Supero SAS 815TQ User Manual
Rev. 1.0a
SAS 815TQ Backplane
USER'S GUIDE
+5V
GNDGND+12V
2
I C
+5V +12V
+5V
+12V
#1
#2
#3
#0
ACTIN
ACT0
ACT1
JTAG UPGRADE
JP29:9071RST
JP18:BUZZERRESET
ACT2
ACT3
SIDEBAND
M9
M15
JP10
D3
JP18
J8
J7
J6
J5
JP29
JP44
R144
MH2
M46
J9
J10
JP26
JP47
JP46
JP42
JP33
JP34
JP40 JP51
REV1.00
SAS815TQ
S
UPER
R
ii
SAS 815TQ Backplane User's Guide
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of
this manual, please see our web site at www.supermicro.com.
SUPERMICRO COMPUTER reserves the right to make changes to the product described in this
manual at any time and without notice. This product, including software, if any, and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any
medium or machine without prior written consent.
IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE
OR INABILITY TO USE THIS PRODUCT OR DOCUMENTAT ION, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT HAVE
LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE
PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING
OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all
claims will not exceed the price paid for the hardware product.
Manual Revision 1.0
Release Date: November 1, 2006
Unless you request and receive written permission from SUPER MICRO COMPUTER, you may not
copy or otherwise reproduce/distribute any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2005 by SUPER MICRO COMPUTER INC.
All rights reserved.
Printed in the United States of America
iii
Safety Information and Technical Specifi cations
Table of Contents
Chapter 1: Safety Guidelines
1-1 ESD Safety Guidelines . . . .. . . . . . . . . . .. . . . . . . . . .. . . . . . . . . .. . . . . . . . . . .. . . . . . . . . .. . . . . . . ..................... 1-1
1-2 General Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .................... 1-1
1-3 An Important Note to Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..................... 1-1
Chapter 2: Jumper Settings and Pin Defi nitions
2-1 Front Connectors and Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .................... 2-1
2-2 Front Connector Pin Defi nitions ...................................................................... 2-2
2-3 Front Jumper Locations and Pin Defi nitions .............. ........... .......................... 2-4
2-4 Rear Connectors and LED Indicators ....... ....... ....... ....... ....... ......................... 2-5
iv
SAS 815TQ Backplane User's Guide
Notes
Loading...