Supero SC835 Chassis Series, SC835TQ-R800B User Manual

SC835 Chassis

Series

SC835TQ - R800B

USER’S MANUAL

1.0b

SUPER

®

SC835 Chassis Manual

ii

Manual Revision 1.0b
Release Date: December 16, 2009

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software, if any,
and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or
reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.

Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.

Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2009 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

iii

Preface

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It

provides information for the installation and use of the SC835 3U chassis. Installa-

tion and maintenance should be performed by experienced technicians only.

Supermicro’s SC835 3U chassis features a unique and highly-optimized design for

dual-core Xeon platforms. The chassis is equipped with a redundant 800W high-

efciency power supply. High-performance fans provide ample optimized cooling for

FB-DIMM memory modules and 8 hot-swappable drive bays offer maximum storage

capacity in a 3U form factor.

This document lists compatible parts available when this document was published.

Always refer to the our Web site for updates on supported parts and congura-

tions.

SC835 Chassis Manual

iv

Manual Organization

Chapter 1: Introduction

The rst chapter provides a checklist of the main components included with this

chassis and describes the main features of the SC835 chassis. This chapter also

includes contact information.

Chapter 2: System Safety

This chapter lists warnings, precautions, and system safety. You should thoroughly

familiarize yourself with this chapter for a general overview of safety precautions

that should be followed before installing and servicing this chassis.

Chapter 3: Chassis Components

Refer here for details on this chassis model including the fans, bays, airow shields,

and other components.

Chapter 4: System Interface

Chapter 4 provides details on the system interface, which includes the functions

and information provided by the control panel on the chassis as well as other LEDs

located throughout the system.

Chapter 5: Chassis Setup and Maintenance

Refer to this chapter for detailed information on this chassis. You should follow the

procedures given in this chapter when installing, removing, or reconguring your

chassis.

Chapter 6: Rack Installation

This chapter details information on chassis rack installation. You should follow the

procedures given in this chapter when installing, removing or reconguring your

chassis into a rack environment.

Appendix A: SC835 Chassis Cables

Appendix B: SC835 Power Supply Specications

Appendix C: SAS-833TQ Series Backplane

v

Preface

Table of Contents

Chapter 1 Introduction

1-1 Overview ......................................................................................................... 1-1

1-2 Shipping List .................................................................................................... 1-1

Part Numbers .................................................................................................. 1-1

1-3 Chassis Features ............................................................................................ 1-2

CPU Support ................................................................................................... 1-2

Hard Drives ..................................................................................................... 1-2

I/O Expansion slots ......................................................................................... 1-2

Peripheral Drives ............................................................................................. 1-2

Other Features ................................................................................................ 1-2

1-4 Contacting Supermicro .................................................................................... 1-3

Chapter 2 System Safety

2-1 Overview ......................................................................................................... 2-1

2-2 Warnings and Precautions .............................................................................. 2-1

2-3 Preparing for Setup ......................................................................................... 2-1

2-4 Electrical Safety Precautions .......................................................................... 2-2

2-5 General Safety Precautions ............................................................................ 2-3

2-6 System Safety ................................................................................................. 2-3

Chapter 3 Chassis Components

3-1 Overview ......................................................................................................... 3-1

3-2 Components .................................................................................................... 3-1

Chassis and Hard Drive Bays ......................................................................... 3-1

Backplane ........................................................................................................ 3-1

Fans ................................................................................................................3-1

Mounting Rails ................................................................................................ 3-2

Power Supply .................................................................................................. 3-2

Air Shroud ....................................................................................................... 3-2

3-3 Where to get Replacement Components ........................................................ 3-2

Chapter 4 System Interface

4-1 Overview ......................................................................................................... 4-1

4-2 Control Panel Buttons ..................................................................................... 4-2

4-3 Control Panel LEDs ........................................................................................ 4-2

4-4 Drive Carrier LEDs .......................................................................................... 4-4

Chapter 5 Chassis Setup and Maintenance

5-1 Overview ......................................................................................................... 5-1

5-2 Removing the Chassis Cover ......................................................................... 5-2

SC835 Chassis Manual

vi

5-3 Installing the Hard Drives ................................................................................ 5-3

Removing Hard Drive Carriers From the Chassis .......................................... 5-3

Installing a Hard Drive into the Hard Drive Carrier ......................................... 5-4

5-4 Installing the Motherboard .............................................................................. 5-6

Permanent and Optional Standoffs ................................................................. 5-6

Standoff Labeling ............................................................................................ 5-6

I/O Shield and Expansion Card Setup ............................................................ 5-8

Installing an I/O Port Panel ............................................................................. 5-9

5-5 Installing the Air Shroud, Rear Fan, and Checking Air Flow ........................ 5-10

5-6 Chassis Maintenance .....................................................................................5-11

System Fans ..................................................................................................5-11

Replacing a System Fan ................................................................................5-11

Installing the Rear System Fans ................................................................... 5-12

Checking the Server's Air Flow ..................................................................... 5-13

5-7 Power Supply ................................................................................................ 5-14

Replacing the Power Supply ......................................................................... 5-14

Replacing the Power Distributor ................................................................... 5-15

Replacing the DVD or CD-ROM Drive .......................................................... 5-16

Replacing or Installing the DVD Drive .......................................................... 5-16

Chapter 6 Rack Installation

6-1 Overview ......................................................................................................... 6-1

6-2 Unpacking the System .................................................................................... 6-1

6-3 Preparing for Setup ......................................................................................... 6-1

Choosing a Setup Location ............................................................................. 6-1

Rack Precautions ............................................................................................ 6-2

General Server Precautions ............................................................................ 6-2

Rack Mounting Considerations ....................................................................... 6-3

Reduced Airow ......................................................................................... 6-3

Mechanical Loading ................................................................................... 6-3

Circuit Overloading ..................................................................................... 6-3

Reliable Ground ......................................................................................... 6-3

6-4 Rack Mounting Instructions ............................................................................. 6-4

Separating the Sections of the Rack Rails ..................................................... 6-4

Installing the Inner Rail Extension .................................................................. 6-5

Outer Rack Rails ............................................................................................. 6-6

vii

Preface

Appendix A SC835 Chassis Cables

Appendix B SC835 Power Supply Specications

Appendix C SAS-833TQ Backplane Specications

SC835 Chassis Manual

viii

Notes

1-1

Chapter 1: Introduction

Chapter 1

Introduction

1-1 Overview

Supermicro’s SC835 3U chassis features a unique and highly-optimized design.

The chassis is equipped with a redundant high-efciency power supply. High-

performance fans provide ample optimized cooling and 8 hot-swappable drive bays

offer maximum storage capacity in a 3U form factor.

1-2 Shipping List

Part Numbers

Please visit the following link for the latest shipping lists and part numbers for your

particular chassis model:

http://www.supermicro.com/products/chassis/3U/?chs=835

SC835 Chassis Series

Model CPU HDD I/O Slots

Power

Supply

SC835TQ-R800B DP/UP

8x 3.5" SAS

/ SATA hot

swappable

drive trays

7x FF R800W

SC835 Chassis Manual

1-2

1-3 Chassis Features

The SC835 high-performance chassis includes the following features:

CPU Support

The SC835 chassis supports Intel and AMD Quad processors. Please refer to the

motherboard specications pages on our Web site for updates on supported proces-

sors for this chassis, at www.supermicro.com.

Hard Drives

The SC835 chassis features eight slots for 3.5" SAS/SATA drives. These drives are

hot swappable. Once setup correctly, these drives can be removed without powering

down the server. In addition, these drives support SES2 (SAS/SATA).

I/O Expansion slots

Each version of the SC835 chassis includes 7 full-height, full-length I/O expansion

slots.

Peripheral Drives

Each SC835 chassis supports either one slim 8x DVD drive or one 24x CD. These

drives allow you to quickly install or save data.

Other Features

Other onboard features are included to promote system health. These include

various six cooling fans, a convenient power switch, reset button, and LED indica-

tors.

1-3

Chapter 1: Introduction

1-4 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Asia-Pacic

Address: Super Micro Computer, Inc.

4F, No. 232-1, Liancheng Rd.

Chung-Ho 235, Taipei County

Taiwan, R.O.C.

Tel: [phone]

Fax: [phone]

Web Site: www.supermicro.com.tw

Technical Support:

Email: [e-mail]

Tel: [phone]

SC835 Chassis Manual

1-4

Notes

2-1

Chapter 2: System Safety

Chapter 2

System Safety

2-1 Overview

This chapter provides a quick setup checklist to get your chassis up and running.

Following the steps in order given should enable you to have your chassis setup and

operational within a minimal amount of time. These instructions assume that you are

an experienced technician, familiar with common concepts and terminology.

2-2 Warnings and Precautions

You should inspect the box the chassis was shipped in and note if it was damaged

in any way. If the chassis itself shows damage, le a damage claim with the carrier

who delivered your system.

Decide on a suitable location for the rack unit that will hold the chassis. It should be

situated in a clean, dust-free area that is well ventilated. Avoid areas where heat,

electrical noise and electromagnetic elds are generated.

You will also need it placed near at least two grounded power outlets. The SC835

chassis includes two redundant power supplies which require two grounded out-

lets.

2-3 Preparing for Setup

The SC835 chassis includes a set of rail assemblies, and the mounting brackets

and mounting screws you will need to install the system into a rack. Please read

this manual in its entirety before you begin the installation procedure.

SC835 Chassis Manual

2-2

2-4 Electrical Safety Precautions

Basic electrical safety precautions should be followed to protect yourself from harm

and the SC835 from damage:

Be aware of the locations of the power on/off switch on the chassis as well •

as the room’s emergency power-off switch, disconnection switch or electrical

outlet. If an electrical accident occurs, you can then quickly remove power from

the system.

Do not work alone when working with high-voltage components.•

Power should always be disconnected from the system when removing or in-•

stalling main system components, such as the serverboard, memory modules

and the DVD-ROM (not necessary for hot-swappable drives). When discon-

necting power, you should rst power-down the system with the operating

system and then unplug the power cords from all the power supply modules

in the system.

When working around exposed electrical circuits, another person who is fa-•

miliar with the power-off controls should be nearby to switch off the power, if

necessary.

Use only one hand when working with powered-on electrical equipment. This •

is to avoid making a complete circuit, which will cause electrical shock. Use

extreme caution when using metal tools, which can easily damage any electrical

components or circuit boards they come into contact with.

Do not use mats designed to decrease electrostatic discharge as protection from •

electrical shock. Instead, use rubber mats that have been specically designed

as electrical insulators.

The power supply power cord must include a grounding plug and must be •

plugged into grounded electrical outlets.

Serverboard battery: CAUTION - There is a danger of explosion if the onboard •

battery is installed upside down, which will reverse its polarities This battery

must be replaced only with the same or an equivalent type recommended by

the manufacturer. Dispose of used batteries according to the manufacturer’s

instructions.

2-3

Chapter 2: System Safety

Please handle used batteries carefully. Do not damage the battery in any way; •

a damaged battery may release hazardous materials into the environment. Do

not discard a used battery in the garbage or a public landll. Please comply

with the regulations set up by your local hazardous waste management agency

to dispose of your used battery properly.

DVD-ROM laser: CAUTION - This server may have come equipped with a •

DVD-ROM drive. To prevent direct exposure to the laser beam and hazardous

radiation exposure, do not open the enclosure or use the unit in any uncon-

ventional way.

2-5 General Safety Precautions

Keep the area around the chassis clean and free of clutter.•

Place the chassis top cover and any system components that have been re-•

moved away from the system or on a table so that they won’t accidentally be

stepped on.

While working on the system, do not wear loose clothing such as neckties and •

unbuttoned shirt sleeves, which can come into contact with electrical circuits or

be pulled into a cooling fan.

Remove any jewelry or metal objects from your body, which are excellent metal •

conductors that can create short circuits and harm you if they come into contact

with printed circuit boards or areas where power is present.

After accessing the inside of the system, close the system back up and secure •

it to the rack unit with the retention screws after ensuring that all connections

have been made.

2-6 System Safety

Electrostatic discharge (ESD) is generated by two objects with different electrical

charges coming into contact with each other. An electrical discharge is created to

neutralize this difference, which can damage electronic components and printed

circuit boards. The following measures are generally sufcient to neutralize this

difference before contact is made to protect your equipment from ESD:

Do not use mats designed to decrease electrostatic discharge as protection from •

electrical shock. Instead, use rubber mats that have been specically designed

as electrical insulators.

SC835 Chassis Manual

2-4

Use a grounded wrist strap designed to prevent static discharge.•

Keep all components and printed circuit boards (PCBs) in their antistatic bags •

until ready for use.

Touch a grounded metal object before removing any board from its antistatic •

bag.

Do not let components or PCBs come into contact with your clothing, which may •

retain a charge even if you are wearing a wrist strap.

Handle a board by its edges only; do not touch its components, peripheral chips, •

memory modules or contacts.

When handling chips or modules, avoid touching their pins.•

Put the serverboard and peripherals back into their antistatic bags when not •

in use.

For grounding purposes, make sure your computer chassis provides excellent •

conductivity between the power supply, the case, the mounting fasteners and

the serverboard.

3-1

Chapter 3: Chassis Components

Chapter 3

Chassis Components

3-1 Overview

This chapter describes the most common components included with your chassis.

Some components listed may not be included or compatible with your particular

chassis model. For more information, see the installation instructions detailed later

in this manual.

3-2 Components

Chassis and Hard Drive Bays

The SC835 chassis supports either one slim 8x DVD or one 24x CD-ROM drive.

It includes eight hard drive bays. Most chassis models include a DVD-ROM. Hard

drives must be purchased separately. For the latest shipping lists, visit our Web site

at: http://www.supermicro.com.

Backplane

Each SC835 chassis comes with a 3U backplane. Depending on our order, your

backplane will accept SAS/SATA drives or SAS only. For more information regarding

compatible backplanes, view the appendices found at the end of this manual. In

addition, visit our Web site for the latest information: http://www.supermicro.com.

Fans

The SC835 chassis accepts three 8cm hot-swappable fans and two 8cm rear

exhaust fans. System fans for SC835 chassis are powered from the serverboard.

These fans are 3U compatible and are powered by 3-pin connectors.

SC835 Chassis Manual

3-2

Mounting Rails

The SC835 can be placed in a rack for secure storage and use. To set up your

rack, follow the step-by-step instructions included in this manual.

Power Supply

Each SC835 chassis model includes two redundant high-efciency hot-swappable

power supplies rated at 800 Watts. In the unlikely event of a failure in one of the

power supplies, you can remove and replace the faulty power supply without pow-

ering down the system.

Air Shroud

Air shrouds are shields, usually plastic, that funnel air directly to where it is needed.

Always use the air shroud included with your chassis.

3-3 Where to get Replacement Components

although not frequently, you may need replacement parts for your system. To en-

sure the highest level of professional service and technical support, we strongly

recommend purchasing exclusively from our Supermicro Authorized Distributors/

System Integrators/Resellers. A list of Supermicro Authorized Distributors/System

Integrators/Reseller can be found at: http://www.supermicro.com. Click the Where

to Buy link.

4-1

Chapter 4: System Interface

Chapter 4

System Interface

4-1 Overview

There are several LEDs on the control panel as well as others on the drive carriers

to keep you constantly informed of the overall status of the system as well as the

activity and health of specic components. Most SC835 models have two buttons

on the chassis control panel: a reset button and an on/off switch. This chapter ex-

plains the meanings of all LED indicators and the appropriate response you may

need to take.

Figure 4-1: SC835 Front Panel

SC835 Chassis Manual

4-2

4-2 Control Panel Buttons

There are t wo push-but tons located on the front of the chassis. These are (in order

from left to right) a reset button and a power on/off button.

Reset:• The reset button is used to reboot the system.

Power:• The main power switch is used to apply or remove power from the

power supply to the server system. Turning off system power with this button

removes the main power but keeps standby power supplied to the system.

Therefore, you must unplug system before servicing.

4-3 Control Panel LEDs

The control panel located on the front of the SC835 chassis has six LEDs. These

LEDs provide you with critical information related to different parts of the system.

This section explains what each LED indicates when illuminated and any correc-

tive action you may need to take.

 Power Failure: When this LED ashes, it indicates a power failure in the

power supply.

!