Supero SUPERSERVER 2027TR-D70RF+ User Manual

®

SUPER

SUPERSERVER

Revision 1.0

SUPERSERVER
2027TR-D70RF+

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at

www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and
documentation, is the property of Supermicro and/or its licensors, and is supplied only under a
license. Any use or reproduction of this product is not allowed, except as expressly permitted by
the terms of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTW ARE, OR DA TA ST ORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See

www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.

Manual Revision 1.0
Release Date: December 18, 2012

Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.

Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2012 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

iii

Preface

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the SuperServer 2027TR-D70RF+.
Installation and maintainance should be performed by experienced technicians only .

The SuperServer 2027TR-D70RF+ are all high-end servers based on the
SC217HD-R1K28MB 2U rackmount chassis and the dual processor X9DRT-HF+
serverboard.

Manual Organization

Chapter 1: Introduction

The fi rst chapter provides a checklist of the main components included with the
server system and describes the main features of the X9DRT-HF+ serverboard and
the SC217HD-R1K28MB chassis.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer
2027TR-D70RF+ into a rack and check out the server confi guration prior to
powering up the system. If your server was ordered without processor and memory
components, this chapter will refer you to the appropriate sections of the manual
for their installation.

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.

Chapter 4: System Safety

You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 2027TR-D70RF+.

Chapter 5: Advanced Serverboard Setup

Chapter 5 provides detailed information on the X9DRT-HF+ serverboard, including
the locations and functions of connections, headers and jumpers. Refer to
this chapter when adding or removing processors or main memory and when
reconfi guring the serverboard.

SUPERSERVER 2027TR-D70RF+ SUPERSERVER

iv

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the SC217HD-R1K28MB server
chassis. You should follow the procedures given in this chapter when installing,
removing or reconfi guring SATA or peripheral drives and when replacing system
power supply units and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed information
on running the CMOS Setup Utility.

Appendix A: BIOS Error Beep Codes
Appendix B: System Specifi cations

v

SUPERSERVER 2027TR-D70RF+ SUPERSERVER

Notes

vi

Table of Contents

Chapter 1 Introduction

1-1 Overview .........................................................................................................1-1

1-2 Serverboard Features .....................................................................................1-2

Processors ......................................................................................................1-2

Memory ...........................................................................................................1-2

SAS/SATA........................................................................................................ 1-2

PCI Expansion Slots .......................................................................................1-2

Onboard Controllers/Ports .............................................................................. 1-3

Graphics Controller .........................................................................................1-3

Other Features ................................................................................................ 1-3

1-3 Server Chassis Features ................................................................................ 1-3

System Power ................................................................................................. 1-3

SAS/SATA Subsystem .....................................................................................1-3

Front Control Panel ......................................................................................... 1-4

I/O Ports ..........................................................................................................1-4

Cooling System ............................................................................................... 1-4

Air Shrouds ..................................................................................................... 1-4

Mounting Rails ................................................................................................ 1-4

1-4 Advanced Power Management (for -F Models Only) .....................................1-4

Intel® Intelligent Power Node Manager (NM) .................................................1-4

Manageability Engine (ME) ............................................................................. 1-5

1-5 Contacting Supermicro ....................................................................................1-7

1-6 2U Twin: System Notes ...................................................................................1-8

Nodes ..............................................................................................................1-8

System Power ................................................................................................. 1-8

SAS/SATA Backplane/Drives .......................................................................... 1-8

Chapter 2 Server Installation

2-1 Overview .........................................................................................................2-1

2-2 Unpacking the System .................................................................................... 2-1

2-3 Preparing for Setup ......................................................................................... 2-1

Choosing a Setup Location .............................................................................2-2

2-4 Warnings and Precautions! ............................................................................. 2-2

Rack Precautions ............................................................................................ 2-2

Server Precautions ..........................................................................................2-2

Rack Mounting Considerations ....................................................................... 2-3

SUPERSERVER 2027TR-D70RF+ SUPERSERVER

vii

Ambient Operating Temperature ................................................................ 2-3

Reduced Airfl ow ......................................................................................... 2-3

Mechanical Loading ................................................................................... 2-3

Circuit Overloading ..................................................................................... 2-3

Reliable Ground ......................................................................................... 2-3

2-5 Installing the System into a Rack ...................................................................2-4

Separating the Sections of the Rack Rails ..................................................... 2-4

Locking Tabs ...................................................................................................2-5

Releasing the Inner Rail ................................................................................. 2-5

Installing The Inner Rails on the Chassis ....................................................... 2-6

Installing the Outer Rails on the Rack ............................................................ 2-7

Standard Chassis Installation ......................................................................... 2-8

Optional Quick Installation Method ................................................................. 2-9

2-6 Checking the Serverboard Setup ....................................................................2-9

Accessing the inside of the System ................................................................2-9

2-7 Checking the Drive Bay Setup .......................................................................2-11

Chapter 3 System Interface

3-1 Overview .........................................................................................................3-1

3-2 Control Panel Buttons ..................................................................................... 3-2

3-3 Control Panel LEDs ........................................................................................ 3-2

3-4 Drive Carrier LEDs .......................................................................................... 3-3

Chapter 4 Standardized Warning Statements for AC Systems

4-1 About Standardized Warning Statements ....................................................... 4-1

Warning Defi nition ...........................................................................................4-1

Installation Instructions ....................................................................................4-4

Circuit Breaker ................................................................................................ 4-5

Power Disconnection Warning ........................................................................ 4-6

Equipment Installation ..................................................................................... 4-8

Restricted Area ................................................................................................ 4-9

Battery Handling ............................................................................................4-10

Redundant Power Supplies .......................................................................... 4-12

Backplane Voltage ........................................................................................4-13

Comply with Local and National Electrical Codes ........................................ 4-14

Product Disposal ........................................................................................... 4-15

Hot Swap Fan Warning .................................................................................4-16

Power Cable and AC Adapter ......................................................................4-18

Table of Contents

viii

Chapter 5 Advanced Motherboard Setup

5-1 Handling the Motherboard .............................................................................. 5-1

Precautions .....................................................................................................5-1

Unpacking .......................................................................................................5-1

5-2 Rear I/O Ports ................................................................................................. 5-2

5-3 Processor and Heatsink Installation................................................................5-3

Installing a Passive CPU Heatsink .................................................................5-7

Removing the Passive Heatsink ..................................................................... 5-7

5-4 Installing Memory ............................................................................................5-8

Memory Support ..............................................................................................5-8

Maximum Memory ...........................................................................................5-8

DIMM Module Population Confi guration .................................................. 5-10

5-5 Adding PCI Expansion Cards .......................................................................5-12

5-6 Motherboard Details ...................................................................................... 5-13

5-7 Connector Defi nitions ....................................................................................5-16

5-8 Jumper Settings ............................................................................................ 5-19

Explanation of Jumpers ................................................................................ 5-19

5-9 Onboard Indicators ........................................................................................5-21

5-10 PCI-Express and Serial ATA Connections .................................................... 5-23

5-11 Installing Drivers ............................................................................................5-24

Supero Doctor III ........................................................................................... 5-25

5-12 Onboard Battery ............................................................................................5-27

Chapter 6 Advanced Chassis Setup

6-1 Static-Sensitive Devices ..................................................................................6-1

Precautions .....................................................................................................6-1

Unpacking .......................................................................................................6-1

6-2 Control Panel ..................................................................................................6-2

Accessing the inside of the System ................................................................6-3

6-4 Installing the Air Shrouds ................................................................................ 6-4

Air Shrouds ..................................................................................................... 6-4

6-5 Checking the Airfl ow ....................................................................................... 6-5

6-6 System Fans ................................................................................................... 6-5

Optional Fan Confi gurations ...........................................................................6-5

6-7 Removing and Installing the Backplane ..........................................................6-8

Removing the Backplane ................................................................................ 6-8

Installing the Backplane ................................................................................ 6-10

6-8 Installing the Motherboard .............................................................................6-11

I/O Shield .......................................................................................................6-11

SUPERSERVER 2027TR-D70RF+ SUPERSERVER

Compatible Motherboards ..............................................................................6-11

Permanent and Optional Standoffs ................................................................6-11

6-9 Node Installation/Removal ............................................................................6-13

6-10 Installing and Replacing the Adapter Card ................................................... 6-15

PCI Slot Setup .............................................................................................. 6-16

6-11 Installing and Removing Hard Drives ...........................................................6-18

6-12 Power Supply ................................................................................................ 6-22

Power Supply Replacement ..........................................................................6-22

Chapter 7 BIOS

7-1 Introduction ......................................................................................................7-1

Starting BIOS Setup Utility ..............................................................................7-1

How To Change the Confi guration Data ......................................................... 7-1

Starting the Setup Utility .................................................................................7-2

7-2 Main Setup ...................................................................................................... 7-2

7-3 Advanced Settings Menu ................................................................................ 7-3

7-4 Event Logs .................................................................................................... 7-26

7-5 IPMI ............................................................................................................... 7-28

7-6 Boot ...............................................................................................................7-30

7-7 Security .........................................................................................................7-31

7-8 Save & Exit ................................................................................................... 7-32

Appendix A BIOS Error Beep Codes
Appendix B System Specifi cations

ix

Table of Contents

x

Notes

SUPERSERVER 2027TR-D70RF+ SUPERSERVER

Chapter 1

Introduction

1-1 Overview

The SuperServer 2027TR-D70RF+ is a high-end server comprised of two main
subsystems: the SC217HD-R1K28MB 2U server chassis and the X9DRT-HF+ dual
processor serverboard in two hot-swap nodes. Please refer to our web site for
information on operating systems that have been certifi ed for use with the system
(www.supermicro.com).

In addition to the serverboard and chassis, various hardware components have
been included with the 2027TR-D70RF+ server, as listed below:

• Four (4) 2U Passive CPU heat sinks w/narrow ILM (SNK-P0048PS)

• Two (2) Plastic air shrouds (MCP-310-82718-0B)

• Four (4) 80x80x38mm cooling fans (FAN-0129L4)

• SATA/SAS Backplane

One (1) SAS Backplane for 12 2.5" HDD (BPN-SAS-217HD)
Twenty-four (24) hot-swap 2.5" HDD trays (MCP-220-00047-0B)
Two (2) SAS2 LSI2008 HD adapter cards (BPN-ADP-E16-L)

• One (1) Rails set (MCP-290-00053-0N)

Note: a complete list of safety warnings is provided on the Supermicro web site at

http://www.supermicro.com/about/policies/safety_information.cfm

Chapter 1: Introduction

1-1

1-2

SUPERSERVER 2027TR-D70RF+ USER'S MANUAL

1-2 Serverboard Features

At the heart of the 2027TR-D70RF+ server lies the
X9DRT-HF+, a dual processor serverboard based on the Intel®
C602 chipset and designed to provide maximum performance. Two of these
serverboards can be mounted in the SC217HD-R1K28MB chassis.

The sections below cover the main features of the X9DRT-HF+ serverboard (see
Figure 1-1 for a block diagram of the chipset).

Processors

The X9DRT-HF+ supports single or dual Intel Xeon® E5-2600 series processors
(Socket R LGA 2011). Please refer to the serverboard description pages on our
web site for a complete listing of supported processors (www.supermicro.com).

Memory

The X9DRT-HF+ has sixteen (16) DIMM slots supporting up to 512 GB of
DDR3-1600/1333/1066/800 MHz speed registered ECC SDRAM in up to
512 MB, 1 GB, 2 GB, 4 GB, 8 GB, 16 GB or 32 GB sizes at 1.35V or 1.5V
voltages. See Chapter 5 for details.

Note: Check the Supermicro website (www.supermicro.com) for the latest memory
support information.

SAS/SATA

An LSI® SAS2008 SAS2 controller is integrated into the installed BPN-ADP-E16-L
adapter cards to provide a twelve port 6 Gb/s SAS2 (Serial Attached SCSI) /SATA3
subsystem for each node. The system has either RAID 0, 1 and 10 support for the
SuperServer 2027TR-D70RF+ server. The SAS/SATA drives are hot-swappable
units.

Note: The operating system you use must have RAID support to enable the
hotswap c apabil ity an d RA ID fu nctio n of the SA S/SATA dri ves.

PCI Expansion Slots

The SuperServer 2027TR-D70RF+ has for each node one (1) available PCI-E 3.0
x8 Slot for SMC-Proprietary Micro LP Card (CPU1 Slot2) that can be used.

1-3

Chapter 1: Introduction

Onboard Controllers/Ports

The color-coded I/O ports include a VGA (monitor) port, two USB 2.0 ports (an
additional internal USB header and one Type A USB connector are included on the
serverboard), an IPMI 2.0 dedicated LAN port and two Ethernet ports.

Note: For IPMI Confi guration Instructions, please refer to the Embedded BMC
Confi guration User's Guide available @

http://www.supermicro.com/support/

manuals/ for IPMI 2.0 system.

Graphics Controller

The X9DRT-HF+ features an integrated Matrox® G200eW Video Controller.

Other Features

Other onboard features that promote system health include onboard voltage
monitors, a chassis intrusion header, auto-switching voltage regulators, chassis and
CPU overheat sensors, virus protection, node manager software and BIOS rescue.

1-3 Server Chassis Features

The following is a general outline of the main features of the SC217HD server
chassis.

System Power

Each SC217HD chassis model includes a high-effi ciency 80-plus Platinum certifi ed
power supply, rated at 1280 Watts plus one redundant backup power supply.
In the unlikely event your power supply fails, replacement is simple and can be
accomplished without tools.

SAS/SATA Subsystem

The SC217HD supports up to twenty-four (24) 2.5" hot-swap SAS/SATA drives in
trays (12 for each node). These drives are hot-swappable units and are connected
to a backplane that provides power and control.

Note: The operating system you use must have RAID support to enable the hot­swap capability of the drives.

1-4

SUPERSERVER 2027TR-D70RF+ USER'S MANUAL

Front Control Panel

SC217HD-R1K28MB chassis includes two front panels on the handles of the
chassis which control each of the systems. Each control panel on the SuperServer
2027TR-D70RF+ provides you with system monitoring and control for one server
node. LEDs indicate system power, HDD activity, network activity, system overheat
and power supply failure. A main power button and a system reset button are also
included.

I/O Ports

The SC217HD is an propriertary form factor chassis designed to be used in a 2U
rackmount confi guration. The SC217HD chassis provides a low-profi le add-on card
slot, a COM port, a VGA port, two USB 2.0 ports, one IPMI Ethernet port and two
Ethernet ports per node.

Cooling System

The SC217HD chassis accepts four system fans. System fans for the SC217HD
chassis are powered from the motherboards or the HDD backplane. On SC217HD
model chassis, the two fans on each side are controlled by two motherboards, so
that when one of the motherboard nodes is removed, the second motherboard will
continue to control both fans.

Air Shrouds

The SC217HD chassis includes two plastic air shrouds that direct the airfl ow where
cooling is needed on each serverboard. Always use the air shroud included with
your chassis on each serverboard.

Mounting Rails

The SC217HD includes a set of quick-release rails, and can be placed in a rack
for secure storage and use. To setup your rack, follow the step-by-step instructions
included in this manual.

1-4 Advanced Power Management (for -F Models Only)

Intel® Intelligent Power Node Manager (NM)

The Intel® Intelligent Power Node Manager (IPNM) provides your system with
real-time thermal control and power management for maximum energy effi ciency.
Although IPNM Specifi cation Version 1.5 is supported by the BMC (Baseboard

1-5

Chapter 1: Introduction

Management Controller), your system must also have IPNM-compatible
Manageability Engine (ME) fi rmware installed to use this feature.

Manageability Engine (ME)

The Manageability Engine, which is an ARC controller embedded in the IOH (I/O
Hub), provides Server Platform Services (SPS) to your system. The services
provided by SPS are different from those proveded by the ME on client platforms.

1-6

SUPERSERVER 2027TR-D70RF+ USER'S MANUAL

Figure 1-1. Intel C602 Chipset:

System Block Diagram

Note: This is a general block diagram and may not exactly repre-

sent the features on your motherboard. See the previous pages for

the actual specifi cations of your motherboard. This block diagram is

intended for your reference only.

#2

#2

#2

#2

#2

#2

#2

#2

PROCESSOR

SANDYBRIDGE

PROCESSOR

SANDYBRIDGE

QPI

DDR3 DIMM

DDR3 DIMM

DDR3 DIMM

DDR3 DIMM

#1

G

SSB

PATSBURG

PEG0

DMI

PEG1_1

PEG1_8

PCI-32bit

USB

LAN
I350
2 ports

AT25321

LPC

CPU FRONT

FAN Side

CPU REAR
(I/O Side)

USB

REAR

HDR 2X5

0,1

TPM Header

USB Type-A

2,3

U7C1

U6H1

H

F

E

Socket 0

Socket 1

#1

P0

P0

P1

P1

PE3 PE2 PE1 DMI

PE3 PE2 PE1 DMI

Gen3
x8

x4

VGA BMC

WPCM450

DDR2

PHY1

LAN

RTL8201F

SPI

SATA

Gen2

PCI-E x8 MicroLP SLOT

x4

RJ45 RJ45

Gen3

x8

Gen3

x8

PCI-E x8 in x4 SLOT

x8

x1

x8(0..7)

HOTSWAP INTERFACE

SATA2 #5

SATA2 #4

SATA2 #3

SATA2 #2

SATA3 #1

SATA3 #0

PORT6

PORT5

PORT4

PORT3

PORT2

PORT1

6/3/1.5

QPI

VGA CONN

DDR3 DIMM

DDR3 DIMM

#1

C

#1

D

DDR3 DIMM

DDR3 DIMM

A

B

#1

#1

#1

#1

J1

J2

1-7

Chapter 1: Introduction

1-5 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email:

[e-mail] (General Information)

[e-mail] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Asia-Pacifi c

Address: Super Micro Computer, Inc.

4F, No. 232-1, Liancheng Rd.

Chung-Ho Dist., New Taipei City 235

Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Web Site:

www.supermicro.com.tw

Technical Support:
Email:

[e-mail]

Tel: [phone]

1-8

SUPERSERVER 2027TR-D70RF+ USER'S MANUAL

1-6 2U Twin: System Notes

As a 2U Twin2 confi guration, the SuperServer 2027TR-D70RF+ is a unique server
system. With two system boards incorporated into a single chassis acting as two
separate nodes, there are several points you should keep in mind.

Nodes

Each of the two serverboards act as a separate node in the system. As independant
nodes, each may be powered off and on without affecting the others. In addition,
each node is a hot-swappable unit that may be removed from the rear of the chassis.
The nodes are connected to the server backplane by means of an adapter card.

Note: A guide pin is located between the upper and lower nodes on the inner chassis
wall. This guide pin also acts as a “stop” when a node is fully installed. If too much
force is used when inserting a node this pin may break off. Take care to slowly slide
a node in until you hear the “click” of the locking tab seating itself.

System Power

Dual 1280 Watt power supplies are used to provide the power for all four
serverboards. Each serverboard however, can be shut down independently of the
other with the power button on its own control panel.

SAS/SATA Backplane/Drives

As a system, the SuperServer 2027TR-D70RF+ supports the use of twenty-four (24)

2.5" SAS/SATA drives. A single SAS/SATA backplane works to apply system-based
control for power and fan speed functions, yet at the same time logically connects a
set of twelve SAS/SATA drives to each serverboard. See the Drive Bay Installation/
Removal section in Chapter 6 for the logical hard drive and node confi guration.

Chapter 2: Server Installation

2-1

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your SuperServer
2027TR-D70RF+ up and running. Following these steps in the order given should
enable you to have the system operational within a minimum amount of time.
This quick setup assumes that your system has come to you with the processors
and memory preinstalled. If your system is not already fully integrated with a
serverboard, processors, system memory etc., please turn to the chapter or section
noted in each step for details on installing specifi c components.

2-2 Unpacking the System

You should inspect the box the SuperServer 2027TR-D70RF+ was shipped in and
note if it was damaged in any way. If the server itself shows damage you should
fi le a damage claim with the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the SuperServer
2027TR-D70RF+. It should be situated in a clean, dust-free area that is well
ventilated. Avoid areas where heat, electrical noise and electromagnetic fi elds are
generated. You will also need it placed near a grounded power outlet. Read the
Rack and Server Precautions in the next section.

2-3 Preparing for Setup

The box the SuperServer 2027TR-D70RF+ was shipped in should include two
sets of rail assemblies, two rail mounting brackets and the mounting screws you
will need to install the system into the rack. Follow the steps in the order given to
complete the installation process in a minimum amount of time. Please read this
section in its entirety before you begin the installation procedure outlined in the
sections that follow.

2-2

SUPERSERVER 2027TR-D70RF+ USER'S MANUAL

Choosing a Setup Location

• Leave enough clearance in front of the rack to enable you to open the front door

completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for suffi cient airfl ow and ease in servicing.

• This product is for installation only in a Restricted Access Location (dedicated

equipment rooms, service closets and the like).

• This product is not suitable for use with visual display work place devices

acccording to §2 of the the German Ordinance for Work with Visual Display Units.

2-4 Warnings and Precautions!

Rack Precautions

• Ensure that the leveling jacks on the bottom of the rack are fully extended to

the fl oor with the full weight of the rack resting on them.

• In single rack installation, stabilizers should be attached to the rack. In multiple

rack installations, the racks should be coupled together.

• Always make sure the rack is stable before extending a component from the

rack.

• You should extend only one component at a time - extending two or more

simultaneously may cause the rack to become unstable.

Server Precautions

• Review the electrical and general safety precautions in Chapter 4.

• Determine the placement of each component in the rack before you install the

rails.

• Install the heaviest server components on the bottom of the rack fi rst, and then

work up.

• Use a regulating uninterruptible power supply (UPS) to protect the server from

power surges, voltage spikes and to keep your system operating in case of a
power failure.

• Allow any hot plug drives and power supply modules to cool before touching

them.

• Always keep the rack's front door and all panels and components on the servers

closed when not servicing to maintain proper cooling.

Chapter 2: Server Installation

2-3

Rack Mounting Considerations

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating
temperature of the rack environment may be greater than the ambient temperature
of the room. Therefore, consideration should be given to installing the equipment
in an environment compatible with the manufacturer’s maximum rated ambient
temperature (Tmra).

Reduced Airfl ow

Equipment should be mounted into a rack so that the amount of airfl ow required
for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.

Circuit Overloading

Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack
itself should be grounded. Particular attention should be given to power supply
connections other than the direct connections to the branch circuit (i.e. the use of
power strips, etc.).

Warning! To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system remains
stable. The following guidelines are provided to ensure your safety:

• This unit should be mounted at the bottom of the rack if it is the only unit in

the rack.

• When mounting this unit in a partially fi lled rack, load the rack from the bottom

to the top with the heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before

mounting or servicing the unit in the rack.

2-4

SUPERSERVER 2027TR-D70RF+ USER'S MANUAL

2-5 Installing the System into a Rack

This section provides information on installing the chassis into a rack unit with the
rails provided. There are a variety of rack units on the market, which may mean
that the assembly procedure will differ slightly from the instructions provided. You
should also refer to the installation instructions that came with the rack unit you
are using.

Note: This rail will fi t a rack between 26.5" and 36.4" deep.

Separating the Sections of the Rack Rails

The chassis package includes two rail assemblies in the rack mounting kit (Figure
2-1). Each assembly consists of two sections: an inner fi xed chassis rail that secures
directly to the server chassis and an outer fi xed rack rail that secures directly to
the rack itself.

Figure 2-1: Identifying the Outer Rail, Middle Rail and Inner Rails

(Left Rail Assembly Shown)

Inner Rail

Rail Assembly

(Shown with Rails

Retracted)

This Side Faces

Outward

Locking Tab

Middle Rail

Outer Rail

Chapter 2: Server Installation

2-5

Locking Tabs

Each inner rail has a locking tab. This tab locks the chassis into place when installed
and pushed fully into the rack. These tabs also lock the chassis in place when fully
extended from the rack. This prevents the server from coming completely out of
the rack when when the chassis is pulled out for servicing.

Releasing the Inner Rail

Releasing Inner Rail from the Outer Rails (Figure 2-2)

1. Identify the left and right outer rail assemblies as described on page 2-4.

2. Pull the inner rail out of the outer rail until it is fully extended as illustrated
below.

3. Press the locking tab down to release the inner rail.

4. Pull the inner rail all the way out.

5. Repeat steps 1-3 for the second outer rail.

Figure 2-2: Extending and Releasing the Inner Rail

1

2

1

1

1

3

1

4

2-6

SUPERSERVER 2027TR-D70RF+ USER'S MANUAL

Figure 2-4: Inner Rails Installed on the Chassis

Figure 2-3: Installing the Inner Rails

Installing The Inner Rails on the Chassis

Installing the Inner Rails (Figure 2-3 and Figure 2-4)

1. Confi rm that the left and right inner rails have been correctly identifi ed.

2. Place the inner rail fi rmly against the side of the chassis, aligning the hooks
on the side of the chassis with the holes in the inner rail.

3. Slide the inner rail forward toward the front of the chassis until the rail clicks
into the locked position, which secures the inner rail to the chassis.

4. Secure the inner rail to the chassis with the screws provided.

5. Repeat steps 1 through 4 above for the other inner rail.

1

3

1

4

1

4

1

2

Inner Rails

Chapter 2: Server Installation

2-7

Installing the Outer Rails on the Rack

Installing the Outer Rails (Figure 2-5)

1. Press upward on the locking tab at the rear end of the middle rail.

2. Push the middle rail back into the outer rail.

3. Hang the hooks of the front of the outer rail onto the slots on the front of
the rack. If necessary, use screws to secure the outer rails to the rack, as
illustrated above.

4. Pull out the rear of the outer rail, adjusting the length until it fi ts within the
posts of the rack.

5. Hang the hooks of the rear portion of the outer rail onto the slots on the rear
of the rack. If necessary, use screws to secure the rear of the outer rail to the
rear of the rack.

6. Repeat steps 1-5 for the remaining outer rail.

Figure 2-5: Extending and Releasing the Outer Rails

1

3

1

4

1

1

1

2

2-8

SUPERSERVER 2027TR-D70RF+ USER'S MANUAL

Note: The fi gure above is for illustration purposes only. Always install servers to
the bottom of the rack fi rst.

Standard Chassis Installation

Installing the Chassis into a Rack (Figure 2-6)

1. Confi rm that the inner rails are properly installed on the chassis.

2. Confi rm that the outer rails are correctly installed on the rack.

3. Pull the middle rail out from the front of the outer rail and make sure that the
ball-bearing shuttle is at the front locking position of the middle rail.

4. Align the chassis inner rails with the front of the middle rails.

5. Slide the inner rails on the chassis into the middle rails, keeping the pressure
even on both sides, until the locking tab of the inner rail clicks into the front of
the middle rail, locking the chassis into the fully extended position.

6. Depress the locking tabs of both sides at the same time and push the chassis
all the way into the rear of the rack.

7. If necessary for security purposes, use screws to secure the chassis handles
to the front of the rack.

Figure 2-6: Installing into a Rack

Ball-Bearing

Shuttle

Chapter 2: Server Installation

2-9

Optional Quick Installation Method

The following quick installation method may be used to install the chassis onto a
rack.

Installing the Chassis into a Rack

1. Install the whole rail assembly onto the rack as described on page 2-7.

2. Release the inner rail without retracting the middle rail.

3. Install the inner rails on the chassis as previously described on page 2-6.

4. Install the chassis onto the middle rail as described in the previous section.
Warning: do not pick up the server with the front handles. They are designed

to pull the system from a rack only.

Stability hazard. The rack stabilizing mechanism must be in place, or the
rack must be bolted to the fl oor before you slide the unit out for servicing.
Failure to stabilize the rack can cause the rack to tip over.

2-6 Checking the Serverboard Setup

After you install the SUPERSERVER 2027TR-D70RF+ in the rack, you will need
to open the unit to make sure the serverboard is properly installed and all the
connections have been made.

Accessing the inside of the System

Before operating the SC217 chassis for the fi rst time, it is important to remove the
protective fi lm over the cover of the chassis, in order to allow for proper ventilation
and cooling.

Removing the Chassis Cover and Protective Film (Figure 2-7)

1. Confi rm that the power cord has been removed from the rear of both power

supplies.

2. Peel off the protective fi lm covering the top cover and the top of the chassis

3. Remove the two screws which secure the top cover onto the chassis as

shown above.

4. Lift the top cover up and off the chassis.

5. Check that all ventilation openings on the top cover and the top of the chassis

are clear and unobstructed.

6. Replace the chassis cover and reconnect the AC power cord.

2-10

SUPERSERVER 2027TR-D70RF+ USER'S MANUAL

Caution: Except for short periods of time, do NOT operate the server without
the cover in place. The chassis cover must be in place to allow proper airfl ow
and prevent overheating.

Checking the Components and Setup

1. You may have one or two processors already installed into the serverboard.
Each processor needs its own heat sink. See Chapter 5 for instructions on
processor and heat sink installation.

2. Your SUPERSERVER 2027TR-D70RF+ server system may have come with
system memory already installed. Make sure all DIMMs are fully seated in
their slots. For details on adding system memory, refer to Chapter 5.

3. If desired, you can install add-on cards to the system. See Chapter 5 for
details on installing PCI add-on cards.

4. Make sure all power and data cables are properly connected and not blocking
the chassis airfl ow. Also make sure that no cables are positioned in front of
the fans. See Chapter 5 for details on cable connections.

Figure 2-7. Accessing the Inside of the System

Remove two

screws

Check Ventilation
Openings

1

2

1

5

1

3

1

4

Chapter 2: Server Installation

2-11

2-7 Checking the Drive Bay Setup

Next, you should check to make sure the peripheral drives and the SATA drives
have been properly installed and all connections have been made.

Checking the Drives

1. All drives are accessable from the front of the server. A hard drive can be
installed and removed from the front of the chassis without removing the top
chassis cover.

2. Depending upon your system's confi guration, your system may have one or
more drives already installed. If you need to install hard drives, please refer to
Chapter 6.

Checking the Airfl ow

1. Make sure there are no objects obstructing the airfl ow in and out of the
chassis. In addition, if you are using a front bezel, make sure the bezel's fi lter
is replaced periodically.

2. Except for brief periods while swapping hard drives, do not operate the server
without drives or the drive carriers in the drive bays. Use only recommended
server parts.

3. Make sure no wires or foreign objects obstruct airfl ow through the chassis.
Pull all excess cabling out of the airfl ow path or use shorter cables.

4. The control panel LEDs inform you of system status. See “Chapter 3: System
Interface” for details on the LEDs and the control panel buttons.

Providing Power

1. Plug the power cord(s) from the power supply unit(s) into a high-quality
power strip that offers protection from electrical noise and power surges. It is
recommended that you use an uninterruptible power supply (UPS).

2. Depress the power on button on the front of the chassis.

2-12

SUPERSERVER 2027TR-D70RF+ USER'S MANUAL

Notes