Supero AOC-UINF-M2 User Manual
SUPER
®
AOC-UINF-M2
USER'S GUIDE
Rev. 1.0
AOC-UINF-M2
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software, if any,
and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or
reduced to any medium or machine without prior written consent.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara
shall be the exclusive venue for the resolution of any such disputes. Super Micro's total liability
for all claims will not exceed the price paid for the hardware product.
Add-on Card User's Guide
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Manual Revision 1.0
Release Date: March 17, 2008
Unless you request and receive written permission from SUPER MICRO COMPUTER, you may not
copy or otherwise reproduce/distribute any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2008 by SUPER MICRO COMPUTER INC.
All rights reserved.
Printed in the United States of America
ii
Safety Information and Technical Specifi cations
Table of Contents
Introduction
Overview ............................................................................................................iv
Product Features ................................................................................................iv
Supported Operating Systems .......................................................................................v
Required Cables .............................................................................................................v
Supported Platforms .......................................................................................................v
Motherboards ......................................................................................................v
Servers ................................................................................................................v
Contacting Supermicro ......................................................................................vii
Returning Merchandise for Service ................................................................. viii
Chapter 1 Safety Guidelines
1-1 ESD Safety Guidelines ................................................................................... 1-1
1-2 General Safety Guidelines .............................................................................. 1-1
1-3 An Important Note to Users ............................................................................ 1-2
Chapter 2 Add-on Card Components
2-1 Front Connectors and LEDs ........................................................................... 2-1
2-2 Front Connector and LED Defi nitions ............................................................. 2-2
Chapter 3 Installation
3-1 Before Installation ........................................................................................... 3-1
3-2 Hardware Installation ...................................................................................... 3-1
3-3 Windows 2003/XP/2000 Driver Installation ..................................................... 3-2
iii
AOC-UINF-M2
Add-on Card User's Guide
Introduction
Overview
This manual is written for system integrators, PC technicians and knowledgeable
PC users who intend to integrate Supermicro's AOC-UINF-M2 Add-on Card.
Product Features
The AOC-UINF-M2 offers the following features:
Mellanox
•
Low-profi le UIO form factor
•
Dual CX4 Connectors
•
20Gb/s per port
•
PCI-e X8 2.0
•
RoHS compliant 5/6
•
®
ConnectX DDR MT25408A0-FCC-GI Controller
iv
Safety Information and Technical Specifi cations
Supported Operating Systems
The AOC-UINF-M2 supports the following Operating Systems (OS):
•
Windows
Linux
•
VMWare ESX Server
•
Novell
•
Required Cables
The AOC-UINF-M2 requires CX4 copper-based cable:
Up to 10m for 20Gb/s or 20m for 10Gb/s
•
Supported Platforms
Motherboards
The following motherboards support the AOC-UINF-M2 add-on card.
H8SMU, PDSMU, X7DAL-E, X7DAL-E+, X7DBN, X7DBU, X7DCU, X7DWA-N,
X7DWN+, X7DWU or H8DMU+.
Servers
The following servers support the AOC-UINF-M2 add-on card.
5015M-Ni, 5015M-NT, 5015M-UR, 6015B-NT, 6015B-NTR, 6015B-U, 6015B-UR,
6015C-Ni, 6015C-NTR, 6015C-UR, 6015W-Ni, 6015W-NTR, 6015W-UR, 5025M-
UR, 6025C-UR, 6025W-NTR+, 6025W-UR, 7045A-WT, 1011M-UR, 1011M-Ni and
1021M-UR+
v
Loading...