug
the power cord from the power supply unit into a high-quality power
strip that offers protection from electrical noise and power surges. It is
recommended that you use an uninterruptible power supply (UPS).

2-12

SUPERSERVER 5013G-6/5013G-i Manual

Notes