Supero SUPER S2DG2, SUPER S2DGR, SUPER S2DGE, SUPER S2DGU User's And Bios Manual

®

SUPER S2DG2
SUPER S2DGU
SUPER S2DGE

SUPER S2DGR

USER’S AND BIOS

MANUAL

Revision 1.4

SUPER

The information in this User’s Manual has been carefully reviewed and is believed to be
accurate. The vendor assumes no responsibility for any inaccuracies that may be contained
in this document, makes no commitment to update or to keep current the information in this
manual, or to notify any person or organization of the updates.

Please Note: For the
most up-to-date version of this manual, please see our web site at
www.supermicro.com.

SUPERMICRO COMPUTER reserves the right to make changes to the product described in
this manual at any time and without notice. This product, including software, if any, and
documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or
reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR
INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT HAVE
LIABILITY FOR ANY HARDWARE, SOFTWARE OR DATA STORED OR USED WITH THE
PRODUCT, INCLUDING THE COSTS OF THE REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE OR DATA.

Unless you request and receive written permission from SUPERMICRO COMPUTER, you may
not copy any part of this document.

Information in this document is subject to change without notice. Other products and
companies referred to herein are trademarks or registered trademarks of their respective
companies or mark holders.

Copyright © 1999 by SUPERMICRO COMPUTER INC.
All rights reserved.

Printed in the United States of America.

Preface

About This Manual

This manual is written for system houses, PC technicians and
knowledgeable PC end users. It provides information for the installation and
use of the SUPER S2DG2/S2DGU/S2DGE/S2DGR motherboard. The SUPER
S2DG2/S2DGU/S2DGE/S2DGR supports Pentium II and III Xeon processors.

The Pentium II/III Xeon processor with the Dual Independent Bus Architecture
is based on the "Slot 2" infrastructure, which will provide the headroom for
future high-performance processors.

Manual Organization

Chapter 1, Introduction, describes the features, specifications and perfor­mance of the SUPER S2DG2/S2DGU/S2DGE/S2DGR system board and pro­vides detailed information about the chipset.

Refer to Chapter 2, Installation, for instructions on how to install the Pentium
II/III Xeon processor, the retention mechanism and the heat sink support.
This chapter also provides you with instructions for handling static-sensitive
devices. Read this chapter when you want to install DIMM modules and to
mount the system board in the chassis. Also refer to this chapter to connect
the floppy and hard disk drives, IDE interfaces, parallel port and serial ports
as well as the cables for the power supply, reset cable, Keylock/Power LED,
speaker and keyboard.

If you encounter any problems, see Chapter 3, Troubleshooting, which de­scribes troubleshooting procedures for the video, the memory and the setup
configuration stored in memory. For quick reference, a general FAQ [Fre­quently Asked Questions] section is provided. Instructions are also included
for technical support procedures, returning merchandise for service and for
BIOS upgrades using our BBS#.

See Chapter 4 for configuration data and BIOS features.

iii

Preface

S2DG2/S2DGU/S2DGE/S2DGR User’s Manual

Chapter 5 has information on running setup and includes the default settings
for Standard Setup, Advanced Setup, Chipset Function, Power Management,
PCI/PnP Setup and Peripheral Setup.

Appendix A offers information on BIOS error beep codes and messages.

Appendix B shows post diagnostic error messages.

iv

Table of Contents

Table of Contents

Preface

About This Manual ...................................................................................................... ii i

Manual Organization ................................................................................................... ii i

Jumper Quick Reference ........................................................................................... viii

Front Control Panel Headers......................................................................................ix

Chapter 1: Introduction

1-1 Overview .......................................................................................................... 1 -1

SUPER S2DG2 Image ............................................................................. 1-2

SUPER S2DG2 Motherboard Layout ..................................................... 1- 3

SUPER S2DGU Image ............................................................................ 1-4

SUPER S2DGU Motherboard Layout ..................................................... 1-5

SUPER S2DGE Image ............................................................................ 1 -6

SUPER S2DGE Motherboard Layout ..................................................... 1- 7

SUPER S2DGR Image ............................................................................ 1-8

SUPER S2DGR Motherboard Layout ..................................................... 1-9

440GX AGP Chipset: System Block Diagram .................................... 1-10

Motherboard Features ........................................................................... 1-11

1-2 Chipset Overview .......................................................................................... 1-13

1-3 Slot 2 Architecture ........................................................................................ 1-13

1-4 PC Health Monitoring................................................................................... 1-13

1-5 ACPI/PC 98 Features .................................................................................. 1-16

1-6 Power Supply Requirements ....................................................................... 1-17

1-7 Super I/O ........................................................................................................ 1-18

1-8 AIC 7890 SCSI Controller ............................................................................ 1-19

1-9 AIC 7895 SCSI Controller ............................................................................ 1-19

1-10 AIC 7896 SCSI Controller ............................................................................ 1-20

Chapter 2: Installation

2-1 Static-Sensitive Devices ................................................................................ 2- 1

Precautions ............................................................................................... 2- 1

Unpacking ................................................................................................. 2 -1

2-2 Pentium II and III Xeon Processor Installation .......................................... 2- 1

Removing the Pentium II/III Xeon Processor ...................................... 2 -2

2-3 Explanation and Diagram of Jumper/Connector ........................................ 2 -4

2-4 Changing the CPU Speed ............................................................................. 2- 4

2-5 Mounting the Motherboard in the Chassis .................................................. 2- 5

v

S2DG2/S2DGU/S2DGE/S2DGR User’s Manual

2-6 Connecting Cables ......................................................................................... 2 -5

Power Supply Connectors ...................................................................... 2- 5

Secondary Power Connector .................................................................. 2- 5

Infrared Connector .................................................................................... 2- 5

PW_ON Connector .................................................................................... 2- 6

Reset Connector ...................................................................................... 2- 6

Hard Drive LED ........................................................................................ 2 -6

Keylock/Power LED Connector .............................................................. 2 -6

Speaker Connector .................................................................................. 2- 7

Power Save State Select ........................................................................ 2 -7

ATX PS/2 Keyboard and Mouse Ports ................................................. 2- 7

Universal Serial Bus ................................................................................ 2 -7

ATX Serial Ports ...................................................................................... 2- 8

CMOS Clear .............................................................................................. 2 -8

External Battery........................................................................................ 2- 8

Wake-On-LAN ........................................................................................... 2- 8

Fan Connectors........................................................................................ 2 -8

Chassis Intrusion ..................................................................................... 2 -9

SLED Indicator .......................................................................................... 2 -9

2-7 Installing DIMMs ............................................................................................. 2- 9

DIMM Installation ..................................................................................... 2 -9

2-8 Connecting the Parallel Port, FDD and HDD ........................................... 2-10

Parallel Port Connector ......................................................................... 2-11

Floppy Connector ................................................................................... 2-11

IDE Interfaces ......................................................................................... 2-11

SCSI Connectors .................................................................................... 2-12

Ultra2 LVD/SE SCSI Connector ............................................................ 2-13

AGP Port ................................................................................................. 2-14

Chapter 3: Troubleshooting

3-1 Troubleshooting Procedures ......................................................................... 3- 1

Before Power On ...................................................................................... 3 -1

Troubleshooting Flowchart ...................................................................... 3- 1

No Power ................................................................................................... 3 -2

No Video .................................................................................................... 3- 2

Memory Errors .......................................................................................... 3 -2

Losing the System’s Setup Configuration ............................................ 3-3

3-2 Technical Support Procedures ..................................................................... 3- 3

vi

Table of Contents

3-3 Frequently Asked Questions ......................................................................... 3- 4

3-4 Returning Merchandise for Service ............................................................. 3 -7

Chapter 4: AMIBIOS

4-1 Introduction....................................................................................................... 4 -1

4-2 BIOS Features ................................................................................................. 4 -2

BIOS Configuration Summary Screen ................................................... 4-3

AMIBIOS Setup ......................................................................................... 4 -3

Chapter 5: Running Setup

5-1 Setup ................................................................................................................. 5-1

5-1-1 Standard CMOS Setup .................................................................. 5- 1

5-1-2 Advanced CMOS Setup ................................................................. 5-3

5-1-3 Advanced Chipset Setup ............................................................... 5- 7

5-1-4 Power Management Setup .......................................................... 5-13

5-1-5 PCI/PnP Setup .............................................................................. 5-15

5-1-6 Peripheral Setup ........................................................................... 5-17

5-2 Auto Detect Hard Disks................................................................................ 5-19

5-3 Change User/Supervisor Password ............................................................ 5-20

5-4 Change Language Setting ............................................................................ 5-20

5-5 Default Settings ............................................................................................. 5-21

5-4-1 Auto Configuration with Optimal Settings................................. 5-21

5-4-2 Auto Configuration with Fail-Safe Settings ............................... 5-21

Appendices:

Appendix A: BIOS Error Beep Codes and Messages ......................................... A- 1

Appendix B: AMIBIOS Post Diagnostic Error Messages .................................... B -1

vii

S2DG2/S2DGU/S2DGE/S2DGR User’s Manual

viii

S2DG2/S2DGR S2DGU/S2DGE*

Jumpers

JB1, JB2, JB3, JB4
JBT1
JP20
BZ_ON
JA5, JA6, JA7

**

JOH
J36

Connectors

J17
J18
J19
J20
J21
J32
J34
JA1, JA2 (S2DG2)
JA1, JA2 (S2DGR)
JA3
JBT2
JF1

JF2

JL1
SLED
JT1/JT1A
JT2/JT2A
JT3/JT3A
WOL

Function Page

CPU Core/Bus Ratio Selection 2-4
CMOS Clear 2-8
Power Save State 2-7
Overheat Alarm Enable 1-5
SCSI Termination
(default on = terminated) 1-3,9
Overheat LED Header 1-3,9
Secondary Power Connector 2-5

Function Page

USB 2-7
USB 2-7
Parallel Port 2-11
COM 1 2-8
COM 2 2-8
ATX Power Connector 2-5
PS/2 KB and Mouse 2-7
Ultra2 LVD/SE SCSI 2-13
UW SCSI 2-12
SCSI 2-12
External Battery 2-8
IDE Hard Drive LED 2-6
Keylock 2-6
Speaker 2-7
IR Connector 2-5
PW_ON 2-6
Reset 2-6
Chassis Intrusion 2-9
SCSI LED 2-9
CPU 1 Fan 2-8
CPU 2 Fan 2-8
Thermal Control Fan 2-8
Wake-On-LAN 2-8

Jumpers

JB1, JB2, JB3, JB4
JBT1
JP20
S-TERM

JOH
BZ_ON
J36

Connectors

J17
J18
J19
J20
J21
J32
J34
JA1
JA2
JA4
JBT2
JF1

JF2

JL1
SLED
JT1/JT1A
JT2/JT2A
JT3/JT3A
WOL

Function

CPU Core/Bus Ratio Selection
CMOS Clear
Power Save State
SCSI Termination
(default on = terminated)
Overheat LED Header
Overheat Alarm Enable
Secondary Power Connector

Function

USB
USB
Parallel Port
COM 1
COM 2
ATX Power Connector
PS/2 KB and Mouse
Ultra2 LVD/SE SCSI
UW SCSI
SCSI
External Battery
IDE Hard Drive LED
Keylock
Speaker
IR Connector
PW_ON
Reset
Chassis Intrusion
SCSI LED
CPU 1 Fan
CPU 2 Fan
Thermal Control Fan
Wake-On-LAN

* SCSI jumpers and connectors do not apply to the S2DGE.
** S2DG2: Jumping JA5 terminates SCSI connector JA1.

Jumping JA6 terminates SCSI connector JA3.
Jumping JA7 terminates SCSI connector JA2.

S2DGR: Jumping JA5 terminates SCSI connectors JA1 and JA3.

Jumping JA6 terminates SCSI connector JA2.
(JA7 is not used for the S2DGR.)

Jumper Quick Reference

ix

Front Control Panel

Front Control Panel Headers

See pages 2-5 through 2-7 for
pin definitions.

Keyboard
lock

Speaker

IR Con

Power On

X

Reset

JF2 JF1

X

Power
LED

11

Hard
Drive LED

x

Notes

Preface

Chapter 1: Introduction

1-1

Chapter 1

Introduction

1-1 Overview

The SUPER S2DG2/S2DGU/S2DGE/S2DGR supports dual Pentium II Xeon
and dual Pentium III Xeon processors. All four motherboards are based on Intel’s
440GX chip set, which supports a 100 MHz system bus speed, an Accelerated
Graphics Port (AGP), Wake-on-LAN, SDRAM, concurrent PCI and a 33 MB/s
Ultra DMA burst data transfer rate.

While all of the motherboards are the ATX form factor, the S2DG2, S2DGU and
S2DGE have 5 PCI and 2 ISA slots (with one shared). The S2DGR has 4 PCI
and 2 ISA slots (with one shared). All have an AGP port and can accommodate
up to 2 GB unbuffered SDRAM or registered SDRAM memory in 4 168-pin DIMM
sockets.

AGP reduces contention between the CPU and I/O devices by broadening the
graphics bandwidth to memory. It delivers a maximum of 532 MB/s in the 2x
transfer mode, which is quadruple the PCI speed!

Wake-On-LAN allows for the remote network management and configuration of
the PC, even in off-hours when the PC is turned off. This reduces the complexity
of managing the network.

Other features that maximize customer satisfaction and simplicity in managing
the computer are its support for the PC 98-ready and and the Advanced Configu­ration and Power Interface (ACPI) standards. With PC Health Monitoring, you
can protect your system from problems before they even occur.

All motherboards include the following I/O: 2 EIDE ports, a floppy port, an ECP/
EPP supported parallel port, PS/2 mouse and PS/2 keyboard ports, 2 serial
ports, an infrared port and 2 USB ports. The S2DGR has an integrated onboard
Adaptec 7895 dual UW SCSI controller. The dual channels enable a data transfer
rate of 40 MB/s per channel and an optional RAID II port (ARO-1130CA/SA). The
S2DG2 has the onboard Adaptec 7896 controller for Ultra2 LVD (Low Voltage
Device) SCSI, which enables a data transfer rate of 80 MB/s per channel and an
optional RAID III port (ARO-1130C). In addition, this motherboard has an onboard
RAID port to support the Adaptec ARO-1130C RAIDport III card for increased I/
O performance and fault tolerance. The S2DGU provides an onboard Adaptec
7890 Ultra2 LVD SCSI controller, which enables data transfer rates of up to 80
MB/s, and an optional RAID III port (ARO-1130C).

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

1-2

SUPER S2DG2

Figure 1-1. SUPER S2DG2 Motherboard Image

Chapter 1: Introduction

1-3

Figure 1-2. SUPER S2DG2 Motherboard Layout

12"

J21

COM2

J20

COM1

J14

J13

J34

PS/2 KB

PS/2

MOUSE

J9

J11

J12

J10

PW_ON

RESET

JF1

IDE LED/KEYLOCK/SPEAKER

IR CON

JF2

U38

U14

J8

J17, J18

USB

U2

SCSI

JA1

BIOS

BT2

B

A

T

T

E

R

Y

+

-

UA12

JA4

RAID PORT

U48

JL1

A

G

P

P

O

R

T

U37

U15

JP11

Ultra2 LVD/SE

Channel A

PIIX4

GX

J19

Parallel

Port

J35

1

JL2

1

JTM

JB4

JB3

JB2

J

B

1

1

WOL

J15

1

FLO

PPY

J22

JBT1

JBT2

12"

10.65"

10.65"

1

JA2

BZ

PCI 4

PCI 5

PCI 3

PCI 2

PCI 1

SBLINK

U58

U18

U19

1

JP20

B

a

nk

0

Bank1

Bank2

Bank3

JT2

JT1

1

J1

J2

ATX POWER (A)

JT2A

JT1A

1

1

1

1

J32A

1

JA3

1

JT3A

JT3

1

IDE 2

ID

E

1

J16

OSC1

JPR1

PWR_SEC

J7

J5

J4

J6

1

1

1

JOH

Overheat

LED

Chassis

Intrusion

SLED

1

BZ_ON

J36

®

1

——–—— Manufacturer Settings —–———
JBT1: 1-2 (default)

2-3 CMOS Clear
*To clear CMOS completely,
disconnect the power source.

JL1: OFF (default)

ON (intrusion)

JP 1 1 : 1-2 = 100 MHz

2-3 = 66 MHz

JP2 0 : 1-2 PIIX CTL PD State

2-3 BIOS CTL PD State (default)
WOL: Wake-On-LAN
JA5: SCSI Termination for JA1
JA6: SCSI Termination for JA3
JA7: SCSI Termination for JA2
——–———————–——–—–——–——–—

Note: JA3 is optional.

Note: To enable the overheat buzzer, place a jumper

on BZ_ON.

ATX POWER (B)

J32B

1

1

1

1

1

JA5

JA7

JA6

1

1

1

SUPER S2DG2

Ultra2 LVD/SE

Channel B

————— CPU Core/Bus Ratio –—————

JB1 JB2 JB3 JB4
x 3 ON OFF ON ON
x3.5 OFF OFF ON ON
x 4 ON ON OFF ON
x4.5 OFF ON OFF ON
x5 ON OFF OFF ON
x5.5 OFF OFF OFF ON
x 6 ON ON ON OFF
x6.5 OFF ON ON OFF
x7 ON OFF ON OFF
x7.5 OFF OFF ON OFF
——–—–————————————————

Note: Some CPU Core/Bus ratios cannot be selected

with jumpers for processors that have fixed ratios.

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

1-4

SUPER S2DGU

Figure 1-3. SUPER S2DGU Motherboard Image

Chapter 1: Introduction

1-5

8.7"

SUPER S2DGU

Figure 1-4. SUPER S2DGU Motherboard Layout

J21

COM2

J20

COM1

J14

J13

J34

PS/2 KB

PS/2

MOUSE

J9

J11

J12

J10

PW_ON RESET

JF1

IDE LED/KEYLOCK/SPEAKER

IR CON

JF2

U38

U14

J8

J17, J18

USB

U2

SCSI

JA1

BIOS

BT2

B

A

T

T

E

R

Y

+

-

UA12

JA3

RAID PORT

U48

JL1

A

G

P

P

O

R

T

U37

U15

JP11

UW SCSI

Ultra2 LVD/SE

——–—— Manufacturer Settings —–———
JBT1: 1-2 (default)

2-3 CMOS Clear
*To clear CMOS completely,
disconnect the power source.

JL1: OFF (default)

ON (intrusion)

JP 1 1 : 1-2 = 100 MHz

2-3 = 66 MHz

JP2 0 : 1-2 PIIX CTL PD State

2-3 BIOS CTL PD State (default)
WOL: Wake-On-LAN
S-TERM: On: SCSI Termination Enable

Off: Termination Disable
——–———————–——–—–——–——–—

PIIX4

GX

J19

Parallel

Port

J35

1 JL2

1

JTM

JB4

JB3

JB2

J

B

1

1

WOL

J15

1

FLO

P

PY

J22

JBT1

JBT2

S

-TE

R

M

12"

10.65"

9.65"

1

JA2

BZ

PCI 4

PCI 5

PCI 3

PCI 2

PCI 1

SBLINK

U58

U18

U19

1

JP20

B

a

n

k

0

Bank1

Bank2

B

ank3

JT2

JT1

1

J1

J2

ATX POWER

JT2A

JT1A

1

1

1

1

J32

1

JA4

1

JT3A

JT3

1

IDE 2

IDE

1

J16

OSC1

JPR1

PWR_SEC

J7

J5

J4

J6

1

1

1

JOH

Overheat

LED

Chassis

Intrusion

SLED

1

BZ_ON

J36

Note: To enable the overheat buzzer, place a jumper

on BZ_ON.

Note: JA3 is optional.

®

1

————— CPU Core/Bus Ratio –—————

JB1 JB2 JB3 JB4
x 3 ON OFF ON ON
x3.5 OFF OFF ON ON
x 4 ON ON OFF ON
x4.5 OFF ON OFF ON
x5 ON OFF OFF ON
x5.5 OFF OFF OFF ON
x 6 ON ON ON OFF
x6.5 OFF ON ON OFF
x7 ON OFF ON OFF
x7.5 OFF OFF ON OFF
——–—–————————————————

Note: Some CPU Core/Bus ratios cannot be selected

with jumpers for processors that have fixed ratios.

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

1-6

SUPER S2DGE

Figure 1-5. SUPER S2DGE Motherboard Image

Chapter 1: Introduction

1-7

Figure 1-6. SUPER S2DGE Motherboard Layout

8.7"

J21

COM2

J20

COM1

J14

J13

J34

PS/2 KB

PS/2

MOUSE

J9

J11

J12

J10

PW_ON

RESET

JF1

IDE LED/KEYLOCK/SPEAKER

IR CON

JF2

U38

U14

J8

J17, J18

USB

U2

BIOS

BT2

B

A

T

T

E

R

Y

+

-

UA12

JA3

RAID PORT

U48

JL1

A

G

P

P

O

R

T

U37

U15

JP11

PIIX4

GX

J19

Parallel

Port

J35

1

JL2

1

JTM

JB4

JB3

JB2

J

B

1

1

WOL

J15

FLO

PPY

J22

JBT1

JB

T2

10.65"

9.65"

BZ

PCI 4

PCI 5

PCI 3

PCI 2

PCI 1

SBLINK

U58

U18

U19

1

JP20

B

an

k0

Bank1

Bank2

Bank3

JT2

JT1

1

J1

J2

ATX POWER

JT2A

JT1A

1

1

1

1

J32

1

JT3A

JT3

1

IDE 2

ID

E

1

J16

OSC1

JPR1

PWR_SEC

J7

J5

J4

J6

1

1

1

JOH

Overheat

LED

Chassis

Intrusion

1

BZ_ON

J36

®

1

SUPER S2DGE

——–—— Manufacturer Settings —–———
JBT1: 1-2 (default)

2-3 CMOS Clear
*To clear CMOS completely,
disconnect the power source.

JL1: OFF (default)

ON (intrusion)

JP 11: ON = 66 MHz

OFF = 100 MHZ

JP2 0 : 1-2 PIIX CTL PD State

2-3 BIOS CTL PD State (default)
WOL: Wake-On-LAN
——–———————–——–—–——–——–—

Note: To enable the overheat buzzer, place a jumper

on BZ_ON.

12"

1

————— CPU Core/Bus Ratio –—————

JB1 JB2 JB3 JB4
x 3 ON OFF ON ON
x3.5 OFF OFF ON ON
x 4 ON ON OFF ON
x4.5 OFF ON OFF ON
x5 ON OFF OFF ON
x5.5 OFF OFF OFF ON
x 6 ON ON ON OFF
x6.5 OFF ON ON OFF
x7 ON OFF ON OFF
x7.5 OFF OFF ON OFF
——–—–————————————————

Note: Some CPU Core/Bus ratios cannot be selected

with jumpers for processors that have fixed ratios.

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

1-8

SUPER S2DGR

Figure 1-7. SUPER S2DGR Motherboard Image

Chapter 1: Introduction

1-9

®

J21

COM2

J20

COM1

J34

PS/2 KB

PS/2

MOUSE

J9

J11

J12

J10

PW_ON

RESET

JF1

IDE LED/KEYLOCK/SPEAKER

IR CON

JF2

U38

U14

J8

J17, J18

USB

U2

SCSI

BIOS

WOL

UA1

JA4

PCI 1

PCI 2

PCI 3

PCI 4

U48

A

G

P

P

O

R

T

U37

U15

UW SCSI

JTM

PIIX4

GX

J19

Parallel

Port

Figure 1-8. SUPER S2DGR Motherboard Layout

Note: To enable the overheat buzzer, place a jumper

on BZ_ON.

12"

9.6"

10.125"

UW SCSI

J13

J14

SBLINK

1

RAID PORT

SUPER S2DGR

JL2

JL1

1

B

a

n

k

0

Bank1

Bank2

B

ank3

JB2

JB3

JB

4

JB1

JT2

JT2

JT1A

1

1

JP12

1

1

JP13

J3

J1

J2

JA7

JA5

JP20

1

BT2

-

+

1

SCSI LED

JBT2

JBT1

1

B

A

T

T

E

R

Y

J5

J6

J7

J4

1

11

J22

6.0"

ATX POWER

JA3

1

JA1

JA2

1

J15

J16

FL

O

P

P

Y

JP11

Chassis

Intrusion

BZ_ON

1

1

JT2A

JT1

JT3

JTA3

1

1

1

PWR_SEC

J36

J32

1

1

1

JOH1

——–—— Manufacturer Settings —–———
JBT1: 1-2 (default)

2-3 CMOS Clear
*To clear CMOS completely,
disconnect the power source.

JL1: OFF (default)

ON (intrusion)

JP11: ON = 66 MHz

OFF = 100 MHZ

JP2 0 : 1-2 PIIX CTL PD State

2-3 BIOS CTL PD State (default)
WOL: Wake-On-LAN
JA5: SCSI Termination for JA1 and JA3
JA6: SCSI Termination for JA2
——–———————–——–—–——–——–—

1

IDE2

IDE1

Note: Some CPU Core/Bus ratios cannot be selected

with jumpers for processors that have fixed ratios.

————— CPU Core/Bus Ratio –—————

JB1 JB2 JB3 JB4
x 3 ON OFF ON ON
x3.5 OFF OFF ON ON
x 4 ON ON OFF ON
x4.5 OFF ON OFF ON
x5 ON OFF OFF ON
x5.5 OFF OFF OFF ON
x 6 ON ON ON OFF
x6.5 OFF ON ON OFF
x7 ON OFF ON OFF
x7.5 OFF OFF ON OFF
——–—–————————————————

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

1-10

CPU

440GX

CPU

AGP

Port

IO

APIC

PIIX4

Power

Management

SDRAM

Host Bus

PCI Slots

SMBus

USB

Ports

USB

IDE Ports

ISA Slots

BIOS

SIO

SCSI

Figure 1-9. 440GX AGP Chipset:

System Block Diagram (Dual Processors)

NOTE: This is a general block diagram and may not

represent the number of slots/CPUs on your motherboard.

See the following page for the actual specifications of each

motherboard.

Chapter 1: Introduction

1-11

Features of the S2DG2, S2DGU, S2DGE and S2DGR
Motherboards

The following list covers the general features of the S2DG2, S2DGU, S2DGE and
S2DGR motherboards.

CPU (Note: These boards may run with a single CPU in either slot.)

• Dual Pentium II Xeon and dual Pentium III Xeon processors at 100 MHz
bus speed

Memory

• 2 GB unbuffered 3.3V SDRAM or 2 GB registered SDRAM

(Note: The SDRAM must be PC-100 compliant DIMMs.)
(Note: The maximum cacheable memory size depends on processor capability.)

• Error Checking and Correction and Error Checking support

Chipset

• Intel 440GX

Expansion Slots

S2DGR S2DG2, S2DGU, S2DGE

• 4 PCI slots • 5 PCI slots

• 2 ISA slots • 2 ISA slots
[one PCI/ISA shared slot] [one PCI/ISA shared slot]

• 1 AGP slot • 1 AGP slot

BIOS

• 2 Mb AMI® Flash BIOS

• APM 1.2, DMI 2.1, Plug and Play (PnP)

• Adaptec 7890 SCSI BIOS (S2DGU)

• Adaptec 7895 SCSI BIOS (S2DGR)

• Adaptec 7896 SCSI BIOS (S2DG2)

PC Health Monitoring

• Seven onboard voltage monitors for CPU core(s), CPU I/O, +3.3V, ±5V,
and ±12V

• Three-fan status monitor with firmware/software on/off control

• Environmental temperature monitor and control

• CPU fan auto-off in sleep mode

• Chassis overheat alarm, LED and control

• Chassis intrusion detection

• System resource alert

• Hardware BIOS virus protection

• Auto-switching voltage regulator for the CPU core

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

1-12

• SUPERMICRO SUPER Doctor and Intel® LANDesk® Client Manager
(LDCM) support

ACPI/PC 98 Features

• Microsoft OnNow

• Slow blinking LED for suspend state indicator

• BIOS support for USB keyboard

• Real-time clock wake-up alarm

• Main switch override mechanism

• External modem ring-on

Onboard I/O

• Two 68-pin 16-bit Ultra2 LVD/SE SCSI connectors and one 50-pin 8-bit
SCSI connector (S2DG2)

• One 68-pin 16-bit Ultra2 LVD/SE SCSI connector, one 68-pin 16-bit Ultra
Wide SCSI connector and one 50-pin 8-bit SCSI connector (S2DGU)

• Two 68-pin 16-bit Ultra Wide SCSI connectors and one 50-pin 8-bit SCSI
connector (S2DGR)

• RAID port for Adaptec ARO-1130CA/SA RAIDport II card (S2DGR)

• RAID port for Adaptec ARO-1130C RAIDport III card (S2DG2, S2DGU)

• 2 EIDE Bus Master interfaces support Ultra DMA/33 and Mode 4

• 1 floppy port interface

• 2 Fast UART 16550 serial ports

• 1 parallel port that supports EPP (Enhanced Parallel Port) and ECP
(Extended Capabilities Port)

• PS/2 mouse and PS/2 keyboard

• Infrared port

• 2 USB (Universal Serial Bus) ports

CD Utilities

• Intel LANDesk Client Manager for Windows NT® and Windows® 95
(optional)

• PIIX4 Upgrade Utility for Windows 95

• BIOS Flash Upgrade Utility

• SUPER Doctor Utility

• SCSI Utility, manual and driver

Dimensions

• SUPER S2DG2 - ATX (12" x 10.65") *See board diagram for full measurements.

• SUPER S2DGU - ATX (12" x 9.65") *See board diagram for full measurements.

• SUPER S2DGE - ATX (12" x 9.65") *See board diagram for full measurements.

• SUPER S2DGR - ATX (12" x 9.6") *See board diagram for full measurements.

Chapter 1: Introduction

1-13

1-2 Chipset Overview

The 440GX chipset, developed by Intel, is the ultimate processor platform tar­geted for 3D graphics and multimedia applications. Along with a System-to-PCI
bridge integrated with an optimized DRAM controller and data path, this chipset
supports the Accelerated Graphics Port (AGP) interface. AGP is a high perfor­mance, component level interconnect targeted at 3D applications and based on
a set of performance enhancements to PCI. The I/O subsystem portion of the
440GX platform is based on the PIIX4, a highly integrated version of Intel's PCI­to-ISA bridge family.

The PCI/AGP and system bus interface controller (82443GX) supports up to two
Pentium II/III processors. It provides an optimized 72-bit DRAM interface (64-bit
data plus ECC). This interface supports 3.3V DRAM technologies. The control­ler provides the interface to a PCI bus operating at 33 MHz. This interface
implementation is compliant with the PCI Rev 2.1 Specification. The AGP inter­face is based on AGP Specification Rev 1.0. It can support data transfer rates
of up to 133 MHz (532 MB/s) .

1-3 Slot 2 Architecture

The Slot 2 architecture supports Intel Pentium II and III Xeon CPUs. This tech­nology offers a larger L2 cache that can run at full CPU speed.

1-4 PC Health Monitoring

This section describes the PC health monitoring features of the SUPER S2DG2/
S2DGU/S2DGE/S2DGR. All have an onboard System Hardware Monitor chip
that supports PC health monitoring.

Seven Onboard Voltage Monitors for the CPU Core(s), CPU I/
O, +3.3V,

±±

±±

±5V,

and

±±

±±

±12V

The onboard voltage monitor will scan these seven monitored voltages continu­ously. Once a voltage becomes unstable, a warning is given or an error message
is sent to the screen. Users can adjust the voltage thresholds to define the
sensitivity of the voltage monitor.

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

1-14

Three-Fan Status Monitor with Firmware/Software On/Off
Control

The PC health monitor can check the RPM status of the cooling fans. The
thermal fans are controlled by the overheat detection logic.

Please Note: The

tachometer readings are for JT1, JT2 and JT3 only

.

Environmental Temperature Control

A thermal control sensor monitors the CPU temperature in real-time and will turn
on a back-up fan whenever the CPU temperature exceeds a user-defined thresh­old. The overheat circuitry runs independently from the CPU. It can continue to
monitor for overheat conditions even when the CPU is in sleep mode. Once it
detects that the CPU temperature is too high, it will automatically turn on the
back-up fan to prevent any overheat damage to the CPU. The onboard chassis
thermal circuitry can monitor the overall system temperature and alert users
when the chassis temperature is too high.

CPU Fan Auto-Off in Sleep Mode

The CPU fan is activated when the power is turned on. It can be turned off when
the CPU is in sleep mode. When in sleep mode, the CPU will not run at full
power, thereby generating less heat. For power saving purposes, the user has
the option to shut down the CPU fan.

System Overheat Alarm, LED and Control

This feature is available when the user enables the system overheat warning
function in BIOS (see page 5-18). The overheat alarm will activate when the
system temperature exceeds the temperature threshold configured by the user.
When the overheat alarm is activated, both the overheat fan and the warning LED
are triggered.

Note: The alarm, fan and LED will remain on until the com-

puter is restarted.

Chassis Intrusion Detection

The chassis intrusion circuitry can detect unauthorized intrusion to the system.
The chassis intrusion connector is located on JL1. Attach a microswitch to JL1.
When the microswitch is closed, it means that the chassis has been opened.
The circuitry will then alert the user with a warning message when the system
is turned on. This feature is available when the user is running Intel's LANDesk
Client Manager and SUPERMICRO's Super Doctor.

Chapter 1: Introduction

1-15

System Resource Alert

This feature is available when used with Intel's LANDesk Client Manager. It is
used to notify the user of certain system events. For example, if the system is
running low on virtual memory and there is insufficient hard drive space for saving
the data, you can be alerted of the potential problem.

Hardware BIOS Virus Protection

The system BIOS is protected by hardware so that no virus can infect the BIOS
area. The user can only change the BIOS contents through the flash utility
provided by SUPERMICRO. This feature can prevent viruses from infecting the
BIOS area and destroying valuable data.

Auto-Switching Voltage Regulator for the CPU Core

The auto-switching voltage regulator for the CPU core can support up to 20A
current, with the auto-sensing voltage ID ranging from 1.3 to 3.5 volts. This will
allow the regulator to run cooler and thus make the system more stable.

Intel LANDesk® Client Manager (LDCM) Support

As the computer industry grows, PC systems have become more complex and
harder to manage. Historically, only experts have been able to fully understand
and control these complex systems. Today's users want manageable systems
that they can interact with automatically. Client Manager enables both admin­istrators and clients to:

• Review system inventory

• View DMI-compliant component information

• Back-up and restore system configuration files

• Troubleshoot

• Receive notifications for system events

• Transfer files to and from client workstations

• Remotely boot up client workstations

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

1-16

1-5 ACPI/PC 98 Features

ACPI stands for Advanced Configuration and Power Interface. The ACPI speci­fication defines a flexible and abstract hardware interface that provides a stan­dard way to integrate power management features throughout a PC system,
including hardware, the operating system and application software. This enables
the system to automatically turn on and off peripherals such as CD-ROMs,
network cards, hard disk drives and printers. This also includes consumer
devices connected to the PC such as VCRs, TVs, telephones and stereos.

In addition to enabling operating system-directed power management, ACPI pro­vides a generic system event mechanism for Plug and Play and an operating
system-independent interface for configuration control. ACPI leverages the Plug
and Play BIOS data structures while providing a processor architecture-indepen­dent implementation that is compatible with both Windows 98 and Windows NT

5.0.

Microsoft OnNow

The OnNow design initiative is a comprehensive, system-wide approach to sys­tem and device power control. OnNow is a term for a PC that is always on but
appears to be off and responds immediately to user or other requests.

Slow Blinking LED for Suspend-State Indicator

When the CPU goes into a suspend state, the power LED will start blinking to
indicate that the CPU is in suspend mode. When the user presses any key, the
CPU will wake-up and the LED will automatically stop blinking and remain on.

BIOS Support for USB Keyboard

If the USB keyboard is the only keyboard in the system, it will work like a normal
keyboard during system boot-up.

Real-Time Clock Wake-up Alarm

The PC may be perceived to be off when not in use, but is still capable of
responding to preset wake-up events. In the BIOS, the user can set a timer to
wake-up the system at a predetermined time (see page 5-14).

Chapter 1: Introduction

1-17

Main Switch Override Mechanism

When an ATX power supply is used, the power button can function as a system
suspend button. When the user depresses the power button, the system will
enter a SoftOff state. The monitor will be suspended and the hard drive will spin
down. Depressing the power button again will cause the whole system to wake­up. During the SoftOff state, the ATX power supply provides power to keep the
required circuitry on the system alive. In case the system malfunctions and you
want to turn off the power, just depress and hold the power button for 4 seconds.
The power will turn off and no power will be provided to the motherboard.

External Modem Ring-On

Wake-up events can be triggered by a device such as the external modem ringing
when the system is in SoftOff state. Note that the external modem ring-on can
only be used with an ATX 2.01 (or above) compliant power supply.

Wake-On-LAN (WOL)

Wake-On-LAN is defined as the ability of a management application to remotely
power up a computer that is powered off. Remote PC setup, updates and asset
tracking can occur after hours and on weekends so that daily LAN traffic is kept
to a minimum and users are not interrupted.

The motherboards have a 3-pin header (WOL) to connect to the 3-pin header on
a Network Interface Card (NIC) that has WOL capability. Note that Wake-On­LAN can only be used with an ATX 2.01 (or above) compliant power supply.

1-6 Power Supply Requirements

As with all computer products, a stable power source is necessary for proper and
reliable operation. This is even more important for the 400 MHz and higher clock
rates of Xeon processors.

The SUPER S2DG2/S2DGU/S2DGE/S2DGR accommodates ATX power sup­plies. Although most power supplies generally meet the specifications required
by the CPU, some are inadequate.

It is highly recommended that you use a high quality power supply that meets
ATX power supply Specification 2.01. Additionally, in areas where noisy power
transmission is present, you may choose to install a line filter to shield the

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

1-18

computer from noise. It is recommended that you also install a power surge
protector to help avoid problems caused by power surges.

1-7 Super I/O

The disk drive adapter functions of the Super I/O chip include a floppy disk drive
controller compatible with industry standard 82077/765, a data separator, write
pre-compensation circuitry, decode logic, data rate selection, a clock generator,
drive interface control logic and interrupt and DMA logic. The wide range of
functions integrated into the Super I/O greatly reduces the number of compo­nents required for interfacing with floppy disk drives. The Super I/O supports four
360 K, 720 K, 1.2 M, 1.44 M or 2.88 M disk drives and data transfer rates of 250
Kb/s, 500 Kb/s or 1 Mb/s.

It also provides two high speed serial communication ports (UARTs), one of which
supports serial infrared communication. Each UART includes a 16-byte send/
receive FIFO, a programmable baud rate generator, complete modem control
capability and a processor interrupt system. Both UARTs provide legacy speed
with baud rates of up to 115.2 Kbps as well as an advanced speed with baud rates
of 230 K, 500 K or 1 Mb/s, which support higher speed modems.

The Super I/O supports one PC-compatible printer port (SPP), Bi-directional
Printer Port (BPP), Enhanced Parallel Port (EPP) or Extended Capabilities Port
(ECP). Extension FDD and Extension 2FDD Modes are also available through
the printer port interface pins to allow one or two external floppy disk drives to
be connected.

The Super I/O provides functions that comply with ACPI (Advanced Configuration
and Power Interface), which includes support of legacy and ACPI power manage­ment through SMI or SCI function pins. It also features auto power management
to reduce power consumption.

The Super I/O complies with the Microsoft PC98 Hardware Design Guide.
IRQs, DMAs and I/O space resources can flexibly adjust to meet ISA PnP
requirements. Moreover, it meets the specification of PC98's power management
requirement: ACPI and APM (Advanced Power Management).

Chapter 1: Introduction

1-19

1-8 AIC-7890 Ultra2 SCSI Controller (S2DGU)

Note: If you are using a low voltage differential hard drive, it is recommended that you use an
LVD/SE Ultra2 SCSI cable. LVD/SE cables offer increased length and can accommodate up to
15 devices.

The SUPER S2DGU has an onboard Adaptec SCSI controller that is 100%
compatible with all major operating and hardware platforms. The Adaptec AIC­7890 controller provides advanced PCI-to-SCSI Ultra2 SCSI host adapter features
in a 272-pin Ball Grid Array (BGA) package, as well as containing an integrated
dual mode (LVD/SE) transceiver. The AIC-7890 Ultra2 SCSI chip connects to a
32-bit PCI bus. It is PCI 2.1 compliant and fully supports the power management
requirements specified in the Microsoft PC98 guidelines. The AIC-7890 functions
with Adaptec RAIDport III (ARO-1130C) to deliver RAID functionality.

The AIC-7890 Ultra2 SCSI controller, used together with the AIC-3860 trans­ceiver, allows Ultra2 and single-ended devices to operate together on the same
SCSI bus without inpacting Ultra2 performance and cable lengths. Connectors
on the S2DGU include one 68-pin 16-bit Ultra2 SCSI connector (JA1), one 68-pin
16-bit Ultra Wide SCSI connector (JA2) and one 50-pin 8-bit SCSI connector
(JA4). The controller allows you to connect a total of 15 SCSI devices, with a
maximum of 7 devices on the 50-pin SCSI connector.

1-9 AIC-7895 Dual Channel Ultra Wide SCSI Controller

(S2DGR)

The SUPER S2DGR has an onboard Adaptec SCSI controller that is 100%
compatible with all major operating and hardware platforms. PCI 2.1 compliance
is assured. Two independent Ultra Wide SCSI channels provide a data transfer
rate of 40 Mbytes/sec per channel. Connectors on the S2DGR include two 68­pin 16-bit Ultra Wide SCSI connectors (JA1/JA2) and one 50-pin 8-bit SCSI
connector (JA3). The controller allows you to connect a total of 30 SCSI devices
(15 for each channel), with a maximum of 7 devices on the 50-pin SCSI connec­tor.

The AIC-7895 consolidates the functions of two SCSI chips, eliminating the need
of a PCI bridge. Reducing PCI bus loading allows you to expand your system
capabilities with additional PCI devices.

The AIC-7895 functions with Adaptec RAIDport II (ARO-1130SA/1130CA) to de­liver RAID functionality. For information on installing onboard SCSI under Win­dows NT, refer to page 3-6 in the FAQ section of this manual.

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

1-20

1-10 AIC-7896 Ultra2 Dual Channel SCSI Controller

(S2DG2)

The SUPER S2DG2 has an onboard Adaptec SCSI controller that is 100% com­patible with all major operating and hardware platforms. PCI 2.1 compliance is
assured.

The AIC-7896 Ultra2 SCSI chip connects to a 32-bit PCI bus. Two independent
Ultra2 LVD SCSI channels provide a per channel data transfer rate of 80 MB/s.
Connectors on the S2DG2 include two 68-pin 16-bit Ultra2 SCSI connectors (JA1
and JA2) and one 50-pin 8-bit SCSI connector (JA3). The controller allows you
to connect a total of 30 SCSI devices (15 for each channel), with a maximum of
7 devices on the 50-pin SCSI connector.

The AIC-7896 consolidates the functions of two SCSI chips to eliminate the need
of a PCI bridge. Reducing PCI bus loading enables system capabilities to be
expanded with additional PCI devices. The AIC-7896 functions with Adaptec
RAIDport III (ARO-1130C) to deliver dual channel RAID functionality.

The AIC-7896 SCSI host adapter meets the highest performance requirements of
today. It can deliver Ultra2 SCSI data transfer rates of up to 80 Mbytes/sec per
channel, for a total throughput of 160 Mbytes/sec. It was designed to meet the
needs of bandwidth-hungry applications, such as high-level simulations, real-time
video and data mining.

Chapter 2: Installation

2-1

Chapter 2

Installation

2-1 Static-Sensitive Devices

Static-sensitive electrical discharge can damage electronic components. To
prevent damage to your system board, it is important to handle it very carefully.
The following measures are generally sufficient to protect your equipment from
static discharge.

Precautions

• Use a grounded wrist strap designed to prevent static discharge.

• Touch a grounded metal object before you remove the board from the antistatic
bag.

• Handle the board by its edges only; do not touch its components, peripheral
chips, memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the system board and peripherals back into their antistatic bags when not
in use.

• For grounding purposes, make sure your computer system’s chassis provides
excellent conductivity between the power supply, the case, the mounting
fasteners and the system board.

Unpacking

The system board is shipped in antistatic packaging to avoid static damage.
When unpacking the board, be sure the person handling the board is static­protected.

2-2 Pentium II and III Xeon Processor Installation

When handling the Pentium II/III Xeon processor, avoid placing
direct pressure to the label area of the fan.

!

When installing the Pentium II/III Xeon processor, the DRM (Dual
Retention Module) must be bolted to the chassis. This provides
the processor with support against shock and vibration.

!

Note: These instructions are for the retail pack with a passive heatsink.
OEM Pentium II/III Xeon processors also require a heat sink (not included).

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

2-2

1. Installing the metal standoffs:

Attach the metal standoffs to the back of the motherboard tray. Be sure
the location of all the mounting holes for both the motherboard and the
chassis match. Make sure the metal standoffs click in or are screwed
in tightly. There are three additional metal standoffs, specifically for the
Slot 2 motherboard, that are required for mounting the DRM (Dual
Retention Module). See Figure 2-1 for mounting hole locations.

2. Mounting the motherboard onto the motherboard tray:

Except for the four Slot 2 mounting holes, use a Philips screwdriver to
first secure the motherboard onto the motherboard tray.

3. Mounting the fans and the Dual Retention Module (See Figure 2-2):
Before mounting the retention base, you first need to mount the fans in
their proper locations. Screw the base retention parts into the four Slot
2 mounting holes.

Note: The DRM needs to be bolted through the

motherboard to the chassis.

4. Placing the fasteners:

Place a fastener on top of each side of the base, with the arm on top
and the screw holes underneath.

5. Installing caps on the Xeon processor as a handlebar:

When attaching the caps for each Xeon processor, make sure the
directions of the mounting screw holes on each cap face the inside so
that the CPU unit can easily slide in. Please test the configuration of
the units before mounting the caps.

6. Securing the processor:

Slide in the single/dual processor(s) making sure it sits on the Slot 2
socket. Then, insert four of the screws included in the DRM kit and
secure the fastener down tightly.

Removing the Pentium II/III Xeon Processor

To remove the Pentium II/III processor from the motherboard, follow the reverse
of the installation process.

When removing the Pentium II/III processor, avoid pressing down
on the motherboard or components.

!

Chapter 2: Installation

2-3

Extra for Slot 2

Figure 2-1. Dual Retention Module Mounting Holes

ATX Standard

Hole

Extra for

Slot 2

Extra for Slot 2

*Back view of motherboard

When mounting the
motherboard to the
chassis, note that
you will use three
holes specifically for
mounting the Slot 2
DRM as well as one
ATX Standard hole
to secure the Slot 2
DRM.

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

2-4

3 2 1

Connector

Pins

Jumper

Cap

Setting

Pins 1-2

shorted

Example of 4.0

CPU Core/Bus Ratio

JB1 JB2 JB3 JB4

ON ON OFF ON

2-3 Explanation and
Diagram of Jumper/

Connector

To modify the operation of the moth­erboard, jumpers can be used to
choose between optional settings.
Jumpers create shorts between two
pins to change the function of the
connector. Pin 1 is identified with a
square.

2-4 Changing the CPU
Speed

To change the CPU speed for a
Pentium II/III processor, change the
jumpers as shown in Table 2-1. The
example on the right will show you
which CPU Core/Bus Ratio to use.
The general rule is to divide the CPU
speed by the bus speed (100 MHz).
If you have a 400 MHz CPU, dividing
it by 100 will give you a CPU Core/
BUS Ratio of 4.0. After determining
the CPU Core/Bus Ratio, refer to
Table 2-1 for the proper settings of
JB1, JB2, JB3 and JB4.

400 MHz = 100 MHz x 4.0
CPU Speed = Bus Freq. x Ratio

CPU Core/

Bus Ratio

3.0

3.5

4.0

4.5

5.0

5.5

6.0

6.5

7.0

7.5

JB1
ON

OFF

ON

OFF

ON

OFF

ON

OFF

ON

OFF

JB2
OFF
OFF

ON

ON
OFF
OFF

ON

ON
OFF
OFF

JB3

ON

ON
OFF
OFF
OFF
OFF

ON

ON

ON

ON

JB4

ON
ON
ON
ON
ON

ON
OFF
OFF
OFF
OFF

Table 2-1

Pentium II/III Speed Selection

Chapter 2: Installation

2-5

2-5 Mounting the Motherboard in the Chassis

All the motherboards have standard mounting holes to fit different types of chas­sis. Chassis may come with a variety of mounting fasteners made of metal or
plastic. Although a chassis may have both metal and plastic fasteners, metal
fasteners are the most highly recommended because they ground the system
board to the chassis. Therefore, use as many metal fasteners as possible for
better grounding.

2-6 Connecting Cables

Power Supply Connector

After you have securely mounted the
motherboard to the chassis, you are
ready to connect the cables. Attach
a power supply cable to J32 for ATX
power. The S2DG2 has two primary
power supply connectors: J32A and
J32B. You should use both prima­ries

and

the secondary connector if
included with your power supply.
See Table 2-2 for pin definitions.

Table 2-2

ATX Power Supply Connector

J32

Pin Number Definition
1 3.3V
2 3.3V3
3 Ground
4 5V
5 Ground
6 5V
7 Ground
8 PW-OK
9 5VSB
10 12 V

Pin Number Definition
11 3.3V
12 -1 2V
13 Ground
14 PS-ON
15 Ground
16 Ground
17 Ground
18 -5 V
19 5 V
20 5 V

Infrared Connector

The header for the infrared connector
is located on pins 1-5 of JF2. See
Table 2-4 for pin definitions.

Table 2-3

Secondary Power Connector

J36

Pin
Number Definition
1 Ground
2 Ground
3 Ground
4 +3.3V
5 +3.3V
6 +5V (keyed)

Secondary Power Connector

Use of the Secondary Power Con­nector (PWR_SEC) is recommended
when a heavy load of peripherals has
been added to the motherboard.

Note: Be sure to use a 6-pin connector
and check the power supply layout before
attaching it.

The Secondary Power
Connector is located on J36. See
Table 2-3 for pin definitions.

Pin

Number

1
2
3
4
5

Definition

+5V
Key

IRRX

Ground

IRTX

Table 2-4

Infrared Header

JF2

Note: The S2DG2 has two primary power supply connectors

located at J32A and J32B.

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

2-6

PW_ON Connector

The header for the PW_ON connec­tor is located on pins 9 and 10 of
JF2. Momentarily contacting both
pins will power on/off the system.
The user can also configure this but­ton to function as a suspend button.
(See BIOS setup information on
page 5-12). To turn off the power
when set to suspend mode, hold
down the power button for at least 4
seconds. See Table 2-5 for pin defi­nitions.

Reset Connector

The header for the reset connector is
located on pins 12 and 13 of JF2.
This is used for the hardware reset
switch on the computer case. See
Table 2-6 for pin definitions.

Pin

Number

9

10

Definition

PW_ON

Ground

Table 2-5

PW_ON Header

JF2

Table 2-7

Hard Drive LED

Header

JF1

Pin

Number

1
2
3
4

Definition

+5V
HD Active
HD Active

+5V

Pin

Number

12
13

Definition

Ground

Reset

Table 2-6

Reset Header

JF2

Hard Drive LED

The header for the hard drive LED is
located on pins 1 to 4 of JF1. Attach
the hard drive LED cable to pins 1
and 2. See Table 2-7 for pin defini­tions.

Keylock/Power LED
Connector

The header for the keylock/power
LED connector is located on pins 5
to 9 of JF1. Pins 5 through 7 are for
the power LED and pins 8 and 9 are
for the keylock. See Table 2-8 for
pin definitions.

Pin

Number

5
6
7
8
9

Function
VCC +5V
VCC +5V

Ground
Ground

Table 2-8

Keylock/Power LED Header

JF1

Definition
Red wire, LED power
Red wire, LED power

LED control

Keyboard inhibit

Black wire

Chapter 2: Installation

2-7

Jumper

Position

1-2
2-3

Definition
PIIX4 Ctrl

Save PD State

Table 2-10

Power Save State Select

JP20

Position

1-2

Position

2-3

PIIX4 Ctrl

Save PD State

Table 2-9

Speaker Header

JF1

Pin

Number

10
11
12
13

Function

+

Key

Definition

Red wire, Speaker data

No connection

Key

Speaker data

Speaker Connector

The header for the speaker connec­tor is located on pins 10 to 13 of JF1.
See Table 2-9 for pin definitions.

Power Save State Select

Refer to Table 2-10 to set JP20. The
Power Save State is used when you
want the system to remain in the
power-off state when you first apply
power to the system or when the
system recovers from an AC power
failure. In this state, the power will
not come on unless you hit the
power switch on the motherboard.
PIIX4 control is used if you want the
system to be in the power-on state
the first time you apply power to the
system or when the system recovers
from an AC power failure.

Table 2-11

ATX PS/2

Keyboard

and Mouse Ports

J34

Pin

Number

1
2
3
4
5
6

Definition

Data

NC

Ground

VCC

Clock

NC

Universal Serial Bus

The two Universal Serial Bus con­nectors are located on J17 and J18.
See Table 2-12 for pin definitions.

Table 2-12

Universal Serial Bus

Pin
Number Definition
1 +5V
2 P0­ 3 P0+
4 Ground
5 N/A

Pin
Number Definition
1 +5V
2 P0­ 3 P0+
4 Ground
5 Key

J17

J18

ATX PS/2 Keyboard and
Mouse Ports

The ATX PS/2 keyboard and the PS/
2 mouse ports are located on J34.
See Table 2-11 for pin definitions.

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

2-8

Table 2-14

CMOS Clear

JBT1

Jumper

Position

1-2
2-3

Definition

Normal

CMOS Clear

CMOS Clear

Refer to Table 2-14 for instructions
on how to clear CMOS. For an ATX

power supply, you need to com­pletely shut down the system,
and then use JBT1 to clear CMOS.
Do not use the PW_ON connector
to clear CMOS. A second way of

resetting the CMOS contents is by
pressing the <Ins> key and then
turning on the system power. Re­lease the key when the power comes
on.

ATX Serial Ports

ATX serial port COM1 is located
on J20 and serial port COM2 is
located on J21. See Table 2-13
for pin definitions.

Wake-On-LAN

The Wake-On-LAN connector is lo­cated on WOL. Refer to Table 2-16
for pin definitions.

Position

1-2

Position

2-3

Normal

CMOS Clear

Table 2-13

ATX Serial Ports

Pin Number Definition
1 DCD
2 D S R
3 Serial In
4 RT S
5 Serial Out

Pin Number Definition
6 C T S
7 D T R
8 RI
9 Ground
10 N C

J20

J21

External Battery

Connect an external battery to JBT2.
Refer to Table 2-15 for pin defini­tions.

Pin

Number

1
2
3
4

Definition

+3V

NC

NC

Ground

Table 2-15

External Battery

JBT2

Pin

Number

1
2
3

Definition

+5V Standby

Ground

Wake up

Table 2-16

Wake-On-LAN

WOL

Fan Connectors*

The thermal/overheat fans are lo­cated on JT3 and JT3A. The CPU
fans are located on JT1, JT1A, JT2
and JT2A.

Note: JT1A, JT2A and

JT3A do not have tachometers.

Refer to Table 2-17 for pin defini­tions.

Table 2-17

Fan Connectors

JT1, JT1A, JT2, JT2A,

JT3 and JT3A

Pin

Number

1
2
3

Definition

Ground (black)

+12V (red)

Tachometer

* Caution: These fan connectors
are DC direct.

Note: JT1A, JT2A and JT3A do not have tachometers.

Chapter 2: Installation

2-9

Chassis Intrusion

The Chassis Intrusion Detector is
located on JL1. See the board lay­outs in Chapter 1 and the PC Health
Monitor information on page 1-14 for
more information. See Table 2-18 for
pin definitions.

Pin

Number

1
2

Definition

Intrusion Input

Ground

Table 2-18

Chassis Intrusion

JL1

2-7 Installing DIMMs

CAUTION

Exercise extreme care when installing or removing DIMMs to

prevent any possible damage.

DIMM Installation

1. Insert DIMM modules in Bank 0 through Bank 3 as required for the
desired system memory.

2. Insert each DIMM module vertically into its socket. Pay attention to the
notches along the bottom of the module to prevent inserting the DIMM
incorrectly.

3. Gently press down on the DIMM module until it snaps upright and into
place in the socket.

4. For best results, install DIMMs starting from Bank 0.

Open = Default Closed = Intrusion

SLED (SCSI LED) Indicator

The SLED connector is used to pro­vide an LED indication of SCSI activ­ity. Refer to Table 2-19 for connect­ing the SCSI LED.

Pin

Number

1
2
3
4

Definition

Positive
Negative
Negative

Positive

Table 2-19

SLED Pin Definitions

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

2-10

Top View of DIMM Socket

Figure 2-3. DIMM Installation

To Install:

Insert
vertically and
press down
until it snaps
into place.
Pay attention
to the two
notches.

To Remove:

Use your thumb to
gently push the
edge of the socket
and release the
module. Do this on
both sides for each
module.

Note: Notches

should align

with their

receptive points

on the socket

DIMM Socket

Side View of DIMM Installation into Socket

DIMM

PC100

Notches

PC100

Notches

2-8 Connecting the Parallel Port, Floppy and Hard Disk
Drives

Use the following information to connect the floppy and hard disk drive cables.

• The floppy disk drive cable has seven twisted wires.

• A red mark on a wire typically designates the location of pin 1.

• A single floppy disk drive ribbon cable has 34 wires and two connectors to
provide for two floppy disk drives. The connector with the twisted wires always
connects to drive A, and the connector without the twisted wires always
connects to drive B.

• An IDE hard disk drive requires a data ribbon cable with 40 wires, and a SCSI
hard disk drive requires a SCSI ribbon cable with 50 wires. A wide SCSI hard
disk drive requires a SCSI ribbon cable with 68 wires.

• A single IDE hard disk drive cable has two connectors to provide for two drives.
To designate an IDE disk drive as C, you would normally set the drive select
jumper on the drive to DS1 (or Master). To designate an IDE disk drive as D,
you would normally set the drive select jumper on the drive to DS2 (or Slave).
Consult the documentation that came with your disk drive for details on actual
jumper locations and settings.

• A single SCSI ribbon cable typically has three connectors to provide for two

Chapter 2: Installation

2-11

hard disk drives and the SCSI adapter. (Note: Most SCSI hard drives are
single-ended SCSI devices.) The SCSI ID is determined either by jumpers or
by a switch on the SCSI device. The last internal (and external) SCSI device
cabled to the SCSI adapter must be terminated.

Pin Number Function
1 Reset IDE
3 Host Data 7
5 Host Data 6
7 Host Data 5
9 Host Data 4
11 Host Data 3
13 Host Data 2
15 Host Data 1
17 Host Data 0
19 GN D
21 DRQ3
23 I/O Write­ 25 I/O Read­ 27 IOCHRDY
29 DACK3­ 31 IRQ14
33 Addr 1
35 Addr 0
37 Chip Select 0
39 Activity

Pin Number Function
2 GN D
4 Host Data 8
6 Host Data 9
8 Host Data 10
10 Host Data 11
12 Host Data 12
14 Host Data 13
16 Host Data 14
18 Host Data 15
20 K ey
22 GN D
24 GN D
26 GN D
28 BALE
30 GN D
32 IOCS16­ 34 GN D
36 Addr 2
38 Chip Select 1­ 40 GN D

Table 2-21

IDE Connectors J15 and J16

Pin Number Function
1 Strobe­ 3 Data Bit 0
5 Data Bit 1
7 Data Bit 2
9 Data Bit 3
11 Data Bit 4
13 Data Bit 5
15 Data Bit 6
17 Data Bit 7
19 A CK
21 BUSY
23 P E
25 SLCT

Pin Number Function
2 Auto Feed­ 4 Error­ 6 Init­ 8 SLCT IN­ 10 G N D
12 G N D
14 G N D
16 G N D
18 G N D
20 G N D
22 G N D
24 G N D
26 N C

Table 2-19

Parallel Port Connector J19

Parallel Port Connector

The parallel port is located on J19.
See Table 2-19 for pin definitions.

Pin Number Function
1 GN D
3 GN D
5 Ke y
7 GN D
9 GN D
11 GN D
13 GN D
15 GN D
17 GN D
19 GN D
21 GN D
23 GN D
25 GN D
27 GN D
29 GN D
31 GN D
33 GN D

Pin Number Function
2 FDHDIN
4 Reserved
6 FDEDIN
8 Index­ 10 Motor Enable
12 Drive Select B­ 14 Drive Select A­ 16 Motor Enable
18 DIR­ 20 STEP­ 22 Write Data­ 24 Write Gate­ 26 Track 00­ 28 Write Protect­ 30 Read Data­ 32 Side 1 Select­ 34 Diskette

Table 2-20

Floppy Connector J22

Floppy Connector

The floppy connector is located
on J22. See Table 2-20 for pin
definitions.

IDE Interfaces

There are no jumpers to configure
the onboard IDE interfaces J15
and J16. Refer to Table 2-21 for
pin definitions.

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

2-12

Pin Number Function
1 GN D
2 GN D
3 GN D
4 GN D
5 GN D
6 GN D
7 GN D
8 GN D
9 GN D
10 GN D
11 GN D
12 GN D
13 GN D
14 GN D
15 GN D
16 GN D
17 Termpwrd
18 Termpwrd
19 GN D
20 GN D
21 GN D
22 GN D
23 GN D
24 GN D
25 GN D
26 GN D
27 GN D
28 GN D
29 GN D
30 GN D
31 GN D
32 GN D
33 GN D
34 GN D

Pin Number Function
35 -DB (12)
36 -DB (13)
37 -DB (14)
38 -DB (15)
39 Parity H
40 -DB (0)
41 -DB (1)
42 -DB (2)
43 -DB (3)
44 -DB (4)
45 -DB (5)
46 -DB (6)
47 -DB (7)
48 Parity L
49 G N D
50 Termpwrd
51 Termpwrd
52 Termpwrd
53 N C
54 G N D
55 -A TT N
56 G N D
57 -BSY
58 -ACK
59 -RST
60 -MSG
61 -SEL
62 - CD
63 -REQ
64 -IO
65 -DB (8)
66 -DB (9)
67 -DB (10)
68 -DB (11)

Table 2-22

Ultra Wide SCSI Connector

Pin Number Function
1 GN D
2 GN D
3 GN D
4 GN D
5 GN D
6 GN D
7 GN D
8 GN D
9 GN D
10 GN D
11 GN D
12 Reserved
13 Open
14 Reserved
15 GN D
16 GN D
17 GN D
18 GN D
19 GN D
20 GN D
21 GN D
22 GN D
23 GN D
24 GN D
25 GN D

Table 2-23

50-Pin SCSI Connector

Pin Number Function
26 -DB (0)
27 -DB (1)
28 -DB (2)
29 -DB (3)
30 -DB (4)
31 -DB (5)
32 -DB (6)
33 -DB (7)
34 -DB (P)
35 G N D
36 G N D
37 Reserved
38 Termpwr
39 Reserved
40 G N D
41 -ATN
42 G N D
43 -BSY
44 -ACK
45 -RST
46 -MSG
47 -SEL
48 -C/D
49 -REQ
50 -I/O

SCSI Connectors

There are no jumpers to configure
the onboard, single-ended SCSI in­terface. Refer to Table 2-22 for the
Ultra Wide SCSI pin definitions. Re­fer to Table 2-23 for the 50-pin SCSI
pin definitions.

Chapter 2: Installation

2-13

Ultra2 LVD/SE SCSI
Connector

Refer to Table 2-24 for the
Ultra2 LVD/SE SCSI pin
definitions.

Signal Names

+DB(12)
+DB(13)
+DB(14)
+DB(15)
+DB(P1)

+DB(0)
+DB(1)
+DB(2)
+DB(3)
+DB(4)
+DB(5)
+DB(6)
+DB(7)
+DB(P)

GROUND

DIFFSENS
TERMPWR
TERMPWR

RESERVED

GROUND

+ATN

GROUND

+BSY
+ACK
+RST

+MSG

+SEL

+C/D

+REQ

+I/O
+DB(8)
+DB(9)

+DB(10)
+DB(11)

Connector

Contact
Number

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34

Signal Names

-DB(12)

-DB(13)

-DB(14)

-DB(15)

-DB(P1)

-DB(0)

-DB(1)

-DB(2)

-DB(3)

-DB(4)

-DB(5)

-DB(6)

-DB(7)

-DB(P)
GROUND
GROUND

TERMPWR
TERMPWR

RESERVED

GROUND

-ATN

GROUND

-BSY

-ACK

-RST

-MSG

-SEL

-C/D

-REQ

-I/O

-DB(8)

-DB(9)

-DB(10)

-DB(11)

Connector

Contact
Number

35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68

Table 2-24

Ultra2 LVD/SE SCSI Connector

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

2-14

AGP Port

There are no jumpers to
configure AGP port J8.
Refer to Table 2-25 for pin
definitions.

Pin #

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33

Pin #

34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66

B

Spare

5.0V

5.0V

USB+

GND

INTB#

CLK

REQ#

VCC3.3

ST0
ST2

RBF#

GND

Spare

SBA0

VCC3.3

SBA2

SB_STB

GND
SBA4
SBA6

KEY
KEY
KEY

KEY
AD31
AD29

VCC3.3

AD27
AD25

GND

AD_STB1

AD23

A

12V

Spare

Reserved*

USB-

GND

INTA#

RST#

GNT#

VCC3.3

ST1

Reserved

PIPE#

GND

Spare

SBA1

VCC3.3

SBA3

Reserved

GND
SBA5
SBA7

KEY
KEY
KEY

KEY
AD30
AD28

VCC3.3

AD26
AD24

GND

Reserved

C/BE3#

B

Vddq3.3

AD21
AD19

GND

AD17

C/BE2#

Vddq3.3

IRDY#

GND

VCC3.3

DEVSEL#

Vddq3.3

PERR#

GND

SERR#

C/BE1#

Vddq3.3

AD14
AD12

GND

AD10

AD8

Vddq3.3

AD_STB0

AD7

GND

AD5
AD3

Vddq3.3

AD1

SMB0

A

Vddq3.3

AD22
AD20

GND
AD18
AD16

Vddq3.3
Frame#

GND

VCC3.3

TRDY#
STOP#

Spare

GND

PAR

AD15

Vddq3.3

AD13
AD11

GND

AD9
C/BE0#
Vddq3.3

Reserved

AD6

GND

AD4

AD2
Vddq3.3

AD0

SMB1

Table 2-25

AGP Port J8

3-1

Chapter 3: Troubleshooting

Chapter 3

Troubleshooting

3-1 Troubleshooting Procedures

Use the following procedures and chart to troubleshoot your system. If you have
followed all the procedures below and still need assistance, refer to the ‘Tech­nical Support Procedures’ and/or ‘Returning Merchandise for Service’ section(s)
in this chapter.

Before Power On

1. Make sure no short circuits exist between the motherboard and chassis.

2. Disconnect all ribbon/wire cables from the motherboard.

3. Remove all add-on cards except for the video/graphics card. (Be sure
the video/graphics card is inserted properly.)

4. Install a CPU, the chassis speaker and the power LED to the mother­board. (Check all jumper settings as well.)

5. Install a memory module into one bank.

6. Check the power supply voltage monitor 115V/230V switch.

Power On

System Power

LED on?

System

Halts?

Speaker

Beeps?

Speaker

Beeps?

Number of

Beeps

Video

Display?

Power

Supply OK?

Speaker

Beeps?

Remove

Memory

Check CPU &

BIOS

Replace

Motherboard

Replace Power

Supply

Check BIOS

Settings &

Add-on Cards

Motherboard

Good

Memory

Problem:

Check Memory

Video Card

Problem

N

N

N

N

N

N

N

Y

Y

Y

Y

Y

6

8

Y

Y

*

See "Before Power On",
above, before proceeding
with these steps.

Figure 3-1. Troubleshooting Flowchart

3-2

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

No Power

1. Make sure that the default jumper is on and the CPU is correctly set up.

2. Turn the power switch on and off to test the system.

3. If the power is still not on, turn the system power off and change the
jumper setting on JP20 from 2-3 to 1-2.

4. If changing the jumper setting has not helped, clear CMOS.

5. Check the power supply voltage monitor. (Check the power supply
115V/230V switch.)

No Video

Use the following steps to troubleshoot your system configuration.

1. If the power is on but you have no video, remove all the add-on cards
and cables.

2. Check for shorted connections, especially under the motherboard.

3. Check the jumpers settings, clock speed and voltage settings.

4. Use the speaker to determine if any beep codes exist. Refer to
Appendix A for details on beep codes.

NOTE

If you are a system integrator, VAR or OEM, a POST diagnostics

card is recommended. For port 80h codes, refer to Appendix B.

Memory Errors

If you encounter memory errors, follow the procedures below.

1. Check to determine if the DIMM modules are improperly installed.

2. Make sure that different types of DIMMs have not been installed in
different banks (e.g., a mixture of 2 MB x 36 and 1 MB x 36 DIMMs in
Bank 0).

3. Determine if DIMMs of different speeds have been installed and verify
that the BIOS setup is configured for the fastest speed of RAM used. It
is recommended to use the same RAM speed for all DIMMs in the
system.

4. Check for bad DIMM modules or chips.

5. Try to install the minimum amount of memory first (a single bank).

3-3

Chapter 3: Troubleshooting

Losing the System’s Setup Configuration

1. Check the setting of jumper JBT1. Ensure that you are using a high

quality power supply. A poor quality power supply may cause the
system to lose the CMOS setup. Refer to Chapter 1 of this manual for
details.

2. If the above step does not fix the Setup Configuration problem, contact
your vendor for repairs.

3-2 Technical Support Procedures

1. Please go through the ‘Troubleshooting Procedures’ and 'Frequently Asked
Question' (FAQ) sections in this chapter of the manual or check our web site
FAQ (http://www.supermicro.com) before contacting Technical Support.

2. Take note that as a motherboard manufacturer Super Micro does not sell
directly to end-users, so it is best to check with your distributor or reseller
for troubleshooting services. They should know of any possible problem(s)
with the specific system configuration that was sold to you.

3. BIOS upgrades can be downloaded from the SUPER BBS# [phone],
24 hours a day, using 1200-28800 baud, 8 data bits, 1 stop bit and no parity.
BIOS upgrades can also be downloaded from our web site at http://
www.supermicro.com.

Note: Not all BIOS can be flashed depending on the modifications to the
boot block code.

4. If you still cannot resolve the problem, include the following information when
you e-mail Super Micro for technical support:

•BIOS release date/version

• System board serial number

•Product model name

•Invoice number and date

•System configuration
Due to the volume of e-mail we receive and the time it takes to replicate
problems, a response to your question may not be immediately available.
Please understand that we do not have the resources to serve every end­user, however, we will try our best to help all of our customers.

5. Distributors: For immediate assistance, please have your account
number ready when placing a call to our technical support department.

3-4

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

3-3 Frequently Asked Questions

Question: Do I need to change any settings to use a single processor on
a dual processor board?

Answer: There are no jumpers or BIOS settings that need to be changed when

running a single CPU on a dual processor board. Also, you can use a single
processor in either slot.

Question: What are the differences between the various memories that
the 440GX motherboard can support?

Answer: The 440GX integrates a main memory DRAM controller that supports

64-bit or 72-bit (64 bit memory data plus 8 ECC bits) DRAM for 8 MB to 512 MB
of SDRAM and 8 MB to 2 GB of SDRAM/registered DIMMs. The DRAM types
supported are either Synchronous DRAM (SDRAM) or registered DIMMs.

1. Mixing ECC and non-ECC memory will result in non-ECC operation.

EC/ECC is supported properly in the 440GX only if all memory is 72 bits
wide. A system with a mixture of 64- and 72-bit wide memory will disable
ECC mode.

2. Registered SDRAM and unbuffered SDRAM cannot be mixed.

3. Mixing PC/100 DIMM and PC/66 DIMM will result in an unexpected
memory count or system errors.

4. User should populate memory starting with the DIMM socket located
furthest from the GX chip (slot J4).

Question: How do I update my BIOS?

Answer: It is recommended that you do not upgrade your BIOS if you are

experiencing no problems with your system. Updated BIOS files are located on
our web site at http://www.supermicro.com. Please check our BIOS warning
message and the info on how to update it. Also, check the current BIOS revision
and make sure it is newer than your BIOS before downloading. Select your
motherboard model and download the proper BIOS file to your computer. Unzip
the BIOS update file and you will find the readme.txt (flash instructions), the
sm2flash.com (BIOS flash utility) and the BIOS image (xxxxxx.rom) files. Copy
these files onto a bootable floppy disk and reboot your system. It is not neces­sary to set BIOS boot block protection jumpers on the motherboard. At the DOS

3-5

Chapter 3: Troubleshooting

prompt, enter the command "sm2flash." This will start the flash utility and give
you an opportunity to save your current BIOS image. Flash the boot block and
enter the name of the update BIOS image file. NOTE: It is important to save your
current BIOS and rename it "super.rom" in case you need to recover from a failed
BIOS update. Select flash boot block, then enter the update BIOS image. Select
"Y" to start the BIOS flash procedure and do not disturb your system until the
flash utility notifies you that the procedure is complete. After updating your
BIOS, clear CMOS and then load the Optimal Values into BIOS.

Question: After flashing the BIOS, my system does not have video. How
can I correct this?

Answer: If the system does not have video after flashing your new BIOS, it

indicates the flashing procedure failed. To remedy this, first clear the CMOS per
the instructions in this manual and retry the BIOS flashing procedure. If you still
do not have video, please use the following BIOS Recovery Procedure. Turn
your system off and place the floppy disk with the saved BIOS image file (see
above FAQ) in drive A. Depress and hold "CTRL" and "Home" at the same time,
then turn on the power keeping these keys depressed until your floppy drive
starts reading. Your screen will remain blank until the BIOS program is done.
If the system reboots correctly, the recovery was successful. The BIOS Recov-

ery Procedure wii not update the boot block in your BIOS.

Question: I have memory problems. What is the correct memory to use
and which BIOS setting should I choose?

Answer: The correct memory to use for the SUPER S2DG2/S2DGU/S2DGE/

S2DGR is 168-pin DIMMs of 3.3v non-buffered SPD (Serial Present Detection)
SDRAM and SDRAM. SPD SDRAM is preferable but not essential. IMPOR­TANT: Please do not mix memory types; the results are unpredictable. If your
memory count is exactly half of the correct value, go to the Chipset Setup in
BIOS and set "SDRAM AUTOSIZING SUPPORT" to

Enabled

. Switch between

the available options until one setting correctly displays your memory.

Question: Which Operating Systems (OS) supports AGP?

Answer: At present, Windows 98 and Windows NT 5.0 are the only OS that have

built-in support for AGP. Some AGP video adapters can run under Windows 95
OSR2.1 with special drivers. Please contact your graphics adapter vendor for
more details.

3-6

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

Question: Do I need the CD that came with your motherboard?

Answer: The supplied compact disc has quite a few drivers and programs that

will greatly enhance your system. We recommend that you review the CD and
install the applications you need. Applications included on the CD are PCI IDE
Bus Master drivers for Windows 95 and Windows NT, 440GX chipset drivers for
Windows 95 and 98, and the Super Doctor monitoring software.

Question: How do I install an onboard SCSI device controller for my
S2DG2/S2DGU/S2DGR motherboard?

Answer: First, install the 3 NT installation disks and follow the onscreen instruc-

tions to complete the procedure. "Safe mode" is best for this installation.

Question: Why can't I turn off the power using the momentary power on/
off switch?

Answer: The instant power off function is controlled by the BIOS (page 5-12).

When this feature is enabled in the BIOS, the motherboard will have "instant off"
capabilities as long as the BIOS has control of the system. When this feature
is disabled or when the BIOS is not in control, such as during the memory count
(the first screen that appears when the system is turned on), the momentary on/
off switch must be held for more than four seconds to shut the system down. This
feature is required to implement the ACPI features on the motherboard.

Question: I see some of my PCI devices sharing IRQs, but the system
seems to be fine. Is this correct or not?

Answer: Some PCI Bus Mastering devices can share IRQs without performance

penalties. These devices are designed to work correctly while sharing IRQs.

Question: When I connect my Ultra2 LVD hard drive to the JA1 SCSI con­nection, the drive is not recognized by BIOS or it fails to boot. Do I need
a special cable?

Answer: Yes, for an Ultra2 LVD drive, you need a special 68-pin cable with active

termination at the end of the cable, since Ultra2 LVD hard drives do not have a
termination on the drive.

3-7

Chapter 3: Troubleshooting

This warranty only covers normal consumer use and does not cover damages
incurred in shipping or from failure due to the alternation, misuse, abuse or
improper maintenance of products.

During the warranty period, contact your distributor first for any product prob­lems.

3-4 Returning Merchandise for Service

A receipt or copy of your invoice marked with the date of purchase is required
before any warranty service will be rendered. You can obtain service by calling
your vendor for a Returned Merchandise Authorization (RMA) number. When
returning to the manufacturer, the RMA number should be prominently displayed
on the outside of the shipping carton and either mailed prepaid or hand-carried.
Shipping and handling charges will be applied for all orders that must be mailed
when service is complete.

3-8

SUPER S2DG2/S2DGU/S2DGE/S2DGR Manual

Notes

Chapter 4: AMIBIOS

4-1

Chapter 4

AMIBIOS

4-1 Introduction

This chapter describes the AMIBIOS for Intel 440GX Pentium II/III Xeon proces­sors. The AMI ROM BIOS is stored in the Flash EEPROM and can be easily
upgraded using a floppy disk-based program.

System BIOS

The BIOS is the Basic Input Output System used in all IBM® PC, XT™, AT®, and
PS/2® compatible computers. WinBIOS is a high-quality example of a system
BIOS.

Configuration Data

AT-compatible systems, also called ISA (Industry Standard Architecture), must
have a place to store system information when the computer is turned off. The
original IBM AT had 64 kbytes of non-volatile memory storage in CMOS RAM. All
AT-compatible systems have at least 64 kbytes of CMOS RAM, which is usually
part of the Real-Time Clock. Many systems have 128 kbytes of CMOS RAM.

How Data Is Configured

AMIBIOS provides a Setup utility in ROM that is accessed by depressing <Del>
at the appropriate time during system boot. This Setup utility configures the data
in CMOS RAM.

POST Memory Test

Normally, the only visible POST routine is the memory test. The screen that
appears when the system is powered on is shown on the next page.

An AMIBIOS identification string is displayed at the left bottom corner of the
screen, below the copyright message.

BIOS User's Manual

4-2

Checking NVRAM
xxxxx KB OK

Hit <DEL> if you want to run SETUP

(C) Super Micro Computer, Inc.,
XX-XXXX-XXXXXX-XXXXXXXX-XXXXXX-XXXX-X

4-2 BIOS Features

• Supports Plug and Play v 1.0A and DMI 2.1

• Supports Intel PCI 2.1 (Peripheral Component Interconnect) local bus
specification

• Supports Advanced Power Management (APM) Specification v 1.1

• Supports ACPI

• Supports Flash ROM

AMIBIOS supports the LS120 drive made by Matsushita-Kotobuki Electronics
Industries Ltd. The LS120:

• Can be used as a boot device

• Is accessible as the next available floppy drive

AMIBIOS supports PC Health Monitoring chips. When a failure occurs in a
monitored activity, AMIBIOS can sound an alarm and display a message. The
PC Health Monitoring chips monitor:

• CPU temperature

• Additional temperature sensors

• Chassis intrusion detector

American

Mega

Trends

S

UPER

AMIBIOS (c) 1997 American Megatrends, Inc.
0404981500 Pentium II Motherboard Made in USA R1.0

BIOS revision code

BIOS date code

Chapter 4: AMIBIOS

4-3

AMIBIOS System Configuration (C) 1985-1997 American Megatrends Inc.,

Main Processor : Pentium(tm) II Base Memory Size : 640 KB

BIOS Configuration Summary Screen

AMIBIOS displays a screen that looks similar to the following when the
POST routines complete successfully.

Math Processor : Built-In Ext. Memory Size : 64512 KB
Floppy Drive A: : 1.44 MB, 31/

2

Display Type : VGA/EGA
Floppy Drive B: : None Serial Port(s) : 3F8, 2F8
AMI-BIOS Date : 7/15/95 Parallel Port(s) : 378
Processor Clock : 350MHz External Cache : 512 KB

PCI Devices
PCI Onboard PCI Bridge PCI Onboard Bridge Device
PCI Onboard USB Controller PCI Onboard IDE
PCI Onboard SCSI, IRQ 10 PCI Onboard SCSI, IRQ 10
PCI Slot 4 VGA, IRQ 11

AMIBIOS Setup

See the following page for examples of the AMIBIOS Setup screen, which
features options and settings. Figure 4-1 shows the

Standard

option
highlighted. To highlight other options, use the arrow keys or the tab key to
move to other option boxes. Figure 4-2 shows the settings for the Standard
setup. Settings can be viewed by highlighting a desired option and pressing
<Enter>. Use the arrow keys to choose a setting. Note: Optimal settings
for all options can be set automatically. Go to the

Optimal

icon in the

default box and press <Enter>. Use the arrow keys to highlight

Yes,

then

press <Enter>.

*Note: The picture above reflects a board equipped with SCSI, but may be taken as a general example.

• Five positive voltage inputs

• Two negative voltage inputs

• Three fan speed monitor inputs

BIOS User's Manual

4-4

Figure 4-1. AMIBIOS Hiflex Setup Utility Screen

AMIBIOS Hiflex Setup Utility - Version 1.18

(C)1998 American Megatrends, Inc. All Rights Reserved

Standard CMOS Setup

Advanced CMOS Setup

Advanced Chipset Setup
Power Management Setup
PCI / Plug and Play Setup

Peripheral Setup

Auto-Detect Hard Disks

Change User Password

Change Supervisor Password

Change Language Setting

Auto Configuration with Optimal Settings

Auto Configuration with Fail Safe Settings

Save Settings and Exit

Exit Without Saving

Advanced CMOS setup for configuring system options

ESC: Exit ||: Sel F2/F3: Color F10: Save & Exit

Chapter 5: Running Setup

5-1

Chapter 5

Running Setup

Optimal and Fail-Safe default settings are in bold text unless otherwise noted.

The AMIBIOS Hiflex Setup options described in this section are selected by
choosing the appropriate high-level icon from the Standard Setup screen. All
displayed icons are described in this section, although the screen display is
often all you need to understand how to set the options.

5-1 Setup

5-1-1 Standard CMOS Setup

Date and Time Configuration

Select the Standard option. Select the

Date/Time

icon. The current values

for each category are displayed. Enter new values through the keyboard.

Floppy A
Floppy B

Choose the Floppy Drive A or B icon to specify the floppy drive type. The
settings are

Not Installed, 360 KB 5¼ inch, 1.2 MB 5¼ inch, 720 KB 3½

inch, 1.44 MB 3½ inch

or

2.88 MB 3½ inch

.

Note: The Optimal and Fail­Safe settings for Floppy Drive A are 1.44 MB 3 1/2 inch and for Floppy
Drive B are Not Installed

.

Pri Master
Pri Slave
Sec Master
Sec Slave

Select these options to configure the drive named in the option. Select

Auto

Detect IDE

to let AMIBIOS automatically configure the drive. A screen with a

list of drive parameters appears. Click on OK to configure the drive.

BIOS User's Manual

5-2

Boot Sector Virus Protection

The settings for this option are

Enabled

or

Disabled

.

Entering Drive Parameters

You can also enter the hard disk drive parameters. The drive parameters are:

Type How to Configure
1-46 Predefined types.
USER Enter parameters manually.
AUTO Set parameters automatically on each boot.
CDROM Use for ATAPI CDROM drives.
ARMD Use for LS120, MO, IOMEGA Zip drives.

Parameter Description
Type The number for a drive with certain identification parameters.
Cylinders The number of cylinders in the disk drive.
Heads The number of heads.
Write The size of a sector gets progressively smaller as the track

Precompensation diameter diminishes. Yet each sector must still hold 512 bytes.

Write precompensation circuitry on the hard disk compensates for
the physical difference in sector size by boosting the write current
for sectors on inner tracks. This parameter is the track number
where write precompensation begins.

Sectors The number of sectors per track. MFM drives have 17 sectors per

track. RLL drives have 26 sectors per track. ESDI drives have 34
sectors per track. SCSI and IDE drive may have even more sectors
per track.

Capacity The formatted capacity of the drive is (Number of heads) x

(Number of cylinders) x (Number of sectors per track) x (512

bytes per sector).
LBA Mode Enables support for IDE Drives with capacity greater than 528 MB.
BLK Mode Supports IDE Drives that use block mode.
PIO Mode
32-bit Mode 32-bit transfer (should be enabled only if supported by controller).

Chapter 5: Running Setup

5-3

5-1-2 Advanced CMOS Setup

Quick Boot

The Settings are

Disabled

or

Enabled

. Set to

Enabled

to permit AMIBIOS to

boot quickly when the computer is powered on. This option replaces the old
Above 1 MB Memory Test Advanced Setup option. The settings are:

Setting Description

Disabled

AMIBIOS tests all system memory. AMIBIOS waits
for up to 40 seconds for a READY signal from the
IDE hard disk drive. AMIBIOS waits for .5 seconds
after sending a RESET signal to the IDE drive to
allow the IDE drive time to get ready again.
AMIBIOS checks for a <Del> key press and runs
AMIBIOS Setup if the key has been pressed.

Enabled

AMIBIOS does not test system memory above 1 MB.

AMIBIOS does not wait for up to 40 seconds for a
READY signal from the IDE hard disk drive. If a
READY signal is not received immediately from the
IDE drive, AMIBIOS does not configure that drive.
AMIBIOS does not wait for .5 seconds after sending
a RESET signal to the IDE drive to allow the IDE
drive time to get ready again. In

Enabled,

the

keyboard will be bypassed.

Note: You cannot run AMIBIOS Setup at system boot, because there is
no delay allowing you to hit <Del> to begin the Setup routine

.

Pri Master ARMD Emulated as
Pri Slave ARMD Emulated as
Sec Master ARMD Emulated as
Sec Slave ARMD Emulated as

Options for Pri Master ARMD Emulated as, Pri Slave ARMD Emulated as,
Sec Master ARMD Emulated as and Sec Slave ARMD Emulated as are

Auto, Floppy or Hard disk

.

1st Boot Device
2nd Boot Device
3rd Boot Device

The options for the 1st Boot Device are

Disabled, 1st IDE-HDD, 2nd IDE-

BIOS User's Manual

5-4

HDD, 3rd IDE-HDD, 4th IDE-HDD, Floppy, ARMD-FDD, ARMD-HDD, ATAPI
CD ROM, SCSI, Network

or

I20

. The options for the 2nd Boot Device are

Disabled, 1st IDE-HDD, 2nd IDE-HDD, 3rd IDE-HDD, 4th IDE-HDD, Floppy,
ARMD-FDD, ARMD-HDD or ATAPI CD ROM

. The options for the 3rd Boot

Device are

Disabled, 1st IDE-HDD, 2nd IDE-HDD, 3rd IDE-HDD, 4th IDE-

HDD, Floppy, ARMD-FDD, ARMD-HDD or ATAPI CD ROM

.

1st IDE-HDD, 2nd IDE-HDD, 3rd IDE-HDD and 4th IDE-HDD are the four hard
disks that can be installed by the BIOS. 1st IDE-HDD is the first hard disk
installed by the BIOS, 2nd IDE-HDD is the second hard disk, and so on. For
example, if the system has a hard disk connected to Primary Slave and
another hard disk to Secondary Master, then 1st IDE-HDD will be referred to
as the hard disk connected to Primary Slave and 2nd IDE-HDD will be
referred to as the hard disk connected to the Secondary Master. 3rd IDE­HDD and 4th IDE-HDD are not present. Note that the order of the initializa­tion of the devices connected to the primary and secondary channels are
Primary Master first, Primary Slave second, Secondary Master third, and
Secondary Slave fourth.

The BIOS will attempt to read the boot record from 1st, 2nd, 3rd and 4th boot
device in the selected order until it is successful in reading the booting
record. The BIOS will not attempt to boot from any device which is not
selected as the boot device.

Try Other Boot Device

This option controls the action of the BIOS if all the selected boot devices
failed to boot. The settings for this option are

Yes

or No. If

Yes

is selected
and all the selected boot devices failed to boot, the BIOS will try to boot from
the other boot devices (in a predefined sequence) which are present but not
selected as boot devices in the setup (and hence not yet been tried for
booting). If selected as No and all selected boot devices failed to boot, the
BIOS will try not to boot from the other boot devices which may be present
but not selected as boot devices in setup.

Initial Display Mode

This option determines the display screen with which the POST is going to
start the display. The settings for this option are

BIOS

or

Silent

. If selected

as

BIOS,

the POST will start with the normal sign-on message screen. If

Silent

is selected, the POST will start with the silent screen.

Display Mode at Add-on ROM Init

This option determines the display mode during add-on ROM (except Video
add-on ROM) initialization. The settings for this option are

Force BIOS

or

Chapter 5: Running Setup

5-5

Keep Current

. If selected as

Force BIOS,

the POST will force the display to

be changed to BIOS mode before giving control to any add-on ROM. If no
add-on ROM is found, then the current display mode will remain unchanged
even if this setup question is selected as

Force BIOS.

If selected as

Keep

Current,

then the current display mode will remain unchanged.

Floppy Access Control

The settings for this option are

Read-Write

or

Read-Only

.

Hard Disk Access Control

The settings for this option are

Read-Write

or

Read-Only

.

S.M.A.R.T. for Hard Disks

S.M.A.R.T. (Self-Monitoring, Analysis and Reporting Technology) is a
technology developed to manage the reliability of the hard disk by predicting
future device failures. The hard disk needs to be S.M.A.R.T. capable. The
settings for this option are

Disabled

or

Enabled

. *

Note: S.M.A.R.T. cannot
predict all future device failures. S.M.A.R.T. should be used as a
warning tool, not as a tool to predict the device reliability

.

Boot Up Num-Lock

Settings for this option are

On

or

Off

. When this option is set to On, the
BIOS turns off the Num Lock key when the system is powered on. This will
enable the end user to use the arrow keys on both the numeric keypad and
the keyboard.

PS/2 Mouse Support

Settings for this option are

Enabled

or

Disabled

. When this option is set to

Enabled

, AMIBIOS supports a PS/2-type mouse.

Primary Display

This option specifies the type of display adapter card installed in the system.
The settings are

Absent, VGA/EGA, CGA40x25, CGA80x25

or

Mono

.

Password Check

This option enables the password check option every time the system boots
or the end user runs WinBIOS Setup. If

Always

is chosen, a user password

prompt appears every time the computer is turned on. If

Setup

is chosen,

the password prompt appears if WinBIOS Setup is executed.

Boot to OS/2

If DRAM size is over 64 MB, set this option to

Yes

to permit AMIBIOS to run

with IBM OS/2. The settings are No or

Yes

.

BIOS User's Manual

5-6

CPU Microcode Updation

Set this option to

Enabled

to permit the CPU to be updated on line. The

settings for this option are

Enabled

or

Disabled

.

Internal Cache

This option is for enabling or disabling the internal cache memory. The
settings for this option are

Disabled, Write-thru

or

WriteBack

.

System BIOS Cacheable

When set to

Enabled

, the contents of the F0000h system memory segment
can be read from or written to cache memory. The contents of this memory
segment are always copied from the BIOS ROM to system RAM for faster
execution. The settings are

Enabled

or

Disabled

.

Note: The Optimal
default setting is Enabled and the Fail-Safe default setting is Disabled.
Set this option to Enabled to permit the contents of F0000h RAM
memory segment to be written to and read from cache memory.

CPU ECC

The settings for this option are

Enabled

or

Disabled

. This option enables

Pentium II L2 cache ECC function.

MPS Revision 1.4

The settings for this option are

1.1

or

1.4.

C000, 16K Shadow
C400, 16K Shadow

These options specify how the 32 KB of video ROM at C0000h is treated.
The settings are:

Disabled, Enabled or Cached

. When set to

Disabled,

the

contents of the video ROM are not copied to RAM. When set to

Enabled,

the contents of the video ROM area from C0000h-C7FFFh are copied
(shadowed) from ROM to RAM for faster execution. When set to

Cached

,
the contents of the video ROM area from C0000h-C7FFFh are copied from
ROM to RAM, and can be written to or read from cache memory.

C000, 16K Shadow
C400, 16K Shadow
D800, 16K Shadow
CC00, 16K Shadow
D400, 16K Shadow
D800, 16K Shadow
DC00, 16K Shadow

These options enable shadowing of the contents of the ROM area named in
the option. The ROM area not used by ISA adapter cards is allocated to PCI

Chapter 5: Running Setup

5-7

adapter cards. The settings are:

Disabled, Enabled or Cached

. When set

to

Disabled,

the contents of the video ROM are not copied to RAM. When

set to

Enabled,

the contents of the video ROM area from C0000h-C7FFFh are

copied (shadowed) from ROM to RAM for faster execution. When set to

Cached,

the contents of the video ROM area from C0000h-C7FFFh are copied

from ROM to RAM and can be written to or read from cache memory.

5-1-3 Advanced Chipset Setup

USB Function

The settings for this option are

Enabled

or

Disabled

. Set this option to

Enabled

to enable the USB (Universal Serial Bus) functions.

USB KB/Mouse Legacy Support

The settings for this option are

Keyboard, Auto, Keyboard+Mouse

or

Dis-

abled

. Set this option to

Enabled

to enable the USB keyboard and mouse.

Port 64/60 Emulation

The settings for this option are

Enabled

or

Disabled

.

SERR# (System Error)

The settings for this option are

Enabled

or

Disabled

. Set to

Enabled

to
enable the SERR# signal on the bus. GX asserts this signal to indicate a
system error condition. SERR# is asserted under the following conditions:

- In an ECC configuration, the GX asserts SERR#, for single bit (correctable) ECC errors or
multiple bit (non-correctable) ECC errors if SERR# signaling is enabled via the ERRCMD
control register. Any ECC errors received during initialization should be ignored.

- The GX asserts SERR# for one clock when it detects a target abort during GX initiated PCI
cycle

- The GX can also assert SERR# when a PCI parity error occurs during the address or data
phase

- The GX can assert SERR# when it detects a PCI address or data parity error on AGP

- The GX can assert SERR# upon detection of access to an invalid entry in the Graphics
Aperature Translation Table

- The GX can assert SERR# upon detecting an invalid AGP master access outside of AGP
aperture and outside of main DRAM range (i.e. in the 640k - 1M range or above TOM)

- The GX can assert SERR# upon detecting an invalid AGP master access outside of AGP
aperture.

- The GX asserts SERR# for one clock when it detects a target abort during GX initiated AGP
cycle

BIOS User's Manual

5-8

PERR#

The settings for this option are

Enabled

or

Disabled

. Set to

Enabled

to

enable the PERR# signal on the bus.

WSC# Handshake (Write Snoop Complete)

This signal is asserted active to indicate that all the snoop activity on the
CPU bus on the behalf of the last PCI-DRAM write transaction is complete
and that it is safe to send the APIC interrupt message. The settings for this
option are

Enabled

or

Disabled

. Set to

Enabled

to enable handshaking for

the WSC# signal.

USWC Write Post

The settings for this option are

Enabled

or

Disabled

. This option sets the
status of USWC (Uncacheable, Speculatable, Write-Combined) posted writes.
Set to

Enabled

to enable USWC posted writes to I/O. Set to

Disabled

to

disable USWC posted writes to I/O.

GX Master Latency Timer (CLKs)

This option specifies the master latency timings (in PCI clocks) for devices in
the computer. The settings are

Disabled, 32, 64, 96, 128, 160, 192

or

224

.

Multi-Trans Timer (Clks)

This option specifies the multi-trans latency timings (in PCI clocks) for
devices in the computer. The settings are

Disabled, 32, 64, 96, 128, 160

,

192

or

224

.

PCI1 to PCI0 Access

The settings for this option are

Enabled

or

Disabled

. Set to

Enabled

to

enable access between two different PCI buses (PCI1 and PCI0).

Memory Autosizing Support

The dynamic detection and sizing of SDRAM and EDO is performed by the
BIOS in a system populated with memory which has no SPD information.
When set to

Enable

, memory does not have the SPD information. The

settings for this option are

Auto

or

Enable

.

DRAM Integrity Mode

The settings for this option are

None, EC

or

ECC Hardware

.

Note: For ECC
memory only. See the table below to set the type of system memory
checking.

Chapter 5: Running Setup

5-9

Setting Description

None No error checking or error reporting is done.

EC Multibit errors are detected and reported as parity

errors. Single-bit errors are corrected by the
chipset. Corrected bits of data from memory are not
written back to DRAM system memory.

ECC Multibit errors are detected and reported as parity
Hardware errors. Single-bit errors are corrected by the

chipset and are written back to DRAM system
memory. If a soft (correctable) error occurs, writing
the fixed data back to DRAM system memory will
resolve the problem. Most DRAM errors are soft
errors. If a hard (uncorrectable) error occurs, writing
the fixed data back to DRAM system memory does
not solve the problem. In this case, the second time
the error occurs in the same location, a Parity Error
is reported, indicating an uncorrectable error. If ECC
is selected, AMIBIOS automatically enables the
System Management Interface (SMI). If you do not
want to enable power management, set the Power
Management/APM option to

Disabled

and set all

Power Management Setup timeout options to

Disabled

. To enable power management, set Power

Management/APM to

Enabled

and set the power

management timeout options as desired.

DRAM Refresh Rate

This option specifies the interval between Refresh signals to DRAM system
memory. The settings for this option are

15.6 us

(micro-seconds),

31.2 us

,

62.4 us, 124.8 us

or

249.6 us

.

Memory Hole

This option specifies the location of an area of memory that cannot be
addressed on the ISA bus. The settings are

Disabled, 15 MB-16 MB

, or

512

KB-640 KB

.

SDRAM CAS# Latency

This option regulates the column address strobe. The settings are 2 SCLKs,
3 SCLKs or

Auto

.

BIOS User's Manual

5-10

SDRAM RAS# to CAS# Delay

This option specifies the length of the delay inserted between the RAS and
CAS signals of the DRAM system memory access cycle if SDRAM is
installed. The settings are

Auto

(AMIBIOS automatically determines the

optimal delay),

2 SCLKs

or

3 SCLKs

.

Note: The Optimal default setting is

Auto and the Fail-Safe default setting is 3 SCLKs

.

SDRAM RAS# Precharge

This option specifies the length of the RAS precharge part of the DRAM
system memory access cycle when Synchronous DRAM system memory is
installed in the computer. The settings are

Auto

(AMIBIOS automatically

determines the optimal delay),

2 SCLKs or 3 SCLKs

.

Note: The Optimal

default setting is Auto and the Fail-Safe default setting is 3 SCLKs.

Power Down SDRAM

BX supports SDRAM power down mode to minimize SDRAM power usage.
The settings for this option are

Enabled

or

Disabled

. The

Enabled

setting

enables the SDRAM Power Down feature.

ACPI Control Register

The settings for this option are

Enabled

or

Disabled

. Set this option to

Enabled

to enable the ACPI (Advanced Configuration and Power Interface)

control register.

Gated Clock

Signal GCLKEN enables internal dynamic clock gating in the GX when a
AGPset "IDLE" state occurs. This happens when the GX detects an idle
state on all its buses. The settings for this option are

Enabled

or

Disabled

.

The

Enabled

setting enables the gated clock.

Graphics Aperture Size

This option specifies the amount of system memory that can be used by the
Accelerated Graphics Port (AGP). The settings are

4 MB, 8 MB, 16 MB, 32

MB, 64 MB, 128 MB

, or

256 MB

.

Search for MDA (Monochrome Adapter) Range (B0000h-B7FFFh)
Resources

Legacy support requires the ability to have a second graphics controller
(monochrome) in the system. In an AGP system, accesses in the normal
VGA range are forwarded to the AGP bus. Since the monochrome adapter
may be on the PCI (or ISA) bus, the GX must decode cycles in the MDA
range and forward them to PCI. The settings for this option are

Yes

or No.

Set this option to

Yes

to let AMIBIOS search for MDA resources.

Chapter 5: Running Setup

5-11

AGP Multi-Trans Timer (AGP Clks)

This option sets the AGP multi-trans timer. The settings are in units of AGP
clocks: 32, 64, 96,

128, 160, 192

, or

224

.

AGP Low-Priority Timer

This option controls the minimum tenure on the AGP for low priority data
transaction for both read and write. The settings are

Disabled, 16, 32, 64,

96, 128, 160, 192 or 224

.

AGP SERR (Advanced Graphic Port System Error)

GX asserts this signal to indicate a AGP system error condition. The
settings for this option are

Enabled

or

Disabled

. Set to

Enabled

to enable

the AGP SERR# signal.

AGP Parity Error Response

The settings for this option are

Enabled

or

Disabled

. Set to

Enabled

to

enable the AGP (Accelerated Graphics Port) to respond to parity errors.

8bit I/O Recovery Time

This option specifies the length of a delay inserted between consecutive 8-bit
I/O operations. The settings are

Disabled, 8 SYSCLKs, 1 SYSCLK, 2

SYSCLKs, 3 SYSCLKs, 4 SYSCLKs, 5 SYSCLKs

or

6 SYSCLKs

.

16bit I/O Recovery Time

This option specifies the length of a delay inserted between consecutive 16­bit I/O operations. The settings are

Disabled, 3 SYSCLK, 1 SYSCLKs, 2

SYSCLKs

or

4 SYSCLKs

.

PIIX4 SERR#

This signal is asserted to indicate a PIIX4 System Error condition. The
settings for this option are

Enabled

or

Disabled

. The

Enabled

option enables

the SERR# signal for the Intel PIIX4 chip.

USB Passive Release

GX releases USB bus when it is idle to maximize the USB bus usage. The
settings for this option are

Enabled

or

Disabled

. Set this option to

Enabled

to enable passive release for USB.

PIIX4 Passive Release

This option functions similarly to USB Passive Release. The settings for this
option are

Enabled

or

Disabled

. Set to

Enabled

to enable passive release

for the Intel PIIX4 chip.

BIOS User's Manual

5-12

PIIX4 Delayed Transaction

GX is capable of PIIX4 transaction to improve PIIX4 interrupt efficiency. The
settings for this option are

Enabled

or

Disabled

. Set this option to

Enabled

to enable delayed transactions for the Intel PIIX4 chip.

Type F DMA Buffer Control1
Type F DMA Buffer Control2

These options specify the DMA channel where Type F buffer control is
implemented. The settings are

Disabled, Channel 1-0, Channel 1-1, Channel

1-2, Channel 1-3, Channel 1-4, Channel 1-5, Channel 1-6

or

Channel 1-7

.

DMA0 Type
DMA1 Type
DMA2 Type
DMA3 Type
DMA4 Type
DMA5 Type
DMA6 Type
DMA7 Type

These options specify the bus that the specified DMA channel can be used
on. The settings are

PC/PCI, Distributed

, or

Normal ISA

.

Memory Buffer Strength

The settings for this option are

Strong, Medium

or

Auto

.

Manufacturer's Setting

Note: The user should always set this option to mode 0. All other
modes are for factory testing only

.

5-1-4 Power Management Setup

Power Management/APM

The settings for this feature are:

APM, ACPI or Disabled

. Set to

APM

to
enable the power conservation feature specified by Intel and Microsoft INT 15h
Advance Power Management BIOS functions. Set to

ACPI

if your operating
system supports Microsoft's Advanced Configuration and Power Interface
(ACPI) standard.

Power Button Function

This option specifies how the power button mounted externally on the
computer chassis is used. The settings are:

Suspend

or

On/Off

. When set

Chapter 5: Running Setup

5-13

to

On/Off

, pushing the power button turns the computer on or off. When set

to

Suspend

, pushing the power button places the computer in Suspend mode

or Full On power mode.

Green PC Monitor Power State

This option specifies the power state that the green PC-compliant video
monitor enters when AMIBIOS places it in a power savings state after the
specified period of display inactivity has expired. The settings are

Standby

,

Suspend

or

Off. Note: The Optimal default setting for this option is

Suspend and the Fail-Safe setting is Standby

.

Video Power Down Mode

This option specifies the power conserving state that the VGA video sub­system enters after the specified period of display inactivity has expired. The
settings are

Disabled, Standby

, or

Suspend

.

Note: The Optimal default
setting for this option is Suspend and the Fail-Safe default setting is
Disabled

.

Hard Disk Power Down Mode

This option specifies the power conserving state that the hard disk drive
enters after the specified period of hard drive inactivity has expired. The
settings are

Disabled, Standby

, or

Suspend

.

Note: The Optimal default
setting for this option is Suspend and the Fail-Safe default setting is
Disabled

.

Hard Disk Timeout (Minutes)

This option specifies the length of a period of hard disk drive inactivity. When
this length of time expires, the computer enters power-conserving state
specified in the Hard Disk Power Down Mode option. The settings are

Disabled

and

1 Min through 15 Min in 1 minute intervals

.

Power Saving Type

The settings for this option are

Sleep, Stop Clock or Deep Sleep

.

Standby/Suspend Timer Unit

This allows you to set the standby timeout and suspend timeout timer unit.
The settings are

32 secs, 4 msecs, 4 min

or

4 secs.

Standby Timeout

This option specifies the length of a period of system inactivity while in full
power on state. When this length of time expires, the computer enters
standby power state. The settings are

Disabled

and

4 Min through 508 Min

in 4 minute intervals

.

BIOS User's Manual

5-14

Suspend Timeout (Minutes)

This option specifies the length of a period of system inactivity while in
standby state. When this length of time expires, the computer enters
suspend power state. The settings are

Disabled

and

4 Min through 508 Min

in 4 minute intervals

.

Slow Clock Ratio

The value of the slow clock ratio indicates the percentage of time the
STPCLK# signal is asserted while in the thermal throttle mode. The settings
are

Disabled, 0-12.5%

, 12.5-

25%

, 25-37.5%, 37.

5-50%, 50-62.5%, 62.5-75%

,

or

75-87.5%

.

Display Activity

This option specifies if AMIBIOS is to monitor display activity for power
conservation purposes. When this option is set to

Monitor

and there is no
display activity for the length of time specified in the Standby Timeout
(Minute) option, the computer enters a power savings state. The settings are

Monitor

or

Ignore

.

Device 6 (Serial port 1)
Device 7 (Serial port 2)
Device 8 (Parallel port)
Device 5 (Floppy disk)
Device 0 (Primary Master IDE)
Device 1 (Primary Slave IDE)
Device 2 (Secondary Master IDE)
Device 3 (Secondary Slave IDE)

When set to

Monitor

, these options enable event monitoring on the specified
hardware interrupt request line. If set to Monitor and the computer is in a
power saving state, AMIBIOS watches for activity on the specifies IRQ line.
The computer enters the Full On state if any activity occurs. AMIBIOS
reloads the Standby and Suspend timeout timers if activity occurs on the
specified IRQ line.

Note: The Optimal default setting for each option is
Ignore with the exception of Devices 0 (Primary Master IDE) and 6 (Serial
Port 1) which should be set to Monitor. The Fail-Safe default for each
option is Monitor.

LAN Wake-Up
RTC Wake-UP

Options for LAN Wake-Up and RTC Wake-Up are

Disabled

or

Enabled

.

When enabled, the Hour and Minute functions become available.

Chapter 5: Running Setup

5-15

5-1-5 PCI/PnP Setup

Plug and Play-Aware OS

The settings for this option are No or

Yes

. Set this option to

Yes

if the
operating system in the computer is aware of and follows the Plug and Play
specification. AMIBIOS only detects and enables PnP ISA adapter cards
that are required for system boot. Currently, only Windows 95 is PnP-Aware.
Set this option to

No

if the operating system (such as DOS, OS/2, Windows

3.x) does not use PnP. You must set this option correctly. Otherwise, PnP­aware adapter cards installed in the computer will not be configured properly.

PCI Latency Timer (PCI Clocks)

This option specifies the latency timings in PCI clocks for all PCI devices.
The settings are 32, 64, 96,

128, 160, 192, 224

, or

248

.

PCI VGA Palette Snoop

The settings for this option are

Disabled or Enabled.

When set to

Enabled,

multiple VGA devices operating on different buses can handle data from the
CPU on each set of palette registers on every video device. Bit 5 of the
command register in the PCI device configuration space is the VGA Palette
Snoop bit (0 is disabled). For example: if there are two VGA devices in the
computer (one PCI and one ISA) and this option is disabled, data read and
written by the CPU is only directed to the PCI VGA device's palette registers.
If enabled, data read and written by the CPU is directed to both the PCI VGA
device's palette registers and the ISA VGA palette registers. This will permit
the palette registers of both devices to be identical. This option must be set
to

Enabled

if any ISA adapter card installed in the system requires VGA

palette snooping.

PCI IDE Busmaster

The settings for this option are

Disabled

or

Enabled

. Set to

Enabled

to
specify the IDE Controller on the PCI bus has bus mastering capabilities.
Under Windows 95, you should set this option to

Disabled

and install the

Bus Mastering driver.

Offboard PCI IDE Card

This option specifies if an offboard PCI IDE controller adapter card is installed
in the computer. The PCI expansion slot on the motherboard where the
offboard PCI IDE controller is installed must be specified. If an offboard PCI
IDE controller is used, the onboard IDE controller is automatically disabled.
The settings are

Auto

(AMIBIOS automatically determines where the offboard

PCI IDE controller adapter card is installed),

Slot 1, Slot 2, Slot 3, Slot 4,

Slot 5

or

Slot 6

.

BIOS User's Manual

5-16

This option forces IRQ14 and IRQ15 to a PCI slot on the PCI local bus. This
is necessary to support non-compliant ISA IDE controller adapter cards. If an
offboard PCI IDE controller adapter card is installed in the computer, you
must also set the Offboard PCI IDE Primary IRQ and Offboard PCI IDE
Secondary IRQ options.

Offboard PCI IDE Primary IRQ
Offboard PCI IDE Secondary IRQ

These options specify the PCI interrupt used by the primary (or secondary)
IDE channel on the offboard PCI IDE controller. The settings are

Disabled

,

Hardwired, INTA, INTB, INTC

, or

INTD

.

PCI Slot1 IRQ Priority
PCI Slot2 IRQ Priority
PCI Slot3 IRQ Priority
PCI Slot4 IRQ Priority

These options specify the IRQ priority for PCI devices installed in the PCI
expansion slots. The settings are

Auto, (IRQ) 3, 4, 5, 7, 9, 10, 11, 12 or 14

in priority order

.

DMA Channel 0
DMA Channel 1
DMA Channel 3
DMA Channel 5
DMA Channel 6
DMA Channel 7

These DMA channels control the data transfers between the I/O devices and
the system memory. The chipset allows the BIOS to choose which channels
to do the job. The settings are

PnP or ISA/EISA.

IRQ3
IRQ4
IRQ5
IRQ7
IRQ9
IRQ10
IRQ11
IRQ12
IRQ14
IRQ15

These options specify which bus the specified IRQ line is used on and allow
you to reserve IRQs for legacy ISA adapter cards. If more IRQs must be

Chapter 5: Running Setup

5-17

removed from the pool, the end user can use these options to reserve the
IRQ by assigning an

ISA/EISA

setting to it. Onboard I/O is configured by

AMIBIOS. All IRQs used by onboard I/O are configured as PCI/PnP.

IRQ14 and 15 will not be available if the onboard PCI IDE is enabled. If all
IRQs are set to

ISA/EISA

and IRQ14 and 15 are allocated to the onboard PCI
IDE, IRQ 9 will still be available for PCI and PnP devices. This is because at
least one IRQ must be available for PCI and PnP devices. The settings are

PCI/PnP or ISA/EISA.

Reserved Memory Size

This option specifies the size of the memory area reserved for legacy ISA
adapter cards. The settings are

Disabled, 16K, 32K

or

64K

.

Reserved Memory Address

This option specifies the beginning address (in hex) of the reserved memory
area. The specified ROM memory area is reserved for use by legacy ISA
adapter cards. The settings are

C0000, C4000, C8000, CC000, D0000

,

D4000, D8000

or

DC000

.

PCI Device Search Order

The settings for this option are

First-Last

or

Last-First

.

Default Primary Video

This feature supports multiple displays. The settings are

AGP

or

PCI

.

5-1-6 Peripheral Setup

On-board SCSI

The settings for this option are

Enabled

or

Disabled

. When set to

Enable

this option enables the Adaptec 7895 BIOS on the P6DGS motherboard or
the Adaptec 7890 on the P6DGU/P6SGU motherboards.

Remote Power On

Microsoft's Memphis OS supports this feature which can wake-up the system
from SoftOff state through devices (such as an external modem) that are
connected to COM1 or COM2. The settings are

Disabled

or

Enabled

.

System Current Temperature

The current system temperature is displayed in this option.

BIOS User's Manual

5-18

System Overheat Warning

The settings for this option are

Enabled

or

Disabled.

When set to

Enabled,

this option allows the user to set an overheat warning temperature.

Set Overheat Warning Temperature

Use this option to set the overheat warning temperature. The settings are

25°C through 99°C in 1°C intervals

.

Note: The Optimal and Fail-Safe

default settings are 63°C

.

H/W Monitor In0 (CPU 1)
H/W Monitor In1 (CPU 2)
H/W Monitor In2 (+3.3V)
H/W Monitor In3 (+5V)
H/W Monitor In4 (+12V)
H/W Monitor In5 (-12V)
H/W Monitor In6 (-5V)
CPU1 Fan
CPU2 Fan
Thermal Control Fan

The above features are for PC Health Monitoring. The motherboards with
W83781D have seven on-board voltage monitors for the CPU core, CPU I/O,
+3.3V, +5V, -5V, +12V, and -12V, and three fan status monitors.

On-Board FDC

This option enables the FDC (Floppy Drive Controller) on the motherboard.
The settings are

Disabled

, or

Enabled

.

On-Board Serial Port A

This option specifies the base I/O port address of serial port 1. The settings
are

Auto

(AMIBIOS automatically determines the correct base I/O port

address),

Disabled, 3F8h/

COM1,

2F8h/COM2, 3E8h/COM3

or

2E8h/COM4

.

On-Board Serial Port B

This option specifies the base I/O port address of serial port 2. The settings
are

Auto

(AMIBIOS automatically determines the correct base I/O port

address),

Disabled, 3F8h/COM1, 2F8h/COM2, 3E8h/COM3

or

2E8h/COM4

.

Serial Port B Mode

The settings for this option are

Normal, IrDA

or

ASK IR

. When set to

IrDA,

the IR Duplex Mode becomes available and can be set to either Half or Full.
When set to

ASK IR,

the IrDA Protocol becomes available and can be set to

1.6 us or 3/16.

Chapter 5: Running Setup

5-19

On-Board Parallel Port

This option specifies the base I/O port address of the parallel port on the
motherboard. The settings are

Auto

(AMIBIOS automatically determines the

correct base I/O port address),

Disabled, 378, 278

or

3BC

.

Parallel Port Mode

This option specifies the parallel port mode. The settings are

Normal, Bi-Dir

,

EPP

or

ECP

. When set to

Normal,

the normal parallel port mode is used.

Use

Bi-Dir

to support bidirectional transfers. Use

EPP

(Enhanced Parallel
Port) to provide asymmetric bidirectional data transfer driven by the host
device. Use

ECP

(Extended Capabilities Port) to achieve data transfer rates
of up to 2.5 Mbps. ECP uses the DMA protocol and provides symmetric
bidirectional communication.

Note: The Optimal default setting for this

option is Bi-Dir and the Fail-Safe setting is Normal

.

EPP Version

The settings are 1.7 or 1.9.

Note: The Optimal and Fail-Safe default

settings are N/A.

Parallel Port IRQ

This option specifies the IRQ to be used by the parallel port. The settings
are 5 or 7.

Parallel Port DMA Channel

This option is only available if the setting of the parallel port mode option is

ECP

. The settings are 0, 1, 2, 3, 5, 6 or 7.

Note: This option is N/A

.

On-Board IDE

This option specifies the onboard IDE controller channels to be used. The
settings are

Disabled, Primary, Secondary

or

Both

.

5-2 Auto Detect Hard Disks

Date and Time Configuration

The current values for each category are displayed. Enter new values through
the keyboard.

Floppy A
Floppy B

Choose the Floppy Drive A or B icon to specify the floppy drive type. The
setting for Floppy Drive A is

1.44 MB 3 1/2 inch

and for Floppy Drive B is

Not Installed

.

BIOS User's Manual

5-20

Pri Master
Pri Slave
Sec Master
Sec Slave

Select these options to configure the drive named in the option. The setting
for Primary Master and Secondary Slave is

Auto

. The Primary Slave and

Secondary Master are

Not-Installed

.

5-3 Change User Password

Change Supervisor Password

The system can be configured so that all users must enter a password every
time the system boots or when the AMIBIOS Hiflex setup is executed. You
can set either a Supervisor password or a User password. If you do not want
to use a password, just press <Enter> when the password prompt appears.

The password check option is enabled in the Advanced Setup by choosing
either

Always

or

Setup

. The password is stored in CMOS RAM. You can
enter a password by typing the password on the keyboard, selecting each
letter via the mouse, or selecting each letter via the pen stylus. Pen access
must be customized for each specific hardware platform.

When you select Supervisor or User, AMIBIOS prompts for a password. You
must set the Supervisor password before you can set the User password.
Enter a 1-6 character password. The password does not appear on the
screen when typed. Retype the new password as prompted and press
<Enter>. Make sure you write it down. If you forget it, you must drain
CMOS RAM and reconfigure.

5-4 Change Language Setting

Note: The Optimal and Fail-Safe default settings for this option are
English.

Chapter 5: Running Setup

5-21

5-5 Default Settings

Every option in AMIBIOS Hiflex Setup contains two default settings: a Fail­Safe default, and an Optimal default.

5-5-1 Auto Configuration with Optimal Settings

The Optimal default settings provide optimum performance settings for all
devices and system features.

5-5-2 Auto Configuration with Fail-Safe Settings

The Fail-Safe default settings consist of the safest set of parameters. Use
them if the system is behaving erratically. They should always work but do
not provide optimal system performance characteristics.

BIOS User's Manual

5-22

Notes

Appendix A

BIOS Error Beep Codes & Messages

During the POST (Power-On Self-Test) routines, which are performed each
time the system is powered on, errors may occur.

Non-fatal errors are those which, in most cases, allow the system to
continue the boot-up process. The error messages normally appear on the
screen.

Fatal errors are those which will not allow the system to continue the boot­up procedure. If a fatal error occurs, you should consult with your system
manufacturer for possible repairs.

These fatal errors are usually communicated through a series of audible
beeps. On the following page, the numbers on the fatal error list correspond
to the number of beeps for the corresponding error. All errors listed, with the
exception of #8, are fatal errors.

Appendix A: BIOS Error Beep Codes

BIOS User’s Manual

A-2

Beeps Error message Description

1 Refresh Failure The memory refresh circuitry on the

motherboard is faulty.

2 Parity Error A parity error was detected in the base

memory (the first 64 KB block) of the
system.

3 Base 64 KB Memory Failure A memory failure occurred within the

first 64 KB of memory.

4 Timer Not Operational A memory failure was detected in the

first 64 KB of memory, or Timer 1 is
not functioning.

5 Processor Error The CPU on the system board

generated an error.

6 8042 - Gate A20 Failure The keyboard controller (8042) contains

the Gate A20 switch which allows the
CPU to operate in virtual mode. This
error means that the BIOS cannot
switch the CPU into protected mode.

7 Processor Exception The CPU on the motherboard generated

Interrupt Error an exception interrupt.

8 Display Memory Read/Write The system video adapter is either

Error missing or its memory is faulty.

Please Note:

This is not a fatal error.

9 ROM Checksum Error The ROM checksum value does not

match the value encoded in the BIOS.

10 CMOS Shutdown Register The shutdown register for CMOS

Read/Write Error memory has failed.

Refer to the table on page A-3 for solutions to the error beep codes.

A-3

Appendix A: BIOS Error Beep Codes

If it beeps... then ...

1, 2 or 3 times reseat the DIMM memory. If the

system still beeps, replace the memory.

6 times reseat the keyboard controller chip. If it

still beeps, replace the keyboard
controller. If it still beeps, try a
different keyboard, or replace
the keyboard fuse, if the keyboard has one.

8 times there is a memory error on the

video adapter. Replace the video
adapter or the RAM on the video
adapter.

9 times the BIOS ROM chip is bad.

The system probably needs a
new BIOS ROM chip.

4, 5, 7 the motherboard must be replaced.
or 10 times

BIOS User’s Manual

A-4

Error Message Information

8042 Gate -- A20 Gate A20 on the keyboard controller (8042)
Error is not working. Replace the 8042.

Address Line Short! Error in the address decoding circuitry on

the motherboard.

C: Drive Error Hard disk drive C: does not respond. Run

the Hard Disk Utility to correct this problem.
Also, check the C: hard disk type in Standard
Setup to make sure that the hard disk type is
correct.

C: Drive Failure Hard disk drive C: does not respond.

Replace the hard disk drive.

Cache Memory Bad Cache memory is defective. Replace it. Do

Not Enable Cache!

CH-2 Timer Error Most ISA computers include two times.

There is an error in time 2.

CMOS Battery State Low CMOS RAM is powered by a battery. The

battery power is low. Replace the battery.

CMOS Checksum Failure After CMOS RAM values are saved, a

checksum value is generated for error
checking. The previous value is different from
the current value. Run WINBIOS Setup or
AMIBIOS Setup.

CMOS System Option The values stored in CMOS RAM are either
Not Set corrupt or nonexistent. Run WINBIOS

Setup or AMIBIOS Setup.

CMOS Display Type The video type in CMOS RAM does not
Mismatch match the type detected by the BIOS. Run

WINBIOS Setup or AMIBIOS Setup.

CMOS Memory Size The amount of memory on the motherboard is
Mismatch different than the amount in CMOS RAM.

Run WINBIOS Setup or AMIBIOS
Setup.

A-5

Appendix A: BIOS Error Beep Codes

Error Message Information

CMOS Time and Run Standard Setup to set the date and time
Date Not Set in CMOS RAM.

D: Drive Error Hard disk drive D: does not respond. Run

the Hard Disk Utility. Also check the D: hard
disk type in Standard Setup to make sure that
the hard disk drive type is correct.

D: Drive Failure Hard disk drive D: does not respond.

Replace the hard disk.

Diskette Boot Failure The boot disk in floppy drive A: is corrupt. It

cannot be used to boot the computer. Use
another boot disk and follow the on-screen
instructions.

Display Switch Some computers require a video switch on
Not Proper the motherboard be set to either color or

monochrome. Turn the computer off, set the
switch, then power on.

DMA Error Error in the DMA controller.

DMA #1 Error Error in the first DMA channel.

DMA #2 Error Error in the second DMA channel.

FDD Controller Failure The BIOS cannot communicate with the

floppy disk drive controller. Check all
appropriate connections after the computer is
powered down.

HDD Controller Failure The BIOS cannot communicate with the hard

disk drive controller. Check all appropriate
connections after the computer is powered
down.

INTR #1 Error Interrupt channel 1 failed POST.

INTR #2 Error Interrupt channel 2 failed POST.

BIOS User’s Manual

A-6

Error Message Information

Invalid Boot Diskette The BIOS can read the disk in floppy drive

A:, but cannot boot the computer. Use
another boot disk.

Keyboard Is Locked... The keyboard lock on the computer is
Unlock It engaged. The computer must be unlocked to

continue.

Keyboard Error There is a timing problem with the keyboard.

Set the

Keyboard

options in Standard Setup

to

Not Installed

to skip the keyboard post

routines.

KB/Interface Error There is an error in the keyboard connector.

No ROM BASIC Cannot find a bootable sector on either disk

drive A: or hard disk drive C:. The BIOS
calls INT 18h, which generates this message.
Use a bootable disk.

Off Board Parity error in memory installed in an
Parity Error expansion slot. The format is:

OFF BOARD PARITY ERROR ADDR
(HEX) = (XXXX) XXXX is the hex
address where the error occurred. Run
AMIDiag to find and correct memory
problems.

On Board Parity error in motherboard memory. The
Parity Error format is:

ON BOARD PARITY ERROR ADDR
(HEX) = (XXXX) XXXX is the hex
address where the error occurred. Run
AMIDiag to find and correct memory
problems.

Parity Error???? Parity error in system memory at an unknown

address. Run AMIDiag to find and correct
memory problems.

B-1

Appendix B: AMIBIOS POST Diagnostics Error Messages

Appendix B

AMIBIOS POST Diagnostic Error Messages

This section describes the power-on self-tests (POST) port 80 codes for the AMI
BIOS.

Check
PointDescription

00 Code copying to specific areas is done. Passing control

to INT 19h boot loader next.

03 NMI is Disabled. Next, checking for a soft reset or a

power-on condition.

05 The BIOS stack has been built. Next, disabling cache

memory.

06 Uncompressing the post code unit next.

07 Next, initializing the CPU init and the CPU data area.

08 The CMOS checksum calculation is done next.

0B Next, performing any required initialization before

keyboard BAT command is issued.

0C The keyboard controller I/B is free. Next, issuing the

BAT command to the keyboard controller.

0E The keyboard controller BAT command result has been

verified. Next, performing any necessary initialization
after the keyboard controller BAT command test.

0F The initialization after the keyboard controller BAT

command test is done. The keyboard command byte is
written next.

BIOS User’s Manual

B-2

Check
PointDescription

10 The keyboard controller command byte is written.

Next, issuing the pin 23 and 24 blocking and unblocking
commands.

11 Next, checking if the <End or <Ins> keys were pressed

during power on. Initializing CMOS RAM if the
Initialize CMOS RAM in every boot AMIBIOS POST
option was set in AMIBCP or the <End> key was
pressed.

12 Next, disabling DMA controllers 1 and 2 and interrupt

controllers 1 and 2.

13 The video display has been disabled. Port B has been

initialized. Next, initializing the chipset.

14 The 8254 timer test will begin next.

19 The 8254 timer test is over. Starting the memory refresh

test next.

1A The memory refresh test line is toggling. Checking the

15 second on/off time next.

23 Reading the 8042 input port and disabling the

MEGAKEY Green PC feature next. Making the
BIOS code segment writable and performing any
necessary configuration before initializing the interrupt
vectors.

24 The configuration required before interrupt vector

initialization has completed. Interrupt vector initialization
is done. Clearing the password if the POST DIAG
switch is on.

25 Interrupt vector initialization is done. Clearing the

password if the POST DIAG Switch is on.

27 Any initialization before setting video mode will be

done next.

B-3

Appendix B: AMIBIOS POST Diagnostics Error Messages

Check
PointDescription

28 Initialization before setting the video mode is complete.

Configuring the monochrome mode and color mode
settings next.

2A Bus initialization system, static, output devices will be

done next, if present.

2B Passing control to the video ROM to perform any

required configuration before the video ROM test.

2C All necessary processing before passing control to the

video ROM is done. Looking for the video ROM next
and passing control to it.

2D The video ROM has returned control to BIOS POST.

Performing any required processing after the video
ROM had control.

2E Completed post-video ROM test processing. If the

EGA/VGA controller is not found, performing the
display memory read/write test next.

2F The EGA/VGA controller was not found. The display

memory read/write test is about to begin.

30 The display memory read/write test passed. Look for

retrace checking next.

31 The display memory read/write test or retrace checking

failed. Performing the alternate display memory
read/write test next.

32 The alternate display memory read/write test passed.

Looking for alternate display retrace checking next.

34 Video display checking is over. Setting the display

mode next.

37 The display mode is set. Displaying the power on

message next.

BIOS User’s Manual

B-4

Check
PointDescription

38 Initializing the bus input, IPL, and general devices next, if

present.

39 Displaying bus initialization error messages.

3A The new cursor position has been read and saved.

Displaying the Hit <DEL> message next.

40 Preparing the descriptor tables next.

42 The descriptor tables are prepared. Entering protected

mode for the memory test next.

43 Entered protected mode. Enabling interrupts for

diagnostics mode next.

44 Interrupts enabled if the diagnostics switch is on.

Initializing data to check memory wraparound at 0:0 next.

45 Data initialized. Checking for memory wraparound at

0:0 and finding the total system memory size next.

46 The memory wraparound test has completed. The

memory size calculation has been completed. Writing
patterns to test memory next.

47 The memory pattern has been written to extended

memory. Writing patterns to the base 640 KB memory
next.

48 Patterns written in base memory. Determining the

amount of memory below 1 MB next.

49 The amount of memory below 1 MB has been found

and verified. Determining the amount of memory above
1 MB memory next.

4B The amount of memory above 1 MB has been found

and verified. Checking for a soft reset and clearing the
memory below 1 MB for the soft reset next. If this is a
power on situation, going to checkpoint 4Eh next.

B-5

Appendix B: AMIBIOS POST Diagnostics Error Messages

Check
PointDescription

4C The memory below 1 MB has been cleared via a soft

reset. Clearing the memory above 1 MB next.

4D The memory above 1 MB has been cleared via a soft

reset. Saving the memory size next. Going to checkpoint
52h next.

4E The memory test started, but not as the result of a soft

reset. Displaying the first 64 KB memory size next.

4F The memory size display has started. The display is

updated during the memory test. Performing the
sequential and random memory test next.

50 The memory below 1 MB has been tested and

initialized. Adjusting the displayed memory size for
relocation and shadowing next.

51 The memory size display was adjusted for relocation

and shadowing. Testing the memory above 1 MB next.

52 The memory above 1 MB has been tested and

initialized. Saving the memory size information next.

53 The memory size information and the CPU registers are

saved. Entering real mode next.

54 Shutdown was successful. The CPU is in real mode.

Disabling the Gate A20 line, parity, and the NMI next.

57 The A20 address line, parity, and the NMI are

disabled. Adjusting the memory size depending on
relocation and shadowing next.

58 The memory size was adjusted for relocation and

shadowing. Clearing the Hit <DEL> message next.

59 The Hit <DEL> message is cleared. The <WAIT>

message is displayed. Starting the DMA and interrupt
controller test next.

BIOS User’s Manual

B-6

Check
PointDescription

60 The DMA page register test passed. Performing the

DMA Controller 1 base register test next.

62 The DMA controller 1 base register test passed.

Performing the DMA controller 2 base register test next.

65 The DMA controller 2 base register test passed.

Programming DMA controllers 1 and 2 next.

66 Completed programming DMA controllers 1 and 2.

Initializing the 8259 interrupt controller next.

7F Extended NMI source enabling is in progress.

80 The keyboard test has started. Clearing the output

buffer and checking for stuck keys. Issuing the
keyboard reset command next.

81 A keyboard reset error or stuck key was found. Issuing

the keyboard controller interface test command next.

82 The keyboard controller interface test completed.

Writing the command byte and initializing the circular
buffer next.

83 The command byte was written and global data

initialization has been completed. Checking for a
locked key next.

84 Locked key checking is over. Checking for a memory

size mismatch with CMOS RAM data next.

85 The memory size check is done. Displaying a soft error

and checking for a password or bypassing WINBIOS
Setup next.

86 The password was checked. Performing any required

programming before WINBIOS Setup next.

B-7

Appendix B: AMIBIOS POST Diagnostics Error Messages

Check
PointDescription

87 The programming before WINBIOS Setup has

been completed. Uncompressing the WINBIOS Setup
code and executing the AMIBIOS Setup or WINBIOS
Setup utility next.

88 Returned from WINBIOS Setup and cleared the screen.

Performing any necessary programming after WINBIOS
Setup next.

89 The programming after WINBIOS Setup has been

completed. Displaying the power-on screen message
next.

8B The first screen message has been displayed. The

<WAIT...> message is displayed. Performing the PS/2
mouse check and extended BIOS data area allocation
check next.

8C Programming the WINBIOS Setup options next.

8D The WINBIOS Setup options are programmed.

Resetting the hard disk controller next.

8F The hard disk controller has been reset. Configuring the

floppy drive controller next.

91 The floppy drive controller has been configured.

Configuring the hard disk drive controller next.

95 Initializing the bus option ROMs from C800 next.

96 Initializing before passing control to the adaptor ROM at

C800.

97 Initialization before the C800 adaptor ROM gains

control has been completed. The adaptor ROM check
is next.

98 The adaptor ROM had control and has now returned

control to BIOS POST. Performing any required
processing after the option ROM returned control.

BIOS User’s Manual

B-8

Check
PointDescription

99 Any initialization required after the option ROM test has

been completed. Configuring the timer data area and
printer base address next.

9A Set the timer and printer base addresses. Setting the

RS-232 base address next.

9B Returned after setting the RS-232 base address.

Performing any required initialization before the
Coprocessor test next.

9C Required initialization before the Coprocessor test is

over. Initializing the Coprocessor next.

9D Coprocessor initialized. Performing any required

initialization after the Coprocessor test next.

9E Initialization after the Coprocessor test is complete.

Checking the extended keyboard, keyboard ID, and
Num Lock key next. Issuing the keyboard ID command
next.

A2 Displaying any soft errors next.

A3 The soft error display has completed. Setting the

keyboard typematic rate next.

A4 The keyboard typematic rate is set. Programming the

memory wait states next.

A5 Memory wait state programming is over. Clearing the

screen and enabling parity and the NMI next.

A7 NMI and parity enabled. Performing any initialization

required before passing control to the adaptor ROM at
E000 next.

A8 Initialization before passing control to the adaptor ROM

at E000h completed. Passing control to the adaptor
ROM at E000h next.

B-9

Appendix B: AMIBIOS POST Diagnostics Error Messages

Check
PointDescription

A9 Returned from adaptor ROM at E000h control.

Next, performing any initialization required after
the E000 option ROM had control.

AA Initialization after E000 option ROM control has

completed. Displaying the system configuration next.

AB Building the multiprocessor table, if necessary. POST

next.

B0 The system configuration is displayed.

AC Uncompressing the DMI data and initializing DMI.

B1 Copying any code to specific areas.

D0h The NMI is disabled. Power on delay is starting.

Next, the initialization cade checksum will be verified.

D1h Initializing the DMA controller. Performing the keyboard

controller BAT test. Starting memory refresh, and
entering 4 GB flat mode next.

D3h Starting memory sizing next.

D4h Returning to real mode. Executing any OEM patches

and setting the stack next.

D5h Passing control to the uncompressed code in shadow

RAM at E000:0000h. The initialization code is copied
to segment 0 and control will be transferred to segment

0.

D6h Control is in segment 0. Next, checking if

<Ctrl><Home>was pressed and verifying the system
BIOS checksum.

BIOS User’s Manual

B-10

If either <Ctrl><Home> was pressed or the system BIOS
checksum is bad, the system will next go to checkpoint code
E0h.

Otherwise, going to checkpoint code D7h.