Supero SC825TQ-R720UB, SC825TQ-560LPV, SC825TQ-710LP, SC825TQ-R700LPV, SC825S2-R700LPV User Manual

SC825 CHASSIS

Series

SC825TQ-R720LPB SC825TQ-R720UB

SC825TQ-R700V(B) SC825TQ-710LP(B)

SC825TQ-R700LPV(B) SC825TQ-560LPV(B)

SC825S2-R700LPV(B) SC825S2-560LPV(B)

SC825TQ-560UV(B) SC825TQ-560UB(B)

USER’S MANUAL

1.0b

SUPER

®

SC825 Chassis Manual

ii

Manual Revision 1.0b
Release Date: December 28, 2009

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software, if any,
and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or
reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.

Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.

Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2009 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

iii

Preface

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It

provides information for the installation and use of the SC825 2U chassis. Installa-

tion and maintenance should be performed by experienced technicians only.

Supermicro’s SC825 2U chassis features a unique and highly optimized design. The

chassis is equipped with a 720W (redundant), 710W (single), 700W (redundant)

or 560W (single) high-efciency power supply for superb power savings. High-

performance fans provide ample optimized cooling for the chassis.

This document lists compatible parts and congurations available when this docu-

ment was published. Always refer to the our Web site for updates on supported

parts and congurations.

SC825 Chassis Manual

iv

Manual Organization

Chapter 1: Introduction

The rst chapter provides a checklist of the main components included with this

chassis and describes the main features of the SC825 chassis. This chapter also

includes contact information.

Chapter 2: System Safety

This chapter lists warnings, precautions, and system safety. You should thoroughly

familiarize yourself with this chapter for a general overview of safety precautions

that should be followed before installing and servicing this chassis.

Chapter 3: Chassis Components

Refer here for details on this chassis model including the fans, bays, airow shields,

and other components.

Chapter 4: System Interface

Refer to this chapter for details on the system interface, which includes the functions

and information provided by the control panel on the chassis as well as other LEDs

located throughout the system.

Chapter 5: Chassis Setup and Maintenance

Refer to this chapter for detailed information on this chassis. You should follow the

procedures given in this chapter when installing, removing, or reconguring your

chassis.

Chapter 6: Rack Installation

Refer to this chapter for detailed information on chassis rack installation. You should

follow the procedures given in this chapter when installing, removing or reconguring

your chassis into a rack environment.

v

Preface

Appendices

This section lists compatible cables, power supply specications, and compatible

backplanes. Not all compatible backplanes may be listed. Refer to our Web site

for the latest compatible backplane information.

SC825 Chassis Manual

vi

Table of Contents

Chapter 1 Introduction

1-1 Overview ......................................................................................................... 1-1

1-2 Shipping List .................................................................................................... 1-1

1-3 Chassis Features ............................................................................................ 1-2

CPU ................................................................................................................. 1-2

Hard Drives ..................................................................................................... 1-2

I/O Expansion slots ......................................................................................... 1-2

Peripheral Drives ............................................................................................. 1-2

Other Features ................................................................................................ 1-2

1-4 Contacting Supermicro .................................................................................... 1-3

1-5 Returning Merchandise for Service................................................................. 1-4

Chapter 2 System Safety

2-1 Overview ......................................................................................................... 2-1

2-2 Warnings and Precautions .............................................................................. 2-1

2-3 Preparing for Setup ......................................................................................... 2-1

2-4 Electrical Safety Precautions .......................................................................... 2-2

2-5 General Safety Precautions ............................................................................ 2-3

2-6 System Safety ................................................................................................. 2-3

Chapter 3 Chassis Components

3-1 Overview ......................................................................................................... 3-1

3-2 Components .................................................................................................... 3-1

Chassis ............................................................................................................ 3-1

Backplane ........................................................................................................ 3-1

Fans ................................................................................................................3-1

Mounting Rails ................................................................................................ 3-1

Power Supply .................................................................................................. 3-2

Air Shroud ....................................................................................................... 3-2

3-3 Where to get Replacement Components ........................................................ 3-2

Chapter 4 System Interface

4-1 Overview ......................................................................................................... 4-1

4-2 Control Panel Buttons ..................................................................................... 4-2

4-3 Control Panel LEDs ........................................................................................ 4-2

4-4 Drive Carrier LEDs .......................................................................................... 4-4

SAS/SATA Drives ............................................................................................ 4-4

SCSI Drives ..................................................................................................... 4-4

vii

Preface

Chapter 5 Chassis Setup and Maintenance

5-1 Overview ......................................................................................................... 5-1

5-2 Installation and General Maintnenance .......................................................... 5-1

Installation ....................................................................................................... 5-1

5-3 Removing the Chassis Cover ......................................................................... 5-2

5-4 Installing Hard Drives ...................................................................................... 5-3

5-5 Installing an Optional Floppy or Fixed Hard Drive .......................................... 5-6

5-6 DVD-ROM Replacement or Installation .......................................................... 5-7

Replacing the DVD-ROM and Front Panel ..................................................... 5-7

5-7 Installing the Motherboard .............................................................................. 5-8

I/O Shield ........................................................................................................ 5-8

Installing the I/O Shield ................................................................................... 5-8

Permanent and Optional Standoffs ................................................................. 5-9

Add-on Card/Expansion Slot Setup ...............................................................5-11

Add-on Card/Expansion Slot Setup in LP (Low Prole) Chassis ..................5-11

Add-on Card/Expansion Slot Setup for SC825U (Universal Output)............ 5-12

5-8 Installing the Air Shroud ................................................................................ 5-13

Checking the Server's Air Flow ..................................................................... 5-14

Installation Complete ..................................................................................... 5-14

5-9 System Fans ................................................................................................. 5-15

5-10 Power Supply ............................................................................................... 5-17

Power Supply Failure .................................................................................... 5-17

Replacing the Power Distributor ................................................................... 5-19

Replacing or Installing the Front Port Panel ................................................. 5-20

5-11 Optional Front Bezel ..................................................................................... 5-21

Chapter 6 Rack Installation

6-1 Overview ......................................................................................................... 6-1

6-2 Unpacking the System .................................................................................... 6-1

6-3 Preparing for Setup ......................................................................................... 6-1

Choosing a Setup Location ............................................................................. 6-1

Rack Precautions ............................................................................................ 6-2

General Server Precautions ............................................................................ 6-2

Rack Mounting Considerations ....................................................................... 6-3

Ambient Operating Temperature ................................................................ 6-3

Reduced Airow ......................................................................................... 6-3

Mechanical Loading ................................................................................... 6-3

Circuit Overloading ..................................................................................... 6-3

Reliable Ground ......................................................................................... 6-3

SC825 Chassis Manual

viii

6-4 Rack Mounting Instructions ............................................................................. 6-4

Separating the Sections of the Rack Rails ..................................................... 6-4

Installing the Inner Rail Extension .................................................................. 6-5

Outer Rack Rails ............................................................................................. 6-6

Appendix A SC825 Chassis Cables

Appendix B SC825 Power Supply Specications

Appendix C SAS-825TQ Backplane Specications

Appendix D SCA-825S2 Backplane Specications

Chapter 1

Introduction

1-1 Overview

Supermicro’s SC825 2U chassis features a unique and highly-optimized design.

The chassis is equipped with high efciency power supply.

1-2 Shipping List

Please visit the following link for the latest shipping lists and part numbers for

your particular chassis model http://www.supermicro.com/products/chassis/1U/

?chs=825

Chapter 1: Introduction

1-1

SC825 Chassis

Model CPU HDD I/O Slots

Power

Supply

SC825TQ-720LPB

DP Xeon 8x SAS / SATA 7x LP, FL

720W

(Gold Level)

SC825TQ-720UB

DP Xeon 8x SAS / SATA

4x FF
3x LP

720W

(Gold Level)

SC825TQ-710LP

DP Xeon 8x SAS / SATA 7x LP, FL 710W

SC825TQ-R700UV /
SC825TQ-R700UB

DP Xeon 8x SAS / SATA

4x FF
3x LP

700W Re-

dundant

SC825TQ-R700LPV /
SC825TQ-R700LPB

DP Xeon 8x SAS / SATA 7x LP

700W

Redundant

SC825S2-R700LPV /
SC825S2-R700LPB

DP Xeon

8x Dual-Channel

U320 SCSI

7x LP

700W

Redundant

SC825TQ-560UV /
SC825TQ-560UB

DP Xeon 8x SAS / SATA

4x FF
3x LP

560W

SC825TQ-560LPV /
SC825TQ-560LPB

DP Xeon 8x SAS / SATA 7x LP 560W

SC825S2-560LPV /
SC825S2-560LPB

DP Xeon

8x Dual-Channel

U320 SCSI

7x LP 560W

SC825 Chassis Manual

1-2

1-3 Chassis Features

The SC825 2U, high-performance chassis includes the following features:

CPU

The SC825 chassis supports a dual-core Xeon processor. Please refer to the

motherboard specications pages on our web site for updates on supported pro-

cessors.

Hard Drives

The SC825 chassis features 8 slots for U320 SCSI or SAS/SATA drives. These

drives are hot-swappable. Once set up correctly, these drives can be removed

without powering down the server. In addition, these drives support SAF-TE (SCSI)

and SES2 (SAS/SATA).

I/O Expansion slots

Each SC825 chassis model includes seven low-prole I/O expansion slots.

Peripheral Drives

Each SC825 chassis supports one slim DVD-ROM drive (included) and one slim

oppy drive (optional). These drives allow you to quickly install or save data.

Other Features

Other onboard features are included to promote system health. These include

various three cooling fans, a convenient power switch, reset button, and ve LED

indicators.

1-3

Chapter 1: Introduction

1-4 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Asia-Pacic

Address: Super Micro Computer, Inc.

4F, No. 232-1, Liancheng Rd.

Chung-Ho 235, Taipei County

Taiwan, R.O.C.

Tel: [phone]

Fax: [phone]

Web Site: www.supermicro.com.tw

Technical Support:

Email: [e-mail]

Tel: [phone]

SC825 Chassis Manual

1-4

1-5 Returning Merchandise for Service

A receipt or copy of your invoice marked with the date of purchase is required be-

fore any warranty service will be rendered. You can obtain service by calling your

vendor for a Returned Merchandise Authorization (RMA) number. When returning

to the manufacturer, the RMA number should be prominently displayed on the

outside of the shipping carton, and mailed prepaid or hand-carried. Shipping and

handling charges will be applied for all orders that must be mailed when service

is complete.

For faster service, RMA authorizations may be requested online (http://www.

supermicro.com/support/rma/).

Whenever possible, repack the chassis in the original Supermicro carton, using the

original packaging material. If these are no longer available, be sure to pack the

chassis securely, using packaging material to surround the chassis so that it does

not shift within the carton and become damaged during shipping.

This warranty only covers normal consumer use and does not cover damages in-

curred in shipping or from failure due to the alteration, misuse, abuse or improper

maintenance of products.

During the warranty period, contact your distributor rst for any product problems.

2-1

Chapter 2: System Safety

Chapter 2

System Safety

2-1 Overview

This chapter provides a quick setup checklist to get your chassis up and running.

Following the steps in order given should enable you to have your chassis setup and

operational within a minimal amount of time. This quick set up assumes that you

are an experienced technician, familiar with common concepts and terminology.

2-2 Warnings and Precautions

You should inspect the box the chassis was shipped in and note if it was damaged

in any way. If the chassis itself shows damage, le a damage claim with carrier

who delivered your system.

Decide on a suitable location for the rack unit that will hold that chassis. It should

be situated in a clean, dust-free area that is well ventilated. Avoid areas where

heat, electrical noise and electromagnetic elds are generated.

You will also need it placed near at least one grounded power outlet. When con-

gured, the SC825 chassis includes one power supply. "R" models (i.e. SC825S-

R700V Chassis) include a redundant power supply and require two grounded

outlets.

2-3 Preparing for Setup

The SC825 Chassis includes a set of rail assemblies, including mounting brackets

and mounting screws you will need to install the systems into the rack. Please read

this manual in its entirety before you begin the installation procedure.

SC825 Chassis Manual

2-2

2-4 Electrical Safety Precautions

Basic electrical safety precautions should be followed to protect yourself from harm

and the SC825 from damage:

Be aware of the locations of the power on/off switch on the chassis as well •

as the room’s emergency power-off switch, disconnection switch or electrical

outlet. If an electrical accident occurs, you can then quickly remove power from

the system.

Do not work alone when working with high voltage components.•

Power should always be disconnected from the system when removing or in-•

stalling main system components, such as the serverboard, memory modules

and the DVD-ROM and oppy drives (not necessary for hot swappable drives).

When disconnecting power, you should rst power down the system with the

operating system and then unplug the power cords from all the power supply

modules in the system.

When working around exposed electrical circuits, another person who is fa-•

miliar with the power-off controls should be nearby to switch off the power, if

necessary.

Use only one hand when working with powered-on electrical equipment. This •

is to avoid making a complete circuit, which will cause electrical shock. Use

extreme caution when using metal tools, which can easily damage any electrical

components or circuit boards they come into contact with.

Do not use mats designed to decrease electrostatic discharge as protection from •

electrical shock. Instead, use rubber mats that have been specically designed

as electrical insulators.

The power supply power cord must include a grounding plug and must be •

plugged into grounded electrical outlets.

Serverboard battery: CAUTION - There is a danger of explosion if the onboard •

battery is installed upside down, which will reverse its polarities This battery

must be replaced only with the same or an equivalent type recommended by

the manufacturer. Dispose of used batteries according to the manufacturer’s

instructions.

2-3

Chapter 2: System Safety

Please handle used batteries carefully. Do not damage the battery in any way; •

a damaged battery may release hazardous materials into the environment. Do

not discard a used battery in the garbage or a public landll. Please comply

with the regulations set up by your local hazardous waste management agency

to dispose of your used battery properly.

DVD-ROM laser: CAUTION - this server may have come equipped with a •

DVD-ROM drive. To prevent direct exposure to the laser beam and hazardous

radiation exposure, do not open the enclosure or use the unit in any uncon-

ventional way.

2-5 General Safety Precautions

Keep the area around the chassis clean and free of clutter.•

Place the chassis top cover and any system components that have been re-•

moved away from the system or on a table so that they won’t accidentally be

stepped on.

While working on the system, do not wear loose clothing such as neckties and •

unbuttoned shirt sleeves, which can come into contact with electrical circuits or

be pulled into a cooling fan.

Remove any jewelry or metal objects from your body, which are excellent metal •

conductors that can create short circuits and harm you if they come into contact

with printed circuit boards or areas where power is present.

After accessing the inside of the system, close the system back up and secure •

it to the rack unit with the retention screws after ensuring that all connections

have been made.

2-6 System Safety

Electrostatic discharge (ESD) is generated by two objects with different electrical

charges coming into contact with each other. An electrical discharge is created to

neutralize this difference, which can damage electronic components and printed

circuit boards. The following measures are generally sufcient to neutralize this

difference before contact is made to protect your equipment from ESD:

Do not use mats designed to decrease electrostatic discharge as protection from •

electrical shock. Instead, use rubber mats that have been specically designed

as electrical insulators.

SC825 Chassis Manual

2-4

Use a grounded wrist strap designed to prevent static discharge.•

Keep all components and printed circuit boards (PCBs) in their antistatic bags •

until ready for use.

Touch a grounded metal object before removing any board from its antistatic •

bag.

Do not let components or PCBs come into contact with your clothing, which may •

retain a charge even if you are wearing a wrist strap.

Handle a board by its edges only; do not touch its components, peripheral chips, •

memory modules or contacts.

When handling chips or modules, avoid touching their pins.•

Put the serverboard and peripherals back into their antistatic bags when not •

in use.

For grounding purposes, make sure your computer chassis provides excellent •

conductivity between the power supply, the case, the mounting fasteners and

the serverboard.

3-1

Chapter 3: Chassis Components

Chapter 3

Chassis Components

3-1 Overview

This chapter describes the most common components included with your chassis.

Some components listed may not be included or may not be compatible with your

particular chassis model. For more information, see the installation instructions

detailed later in this manual.

3-2 Components

Chassis

The SC825 chassis includes eight hard drive bays. Most chassis models come with

a DVD-ROM. Hard drives must be purchased separately. For the latest shipping

lists, visit our Web site at: http://www.supermicro.com.

This chassis supports a 2U backplane, 3 fans and one (sometimes two) power

supplies. SC825 models come in silver or black.

Backplane

Each SC825 chassis comes with a 2U backplane. Depending on our order, you

backplane will accept SAS/SATA or SCSI. For more information regarding compat-

ible backplanes, view the appendices found at the end of this manual. In addition,

visit our Web site for the latest information: http://www.supermicro.com.

Fans

The SC825 chassis supports three system fans. System fans for SC825 chassis

are powered from the motherboard. These fans are 2U high and are powered by

3-pin connectors.

Mounting Rails

The SC825 can be placed in a rack for secure storage and use. To setup your rack,

follow the step-by-step instructions included in this manual.

SC825 Chassis Manual

3-2

Power Supply

Each SC825 chassis model includes a high-efciency power supply rated at 710

Watts (single), 700 Watts (redundant) or 560W (single). In the unlikely event your

power supply fails, replacement is simple and can be accomplished without tools.

Air Shroud

Air shrouds are shields, usually plastic, which conduct the airow directly to where

it is needed. Always use the air shroud included with your chassis.

3-3 Where to get Replacement Components

Although not frequently, you may need replacement parts for your system. To

ensure the highest level of professional service and technical support, we strongly

recommend purchasing exclusively from our Supermicro Authorized Distributors /

System Integrators / Resellers. A list of Supermicro Authorized Distributors / System

Integrators /Reseller can be found at: http://www.supermicro.com. Click the Where

to Buy link.

4-1

Chapter 4: System Interface

Chapter 4

System Interface

4-1 Overview

There are several LEDs on the control panel and the drive carriers to keep you

constantly informed of the over-all status of the system, as well as the activity and

health of specic components. Most SC825 models have two buttons on the chassis

control panel: a reset button and an on/off switch. This chapter explains the mean-

ings of all LED indicators and the appropriate response you may need to take.

SC825 Chassis Manual

4-2

Power Failure:• When this LED ashes, it indicates a power failure in the power

supply.

Overheat/Fan Fail:• When this LED ashes it indicates a fan failure. When

continuously on (not ashing) it indicates an overheat condition, which may be

caused by cables obstructing the airow in the system or the ambient room

temperature being too warm. Check the routing of the cables and make sure

all fans are present and operating normally. You should also check to make

Power:• The main power switch is used to apply or remove power from the

power supply to the server system. Turning off system power with this button

removes the main power but keeps standby power supplied to the system.

Therefore, you must unplug system before servicing.

4-3 Control Panel LEDs

The control panel located on the front of the SC825 chassis has ve LEDs. These

LEDs provide you with critical information related to different parts of the system.

This section explains what each LED indicates when illuminated and any correc-

tive action you may need to take.

Reset:• The reset button is used to reboot the system.

4-2 Control Panel Buttons

There are t wo push-but tons located on the front of the chassis. These are (in order

from left to right) a reset button and a power on/off button.

!

4-3

Chapter 4: System Interface

Power:• Indicates power is being supplied to the system's power supply units.

This LED should normally be illuminated when the system is operating.

HDD:• Indicates IDE channel activity in the SAS/SATA drive, SCSI drive, and/

or DVD-ROM drive activity when ashing.

NIC1:• Indicates network activity on GLAN1 when ashing.

NIC2:• Indicates network activity on GLAN2 when ashing.

sure that the chassis covers are installed. Finally, verify that the heatsinks are

installed properly. This LED will remain ashing or on as long as the overheat

condition exists.

SC825 Chassis Manual

4-4

4-4 Drive Carrier LEDs

Your chassis uses SAS/SATA or SCSI drives, but not both.

SAS/SATA Drives

Each SAS/SATA drive carrier has two LEDs.

Green:• Each Serial ATA drive carrier has a green LED. When illuminated, this

green LED (on the front of the SATA drive carrier) indicates drive activity. A

connection to the SATA backplane enables this LED to blink on and off when

that particular drive is being accessed.

Red:• The red LED indicates a SAS/SATA drive failure. If one of the SAS/SATA

drives fail, you should be notied by your system management software.

SCSI Drives

Each SCSI drive carrier has two LEDs.

Green:• When illuminated, the green LED on the front of the SCSI drive carrier

indicates drive activity. A connection to the SCSI SCA backplane enables this

LED to blink on and off when that particular drive is being accessed.

Red:• The red LED indicates a drive failure. If one of the SCSI drives fail, you

should be notied by your system management software.

5-1

Chapter 5: Chassis Setup and Maintenance

Chapter 5

Chassis Setup and Maintenance

5-1 Overview

This chapter covers the steps required to install components and perform mainte-

nance on the chassis. The only tool you will need to install components and perform

maintenance is a Phillips screwdriver. Print this page to use as a reference while

setting up your chassis.

5-2 Installation and General Maintnenance

Installation

Removing the Chassis Cover•

Installing Hard Drives•

Installing an Optional Floppy Drive or Fixed Hard Drive•

DVD ROM Replacement or Installation•

Installing the Motherboard (includes I/O Slot Setup)•

Installing the Air Shroud•

General Maintenance

System Fans•

Replacing the Power Supply•

Optional Front Bezel •

Review the warnings and precautions listed in the manual before

setting up or servicing this chassis. These include information in

Chapter 2: System Safety and the warning/precautions listed in the

setup instructions.

!

SC825 Chassis Manual

5-2

5-3 Removing the Chassis Cover

Removing the Chassis Cover

Remove the two screws on each side of the cover, which secure the cover to 1.

the chassis.

Press the release tabs to remove the cover from the locked position. Press 2.

both tabs at the same time.

Once the top cover is released from the locked position, slide the cover 3.

toward the rear of the chassis.

Lift the cover off the chassis.4.

Warning: Except for short periods of time, do NOT operate the

server without the cover in place. The chassis cover must be in

place to allow proper airow and prevent overheating.

Figure 5-1: Removing the Chassis Cover

Release

Tab

Remove

Screw

Remove

Screw

!

2

1

1

1

1

2

3

4

5-3

Chapter 5: Chassis Setup and Maintenance

5-4 Installing Hard Drives

Removing Hard Drive Trays from the Chassis

Press the release button on the drive carrier. This extends the drive carrier 1.

handle.

Use the handle to pull the drive out of the chassis.2.

Figure 5-2: Removing Hard Drive

1

2