Supero SC113 Series, SC113TQ-R650UB, SC113TQ-700CB, SC113TQ-700UB, SC113TQ-R650CB User Manual

SC113 Chassis Series

SC113TQ-R650UB SC113TQ-700CB

SC113TQ-700UB SC113TQ-R650CB

SC113TQ-560UB

USER’S MANUAL

1.0a

SUPER

®

SC113 Chassis Manual

ii

Manual Revision 1.0a
Release Date: August 14, 2008

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software, if any,
and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or
reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.

Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.

Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2008 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

iii

Preface

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It

provides information for the installation and use of the SC113 1U chassis. Installa-

tion and maintenance should be performed by experienced technicians only.

Supermicro’s SC113 1U chassis features a unique and highly-optimized design.

The chassis is equipped with a 650W or 700W, advanced design, high-efficiency

>85%+ power supply for superb power savings. High performance fans provide

ample optimized cooling for and 8 hot-swappable 2.5" SAS/SATA drives offers

maximum storage capacity in a 1U form factor.

This manual lists compatible parts available when this document was published. Al-

ways refer to the our Web site for updates on supported parts and configurations.

SC113 Chassis Manual

iv

Manual Organization

Chapter 1 Introduction

The first chapter provides a checklist of the main components included with this

chassis and describes the main features of the SC113 chassis. This chapter also

includes contact information.

Chapter 2 System Safety

This chapter lists warnings, precautions, and system safety. You should thoroughly

familiarize yourself with this chapter for a general overview of safety precautions

that should be followed before installing and servicing this chassis.

Chapter 3 Chassis Components

Refer here for details on this chassis model including the fans, bays, airflow shields,

and other components.

Chapter 4 System Interface

This chapter provides details on the system interface, which includes the functions

and information of he control panel LEDs and other LEDs located throughout the

system.

Chapter 5 Chassis Setup and Maintenance

Refer to this chapter for detailed information on this chassis. You should follow the

procedures given in this chapter when installing, removing, or reconfiguring your

chassis.

Chapter 6 Rack Installation

This chapter covers detailed information on chassis rack installation. You should

follow the procedures given in this chapter when installing, removing or reconfiguring

your chassis into a rack environment.

Appendices

These appendices list compatible cables, power supply specifications, and compat

-

ible backplanes. Not all compatible backplanes are listed. Refer to our Web site for

the latest compatible backplane information at http://www.supermicro.com.

Appendix A Chassis Cables

Appendix B Power Supply Specifications

Appendix C SAS-113TQ Backplane Specifications

v

Preface

Table of Contents

Preface

About This Manual ........................................................................................................iii

Chapter 1 Introduction

1-1 Overview ......................................................................................................... 1-1

1-2 Shipping List .................................................................................................... 1-

1

1-3 Chassis Features ............................................................................................ 1-

2

CPU ................................................................................................................. 1-

2

Hard Drives ..................................................................................................... 1-2

I/O Expansion

Slots ........................................................................................ 1-2

Peripheral Drives ............................................................................................. 1-2

1-4 Contacting Supermicro .................................................................................... 1-

3

1-5 Returning Merchandise for Service ................................................................ 1-

4

Chapter 2 System Safety

2-1 Overview ......................................................................................................... 2-1

2-2 Warnings and Precautions .............................................................................. 2-

1

2-3 Preparing for Setup ......................................................................................... 2-1

2-4 Electrical Safety Precautions .......................................................................... 2-2

2-5 General Safety Precautions ............................................................................ 2-3

2-6 System Safety ................................................................................................. 2-3

Chapter 3 Chassis Components

3-1 Overview ......................................................................................................... 3-1

3-2 Components .................................................................................................... 3-1

Chassis ............................................................................................................ 3-

1

Backplane ........................................................................................................ 3-

1

Fans ................................................................................................................ 3-1

Mounting Rails ................................................................................................ 3-

1

Power Supply .................................................................................................. 3-2

Air Shroud ....................................................................................................... 3-

2

3-3 Where to get Replacement Components ........................................................ 3-2

Chapter 4 System Interface

4-1 Overview ......................................................................................................... 4-1

4-2 Control Panel Buttons ..................................................................................... 4-2

4-3 Control Panel LEDs ........................................................................................ 4-3

4-4 Drive Carrier LEDs .......................................................................................... 4-4

SAS/SATA Drives ............................................................................................ 4-

4

SC113 Chassis Manual

vi

4-5 Power Supply LEDs ........................................................................................ 4-5

All Other

Power Supplies ................................................................................ 4-6

Chapter 5 Chassis Setup and Maintenance

5-1 Overview ......................................................................................................... 5-1

5-2 Installation and Maintenance Procedures ....................................................... 5-1

Installation ....................................................................................................... 5-

1

General Maintenance ...................................................................................... 5-1

5-3 Removing the Chassis Cover and Front Bezel .............................................. 5-2

5-4 Installing Hard Drives ...................................................................................... 5-3

5-5 DVD-ROM Drive Installation ........................................................................... 5-5

5-6 Installing the Motherboard .............................................................................. 5-7

Permanent and Optional Standoffs ................................................................. 5-

7

Expansion Card Setup .................................................................................... 5-

9

5-7 Installing the Air Shroud .................................................................................5-11

Checking the Air

Flow ................................................................................... 5-12

5-8 System Fans ................................................................................................. 5-13

5-9 Power Supply ............................................................................................... 5-15

Power Supply Failure .................................................................................... 5-1

5

Chapter 6 Rack Installation

6-1 Overview ......................................................................................................... 6-1

6-2 Unpacking the System .................................................................................... 6-1

6-3 Preparing for Setup ......................................................................................... 6-1

Choosing a Setup Location ............................................................................. 6-

1

Rack Precautions ............................................................................................ 6-

2

General Server Precautions ............................................................................ 6-

2

Rack Mounting Considerations ....................................................................... 6-

3

Ambient Operating Temperature ................................................................ 6-

3

Reduced Airflow ......................................................................................... 6-

3

Mechanical Loading ................................................................................... 6-

3

Circuit Overloading ..................................................................................... 6-

3

Reliable Ground ......................................................................................... 6-

3

6-4 Rack Mounting Instructions ............................................................................. 6-4

Identifying the Sections of the Rack Rails ...................................................... 6-

4

Inner Rail Extension ........................................................................................ 6-5

Outer Rails ...................................................................................................... 6-

6

Installing the Chassis into a Telco rack .......................................................... 6-

9

Appendix A SC113 Chassis Cables

vii

Preface

Appendix B SC113 Power Supply Specifications

Appendix C BPN-SAS-113TQ Backplan

e

SC113 Chassis Manual

viii

Notes

Chapter 1

Introduction

1-1 Overview

Supermicro’s SC113 1U chassis features a unique and highly-optimized design. The

chassis is equipped with high efficiency power supply. High performance fans pro-

vide ample optimized cooling for the dual processor modules and 8 hot-swap drive

bays offer maximum storage capacity in a 1U form factor. Only SAS or enterprise

SATA HDDs are recommended.

1-2 Shipping List

Please visit the following link for the latest shipping lists and part numbers for

your particular chassis model http://www.supermicro.com/products/chassis/1U/

?chs=113

Chapter 1: Introduction

1-1

SC113 Chassis

Model CPU HDD I/O Slots

Power

Supply

SC113TQ-700UB

Single/Dual CPU

8x 2.5"

hot-swap

SAS/SATA

2x FH, 1x LP 700W

SC113TQ-700CB

Dual CPU

8x 2.5"

hot-swap

SAS/SATA

1x FF 700W

SC113TQ-R650UB

Single/Dual CPU

8x 2.5"

hot-swap

SAS/SATA

2x FH, 1x LP Redundant

650W

SC113TQ-R650CB

Dual CPU

8x 2.5"

hot-swap

SAS/SATA

1x FF Redundant

650W

SC113TQ-560UB

Single/Dual CPU

8x 2.5"

hot-swap

SAS/SATA

2x FH, 1xLP 560W

FF: Full-height, full length card

FH: Full-height card

LP: Low-profile card

SC113 Chassis Manual

1-2

1-3 Chassis Features

The SC113 1U high-performance chassis includes the following features:

CPU

The SC113 Chassis supports a single or dual CPU. Please refer to the motherboard

specifications pages on our website for updates on supported processors.

Hard Drives

The SC113 chassis features 8 hard drive bays for 2.5" hot-swappable SAS/SATA

drives. Once setup correctly, these drives can be removed without powering down

the server.

I/O Expansion Slots

The SC113 Chassis includes either one full I/O expansion slot or two full I/O expan-

sion slots and one low profile I/O slot. See the chart on the previous page for your

specific chassis model.

Peripheral Drives

Each SC113 Chassis supports one slim DVD-ROM Drive. This drive allows data

to be quickly installed or saved. (On some chassis models, the DVD-ROM is an

optional item).

Other Features

Other on-board features are included to promote system health. These include four

cooling fans, a convenient power switch, reset button, and 5 LED indicators.

1-3

Chapter 1 Introduction

1-4 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Asia-Pacific

Address: Super Micro Computer, Inc.

4F, No. 232-1, Liancheng Rd.

Chung-Ho 235, Taipei County

Taiwan, R.O.C.

Tel: [phone]

Fax: [phone]

Web Site: www.supermicro.com.tw

Technical Support:

Email: [e-mail]

Tel: [phone]

SC113 Chassis Manual

1-4

1-5 Returning Merchandise for Service

A receipt or copy of your invoice marked with the date of purchase is required be-

fore any warranty service will be rendered. You can obtain service by calling your

vendor for a Returned Merchandise Authorization (RMA) number. When returning

to the manufacturer, the RMA number should be prominently displayed on the

outside of the shipping carton, and mailed prepaid or hand-carried. Shipping and

handling charges will be applied for all orders that must be mailed when service

is complete.

For faster service, RMA authorizations may be requested online (http://www.

supermicro.com/support/rma/).

Whenever possible, repack the chassis in the original Supermicro carton, using the

original packaging material. If these are no longer available, be sure to pack the

chassis securely, using packaging material to surround the chassis so that it does

not shift within the carton and become damaged during shipping.

This warranty only covers normal consumer use and does not cover damages in

-

curred in shipping or from failure due to the alteration, misuse, abuse or improper

maintenance of products.

During the warranty period, contact your distributor first for any product problems.

2-1

Chapter 2 System Safety

Chapter 2

System Safety

2-1 Overview

This chapter provides a quick setup checklist to get your chassis up and running.

Following the steps in the order given should enable you to have your chassis set up

and operational within a minimal amount of time. This quick setup assumes that you

are an experienced technician, famailiar with common concepts and terminology.

2-2 Warnings and Precautions

You should inspect the box the chassis was shipped in and note if it was damaged

in any way. If the chassis itself shows damage, file a damage claim with carrier

who delivered your system.

Decide on a suitable location for the rack unit that will hold that chassis. It should

be situated in a clean, dust-free area that is well ventilated. Avoid areas where heat,

electrical noise and electromagnetic fields are generated.

You will also need it placed near at least one grounded power outlet. When con

-

figured, the SC113 chassis includes one power supply. "R" models (i.e. SC113TQ-

R650UB chassis) includes a redundant power supply and require two grounded

outlets.

2-3 Preparing for Setup

The SC113 Chassis includes a set of rail assemblies, including mounting brackets

and mounting screws you will need to install the systems into the rack. Please read

this manual in its entirety before you begin the installation procedure.

SC113 Chassis Manual

2-2

2-4 Electrical Safety Precautions

Basic electrical safety precautions should be followed to protect yourself from harm

and the SC113 from damage:

Be aware of the locations of the power on/off switch on the chassis as well

as the room’s emergency power-off switch, disconnection switch or electrical

outlet. If an electrical accident occurs, you can then quickly remove power from

the system.

Do not work alone when working with high voltage components.

Power should always be disconnected from the system when removing or in

-

stalling main system components, such as the serverboard, memory modules

and the DVD-ROM and floppy drives (not necessary for hot swappable drives).

When disconnecting power, you should first power down the system with the

operating system and then unplug the power cords from all the power supply

modules in the system.

When working around exposed electrical circuits, another person who is fa

-

miliar with the power-off controls should be nearby to switch off the power, if

necessary.

Use only one hand when working with powered-on electrical equipment. This

is to avoid making a complete circuit, which will cause electrical shock. Use

extreme caution when using metal tools, which can easily damage any electrical

components or circuit boards they come into contact with.

Do not use mats designed to decrease electrostatic discharge as protection from

electrical shock. Instead, use rubber mats that have been specifically designed

as electrical insulators.

The power supply power cord must include a grounding plug and must be

plugged into grounded electrical outlets.

Serverboard battery: CAUTION - There is a danger of explosion if the onboard

battery is installed upside down, which will reverse its polarities This battery

must be replaced only with the same or an equivalent type recommended by

the manufacturer. Dispose of used batteries according to the manufacturer’s

instructions.

DVD-ROM Laser: CAUTION - this server may have come equipped with a

DVD-ROM drive. To prevent direct exposure to the laser beam and hazardous

•

•

•

•

•

•

•

•

•

2-3

Chapter 2 System Safety

radiation exposure, do not open the enclosure or use the unit in any uncon-

ventional way.

2-5 General Safety Precautions

Keep the area around the chassis clean and free of clutter.

Place the chassis top cover and any system components that have been re

-

moved away from the system or on a table so that they won’t accidentally be

stepped on.

While working on the system, do not wear loose clothing such as neckties and

unbuttoned shirt sleeves, which can come into contact with electrical circuits or

be pulled into a cooling fan.

Remove any jewelry or metal objects from your body, which are excellent metal

conductors that can create short circuits and harm you if they come into contact

with printed circuit boards or areas where power is present.

After accessing the inside of the system, close the system back up and secure

it to the rack unit with the retention screws after ensuring that all connections

have been made.

2-6 System Safety

Electrostatic discharge (ESD) is generated by two objects with different electrical

charges coming into contact with each other. An electrical discharge is created to

neutralize this difference, which can damage electronic components and printed

circuit boards. The following measures are generally sufficient to neutralize this

difference before contact is made to protect your equipment from ESD:

Do not use mats designed to decrease electrostatic discharge as protection from

electrical shock. Instead, use rubber mats that have been specifically designed

as electrical insulators.

Use a grounded wrist strap designed to prevent static discharge.

Keep all components and printed circuit boards (PCBs) in their antistatic bags

until ready for use.

Touch a grounded metal object before removing any board from its antistatic

bag.

•

•

•

•

•

•

•

•

•

SC113 Chassis Manual

2-4

Do not let components or PCBs come into contact with your clothing, which may

retain a charge even if you are wearing a wrist strap.

Handle a board by its edges only; do not touch its components, peripheral chips,

memory modules or contacts.

When handling chips or modules, avoid touching their pins.

Put the serverboard and peripherals back into their antistatic bags when not

in use.

For grounding purposes, make sure your computer chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and

the serverboard.

•

•

•

•

•

3-1

Chapter 3 Chassis Components

Chapter 3

Chassis Components

3-1 Overview

This chapter describes the most common components included with your chassis.

Some components listed may not be included or compatible with your particular

chassis model. For more information, see the installation instructions detailed later

in this manual.

3-2 Components

Chassis

The chassis includes eight 2.5" hard drive bays, and one slim DVD-ROM drive. (On

some chassis models, the DVD-ROM is an optional item). For the latest shipping

lists, visit our Web site at: http://www.supermicro.com.

This chassis accepts a 1U backplane, four fans (with an optional fifth fan) and one

or two power supplies. SC113 models come in black.

Backplane

Each SC113 chassis comes with a 1U SAS/SATA backplane. For more informa-

tion regarding compatible backplanes, view the appendices found at the end of

this manual. In addition, visit our Web site for the latest information: http://www.

supermicro.com.

Fans

The SC113 chassis accepts four system fans and provides space for two addi-

tional fans if required. System fans for the SC113 chassis are powered from the

serverboard. These fans are 1U high and are powered by 4-pin connectors.

Mounting Rails

The SC113 can be placed in a rack for secure storage and use. To setup your rack,

follow the step-by-step instructions included in this manual.

SC113 Chassis Manual

3-2

Power Supply

Each SC113 chassis model includes one or two high-efficiency power supplies rated

at 560, 650 or 700 Watts. "R" models include a second redundant, hot-swappable

power supply. In the unlikely event your power supply fails, replacement is simple

and can be done without tools.

Air Shroud

Air shrouds are shields, usually plastic, that channel air directly to where it is needed.

Always use the air shroud included with your chassis.

3-3 Where to get Replacement Components

Although not frequently, you may need replacement parts for your system. To

ensure the highest level of professional service and technical support, we strongly

recommend purchasing exclusively from our Supermicro Authorized Distributors /

System Integrators / Resellers. A list of Supermicro Authorized Distributors / System

Integrators /Reseller can be found at: http://www.supermicro.com. Click the Where

to Buy link.

4-1

Chapter 4 System Interface

Chapter 4

System Interface

4-1 Overview

There are several LEDs on the control panel and on the drive carriers that provide

system and component status. This chapter explains the meanings of all LED indi-

cators and the appropriate responses that need to be taken.

Figure 4-1. Control Panel Buttons and LEDs

SC815 Chassis Manual

4-2

Power: The main power switch is used to apply or remove power from the power

supply to the server system. Turning off system power with this button removes

the main power but keeps standby power supplied to the system. Therefore,

you must unplug system before servicing.

•

Reset: The reset button is used to reboot the system.•

4-2 Control Panel Buttons

The SC815 chassis includes two or three push-buttons located on the front panel:

a reset button, a power on/off button, and a UID button

UID: When used with a UID-compatible motherboard, the UID button is used

to turn on or off the blue light function of the the U-LED. Once the blue light is

activated, the unit can be easily located in very large racks and server banks.

•