Supero SUPER SERVER 5013C-MT User Manual

®

SUPER

SUPERSERVER 5013C-MT

USER’S MANUAL

Revision 1.0

The information in this User’s Manual has been carefully reviewed and is believed to be
accurate. The vendor assumes no responsibility for any inaccuracies that may be
contained in this document, makes no commitment to update or to keep current the
information in this manual, or to notify any person or organization of the updates.

Please
Note: For the most up-to-date version of this manual, please see our
web site at www.supermicro.com.

SUPERMICRO COMPUTER reserves the right to make changes to the product described in
this manual at any time and without notice. This product, including software, if any, and
documentation may not, in whole or in part, be copied, photocopied, reproduced, translated
or reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM
THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR
SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED
OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING,
INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR
DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of
Santa Clara shall be the exclusive venue for the resolution of any such disputes.
Supermicro's total liability for all claims will not exceed the price paid for the hardware
product.

Unless you request and receive written permission from SUPER MICRO COMPUTER,
you may not copy any part of this document.

Information in this document is subject to change without notice. Other products and
companies referred to herein are trademarks or registered trademarks of their respective
companies or mark holders.

Copyright © 2004 by SUPER MICRO COMPUTER INC.
All rights reserved.

Printed in the United States of America

Preface

About This Manual

This manual is written for professional system integrators and PC technicians.
It provides information for the installation and use of the SuperServer 5013C-MT.
Installation and maintainance should be performed by experienced technicians
only.

The SuperServer 5013C-MT is a high-end single processor 1U rackmount server
based on the SC813MT-300C 1U rackmount server chassis and the Super
P4SCT+ motherboard. The P4SCT+ supports a single Intel® Pentium® 4 proces­sor of up to 3.40 GHz (processors must be 0.13 micron technology) and Intel®
Celeron® processors of up to 2.80 GHz.

Manual Organization

Chapter 1: Introduction

The first chapter provides a checklist of the main components included with the
server system and describes the main features of the Super P4SCT+ motherboard
and the SC813MT-300C chassis.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer
5013C-MT into a rack and check out the server configuration prior to powering up
the system. If your server was ordered without the processor and memory
components, this chapter will refer you to the appropriate sections of the manual
for their installation.

Chapter 3: System Interface

Refer to this chapter for details on the system interface, which includes the
functions and information provided by the control panel on the chassis as
well as other LEDs located throughout the system.

iii

Preface

SUPERSERVER 5013C-MT User's Manual

iv

Chapter 4: System Safety

You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 5013C-MT.

Chapter 5: Advanced Motherboard Setup

Chapter 5 provides detailed information on the P4SCT+ motherboard, including
the locations and functions of connectors, headers and jumpers. Refer to this
chapter when adding or removing processors or main memory and when
reconfiguring the motherboard.

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the SC813MT-300C 1U rackmount
server chassis. You should follow the procedures given in this chapter when
installing, removing or reconfiguring Serial ATA or peripheral drives and when
replacing system power supply units and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed
information on running the CMOS Setup Utility.

Appendix A: BIOS POST Messages

Appendix B: BIOS POST Codes

Appendix C: Software Installation

Appendix D: System Specifications

v

Preface

Notes

vi

Table of Contents

Preface

About This Manual ....................................................................................................... ii i

Manual Organization .................................................................................................... ii i

Chapter 1: Introduction

1-1 Overview ............................................................................................................ 1- 1

1-2 Motherboard Features ..................................................................................... 1-2

1- 3 Server Chassis Features ................................................................................ 1-5

1- 4 Contacting Supermicro ................................................................................... 1-7

Chapter 2: Server Installation

2-1 Overview ............................................................................................................ 2- 1

2-2 Unpacking the SuperServer 5013C-MT.......................................................... 2- 1

2- 3 Preparing for Setup ......................................................................................... 2-1

Choosing a Setup Location...................................................................... 2-2

Rack Precautions...................................................................................... 2-2

Server Precautions.................................................................................... 2-2

2-4 Installing the SuperServer 5013C-MT into a Rack....................................... 2-3

Identifying the Sections of the Rack Rails ............................................ 2-3

Installing the Rear Inner Rails ................................................................. 2-3

Installing the Rack Rails .......................................................................... 2-4

Installing the Server into the Rack ......................................................... 2- 5

Installing the Server into a Telco Rack .................................................. 2-6

2- 5 Checking the Motherboard Setup .................................................................. 2- 7

2-6 Checking the Drive Bay Setup....................................................................... 2-9

Chapter 3: System Interface

3-1 Overview ............................................................................................................ 3- 1

3-2 Control Panel Buttons..................................................................................... 3- 1

Reset.......................................................................................................... 3-1

Power ......................................................................................................... 3 -1

3- 3 Control Panel LEDs......................................................................................... 3-2

Overheat ..................................................................................................... 3 -2

NIC2 ............................................................................................................ 3- 2

NIC1 ............................................................................................................ 3- 2

HDD ............................................................................................................ 3-2

Power ......................................................................................................... 3 -3

SUPERSERVER 5013C-MT User's Manual

3- 4 Serial ATA Drive Carrier LEDs ....................................................................... 3-3

Chapter 4: System Safety

4-1 Electrical Safety Precautions......................................................................... 4- 1

4- 2 General Safety Precautions ........................................................................... 4-2

4-3 ESD Precautions ............................................................................................. 4-3

4- 4 Operating Precautions .................................................................................... 4-4

Chapter 5: Advanced Motherboard Setup

5- 1 Handling the P4SCT+ Motherboard ............................................................... 5-1

5- 2 Motherboard Installation.................................................................................. 5-2

5- 3 Connecting Cables .......................................................................................... 5 -3

Connecting Data Cables .......................................................................... 5-3

Connecting Power Cables ........................................................................ 5 -3

Connecting the Control Panel ................................................................. 5-3

5-4 I/O Ports ........................................................................................................... 5-4

5- 5 Installing Processors ...................................................................................... 5 - 5

5- 6 Installing Memory ............................................................................................ 5-7

5- 7 Adding PCI Cards ............................................................................................ 5-8

5- 8 Motherboard Details ........................................................................................ 5-9

P4SCT+ Layout ......................................................................................... 5-9

P4SCT+ Quick Reference ...................................................................... 5-10

5- 9 Connector Definitions .................................................................................... 5-11

Power Supply Connectors...................................................................... 5-11

PW_ON Connnector................................................................................ 5-11

Reset Connector ..................................................................................... 5-12

Overheat LED (OH) ................................................................................. 5-12

GLAN2 LED ............................................................................................. 5-12

GLAN1 LED ............................................................................................. 5-12

IDE LED ................................................................................................... 5-13

Power_LED Connector ........................................................................... 5-13

NMI Button............................................................................................... 5-13

SMB Header ............................................................................................ 5-13

IR Connector............................................................................................ 5-14

Serial Ports ............................................................................................. 5-14

Fan Headers ............................................................................................ 5-14

Chassis Intrusion .................................................................................... 5-15

Wake-On-LAN.......................................................................................... 5-15

Wake-On-Ring ......................................................................................... 5-15

vii

Table of Contents

viii

ATX PS/2 Keyboard and PS/2 Mouse Ports ....................................... 5-15

Universal Serial Bus ............................................................................... 5-16

GLAN1/2 (Ethernet) Ports...................................................................... 5-16

SATA LED (Marvell)................................................................................ 5-16

SATA LED (Intel) .................................................................................... 5-16

5-10 Jumper Settings............................................................................................. 5-17

Explanation of Jumpers.......................................................................... 5-17

CMOS Clear ............................................................................................ 5-17

Front Side Bus Speed............................................................................ 5-17

USB Wake-Up ......................................................................................... 5-18

Watch Dog Enable/Disable.................................................................... 5-18

Speaker Jumper ...................................................................................... 5-18

Keyboard Wake-Up ................................................................................. 5-19

GLAN2 Enable/Disable ........................................................................... 5-19

VGA Enable/Disable ............................................................................... 5-19

Keylock Enable/Disable ......................................................................... 5-19

5-11 Onboard Indicators ........................................................................................ 5-20

Standby Power LED ............................................................................... 5-20

5-12 Parallel Port/Floppy and Hard Drive Connections...................................... 5-21

Parallel Port Connector .......................................................................... 5-21

Floppy Connector .................................................................................... 5-22

IDE Connectors ....................................................................................... 5-22

Chapter 6: Advanced Chassis Setup

6- 1 Static-Sensitive Devices ................................................................................. 6-1

6- 2 Control Panel ................................................................................................... 6-2

6-3 System Fans.................................................................................................... 6- 3

System Fan Failure .................................................................................. 6-3

6-4 Drive Bay Installation/Removal ....................................................................... 6-3

Removing the Front Bezel ....................................................................... 6-3

Accessing the Drive Bays ....................................................................... 6-4

Serial ATA Drive Installation .................................................................... 6-4

CD-ROM Drive Installation ....................................................................... 6-6

6- 5 Power Supply................................................................................................... 6-7

Power Supply Failure ............................................................................... 6 -7

Replacing the Power Supply ................................................................... 6 -7

SUPERSERVER 5013C-MT User's Manual

Table of Contents

ix

Chapter 7: BIOS

7-1 Introduction....................................................................................................... 7-1

7- 2 Running Setup ................................................................................................. 7-2

7-3 Main BIOS Setup ............................................................................................ 7-2

7- 4 Advanced BIOS Setup .................................................................................... 7- 4

7-4.1 Advanced BIOS Features ............................................................. 7 -4

7-4.2 Advanced Chipset Control ............................................................ 7- 5

7-4.3 I/O Device Configuration ............................................................... 7- 7

7-4.4 PnP Configuration.......................................................................... 7-9

7-4.5 Console Redirection .................................................................... 7-10

7-4.6 Hardware Monitor......................................................................... 7-11

7-4.7 Processor and Clock Options .................................................... 7-12

7-5 Security .......................................................................................................... 7-13

7-6 Boot................................................................................................................. 7-14

7-7 Exit.................................................................................................................. 7-15

Appendices:

Ap pe n d i x A: B I O S P O S T Me s s a g es ....................................................................... A - 1

Appendix B: BIOS POST Codes ............................................................................. B- 1

Appendix C: Software Installation ........................................................................... C-1

Appendix D: System Specifications ....................................................................... D-1

x

Notes

SUPERSERVER 5013C-MT User's Manual

Chapter 1

Introduction

1-1 Overview

The Supermicro SuperServer 5013C-MT is a high-end single processor, 1U
rackmount server. The 5013C-MT is comprised of two main subsystems: the
SC813MT-300C chassis and the P4SCT+ motherboard. The P4SCT+ supports
a single 478-pin Intel Pentium 4 microPGA processor at up to 3.40 GHz with HT
(hyper-threading) technology (or single a Intel Celeron processor of up to 2.80
GHz) and up to 4 GB of ECC or non-ECC unbuffered DDR400/333/266 SDRAM
memory. Please refer to our web site for information on operating systems that
have been certified for use with the 5013C-MT (www.supermicro.com) and for
regular updates on supported processor speeds.

In addition to the motherboard and chassis, various hardware components may
have been included with the 5013C-MT, as listed below.

! One CPU heatsink (SNK-P0002)

! One (1) slim CD-ROM drive

! Serial ATA (SATA) Accessories:

One (1) internal SATA backplane (CSE-SATA-813)

Four (4) SATA cables (CBL-0074)

One (1) SATA LED cables (CBL-0069)

Four (4) SATA drive carriers (CSE-PT39)

! One (1) 3.3V 64-bit, 66 MHz PCI-X slot riser card (CSE-RR1U-X)

! Rackmount hardware (with screws):

Two (2) rack rail assemblies

Six (6) brackets for mounting the rack rails in a rack/telco rack

! One (1) CD containing drivers and utilities

! SuperServer 5013C-MT User's Manual

Chapter 1: Introduction

1-1

1-2

SUPERSERVER 5013C-MT User's Manual

1-2 Motherboard Features

At the heart of the SuperServer 5013C-MT lies the P4SCT+, a single processor
motherboard designed to provide maximum performance. Below are the main
features of the P4SCT+.

Chipset Overview

The P4SCT+ is based on Intel’s E7210 chipset (see Figure 1-1 for a block
diagram). The E7210 chipset is made up of two main components:

The Memory Controller Hub (MCH)

The I/O Controller Hub (6300ESB)

Memory Controller Hub (MCH)

The MCH controls the flow of data between the host (CPU) interface, the memory
interface and the I/O Controller Hub interface. It contains advanced power man­agement logic and supports dual-channel (interleaved) DDR memory, providing
bandwidth of up to 6.4 GB/s using DDR400 SDRAM. The MCH supports configu­rations of a 800 MHz FSB with a 400/333 memory interface, a 533 MHz FSB with
a 333/266 memory interface, and a 400 MHz FSB with a 266 MHz memory
interface.
The MCH supports 128 MB, 256 MB, 512 MB, 1 GB, x4, x8, and x16 DDR.
Maximum system memory supports up to 4.0 GB for dual-channel, ECC or Non­ECC unbuffered DDR. Registered and/or mixed-mode DIMMs are not supported.
For more information, please refer to Chapter 5.

I/O Controller Hub (6300ESB)

The 6300ESB ICH provides the I/O subsystem with access to the rest of the

system. It integrates a dual-channel Ultra ATA/100 bus master IDE controller, two
Serial ATA (SATA) host controllers, the SMBus 2.0 controller, the LPC/Flash BIOS
interface, the PCI-X (66MHz) 1.0 interface, the PCI 2.2 interface and the System
Management Controller.

Chapter 1: Introduction

1-3

Processors

The P4SCT+ supports a single Intel® Pentium® 4 processor of up to 3.40 GHz
with hyper-threading technology in a 478-pin microPGA socket (must be 0.13
micron technology) or single a Intel® Celeron® processor of up to 2.80 GHz.
Please refer to the support section of our web site for a complete listing of
supported processors (http://www.supermicro.com/support/).

Memory

The P4SCT+ has four (4) 184-pin DIMM sockets that can support up to 4 GB of
ECC or non-ECC unbuffered DDR400/333/266 SDRAM modules. (Memory oper­ates in a dual-channel, or interleaved configuration for increased performance.)
Low-profile memory modules are required for use in the 1U form factor of the
5013C-MT. Module sizes of 128 MB, 256 MB, 512 MB and 1 GB may be used
to populate the DIMM slots.

Serial ATA

A Serial ATA controller is incorporated into the E7210 chipset to provide a two­port Serial ATA subsystem.

PCI Expansion Slots

The P4SCT+ has two 32-bit, 33 MHz (5V) PCI slots and three 64-bit, 66 MHz
(3.3V) PCI-X slots. When incorporated into the 5013C-MT server system, one 64­bit, 66 MHz PCI-X slot is available with the use of a riser card, which supports
one full-height, full-length PCI card.

Ethernet Ports

The E7210 includes an on-chip Gb Ethernet controller and the P4SCT+ has an
additional Gb Ethernet controller to support a total of two Gigabit LAN ports.

1-4

SUPERSERVER 5013C-MT User's Manual

Onboard Controllers/Ports

An onboard IDE controller supports one floppy drive and up to four Ultra ATA 100
hard drives or ATAPI devices. Onboard I/O backpanel ports include one serial
COM port, one parallel port, four USB ports, PS/2 mouse and keyboard ports and
two GLAN (RJ45) ports.

Other Features

Other onboard features that promote system health include eight voltage moni­tors, a chassis intrusion header, auto-switching voltage regulators, chassis and
CPU overheat sensors, virus protection and BIOS rescue.

Figure 1-1 . Intel E7210 Chipset:

System Block Diagram

Note: This is a general block diagram. Please see Chapter 5 for details.

MCH

Processor 0

ICH

6300ES B

USB Ports

(4)

ATA/100
Ports (2 )

DIMM

DIMM

Dual-Channel DIMMs (4)

(DDR400/333/266)

CSA Gb Ethernet

Controller (66MHz)

SATA Ports

(2)

FWH

Printer H/W Monitor

ADDR

CTLR

DATA

3.2 GB/s

Hub A

64-bit/66 MHz

UDMA

100

SATA

USB 2.0

Serial PortFDDKB/Mouse

LPC I/O

PCI-X

Gb Ethernet

Cntrlr

ATI

VGA

PCI

32-bit/33 MHz

LPC Bus

Chapter 1: Introduction

1-5

1-3 Server Chassis Features

The SuperServer 5013C-MT is a 1U rackmount server platform configuration. The
following is a general outline of the main features of the SC813MT-300C chassis.

System Power

When configured as a SuperServer 5013C-MT, the SC813MT-300C chassis in­cludes a single 300W power supply.

Serial ATA Subsystem

The SC813MT-300C chassis was designed to support up to four Serial ATA hard
drives. The Serial ATA drives are hot-swappable units. ATA/100 IDE drives are
also supported.

Control Panel

The SC813MT-300C's control panel provides important system monitoring and
control information. LEDs indicate power on, network activity, hard disk drive
activity and overheat conditions. The control panel also includes a main power
button and a system reset button.

Rear I/O Panel

The rear I/O panel on the SC813MT-300C provides one motherboard expansion
slot, one COM port (another is internal), two USB ports, PS/2 mouse and key­board ports, a parallel (printer) port, a graphics port and two Gb Ethernet ports.
(See Figure 1-2.)

1-6

SUPERSERVER 5013C-MT User's Manual

Cooling System

The SC813MT-300C chassis has an innovative cooling design that features three
4-cm high performance cooling fans. The fans plug into headers on the
motherboard and operates at full rpm continuously.

Figure 1-2. Rear I/O Panel

Chapter 1: Introduction

1-7

1-4 Contacting Supermicro

Headquarters

Address: SuperMicro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)
Web Site: www.supermicro.com

Europe

Address: SuperMicro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Asia-Pacific

Address: SuperMicro, Taiwan

D5, 4F, No. 16 Chien-Ba Road

Chung-Ho 235, Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [e-mail]
Tel: [phone], ext.132 or 139

1-8

SUPERSERVER 5013C-MT User's Manual

Notes

Chapter 2: Server Installation

2-1

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your SuperServer 5013C-MT
up and running. Following the steps in the order given should enable you to have
the system operational within a minimal amount of time. This quick setup
assumes that your 5013C-MT system has come to you with the processor and
memory preinstalled. If your system is not already fully integrated with a moth­erboard, processor, system memory etc., please turn to the chapter or section
noted in each step for details on installing specific components.

2-2 Unpacking the SuperServer 5013C-MT

You should inspect the box the SuperServer 5013C-MT was shipped in and note
if it was damaged in any way. If the server itself shows damage, you should file
a damage claim with the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the SuperServer
5013C-MT. It should be situated in a clean, dust-free area that is well ventilated.
Avoid areas where heat, electrical noise and electromagnetic fields are gener­ated. You will also need it placed near a grounded power outlet. Read the Rack
and Server Precautions in the next section.

2-3 Preparing for Setup

The box the SuperServer 5013C-MT was shipped in should include two sets of rail
assemblies, six rail mounting brackets and the mounting screws you will need
to install the system into the rack. Follow the steps in the order given to
complete the installation process in a minimal amount of time. Please read this
section in its entirety before you begin the installation procedure outlined in the
sections that follow.

2-2

SUPERSERVER 5013C-MT User's Manual

Choosing a Setup Location

- Leave enough clearance in front of the rack to enable you to open

the front door completely (~25 inches).

- Leave approximately 30 inches of clearance in the back of the rack

to allow for sufficient airflow and ease in servicing.

Rack Precautions

- Ensure that the leveling jacks on the bottom of the rack are fully

extended to the floor with the full weight of the rack resting on them.

- In a single rack installation, stabilizers should be attached to the rack.

- In multiple rack installations, the racks should be coupled together.

- Always make sure the rack is stable before extending a component

from the rack.

- You should extend only one component at a time - extending two or

more simultaneously may cause the rack to become unstable.

Server Precautions

- Review the electrical and general safety precautions in Chapter 4.

- Determine the placement of each component in the rack before you

install the rails.

- Install the heaviest server components on the bottom of the rack

first, and then work up.

- Use a regulating uninterruptible power supply (UPS) to protect the server
from power surges, voltage spikes and to keep your system operating in
case of a power failure.

- Allow the power supply units and hot plug Serial ATA drive to cool before

touching them.

- Always keep the rack's front door and all panels and components on

the servers closed when not servicing to maintain proper cooling.

!

!

Warnings and Precautions!

Chapter 2: Server Installation

2-3

2-4 Installing the 5013C-MT into a Rack

This section provides information on installing the SuperServer 5013C-MT into a
rack unit. If the system has already been mounted into a rack, you can skip
ahead to Sections 2-5 and 2-6. There are a variety of rack units on the market,
which may mean the assembly procedure will differ slightly. The following is a
guideline for installing the unit into a rack with the rack rails provided with the
system. You should also refer to the installation instructions that came with the
rack unit you are using.

Identifying the Sections of the Rack Rails

You may have received rack rail hardware with the SuperServer 5013C-MT. (Two
front inner rails should already be attached to the chassis.) This hardware
consists of two rear inner rails that secure to the chassis, one on each side just
behind the preinstalled front inner rails. Note that these two rails are left/right
specific.

Installing the Rear Inner Rails

First, locate the right rear inner rail (the rail that will be used on the right side
of the chassis when you face the front of the chassis). Align the two square holes
on the rail against the hooks on the right side of the chassis. Securely attach
the rail to the chassis with M4 flat head screws. Repeat these steps to install
the left rear inner rail to the left side of the chassis (see Figure 2-1). You will

also need to attach the rail brackets when installing into a telco rack.

Locking Tabs: Both chassis rails have a locking tab, which serves two functions.
The first is to lock the server into place when installed and pushed fully into the
rack, which is its normal position. Secondly, these tabs also lock the server in
place when fully extended from the rack. This prevents the server from coming
completely out of the rack when you pull it out for servicing.

2-4

SUPERSERVER 5013C-MT User's Manual

Installing the Rack Rails

Determine where you want to place the SuperServer 5013C-MT in the rack (see
Rack and Server Precautions in Section 2-3). Position the chassis rail guides
at the desired location in the rack, keeping the sliding rail guide facing the inside
of the rack. Screw the assembly securely to the rack using the brackets pro­vided. Attach the other assembly to the other side of the rack, making sure that
both are at the exact same height and with the rail guides facing inward.

Figure 2-1. Installing Rear Inner Chassis Rails

Chapter 2: Server Installation

2-5

Figure 2-2. Installing the Server into a Rack

(with optional front bezel shown)

Installing the Server into the Rack

You should now have rails attached to both the chassis and the rack
unit. The next step is to install the server into the rack. Do this by
lining up the rear of the chassis rails with the front of the rack rails.
Slide the chassis rails into the rack rails, keeping the pressure even on
both sides (you may have to depress the locking tabs when inserting).
See Figure 2-2.

When the server has been pushed completely into the rack, you should
hear the locking tabs "click". Finish by inserting and tightening the
thumbscrews that hold the front of the server to the rack.

2-6

SUPERSERVER 5013C-MT User's Manual

Figure 2-3. Installing the Server into a Telco Rack

(with optional front bezel shown)

Installing the Server into a Telco Rack

If you are installing the SuperServer 5013C-MT into a Telco type rack, follow the
directions given on the previous pages for rack installation. The only difference
in the installation procedure will be the positioning of the rack brackets to the
rack. They should be spaced apart just enough to accomodate the width of the
telco rack.

Chapter 2: Server Installation

2-7

2-5 Checking the Motherboard Setup

After you install the 5013C-MT in the rack, you will need to open the unit to make
sure the motherboard is properly installed and all the connections have been
made.

1. Accessing the inside of the 5013C-MT (Figure 2-4)

First, release the retention screws that secure the unit to the rack. Grasp the
two handles on either side and pull the unit straight out until it locks (you will
hear a "click"). Next, depress the two buttons on the top of the chassis to
release the top cover while pushing the cover away from you until it stops.
You can then lift the top cover from the chassis to gain full access to the
inside of the server.

2. Check the CPU (processor)

You may have one processor already installed into the system board. The
processor should have its own heatsink attached. See Chapter 5 for instruc­tions on processor installation.

3. Check the system memory

Your 5013C-MT server system may have come with system memory already
installed. Make sure all DIMMs are fully seated in their slots. For details on
adding system memory, refer to Chapter 5.

4. Installing add-on cards

If desired, you can install an add-on card to the system. See Chapter 5
for details on installing a PCI add-on card.

5. Check all cable connections and airflow

Make sure all power and data cables are properly connected and not
blocking the airflow. See Chapter 5 for details on cable connections.
Also, check the air seals for damage. The air seals are located under
the blower fan and beneath the frame cross section that separates the
drive bay area from the motherboard area of the chassis.

Note: Make sure that the air seals are properly installed.

2-8

SUPERSERVER 5013C-MT User's Manual

Figure 2-4.

Accessing the Inside of the SuperServer 5013C-MT

Chapter 2: Server Installation

2-9

2-6 Checking the Drive Bay Setup

Next, you should check to make sure the peripheral drives and the Serial
ATA drive and Serial ATA backplane have been properly installed and all essen­tial connections have been made.

1. Accessing the drive bays

All drives can be accessed from the front of the server. For servicing
the CD-ROM and floppy drives, you will need to remove the top chassis
cover. The Serial ATA disk drive can be installed and removed from the front
of the chassis without removing the top chassis cover.

2. Installing a CD-ROM and floppy disk drives

Refer to Chapter 6 if you need to reinstall a CD-ROM and/or floppy disk
drive to the system.

3. Check the Serial ATA disk drive

Depending upon your system's configuration, your system may have one
Serial ATA drive already installed. If you need to install a Serial ATA drive,
please refer to the appropriate section in Chapter 6.

4. Check the airflow

Airflow is provided by three 4-cm high performance fans. The system compo­nent layout was carefully designed to promote sufficient airflow through the
small 1U rackmount space. Also note that all power and data cables have
been routed in such a way that they do not block the airflow generated by the
fan.

5. Supplying power to the system

The last thing you must do is to provide input power to the system. Plug
the power cord from the power supply unit into a high-quality power
strip that offers protection from electrical noise and power surges. It is
recommended that you use an uninterruptible power supply (UPS).

2-10

SUPERSERVER 5013C-MT User's Manual

Notes

Chapter 3: System Interface

3-1

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the control panel and one on the Serial ATA drive
carrier to keep you constantly informed of the overall status of the system as well
as the activity and health of specific components. There are also two buttons on
the chassis control panel. This chapter explains the meanings of all LED indi­cators and the appropriate response you may need to take.

3-2 Control Panel Buttons

There are two push-button buttons located on the front of the chassis.
These are (in order from left to right) a reset button and a power on/off
button.

! RESET: The reset switch reboots the system.

! POWER: This is the main power switch, which is used to apply or

turn off the main system power. Turning off system power with this button
removes the main power but keeps standby power supplied to the system.

RESET

3-2

SUPERSERVER 5013C-MT User's Manual

3-3 Control Panel LEDs

The control panel located on the front of the SC813MT-300C chassis has five
LEDs. These LEDs provide you with critical information related to different parts
of the system. This section explains what each LED indicates when illuminated
and any corrective action you may need to take.

! OVERHEAT: Indicates an overheat condition in the chassis. This may
be caused by cables obstructing the airflow in the system, or the ambient
room temperature being too warm. You should also check to make sure
that the chassis cover is installed and that all fans are present and operat­ing normally. Finally, check the air seals for damage. The air seals are
located under the blower fan and beneath the frame cross section that
separates the drive bay area from the motherboard area of the chassis.

! NIC2: Indicates network activity on GLAN2 when flashing .

! NIC1: Indicates network activity on GLAN1 when flashing.

! HDD: Channel activity for all HDDs. This light indicates CD-ROM and

SATA drive activity when flashing.

NIC2

NIC1