Supero 6026TT-BIBXF, 6026TT-BIBQRF, 6026TT-BIBXRF, 6026TT-BIBQF, 6026TT-BTRF User Manual
...
®
SUPER
SUPERSERVER 6026TT-BT(R)F
SUPERSERVER 6026TT-BIBX(R)F
S
UPERSERVER 6026TT-BIBQ(R)F
USER’S MANUAL
Revision 1.0a
The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this
manual, please see our web site at www.supermicro.com.
Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software, if any,
and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or
reduced to any medium or machine without prior written consent.
IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT , SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTW ARE, OR DA TA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.
Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for
all claims will not exceed the price paid for the hardware product.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.
California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”
WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.
Manual Revision 1.0a
Release Date: December 2, 2009
Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.
Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.
Copyright © 2009 by Super Micro Computer, Inc.
All rights reserved.
Printed in the United States of America
Preface
About This Manual
This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the SuperServer 6026TT-BT(R)
F/BIBX(R)F/BIBQ(R)F. Installation and maintenance should be performed by experienced technicians only.
Preface
The SuperServer SuperServer 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F is a 2U Twin
(four serverboards/nodes in a 2U chassis) rackmount server based on the SC827B(R)1400B server chassis and four Super X8DTT-F/X8DTT-IBXF/X8DTT-IBQF
serverboards. An optional redundant power supply may be added to the system
(indicated by the "(R)" in the product name).
Manual Organization
Chapter 1: Introduction
The fi rst chapter provides a checklist of the main components included with the
server system and describes the main features of the Super X8DTT-F/X8DTT-IBXF/
X8DTT-IBQF serverboard and the SC827B-(R)1400B chassis.
Chapter 2: Server Installation
This chapter describes the steps necessary to install the SuperServer 6026TT-BT(R)
F/BIBX(R)F/BIBQ(R)F into a rack and check out the server confi guration prior to
powering up the system. If your server was ordered without the processor and
memory components, this chapter will refer you to the appropriate sections of the
manual for their installation.
2
Chapter 3: System Interface
Refer to this chapter for details on the system interface, which includes the functions
and information provided by the control panel on the chassis as well as other LEDs
located throughout the system.
iii
SUPERSERVER 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F User's Manual
Chapter 4: System Safety
You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F.
Chapter 5: Advanced Serverboard Setup
Chapter 5 provides detailed information on the X8DTT-F/X8DTT-IBXF/X8DTT-IBQF
serverboard, including the locations and functions of connectors, headers and jumpers. Refer to this chapter when adding or removing processors or main memory
and when reconfi guring the serverboard.
Chapter 6: Advanced Chassis Setup
Refer to Chapter 6 for detailed information on the SC827B-(R)1400B 2U rackmount
server chassis. You should follow the procedures given in this chapter when installing, removing or reconfi guring SAT A or peripheral drives and when replacing system
power supply units and cooling fans.
Chapter 7: BIOS
The BIOS chapter includes an introduction to BIOS and provides detailed information on running the CMOS Setup Utility.
Appendix A: BIOS Error Beep Codes
Appendix B: Installing Windows
Appendix C: System Specifi cations
iv
Notes
Preface
v
SUPERSERVER 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F User's Manual
Table of Contents
Chapter 1 Introduction
1-1 Overview .........................................................................................................1-1
1-2 Serverboard Features .....................................................................................1-2
Processors ......................................................................................................1-2
Memory ...........................................................................................................1-2
Serial ATA ........................................................................................................ 1-2
PCI Expansion Slots ....................................................................................... 1-2
Ethernet Ports ................................................................................................. 1-2
Onboard Controllers/Ports .............................................................................. 1-3
Graphics Controller ......................................................................................... 1-3
Other Features ................................................................................................1-3
Infi niBand ........................................................................................................ 1-3
1-3 Server Chassis Features ................................................................................ 1-5
System Power .................................................................................................1-5
SATA Subsystem .............................................................................................1-5
Control Panel ..................................................................................................1-5
Rear I/O Panel ................................................................................................ 1-5
Cooling System ...............................................................................................1-5
1-4 2U Twin
Nodes ..............................................................................................................1-6
System Power .................................................................................................1-6
SATA Backplane/Drives ...................................................................................1-6
1-5 Contacting Supermicro .................................................................................... 1-7
2
: System Notes .................................................................................1-6
Chapter 2 Server Installation
2-1 Overview .........................................................................................................2-1
2-2 Unpacking the System ....................................................................................2-1
2-3 Preparing for Setup ......................................................................................... 2-1
Choosing a Setup Location ............................................................................. 2-2
Rack Precautions ............................................................................................2-2
Server Precautions .......................................................................................... 2-2
Rack Mounting Considerations .......................................................................2-3
Ambient Operating Temperature ................................................................2-3
Reduced Airfl ow ......................................................................................... 2-3
Mechanical Loading ...................................................................................2-3
Circuit Overloading ..................................................................................... 2-3
Reliable Ground .........................................................................................2-3
vi
Table of Contents
Removing the Protective Film ......................................................................... 2-4
2-4 Rack Mounting Instructions ............................................................................. 2-5
Separating the Sections of the Rack Rails ..................................................... 2-5
Installing the Inner Rail Extensions ................................................................ 2-6
Outer Rack Rails ............................................................................................. 2-7
2-5 Checking the Serverboard Setup ....................................................................2-9
2-6 Preparing to Power On ................................................................................. 2-10
Chapter 3 System Interface
3-1 Overview .........................................................................................................3-1
3-2 Control Panel Buttons .....................................................................................3-1
Power ..............................................................................................................3-1
UID ..................................................................................................................3-1
3-3 Control Panel LEDs ........................................................................................3-2
Overheat/Fan Fail ...........................................................................................3-2
NIC ..................................................................................................................3-2
3-4 SATA Drive Carrier LEDs ................................................................................ 3-2
Chapter 4 System Safety
4-1 Electrical Safety Precautions .......................................................................... 4-1
4-2 General Safety Precautions ............................................................................4-2
4-3 ESD Precautions .............................................................................................4-3
4-4 Operating Precautions .................................................................................... 4-4
Chapter 5 Advanced Serverboard Setup
5-1 Handling the Serverboard ...............................................................................5-1
Precautions .....................................................................................................5-1
5-2 I/O Ports .......................................................................................................... 5-2
Unpacking .......................................................................................................5-2
5-3 Processor and Heatsink Installation................................................................5-3
Installing LGA1366 Processors .......................................................................5-3
Installing a CPU Heatsink ...............................................................................5-5
Removing the Heatsink ................................................................................... 5-6
5-4 Installing Memory ............................................................................................ 5-7
5-5 Adding PCI Cards ........................................................................................... 5-9
5-6 Serverboard Details ...................................................................................... 5-10
X8DTT-F/ X8DT T-IBXF/X8DTT-IBQF Quick Reference .................................5-11
5-7 Connector Defi nitions .................................................................................... 5-12
5-8 Jumper Settings ............................................................................................5-16
5-9 Onboard Indicators ........................................................................................ 5-18
5-10 Installing Additional Drivers ...........................................................................5-19
vii
SUPERSERVER 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F User's Manual
5-11 Confi guring Supero Doctor III ....................................................................... 5-20
Chapter 6 Advanced Chassis Setup
6-1 Static-Sensitive Devices .................................................................................. 6-1
Precautions .....................................................................................................6-1
Unpacking .......................................................................................................6-1
6-2 Control Panel ..................................................................................................6-2
6-3 System Fans ...................................................................................................6-2
Fan Confi guration ............................................................................................6-3
System Fan Failure ......................................................................................... 6-3
6-4 Hard Drive Installation/Removal......................................................................6-4
Overview .........................................................................................................6-4
Installing and Removing Hard Drives .............................................................6-4
6-5 Node Installation/Removal ..............................................................................6-7
6-6 Installing the Air Shrouds ................................................................................ 6-8
Air Shrouds .....................................................................................................6-8
6-7 Power Supply .................................................................................................. 6-9
Power Supply Failure: Single Power Supply Module ..................................... 6-9
Power Supply Failure: Redundant Power (Two Modules) ............................6-10
Chapter 7 BIOS
7-1 Introduction ...................................................................................................... 7-1
Starting BIOS Setup Utility .............................................................................. 7-1
How To Change the Confi guration Data .........................................................7-1
Starting the Setup Utility ................................................................................. 7-2
7-2 Main Setup ......................................................................................................7-2
7-3 Advanced Setup Confi gurations...................................................................... 7-4
7-4 Security Settings ...........................................................................................7-24
7-5 Boot Confi guration ........................................................................................ 7-25
7-6 Exit Options ...................................................................................................7-26
Appendix A BIOS Error Beep Codes
Appendix B Installing Windows
Appendix C System Specifi cations
viii
Chapter 1: Introduction
Chapter 1
Introduction
1-1 Overview
The SuperServer 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F is a "2U Twin2" server
comprised of the SC827B-(R)1400B 2U chassis and four X8DTT-F/X8DTT-IBXF/
X8DTT-IBQF serverboards. Please refer to our web site for information on operating
systems that have been certifi ed for use with the 6026TT (www.supermicro.com).
In addition to the serverboard and chassis, various hardware components may have
been included with the system, as listed below.
Eight passive CPU heatsinks (SNK-P0037P)
•
Four 8-cm cooling fans (FAN-0111L4)•
Four air shrouds (MCP-310-82706-0B)•
SATA Accessories: •
Twelve SATA hard drive carriers (three per node) (MCP-220-00024-0B)
One internal HDD backplane (BPN-SAS-827B)
Four SATA cable sets (CBL-0317L)
Four PCI Express x16 riser cards (RSC-R1U-E16R)
•
Rackmount rails kit (MCP-290-00053-0N)•
One CD containing drivers and utilities•
SuperServer 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F User's Manual•
1-1
SUPERSERVER 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F User's Manual
1-2 Serverboard Features
At the heart of the SuperServer 6026TT are four X8DTT-F/X8DTT-IBXF/X8DTTIBQF dual processor serverboards, which are based on Intel's 5520 (North Bridge)
+ ICH10R (South Bridge) chipset. (For OEM only, the Intel 5500 is also available
for the North Bridge portion of the chipset.) Below are the main features of the
serverboards. Note that the features on each board are quadrupled for the server,
which includes four nodes.
Processors
Each X8DTT-F/X8DTT-IBXF/X8DTT-IBQF supports two Intel® 5500 Series processors in LGA1366 sockets. Please refer to our web site for a complete listing of
supported processors (www.supermicro.com).
Memory
Each X8DTT-F/X8DTT-IBXF/X8DTT-IBQF has twelve 240-pin DIMM sockets that
can support up to 96 GB of registered ECC DDR3-1333/1066/800 SDRAM (384
GB for the system). Alternatively, up to 24 GB of unbuffered DIMMs per node may
be used. See Chapter 5 Section 6 for more details on installing memory into the
system.
Serial ATA
The Sout h Br idg e (ICH10R) of the c hips et inc lude s a Ser ial ATA cont rol ler fo r six
Gb/s SATA drives . The hot-swappable SATA drives are connected to a backplane
that provides power, bus termination and confi guration settings. RA ID 0, 1, 10 and
5 are suppo r ted. Refe r to the su ppo r t area o f our web si te for p roc edur es on s etting up RAID on your system.
PCI Expansion Slots
Each X8DTT-F/X8DTT-IBXF/X8DTT-IBQF board has one PCI Express 2.0 x16 slot,
so four PCI Express 2.0 x16 slots (for low-profi le expansion cards) are provided
in the server. In the 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F server confi guration, riser
cards have been pre-installed to support low-profi le add-on cards.
Ethernet Ports
An Intel® network controller is integrated into each of the serverboards to support
two Gigabit LAN ports (100/1000Base-T/1000BaseTX, RJ45 output).
1-2
Chapter 1: Introduction
Onboard Controllers/Ports
Onboard I/O backpanel ports on each serverboard include one COM port, a VGA
port, two USB ports, a dedicated IPMI LAN port and two Gigabit LAN (NIC) ports.
An Infi niBand port is also included on the X8DTT-IBXF/X8DTT-IBQF serverboards
(the 6026TT-BIBX(R)F and 6026TT-BIBQ(R)F only). There are four sets of I/O ports
included in the server (one set for each serverboard).
Graphics Controller
The X8DTT-F/X8DTT-IBXF/X8DTT-IBQF features an integrated Matrox G200eW
graphics chip.
Other Features
Other onboard features that promote system health include voltage monitors, autoswitching voltage regulators, chassis and CPU overheat sensors, virus protection
and BIOS rescue.
Infi niBand
Both th e 6026T T-B IBX(R)F and 60 26TT-BI BQ(R)F incl ude an Infi niBand port at
DDR (dual dat a rate) and QDR (quad data rate) speed s, respect ively. Infi niBand
is a scalable serial communications link intended for connecting processors with
high-speed peripherals. (Infi niBand requires a QSFP connector.)
1-3
SUPERSERVER 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F User's Manual
QSFP
#1
#1
#1
DDR3 DIMM
#2
#2
#2
AA
BB
CC
DDR3 DIMM
MT25408
Connect-X IB
PCI-E Gen2/DDR or QDR
PCI-E x16
DDR II
CPU#1
PE
PE
WBD
BMC/VGA
Port1 Port0
Ports
3,4
Ports
Intel
Ports
5,6
Ports
7,8,9,10
5
4-1
5520
ESI
DMI
ICH10R
PCI
CPU#2
CLINK
CLINK
LPC
2,1
#2
F
Kawela
RJ45 RJ45
SST25
VF016
SPI
SATA
SATA #1
SATA #2
SATA #3
SATA #4
SATA #5
SATA #6
LPCIO W83527
ACPI
KBC
#2
#2
DDR3 DIMM
DD
EE
F
#1
#1
#1
DDR3 DIMM
VGA
RTL8201N PHY
Dedicate LAN
Figure 1-1. Intel 5520 Chipset:
System Block Diagram
Note: This is a general block diagram. Please see Chapter 5 for details.
1-4
Chapter 1: Introduction
1-3 Server Chassis Features
The following is a general outline of the main features of the SC827B-(R)1400B 2U
chassis. Details on the chassis can be found in Chapter 6.
System Power
When confi gured as a SuperServer 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F, the
SC827B-(R)1400B includes a single 1400W power supply, which provides power
to all four serverboards (nodes). An additional 1400W power supply module (not
included) may be installed to provide redundant power.
SATA Subsystem
The SC827B-(R)1400B chassis was designed to support twelve SATA hard drives,
which a re hot- swappa ble unit s.
Control Panel
The SC827B-(R)1400B features four independant control panels associated with
each serverboard (node) in the chassis. Each control panel has LEDs to indicate
power on, network activity , power fail, fan fail and system overheat conditions. Each
control panel also includes a main power button and a UID button.
Rear I/O Panel
The SC827B-(R)1400B is a 2U rackmount chassis. Its I/O panel provides a slots for
four low-profi le PCI Express x16 expansion cards, four COM ports, eight USB ports,
four VGA ports and eight Gb Ethernet ports. See Chapter 6 for details.
Cooling System
The SC827B-(R)1400B chassis has an innovative cooling design that features four
8-cm high-performance fans. A fan speed control setting in BIOS allows fan speed
to be determined by system temperature. See Chapter 6 for details.
1-5
SUPERSERVER 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F User's Manual
1-4 2U Twin2: System Notes
As a 2U Twin2 confi guration, the 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F is a unique
server system. With four system boards incorporated into a single chassis acting as
four separate nodes, there are several points you should keep in mind.
Nodes
Each of the four serverboards act as a separate node in the system. As independant
nodes, each may be powered off and on without affecting the others. In addition,
each node is a hot-swappable unit that may be removed from the rear of the chassis.
The nodes are connected to the server backplane by means of an adapter card.
System Power
6026TT-BTF/BIBXF/BIBQF: a single 1400W power supply is used to provide the
power for all four serverboards. Each serverboard however, can be shut down
independently of the other with the power button on its own control panel.
6026TT-BTRF/BIBXRF/BIBQRF: this version of the server has an additional
1400W power supply module (two total) for power redundancy. If a power supply
module fails the other backup module will keep the system running until it can be
replaced.
SATA Backplane/Drives
As a system, the 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F supports the use of twelve
SATA drives. A single SATA backplane works to apply system-based control for
power and fan speed functions, yet at the same time logically connects a set of
three SATA drives to each serverboard. Consequently, RAID setup is limited to
a three-drive scheme (RAID cannot be spread across all twelve drives). See the
Drive Bay Installation/Removal section in Chapter 6 for the logical hard drive and
node confi guration.
1-6
Chapter 1: Introduction
1-5 Contacting Supermicro
Headquarters
Address: Super Micro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: +1 (408) 503-8000
Fax: +1 (408) 503-8008
Email: marketing@supermicro.com (General Information)
support@supermicro.com (Technical Support)
Web Site: www.supermicro.com
Europe
Address: Super Micro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: +31 (0) 73-6400390
Fax: +31 (0) 73-6416525
Email: sales@supermicro.nl (General Information)
support@supermicro.nl (Technical Support)
rma@supermicro.nl (Customer Support)
Asia-Pacifi c
Address: Super Micro Computer, Inc.
4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei County
Taiwan, R.O.C.
Tel: +886-(2) 8226-3990
Fax: +886-(2) 8226-3991
Web Site: www.supermicro.com.tw
Technical Support:
Email: support@supermicro.com.tw
Tel: 886-2-8228-1366, ext.132 or 139
1-7
SUPERSERVER 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F User's Manual
Notes
1-8
Chapter 2: Server Installation
Chapter 2
Server Installation
2-1 Overview
This chapter provides a quick setup checklist to get the 6026TT-BT(R)F/BIBX(R)F/
BIBQ(R)F up and running. Following these steps in the order given should enable
you to have the system operational within a minimum amount of time. This quick
setup assumes that your system has come to you with the processors and memory
preinstalled. If your system is not already fully integrated with a serverboard, processors, system memory etc., please turn to the chapter or section noted in each
step for details on installing specifi c components.
2-2 Unpacking the System
You should inspect the box the system was shipped in and note if it was damaged
in any way. If the server itself shows damage you should fi le a damage claim with
the carrier who delivered it.
Decide on a suitable location for the rack unit that will hold the server. It should be
situated in a clean, dust-free area that is well ventilated. Avoid areas where heat,
electrical noise and electromagnetic fi elds are generated. Y ou will also need it placed
near a grounded power outlet. Be sure to read the Rack and Server Precautions
in the next section.
2-3 Preparing for Setup
The box the server was shipped in should include the rackmount hardware needed
to install the system into the rack. Follow the steps in the order given to complete
the installation process in a minimum amount of time. Please read this section in
its entirety before you begin the installation procedure outlined in the sections that
follow.
2-1
SUPERSERVER 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F User's Manual
!
!
Choosing a Setup Location
Leave enough clearance in front of the rack to enable you to open the front •
door completely (~25 inches).
•
Leave approximately 30 inches of clearance in the back of the rack to allow for
suffi cient airfl ow and ease in servicing.
This product is for installation only in a Restricted Access Location (dedicated
•
equipment rooms, service closets and the like).
This product is not suitable for use with visual display work place devices accord-
•
ing to §2 of the the German Ordinance for Work with Visual Display Units.
Warnings and Precautions!
Rack Precautions
Ensure that the leveling jacks on the bottom of the rack are fully extended to •
the fl oor with the full weight of the rack resting on them.
In single rack installation, stabilizers should be attached to the rack.
•
In multiple rack installations, the racks should be coupled together.•
Always make sure the rack is stable before extending a component from it.•
You should extend only one component at a time - extending two or more si-•
multaneously may cause the rack to become unstable.
Server Precautions
Review the electrical and general safety precautions in Chapter 4.•
Determine the placement of each component in the rack • before you install the
rails.
Install the heaviest server components on the bottom of the rack fi rst, and then
•
work up.
Use a regulating uninterruptible power supply (UPS) to protect the server from
•
power surges, voltage spikes and to keep your system operating in case of a
power failure.
2-2
Chapter 2: Server Installation
Allow the hot plug SATA drives and power supply modules to cool before touch-•
ing them.
Always keep the rack's front door and all panels and components on the servers
•
closed when not servicing to maintain proper cooling.
•
Make sure all power and data cables are properly connected and not blocking
the chassis airfl ow. See Chapter 5 for details on cable connections.
Rack Mounting Considerations
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating temperature of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient temperature (Tmra).
Reduced Airfl ow
Equipment should be mounted into a rack so that the amount of airfl ow required
for safe operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connections other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).
2-3
SUPERSERVER 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F User's Manual
!
Removing the Protective Film
Before operating the SC827 chassis for the fi rst time, it is important to remove the
protective fi lm covering the top of the chassis, in order to allow for proper ventila-
tion and cooling.
Removing the Protective Film
Peel off the protective fi lm covering the top cover and the top of the chassis1.
Check that all ventilation openings on the top cover and the top of the chassis 2.
are clear and unobstructed.
Figure 2-1: Removing the Chassis Cover
1
1
Check Ventilation
Openings
2
1
Warning: Except for short periods of time, do NOT operate the server
without the cover in place. The chassis cover must be in place to allow proper airfl ow and prevent overheating.
2-4
Chapter 2: Server Installation
2-4 Rack Mounting Instructions
This section provides information on installing the SC827 chassis into a rack unit
with the quick-release rails provided. There are a variety of rack units on the market,
which may mean the assembly procedure will differ slightly. You should also refer to
the installation instructions that came with the rack unit you are using.
Note: This rail will fi t a rack between 26" and 33.5" deep.
Separating the Sections of the Rack Rails
The chassis package includes two rail assemblies in the rack mounting kit. Each
assembly consists of two sections: an inner fi xed chassis rail that secures directly
to the server chassis and an outer fi xed rack rail that secures directly to the rack
itself.
Figure 2-2. Separating the Rack Rails
1
1
2
1
3
1
4
1
Rail Assembly
Extending the Rails
Quick-
Release Tab
Separating
the Inner Rail
Extension
Separating the Inner and Outer Rails
Locate the rail assembly in the chassis 1.
packaging.
Extend the rail assembly by pulling it 2.
outward.
Press the quick-release tab.3.
Separate the inner rail extension from 4.
the outer rail assembly.
2-5
SUPERSERVER 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F User's Manual
Installing the Inner Rail Extensions
The SC827 chassis includes a set of inner rails in two sections: inner rails and inner
rail extensions. The inner rails are pre-attached to the chassis, and do not interfere
with normal use of the chassis if you decide not to use a server rack. The inner rail
extension is attached to the inner rail to mount the chassis in the rack.
Installing the Inner Rails
Place the inner rail extensions on the side of the chassis aligning the hooks 1.
of the chassis with the rail extension holes. Make sure the extension faces
"outward" just like the pre-attached inner rail.
Slide the extension toward the front of the chassis.2.
Secure the chassis with 2 screws as illustrated. Repeat steps for the other 3.
inner rail extension.
Figure 2-3. Installing the Inner Rail Extensions
3
1
1
1
2
1
3
1
2-6
Chapter 2: Server Installation
3
1
1
1
2
1
Figure 2-4: Assembling the Outer Rails
Outer Rack Rails
Outer rails attach to the rack and hold the chassis in place. The outer rails for the
SC827 chassis extend between 30 inches and 33 inches.
Installing the Outer Rails to the Rack
Secure the back end of the outer rail to the rack, using the screws provided. 1.
Press the button where the two outer rails are joined to retract the smaller 2.
outer rail.
Hang the hooks of the rails onto the rack holes and if desired, use screws to 3.
secure the front of the outer rail onto the rack.
Repeat steps 1-3 for the remaining outer rail.4.
2-7
SUPERSERVER 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F User's Manual
Figure 2-5: Installing Into the Rack
Installing the Chassis into a Rack
Extend the outer rails as illustrated above. 1.
Align the inner rails of the chassis with the outer rails on the rack.2.
Slide the inner rails into the outer rails, keeping the pressure even on both 3.
sides. When the chassis has been pushed completely into the rack, it should
click into the locked position.
Optional screws may be used to secure the to hold the front of the chassis to 4.
the rack.
2-8
Chapter 2: Server Installation
2-5 Checking the Serverboard Setup
After you install the system in the rack, you will need to access the inside of the
nodes to make sure the serverboard is properly installed and all the connections
have been made.
Accessing the Inside of a Node (Figure 2-6)
To remove a node, fi rst push the two latches (located near the handles) 1.
inward.
Grasp the handles and pull the node out from the rear of the chassis.2.
To remove the system from the rack completely, depress the locking tabs in 3.
the chassis rails (push the right-side tab down and the left-side tab up) to
continue to pull the system out past the locked position.
Checking the Components and Setup
You may have one or two processors already installed in each of the two 1.
serverboards. Each processor needs its own heatsink. See Chapter 5 for
instructions on processor and heatsink installation.
Your server system may have come with system memory already installed. 2.
Make sure all DIMMs are fully seated in their slots. For details on adding
system memory, refer to Chapter 5.
You can install four add-on cards to the system. See Chapter 5 for details on 3.
installing PCI add-on cards.
Make sure all power and data cables are properly connected and not blocking 4.
the chassis airfl ow. See Chapter 5 for details on cable connections.
2-9
SUPERSERVER 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F User's Manual
2-6 Preparing to Power On
Next, you should check to make sure the SATA drives and SATA backplane have
been properly installed and all connections have been made.
Checking the SATA drives
The SATA disk drives are accessable from the front of the server and can be 1.
installed and removed from the front of the chassis without removing the top
chassis cover.
Depending upon your system's confi guration, your system may have one or 2.
more drives already installed. If you need to install SATA drives, please refer
to Chapter 6.
Checking the Airfl ow
Airfl ow is provided by four 8-cm PWM fans and (for each serverboard) one air 1.
shroud. The system component layout was carefully designed to direct suffi cient cooling airfl ow to the components that generate the most heat.
Note that all power and data cables have been routed in such a way that they 2.
do not block the airfl ow generated by the fans.
Providing Power
Plug the power cords from the power supplies unit into a high-quality power 1.
strip that offers protection from electrical noise and power surges.
It is recommended that you use an uninterruptible power supply (UPS).2.
Finally, depress the power on button on the front of the chassis.3.
2-10
Chapter 2: Server Installation
Figure 2-6. Removing a Node from the System
2
1
1
2-11
SUPERSERVER 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F User's Manual
Notes
2-12
Chapter 3: System Interface
Chapter 3
System Interface
3-1 Overview
There are LEDs on the control panels and on the SATA drive carriers to keep you
constantly informed of the overall status of the system as well as the activity and
health of specifi c components. There are also two buttons on each control panel.
This chapter explains the meanings of all LED indicators and the appropriate response you may need to take. Note that the server has four control panels, one for
each serverboard (node) installed in the system. This allows each severboard to
be controlled independently of the other.
3-2 Control Panel Buttons
There are two push-buttons located on each control panel: a power on/off button
and a UID button.
Power
This is the main power button, which is used to apply or turn off the main system
power only to the node it is connected to. Depressing this button removes the main
power but keeps standby power supplied to the serverboard. This button has an
LED built into it, which will illuminate when its node is powered on.
UID
Depressing the UID (unit identifi er) button illuminates an LED on both the front and
rear of the chassis for easy system location in large stack confi gurations. The LED
will remain on until the button is pushed a second time. Another UID button on the
rear of the chassis serves the same function. This button has an LED built into it,
which will illuminate when either the front or rear UID button is pushed.
3-1
SUPERSERVER 6026TT-BT(R)F/BIBX(R)F/BIBQ(R)F User's Manual
3-3 Control Panel LEDs
In addition to the LEDs built into the power and UID buttons, each of the four control
panels located on the front of the SC827B-(R)1400B chassis has two LEDs that
provide you with critical information related their own node. This section explains
what each LED indicates when illuminated and any corrective action you may need
to take.
Overheat/Fan Fail
When this LED is solid on it indicates an overheat condition. When it fl ashes
quickly (~ once every second), it indicates a fan failure. When it fl ashes slowly (~
once every four seconds) it indicates a power supply failure. An overheat condition may be caused by cables obstructing the airfl ow in the system or the ambient
room temperature being too warm. Check the routing of the cables and make sure
all fans are present and operating normally. You should also check to make sure
that the chassis cover is properly installed. Finally, verify that the heatsinks are
installed properly (see Chapter 5). This LED will remain fl ashing or on as long as
the indicated condition exists.
NIC
Indicates network activity on any of the LAN ports when fl ashing
3-4 SATA Drive Carrier LEDs
Each SATA drive carrier has two LEDs.
Green:
• When illuminated, the green LED on the front of the SATA drive carrier
indicates drive activity. A connection to the SATA backplane enables this LED
to blink on and off when that particular drive is being accessed.
Red:
• There is no function associated with the red LED.
3-2
Loading...