Supero SC512F-520, SC512C-260, SC512F-520B, SC512L-260, SC512L-260B User Manual

SC512 CHASSIS

Series

USER’S MANUAL

1.0a

SC512-200B

SC512C-260(B) SC512F-280(B)

SC512F-520(B) SC512L-260(B)

SC512F-520L(B) SC512L-260(B)-LCD

SC512F-410(B) SC512L-200B

SC512F-260(B)

SUPER

®

SC512 Chassis Manual

ii

Manual Revision 1.0a
Release Date: October 1, 2009

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software, if any,
and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or
reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.

Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.

Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2009 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

iii

Preface

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It

provides information for the installation and use of the SC512 1U chassis. Installa-

tion and maintenance should be performed by experienced technicians only.

Supermicro’s SC512 1U chassis features a unique and highly-optimized design for

dual-core Xeon platforms. The chassis is equipped with a 200, 260, 280. 410, or

520 Watt high efciency power supply for superb power savings. High-performance

fans provide ample optimized cooling for FB-DIMM memory modules in a 1U form

factor.

This document lists compatible parts available when this document was published.

Always refer to the our Web site for updates on supported parts and congura-

tions.

SC512 Chassis Manual

iv

Manual Organization

Chapter 1: Introduction

The rst chapter provides a checklist of the main components included with this

chassis and describes the main features. This chapter also includes contact infor-

mation.

Chapter 2: System Safety

This chapter lists warnings, precautions, and system safety. You should thoroughly

familiarize yourself with this chapter for a general overview of safety precautions

that should be followed before installing and servicing this chassis.

Chapter 3: Chassis Components

Refer to this chapter for details on this chassis model including the fans, bays,

airow shields, and other components.

Chapter 4: System Interface

Refer to this chapter for details on the system interface, which includes the functions

and information provided by the control panel on the chassis as well as other LEDs

located throughout the system.

Chapter 5: Chassis Setup and Maintenance

Follow the procedures given in this chapter when installing, removing, or

reconguring your chassis.

Chapter 6: Rack Installation

Refer to this chapter for detailed information on chassis rack installation. You should

follow the procedures given in this chapter when installing, removing or reconguring

your chassis into a rack environment.

Appendix A Cables, Screws, and Other Accessories

Appendix B Power Supply Specications

v

Preface

Table of Contents

About This Manual ............................................................................................. iii

Manual Organization ..........................................................................................iv

Chapter 1 Introduction

1-1 Overview ......................................................................................................... 1-1

1-2 Shipping List .................................................................................................... 1-1

Part Numbers .................................................................................................. 1-1

1-3 Chassis Features ............................................................................................ 1-2

I/O Expansion slots ......................................................................................... 1-2

Peripheral Drives ............................................................................................. 1-2

Dual Hard Drives ............................................................................................. 1-2

1-4 Contacting Supermicro .................................................................................... 1-3

1-5 Returning Merchandise for Service................................................................. 1-4

Chapter 2 System Safety

2-1 Overview ......................................................................................................... 2-1

2-2 Warnings and Precautions .............................................................................. 2-1

2-3 Preparing for Setup ......................................................................................... 2-1

2-4 Electrical Safety Precautions .......................................................................... 2-1

2-5 General Safety Precautions ............................................................................ 2-2

2-6 System Safety ................................................................................................. 2-3

Chapter 3 Chassis Components

3-1 Overview ......................................................................................................... 3-1

3-2 Components .................................................................................................... 3-1

Chassis ............................................................................................................ 3-1

Fans ................................................................................................................3-1

Blower .............................................................................................................3-1

Mounting Rails ................................................................................................ 3-1

Power Supply .................................................................................................. 3-2

Air Shroud ....................................................................................................... 3-2

3-3 Where to get Replacement Components ........................................................ 3-2

3-4 Chassis Model Options ................................................................................... 3-2

Identifying Fan and Blower-Cooled Chassis Models ...................................... 3-2

Model SC512 .................................................................................................. 3-4

Model SC512C ................................................................................................ 3-4

Model SC512F ................................................................................................ 3-5

Model SC512L ................................................................................................. 3-7

SC512 Chassis Manual

vi

Chapter 4 System Interface

4-1 Overview ......................................................................................................... 4-1

4-2 Control Panel Buttons ..................................................................................... 4-2

4-3 Control Panel LEDs ........................................................................................ 4-2

Chapter 5 Chassis Setup and Maintenance

5-1 Overview ......................................................................................................... 5-1

5-2 Installation Procedures .................................................................................... 5-1

General Maintenance ...................................................................................... 5-1

5-3 Removing the Chassis Cover ......................................................................... 5-2

5-4 Installing Hard Drives ...................................................................................... 5-3

5-5 Installing the Motherboard .............................................................................. 5-5

Important Motherboard Installation Information .............................................. 5-5

Standoffs ......................................................................................................... 5-6

5-6 Installing the DVD or CD-ROM Drive ............................................................. 5-7

Add-on Card/Expansion Slot Setup ................................................................ 5-8

5-7 Installing the Air Shroud .................................................................................. 5-9

Installation Complete ..................................................................................... 5-10

5-8 System Fans ..................................................................................................5-11

System Fan Tray ............................................................................................5-11

System Fan Tray Replacement..................................................................... 5-12

5-9 Power Supply ............................................................................................... 5-13

Power Supply Failure .................................................................................... 5-13

Replacing the Chassis LED Panel ................................................................ 5-15

Chapter 6 Rack Installation

6-1 Overview ......................................................................................................... 6-1

6-2 Unpacking the System .................................................................................... 6-1

6-3 Preparing for Setup ......................................................................................... 6-1

Choosing a Setup Location ............................................................................. 6-1

Rack Precautions ............................................................................................ 6-2

General Server Precautions ............................................................................ 6-2

Rack Mounting Considerations ....................................................................... 6-3

Ambient Operating Temperature ................................................................ 6-3

Reduced Airow ......................................................................................... 6-3

Mechanical Loading ................................................................................... 6-3

Circuit Overloading ..................................................................................... 6-3

Reliable Ground ......................................................................................... 6-3

6-4 Rack Mounting Instructions ............................................................................. 6-4

Identifying the Sections of the Rack Rails (Optional Item) ............................. 6-4

vii

Preface

Installing the Inner Rail Extension .................................................................. 6-5

Installing the Outer Rails to the Rack ............................................................. 6-6

Installing the Chassis into a Rack................................................................... 6-8

Mid-Mount Telco Rack..................................................................................... 6-9

Installing the Chassis into a Rack in Mid-Mount Position .............................. 6-9

Appendix A Cables, Screws, and Other Accessories

Appendix B Power Supply Specications

SC512 Chassis Manual

viii

Notes

Chapter 1

Introduction

1-1 Overview

Supermicro’s SC512 1U chassis features a unique and highly-optimized design.

The chassis is equipped with a high efciency power supply in a small form factor

for optimized space efciency.

1-2 Shipping List

Part Numbers

Please visit the following link for the latest shiping lists and part numbers for your par-

ticular chassis model http://www.supermicro.com/products/chassis/1U/?chs=512

Chapter 1: Introduction

1-1

SC512 Chassis

Model CPU HDD I/O Slots

Power

Supply

SC512-200B

UP 1x Fixed FH

200W

(High Efciency)

SC512C-200(B)

UP 1x Fixed FH 200W

SC512C-260(B)

UP 1x Fixed FH 260W

SC512F-520(B)

DP/UP 1x Fixed FH 520W

SC512F-520L(B)

DP/UP 1x Fixed FH 520W

SC512F-260(B)

UP 1x Fixed FH 260W

SC512F-280(B)

DP/UP 2x Fixed FH 280W

SC512L-200(B)

UP 2x Fixed FH 200W

SC512L-260(B)

UP 2x Fixed FH 260W

SC512L-260(B)-LCD

UP 1x Fixed FH 260W

SC512 Chassis Manual

1-2

1-3 Chassis Features

The SC512 1U high-performance chassis supports a wide range of features. See

the Chassis Components section of this manual for a list of featues included in

each of the SC512 models.

CPU

The SC512 chassis supports a DP Xeon, Pentium D or UP P3/P4 processor.

Please refer to the motherboard specications pages on our web site for updates

on supported processors.

I/O Expansion slots

Each version of the SC512 chassis includes one full I/O expansion slot

Peripheral Drives

Some SC512 chassis support peripheral dives such as a DVD-ROM, CD-ROM or

oppy disk drive. These drives allows you to quickly install or save data.

Dual Hard Drives

Some SC512 chassis models support a second hard disk drive. For more details,

check the Chassis Components section of this manual or the Supermicro website

at www.supermicro.com.

1-3

Chapter 1 Introduction

1-4 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Asia-Pacic

Address: Super Micro Computer, Inc.

4F, No. 232-1, Liancheng Rd.

Chung-Ho 235, Taipei County

Taiwan, R.O.C.

Tel: [phone]

Fax: [phone]

Web Site: www.supermicro.com.tw

Technical Support:

Email: [e-mail]

Tel: [phone]

SC512 Chassis Manual

1-4

1-5 Returning Merchandise for Service

A receipt or copy of your invoice marked with the date of purchase is required be-

fore any warranty service will be rendered. You can obtain service by calling your

vendor for a Returned Merchandise Authorization (RMA) number. When returning

to the manufacturer, the RMA number should be prominently displayed on the

outside of the shipping carton, and mailed prepaid or hand-carried. Shipping and

handling charges will be applied for all orders that must be mailed when service

is complete.

For faster service, RMA authorizations may be requested online (http://www.

supermicro.com/support/rma/).

Whenever possible, repack the chassis in the original Supermicro carton, using the

original packaging material. If these are no longer available, be sure to pack the

chassis securely, using packaging material to surround the chassis so that it does

not shift within the carton and become damaged during shipping.

This warranty only covers normal consumer use and does not cover damages in-

curred in shipping or from failure due to the alteration, misuse, abuse or improper

maintenance of products.

During the warranty period, contact your distributor rst for any product problems.

2-1

Chapter 2: System Safety

Chapter 2

System Safety

2-1 Overview

This chapter provides a quick setup checklist to get your chassis up and running.

Following the steps in order given should enable you to have your chassis setup and

operational within a minimal amount of time. This quick setup assumes that you are

an experienced technician, famailiar with common concepts and terminology.

2-2 Warnings and Precautions

You should inspect the box the chassis was shipped in and note if it was damaged

in any way. If the chassis itself shows damage, le a damage claim with carrier

who delivered your system.

Decide on a suitable location for the rack unit that will hold that chassis. It should

be situated in a clean, dust-free area that is well venilated. Avoid areas where heat,

electrical noise and eletromagnetic elds are generated.

You will also need it placed near at least one grounded power outlet. When cong-

ured, the SC512 chassis includes one power supply.

2-3 Preparing for Setup

The SC512 chassis includes a set of rail assemblies, including mounting brackets

and mounting screws you will need to install the systems into the rack. Please read

this manual in its entirety before you begin the installation procedure.

2-4 Electrical Safety Precautions

Basic electrical safety precautions should be followed to protect yourself from harm

and the SC512 from damage:

Be aware of the locations of the power on/off switch on the chassis as well •

as the room’s emergency power-off switch, disconnection switch or electrical

outlet. If an electrical accident occurs, you can then quickly remove power from

the system.

SC512F Chassis Manual

2-2

Do not work alone when working with high voltage components.•

Power should always be disconnected from the system when removing or in-•

stalling main system components, such as the serverboard, memory modules

and the DVD-ROM and oppy drives (not necessary for hot swappable drives).

When disconnecting power, you should rst power down the system with the

operating system and then unplug the power cords from all the power supply

modules in the system.

When working around exposed electrical circuits, another person who is fa-•

miliar with the power-off controls should be nearby to switch off the power, if

necessary.

Use only one hand when working with powered-on electrical equipment. This •

is to avoid making a complete circuit, which will cause electrical shock. Use

extreme caution when using metal tools, which can easily damage any electrical

components or circuit boards they come into contact with.

Do not use mats designed to decrease electrostatic discharge as protection from •

electrical shock. Instead, use rubber mats that have been specically designed

as electrical insulators.

The power supply power cord must include a grounding plug and must be •

plugged into grounded electrical outlets.

Serverboard battery: CAUTION - There is a danger of explosion if the onboard •

battery is installed upside down, which will reverse its polarities This battery

must be replaced only with the same or an equivalent type recommended by

the manufacturer. Dispose of used batteries according to the manufacturer’s

instructions.

DVD-ROM laser: CAUTION - this server may have come equipped with a •

DVD-ROM drive. To prevent direct exposure to the laser beam and hazardous

radiation exposure, do not open the enclosure or use the unit in any uncon-

ventional way.

2-3

Chapter 2: System Safety

2-5 General Safety Precautions

Keep the area around the chassis clean and free of clutter.•

Place the chassis top cover and any system components that have been re-•

moved away from the system or on a table so that they won’t accidentally be

stepped on.

While working on the system, do not wear loose clothing such as neckties and •

unbuttoned shirt sleeves, which can come into contact with electrical circuits or

be pulled into a cooling fan.

Remove any jewelry or metal objects from your body, which are excellent metal •

conductors that can create short circuits and harm you if they come into contact

with printed circuit boards or areas where power is present.

After accessing the inside of the system, close the system back up and secure •

it to the rack unit with the retention screws after ensuring that all connections

have been made.

2-6 System Safety

Electrostatic discharge (ESD) is generated by two objects with different electrical

charges coming into contact with each other. An electrical discharge is created to

neutralize this difference, which can damage electronic components and printed

circuit boards. The following measures are generally sufcient to neutralize this

difference before contact is made to protect your equipment from ESD:

Do not use mats designed to decrease electrostatic discharge as protection from •

electrical shock. Instead, use rubber mats that have been specically designed

as electrical insulators.

Use a grounded wrist strap designed to prevent static discharge.•

Keep all components and printed circuit boards (PCBs) in their antistatic bags •

until ready for use.

Touch a grounded metal object before removing any board from its antistatic •

bag.

SC512F Chassis Manual

2-4

Do not let components or PCBs come into contact with your clothing, which may •

retain a charge even if you are wearing a wrist strap.

Handle a board by its edges only; do not touch its components, peripheral chips, •

memory modules or contacts.

When handling chips or modules, avoid touching their pins.•

Put the serverboard and peripherals back into their antistatic bags when not •

in use.

For grounding purposes, make sure your computer chassis provides excellent •

conductivity between the power supply, the case, the mounting fasteners and

the serverboard.

3-1

Chapter 3: Chassis Components

Chapter 3

Chassis Components

3-1 Overview

This chapter describes the most common components included with your chassis.

Some components listed may not be included or compatible with your particular

chassis model. For more information, see the installation instructions detailed later

in this manual.

3-2 Components

Chassis

Depending on the model, the SC512 chassis may include one slim DVD-ROM/CD-

ROM bay, at least one xed hard drive, a oppy drive, and/or two USB ports. For

the latest shipping lists, visit our Web site at: http://www.supermicro.com.

Fans

The SC512 model chassis accepts two or three system fans powered by the moth-

erboard. These fans are 1U high and are powered by 3-pin connectors.

Blower

The SC512, SC512L and SC512C model chassis use a single blower unit for

system cooling.

Mounting Rails

The SC512 can be placed in a rack for secure storage and use. To set up your

rack, follow the step-by-step instructions included in this manual. SC512 models

with narrow chassis designs include specialized rails for mounting in a standard

rack. See the Rack Installation section of this manual for details.

SC512 Chassis Manual

3-2

Power Supply

Each SC512 chassis model includes a high-efciency power supply rated at 200,

260, 280, 410 or 580 Watts. In the unlikely event your power supply fails, replace-

ment is simple and can be done without tools.

Air Shroud

Air shrouds are shields, usually plastic, that funnel air directly to where it is needed.

Always use the air shroud included with your chassis.

3-3 Where to get Replacement Components

Though not frequently, you may need replacement parts for your system. To en-

sure the highest level of professional service and technical support, we strongly

recommend purchasing exclusively from our Supermicro Authorized Distributors /

System Integrators / Resellers. A list of Supermicro Authorized Distributors / System

Integrators /Reseller can be found at: http://www.supermicro.com. Click the Where

to Buy link.

3-4 Chassis Model Options

The following section lists the different options which are available for each of the

different chassis models in the SC512 chassis family of products.

Identifying Fan and Blower-Cooled Chassis Models

Your SC512 chassis is equipped with either a blower unit or a set of system fans

for optimized chassis cooling.

The SC512, SC512C and most SC512L model chassis use a blower unit for chas-

sis cooling.

The SC512F model chassis are cooled with system fans. The number of system

fans included in your specic system may vary.

See the following page for illustrations of blower units and system fans. For detailed

instructions on replacing a blower unit or system fans, see the Chassis Setup and

Maintenance section of this manual.

3-3

Chapter 3: Chassis Components

Figure 3-1: Blower-Cooled Chassis Model

Air blower unit

included in chassis

models SC512,

SC512C and SC512L

Figure 3-2: Fan-Cooled Chassis Model

System fans included

in chassis model

SC512F

SC512 Chassis Manual

3-4

Model SC512

Includes a slot with a dummy cover plate where an optional CD-ROM drive may be

installed, and a 200 Watt power supply. The SC512 model chassis is cooled with

an internal blower unit.

Figure 3-3: Chassis Model SC512

Dummy Cover

Plate for Optional

CD-ROM Drive

Model SC512C

Includes a CD-ROM drive, oppy drive, USB ports and a 200 or 260 Watt power

supply. The SC512C model chassis is cooled with an internal blower unit.

Figure 3-4: Chassis Model SC512C

Floppy Drive

CD-ROM Drive

USB Ports

SC512-200

Chassis Blower/Fan DVD/CD Floppy USB HDD Power Supply

Standard Blower Optional CD - - 1x 3.5" 200 Watt

SC512C

Chassis Blower/

Fan

DVD/CD Floppy USB HDD Power Sup-

ply

Standard Blower 1x CD 1x Floppy 1x USB 1x 3.5" 200 Watt

SC512C-260

Chassis Blower/

Fan

DVD/CD Floppy USB HDD Power Sup-

ply

Standard Blower 1x CD 1x Floppy 1x USB 1x 3.5" 260 Watt

3-5

Chapter 3: Chassis Components

Model SC512F

The SC512F models may include a DVD-ROM or CD-ROM drive, USB ports and a

260, 280, 410 or 520 Watt power supply. The SC512F-520L model can support a

second optional hard disk drive. The SC512F-200 and SC512F-260 have a narrow

chassis design, yet mount in a standard rack by utilizing special mounting rails. See

the Rack Installation section of theis manual for details. All SC512F model chassis

are cooled with system fans.

Figure 3-5: Chassis Model SC512F-260

CD-ROM Drive

SC512F-260

Chassis Blower/Fan DVD/CD Floppy USB HDD Power Supply

Narrow* Fan 1x CD - - 1x 3.5" 260 Watt

* Note: Narrow chassis models include specialized mounting rails to t into a stan-

dard rack. See the Rack Installation section of this manual for details.

DVD-ROM Drive

Figure 3-6: Chassis Model SC512F-280

SC512F-280

Chassis Blower/Fan DVD/CD Floppy USB HDD Power Supply

Standard Fan 1x DVD - - 1x 3.5" 280 Watt

SC512 Chassis Manual

3-6

Figure 3-8: Chassis Model SC512F-520

Standard Chassis, System Fans, DVD-ROM, USB Ports, 520W Power Supply

Figure 3-7: Chassis Model SC512F-410

Standard Chassis, System Fans, DVD-ROM, USB Ports, 520W Power Supply

USB Ports

USB Ports

Figure 3-9: Chassis Model SC512F-520L

DVD-ROM Drive

DVD-ROM Drive

SC512F-520

Chassis Blower/Fan DVD/CD Floppy USB HDD Power Supply

Standard Fan 1x DVD - USB 1x 3.5" 520 Watt

SC512F-410

Chassis Blower/Fan DVD/CD Floppy USB HDD Power Supply

Standard Fan 1x DVD - USB 1x 3.5" 520 Watt

SC512F-520L

Chassis Blower/Fan DVD/CD Floppy USB HDD Power Supply

Standard Fan - - - 1x or

optional

2x 3.5"

520 Watt

3-7

Chapter 3: Chassis Components

Model SC512L

The SC512L models include two 3.5" hard disk drives and a 200 or 260 Watt power

supply. The SC512L model chassis is cooled with an internal blower unit.

Figure 3-10: Chassis Model SC512L

SC512L

Chassis Blower/Fan DVD/CD Floppy USB HDD Power Supply

Standard Blower - - - 2x 3.5" 200 Watt

SC512L-260

Chassis Blower/Fan DVD/CD Floppy USB HDD Power Supply

Standard Blower - - - 2x 3.5" 260 Watt

Figure 3-11: Chassis Model SC512L-260

SC512L-260(B)-LCD

Chassis Blower/Fan DVD/CD Floppy USB HDD Power Supply

Standard Blower - - - 1x 3.5" 260 Watt

Figure 3-12: Chassis Model SC512L-260-LCD

SC512 Chassis Manual

3-8

Notes

4-1

Chapter 4: System Interface

Chapter 4

System Interface

4-1 Overview

There are several LEDs on the control panel and on the drive carriers to keep you

constantly informed of the overall status of the system, as well as the activity and

health of specic components. Most SC512 models are two buttons on the chassis

a control panel: a reset button and an on/off switch. This chapter explains the mean-

ings of all LED indicators and the appropriate response you may need to take.

Figure 4-1: Chassis LED and Buttons

SC512 Chassis Manual

4-2

4-2 Control Panel Buttons

There are two push-buttons located on the front of the chassis. These are a reset

button and a power on/off button.

 Reset: The reset button is used to reboot the system.

 Power: The main power switch is used to apply or remove power from the

power supply to the server system. Turning off system power with this button re-

moves the main power but keeps standby power supplied to the system. Therefore,

you must unplug system before servicing.

4-3 Control Panel LEDs

The control panel located on the front of the SC512 chassis has ve LEDs. These

LEDs provide you with critical information related to different parts of the system.

This section explains what each LED indicates when illuminated and any corrective

action you may need to take.

 Overheat/Fan Fail: When this LED ashes it indicates a fan failure. When

continuously on (not ashing) it indicates an overheat condition, which may be

caused by cables obstructing the airow in the system or the ambient room tem-

perature being too warm. Check the routing of the cables and make sure all fans

are present and operating normally. You should also check to make sure that the

chassis covers are installed. Finally, verify that the heatsinks are installed properly.

This LED will remain ashing or on as long as the overheat condition exists.

4-3

Chapter 4: System Interface

 NIC2: Indicates network activity on GLAN2 when ashing.

 NIC1: Indicates network activity on GLAN1 when ashing.

 HDD: Indicates IDE channel activity. SAS/SATA drive, SCSI drive, and/or

DVD-ROM drive activity when ashing.

 Power: Indicates power is being supplied to the system's power supply units.

This LED should normally be illuminated when the system is operating.

SC512 Chassis Manual

4-4

Notes

5-1

Chapter 5: Chassis Setup and Maintenance

Chapter 5

Chassis Setup and Maintenance

5-1 Overview

This chapter covers the steps required to install components and perform mainte-

nance on the chassis. The only tool you will need to install components and perform

maintenance is a Phillips head and a athead screwdriver. Print this page to use

as a reference while setting up your chassis.

5-2 Installation Procedures

Removing the Chassis Cover

Installing the Hard Drive

Installing the Motherboard (includes I/O Shield and Expansion Card Slot setup)

Installing the DVD or CD-ROM Drive

Installing the Air Shroud

General Maintenance

Systems Fans

Power Supply

Review the warnings and precautions listed in the manual be­fore setting up or servicing this chassis. These include infor­mation in Chapter 2: System Safety and the warning/precau­tions listed in the setup instructions.

!

Certain motherboards and heatsinks may not be compatible
with this chassis. Before installation, review the motherboard
installation procedures in this chapter.

!

SC512 Chassis Manual

5-2

5-3 Removing the Chassis Cover

Removing the Chassis Cover

Remove the screws holding the chassis cover in place.1.

Apply pressure to the middle front of the chassis cover.2.

Slide the cover toward the rear of the chassis.3.

Figure 5-1: Removing the Chassis Cover

Warning: Except for short periods of time, do NOT operate the
server without the cover in place. The chassis cover must be in

place to allow proper airow and prevent overheating.

!

Remove these screws

Remove this screw

Remove these screws

Flat head

6-32 x 5 mm

[0.197]

HARD DRIVE

5-3

Chapter 5: Chassis Setup and Maintenance

5-4 Installing Hard Drives

Installing a Hard Drive

Before adding a hard drive, you must remove the DVD-ROM/CD-ROM drive.

1. Open the chassis cover.

2. If you have not already done so, remove the fan tray. For more information

on removing the fan tray, see the Maintenance section located at the end of this

chapter.

3. Remove the CD-ROM drive. To do this, remove the two screws holding the drive

in place. One screw is external. The other is internal.

Figure 5-2: Removing the CD-ROM Drive to Access the Hard Drive

Remove these screws

DVD-ROM/CD-ROM

Drive

Flat head

6-32 x 5 mm

[0.197]

HARD DRIVE

SC512 Chassis Manual

5-4

Hard Drive

Hard Drive

Second Hard

Drive

Figure 5-3: Adding the Hard Drive

Figure 5-4: Adding a second Hard Drive

4. Place the hard drive in the chassis as illustrated. Make sure the hard drive con-

nectors face the inside of the chassis.

5. Secure the hard drive to the chassis using the four screws.

6. SC512F-280, SC512L and SC512L-260 model users: These chassis can support

a second hard drive. Insert the second hard drive at this time. If you are are not

using the models listed above, skip this step.

Flat head

6-32 x 5 mm

[0.197]

HARD DRIVE

Flat head

6-32 x 5 mm

[0.197]

HARD DRIVE

5-5

Chapter 5: Chassis Setup and Maintenance

Important Motherboard Installation Information

Before installing the motherboard, be aware of the following:

I/O Shield Backplate

The backplate holds the motherboard ports in place. Your motherboard must match

SC512 backplate. If your motherboard does not match, you must choose a different

motherboard.

Heatsinks

Some compatible motherboards require heatsinks to lower the temperature of the

components. Heatsinks for the SC512 chassis must be rated for 1U or less.

Figure 5-5: The SC512 Backplate (I/O Shield)

5-5 Installing the Motherboard

Flat head

6-32 x 5 mm

[0.197]

HARD DRIVE

SC512 Chassis Manual

5-6

Figure 5-6: Installing the Motherboard

Standoffs

Standoffs prevent short circuits by securing space between the motherboard and

the chassis surface. The SC512 chassis includes permanent standoffs in locations

used by most motherboards. These standoffs accept the rounded Phillips head

screws included in the SC512 accessories packaging.

Installing the Motherboard

Review the documentation that came with your motherboard. Become familiar 1.

with component placement, requirements, precautions, and cable connec-

tions.

Open the chassis cover.2.

Align the motherboard with the chassis standoffs and carefully, place the 3.

motherboard in the chassis. Make sure rear ports line up with the I/O shield.

Secure the motherboard to the chassis using the ten rounded, Phillips head 4.

screws supplied with the accessories kit.

Secure the CPU(s), heatsinks, and other components to the motherboard as 5.

described in the motherboard documentation. Do not exceed eight pounds of

torque when tightening down the motherboard.

Connect the cables between the motherboard, backplane, chassis, front 6.

panel, and power supply, as needed.

Round head

3 x 5 mm

[0.197]

Flat head

6-32 x 5 mm

[0.197]

HARD DRIVE

Round head

2.6 x 5 mm
[0.197]

5-7

Chapter 5: Chassis Setup and Maintenance

5-6 Installing the DVD or CD-ROM Drive

Replacing the DVD or CD-ROM

1. Place the DVD-ROM or CD-ROM drive in the chassis above the hard drive.

2. Secure the drive with two screws. One screw is external. The other screw is

internal.

Figure 5-7: Replace the DVD-ROM/CD-ROM Drive

Replace these screws

DVD-ROM/CD-ROM

Drive

Hard Drive

Flat head

6-32 x 5 mm

[0.197]

HARD DRIVE

SC512 Chassis Manual

5-8

Add-on Card/Expansion Slot Setup

SC512 chassis includes a slot for one full height/full length add-on card and a riser

card. The riser card allows the add-on to t within the small 1U form.

The add-on card slot does not require a screw to hold the card in place.

Figure 5-8: Installing the Expansion Card

Installing Add-on and Expansion Cards

1. Disconnect the power supply, lay the chassis on a at surface, and open the

chassis cover.

2. Slide the add-on card clip upward.

3. Slide the add-on card slot shield toward the side of the chassis and remove the

Shield.

4. Secure the riser card to the motherboard.

5. Slide the add-on card (with "L" bracket) into the add-on card slot and the riser

card.

6. Replace the add-on card slot clip to secure the add-on card.

Add-on Card Slot Latch

Add-on Card

Slot Shield

5-9

Chapter 5: Chassis Setup and Maintenance

5-7 Installing the Air Shroud

Figure 5-10: Installing the Air Shroud in the SC512 Chassis

Installing The Air Shroud

1. Conrm that the air shroud matches your chassis model.

2. Place the air shroud in the chassis. The shroud sets directly behind the system

fans. If necessary, remove some perforated tabs to ensure a snug t.

Perforated Tabs

The air shroud helps cool the chassis by directing heated air through the rear of

the chassis. When installing the air fan, be aware of the following:

The air shroud is designed to t within the chassis. The sides of the air •

shroud should remain straight in relation to the top. Do not fold or bend the

air shroud.

The air shroud has perforated tabs that can be removed if motherboard com-•

ponents prevent proper air shroud installation. Do not remove a tab unless it

is necessary.

Figure 5-9: Air Shroud Placement

Incorrect Incorrect Correct

SC512 Chassis Manual

5-10

Checking the Airow in the Chassis

1. Make sure there are no objects to obstruct airow in and out of the server.

2. Do not operate the server without drives or drive trays in the drive bays. Use

only recommended server parts.

3. Make sure no wires or foreign objects obstruct air ow through the chassis. Pull

all excess cabling out of the airow path or use shorter cables.

The control panel LEDs inform you of system status. See “Chapter 3: System

Interface” for details on the LEDs and the control panel buttons.

Installation Complete

In most cases, the chassis power supply and fans are pre-installed. If you need to

install fans continue to the Systems Fan section of this chapter. If the chassis will be

installed into a rack, continue to the next chapter for rack installation instructions.

5-11

Chapter 5: Chassis Setup and Maintenance

Three heavy duty fans provide cooling for the chassis. These fans circulate air

through the chassis as a means of lowering the chassis internal temperature.

The SC512F-280 chassis accepts two fans instead of three.

5-8 System Fans

System Fan Tray

Systems fan trays are components that house groups of fans. The system fan tray

is held in place by two rivets permanently attached to the chassis surface. Each

rivet is encircled by a rubber mounting to reduce vibration.

Figure 5-11: Placing the System Fan

Fan Tray Support Pin

System Fan Tray

Rubber Grommet

SC512 Chassis Manual

5-12

System Fan Tray Replacement

Installing the System Fan Tray

Power down the system.1.

Disconnect each fan from the motherboard.2.

Lift the system fan tray and fans from the chassis. Retain the rubber mount-3.

ings that encircle the tray rivets.

Place the fans into the new system fan tray. Make all the fans face the correct 4.

direction.

Conrm the the rubber mountings are in place around the chassis rivets.5.

Align the fan tray with rivets and place the new fan tray (and system fans) 6.

into the chassis.

Reconnect the system fans to the motherboard7.

Replacing Individual System Fans

Fans can be replaced individually without removing the system fan tray. There is

no need to power down the system when replacing a system fan.

Replacing System Fans

If necessary, open the chassis while the power is running to determine which 1.

fan has failed. (Never run the server for an extended period of time with the

chassis open.)

Remove the failed fan's power cord from the serverboard.2.

Lift the failed fan completely from the chassis.3.

Place the new fan into the vacant space. Make sure the arrows on the top of 4.

the fan (indicating air direction) point in the same direction as the arrows on

the other fan(s).

Conrm that the fan is working properly and replace the chassis cover..5.

5-13

Chapter 5: Chassis Setup and Maintenance

Depending on your chassis model the SC512 chassis has a 200, 269, 280, 410 or

520 Watt power supply. This power supply is auto-switching capable. This enables

it to automatically sense and operate at a 100v to 240v input voltage. An amber

light will be illuminated on the power supply when the power is off. An illuminated

green light indicates that the power supply is operating.

Power Supply Failure

The SC512 series chassis has one power supply. In the unlikely event that the power

supply unit fails, the system will shut down and you will need to replace it.

Replacement units can be ordered directly from Supermicro (see contact information

in the preface) or an authorized reseller.

5-9 Power Supply

SC512 Chassis Manual

5-14

Remove this screw

Pan Head

6-32 x 5mm

[0.197]

Power Supply

Remove these screws

Replacing the Power Supply

Disconnect the power cord from the from the chassis to ensure that the unit is 1.

not accidentally plugged in.

Place the chassis on a stable hard surface and remove the chassis cover.2.

Disconnect the power supply from the motherboard and other chassis compo-3.

nents.

Remove the screws securing the power supply. Two screws are in the back 4.

of the chassis and one underneath. Retain the screws and the internal brace

that connects the power supply to the chassis from underneath.

Pull the power supply out of the chassis. 5.

Place the new power supply into the chassis and secure the power supply 6.

using the three screws and internal brace.

Connect the power supply to the motherboard and other chassis components.7.

Connect the power cord to the power supply and power up the chassis/server.8.

Once you conrm that the power supply has been installed correctly, replace 9.

the chassis cover.

Figure 5-12: Removing the Power Supply

M/B

HARD DRIVE

5-15

Chapter 5: Chassis Setup and Maintenance

Replacing the Chassis LED Panel

In the unlikely event that the chassis LED and buttons fail, you can replace the panel.

Replacement parts can be ordered from Super Micro or an authorized reseller.

Replacing the Chassis LED Panel

Power down and unplug the system.1.

Remove the chassis cover.2.

Disconnect the cord to the front panel.3.

Locate and remove three screws holding the panel in place. (If your chassis 4.

supports dual hard drives, you may have to remove the second hard drive

from the chassis).

Install the new LED panel and secure the unit with three screws.5.

Re-connect the cables to the LED panel and if necessary, replace the hard 6.

drive.

Figure 5-13: Replacing the LED Panel

SC512 Chassis Manual

5-16

Notes

6-1

Chapter 6: Rack Installation

Chapter 6

Rack Installation

6-1 Overview

This chapter provides a quick setup checklist to get your chassis up and running.

Following these steps in the order given should enable you to have the system

operational within a minimum amount of time.

6-2 Unpacking the System

You should inspect the box the chassis was shipped in and note if it was damaged

in any way. If the chassis itself shows damage you should le a damage claim with

the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold your chassis. It should

be situated in a clean, dust-free area that is well ventilated. Avoid areas where

heat, electrical noise and electromagnetic elds are generated. You will also need

it placed near a grounded power outlet. Be sure to read the Rack and Server Pre-

cautions in the next section.

6-3 Preparing for Setup

The box your chassis was shipped in should include two sets of rail assemblies,

two rail mounting brackets and the mounting screws you will need to install the

system into the rack. Please read this section in its entirety before you begin the

installation procedure outlined in the sections that follow.

Choosing a Setup Location

Leave enough clearance in front of the rack to enable you to open the front •

door completely (~25 inches).

Leave approximately 30 inches of clearance in the back of the rack to allow for •

sufcient airow and ease in servicing.

This product is for installation only in a Restricted Access Location (dedicated •

equipment rooms, service closets and the like).

SC512 Chassis Manual

6-2

Rack Precautions

Ensure that the leveling jacks on the bottom of the rack are fully extended to •

the oor with the full weight of the rack resting on them.

In single rack installation, stabilizers should be attached to the rack.•

In multiple rack installations, the racks should be coupled together.•

Always make sure the rack is stable before extending a component from the •

rack.

You should extend only one component at a time - extending two or more si-•

multaneously may cause the rack to become unstable.

General Server Precautions

Review the electrical and general safety precautions that came with the com-•

ponents you are adding to your chassis.

Determine the placement of each component in the rack • before you install the

rails.

Install the heaviest server components on the bottom of the rack rst, and then •

work up.

Use a regulating uninterruptible power supply (UPS) to protect the server from •

power surges, voltage spikes and to keep your system operating in case of a

power failure.

Allow the hot plug hard drives and power supply modules to cool before touch-•

ing them.

Warnings and Precautions!

!

!

6-3

Chapter 6: Rack Installation

Always keep the rack's front door and all panels and components on the servers •

closed when not servicing to maintain proper cooling.

Rack Mounting Considerations

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating tempera-

ture of the rack environment may be greater than the ambient temperature of the

room. Therefore, consideration should be given to installing the equipment in an

environment compatible with the manufacturer’s maximum rated ambient tempera-

ture (Tmra).

Reduced Airow

Equipment should be mounted into a rack so that the amount of airow required

for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition does not

arise due to uneven mechanical loading.

Circuit Overloading

Consideration should be given to the connection of the equipment to the power

supply circuitry and the effect that any possible overloading of circuits might have

on overcurrent protection and power supply wiring. Appropriate consideration of

equipment nameplate ratings should be used when addressing this concern.

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack itself

should be grounded. Particular attention should be given to power supply connec-

tions other than the direct connections to the branch circuit (i.e. the use of power

strips, etc.).

SC512 Chassis Manual

6-4

6-4 Rack Mounting Instructions

This section provides information on installing the SC512 chassis into a rack unit

with the rails provided. There are a variety of rack units on the market, which

may mean the assembly procedure will differ slightly. You should also refer to the

installation instructions that came with the rack unit you are using. The rails provided

with the SC512 chassis will t a rack between 28.5" and 33.25" deep.

NOTE: The SC512F-280 and SC512F-520 chassis models are designed with a

narrower chassis. Specialized rails are included to mount the chassis to a standard

rack.

Identifying the Sections of the Rack Rails (Optional Item)

The chassis package includes two rack rail assemblies in the rack mounting kit.

Each assembly consists of two sections: an inner xed chassis rail that secures

directly to the server chassis, and an outer xed rack rail that secures directly to

the rack itself.

The SC512F comes with "chassis ears" that allow the chassis to use generic

rails.

Outer Rails

Figure 6-1: Identifying the Sections of the Rack Rails

(Right side rail shown)

Inner Rails

Chassis Ears

6-5

Chapter 6: Rack Installation

Installing the Inner Rails

Place the inner rail on the side of the chassis aligning the hooks of the chas-1.

sis with the rail holes.

Slide the rail toward the front of the chassis to secure the rail in place.2.

Secure the chassis with four screws.3.

Repeat steps 1-3 for the other inner rail extension.4.

Installing the Inner Rail Extension

The SC512F includes chassis ears that you must remove before installing the

rails.

Removing the Chassis Ears

Locate and remove the three screws holding the chassis ear in place.1.

Repeat step on with the other chassis ear.2.

Figure 6-2: Installing Inner Rails to the Chassis

Flat head

M4 x 4 mm

[0.157]

RAIL

Round head

M4 x 4 mm

[0.157]

Flat head

M5 x 12 mm [0.472]

DVD-ROM CD-ROM FLOPPY DRIVE

Flat head

6-32 x 5 mm

[0.197]

Pan head

6-32 x 5 mm

[0.197]

Round head

3 x 5 mm

[0.197]

Pan head

6-32 x 5 mm

[0.197]

M/B

Flat head

6-32 x 5 mm

[0.197]

HARD DRIVE

Round head

2.6 x 5 mm
[0.197]

SC512 Chassis Manual

6-6

Installing the Outer Rails to the Rack

Installing the Outer Rails

Attach the short bracket to the outside of the long bracket. You must align the 1.

pins with the slides. Also, both bracket ends must face the same direction.

Adjust both the short and long brackets to the proper distance so that the rail 2.

ts snugly into the rack.

Secure the long bracket to the front side of the outer rail with two M5 screws 3.

and the short bracket to the rear side of the outer rail with three M5 screws.

Use a washer with each screw.

Repeat steps 1-4 for the left outer rail.4.

Secure to the

Front of the Rack

Secure to the

Rear of the Rack

Figure 6-3: Assembling the Outer Rails

Attach Outer Racks

together

Flat head

M5 x 12 mm [0.472]

Washer for M5

Flat head

6-32 x 5 mm

[0.197]

Round head

2.6 x 5 mm
[0.197]

6-7

Chapter 6: Rack Installation

Figure 6-4: Installing the Outer Rails to the Server Rack

3

3

2

SC512 Chassis Manual

6-8

Figure 6-5: Installing the Chassis into a Rack

Installing the Chassis into a Rack

Installing the Chassis

Conrm that the inner rails are attached to the chassis. Also, conrm that the 1.

outer rails are installed on the rack.

Align chassis rails with the front of the rack rails.2.

Slide the chassis rails into the rack rails, keeping the pressure even on both 3.

sides (you may have to depress the locking tabs when inserting). When the

server has been pushed completely into the rack, you should hear the locking

tabs "click" into the locked position.

(Optional) Insert and tightening the thumbscrews that hold the front of the 4.

server to the rack.

6-9

Chapter 6: Rack Installation

Mid-Mount Telco Rack

The SC512.supports Telco rack installation. The SC512 chassis compact design

allows the chassis to be installed into a Telco rack without the use of rails.

Installing the Chassis into a Rack in Mid-Mount Position

Instaling into a Mid-Mount Position Rack

If it is necessary to install the chassis in a mid-mount Telco rack, remove the 1.

chassis rails and the chassis ears (if the ears are installed at the front of the

chassis).

Locate the three screw holes in the middle of the chassis and secure the ears 2.

to the chassis with three at head screws. Make sure the screws are secure,

but do not over tighten the screws.

Figure 6-6: Moving the Chassis Ears for Telco Rack Installation

Flat head

M4 x 4 mm

[0.157]

RAIL

Round head

M4 x 4 mm

[0.157]

Flat head

M5 x 12 mm [0.472]

DVD-ROM CD-ROM FLOPPY DRIVE

Flat head

6-32 x 5 mm

[0.197]

Pan head

6-32 x 5 mm

[0.197]

Round head

3 x 5 mm

[0.197]

Pan head

6-32 x 5 mm

[0.197]

M/B

Flat head

6-32 x 5 mm

[0.197]

HARD DRIVE

Round head

2.6 x 5 mm
[0.197]

Place chassis

ears here

SC512 Chassis Manual

6-10

Figure 6-7: Installing the Server into a Telco Rack

SCALE 1:2

SCALE 1:2

Hold the chassis in the telco rack and screw the chassis to the rack using the 3.

three screw holes located in the chassis ears.

The chassis is held in place by the chassis ears and does not slide in and out 4.

of place.

Flat head

M5 x 12 mm [0.472]

Washer for M5

Flat head

6-32 x 5 mm

[0.197]

Round head

2.6 x 5 mm
[0.197]

A-1

Appendix A: SC512 Chassis Cables

Appendix A

Cables, Screws,

and Other Accessories

A-1 Overview

This appendix lists supported cables for your chassis system. It only includes the

most commonly used components and congurations. For more compatible cables,

refer to the manufacturer of the motherboard you are using and our Web site at:

www.supermicro.com.

A-2 Cables Included with SC512 Chassis

SC512C-260

Part # Type Length Description

CBL-0049 Cable 9 cm 16 pin to 16 pin ribbon cable

SC512C

Part # Type Length Description

- - - -

SC512-200

Part # Type Length Description

CBL-0049L Cable Front cable 16 pin to 16 pin

CBL-0084L Wire 9 cm DVD Cable. Lead free.

CBL-0260L US Power Cord 18 AWG

CBL-0261L Cable 40cm 40cm 7-pin SATA Cable S-RA

CBL-0262L Cable

4-pin to 1x SATA (RA) + 1x 4-pin
(RA) + 1x FPD PWS

CBL-0263L Cable 77cm 9-pin to 9-pin Internal USB Cable

SC512 Chassis Manual

A-2

SC512F-280

Part # Type Length Description

CBL-0142L Cable 30 cm (~12")

Seven pin SATA with two 90 degree
side connectors. Lead free.

CBL-0156L Cable 40 cm

16 pin to 16 pin FP Cable. Lead
Free.

CBL-0084L Wire 9 cm DVD Cable. Lead free.

- Cable 6' Regional power cord

SC512F-520L

Part # Type Length Description

CBL-0142L Cable 30 cm (~12")

Seven pin SATA with two 90 degree
side connectors. Lead free.

CBL-0156L Cable 40 cm

16 pin to 16 pin FP Cable. Lead
Free.

- Cable 6' Regional power cord

SC512F-520

Part # Type Length Description

CBL-0142L Cable 30 cm (~12")

Seven pin SATA with two 90 degree
side connectors. Lead free.

CBL-0156L Cable 40 cm

16 pin to 16 pin FP Cable. Lead
Free.

CBL-0084L Wire 9 cm DVD Cable. Lead free.

- Cable 6' Regional power cord

SC512L

Part # Type Length Description

- - - -

SC512F-410

Part # Type Length Description

CBL-0142L Cable 30 cm (~12")

Seven pin SATA with two 90 degree
side connectors. Lead free.

CBL-0156L Cable 40 cm

16 pin to 16 pin FP Cable. Lead
Free.

CBL-0084L Wire 9 cm DVD Cable. Lead free.

- Cable 6' Regional power cord

A-3

Appendix A: SC512 Chassis Cables

Extending Power Cables

Although Super Micro chassis are designed with to be efcient and cost-effective,

some compatible motherboards have power connectors located in different areas.

To use these motherboards you may have to extend the power cables to the mother

boards. To do this, use the following chart as a guide.

Power Cable Extenders

Number of Pins Cable Part # Length

24 pin CBL - 0042 7.9”(20 CM)

20 pin CBL - 0059 7.9”(20 CM)

8 pin CBL - 0062 7.9”(20 CM)

4 pin CBL - 0060 7.9”(20 CM)

Front Panel to the Motherboard

The SC512 chassis includes a cable to connect the chassis front panel to the

motherboard. If your motherboard uses a different connector, use the following list

to nd a compatible cable.

Front Panel to Motherboard Cable (Ribbon Cable)

Number of Pins

(Front Panel)

Number of Pins

(Motherboard)

Cable Part #

16 pin 16 pin CBL - 0049

16 pin 20 pin CBL - 0048

20 pin 20 pin CBL - 0047

16 pin various* CBL - 0068

20 pin various* CBL - 0067

* Split cables: Use these cable if your motherboard requires several different con-

nections from the front panel.

SC512L-260

Part # Type Length Description

CBL-0049 Cable 9 cm 16 pin to 16 pin ribbon cable

SC512L-260-LCD

Part # Type Length Description

CBL-0049 Cable 9 cm 16 pin to 16 pin ribbon cable

SC512 Chassis Manual

A-4

A-3 Routing the Chassis Cables

In order for the SC512 chassis to perform safely and efciently, it is important that the

cables are routed correctly. Follow the instructions below and review both the cabling

diagram and photograph to ensure that the cabling has been properly routed.

Preparing the Chassis for Cable Routing

Unplug the chassis from any power source.1.

Review the diagram on the following page, taking note of the naming of each 2.

cable.

Remove the screws securing the fan platform to the bottom of the chassis.3.

RIGHT MIDDLE BRACKET

MIDDLE BRACKET

FA N

PWR

SATA PWR

(RIGHT ANGLE)

SATA PWR

(RIGHT ANGLE)

S A TA

(STRAIGHT)

HDD

HDD

LEFT

S A TA

(RIGHT ANGLE)

MB SATA

PORTS

MOTHERBOARD

AREA

1

1

1A

1

2A

1

3A

1

4A

1

5A

1

3C

1

3B

1

2B

1

2C

1

1C

1B

Figure A-1: Chassis Cable Routing Diagram (SC512L-200/260)

A-5

Appendix A: SC512 Chassis Cables

Routing Cable (1A) from Hard Drive (1B)

Plug cable (1A) into the SATA port of hard drive (1B).1.

Lift up the fan and run cable (1A) straight out from the port and under the fan.2.

Route cable (1A) over the hard drive and through the left middle bracket.3.

Plug cable (1A) into upper SATA port (1C) on the motherboard.4.

Routing Cable (2A) from Hard Drive (2B)

Plug cable (2A) into the SATA port of hard drive (2B).1.

Run cable (2A) upwards at a right angle, up and over the top of hard drive 2.

(2B).

Route cable (2A) through the left middle bracket.3.

Plug cable (2A) into lower SATA port (2C) on the motherboard.4.

Routing Split Cable (3A)(4A) from Hard Drives (1B)(2B) to the Power Supply

Plug the end of the split cable (3A) into hard drive (2B).1.

Route the end of the split cable (3A) straight up at a right angle, beside the 2.

fan, and over the top of cable (1A).

Plug the end of the split cable (3A) into connector (3B).3.

Plug the other end of the split cable (4A) into hard drive (1B). 4.

Route the end of the split cable (4A) straight up at a right angle, along the top 5.

of the fan.

Route cable (5A) through the right middle bracket and plug it into connector 6.

(3B).

SC512 Chassis Manual

A-6

Figure A-2: Chassis Cable Routing

Checking the Cable Routing

Check the cable routing by following out each cable in the previous steps and 1.

comparing them to the diagram in Figure A-1, and the photograph in Figure

A-2.

A-7

Appendix A: SC512 Chassis Cables

A-4 Chassis Screws

The Chassis and accessory box include all the screws needed to setup your chassis.

This section include descriptions of the most common screws used. Your chassis

may not require all the parts listed.

Flat head

M4 x 4 mm

[0.157]

RAIL

Round head

M4 x 4 mm

[0.157]

Flat head

M5 x 12 mm [0.472]

Washer for M5

DVD-ROM CD-ROM FLOPPY DRIVE

Flat head

6-32 x 5 mm

[0.197]

Pan head

6-32 x 5 mm

[0.197]

Round head

3 x 5 mm

[0.197]

Pan head

6-32 x 5 mm

[0.197]

M/B

Flat head

6-32 x 5 mm

[0.197]

HARD DRIVE

Thumb screw

6-32 x 5 mm [0.197]

M/B standoff

6-32 to 6-32

M/B STANDOFF

M/B (CPU) standoff

M5 to 6-32

Round head

2.6 x 5 mm
[0.197]

Figure A-3: Chassis Screws

SC512 Chassis Manual

A-8

Notes

B-1

Appendix B: SC512F Power Supply Specications

Appendix B

Power Supply Specications

This appendix lists power supply specications for your chassis system.

SC512C Chassis Models

200 260

MFR Part # PWS-0043 PWS-0055

Rated AC Voltage

100 - 240V
60 - 50Hz
5-3 Amp

100 - 240V
60 - 50Hz
4 Amp Max

+5V standby 2.0 Amp 2.0 Amp

+12V 12.0 Amp 18.0 Amp

+5V 20 Amp 25.0 Amp

+3.3V 17.0 Amp 15.0 Amp

-12V 0.8 Amp 1.0 Amp

SC512 Chassis Model

200

MFR Part # PWS-201-1H

Rated AC Voltage

100 - 240V
50 - 60Hz
4-2 Amp Max

+5V standby 2.0 Amp

+12V 16.0 Amp

+5V 8.0 Amp

+3.3V 8.0 Amp

-12V 0.5 Amp

SC512 Chassis Manual

B-2

SC512F Chassis Models (See below for 410 model)

520/520L 260 280

MFR Part # PWS-581-1R PWS-0055 PWS-281-1H

Rated AC Voltage

100 - 240V
50 - 60Hz
7A-3A

100 - 240V
60 - 50Hz
4 Amp Max

100 - 240V
50 - 60Hz
5A MAX

+5V standby 3 Amp 2.0 Amp 2 Amp

+12V 39 Amp 18.0 Amp 23 Amp

+5V 20 Amp 25.0 Amp 18 Amp

+3.3V 16 Amp 15.0 Amp 15 Amp

-12V 0.5 Amp 1.0 Amp 1 Amp

SC512F-410 Chassis Model

200

MFR Part # PWS-0061

DC Voltage

Voltage Range = -36V to -72V
Nominal Voltage = -48V
Max Input Current = 18A @ -48V

DC Output 5V + 3.3V ≤ 180W

+5V 35.0 Amp

+5V standby 3.0 Amp

+12V 32.0 Amp

-12V 0.5 Amp

+3.3V 20.0 Amp

SC512L Chassis Models

200 260/260-LCD

MFR Part # PWS-0043 PWS-0055

Rated AC Voltage

100 - 240V
60 - 50Hz
5-3 Amp

100 - 240V
60 - 50Hz
4 Amp Max

+5V standby 2.0 Amp 2.0 Amp

+12V 12.0 Amp 18.0 Amp

+5V 20 Amp 25.0 Amp

+3.3V 17.0 Amp 15.0 Amp

-12V 0.8 Amp 1.0 Amp

B-3

Appendix B: SC512F Power Supply Specications

Notes

SC512 Chassis Manual

B-4

Disclaimer (cont.)
The products sold by Supermicro are not intended for and will not be used in life sup­port systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices,
aircraft/emergency communication devices or other critical systems whose failure to per-

form be reasonably expected to result in signicant injury or loss of life or catastrophic

property damage. Accordingly, Supermicro disclaims any and all liability, and should
buyer use or sell such products for use in such ultra-hazardous applications, it does so
entirely at its own risk. Furthermore, buyer agrees to fully indemnify, defend and hold
Supermicro harmless for and against any and all claims, demands, actions, litigation,
and proceedings of any kind arising out of or related to such ultra-hazardous use or
sale.