Supero A1SAi-2550F, A1SRi-2558F, A1SRi-2758F, A1SAi-2750F, A1SRi-2358F User Manual

A1SAi-2550F

A1SAi-2750F
A1SRi-2358F
A1SRi-2558F
A1SRi-2758F

USER’S MANUAL

Revision 1.0c

The information in this user’s manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
and makes no commitment to update or to keep current the information in this manual, or to notify
any person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our website at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu­mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.

IN NO EVENT WILL SUPER MICRO COMPUTER, INC. BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE
USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC.
SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED
WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between the manufacturer and the customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of Santa Clara
shall be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for
all claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”.

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.

Manual Revision 1.0c

Release Date: May 5, 2016

Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.

Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2016 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

iii

Preface

This manual is written for system integrators, IT technicians and

knowledgeable end users. It provides information for the installation and use of the

A1SAi-2750F(-2550F)/A1SRi-2758F(-2558F, -2358F) Series motherboard.

About This Motherboard

The A1SAi & A1SRi Series motherboard supports a next-generation Intel®

C2000 SoC (System-on-a-Chip) processor in an FCBGA package. With a C2000 Se-

ries processor built in, the A1SAi/A1SRi Series motherboard supports all-purpose,

cutting-edge technology such as ECC SODIMM, up to 64GB memory capacity, In-

tel's Virtualization Technology, Turbo Boost Technology, or QuickAssist Technology,

offering unprecedented enhancements to data integrity, internet security, network

communication, system performance, power efciency and scalability. This mother-

board is optimized for network applications, web hosting, dedicated storage/server,

and cloud computing. It is ideal for communications systems, embedded solutions,

server or storage platforms. Please refer to our website at (http://www.supermicro.

com/products/) for processor and memory support updates. This product is intended

to be installed and serviced by professional technicians.

Manual Organization

Chapter 1 describes the features, specications and performance of the moth-

erboard, and provides detailed information on the Intel C2000 Series processor.

Chapter 2 provides hardware installation instructions. Read this chapter when in-

stalling the processor, memory modules and other hardware components into the

system. If you encounter any problems, see Chapter 3, which describes trouble-

shooting procedures for video, memory and system setup stored in the CMOS.

Chapter 4 includes an introduction to the BIOS, and provides detailed information

on running the CMOS Setup utility.

Appendix A provides BIOS Error Beep Codes.

Appendix B lists software program installation instructions.

Appendix C contains UEFI BIOS Recovery instructions.

Preface

iv

Conventions Used in the Manual:

Special attention should be given to the following symbols for proper installation and

to prevent damage done to the components or injury to yourself:

Warning: Critical information to prevent damage to the components or injury to your-

self.

Important: Important information given to ensure proper system installa-

tion or to relay safety precautions.

Note: Additional Information given to differentiate various models or to

provide instructions for correct system setup.

A1SAi & A1SRi Series Motherboard User’s Manual

v

Contacting Supermicro

Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

Website: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Website: www.supermicro.nl

Asia-Pacic

Address: Super Micro Computer, Inc.

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 235

Taiwan (R.O.C)

Tel: [phone]

Fax: [phone]

Email: [e-mail]

Website: www.supermicro.com.tw

vi

Table of Contents

Preface

About This Motherboard ................................................................................................ iii

Manual Organization .....................................................................................................iii

Conventions Used in the Manual: .................................................................................iv

Contacting Supermicro ...................................................................................................v

Chapter 1 Introduction

1-1 Overview ......................................................................................................... 1-1

Checklist .......................................................................................................... 1-1

Motherboard Features ..................................................................................... 1-7

1-2 Processor Overview ..................................................................................... 1-10

1-3 Special Features ............................................................................................1-11

Recovery from AC Power Loss ......................................................................1-11

1-4 PC Health Monitoring .....................................................................................1-11

Environmental Temperature Control ..............................................................1-11

System Resource Alert ..................................................................................1-11

1-5 ACPI Features ............................................................................................... 1-12

1-6 Power Supply ................................................................................................ 1-12

Chapter 2 Installation

2-1 Standardized Warning Statements ................................................................. 2-1

Battery Handling .............................................................................................. 2-1

Product Disposal ............................................................................................. 2-3

2-2 Static-Sensitive Devices .................................................................................. 2-4

Precautions ..................................................................................................... 2-4

Unpacking ....................................................................................................... 2-4

2-3 Memory Support .............................................................................................. 2-5

Memory Population Guidelines ....................................................................... 2-5

Populating Memory Modules........................................................................... 2-6

Installing DIMM Memory Modules ................................................................... 2-6

Removing Memory Modules ........................................................................... 2-6

2-4 Motherboard Installation .................................................................................. 2-8

Tools Needed .................................................................................................. 2-8

Location of Mounting Holes ............................................................................ 2-8

Installing the Motherboard .............................................................................. 2-9

2-5 Connectors/IO Ports ...................................................................................... 2-10

I/O Back Panel .............................................................................................. 2-10

Serial Ports ................................................................................................2-11

A1SAi & A1SRi Series Motherboard User’s Manual

vii

Ethernet Ports ...........................................................................................2-11

Universal Serial Bus (USB) ...................................................................... 2-12

Unit Identier Switch ................................................................................ 2-13

VGA .......................................................................................................... 2-13

Front Control Panel ....................................................................................... 2-14

Front Control Panel Pin Denitions............................................................... 2-15

NMI Button ............................................................................................... 2-15

Power LED .............................................................................................. 2-15

HDD LED .................................................................................................. 2-16

NIC1/NIC2 (LAN1/LAN2) .......................................................................... 2-16

Overheat (OH)/Fan Fail/PWR Fail/UID LED ............................................ 2-17

Power Fail LED ........................................................................................ 2-17

Reset Button ........................................................................................... 2-18

Power Button ........................................................................................... 2-18

2-6 Connecting Cables ........................................................................................ 2-19

ATX PWR, DC PWR and HDD PWR Connectors (JPW1, J1, J3) .......... 2-19

Fan Headers (Fan 1 ~ Fan 3) .................................................................. 2-20

Chassis Intrusion (JL1) ........................................................................... 2-20

Internal Buzzer (SP1) ............................................................................... 2-21

Power LED/Speaker ................................................................................. 2-21

DOM PWR Connector (JSD1) .................................................................. 2-22

Overheat LED Header .............................................................................. 2-22

TPM Header/Port 80 Header ................................................................... 2-23

LAN3/LAN4 Activity LED Header ............................................................. 2-23

Power SMB (I2C) Connector .................................................................... 2-24

System Management Bus Header ........................................................... 2-24

2-7 Jumper Settings ............................................................................................ 2-25

Explanation of Jumpers ................................................................................ 2-25

LAN Ports Enable/Disable ........................................................................ 2-25

CMOS Clear ............................................................................................. 2-26

PCI-E Slot SMB Enable (I2C1/I2C2) ......................................................... 2-26

Watch Dog Timer Enable ......................................................................... 2-27

VGA Enable .............................................................................................. 2-27

2-8 Onboard Indicators ........................................................................................ 2-28

GbE LAN LEDs ........................................................................................ 2-28

IPMI Dedicated LAN LEDs ....................................................................... 2-28

Onboard Power LED ............................................................................... 2-29

Overheat/PWR Fail/Fan Fail LED ............................................................ 2-29

Unit Identication LED .............................................................................. 2-30

Table of Contents

viii

2-9 SATA Connections ......................................................................................... 2-31

Serial ATA Ports........................................................................................ 2-31

Chapter 3 Troubleshooting

3-1 Troubleshooting Procedures ........................................................................... 3-1

Before Power On ............................................................................................ 3-1

No Power ........................................................................................................ 3-1

No Video ......................................................................................................... 3-1

Memory Errors ............................................................................................... 3-2

Losing the System’s Setup Conguration ....................................................... 3-2

3-2 Technical Support Procedures ........................................................................ 3-3

3-3 Frequently Asked Questions ........................................................................... 3-4

3-4 Battery Removal and Installation .................................................................... 3-5

Battery Removal .............................................................................................. 3-5

Proper Battery Disposal .................................................................................. 3-5

Battery Installation ........................................................................................... 3-5

3-5 Returning Merchandise for Service................................................................. 3-6

Chapter 4 BIOS

4-1 Introduction ...................................................................................................... 4-1

4-2 Main Setup ...................................................................................................... 4-3

4-3 Advanced Setup Congurations...................................................................... 4-4

4-4 IPMI ............................................................................................................... 4-29

4-6 Boot ............................................................................................................... 4-33

4-7 Security ......................................................................................................... 4-34

4-8 Save & Exit ................................................................................................... 4-37

Appendix A BIOS Error Beep Codes

A-1 BIOS Error Beep Codes .................................................................................A-1

Appendix B Software Installation Instructions

B-1 Installing Software Programs ..........................................................................B-1

B-2 Installing SuperDoctor5 ...................................................................................B-2

Appendix C UEFI BIOS Recovery Instructions

C-1 An Overview to the UEFI BIOS ......................................................................C-1

C-2 How to Recover the UEFI BIOS Image (the Main BIOS Block) .....................C-1

C-3 To Recover the Main BIOS Block Using a USB-Attached Device..................C-1

A1SAi & A1SRi Series Motherboard User’s Manual

Chapter 1: Introduction

1-1

Chapter 1

Introduction

1-1 Overview

Checklist

Congratulations on purchasing your computer motherboard from an acknowledged

leader in the industry. Supermicro boards are designed with the utmost attention to

detail to provide you with the highest standards in quality and performance.

Please check that the following items have all been included with your motherboard.

If anything listed here is damaged or missing, contact your retailer.

The following items are included in the retail box:

• One (1) Supermicro Motherboard

• Six (6) SATA cables (four (4) for A1SRi-2358F)

• One (1) I/O shield

• One (1) Quick Reference Guide

Note: For your system to work properly, please follow the links below to

download all necessary drivers/utilities and the user's manual for your

motherboard.

SMCI product manuals: http://www.supermicro.com/support/manuals/

Product Drivers and utilities: ftp://ftp.supermicro.com/

If you have any questions, please contact our support team at support@supermicro.

com.

1-2

A1SAi & A1SRi Series Motherboard User’s Manual

A1SAi & A1SRi Series Motherboard Image

Note 1: All graphics shown in this manual were based upon the latest PCB Revision

available at the time of publishing of the manual. The motherboard you've received

may or may not look exactly the same as the graphics shown in this manual.

Note 2: I-SATA4/5 and DIMMB1/B2 are not available on A1SRi-2358F.

Chapter 1: Introduction

1-3

A1SAi & A1SRi Series Motherboard Layout

Important Notes to the User

1. See Chapter 2 for detailed information on jumpers, I/O ports and JF1 front

panel connections.

2. " " indicates the location of "Pin 1". Jumpers not indicated are for testing

only.

3. I-SATA4/5 and DIMMB1/B2 are not available on A1SRi-2358F.

4. When LED3 (Onboard Power LED Indicator) is on, system power is on.

Unplug the power cable before installing or removing any components.

5. The A1SRi Series motherboard supports Intel® QuickAssist technology to

enhance network routing and internet security for communications systems.

6. The A1SAi Series motherboard supports Turbo Boost Technology, offering

turbo-boost capabilities to maximize system performance for server plat-

forms. Refer to the Model Variation table on page 1-6 for more details.

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

1-4

A1SAi & A1SRi Series Motherboard User’s Manual

A1SAi & A1SRi Series Motherboard Quick Reference

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

Mothrboard Model Name

A1SAi-2750F

A1SAi-2550F A1SRi-2758F A1SRi-2558F A1SRi-2358F

SoC Code Name

Avoton

Avoton

Rangeley

Rangeley Rangeley

Processor Number C2750 C2550 C2758 C2558 C2358

# of Cores 8 4 8 4 2

# of Threads 8 4 8 4 2

Clock Speed 2.4 GHz 2.4 GHz 2.4 GHz 2.4 GHz 1.7 GHz

Max Turbo Frequency 2.6 GHz 2.6 GHz N/A N/A 2.0 GHz

Intel® QuickAssist Technology No No Yes Yes Yes

Instruction Set 64-bit 64-bit 64-bit 64-bit 64-bit

Embedded Options Available No No Yes Yes Yes

SoC Max TDP 20 W 14 W 20 W 15 W 7W

# of Memory Channels 2 2 2 2 1

Intel® Turbo Boost Technology Yes Yes No No Yes

Intel® Virtualization Technology (VT-x) Yes Yes Yes Yes Yes

AES New Instructions Yes Yes Yes Yes Yes

Intel® Hyper-Threading Technology No No No No No

Intel® QuickAssist Technology No No Yes Yes Yes

A1SAi/A1SRi Series Motherboard Model Variation Table

Chapter 1: Introduction

1-5

Jumpers

Jumper Description Default

JBT1 CMOS Clear Off (Normal)

JI2C1/JI2C2 SMB to PCI-Exp. Slots Off (Disabled)

JPG1 VGA Enable Pins 1-2 (Enabled)

JPL1 Ethernet LAN Ports Enable Pins 1-2 (Enabled)

JWD1 Watch Dog Enable Pins 1-2 (Reset)

Headers/Connectors

Connector Description

Battery Onboard Battery (JBAT1)

COM1/COM2 COM1/COM2 Port Headers

FAN1-FAN3 CPU/System Cooling Fans

J1* 4-pin 12V DC Power Connector (to provide alternative power to embedded

devices such as SC101i, when the 24-pin ATX power is not in use)

J3 4-pin Power Connector for HDD use (to provide power from the motherboard

to onboard HDD devices)

JD1 Power LED/Speaker Header(Pins 1-3: Power LED, Pins 6-7: Internal

Buzzer, Pins 4-7: External Speaker)

JF1 Front Panel Control Header

JIPMB1 4-pin External SMbus I2C Header (for an IPMI Card)

JL1 Chassis Intrusion Header

JOH1 Overheat LED Header

JPI2C1 Power Supply System Management Bus (SMBus) I2C Header

JPK1 LAN3/LAN4 LED Indication Header

JPW1* 24-pin ATX Power Connector

JSD1 SATA DOM (Device_On_Module) Power Connector

JTPM1 Trusted Platform Module (TPM)/Port 80 Connector

JUID1 Unit Identier (UID) Switch

LAN1/LAN3, LAN2/LAN4 Gigabit Ethernet (RJ45) Ports

PCI-E Slot PCI-E 2.0 x 8 Slot

I-SATA0-I-SATA5 Intel Serial ATA Ports 0-5 (Ports 4/5 not available on the A1SRi-2358F)

SP1 Internal Speaker/Buzzer

USB 2.0 0/1 USB 2.0 Ports on the Rear I/O Panel

USB 3.0 0/1 USB 3.0 Ports on the Rear I/O Panel

USB 3.0 2/3 One USB 3.0 Port via Header + One USB 3.0 Port via Type-A

VGA Backpanel VGA Port

(*Do not use the 4-pin DC power at J1 when the 24-pin ATX Power at JPW1 is connected to the power supply. Do
not plug in both J1 and JPW1 at the same time.)

1-6

A1SAi & A1SRi Series Motherboard User’s Manual

LED Indicators

LED Description Color/State Status

LED2 BMC Heartbeat LED Green: Blinking BMC: Normal

LED3 Power LED Green: On System PWR On

LED7 UID Switch LED Blue: On Unit Identied

LED8 Overheat/PWR Fail/Fan Fail LED Red: Solid on/Blinking

Solid On: Overheat,
Blinking: PWR Fail or Fan Fail

Note: The A1SRi Series motherboard supports Intel QuickAssist technol-

ogy to enhance network routing and internet security for communications

systems. The A1SAi Series motherboard supports Turbo Boost Technology,

offering turbo boost capabilities to maximize system performance for server

platforms. Refer to the Model Variation table below for details.

Mothrboard Model Name

A1SAi-2750F

A1SAi-2550F A1SRi-2758F A1SRi-2558F A1SRi-2358F

SoC Code Name

Avoton

Avoton

Rangeley

Rangeley Rangeley

Processor Number C2750 C2550 C2758 C2558 C2358

# of Cores 8 4 8 4 2

# of Threads 8 4 8 4 2

Clock Speed 2.4 GHz 2.4 GHz 2.4 GHz 2.4 GHz 1.7 GHz

Max Turbo Frequency 2.6 GHz 2.6 GHz N/A N/A 2.0 GHz

Intel® QuickAssist Technology No No Yes Yes Yes

Instruction Set 64-bit 64-bit 64-bit 64-bit 64-bit

Embedded Options Available No No Yes Yes Yes

SoC Max TDP 20 W 14 W 20 W 15 W 7W

# of Memory Channels 2 2 2 2 1

Intel® Turbo Boost Technology Yes Yes No No Yes

Intel® Virtualization Technology (VT-x) Yes Yes Yes Yes Yes

AES New Instructions Yes Yes Yes Yes Yes

Intel® Hyper-Threading Technology No No No No No

Intel® QuickAssist Technology No No Yes Yes Yes

A1SAi/A1SRi Series Motherboard Model Variation Table

Chapter 1: Introduction

1-7

Motherboard Features

CPU Single Intel® C2000 Tri-Gate 22nm SoC in the FCBGA

1283 package (Formerly Avoton Rangeley)

Each SoC supports 2, 4, or 8 Cores

Refer to the Model Variation table on page 1-4 or 1-6 for

SoC support on each MB SKU

Memory A1SAi-2550F/2750F + A1SRi-2558F/2758F

Four (4) DIMMs memory slots support up to 64 GB of

SO-DDR3 Unbuffered ECC 1600/1333 MHz (1.5V, 1.35V)

memory; populate identical memory (of the same type/

speed/size) in all slots

A1SRi-2358F

Two (2) slots support up to 16GB of SO-DDR3 Unbuffered

ECC 1333MHz. (Some 1600MHz memory can be used,

but they will operate at 1333MHz.)

Dual-Channel memory or Single-Channel w/x8 data width,

Single or Dual Rank memory

DIMM sizes

DIMMs 2 GB, 4GB, 8GB, and 16GB ECC SODIMM

(16GB not suppoted on A1SRi-2358F)

Expansion Slot One (1) PCI Express 2.0 x8 slot

Network Connections C2000 Series SoC I354 built-in Quad-port GbE control-

lers (MACs) w/Marvell 88E1543 Transceiver

Four (4) RJ-45 rear I/O panel connectors with Link and
Activity LEDs

One (1) Dedicated IPMI LAN Port (Realtek 8211E-PHY)

I/O Devices SATA Connections

SATA 3.0

(6Gb/s)

Two (2) SATA 3.0 (I-SATA 0/1)

SATA 2.0

(3Gb/s)

Four (2) SATA 2.0 (I-SATA 2-5)
Two (2) on A1SRi-2358F

USB Devices

Two (2) USB 3.0 ports on the rear I/O panel (USB 3.0­0/1)
One (1) USB 3.0 port on Type-A connector
One (1) USB 3.0 port via internal header

Two (2) USB 2.0 on the rear I/O panel (USB2.0-0/1)

1-8

A1SAi & A1SRi Series Motherboard User’s Manual

Serial (COM) Ports

One (1) COM port on the rear I/O panel (COM1)
One (1) front accessible COM port header (COM2)

IPMI 2.0

IPMI 2.0 supported by Aspeed AST2400 BMC (Base­board Management Controller)

VGA (Graphics Display)

One (1) VGA Port on the rear I/O panel supported by the
Aspeed AST2400 VGA Controller

BIOS 64 Mb AMI BIOS® SPI EEPROM BIOS

Plug and Play, DMI 2.0, PCI 2.3, ACPI 5.0, USB Key­board, SMBIOS 2.7, and UEFI 2.3.1

Power Conguration ACPI/ACPM Power Management (S0 and S5 only)

Main Switch Override Mechanism

Power-on mode for AC power recovery

PC Health Monitoring Onboard Voltage Monitoring

VCCP, VDIMM, 12V, 5VCC, 3.3VCC, VBAT, 5V, Dual, and

3.3V AUX

CPU 1+1-phase switching voltage regulator

CPU/System overheat LED and control

CPU Thermal Trip support

SoC Thermal Control Circuit (TCC) mechanism

Thermal Monitor Support

Fan Control

Low noise fan speed control

BMC Health Monitoring

BMC Fan control and thermal alert by sensors monitor­ing, including CPU, memory and motherboard ambient
temperatures

System Management PECI (Platform Environment Conguration Interface) 3.0

System resource alert via SuperDoctor® 5

SuperDoctor® 5, Watch Dog, NMI

Chassis Intrusion header and detection

CD Utilities Download from www.supermicro.com

Other ROHS (Full Compliance, Lead Free)

Operating Temperature 00-600C

Dimensions Mini iTX form factor (6.75" x 6.75") (171.45 mm x 171.45

mm)

Note: Please refer to Note 5 and Note 6 on page 1-3 for Intel® QuickAssist

technology and Turbo Boost technology support.

Chapter 1: Introduction

1-9

System Block Diagram

Note: This is a general block diagram and may not exactly represent

the features on your motherboard. See the Motherboard Features

pages for the actual specications of each motherboard.

A1SAi & A1SRi Series motherboard Block Diagram

CHB

B1

A2

PEG [8..15]

FLASH 64Mb

SO - DIMM

CHA

LPC

SATA 3.0

PCIE 2.0 x 8 SLOT

A1

SO - DIMM

TPM HDR

C2000 SOC

VGA

FAN x 3

SO - DIMM

SATA 2.0

SATA GEN2

SO - DIMM

SATA 3.0

SATA GEN3

CHACHB

PEG [7]

PEG [3]

PCIE x 8

AST2400

PCIE x 1

COM1

COM2

SATA 2.0

SATA 2.0

SATA 2.0

RJ45

RTL8211E

SGMII x 4

Marvell
88E1543

10BASE-T/100BASE-T/1000BASE-T

LAN1

LAN3

LAN2

LAN4

+

SPI

USB [0:1]

USB [2:3]

TX/RX
(debug)

0Ohm
NI

LPC

UART1 UART2

B2

USB 2.0 X 2

Renesas
720201

USB 3.0 X 4

TYPE-A

USB

HEADER

+

+

REAR

REAR

PCIE x 1

GbE LAN

DIMMB1/B2 not available on A1SRi-2358F

A1SRi-2358F (Two SATA 2.0 only)

A1SAi-2550F/2750F (Four SATA 2.0)

REAR

1-10

A1SAi & A1SRi Series Motherboard User’s Manual

1-2 Processor Overview

The A1SAi/A1SRi Series motherboard supports a 2nd-generation 64-bit, Intel

Atom™ C2000 Tri-Gate SoC (System-on-a-Chip) processor based on low-power

Silvermont microarchitecture in an FCBGA 1283 package. Built upon the func-

tionality and capability of the C2000 Series processor in the low-power 22nm

microarchitecture, the A1SAi/A1SRi Series motherboard provides unprecedented

enhancements to network routing, internet security, system performance, and power

efciency.

The C2000 SoC Series processor features an Out-of-Order Execution Engine and

offers new multi-core and system fabric architecture capable of utilizing up to eight

CPU cores to achieve improved single-thread performance. This new SoC proces-

sor also provides an operating range with wider dynamic power and enhanced

power management. In addition, the A1SRi Series motherboard supports the Intel

QuickAssist Technology, which provides hardware acceleration to help enhance

cryptographic performance, secure internet trafc, and boost network routing,

freeing up processor resources for application processing, while the A1SAi Series

motherboard supports the Intel Turbo Boost Technology, which offers turbo-boost

capabilities to maximize system performance.

Intel® C2000 Series Processor Features

The C2000 Series processor offers the following features:

• Up to 64GB ECC memory support (up to 16GB for A1SRi-2358F)

• Enterprise Class I354 Quad GbE LAN Controller

• Four SATA2 ports and two SATA3 ports (Two SATA2 and two SATA3 for A1SRi-

2358F)

• SSE Extensions

• AES-NI

• Highly-Optimized Power Management Unit

• Server-Class Reliability, Availability and Serviceability (RAS)

• Intel Virtualization Technology (VTx)

• Intel QuickAssist Technology (A1SRi Series only)

• Intel Turbo Boost Technology (A1SAi Series + A1SRi-2358F only)

Chapter 1: Introduction

1-11

1-3 Special Features

Recovery from AC Power Loss

Basic I/O System (BIOS) provides a setting for you to determine how the system will

respond when AC power is lost and then restored to the system. You can choose

for the system to remain powered off, (in which case you must press the power

switch to turn it back on), or for it to automatically return to a power-on state. See

the Advanced BIOS Setup section to change this setting. The default setting is

Last State.

1-4 PC Health Monitoring

This section describes the PC health monitoring features of the board. All have

an onboard System Hardware Monitoring chip that supports PC health monitoring.

An onboard voltage monitor will scan these onboard voltages continuously: VCCP,

VDIMM, 12V, 5VCC, 3.3VCC, VBAT, 5V, Dual, and 3.3V AUX. Once a voltage be-

comes unstable, a warning is given, or an error message is sent to the screen. The

user can adjust the voltage thresholds to dene the sensitivity of the voltage monitor.

Environmental Temperature Control

This motherboard comes with a built-in passive heatsink. Please follow the instruc-

tions given in your system design guide or your system user manual to provide

proper/adequate airow to your system. The onboard BaseBoard Management

Controller (BMC) monitors CPU, memory and motherboard environment tempera-

tures for fan control and PC health management.

Note: To avoid possible system overheating, please be sure to provide

adequate airow to your system.

System Resource Alert

This feature is available when the system is used with SuperDoctor® 5 in the

Windows OS environment or used with SuperDoctor II in Linux. SuperDoctor

is used to notify the user of certain system events. For example, you can also

congure SuperDoctor to provide you with warnings when the system temperature,

CPU temperatures, voltages and fan speeds go beyond predened thresholds.

1-12

A1SAi & A1SRi Series Motherboard User’s Manual

1-5 ACPI Features

ACPI stands for Advanced Conguration and Power Interface. The ACPI specica-

tion denes a exible and abstract hardware interface that provides a standard

way to integrate power management features throughout a PC system, including

its hardware, operating system and application software. This enables the system

to automatically turn on and off peripherals such as CD-ROMs, network cards, hard

disk drives and printers.

In addition to enabling operating system-directed power management, ACPI also

provides a generic system event mechanism for Plug and Play, and an operating

system-independent interface for conguration control. ACPI leverages the Plug and

Play BIOS data structures, while providing a processor architecture-independent

implementation that is compatible with Windows 7, Windows 8, and Windows 2008

Operating Systems. A1SAi/A1SRi Series motherboards support S0 and S5 only.

1-6 Power Supply

As with all computer products, a stable power source is necessary for proper and

reliable operation. It is even more important for processors that have high CPU

clock rates.

Note 1: The A1SAi and A1SRi Series motherboard alternatively supports

a 4-pin 12V DC input power supply for embedded applications. The 12V

DC input is limited to 12A by design. It provides up to 144W power input

to the motherboard. Please keep onboard power use within the power

limits specied above. Over-current DC power use may cause damage

to the motherboard!

Note 2: Do not use the 4-pin DC power at J1 when the 24-pin ATX Power

at JPW1 is connected to the power supply. Do not plug in both J1 and

JPW1 at the same time.

It is strongly recommended that you use a high quality power supply that meets ATX

power supply Specication 2.02 or above. It must also be SSI compliant. (For more

information, please refer to the website at http://www.ssiforum.org/). Additionally, in

areas where noisy power transmission is present, you may choose to install a line lter

to shield the computer from noise. It is recommended that you also install a power

surge protector to help avoid problems caused by power surges.

Chapter 2: Installation

2-1

Chapter 2

Installation

2-1 Standardized Warning Statements

The following statements are industry-standard warnings, provided to warn the user

of situations which have the potential for bodily injury. Should you have questions or

experience difculty, contact Supermicro's Technical Support department for assis-

tance. Only certied technicians should attempt to install or congure components.

Read this section in its entirety before installing or conguring components in the

Supermicro chassis.

Battery Handling

Warnung

Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die

Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.

Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.

Warning!

There is a danger of explosion if the battery is replaced incorrectly. Replace the

battery only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's instructions

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。 交換する電池はメー
カーが推奨する型、または同等のものを使用下さい。 使用済電池は製造元の指示に従
って処分して下さい。

警告

电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更

换原有电池。请按制造商的说明处理废旧电池。

警告

電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有

電池。請按照製造商的說明指示處理廢棄舊電池。

2-2

A1SAi & A1SRi Series Motherboard User’s Manual

Attention

Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer

que par une pile de type semblable ou équivalent, recommandée par le fabricant.

Jeter les piles usagées conformément aux instructions du fabricant.

¡Advertencia!

Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Re-

emplazar la batería exclusivamente con el mismo tipo o el equivalente recomen-

dado por el fabricante. Desechar las baterías gastadas según las instrucciones

del fabricante.

!הרהזא

תנכס תמייקץוציפ .הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי

גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ.

תוללוסה קוליס תושמושמה עצבל שי .ןרציה תוארוה יפל









경고!

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일
하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다. 제조사
의 안내에 따라 사용된 배터리를 처리하여 주십시오.

Waarschuwing

Er is ontplofngsgevaar indien de batterij verkeerd vervangen wordt. Vervang de

batterij slechts met hetzelfde of een equivalent type die door de fabrikant aan-

bevolen wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften

afgevoerd te worden.

Chapter 2: Installation

2-3

Product Disposal

Warning!

Ultimate disposal of this product should be handled according to all national laws

and regulations.

製品の廃棄

この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が

ありま す。

警告
本产品的废弃处理应根据所有国家的法律和规章进行。

警告
本產品的廢棄處理應根據所有國家的法律和規章進行。

Warnung

Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen

des Landes erfolgen.

¡Advertencia!

Al deshacerse por completo de este producto debe seguir todas las leyes y regla-

mentos nacionales.

Attention

La mise au rebut ou le recyclage de ce produit sont généralement soumis à des

lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de

l'organisme compétent.

רצומה קוליס

!הרהזא

ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס.הנידמה יקוח

2-4

A1SAi & A1SRi Series Motherboard User’s Manual

2-2 Static-Sensitive Devices

Electrostatic-Discharge (ESD) can damage electronic com ponents. To avoid dam-

aging your system board, it is important to handle it very carefully. The following

measures are generally sufcient to protect your equipment from ESD.

Precautions

• Use a grounded wrist strap designed to prevent static discharge.

• Touch a grounded metal object before removing the board from the antistatic

bag.

• Handle the board by its edges only; do not touch its components, peripheral

chips, memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the motherboard and peripherals back into their antistatic bags when not in

use.

• For grounding purposes, make sure your computer chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and

the motherboard.

• Use only the correct type of onboard CMOS battery. Do not install the onboard

battery upside down to avoid possible explosion.

Unpacking

The motherboard is shipped in antistatic packaging to avoid static damage. When

unpacking the board, make sure that the person handling it is static protected.

Waarschuwing

De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming

met alle nationale wetten en reglementen.

 

경고!

이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.

Chapter 2: Installation

2-5

2-3 Memory Support

The A1SAi & A1SRi Series motherboard supports up to 64GB of DDR3 ECC

Unbuffered SODIMM 1600/1333 MHz in four memory slots. The A1SRi-2358F

supports up to 16GB at 1333MHz in two slots: DIMMA1 and DIMMA2. Populating

these DIMM modules with a pair of memory modules of the same type and same

size will result in interleaved memory, which will improve memory performance.

Note: Check the Supermicro website for recommended memory modules.

CAUTION

Exercise extreme care when installing or removing DIMM

modules to prevent any possible damage.

DIMMA1

DIMMA2

DIMMB2

DIMMB1

CPU

Memory Population Guidelines

Please follow the table below when populating the motherboard.

DIMMA1

DIMMA2

DIMMB2

DIMMB1

Towards the CPU

Towards the CPU

Unbuffered DDR3 ECC SODIMM Population

DIMMA1 Slot DIMMB1 Slot DIMMA2 Slot DIMMB2 Slot Total System Memory

4GB 4GB 8GB

4GB 4GB 4GB 4GB 16GB

8GB 8GB 16GB

8GB 8GB 8GB 8GB 32GB

16GB 16GB 16GB 16GB 64GB

Note: Some 1600MHz modules can be used with the A1SRi-2358F, but

they will operate as 1333MHz.

2-6

A1SAi & A1SRi Series Motherboard User’s Manual

Removing Memory Modules

Use your thumbs to gently push the side clips near both ends away from the module

to release it from the socket. Once the module is loosened from the socket, pull

the DIMMs module upwards.

Module Notch

Side Clips

Module Key

Socket Key

Installing DIMM Memory Modules

1. Align the key on the bottom of the DIMM module against the receptive point

on the memory slot. Take note of the notches on the side of the DIMM mod-

ule, and of the locking clips on the socket to avoid causing damage.

2. Install the DIMMs module straight down into the socket until it is securely

seated in the socket. The side clips will automatically lock the module into

place.

Populating Memory Modules

Note 1: Install the desired number of DIMMs into the memory slots, starting

with DIMMA1, then DIMMB1, then DIMMA2, then DIMMB2. Pay attention

to the notch along the bottom of the module to prevent incorrect DIMM

module installation. DIMMB1/B2 are not available on A1SRi-2358F.

Note 2: The motherboard will support one, two, or four DIMM modules.

However, for best memory performance, please install DIMM modules in

pairs.

Note 3: Insert only identical memory modules of the same part number

into the memory slots to ensure that only memory modules of the same

type, same frequency, same speed and same capacity are used on the

same motherboard.

Chapter 2: Installation

2-7

Note: Due to memory allocation to system devices, the amount of mem-

ory that remains available for operational use will be reduced when 4 GB

of RAM is used. The reduction in memory availability is disproportional.

See the following table for details.

Possible System Memory Allocation & Availability

System Device Size Physical Memory

Remaining (-Available)

(4 GB Total System

Memory)

Firmware Hub ash memory (System BIOS) 1 MB 3.99

Local APIC 4 KB 3.99

Area Reserved for the chipset 2 MB 3.99

I/O APIC (4 Kbytes) 4 KB 3.99

PCI Enumeration Area 1 256 MB 3.76

PCI Express (256 MB) 256 MB 3.51

PCI Enumeration Area 2 (if needed) -Aligned on 256-MB
boundary-

512 MB 3.01

VGA Memory 16 MB 2.85

TSEG 1 MB 2.84

Memory available to OS and other applications 2.84

2-8

A1SAi & A1SRi Series Motherboard User’s Manual

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

Caution: 1) To avoid damaging the motherboard and its components, please do

not use a force greater than 8 lb/inch on each mounting screw during motherboard

installation. 2) Some components are very close to the mounting holes. Please take

precautionary measures to avoid damaging these components when installing the

motherboard to the chassis.

2-4 Motherboard Installation

All motherboards have standard mounting holes to t different types of chassis.

Make sure that the locations of all the mounting holes for both motherboard and

chassis match. Although a chassis may have both plastic and metal mounting fas-

teners, metal ones are highly recommended because they ground the motherboard

to the chassis. Make sure that the metal standoffs click in or are screwed in tightly.

Then use a screwdriver to secure the motherboard onto the motherboard tray.

Tools Needed

Philips Screwdriver

(1)

Standoffs (4)

Only if Needed

Philips Screws (4)

Location of Mounting Holes

Chapter 2: Installation

2-9

Installing the Motherboard

1. Install the I/O shield into the back of the chassis.

2. Locate the mounting holes on the motherboard. (See the previous page.)

3. Locate the matching mounting holes on the chassis. Align the mounting holes

on the motherboard against the mounting holes on the chassis.

4. Install standoffs in the chassis as needed.

5. Install the motherboard into the chassis carefully to avoid damaging other

motherboard components.

6. Using the Phillips screwdriver, insert a Phillips head #6 screw into a mounting

hole on the motherboard and its matching mounting hole on the chassis.

7. Repeat Step 5 to insert #6 screws into all mounting holes.

8. Make sure that the motherboard is securely placed in the chassis.

Note: Images displayed are for illustration only. Your chassis or compo-

nents might look different from those shown in this manual.

2-10

A1SAi & A1SRi Series Motherboard User’s Manual

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

2-5 Connectors/IO Ports

The I/O ports are color coded in conformance with the industry standards. See the

gure below for the colors and locations of the various I/O ports.

I/O Back Panel

A

C

B

E

F

D

G

H

I

J

I/O Back Panel

A. COM1 G. LAN1

B. USB Port 2.0-0 H. LAN3

C. USB Port 2.0-1 I. LAN2

D. IPMI LAN J. LAN4

E. USB Port 3.0-0 K. VGA

F. USB Port 3.0-1

K

Chapter 2: Installation

2-11

Ethernet Ports

Four Gigabit Ethernet ports (LAN1/3,

LAN2/4) are located next to the VGA

Connector on the I/O Back panel to

provide network connections. In addi-

tion, a dedicated IPMI LAN, supported

by the BMC controller, is also located

on the I/O panel. These ports accept

RJ45 type cables.

Note: Please refer to the LED

Indicator Section for LAN LED

information.

LAN Ports

Pin Denition

Pin# Denition

1 P2V5SB 10 SGND

2 TD0+ 11 Act LED

3 TD0- 12 P3V3SB

4 TD1+ 13 Link 100 LED

(Green, +3V3SB)

5 TD1- 14 Link 1000 LED

(Yellow, +3V3SB)

6 TD2+ 15 Ground

7 TD2- 16 Ground

8 TD3+ 17 Ground

9 TD3- 88 Ground

(NC: No Connection)

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

A. COM1

B. COM2

C. LAN1

D. LAN3

E LAN2

F. LAN4

G. IPMI

D

C

A

B

E

F

G

Serial Ports

Two COM connections (COM1 &

COM2) are located on the mother-

board. COM1 is located on the Back-

plane I/O panel. COM2, located next to

the Front Control Panel, provides front

access support. See the table on the

right for pin denitions.

Serial COM) Ports

Pin Denitions

Pin # Denition Pin # Denition

1 DCD 6 DSR

2 RXD 7 RTS

3 TXD 8 CTS

4 DTR 9 RI

5 Ground 10 N/A

A

1

5

96

COM2 Pin Layout

2-12

A1SAi & A1SRi Series Motherboard User’s Manual

A. Backpanel USB 2.0 #0

B. Backpanel USB 2.0 #1

C. Backpanel USB 3.0 #0

D. Backpanel USB 3.0 #1

E. USB 3.0 #2 (Internal Header - One

Port Available)

F. USB 3.0 #3 (Type A)

Universal Serial Bus (USB)

Two Universal Serial Bus 2.0 ports (0/1) and two USB 3.0 ports (0/1) are located

on the I/O back panel. The motherboard also has two onboard USB3.0 connections

(USB2/3) to provide additional USB support. USB 3.0 port 2 is from an internal

header, while USB 3.0 port 3 is a Type A connector. (USB cables are not included

in the shipment.) See the tables below for pin denitions.

Back Panel USB-2.0 #0/1

Pin Denitions

Pin# Denition Pin# Denition

1 +5V 5 +5V

2 USB_PN1 6 USB_PN0

3 USB_PP1 7 USB_PP0

4 Ground 8 Ground

Internal USB-3.0 2

Pin Denitions

Pin# Signal Description

1 VBus Power

2 IntA_P1__SSRX- USB3 ICC Port1 SuperSpeed Rx-

3 IntA_P1__SSRX+ USB3 ICC Port1 SuperSpeed Rx+

4 Ground Ground

5 IntA_P1__SSTX- USB3 ICC Port1 SuperSpeed Tx-

6 IntA_P1__SSTX+ USB3 ICC Port1 SuperSpeed Tx+

7 Ground Ground

8 IntA_P1__D- USB3 ICC Port1 D- (USB2 Signal D-)

9 IntA_P1__D+ USB3 ICC Port1 D- (USB2 Signal D2+)

10 Ground Ground

11-19 NC (Not Connected) NC (Not Connected)

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

D

C

A

B

E

F

Chapter 2: Installation

2-13

A

B

VGA

A VGA port is located next to the LAN 2/4 ports

on the I/O back panel. Use this port to connect

to a compatible VGA display.

Unit Identier Switch

A Unit Identier (UID) Switch and two LED

Indicators are located on the motherboard. The

UID Switch is located next to the VGA port on

the back panel. The Rear UID LED (LED7) is

located next to the UID Switch. The Front Panel

UID LED is located at pin 7 of the Front Control

Panel at JF1. Connect a cable to pin 7 on JF1

for Front Panel UID LED indication. When you

press the UID switch, both Rear UID LED and

Front Panel UID LED Indicators will be turned

on. Press the UID switch again to turn off both

LED Indicators. These UID Indicators provide

easy identication of a system unit that may be

in need of service.

Note: UID can also be triggered via

IPMI on the motherboard. For more

information on IPMI, please refer to

the IPMI User's Guide posted on our

website at http://www.supermicro.

com.

UID Switch

Pin# Denition

1 Ground

2 Ground

3 Button In

4 Button In

UID LED

Status

Color/State OS Status

Blue: On Windows OS Unit Identied

Blue:

Blinking

Linux OS Unit Identied

Power Butt

on

OH/Fan Fail/PWR Fail

1

NIC1 Activity LED

Reset Button

2

Power Fail LED

HDD LED

FP PWRLED

Reset

PWR

3.3 V

3.3V Stby

UID LED

Ground

Ground

1920

3.3V

X

Ground

NMI

X

NIC2 Activity LED

3.3V Stby

3.3V Stby

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

A. UID Switch

B. Rear UID LED

C. Front UID LED

D. VGA

D

D

C

2-14

A1SAi & A1SRi Series Motherboard User’s Manual

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

Front Control Panel

JF1 contains header pins for various buttons and indicators that are normally located

on a control panel at the front of the chassis. These connectors are designed spe-

cically for use with Supermicro chassis. See the gure below for the descriptions

of the front control panel buttons and LED indicators. Refer to the following section

for descriptions and pin denitions.

JF1 Header Pins

Power Butt

on

OH/Fan Fail/PWR Fail

1

NIC1 Activity LED

Reset Button

2

Power Fail LED

HDD LED

FP PWRLED

Reset

PWR

3.3 V

3.3V Stby

UID LED

Ground

Ground

1920

3.3V

X

Ground

NMI

X

NIC2 Activity LED

3.3V Stby

3.3V Stby

Chapter 2: Installation

2-15

Power LED

The Power LED connection is located

on pins 15 and 16 of JF1. Refer to the

table on the right for pin denitions.

NMI Button

The non-maskable interrupt button

header is located on pins 19 and 20

of JF1. Refer to the table on the right

for pin denitions.

NMI Button

Pin Denitions (JF1)

Pin# Denition

19 Control

20 Ground

Power LED

Pin Denitions (JF1)

Pin# Denition

15 3.3V

16 PWR LED

Front Control Panel Pin Denitions

Power Button

OH/Fan Fail/PWR Fail

1

NIC1 Activity LED

Reset Button

2

Power Fail LED

HDD LED

FP PWRLED

Reset

PWR

3.3 V

3.3V Stby

UID LED

Ground

Ground

1920

3.3V

X

Ground

NMI

X

NIC2 Activity LED

3.3V Stby

3.3V Stby

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

A. NMI Button

B. PWR LED

A

B

2-16

A1SAi & A1SRi Series Motherboard User’s Manual

Power Butt

on

OH/Fan Fail/PWR Fail

1

NIC1 Activity LED

Reset Button

2

Power Fail LED

HDD LED

FP PWRLED

Reset

PWR

3.3 V

3.3V Stby

UID LED

Ground

Ground

1920

3.3V

X

Ground

NMI

X

NIC2 Activity LED

3.3V Stby

3.3V Stby

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

A. HDD LED

B. NIC1 Activity LED

C. NIC2 Activity LED

A

B

HDD LED

The HDD LED connection is located

on pins 13 and 14 of JF1. Attach a

cable here to indicate the status of

HDD-related activities, including SATA

activities. See the table on the right for

pin denitions.

HDD LED

Pin Denitions (JF1)

Pin# Denition

13 3.3V Standby

14 HD LED

NIC1/NIC2 (LAN1/LAN2)

The NIC (Network Interface Control-

ler) LED connection for LAN port 1

is located on pins 11 and 12 of JF1,

and the LED connection for LAN Port

2 is on pins 9 and 10. NIC1 LED and

NIC2 LED are 2-pin NIC LED head-

ers. Attach NIC LED cables to NIC1

and NIC2 LED indicators to display

network activities. Refer to the table

on the right for pin denitions.

C

NIC1/NIC2 LED

Pin Denitions (JF1)

Pin# Denition

9/11 3.3V

10/12 NIC Activity LED

Chapter 2: Installation

2-17

OH/Fan Fail/PWR Fail/Blue UID

LED Pin Denitions (JF1)

Pin# Denition

7 BLue UID LED

8 OH/Fan Fail/Power Fail Cathode

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

Power Butt

on

OH/Fan Fail/PWR Fail

1

NIC1 Activity LED

Reset Button

2

Power Fail LED

HDD LED

FP PWRLED

Reset

PWR

3.3 V

3.3V Stby

UID LED

Ground

Ground

1920

3.3V

X

Ground

NMI

X

NIC2 Activity LED

3.3V Stby

3.3V Stby

C

A. (Blue) UID LED

B. (Red) OH/Fan Fail/PWR

Fail LED

C. PWR Fail

A

B

Overheat (OH)/Fan Fail/PWR Fail/
UID LED

Connect an LED cable to pins 7 and

8 of Front Control Panel to use the

Overheat/Fan Fail/Power Fail and

UID LED connections. The blue LED

on pin 7 works as the front panel UID

LED indicator. The red LED on pin 8

works provides warnings of overheat,

fan failure or power failure. The red

LED takes precedence over the blue

LED by default. Refer to the table on

the right for pin denitions.

Power Fail LED

The Power Fail LED connection is

located on pins 5 and 6 of JF1. Re-

fer to the table on the right for pin

denitions.

PWR Fail LED

Pin Denitions (JF1)

Pin# Denition

5 3.3V

6 PWR Supply Fail

2-18

A1SAi & A1SRi Series Motherboard User’s Manual

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

Power Button

The Power Button connection is located

on pins 1 and 2 of JF1. Momentarily

contacting both pins will power on/off

the system. This button can also be

configured as 4-Seconds Override or

Instant Off (with a setting in the BIOS -

see Chapter 4). To turn off the power in

the suspend mode, press the button for

at least 4 seconds. Refer to the table on

the right for pin denitions.

Power Button

Pin Denitions (JF1)

Pin# Denition

1 Signal

2 Ground

Reset Button

The Reset Button connection is located

on pins 3 and 4 of JF1. Attach it to a

hardware reset switch on the computer

case to reset the system. Refer to the

table on the right for pin denitions.

Reset Button

Pin Denitions (JF1)

Pin# Denition

3 Reset

4 Ground

A. Reset Button

B. PWR Button

A

B

Power Butt

on

OH/Fan Fail/PWR Fail

1

NIC1 Activity LED

Reset Button

2

Power Fail LED

HDD LED

FP PWRLED

Reset

PWR

3.3 V

3.3V Stby

UID LED

Ground

Ground

1920

3.3V

X

Ground

NMI

X

NIC2 Activity LED

3.3V Stby

3.3V Stby

Chapter 2: Installation

2-19

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

2-6 Connecting Cables

This section provides brief descriptions and pin-out denitions for onboard headers

and connectors. Be sure to use the correct cable for each header or connector.

For information on back panel USB and Front Panel USB ports, refer to age 2-12.

A. 24-Pin ATX PWR

B. 4-Pin 12V DC Alternative

Power Source (up to 144W)

C. 4-Pin HDD PWR

ATX Power 24-pin Connector

Pin Denitions (JPW1)

Pin# Denition Pin # Denition

13 +3.3V 1 +3.3V

14 NC 2 +3.3V

15 COM 3 COM

16 PS_ON 4 +5V

17 COM 5 COM

18 COM 6 +5V

19 COM 7 COM

20 Res (NC) 8 PWR_OK

21 +5V 9 5VSB

22 +5V 10 +12V

23 +5V 11 +12V

24 COM 12 +3.3V

ATX PWR, DC PWR and HDD PWR
Connectors (JPW1, J1, J3)

The 24-pin ATX power connector header

(JPW1) is used to provide power to the

motherboard. The 4-pin DC Power con-

nector, located at J1, provides alternative

12V power source for space-restrained

enclosures such as SC101i when JPW1

is not in use. The 4-pin HDD Power

connector J3 provides power to onboard

HDD devices.

A

Note 1: Do not use the 4-pin

DC power at J1 when the

24-pin ATX Power at JPW1 is

connected to the power supply.

B

C

1

4

2

3

1

4

12V DC Power

Pin Denitions (J1)

Pin# Denition

1-2 GND

3-4 12V

4-Pin HDD Power

Pin Denitions (J3)

Pin# Denition

1 12V

2-3 GND

4 5V

2-20

A1SAi & A1SRi Series Motherboard User’s Manual

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

Fan Header

Pin Denitions

Pin# Denition

1 Ground (Black)

2 3A/+12V (Red)

3 Tachometer

4 PWM_Control

Fan Headers (Fan 1 ~ Fan 3)

The A1SAi & A1SRi Series motherboard has

three 4-pin fan headers (Fan 1~Fan 3). Although

pins 1-3 of the fan headers are backward

compatible with the traditional 3-pin fans, we

recommend to use 4-pin fans to take advan-

tage of the fan speed control via Pulse Width

Modulation through the BMC. This allows the

fan speeds to be automatically adjusted based

on the motherboard temperature. Refer to the

table on the right for pin denitions.

A

B

A. Fan 1

B. Fan 2

C. Fan 3

D. Chassis Intrusion

C

D

Chassis Intrusion (JL1)

A Chassis Intrusion header is located at JL1 on

the motherboard. Attach the appropriate cable

from the chassis to inform you of a chassis intru-

sion when the chassis is opened.

Chassis Intrusion

Pin Denitions (JL1)

Pin# Denition

1 Intrusion Input

2 Ground

Chapter 2: Installation

2-21

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

Internal Buzzer (SP1)

The Internal Buzzer (SP1) can be

used to provide audible indications for

various beep codes. See the table on

the right for pin denitions.

A. Internal Buzzer

B. PWR LED/Speaker Header

Internal Buzzer

Pin Denition

Pin# Denitions

Pin 1 Pos. (+) Beep In

Pin 2 Neg. (-) Alarm

Speaker

A

B

Power LED/Speaker

On JD1 header, pins 1-3 are used for

power LED indication, and pins 4-7

are for the speaker. See the tables

on the right for pin denitions. Please

note that the speaker connector

pins (4-7) are used with an external

speaker. If you wish to use the on-

board speaker, you should close pins

6-7 with a jumper (Default).

Speaker Connector

Pin Settings

Pin Setting Denition

Pins 4-7 External Speaker

Pins 6-7 Internal Speaker (Default)

PWR LED Connector

Pin Denitions

Pin Setting Denition

Pin 1 Anode (+)

Pin2 Cathode (-)

Pin3 NA

2-22

A1SAi & A1SRi Series Motherboard User’s Manual

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

DOM PWR Connector (JSD1)

The Disk-On-Module (DOM) power

connector, located at JSD1, provides

5V power to a solid state DOM storage

device connected to one of the SATA

ports. See the table on the right for

pin denitions.

DOM PWR

Pin Denitions

Pin# Denition

1 5V

2 Ground

3 Ground

A. DOM PWR

B. Overheat LED Header

A

Overheat LED

Pin Denitions

Pin Denition

1 3.3V

2 OH Active

Overheat LED Header

The JOH1 header is used to connect

an LED indicator to provide warnings

of chassis overheating and fan failure.

This LED will blink when a fan failure

occurs. Refer to the tables on right for

pin denitions.

OH/Fan Fail/PWR Fail

LED Status (Red LED)

State Denition

Off Normal

Solid Overheat

Flashing Fan Fail

B

Chapter 2: Installation

2-23

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

A. TPM/Port 80

B. LAN3/LAN4 LED Indication

Header

A

TPM Header/Port 80 Header

A Trusted Platform Module/Port 80

header, located at JTPM1, provides

Trusted Platform (TPM) support and

Port 80 connection. Use this header

to enhance system performance and

data security. See the table on the

right for pin denitions.

TPM/Port 80 Header

Pin Denitions

Pin # Denition Pin # Denition

1 LCLK 2 GND

3 LFRAME# 4 <(KEY)>

5 LRESET# 6 NC

7 LAD 3 8 LAD 2

9 +3.3V 10 LAD1

11 LAD0 12 GND

13 NC 14 NC

15 +3V_DUAL 16 SERIRQ

17 GND 18 Ground

19 LPCPD# 20 NC

LAN3/LAN4 Activity LED Header

The JPK1 header provides LAN3/4

LED activity. LAN1/LAN2 LED indica-

tor connections are located on pins

9/10 and 11/12 of the front control

panel (JF1).

B

JPK1 LAN Activity LED

Pin Denitions

Pin# Denition

1 3.3V Stby

2 LAN4 Activity LED

3 3.3V Stby

4 LAN3 Activity LED

2-24

A1SAi & A1SRi Series Motherboard User’s Manual

Power SMB (I2C) Connector

Power System Management Bus (I2C)

Connector (JPI2C1) monitors power

supply, fan and system temperatures.

See the table on the right for pin

denitions.

PWR SMB

Pin Denitions

Pin# Denition

1 Clock

2 Data

3 PWR Fail

4 Ground

5 NC

System Management Bus Header

A System Management Bus header

for IPMI 2.0 is located at JIPMIB1.

Connect the appropriate cable here

to use the IPMI I2C connection on

your system.

SMBus Header

Pin Denitions

Pin# Denition

1 Data

2 Ground

3 Clock

4 No Connection

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

A. SMBus for IPMI

B. PWR SMBus

A

B

Chapter 2: Installation

2-25

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

2-7 Jumper Settings

Explanation of Jumpers

To modify the operation of the mother-

board, jumpers can be used to choose

between optional settings. Jumpers create

shorts between two pins to change the

function of the connector. Pin 1 is identied

with a square solder pad on the printed

circuit board.

Note: On two-pin jumpers,

"Closed" means the jumper is on,

and "Open" means the jumper is

off the pins.

A. LAN Ports Enable or

Disable

LAN Ports Enable/Disable

Jumper JPL1 enables or disables Ethernet

LAN ports on the motherboard. See the

table on the right for jumper settings. The

default setting is enabled.

GbE LAN Enable

Jumper Settings

Pin# Denition

1-2 Enabled (default)

2-3 Disabled

A

2-26

A1SAi & A1SRi Series Motherboard User’s Manual

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

A. Clear CMOS

B. JI2C1

C. JI2C2

PCI Slot_SMB Enable

Jumper Settings

Jumper Setting Denition

Short Enabled

Open (Default) Disabled

PCI-E Slot SMB Enable (I2C1/I2C2)

Use Jumpers I2C1/I2C2 to enable PCI

SMB (System Management Bus) support

to improve system management for the

onboard PCI-E slot. See the table on the

right for jumper settings.

C

A

B

CMOS Clear

JBT1 is used to clear CMOS. Instead of pins, this "jumper" consists of contact pads

to prevent accidental clearing of CMOS. To clear CMOS, use a metal object such

as a small screwdriver to touch both pads at the same time to short the connec-

tion. Always remove the AC power cord from the system before clearing CMOS.

Note 1: For an ATX power supply, you must completely shut down the

system, remove the AC power cord, and then short JBT1 to clear CMOS.

Note 2: Be sure to remove the onboard CMOS Battery before you short

JBT1 to clear CMOS.

Note 3: Clearing CMOS will also clear all passwords.

Chapter 2: Installation

2-27

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

A

A. Watch Dog Enable

B. VGA Enable

VGA Enable

Jumper JPG1 allows the user to enable the

onboard VGA connector. The default setting

is pins 1-2 to enable the connection. See the

table on the right for jumper settings.

VGA Enable

Jumper Settings

Jumper Setting Denition

Pins 1-2 Enabled (Default)

Pins 2-3 Disabled

B

Watch Dog Timer Enable

Watch Dog (JWD1) is a system monitor that

can be used to reboot the system when a soft-

ware application hangs. Close pins 1-2 to re-

set the system if an application hangs. Close

pins 2-3 to generate a non-maskable interrupt

signal for the application that hangs. See the

table on the right for jumper settings. Watch

Dog must also be enabled in the BIOS.

Watch Dog

Jumper Settings

Jumper Setting Denition

Pins 1-2 Reset (default)

Pins 2-3 NMI

Open Disabled

2-28

A1SAi & A1SRi Series Motherboard User’s Manual

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

A. LAN LEDs

B. IPMI LAN LED

B

2-8 Onboard Indicators

BMC Heartbeat LED

Status

Color/State Denition

Green:Blinking BMC: Normal

A

A

IPMI Dedicated LAN LEDs

In addition to LAN ports, a dedicated IPMI

LAN is also located on the I/O back panel.

The amber LED on the right indicates

connection and activity, while the green

LED on the left indicates the speed of

the connection. See the table at right for

more information.

IPMI LAN

GbE LAN LEDs

There are four GbE LAN ports on the

motherboard. Each Gigabit Ethernet LAN

port has two LEDs. The Yellow LED on

the right indicates connection and activ-

ity. The Link LED on the left side may be

green, amber or off to indicate the speed

of the connection. See the tables on right

for more information.

Activity LED

GbE LAN Link Speed Indicator

LED Settings (Left)

LED Color Denition

Off No Connection. 10 Mbps

Amber 1 Gbps

Green 100 Mbps

Link Speed LED

GbE LAN Activity Indicator (Right)

LED Settings

Color Status Denition

Off No Connections

Yellow Flashing Active

Rear View (when facing the
rear side of the chassis)

Link Speed LED

Activity LED

Chapter 2: Installation

2-29

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

A

B

A. PWR LED

B. OH/PWR Fail/Fan Fail

LED

Overheat/PWR Fail/Fan Fail LED

An onboard Overheat/PWR Fail/ Fan Fail LED

is located at LED8. See the table on the right

for more information.

Onboard Power LED

An Onboard Power LED is located at

LED3 on the motherboard. When this

LED is on, the system is on. Be sure to

turn off the system and unplug the power

cord before removing or installing compo-

nents. See the table on the right for more

information.

Onboard PWR LED Indicator

LED Settings

LED Color Denition

Off System Off (PWR cable

not connected)

Green System On

Green:
Flashing

Quickly

ACPI S1 State

OverHeat/PWR Fail/Fan Fail

LED Status

Color/State Denition

Solid Overheat

Blinking PWR Fail or Fan Fail

2-30

A1SAi & A1SRi Series Motherboard User’s Manual

Unit Identication LED

A rear UID LED indicator (LED7) is located

next to the Unit Identier (UID) switch on the

I/O backplane. The front panel UID LED is

located at pin 7 of the Front Control Panel at

JF1. Connect a cable to pin 7 on JF1 for front

panel UID LED indication. When you press

the UID switch, both rear UID LED and front

panel UID LED Indicators will be turned on.

Press the UID switch again to turn off both

LED Indicators. These UID Indicators provide

easy identication of a system unit that may

be in need of service.

Note: UID can also be triggered via

IPMI on the motherboard. For more

information on IPMI, please refer to

the IPMI User's Guide posted on

our website at http://www.supermi-

cro.com.

UID LED Status

Color/State OS Status

Blue: On Windows OS Unit Identied

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

A. UID LED

A

Chapter 2: Installation

2-31

Battery

JD1

FAN1

FAN2

FAN3

I-SATA4

I-SATA5

J1

J3

JPI2C1

JPW1

JSD1

JTPM1

VGA

LED8

LED3

LED7

JBT1

1

JOH1

JL1

JI2C1

JI2C2

JPK1

JWD1

JPG1

JIPMB1

COM2

COM1

JF1

USB 3.0-2

LAN3/4 LED

LAN2/LAN4

LAN1/LAN3

USB2.0-0/1

USB3.0-0/1

USB 3.0-3

IPMI_LAN

PCI-E 2.0 X8

DIMMA1

DIMMA2

DIMMB2

DIMMB1

I-SATA0

A1SAi/A1SRi Series Motherboard

Rev. 1.00

FP CTRL

JPL1

BIOS

Marvell
PHY

BMC

Bar Code

JUIDB1

CPU

SP1

I-SATA2

I-SATA3

I-SATA1

LED2

2-9 SATA Connections

A. I-SATA 3.0 #0

B. I-SATA 3.0 #1

C. I-SATA 2.0 #2

D. I-SATA 2.0 #3

E. I-SATA 2.0 #4

F. I-SATA 2.0 #5

D

E

F

C

A

B

Serial ATA

Pin Denitions

Pin# Denition

1 Ground

2 TX_P

3 TX_N

4 Ground

5 RX_N

6 RX_P

7 Ground

Serial ATA Ports

There are up to six Serial ATA ports on

the motherboard. I-SATA0/1 support SATA

3.0 connections. I-SATA2~5 are SATA 2.0

ports. These ports provide serial-link signal

connections, which are faster than the con-

nections of Parallel ATA. See the table on

the right for pin denitions.

Note: I-SATA4/5 are not available

on the A1SRi-2358F.

2-32

A1SAi & A1SRi Series Motherboard User’s Manual

Notes

3-1

Chapter 3: Troubleshooting

Chapter 3

Troubleshooting

3-1 Troubleshooting Procedures

Use the following procedures to troubleshoot your system. If you have followed all

of the procedures below and still need assistance, refer to the ‘Technical Support

Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter.

Always disconnect the AC power cord before adding, changing or installing any

hardware components.

Before Power On

1. Make sure that the Standby PWR LED is not on. (Note: If it is on, the onboard

power is on. Be sure to unplug the power cable before installing or removing

the components.)

2. Make sure that there are no short circuits between the motherboard and chassis.

3. Disconnect all ribbon/wire cables from the motherboard, including those for the

keyboard and mouse. Also, be sure to remove all add-on cards.

No Power

1. Make sure that there are no short circuits between the motherboard and chassis.

2. Make sure that all jumpers are set to their default positions.

3. Check if the 115V/230V switch on the power supply is properly set.

4. Turn the power switch on and off to test the system.

5. The battery on your motherboard may be old. Check to make sure that it still

supplies ~3VDC. If it does not, replace it with a new one.

No Video

1. If the power is on, but you have no video, you will need to remove all the add-

on cards and cables rst.

3-2

A1SAi & A1SRi Series Motherboard User’s Manual

2. Use the speaker to determine if any beep codes exist. (Refer to Appendix A for

details on beep codes.)

3. Remove all memory modules and turn on the system. (If the alarm is on, check

the specications of memory modules, reset the memory or try a different one.)

Memory Errors

1. Make sure that the DIMM modules are properly installed and fully seated in

the slots.

2. You should be using unbuffered ECC DDR3 SODIMM (1.5V, 1.35V) 1600/1333

MHz memory recommended by the manufacturer. Also, it is required that you

use the memory modules of the same type and speed for all DIMMs in the

system. Do not use memory modules of different sizes, speeds, or types on the

motherboard. Some 1600MHz memory can be used on A1SRi-2358F, but they

will operate at 1333MHz only.

3. Check for bad DIMM modules or slots by swapping modules between slots to

see if you can locate the faulty ones.

4. Check the switch of 115V/230V power supply.

5. 16GB 1600MHz modules will require BIOS version 1.1a or newer to work. If

you have an older BIOS, please use other modules to boot up the motherboard

in order to update the BIOS or submit an RMA to send back to Supermicro for

the update.

Losing the System’s Setup Conguration

1. Please be sure to use a high quality power supply. A poor quality power supply

may cause the system to lose CMOS setup information. Refer to Section 1-6

for details on recommended power supplies.

2. The battery on your motherboard may be old. Check to verify that it still sup-

plies ~3VDC. If it does not, replace it with a new one.

3. If the above steps do not x the Setup Conguration problem, contact your

vendor for repairs.

3-3

Chapter 3: Troubleshooting

3-2 Technical Support Procedures

Before contacting Technical Support, please make sure that you have followed all

the steps listed below. Also, Note that as a motherboard manufacturer, Supermicro

does not sell directly to end users, so it is best to rst check with your distributor or

reseller for troubleshooting services. They should know of any possible problem(s)

with the specic system conguration that was sold to you.

1. Please go through the ‘Troubleshooting Procedures’ and 'Frequently Asked

Question' (FAQ) sections in this chapter or see the FAQs on our website (http://

www.supermicro.com/support/faqs/) before contacting Technical Support.

2. BIOS upgrades can be downloaded from our website at (http://www.supermicro.

com/support/bios/).

Note: Not all BIOS can be ashed. Some cannot be ashed; it depends

on the boot block code of the BIOS.

3. If you've followed the instructions above to troubleshoot your system, and still

cannot resolve the problem, then contact Supermicro's technical support and

provide them with the following information:

• Motherboard model and PCB revision number

• BIOS release date/version (this can be seen on the initial display when your

system rst boots up)

• System conguration

• An example of a Technical Support form is on our website at (http://www.super-

micro.com/RmaForm/).

4. Distributors: For immediate assistance, please have your account number

ready when placing a call to our technical support department. We can be

reached by e-mail at [e-mail], by phone at: [phone],

option 2, or by fax at [phone].

3-4

A1SAi & A1SRi Series Motherboard User’s Manual

3-3 Frequently Asked Questions

Question: What type of memory does my motherboard support?

Answer: The A1SAi & A1SRi Series motherboard supports up to 64GB of Unbuf-

fered ECC DDR3 SODIMM (1.5V, 1.35V, 1600/1333 MHz). The A1SRi-2358F sup-

ports up to 16GB. See Section 2-3 for details on installing memory.

Question: I am using 16GB 1600MHz memory modules. My motherboard does not

boot past the Supermicro POST screen. What is the problem?

Answer: 16GB 1600MHz modules will require BIOS version 1.1a or newer to work.

Your motherboard might be on an older BIOS. Please use other modules in order

to boot up the motherboard and update the BIOS or submit an RMA to send back

to Supermicro for the update.

Question: How do I update my BIOS?

Answer: We do NOT recommend that you upgrade your BIOS if you are not

experiencing any problems with your system. Updated BIOS les are located on

our website at http://www.supermicro.com/support/bios/. Please check our BIOS

warning message and the information on how to update your BIOS on our web

site. Select your motherboard model and download the BIOS ROM le to your

computer. Also, check the current BIOS revision to make sure that it is newer than

your BIOS before downloading. You may choose the zip le or the .exe le. If you

choose the zipped BIOS le, please unzip the BIOS le onto a bootable device or

a USB pen/thumb drive. To ash the BIOS, run the batch le named "ash.bat"

with the new BIOS ROM le from your bootable device or USB pen/thumb drive.

Use the following format:

F:\> ash.bat BIOS-ROM-lename.xxx <Enter>

Note: Always use the le named “ash.bat” to update the BIOS, and

insert a space between "ash.bat" and the BIOS ROM image le name.

Warning: Do not shut down or reset the system while updating the BIOS to prevent

possible system boot failure!

Important: The SPI BIOS chip installed on this motherboard is not re-

movable. To repair or replace a damaged BIOS chip, please send your

motherboard to RMA at Supermicro for service.

3-5

Chapter 3: Troubleshooting

3-4 Battery Removal and Installation

Battery Removal

To remove the onboard battery, follow the steps below:

1. Power off your system and unplug your power cable.

2. Locate the onboard battery as shown below.

3. Using a tool such as a pen or a small screwdriver, push the battery lock out-

wards to unlock it. Once unlocked, the battery will pop out from the holder.

4. Remove the battery.

Proper Battery Disposal

Warning: Please handle used batteries carefully. Do not damage the battery in any

way; a damaged battery may release hazardous materials into the environment. Do

not discard a used battery in the garbage or a public landll. Please comply with the

regulations set up by your local hazardous waste management agency to dispose of

your used battery properly.

Battery Installation

1. To install an onboard battery, follow the steps 1 & 2 above and continue

below:

2. Identify the battery's polarity. The positive (+) side should be facing up.

3. Insert the battery into the battery holder and push it down until you hear a

click to ensure that the battery is securely locked.

Warning: When replacing a battery, be sure to only replace it with the same type.

OR

3-6

A1SAi & A1SRi Series Motherboard User’s Manual

3-5 Returning Merchandise for Service

A receipt or copy of your invoice marked with the date of purchase is required

before any warranty service will be rendered. You can obtain service by calling

your vendor for a Returned Merchandise Authorization (RMA) number. For faster

service, you may also obtain RMA authorizations online (http://www.supermicro.

com/RmaForm/). When you return the motherboard to the manufacturer, the RMA

number should be prominently displayed on the outside of the shipping carton, and

mailed prepaid or hand-carried. Shipping and handling charges will be applied for

all orders that must be mailed when service is complete.

This warranty only covers normal consumer use and does not cover damages

incurred in shipping or from failure due to the alteration, misuse, abuse or improper

maintenance of products.

During the warranty period, contact your distributor rst for any product problems.

Chapter 4: AMI BIOS

4-1

Chapter 4

BIOS

4-1 Introduction

This chapter describes the AMI BIOS setup utility for the A1SAi & A1SRi Series

motherboard. The ROM BIOS is stored in a Flash EEPROM and can be easily

updated. This chapter describes the basic navigation of the AMI BIOS setup utility

setup screens.

Note: For A1SAi & A1SRi BIOS recovery, please use special recovery

BIOS image AMI.ROM and special procedure based on FAQ 21047 when

recovery is needed.

Starting BIOS Setup Utility

To enter the AMI BIOS setup utility screens, press the <Delete> key while the

system is booting up.

Note: In most cases, the <Delete> key is used to invoke the AMI BIOS

setup screen. There are a few cases when other keys are used, such as

<F1>, <F2>, etc.

Each main BIOS menu option is described in this manual. The Main BIOS setup

menu screen has two main frames. The left frame displays all the options that can

be congured. Grayed-out options cannot be congured. Options in blue can be

congured by the user. The right frame displays the key legend. Above the key

legend is an area reserved for a text message. When an option is selected in the

left frame, it is highlighted in white. Often a text message will accompany it. (Note:

the AMI BIOS has default text messages built in. Supermicro retains the option to

include, omit, or change any of these text messages.)

The AMI BIOS setup utility uses a key-based navigation system called "hot keys".

Most of the AMI BIOS setup utility "hot keys" can be used at any time during the

setup navigation process. These keys include <F1>, <F4>, <Enter>, <ESC>, arrow

keys, etc.

Note: Options printed in Bold are default settings.

4-2

A1SAi & A1SRi Series Motherboard User’s Manual

How To Change the Conguration Data

The conguration data that determines the system parameters may be changed by

entering the AMI BIOS setup utility. This setup utility can be accessed by pressing

<Del> at the appropriate time during system boot.

How to Start the Setup Utility

Normally, the only visible Power-On Self-Test (POST) routine is the memory test.

As the memory is being tested, press the <Delete> key to enter the main menu of

the AMI BIOS setup utility. From the main menu, you can access the other setup

screens. An AMI BIOS identication string is displayed at the left bottom corner of

the screen, below the copyright message.

Warning: Do not update the BIOS unless your system has a BIOS-related issue.

Flashing the wrong BIOS can cause irreparable damage to the system. In no event

shall Supermicro be liable for direct, indirect, special, incidental, or consequential dam-

ages arising from a BIOS update. If you have to update the BIOS, do not shut down

or reset the system while the BIOS is updating. This is to avoid possible boot failure.

Chapter 4: AMI BIOS

4-3

4-2 Main Setup

When you rst enter the AMI BIOS setup utility, you will enter the Main setup screen.

You can always return to the Main setup screen by selecting the Main tab on the

top of the screen. The Main BIOS Setup screen is shown below.

The following Main menu items will display:

System Date/System Time

Use this feature to change the system date and time. Highlight System Date or

System Time using the arrow keys. Enter new values using the keyboard. Press

the <Tab> key or the arrow keys to move between elds. The date must be entered

in MM/DD/YY format. The time is entered in HH:MM:SS format.

Note: The time is in the 24-hour format. For example, 5:30 P.M. appears

as 17:30:00.

The following BIOS items will also be displayed:

Supermicro A1SRi-2358F

Version

Build Date

Memory Information

Total Memory

This displays the total size of memory available in the system.

4-4

A1SAi & A1SRi Series Motherboard User’s Manual

4-3 Advanced Setup Congurations

Use the arrow keys to select Boot Setup and press <Enter> to access the submenu

items.

Warning: Take Caution when changing the Advanced settings. An incorrect value, a

very high DRAM frequency, or an incorrect DRAM timing setting may make the system

unstable. When this occurs, revert to the default to the manufacture default settings.

Boot Feature

Quiet Boot

Use this feature to select the screen display between the POST messages and the

OEM logo upon bootup. Select Disabled to display the POST messages. Select

Enabled to display the OEM logo instead of the normal POST messages. The op-

tions are Disabled and Enabled.

CSM Support

Select Enabled to support the EFI Compatibility Support Module (CSM), which

provides compatibility support for traditional legacy BIOS for system boot. The op-

tions are Enabled and Disabled.

AddOn ROM Display Mode

Use this feature to set the display mode for the Option ROM. Select Keep Current to

display the current AddOn ROM setting. Select Force BIOS to use the Option ROM

display set by the system BIOS. The options are Force BIOS and Keep Current.

Chapter 4: AMI BIOS

4-5

Bootup Num-Lock

Use this feature to set the Power-on state for the <Numlock> key. The options

are On and Off.

Wait For 'F1' If Error

Use this feature to force the system to wait until the 'F1' key is pressed if an error

occurs. The options are Disabled and Enabled.

Interrupt 19 Capture

Interrupt 19 is the software interrupt that handles the boot disk function. When this

item is set to Enabled, the ROM BIOS of the host adaptors will "capture" Interrupt

19 at bootup and allow the drives that are attached to these host adaptors to func-

tion as bootable disks. If this item is set to Disabled, the ROM BIOS of the host

adaptors will not capture Interrupt 19, and the drives attached to these adaptors

will not function as bootable devices. The options are Immediately and Postponed.

Power Conguration

Watch Dog Function

If enabled, the Watch Dog Timer will allow the system to reboot when it is inactive

for more than 5 minutes. The options are Disabled and Enabled.

Power Button Function

This feature controls how the system shuts down when the power button is pressed.

Select 4 Seconds Override for the user to power off the system after pressing and

holding the power button for 4 seconds or longer. Select Instant Off to instantly

power off the system as soon as the user presses the power button. The options

are Instant Off and 4 Seconds Override.

Restore on AC Power Loss

Use this feature to set the power state after a power outage. Select Stay Off for the

system power to remain off after a power loss. Select Power On for the system

power to be turned on after a power loss. Select Last State to allow the system

to resume its last power state before a power loss. The options are Power On,

Stay Off, and Last State.

WOL (Wake-On LAN) Support

Select Enabled to enable WOL support which will allow the system to "wake-up"

when a device connected to a LAN port receives a signal. The options are Dis-

abled and Enabled.

4-6

A1SAi & A1SRi Series Motherboard User’s Manual

HDD Frozen

Set this feature to enable the HDD Security Frozen Mode. The options are Dis-

abled and Enabled.

CPU Conguration

The following CPU information will be displayed:

• Processor Frequency

• L1 Cache RAM

• L2 Cache RAM

• Processor Version

• MSR 610 PKG_TURBO_PWR_LIM

• MSR 606 PKG_TURBO_SKU_UNIT

Clock Spread Spectrum

If this feature is set to Enabled, the BIOS utility will monitor the level of Electro-

magnetic Interference caused by the components and will attempt to reduce the

interference whenever needed. The options are Disabled and Enabled.

EIST (GV3)

EIST (Enhanced Intel® SpeedStep Technology) GV3 allows the system to automati-

cally adjust processor voltage and core frequency in an effort to reduce power

consumption and heat dissipation. Select Auto to enable 80 CPU stepping support

automatically and disabled other functions. The options are Disable, Enable, and

Auto. Please refer to the Intel website for detailed information.

P-state Coordination

This feature selects the type of coordination for the P-State of the processor. P-

State is a processor operational state that reduces the processor's voltage and

frequency to enhance CPU energy efciency. The options are Hardware, Package,

and Module.

TM1 (Available when supported by the CPU.)

Select Enable to activate TM1 support for system thermal monitoring. TM1 allows

the CPU to regulate its power consumption based upon the modulation of the

CPU Internal clock when the CPU temperature reaches a pre-dened overheating

threshold. The options are Disable and Enable.

Chapter 4: AMI BIOS

4-7

TM2 Mode (Available when supported by the CPU.)

Use this feature to select the throttling mode for TM2. The options are LFM Throt-

tling and Adaptive Throttling.

CPU C State

C-States architecture, a processor power management platform developed by

Intel, can further reduce power consumption from the basic C1 (Halt State) state

that blocks clock cycles to the CPU. Select Enabled for CPU C-Sates support. The

options are Disable, Enable, and Auto.

If CPU C State is set to Enable or Auto, the following three items will be avail-

able for conguration:

Enhanced Halt State (C1E) (Available when "CPU C-States" is set to
Enabled)

Select Enabled to support Enhanced C1 Power State to boost system performance.

Please reboot the system for the new setting to take effect. The options are Dis-

able and Enable.

ACPI C2 (Available when "CPU C-States" is set to Enabled)

Select Enabled for ACPI C2 support to determine how the processor will report the

CPU-C state to the operating system. The options are Disable, C6 NS, and C6 FS.

Monitor/Mwait

Select Enabled to implement the Mwait instruction along with the Monitor instruc-

tion to allow the processor to specify the location for the BIOS to monitor activities

and to issue the instruction to put the operation on hold (Mwait). The options are

Disable and Enable.

L1 Prefetcher (Available when supported by the CPU)

If enabled, the hardware prefetcher will prefetch streams of data and instructions

from the main memory to the L1 cache to improve CPU performance. The options

are Enable and Disable.

L2 Prefetcher (Available when supported by the CPU)

If enabled, the hardware prefetcher will prefetch streams of data and instructions

from the main memory to the L2 cache to improve CPU performance. The options

are Enable and Disable.

ACPI 3.0 T-States (Available when "CPU C-States" is set to Enabled)

Select Enabled to support ACPI (Advanced Conguration and Power Interface) 3.0

T-States to determine how the processor will report to the operating system during

CPU-Throttling states. The options are Disable and Enable.

4-8

A1SAi & A1SRi Series Motherboard User’s Manual

Fast String

Select Enabled to enable Fast String support for REP MOVS/STOS, which will carry

out Repeat-String Operation instructions to move a string of commands to another

location (MOVS) or to add a string of commands to an existing instruction code

(STOS). The options are Disable and Enable.

Machine Check

Select Enabled to use Intel's machine check mechanism to detect and report hard-

ware (machine) errors. The options are Disable and Enable.

Execute Disable Bit (Available if supported by the OS & the CPU)

Set to Enabled to enable the Execute Disable Bit which will allow the processor

to designate areas in the system memory where an application code can execute

and where it cannot, thus preventing a worm or a virus from ooding illegal codes

to overwhelm the processor and damage the system during an attack. The default

is Enable. (Refer to Intel and Microsoft websites for more information.)

VMX (Available when supported by the CPU)

Select Enabled to enable Intel® Vanderpool Technology support which will allow

one platform to run multiple operating systems and applications in independent

partitions, creating multiple "virtual" systems in one physical computer. The options

are Disable and Enable.

BIST Selection (Available when supported by the CPU)

Select Enabled to set a BIST (Built-In-Self-Test) point selection to enhance system

performance. The options are Disable and Enable.

MTRR (Memory Type Range Register) Default as Uncacheable

If this feature is set to Enabled, the default setting will be set to "Uncacheable" in

the Memory-Type-Range Table to protect the data stored in the MTRR table from

being cached. The options are Disable and Enable.

Extended APIC

Select Enabled to enable Extended APIC (Advanced Programmable Interrupt Con-

trol) support to enhance power management. The options are Disable and Enable.

AES-NI

Select Enabled to use the Advanced Encryption Standard in the processor. The

options are Disable and Enable.

Chapter 4: AMI BIOS

4-9

PECI Enable

Select Enabled to enable PECI (Platform Environment Control Interface) support,

which will enhance CPU thermal management to achieve power efciency. The

options are Enable and Disable.

PECI Trusted

Select Enabled to support Trusted Platform Environment Control Interface to im-

prove CPU thermal management. The options are Disable and Enable.

PECI SMBus Speed

Use this feature to set the speed for the physical bus to operate. The options are

Standard (80 kHz), Standard (100 kHz), Fast Mode (400 kHz), and Fast Mode

Plus (1 MHz).

Turbo (Available if Intel EIST technology is Enabled)

This feature allows processor cores to run faster than marked frequency in specic

conditions. The options are Disable and Enable.

RAPL

Select Enabled to enable RAPL (Running Average Power Limit) support. Use the

keyboard to enter your default setting.

MSR 670 PKG_TURBO_CFG1

Use this feature to specify various parameters of system components such as Turbo,

Minimum Energy, SoC TDP Policy, ICMax Control, and Turbo Mode.

MSR 672_TURBO_WKLD_CFG2

Use this feature to specify ICCMax Throttle Ratio for C6 Exits when the value of

PKG_TURBO_CFG1 [4:3] equals to 10Y.

Active Processor Cores

This feature determines how many CPU cores will be activated for each CPU. When

all is selected, all cores in the CPU will be activated. (Please refer to the Intel web

site for more information.) The options are All, 4, and 2.

CPU Flex Ratio Override

Select Enabled to support CPU Flex Ratio Programming. The options are Disable

and Enable.

CPU Core Ratio

Use this feature to set the CPU Core Ratio when CPU Flex Ratio Override is set

to Enabled. Use the keyboard to enter the desired value for the CPU core ratio.

4-10

A1SAi & A1SRi Series Motherboard User’s Manual

Chipset Conguration

Warning: Setting the wrong values in the following features may cause the system

to malfunction.

North Bridge

The following information will be displayed:

• Memory Information

• Total Memory

• Memory Frequency

Pass Gate Setup

Use the following items to congure Pass Gate settings and tests.

Pass Gate Feature Enable

Select Enabled to support Pass Gate features. The options are Disabled and

Enabled.

2x Refresh Rate

Select Enabled to force the BIOS setup utility to use the x2 refresh rate in

Pass-Gate operation regardless the temperatures of the processor and the

motherboard. Refresh Rate is the total number of rows needed to refresh the

entire DRAM array. x2 Refresh Rate will take 2000 rows of memory to refresh

the entire DRAM array. The options are Disabled and Enabled.

Pass Gate Stress Test Conguration

Pass Gate Test

Select Enabled to use the Pass Gate test. The options are Disabled and En-

abled.

Pass Gate Refresh

Use this feature to enable a refresh period during the pass gate test. The options

are Disabled and Enabled.

Pass Gate Test Direction

This feature species how the BIOS setup utility should perform the Pass Gate

test (from the lowest memory to the highest or from the highest memory to the

lowest.) The options are Auto, Lowest to Highest, and Highest to Lowest.

Chapter 4: AMI BIOS

4-11

Pass Gate Test Repetition

Use this feature to specify how many times the Pass Gate test should be per-

formed over the same memory row (x1000). The default setting is 900.

Pass Gate Test Iterations

Use this feature to specify how many repetitions the Pass Gate test should be

performed over the same memory row (refer to the item above). The default

setting is 1.

Pass Gate Test Swizzle (For Samsung Products)

Select Enabled to use the Pass Gate Test Swizzle mode to support Samsung

products. Select Auto for the system to automatically switch to the Pass Gate

Test Swizzle mode when a Samsung device is detected. The options are Auto

and Enabled.

Pass Gate Pattern

Use the keyboard to enter the parameter value of the Pass Gate Pattern used

for data input. The options are 0's and 1's.

Pass Gate Target Pattern

Use the keyboard to enter the target parameter value for the Pass Gate Pattern

used for data input. The options are 0's and 1's.

Pass Gate Speed

Use this feature to set the Pass Gate speed. The options are Auto and 1x Only.

Channel 0/Channel 1

Rank 0/Rank 1/Rank 2/Rank 3

Select Enabled to allow the Pass Gate test to be performed on a memory module

specied by the user. The options are Disabled and Enabled.

Pass Gate MonteCarlo

Select Enabled to enable a algorithm search to nd the maximum value of the

Pass Gate test. The options are Disabled and Enabled.

If Pass Gate MonteCarlo is set to Enabled, the following three items are avail-

able for conguration:

Pass Gate Maximum Failures

Use this feature to specify the maximum number that Pass Gate failures will be

counted for. Use the keyboard to enter the desired value.

4-12

A1SAi & A1SRi Series Motherboard User’s Manual

Pass Gate Maximum Repetition

Use this feature to specify the maximum number that the Pass Gate tests will

be repeated. Use the keyboard to enter the desired value.

Pass Gate Minimum Repetition

Use this feature to specify the minimum number that the Pass Gate tests will be

repeated. Use the keyboard to enter the desired value.

Fast Boot

Select Enabled to skip the routine memory procedure and attempt to boot the

system using the last valid memory conguration settings at bootup. The options

are Disabled and Enabled.

Smm Size (MB)

Use the keyboard to enter a value for the size of the SMM/TSEG region where 1

MB is aligned to. The options are 2, 4, 8, and 16.

Force Memory Map Ax

Select Enabled to force the BIOS setup utility to specify the total number of Kb (or

an error) of memory errors detected by the BIOS upon OS initialization. The options

are Auto and Enabled.

Memory Frequency

This feature sets the memory frequency limits for the DIMM modules installed on the

the motherboard. The options are Auto, DDR3-1333 (MHz), and DDR3-1600 (MHz).

Memory Channels

Use this feature to congure the settings for memory channels. The options are

Auto and Single Channel.

MRC (Maximal Ratio Combining) Debug Messages

Use this feature to set the debug output display in MRC. The options are Disabled,

Minimum, Medium, and Maximum.

DDR Voltage

Use this feature to set the DDR3 voltage setting. The default option is Auto, 1.25V,

1.35V, and 1.50V.

Fine DDR Voltage

Use this feature to set the ne DDR3 voltage setting. Use the "+" or "-" keys to

set the value.

Chapter 4: AMI BIOS

4-13

MMIO High

Use this feature to select the high memory size according to memory-address

mapping for the IO hub. The options are Auto, 256MB, 512MB, 1024MB, 2048MB,

4096MB, and 8192MB.

CKE Power Down

Select Enabled to enable CKE Power Down support which controls the low power

mode for RAM in the active power standby mode. The options are Disabled and

Enabled.

ECC (Error Correctable Correction) Support

Select Enabled to enable ECC support. The options are Disabled and Enabled.

Faulty Part Tracking

Select Enabled to support faulty part tracking for the system to keep track of faulty

memory parts. The options are Disabled and Enabled.

If Faulty Part Tracking is set to Enabled, the item below is available for con-

guration:

On Correctable Faulty Part

Use this feature to set the system to halt or continue on a correctable faulty memory

part. The options are Halt and Continue.

Patrol Scrub Enable

Patrol Scrubbing is a process that allows the CPU to correct correctable memory

errors detected on a memory module and send the correction to the requestor

(the original source). When this item is set to Enabled, North Bridge will read and

write back one cache line every 16K cycles, if there is no delay caused by internal

processing. By using this method, roughly 64 GB of memory behind North Bridge

will be scrubbed every day. The options are Disabled and Enabled.

Patrol Scrub Period

Use this item to specify how often Patrol Scrubbing should be performed. Select 24

hours to allow Patrol Scrubbing to be performed every 24 hours. The options are

24 hours, 10 hours, 4 hours, and 1 hour.

Demand Scrub Enable

Demand Scrubbing is a process that allows the CPU to correct correctable memory

errors found on a memory module. When the CPU or I/O issues a demand-read

command, and the read data from memory turns out to be a correctable error, the

error will be corrected and sent to the requestor (the original source). Memory will

be updated at the same time. Select Enabled to use Demand Scrubbing for ECC

memory correction. The options are Disabled and Enabled.

4-14

A1SAi & A1SRi Series Motherboard User’s Manual

AB Segments In DRAM

When this feature is set to Enabled, Target A- or B- segments will be routed to DRAM

during memory read and write cycles. The options are Disabled and Enabled.

E Segment In DRAM

When this feature is set to Enabled, Target E segment will be routed to DRAM during

memory read and write cycles. The options are Disabled and Enabled.

F Segment In DRAM

When this feature is set to Enabled, Target F segment will be routed to DRAM during

memory read and write cycles. The options are Disabled and Enabled.

ZQ Calibration

When this feature is set to Enabled, commands to calibrate DRAM output drivers

will be issued so that ZQ Calibration will be performed during a system boot or

system reset. The options are Disabled and Enabled.

Propogate Errors to Cores (BMCMODE)

Use this feature to congure the Bunit Machine Check Mode to propogate errors.

The options are Enable and Disable.

CMD Rate (Command Rate)

Use this feature to set the CMD rate, which is the number of clock cycles needed

for the memory to send data. The options are Auto, 1N, 2N, and 3N.

Out of Order Memory Processing

Select Enabled to support Out of Order Memory Processing, which is a process used

by a computer to retrieve instructions from its memory to improve CPU performance.

The options are Disabled and Enabled.

Out of Order Aging Threshold

In a multi-core architecture, the DRAM system in a computer processes multiple

threads or streams of requests from the In_Order (FIFO: First_In_First_Out) queue

and the Out_of_Order queue in the interleaved/interconnect mode. This feature

allows the user to specify the maximum number of requests to be processed for

the same order before the system moves on and process the next thread of re-

quests in the "Out_Of_Order" queue while in the "Out_of_Order" cycle. Once the

"Out_of_Order" cycle expires, the system will move to the "In_Order" cycle and

starts to process the requests in the "In-Order" queue. The default setting is 31.

New Request Bypass

Select Enabled for the system to skip the process currently in progress and process

a new request immediately. The options are Disabled and Enabled.

Chapter 4: AMI BIOS

4-15

Dynamic Self Refresh

Select Enabled to support Dynamic Self-Refreshing for the onboard memory control-

ler. The options are Disabled and Enabled.

PMOP Value for PCO

Use the keyboard to enter the Opcode value for the SPID Power Mode. The default

setting is 4.

PMOP Value for PCX

Use the keyboard to enter the PCX value for the SPID Power Mode. The default

setting is 7.

Per-Bit Margins

Select Enabled to set the "per-bit margins" used in the Maximal Ratio Combining

(MRC) technique. The options are Disabled and Enabled.

Open Page Policy Timer

Use the feature to set the Page_Closure timer, which will specify how long a DRAM

memory page should remain open. The options are Disabled, Immediate, 30-60 ns,

.60-120 ns, 120-240 ns, 240-480 ns, 480-960 ns, and 1-2 us.

Memory Thermal

Select Enabled to support Memory-Thermal-Management. The options are Dis-

abled and Enabled.

Scrambler

Select Enabled to enable memory scrambler support for memory error correction.

The options are Disabled and Enabled.

Slow Power Down Exit

Select Enabled to use the slow-power-down mode when the system memory exits

from the pre-charge state. The settings are Disabled and Enabled.

Verf Override Enable

Select Enabled to verify an override command before it is executed. The options

are Disabled and Enabled.

Timing Conguration

tCL

Use this feature to select the Cas Latency Range. The options are Auto, 5, 6,

7, 8, 9, 10, 11, 12, 13, 14, and 15.

4-16

A1SAi & A1SRi Series Motherboard User’s Manual

tRCD

Use this feature select the Row to Col Delay Range. The options are Auto, 5,

6, 7, 8, 9, 10, 11, 12, 13, 14, and 15.

tRP

Use this feature to select the Ras Precharge Range. The options are Auto, 5,

6, 7, 8, 9, 10, 11, 12, 13, 14, and 15.

tRAS

Use this feature select the Ras Active Time. The options are Auto, 14, 15, 16,

17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, and 34.

tRTP

Use this feature to select the Internal Read to Precharge Command Delay Time.

The options are Auto, 4, 5, 6, and 7.

tRRD

Use this feature to select the Minimum Row Active To Row Active Delay Time.

The options are Auto, 4, 5, 6, and 7.

tFAW

Use this feature to select the Minimum Four Activate Window Delay Time. The

options are Auto, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31,

32, 33, 34, 35, and 36.

tCCD

Use this feature to select the minimum amount of time between column opera-

tions. The options are Auto, 4, 12, and 18.

tWTP

Use this feature to select the Write to PreCharge Time. The options are Auto,

15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, and 30.

tWCL

Use this feature to select the Write CAS Number. The options are Auto, 5, 6,

7, 8, and 9.

South Bridge



USB Conguration

This submenu displays the following sub-items:

Chapter 4: AMI BIOS

4-17

• USB Module Version

• USB Devices

Legacy USB Support

This feature enables support for legacy USB devices. Select Auto to disable

legacy support if USB devices are not present. Select Disable to have USB

devices available only for EFI applications. The options are Enabled, Disabled

and Auto.

XHCI Hand-Off

This item is a work-around solution for operating systems that do not support

XHCI (Extensible Host Controller Interface) hand-off. The XHCI ownership

change should be claimed by the XHCI driver. The options are Enabled and

Disabled.

EHCI Hand-Off

This item is for the Operating Systems that do not support Enhanced Host

Controller Interface (EHCI) hand-off. When this item is enabled, EHCI owner-

ship change will be claimed by the EHCI driver. The settings are Disabled and

Enabled.

USB Mass Storage Driver Support

Select Enabled for USB Mass Storage Driver support. The options are Enabled

and Disabled.

Port 60/64 Emulation

This feature enables or disables I/O port 60h/64h emulation support. This fea-

ture should be enabled for complete USB keyboard legacy support for operat-

ing systems that cannot detect the presence of USB devices. The options are

Disabled and Enabled.

USB Hardware Delays and Time-Out

USB Transfer Time-Out

Use the keyboard to enter the time-out value for USB Control/Bulk/Interrupt

transfers. The options are 1 sec, 5 sec, 10 sec, and 20 sec.

Device Reset Time-Out

Use the keyboard to enter time-out value during a USB mass storage device

reset. The options are 10 sec, 20 sec, 30, and 40 sec.

4-18

A1SAi & A1SRi Series Motherboard User’s Manual

Device Power-up Delay

Use the feature to set the maximum time a USB device will wait before report-

ing itself to the host controller. Select Auto to use the manufacturer's default

setting. Select Manual to set the default setting manually. The options are Auto

and Manual.

SATA Conguration

When this submenu is selected, the AMI BIOS automatically detects the presence

of the SATA Devices and displays the following items:

SATA 3 Controller

This feature allows the user to congure the settings of SATA 3.0 devices

Sata 3 Controller

Select Enabled to enable the onboard SATA 3.0 controller. The options are Enabled

and Disabled.

Sata Mode

This item sets SATA device mode. The options are IDE and AHCI.

Sata 3 Speed

Use this feature to select the highest allowable speed for the SATA 3.0 controller.

The options are Gen 1, Gen 2, and Gen3.

LPM (Link Power Management)

Select Enabled to support Link Power Management to improve system power

management. The options are Enabled and Disabled.

Overwrite SIR Values

Select Enabled to overwrite SIR values. The options are Disabled and Enabled.

If Overwrite SIR Values is set to Enabled, the three items below are available

for conguration:

Hex value of LBC01

Use this feature to select the hex value for LBC01. Use the keypad to enter a

value.

Hex value of LBC23

Use this feature to select the hex value for LBC23. Use the keypad to enter a

value.

Chapter 4: AMI BIOS

4-19

Hex value of LBC45

Use this feature to select the hex value for LBC45. Use the keypad to enter a

value.

SATA Port 0/SATA Port 1

The submenu below allows the user to congure the following settings for SATA

Port 0 or SATA Port 1.

Spin Up

On an edge detect from 0 to 1, use this feature to set a COMRESET initialization

sequence for a device. The options are Enabled and Disabled.

Hot Plug

Set this item to Enabled for hot-plugging support, which will allow the user to re-

place a SATA drive without shutting down the system. The options are Enabled

and Disabled.

External Device

Select Enabled for external SATA device support. The options are Enabled and

Disabled.

Mechanical Switch

Select Enabled for mechanical switch support. The options are Enabled and Dis-

abled.

SATA 2 Controller

This feature allows the user to congure the settings of SATA 2.0 devices

Sata Controller

Select Enabled to enable the onboard SATA 2.0 controller on the motherboard. The

options are Disabled and Enabled.

Sata Mode

This item selects the mode for the installed SATA drives. The options are IDE and

AHCI.

LPM (Link Power Management)

Select Enabled to support Link Power Management to improve system power

management. The options are Disabled and Enabled.

Overwrite SIR Values

Select Enabled to overwrite SIR values. The options are Disabled and Enabled.

4-20

A1SAi & A1SRi Series Motherboard User’s Manual

If Overwrite SIR Values is set to Enabled, the three items below are available

for conguration:

Hex value of LBC01

Use this feature to select the hex value for LBC01. Use the keypad to enter a

value.

Hex value of LBC23

Use this feature to select the hex value for LBC23. Use the keypad to enter a

value.

Hex value of LBC45

Use this feature to select the hex value for LBC45. Use the keypad to enter a

value.

SATA Port 2/SATA Port 3/SATA Port 4/SATA Port 5

(SATA Ports 4/5 are available on all A1SAi/A1SRi models except for A1SRi-

2358F)

The submenu below allows the user to congure the following settings for SATA

Port 2/SATA Port 3/SATA Port4/SATA Port 5.

Spin Up

On an edge detect from 0 to 1, use this feature to set a COMRESET initialization

sequence for a device. The options are Enabled and Disabled.

External Device

Select Enabled for external SATA device support. The options are Enabled and

Disabled.

Hot Plug

Set this item to Enabled for hot-plugging support, which will allow the user to re-

place a SATA drive without shutting down the system. The options are Enabled

and Disabled.

Mechanical Switch

Select Enabled for mechanical switch support. The options are Disabled and

Enabled.

Chapter 4: AMI BIOS

4-21

PCIe/PCI/PnP Conguration

PCI Latency Timer

Use this feature to set the latency Timer of each PCI device installed on a PCI bus.

Select 32 to set the PCI latency to 32 PCI clock cycles. The options are 32 PCI

Bus Clocks, 64 PCI Bus Clocks, 96 PCI Bus Clocks, 128 PCI Bus Clocks, 160 PCI

Bus Clocks, 192 PCI Bus Clocks, 224 PCI Bus Clocks and 248 PCI Bus Clocks.

VGA Palette Snoop

Select Enabled to support VGA palette register snooping which will allow the PCI

cards that do not contain their own VGA color palettes to examine the video cards

palette to mimic it for proper color display. The options are Disabled and Enabled.

PERR# Generation

Select Enabled to allow a PCI device to generate a PERR number for a PCI Bus

Signal Error Event. The options are Disabled and Enabled.

SERR# Generation

Select Enabled to allow a PCI device to generate an SERR number for a PCI Bus

Signal Error Event. The options are Disabled and Enabled.

System Error Logging

If this item is set to enabled, an error log will be created when a system error oc-

curs. The options are Enabled and Disabled.

Maximum Payload

Select Auto to allow the system BIOS to automatically set the maximum payload

value for a PCI-E device to enhance system performance. The options are Auto,

128 Bytes, 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, and 4096 Bytes.

Maximum Read Request

Select Auto to allow the system BIOS to automatically set the maximum Read

Request size for a PCI-E device to enhance system performance. The options are

Auto, 128 Bytes, 256 Bytes, 512 Bytes, 1024 Bytes, 2048 Bytes, and 4096 Bytes.

ASPM Support

This feature allows the user to set the Active State Power Management (ASPM)

level for a PCI-E device. Select Force L0 to force all PCI-E links to operate at L0

state. Select Auto to allow the system BIOS to automatically set the ASPM level for

the system. Select Disabled to disable ASPM support. The options are Disabled

and Auto.

Warning: Enabling ASPM support may cause some PCI-E devices to fail!

4-22

A1SAi & A1SRi Series Motherboard User’s Manual

Above 4G Decoding (Available if the system supports 64-bit PCI decoding)

Select Enabled to decode a 64-bit PCI device in the space above 4G Address. The

options are Disabled and Enabled.

Launch Storage OpROM Policy

This feature controls how the system executes UEFI (Unied Extensible Firmware

Interface), and legacy storage OPROM. Select Legacy to boot the system using a

legacy storage device. The options are Do Not Launch, UEFI, and Legacy.

PCIe Slot 1 Bifurcation

This feature allows the user to congure the following PCIe slot bifurcation control

settings for PCIe slot 1. The options are Auto and X4X4.

PCIe Slot 1 OPROM

Select Enabled to enable Option ROM support to boot the computer using a net-

work interface device install in the slot specied above. The options are Disabled

and Enabled.

Launch Video OpROM Policy

This feature controls how the system executes UEFI (Unied Extensible Firmware

Interface) and video device OPROM. Select Legacy to boot the system using a

legacy device installed in a video port. The options are Do Not Launch, UEFI, and

Legacy.

VGA Priority

This feature allows the user to select the graphics adapter to be used as the primary

boot device. The options are Onboard and Offboard.

Launch Network OpROM Policy

This feature controls how the system executes UEFI (Unied Extensible Firmware

Interface) and LAN device OPROM. Select Legacy to boot the system using a legacy

device installed in a LAN port. The options are Do Not Launch, UEFI, and Legacy.

Onboard LAN Option ROM Select

Select iSCSI to use the iSCSI Option ROM to boot the computer using a network

device. Select PXE (Preboot Execution Environment) to use an PXE Option ROM

to boot the computer using a network device. The options are PXE and iSCSI.

Chapter 4: AMI BIOS

4-23

Load Onboard LAN1 Option ROM/Load Onboard LAN2 Option ROM/Load
Onboard LAN3 Option ROM/Load Onboard LAN4 Option ROM

Select Enabled to enable the onboard LAN1 Option ROM~LAN4 Option ROM.

This is to boot the computer using a network device. The default setting for LAN1

Option ROM is Enabled, and the default settings for LAN2 Option ROM/LAN3

Option ROM/LAN4 Option ROM are Disabled.

ACPI Settings

WHEA Support

This feature Enables the Windows Hardware Error Architecture (WHEA) support for

the Windows 2008 (or a later version) operating system. The options are Disabled

and Enabled.

PCI AER Support

Select Enabled to enable the ACPI OS to manage PCI Advanced Error Reporting.

The options are Disabled and Enabled.

Trusted Computing Conguration (Available when a TPM

Device is Detected and TPM Jumper is Enabled)

Conguration

Security Device Support

Select Enable for the AMI BIOS to automatically download the drivers needed

to provide Trusted Computing platform support for this machine to ensure date

integrity and network security. The options are Disabled and Enabled.

TPM State

Select Enabled to use TPM (Trusted Platform Module) settings for system data

security. The options are Disabled and Enabled.

Note: The system will reboot for the change on TPM State to take effect.

Pending Operation

Use this item to schedule a TPM-related operation to be performed by a security

device for TPM support. The options are None and TPM Clear.

Note: The computer will reboot to carry out a pending TPM operation and

change TPM state for a TPM device.

Current Status Information

This feature indicates the status of the following TPM items:

4-24

A1SAi & A1SRi Series Motherboard User’s Manual

TPM Enabled Status

TPM Active Status

TPM Owner Status

Super IO Conguration

Super IO Chip AST2400

Serial Port 0 Conguration/Serial Port 1 Conguration

This submenu allows the user the congure settings of Serial Port 1 or Serial Port 2.

Serial Port

Select Enabled to enable the a selected onboard serial port. The options are Dis-

abled and Enabled.

Device Settings

This item displays the status of a serial part specied by the user.

Change Settings

This feature species the base I/O port address and the Interrupt Request address

of a serial port specied by the user. Select Auto to allow the BIOS to automatically

assign the base I/O and IRQ address.

The options for Serial Port 1 are Auto, (IO=3F8h; IRQ=4), (IO=3F8h; IRQ=3, 4, 5,

6, 7, 9, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12), (IO=3E8h; IRQ=3,

4, 5, 6, 7, 9, 10, 11, 12) and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12).

The options for Serial Port 2 are Auto, (IO=2F8h; IRQ=3), (IO=3F8h; IRQ=3, 4, 5,

6, 7, 9, 10, 11, 12), (IO=2F8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12), (IO=3E8h; IRQ=3,

4, 5, 6, 7, 9, 10, 11, 12) and (IO=2E8h; IRQ=3, 4, 5, 6, 7, 9, 10, 11, 12).

Device Mode

Use this feature to set the optimal setting for a super I/O device. The options are

24MHz/13 and 24MHz.

Serial Port 2 Attribute (Available for Serial Port 2 only)

This feature species the attribute of Serial Port 2. The options are SOL and COM.

Chapter 4: AMI BIOS

4-25

Serial Port Console Redirection

COM1 Console Redirection, COM2/SOL Console Redirection

Console Redirection

Select Enabled to enable console redirection support for a serial port specied by

the user. The options are Enabled and Disabled. By default, console redirection is

Disabled for COM1 and Enabled for COM2

Console Redirection Settings

This feature allows the user to specify how the host computer will exchange data

with the client computer, which is the remote computer used by the user.

Terminal Type

This feature allows the user to select the target terminal emulation type for Con-

sole Redirection. Select VT100 to use the ASCII Character set. Select VT100+ to

add color and function key support. Select ANSI to use the Extended ASCII Char-

acter Set. Select VT-UTF8 to use UTF8 encoding to map Unicode characters

into one or more bytes. The options are ANSI, VT100, VT100+, and VT-UTF8.

Bits Per second

Use this feature to set the transmission speed for a serial port used in Console

Redirection. Make sure that the same speed is used in the host computer and the

client computer. A lower transmission speed may be required for long and busy

lines. The options are 9600, 19200, 38400, 57600 and 115200 (bits per second).

Data Bits

Use this feature to set the data transmission size for Console Redirection. The

options are 7 Bits and 8 Bits.

Parity

A parity bit can be sent along with regular data bits to detect data transmission

errors. Select Even if the parity bit is set to 0, and the number of 1's in data bits

is even. Select Odd if the parity bit is set to 0, and the number of 1's in data bits

is odd. Select None if you do not want to send a parity bit with your data bits

in transmission. Select Mark to add a mark as a parity bit to be sent along with

the data bits. Select Space to add a Space as a parity bit to be sent with your

data bits. The options are None, Even, Odd, Mark, and Space.

4-26

A1SAi & A1SRi Series Motherboard User’s Manual

Stop Bits

A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard

serial data communication. Select 2 Stop Bits if slower devices are used. The

options are 1 and 2.

Flow Control

Use this feature to set the ow control for Console Redirection to prevent data

loss caused by buffer overow. Send a "Stop" signal to stop sending data when

the receiving buffer is full. Send a "Start" signal to start sending data when the

receiving buffer is empty. The options are None and Hardware RTS/CTS.

VT-UTF8 Combo Key Support

Select Enabled to enable VT-UTF8 Combination Key support for ANSI/VT100

terminals. The options are Enabled and Disabled.

Recorder Mode

Select Enabled to capture the data displayed on a terminal and send it as text

messages to a remote server. The options are Disabled and Enabled.

Resolution 100x31

Select Enabled for extended-terminal resolution support. The options are Dis-

abled and Enabled.

Legacy OS Redirection Resolution

Use this feature to select the number of rows and columns used in Console

Redirection for legacy OS support. The options are 80x24 and 80x25.

Putty KeyPad

This feature selects the settings for Function Keys and KeyPad used for Putty,

which is a terminal emulator designed for the Windows OS. The options are

VT100, LINUX, XTERMR6, SC0, ESCN, and VT400.

Redirection After BIOS POST

Use this feature to enable or disable legacy console redirection after BIOS POST.

When set to Bootloader, legacy console redirection is disabled before booting

the OS. When set to Always Enable, legacy console redirection remains enabled

when booting the OS. The options are Always Enable and Bootloader.

Serial Port for Out-of-Band Management/Windows Emergency Management

Services (EMS)

The submenu allows the user to congure Console Redirection settings to support

Out-of-Band Serial Port management.

Chapter 4: AMI BIOS

4-27

Console Redirection (for EMS)

Select Enabled to use a COM Port selected by the user for Console Redirection.

The options are Enabled and Disabled.

Console Redirection Settings (for EMS)

This feature allows the user to specify how the host computer will exchange

data with the client computer, which is the remote computer used by the user.

Out-of-Band Mgmt Port

The feature selects a serial port used by the Microsoft Windows Emergency

Management Services (EMS) to communicate with a remote server. The options

are COM1 Console Redirection and COM2/SOL Console Redirection.

Terminal Type

This feature allows the user to select the target terminal emulation type for Con-

sole Redirection. Select VT100 to use the ASCII character set. Select VT100+

to add color and function key support. Select ANSI to use the extended ASCII

character set. Select VT-UTF8 to use UTF8 encoding to map Unicode characters

into one or more bytes. The options are ANSI, VT100, VT100+, and VT-UTF8.

Bits Per Second

This item sets the transmission speed for a serial port used in Console Redirec-

tion. Make sure that the same speed is used in the host computer and the client

computer. A lower transmission speed may be required for long and busy lines.

The options are 9600, 19200, 57600, and 115200 (bits per second).

Flow Control

This feature allows the user to set the ow control for Console Redirection to

prevent data loss caused by buffer overow. Send a "Stop" signal to stop send-

ing data when the receiving buffer is full. Send a "Start" signal to start sending

data when the receiving buffer is empty. The options are None, Hardware RTS/

CTS, and Software Xon/Xoff.

Data Bits, Parity, Stop Bits

The status of each item above is displayed.

4-28

A1SAi & A1SRi Series Motherboard User’s Manual

iSCSi Conguration

iSCSI Initiator Name

This feature allows the user to enter the unique name of the iSCSI Initiator in IQN

format. Once the name of the iSCSI Initiator is entered into the system, congure

the proper settings for the following items.

Add an Attempt

Delete Attempts

Change Attempt order

Chapter 4: AMI BIOS

4-29

4-4 IPMI

Use this feature to congure Intelligent Platform Management Interface (IPMI)

settings.

IPMI Firmware Revision

This item indicates the IPMI rmware revision used in your system.

Status BMC (Baseboard Management Controller)

This item indicates the status of the IPMI rmware installed in your system.

BMC Network Conguration

BMC Network Congifuration

Lan channel 1: This feature allows the user to congure the setting for IPMI Port 1.

Conguration Address Source

This feature allows the user to select the source of the IP address for this com-

puter. If Static is selected, you will need to know the IP address of this computer

and enter it to the system manually in the eld. If DHCP is selected, the BIOS will

search for a DHCP (Dynamic Host Conguration Protocol) server in the network

that is attached to and request the next available IP address for this computer.

The options are DHCP and Static. The following items are assigned IP addresses

automatically if DHCP is selected.

4-30

A1SAi & A1SRi Series Motherboard User’s Manual

Station IP Address

This item displays the Station IP address for this computer. This should be in decimal

and in dotted quad form (i.e., 192.168.10.253).

Subnet Mask

This item displays the sub-network that this computer belongs to. The value of each

three-digit number separated by dots should not exceed 255.

Station MAC Address

This item displays the Station MAC address for this computer. Mac addresses are

6 two-digit hexadecimal numbers.

Router IP Address

This item displays the Router IP address for this computer. This should be in decimal

and in dotted quad form (i.e., 192.168.10.253).

Router MAC Address

This item displays the Router MAC address for this computer. Mac addresses are

6 two-digit hexadecimal numbers.

Chapter 4: AMI BIOS

4-31

4-5 Event Logs

Use this feature to congure Event Log settings.

Change Smbios Event Log Settings

Enabling/Disabling Options

Smbios Event Log

Change this item to enable or disable all features of the SMBIOS Event Logging

during system boot. The options are Disabled and Enabled.

Erasing Settings

Erase Event Log

If No is selected, data stored in the event log will not be erased. Select Yes, Next

Reset, data in the event log will be erased upon next system reboot. Select Yes,

Every Reset, data in the event log will be erased upon every system reboot. The

options are No, Yes, Next reset, and Yes, Every reset.

When Log is Full

Select Erase Immediately for all messages to be automatically erased from the

event log when the event log memory is full. The options are Do Nothing and

Erase Immediately.

4-32

A1SAi & A1SRi Series Motherboard User’s Manual

Smbios Event Long Standard Settings

Log System Boot Event

This option toggles the System Boot Event logging to enabled or disabled. The

options are Disabled and Enabled.

MECI

The Multiple Event Count Increment (MECI) counter counts the number of occurenc-

es that a duplicate event must happen before the MECI counter is incremented.

This is a numeric value. The default value is 1.

METW

The Multiple Event Time Window (METW) denes number of minutes must pass

between duplicate log events before MECI is incremented. This is in minutes, from

0 to 99. The default value is 60.

Custom Options

Log OEM Codes

Select Enabled to log the status of OEM EFI codes. The options are Enabled and

Disabled.

Convert OEM Codes

Select Enabled to convert the OEM Status codes to the standard SMBIOS codes.

The options are Enabled and Disabled.

View SMBIOS Event Log

This section displays the contents of the SMBIOS Event Log.

Chapter 4: AMI BIOS

4-33

4-6 Boot

Use this feature to congure Boot Settings:

Boot Option Priorities

This option prioritizes the order of bootable devices that the system to boot from.

Press [ENTER] on each entry from top to bottom to select devices.

• Boot Option #1

• Boot Option #2

Network Device BBS Priorities

This feature allows the user to specify which UEFI network drive devices are boot

devices.

• Boot Option #1

Delete Boot Option

Use this feature to remove a pre-dened boot device from which the system will

boot during startup.

The settings are [any pre-dened boot device].



Delete Driver Option

This feature allows the user to delete a previously dened boot device from which

the systems boots during startup.

The settings are [any pre dened boot device]

4-34

A1SAi & A1SRi Series Motherboard User’s Manual

4-7 Security

This menu allows the user to congure the following security settings for the

system.

• If the Administrator password is dened ONLY - this controls access to the

BIOS setup ONLY.

• If the User's password is dened ONLY - this password will need to be entered

upon each system boot, and will also have Administrator rights in the setup.

• Passwords must be at least 3 and up to 20 characters long.

Administrator Password

Press Enter to create a new, or change an existing Administrator password.

User Password

Use this feature to set a User Password which is required to log into the system

and to enter the BIOS setup utility. The length of the password should be from 3

characters to 20 characters long.

Secure Boot Menu

This section displays the contents of the following secure boot features:

• System Mode

• Secure Boot

Chapter 4: AMI BIOS

4-35

Secure Boot Mode

Use this item to select the secure boot mode. The options are Standard and

Custom.

Key Management

This submenu allows the user to congure the following Key Management settings.

Default Key Provision

Select Enabled to install the default Secure Boot keys set by the manufacturer. The

options are Disabled and Enabled.

Enroll All Factory Default Keys

Select Yes to install all default secure keys set by the manufacturer. The options

are Yes and No.

Save All Secure Boot Variables

This feature allows the user to decide if all secure boot variables should be saved.

Platform Key (PK)

This feature allows the user to congure the settings of the platform keys.

Delete PK

This feature allows the user to congure the settings for platform keys deletion.

Set New PK

Select Yes to load the new platform keys from the manufacturer's defaults. Select

No to load the platform keys from a le. The options are Yes and No.

Key Exchange Key (KEK)

Set new KEK

Select Yes to load the KEK from the manufacturer's defaults. Select No to load the

KEK from a le. The options are Yes and No.

Append KEK

Select Yes to add the KEK from the manufacturer's defaults list to the existing KEK.

Select No to load the KEK from a le. The options are Yes and No.

4-36

A1SAi & A1SRi Series Motherboard User’s Manual

Authorized Signatures (DB)

Set new DB

Select Yes to load the database from the manufacturer's defaults. Select No to load

the DB from a le. The options are Yes and No.

Append DB

Select Yes to add the database from the manufacturer's defaults to the existing DB.

Select No to load the DB from a le. The options are Yes and No.

Authorized TimeStamps

Set new DBT

Select Yes to load the DBT from the manufacturer's defaults. Select No to load the

DBT from a le. The options are Yes and No.

Append DBT

Select Yes to add the DBT from the manufacturer's defaults list to the existing DBT.

Select No to load the DBT from a le. The options are Yes and No.

Forbiden Signatures (DBX)

Set new DBX

Select Yes to load the DBX from the manufacturer's defaults. Select No to load the

DBX from a le. The options are Yes and No.

Append DBX

Select Yes to add the DBX from the manufacturer's defaults to the existing DBX.

Select No to load the DBX from a le. The options are Yes and No.

Chapter 4: AMI BIOS

4-37

4-8 Save & Exit

Select the Exit tab from the BIOS setup utility screen to enter the Exit BIOS Setup

screen.

Discard Changes and Exit

Select this option to quit the BIOS Setup without making any permanent changes

to the system conguration, and reboot the computer. Select Discard Changes and

Exit from the Exit menu and press <Enter>.

Save Changes and Reset

When you have completed the system conguration changes, select this option to

leave the BIOS setup utility and reboot the computer, so the new system congura-

tion parameters can take effect. Select Save Changes and Exit from the Exit menu

and press <Enter>.

Save Options

Save Changes

After completing the system conguration changes, select this option to save the

changes you have made. This will not reset (reboot) the system.

Discard Changes

Select this option and press <Enter> to discard all the changes and return to the

AMI BIOS utility Program.

4-38

A1SAi & A1SRi Series Motherboard User’s Manual

Restore Defaults

To set this feature, select Restore Defaults from the Save & Exit menu and press

<Enter>. These are factory settings designed for maximum system stability, but not

for maximum performance.

Save As User Defaults

To set this feature, select Save as User Defaults from the Exit menu and press <En-

ter>. This enables the user to save any changes to the BIOS setup for future use.

Restore User Defaults

To set this feature, select Restore User Defaults from the Exit menu and press <En-

ter>. Use this feature to retrieve user-dened settings that were saved previously.

Boot Override

Listed on this section are other boot options for the system (i.e., Built-in EFI shell).

Select an option and press <Enter>. Your system will boot to the selected boot

option.

Appendix A: POST Error Beep Codes

A-1

Appendix A

BIOS Error Beep Codes

During the POST (Power-On Self-Test) routines, which are performed each time

the system is powered on, errors may occur.

Non-fatal errors are those which, in most cases, allow the system to continue

with bootup. The error messages normally appear on the screen.

Fatal errors will not allow the system to continue to bootup. If a fatal error oc-

curs, you should consult with your system manufacturer for possible repairs.

These fatal errors are usually communicated through a series of audible beeps.

The numbers on the fatal error list correspond to the number of beeps for the

corresponding error.

A-1 BIOS Error Beep Codes

BIOS Error Beep Codes

Beep Code/LED Error Message Description

1 beep Refresh Circuits have been reset.

(Ready to power up)

5 short beeps + 1 long
beep

Memory error No memory detected in the

system

8 beeps Display memory

read/write error

Video adapter missing or with
faulty memory

OH LED On System OH System Overheat

A-2

A1SAi & A1SRi Series Motherboard User’s Manual

Notes

Appendix B: Software Installation Instructions

B-1

Appendix B

Software Installation Instructions

B-1 Installing Software Programs

The Supermicro ftp site contains drivers and utilities for your system at ftp://ftp.

supermicro.com. Some of these must be installed, such as the chipset driver.

After accessing the ftp site, go into the CDR_Images directory and locate the ISO

le for your motherboard. Download this le to create a CD/DVD of the drivers and

utilities it contains. (You may also use a utility to extract the ISO le if preferred.)

Another option is to go to the Supermicro Website at http://www.supermicro.com/

products/. Find the product page for your motherboard here, where you may down-

load individual drivers and utilities.

After creating a CD/DVD with the ISO les, insert the disk into the CD/DVD drive

on your system and the display shown below should appear.

Note 1: Click the icons showing a hand writing on paper to view the

readme les for each item. Click the computer icons to the right of these

items to install each item (from top to the bottom) one at a time. After

installing each item, you must re-boot the system before moving on

to the next item on the list. The bottom icon with a CD on it allows you

to view the entire contents.

Note 2: When making a storage driver diskette by booting into a Driver

CD, please set the SATA Conguration to "Compatible Mode" and congure

SATA as IDE in the BIOS Setup. After making the driver diskette, be sure

to change the SATA settings back to your original settings.

Driver/Tool Installation Display Screen

B-2

A1SAi & A1SRi Series Motherboard User’s Manual

B-2 Installing SuperDoctor5

The Supermicro SuperDoctor® 5 is a hardware monitoring program that functions in

a command-line or web-based interface in Windows and Linux operating systems.

The program monitors system health information such as CPU temperature, system

voltages, system power consumption, fan speed, and provides alerts via email or

Simple Network Management Protocol (SNMP).

SuperDoctor 5 comes in local and remote management versions and can be used

with Nagios to maximize your system monitoring needs. With SuperDoctor 5 Man-

agement Server (SSM Server), you can remotely control power on/off and reset

chassis intrusion for multiple systems with SuperDoctor 5 or IPMI. SD5 Manage-

ment Server monitors HTTP, FTP, and SMTP services to optimize the efciency of

your operation.

Note: The default User Name and Password for SuperDoctor 5 is admin

/admin.

SuperDoctor 5 Interface Display Screen (Health Information)

Note: The SuperDoctor 5 program and User’s Manual can be downloaded

from the Supermicro web site at http://www.supermicro.com/products/nfo/

sms_sd5.cfm.