Super Motor Company Super 25, Super 50, Super 100 User Manual

1

Manual

Super 25

Super 50

Super 100

2

FOREWORD

It is with great pleasure that we welcome you as a new
owner of a Super Motor Company product.
Further, we wish to thank you for selecting the Super
motorcycle.
This owner’s manual is a guide for the proper operation
and servicing of your Super motorcycle.
Read it thoroughly so that you will be able to maintain the
Super motorcycle in the best condition for your own riding
pleasure. Your Super motorcycle dealer will provide you
with a complete periodic inspection and furthermore, he is
always happy to assist you in case of a problem.
We wish you many kilometers of safe and happy
motorcycling.

3

CONTENTS

NOMENCLATURE 4

SERIAL NUMBER LOCATION 5

OPERATING INSTRUCTIONS

6

Instruments and indicator lights

7
Electrical controls 7
Mechanical controls 8
Fuel and oil 10
Pre-riding Inspection

11
Starting the engine 11
Break-in procedure 11
Riding the motorcycle

11
Brake 11
Parking 11

MAINTENANCE 12
Service schedule 15
Maintenance operations 16
Oil change

16
Spark plug cleaning and adjustment 16
Valve tappet clearance adjustment 17
Air cleaner service

18
Throttle adjustment 18
Carburetor Adjustment 18
Clutch Adjustment

18
Drive chain adjustment and lubrication 19
Brake inspection and adjustment 20
Battery service

21
Wheel removal 22
Headlight beam adjustment 22
Stop light switch adjustment 22
Light bulb replacement

22
Headlight bulb replacement procedure 22
Tail/stoplight bulb replacement procedure 23
Turn signal light bulb replacement procedure

23

TOOL KIT

24

SPECIFICATIONS

24

4

NOMENCLATURE

1 Speedometer
2 Front brake lever
3

Throttle grip

4 Turn signal light control switch
5 Rear brake pedal
6

Foot rests

7 Kick starter pedal
8 Pillion steps
9 Turn signal lights
10

Headlight beam selector switch

11 Horn button
12 Headlight control switch
13

Gear change pedal

14 Tail/stop light

1 Choke lever
2 Gear change pedal
3

Ignition switch

1

Kick starter pedal

2

Rear brake pedal

5

SERIAL NUMBER
LOCATION

The frame serial number 1 is stamped on the right side at
the frame center and the engine serial number 2 is located
on the crankcase directly above the step bar attaching
point.
These serial numbers are required when registering the
motorcycle.
Further, frame serial number must be indicated when pro­cessing the warranty claim and for ordering spare parts.

2 Engine serial number 1 Frame serial number

6

OPERATING INSTRUCTIONS

7

INSTURMENTS
AND INDICATOR
LIGHTS

The speedometer –1– is mounted on the top center of the
handlebars, within the speedometer assembly are incorpora­ted the odometer –2– and neutral indicator lamp –3–.
Neutral gear indicator is a green lamp located on the left
side of the dial plate and will be lit when the transmission
gear is in the neutral position, Gear speed range indica­tors –4– are curved bar shown on the speedometer dial
plate to indicate the recommended operating range of the
respective gears.

1

Speedometer

2

Odometer
3 Neutral indicator lamp
4 Gear speed range indicators
5

Fuel indicator

ELECTRICAL
CONTROLS

Ignition switch

The ignition switch is located on the right side of the
handlebar. Functions of the respective switch positions are
described below:
Inserting the ignition switch key –1– and turning to the
–3– will open the ignition circuit, permitting the engine to
be started and at the same time, the headlight and taillight
system circuits are also activated, permitting the use of the
headlight control switch.
Two sets of keys are provided with the motorcycle. Always
keep one set as a spare.

1

Ignition switch

2 “OFF”position
3

“ON”position

4 Ignition switch key

Headlight control
and beam selector switch

The headlight switch is located on the right handlebar.
The headlight beam selector switch is located on the left
handlebar.
Move the headlight control switch to the forward position
and turn on the headlight with the headlight beam selec­tor switch.–3– is low beam position (low beam light and
taillight on), –4– is the high beam position (high beam light
and taillight on).
The headlight will only operate when the ignition and
headlight control switches are in the “ON” positions.

Horn button

This is push button switch –5– located on the left handle
grip housing. While the horn button is depressed the horn
will operate.

1

Indicator

2 Indicator switch
3

Low beam
4 High beam
5 Horn

Indicator light control switch

Indicator light control switch –2– is mounted on the left
handle grip housing, for making a left turn, move the switch
to the < position, and to the > when making a right turn.

8

MECHANICAL
CONTROLS

Steering lock

The steering handle lock –1– is located directly below
the steering head. Steering handle can only be locked
in the left position, insert the key into the lock and turn
counterclockwise 180°.

1

The steering handle lock

Front brake lever

The front brake lever is located at the right handlebar.
Application of the front brake is effected by squeezing the
front brake lever with a force proportional to the braking
effort required.

2

Front brake lever

Stop light switch

The stop light switch operates the stop light when the rear
brake is applied.
The rear brake switch which is an adjustable plunger type
is located near the rear brake pedal (page 21).

1

Cutoff switch

2

Headlight switch

3 Electronic ignition switch

9

Gear lever

The gear change pedal –1– located near the left foot rest
is of the progressive shift, positive stop type, which means
one full stroke of the gear change pedal will shift only gear
position. The shifting sequence is arranged as shown in
the figure.

1

The gear change pedal

Shifting from the neutral position into 1st gear (low gear)
is performed by pressing the front end of the gear change
pedal with the toe. Shifting to 2nd and 3rd is performed by
progressively pressing the forward end of the pedal. Shifting
down to the lower gears is performed by progressively
pressing the rear end of the pedal. The transmissions
neutral position is located above 1st gear.

NOTE:
DURING ALL NORMAL GEAR CHANGES, THE THROTTLE MUST
BE MOMENTARILY CLOSED TO AVIOD EXCESSIVE ENGINE
R.P.M. AND UNDUE STRESS ON DRIVE TRAIN COMPONENTS.

Choke lever

The choke lever –1– is located at the left side of the
carburetor. When the choke lever is up, the choke valve is
fully open. (cold engine starting position). When the choke
lever is down, the choke is fully closed.

1

The choke lever

shift up shift up

gear shift sequence

N
1
2
3

Air filter

The air filter –2– is located in the middle of frame, assures
that only clean air enters the cylinder

2

The air filter box

10

FULE AND OIL

Fuel tank

The fuel tank –1– is located under the seat. The fuel tank
capacity is 3.8lit, .

NOTE:
PREMIUM GRADE FUEL WITH AND OCTANE RATING OF 95 OR
ABOVE MUST BE USED. DO NOT MIX OIL WITH THE FUEL.

Fuel valve

The fuel valve is located at the top of the carburetor. When
the fuel valve is in the “CLOSE” (forward) position, fuel
can not flow from the fuel tank to the carburetor. The fuel
valve should be set in this position when the motorcycle is
parked. Turning the fuel valve to the “OPEN” position allows
fuel to flow to the carburetor from the main fuel supply.

1

The fuel valve
2 “OPEN”position
3

“CLOSE”position

Engine Oil Recommendation

Use regular multigrade 10W-40 oil. The regular use of
special oil additives is unnecessary and will only increase
operating expenses.
Engine oil should be changed at the intervals prescribed in
the Maintenance Schedule on page 14-15.

NOTE:
ENGINE OIL IS A MAJOR FACTOR AFFECTING THE
PERFORMANCE AND SERVICE LIFE OF THE ENGINE. NON
DETERGENT AND LOW QUALITY OILS ARE SPECIFICALLY
NOT RECOMMENDED.

Viscosity

Viscosity selection should be based on the average
atmospheric temperature in your riding area. Change to
the proper viscosity oil whenever the average atmospheric
temperature changes substantially.
Recommended oil viscosity:
General, all temperatures

SAE 10W-40

Extreme, high temperatures SAE 20W-50

11

PRE-RIDING
INSPECTION

Prior to starting your motorcycle, it is advised that you
perform a general inspection as a matter of habit to make
sure that the motorcycle is in good safe riding condition.
This inspection will only require a few minutes and can save
you much time and expenses in the long run.
Check the following items and if adjustment or servicing is
necessary, refer to the appropriate section in the manual.

1

Engine oil level (page 16)

2 Fuel level (page 7)
3

Front and rear brakes (page 20)

4 Tire air pressure
5 Lighting system (page 7–8)
6

Rear drive chain (page 19)

7 Visually check the security of all controls, axles,
suspension and steering components.

STARTING THE ENGINE

Cold engine starting procedure

Follow the procedure outlined below.

1 Switch the fuel valve to the “OPEN” position.
2

Insert the ignition key into the switch and turn to the
“ON” position, check to make sure that the gear is in
neutral, the green indicator lamp will be lit.

3

Raise the choke lever to close the carburetor choke
valve.
4 Twist the throttle grip inward so that the throttle valve
is 1/8 to 1/4 open and push the red starter button on
the right handlebar. Push till the engine starts and
release the button.
5 Or twist the throttle grip inward so that the throttle
valve is 1/8 to 1/4 open and operate the kick starter
with the right foot, starting from the top of stroke and
following through to the bottom with a rapid and conti
nuous kick. Operate several times until engine starts.
6 If the engine fails to start after several repeated at
tempts turn the ignition switch OFF open the choke
valve by repositioning the lever to the lowered position,

turn the throttle grip to full throttle opening and then
operate the starter button or the kick starter several
times.
Next, position the ignition switch to “ON” and follow
the normal starting procedure, however, without the
use of the choke.
7 After the engine starts, operate for 2page3 minutes at
medium speed to warm up the engine.
8 When the engine is warm, place the choke lever in
the open position.

Starting in extreme cold weather

Prime the engine before starting by cranking the engine
several times using the kick starter and with ignition
switch OFF.
The choke should be fully closed and the throttle closed.
Follow with the procedure for starting a cold engine.

Starting warm engine

When the engine is to be restarted while it is still warm,
proceed as for a cold engine, however, the use of the
choke is not necessary.

BREAK-IN PROCEDURE

The motorcycle should not be exposed to severe or abusive
riding conditions. This precaution will be rewarded with
extra-long trouble free life of the motorcycle.
It is recommended that for the first 1.000km, the motorcycle
not be operated in excess of 80% of the maximum rpm in
the respective gears.

RIDING THE
MOTORCYCLE

After the engine has been warmed up, it is ready for
riding.
First, return the throttle grip to the idling position and
depress the front end of the gear change pedal to shift into
first gear. Increase the engine speed by twisting the throttle

grip inward.
When the motorcycle attains a speed of approximately
16kph (10mph), close the throttle and shift to the 2nd gear
by fully depressing the front end of gear change pedal
forward lightly with the toe.
This sequence is repeated to progressively shift into the
next higher gear, (Refer to page 9 for operation of gear
change pedal).

NOTE:
W

HEN SHIFTING GEARS EITHER UP OR DOWN, THE

THROTTLE MUST BE CLOSED.

BRAKE

Most important is to apply both the front and rear brakes
together. Independent application of either the front or rear
brake gently is possible, but if only one brake is applied
strongly, enough to lock the respective wheel, it can cause
loss of control of the motorcycle.
Both the front and rear brakes should be applied together
uniformly and gradually.
Further, engine compression may also be used for braking
without danger or causing damage to engine. So called
braking on the engine.

PARKING

Whenever parking the motorcycle, position the ignition
switch to the “OFF” position and remove the key. The
steering handle should also be locked to prevent the
motorcycle from theft, if it is to be left unattended. Switch
the fuel valve to the “CLOSE” position.

12

MAINTENANCE

13

14

SERVICE SCHEDULE

It is highly recommended that the periodical inspections be
performed on the scheduled mileage in order to maintain
your motorcycle in the peak of condition and be assured
of extended trouble free service. (Refer to chart) Your
Super dealer will assist you in performing the scheduled
maintenance work.
Follow mileage reading on the schedule in km’s according
to the indication of speedometer.

Service Required

Month

Mile

Kilomter

Months or Miles, whichever occurs rst

Page

Reference

First Second Third

Thereafter

Repeat Every

— 6 12 6 12

200 3.000 6.000 3.000 6.000

300 5.000 10.000 5.000 10.000

Engine Oil—change • Every 1,000 Miles • 16

Oil Filter—clean • • —
Axles nuts front and rear—check or adjust • • • • • —
Spark Plugs—clean and adjust or replace • • • • 16Stat
Starter motor —check or service • •

Ignition Timing—check or adjust • • • • —

Valve Tappet Clearance—check or adjust • • • • 17

Air Cleaner—clean and replace • • • • 18

Throttle Operation—check • • 18

Carburetor—check or adjust • • • 18

Fuel Valve Strainer—clean • • • —

Fuel Tank and Fuel Lines—check • • • —

Clutch—check or adjust • • • 19

Drive chain and sprockets—adjust and lubricate
or replace

• • • •

19

15

Service Required

Month

Mile

Kilomter

Months or Miles, whichever occurs rst

Page

Reference

First Second Third

Thereafter

Repeat Every

— 6 12 6 12

200 3.000 6.000 3.000 6.000

300 5.000 10.000 5.000 10.000

Front and Rear Brake—adjust • 20-21

Front and Rear Brake Shoes—check or replace • • —

Front and Rear Brake Links—check • • • —

Wheel rims and spokes—check • • • • —

Tires—check or replace • • • —

Front Fork —check and change • • • —

Steering Head Bearings—check or adjust • —

Steering Handle Lock—check for operation • —

Side Stand Spring—check • • • —

Battery power—check and replace

iif necessary

• • • • 21

Lights, Horn and Speedometers—check for

operation or adjust

• • • 7, 22-23

• •

•

16

MAINTENANCE
OPERATIONS

Oil change

The engine oil is the chief factor affecting the performance
and the service life of the engine. Therefore, the oil
recommended on page 11 should be used and the oil
always maintained at the proper level. Further, the oil
should be changed at the service schedule as shown on
page 14-15.
Perform the engine oil change in the following manner.
Drain the oil while the engine is still warm as this will assure
complete and rapid draining.

1

Filler cap dipstick

2 Lower level mark
3

Upper level mark

Spark plug cleaning and adjustment

LG A7RTC is used on these models. Servicing of the spark
plug is as follows.

1

Detach the high tension cord cap and remove
the spark plug with the spark plug wrench which is
provided in the tool kit.

2

Inspect the tip of the spark plug for deposits or
fouling condition.
Clean the spark plug with a spark plug cleaner,
however, if it is not available, clean the tip of the spark
plug with a stiff wire such as a pin to remove the
depostits, wash in gasoline and follow by drying with a
rag.

3

Adjust the spark plug gap to 0.6~0.7mm
(0.024~0.028 inch) with a thickness gauge.
The adjustment is made by bending the negative
(grounded) electrode.
4 When installing the spark plug, it should be first
screwed in finger tight and then torqued with the spark
plug wrench for further 1/2 to 3/4 turn.

NOTE:
1 DO NOT ATTEMPT TO DRY OR REMOVE SOOT FROM
THE SPARK PLUG BY BURNING.
2 DO NOT USE IMPROPER HEAT RANGE SPARK PLUG.

4 Oil drain plug

1 Remove the oil filler cap from the R. crankcase cover.
2 Place an empty container of adequate size under the

crankcase to catch the oil, and then remove the drain
plug with a 17mm~19mm wrench.
3 After the oil stops draining from the crankcase, operate
the kick starter several times to drain any oil which may
be left in the pockets.

4

When the oil has been completely drained, reinstall the
drain plug –4–, making sure that the O ring used on the
plug is in good condition.

5

Fill the crankcase through the oil filler opening with ap
proximately 0.7 lit. of recommended grade oil. Check
the oil level with the filler cap dipstick, however, when
making this check, does not screw in the cap. Oil level
should be between the upper –2– and lower –3– level
marks on the dipstick, when checking the oil make
certain the motorcycle is in upright and level position.

Note:
1 If the oil is below the lower level mark 3. on the dipstick add
oil up to the proper level before operating engine.
2 When operating the motorcycle in unusually dusty conditions,
it is recommended that the oil changes be performed at more
frequent intervals than that which is specified in the service
schedule; this will have a very beneficial effect on the engine.

17

Valve tappet clearance adjustment

Excessive valve tappet clearance will cause tappet noise,
and negative clearance will cause the valve damage and
low power.
Therefore, the valve tappet clearance should be maintained
properly. Perform the valve tappet clearance check at
initial 500km (300miles) and every 4500km (3000miles)
thereafter.

1

The valve tappet clearance must be checked when the
engine is cold.
Remove the point cover and tappet adjusting hole cap.
2 Rotate the flywheel counterclockwise until the “T”
mark 1. on the flywheel lines up with the timing index
mark 2. In this position, the piston
may either be on the compression or the exhaust
stroke. The adjustment must be made when the
piston is on top of the compression stroke when both
the inlet and exhaust valves are closed. This condition
can be determined by shifting the tappets with fingers
through the tappet adjusting holes. If the tappets are
free, it is an indication that the valves are closed and
the piston is on the compression stroke. If the tappets
are light and the valves are open, rotate the flywheel
360° and realign the “T” mark to the timing index mark.
Check the clearance of both valves by inserting the

0.05mm (0.002 in) thickness gauge provided in the
tool kit between the adjusting screw and the valve
stem.
If it is necessary to make an adjustment, loosen the
adjusting screw lock nut –3– and turn the adjusting
screw –5– so that the valve clearance will offer a slight
resistance when the thickness gauge –4– is inserted.
After completing the adjustment, tighten the adjusting
screw lock nut while holding the adjusting screw to
prevent it from turning. Finally, recheck the clearance
again to make sure that the adjustment has not been
disturbed.

Air filter service

When the filter is clogged with dust, it affects engine
performance and therefore, it should be cleaned
periodically. The air cleaner is a removable element type for
easy cleaning. Remove the air cleaner cover by loosening
air cleaner cover nut. Tap the element lightly and apply
compressed air from the inside of the air cleaner element.

18

Throttle adjustment

To adjust the play in the throttle cable system, slide back
the rubber sleeve –1– at the carburetor end of the throttle
cable and make the adjustment with the adjuster –2–.
Turning the adjuster counterclockwise will decrease the
play in the cable.
Turning the adjuster clockwise will increase the play.
After completing the adjustment, slide the rubber sleeve
completely over the end of the cable to prevent the entry of
water into the carburetor.

Carburetor adjustment

Perform the carburetor adjustment periodically at every
4500km (3000 miles).

1

After the engine is warmed up, adjust the carburetor.
Set the idling speed to 1100~1200 rpm, with the
throttle stop screw –1–.

2

Manipulate the air screw –2– to obtain the maximum
engine speed. (The standard air screw setting is
between 1.1/8 to 1.3/8.
3 Readjust the throttle stop screw if it is necessary to
reset the idling speed.

NOTE:
MALFUNCTION OF THE ENGINE DURING HIGH SPEED
CAN BE CAUSED BY A DEFECTIVE IGNITION SYSTEM
OR VALVES, DETERMINE THE CAUSE OF THE TROUBLE
BEFORE ATTEMPTING TO CORRECT THE CONDITION BY
ADJUSTING THE CARBURETOR.

Clutch adjustment

Super motorcycle incorporates an automatic centrifugal
clutch.
Perform the clutch adjustment by the following procedure.

1

Clutch must be adjusted with the engine shut off.

Loosen the clutch adjuster lock nut –1–.

2

Turn the adjuster clockwise about one whole turn; do

not turn excessively.
3 Next, slowly turn the adjuster –2– counterclockwise
and stop when the screw starts to turn heavy.

4

From this position, back off the adjuster in the
clockwise direction 1/8 to 1/4 turn, and then tighten
the clutch adjuster lock nut.

Check to make sure that the clutch operates properly after
adjustment.

1

The engine should start easily with the kick starter
without the clutch slipping.
2 When changing gear, the clutch operation should be
smooth and light, especially when shifting down in
gear to the neutral position.

19

Drive chain adjustment and lubrication

The condition of the rear drive chain will have considerable
effect on the transmission of power from the engine to the
rear wheel. If not properly maintained, the drive chain can
cause premature wear and damage to transmission and
rear wheel bearings and sprockets as well as to itself.
A properly adjusted and lubricated drive chain assures
safe, smooth and trouble free operation of the vital drive
system.

1

Drive chain adjustment

a. Place the motorcycle on a main stand and remove
the chain case peep hole cap –1–.

b. Move the chain up and down at this
minimum slack, midway point and check the total
movement. It should be no less than 10mm and
no more than 20mm (0.4~0.8 in.)
c. When adjustment is necessary , loosen the axle
nut –1– and sleeve nut –2–.
d. To reduce drive chain slack, each adjusting
nuts –6– in equally until correct chain slack
is achieved. Note the index marks –3– on both
the chain adjuster plates –4– and rear fork
side scale –4–. These marks assist in
attaining correct rear axle alignment. Tighten the
rear axle and sleeve nuts securely.

e. When steps a-d have been performed, again
rotate the rear wheel to recheck for correct drive
chain slack.
f. Readjust the rear brake as necessary to correct
for the repositioning of the rear wheel assembly.
g. Take the motorcycles of the main stand and
check chain slack while sitting on the machine.
Roll either forwards or backward far enough to be
certain there is no light spots.

2 Drive chain lubrication

a. Detach the drive chain by removing the retaining
clip with pliers. Do not bend or twist the clip.
When possible install a new master link.
b. Clean the chain thoroughly in a suitable solvent.
Rinse in clean solvent and allow drying. Inspect
the chain for wear (joint sloppiness), stiffness
and binding at the joints and broken or separated
rollers. If any of these conditions exist, the chain
should be replaced.
Also inspect sprocket teeth for wear. Never
install a new chain on badly worn sprockets or
install a badly worn chain on new sprockets.
Your SUPER dealer can help you determine the
condition of these items.

c. Use a quality chain lubricant to spray the
chain with. Let it dry for at least 10-15 minutes
before reinstalling the chain onto the sprockets.
d. Correctly route the drive chain onto the sprockets
using the rear sprocket to position the chain ends
while installing the master link, link side plate and
retaining clip. Note that the closed end of the
retaining clip must face the direction of forward
wheel rotation.
e. Adjust rear drive chain as described in steps a-g
page 19.

NOTE:
FOR QUICK CHAIN MAINTENANCE USE THE CHAIN
LUBRICANT AFTER EVERY 300-400 KILOMETERS. JUST
SPRAY IT ON WITHOUT DETACHING THE CHAIN. PUT THE
MOTORCYCLE ON THE CENTRE STAND, PUT THE GEARBOX
IN THE NEUTRAL POSITION, REMOVE THE CHAIN GUARD
AND APPLY THE LUBRICANT ONTO THE CHAIN WHILE
GENTLY ROTATING THE WHEEL BY HAND.

20

Brake inspection and adjustment

Brakes are items of personal safety and should always be
maintained in proper adjustment.

1

Front brake

a. Raise the front wheel off the ground by placing

a support block under the engine, spin the front
wheel by hand and measure the amount of the
front brake lever free play until the wheel starts to
take hold.
The lever free play is 10~20mm(0.4~0.8 in) at
the end of the brake lever and if the actual
measurement exceeds the range, adjust the
brake.
b. If adjustment is necessary, turning the front
brake adjusting nut –4– in the clockwise direction
will decrease the free play.

NOTE:
MAKE SURE THAT THE CUT-OUT ON THE ADJUSTING NUT
IS SEATED ON THE BRAKE ARM PIN AFTER THE FINAL
ADJUSTMENT HAS BEEN MADE.

1 Front wheel

2 Front brake lever
3

Lever free play

4 Front brake adjusting nut

2

Rear brake
a. Raise the rear wheel off the ground placing

motorcycle on the stand and check the free play
of the rear brake pedal before the brake starts to
take hold.
b. Nominal free play –1– is 15~20mm (0.6~0.8 in)
for the brake pedal. If adjustment is required,
make the adjustment with the adjusting nut
–2– the same manner as for the front brake.

1 Rear brake pedal

2

Rear brake adjusting nut

21

Battery Service

If the motorcycle is operated with an insufficient (low)
battery electrolyte level, sulfation and battery plate damage
may occur. Inspecting and maintaining the electrolyte
level is a simple, quick operation, therefore, it should be
performed frequently as indicated in the Service Schedule
(page 14-15)

1

The 12V-4AH battery 1. is mounted within the
frame center. Remove the battery cover and check
the battery electrolyte. The correct electrolyte level is
between the lower and upper level marks 3., 4. on the
battery case.
2 To correct the electrolyte level, remove the battery cell
caps from the cells needing level correction. For case
of cell level correction a small syringe or plastic funnel
should be used. Carefully add the proper amount of
distilled water to bring the electrolyte level of the cells
between the lower and upper marks.

1

Battery
2

Lower level marks
3 Upper level marks

For maximum battery performance and life, only distilled
water should be added, however, in an emergency situation
where electrolyte water or low and distilled water is not
available, drinking water or a low mineral content water can
be used. Reinstall the cell caps.

NOTE:
BATTERY REMOVAL MAY BE NECESSARY WHEN BATTERY
ELECTROLYTE (SPECIFICGRAVITY) READING IS BELOW
1,200, INDICATING THE NEED OF BATTERY RECHARGING,
OR WHEN THE BATTERY IS REMOVED FOR STORAGE.

3 Disconnect the ground (-) negative
cable connection and the positive(+) cable
last. Note the positioning of the cables, and the
battery mount rubber pads as well as the routing of the
battery vent tube. Before installing the battery,
clean the battery. Baking soda and water can be used
to remove any existing corrosion.
4 When considerable amount of night riding is
planned or if turn signal is used extensively, there
will be considerable drain on the battery. To adjust
the system to this condition, change the green
generator load from the red (normal change) connector
to the transparent covered connector (high charge).
This will provide a higher battery charging rate and
prevent possibility of battery becoming discharged.

NOTE:
1 ADD ONLY DISTILLED WATER TO THE BATTERY, NEVER
USE TAP WATER.
2 WHEN REPLACING THE BATTERY
INTO THE COMPARTMENT, MAKE SURE THAT THE
VENT TUBE OF THE BATTERY IS PROPERLY ATTACHED
TO AND NOT PINCHED OR BLOCKED.
3 IF UNUSUAL HIGH RATE OF BATTERY
ELECTROLYTE LOSS IS EXPERIENCED, CONSULT
YOUR SUPER DEALER FOR A CHECK.

Wheel removal

Removal of front and rear wheel is performed in the
following manner.

1

Front wheel

a. Raise the front wheel of the ground by putting the

motorcycle on the centre stand.
b. Remove speedometer cable and front brake
cable from the front brake panel assembly.

c. Remove the front axle nut.
d. Pull out the front axle and the front wheel can be

removed from the frame.

2

Rear wheel
a. Remove the chain guard..
b. Loosen the rear axle nut, sleeve nut, drive chain

adjusting nut and disconnect the drive chain at
the joint clip.
c. Remove the rear brake adjusting nut and remove
the rear brake rod from the brake arm.
d. Remove the rear torque arm bolt at the rear brake
panel.
e. Pull out the rear axle and the rear wheel can be
removed from the frame.

NOTE:
DURING REASSEMBLY, THE DRIVE CHAIN JOINT SHOULD
BE INSTALLED IN THE WAY THAT THE OPEN END WILL
FACE OPPOSITE TO THE DIRECTION OF ROTATION.

22

Headlight beam adjustment

Headlight can be adjusted vertically.
The vertical beam adjustment is made with the adjusting
screw –1– located at the bottom of the headlight rim.
Turning the adjusting screw in will focus the beam toward
longer distance ( higher beam).

1

Adjusting screw

Stoplight switch adjustment

Turning the stoplight switch adjusting nut –2– in the A
direction will turn on the stoplight early.

1

Stoplight switch

2 Adjusting nut

Light bulb replacement

When exchanging the light bulbs, always replace the bulb
with that of the specified type and rating. This is important
to prevent the electrical lighting circuit from malfunctioning.
The light bulbs are listed below.

Headlight bulb replacement procedure

a. Loosen the two cross screw at the bottom of the
headlight and remove the headlight rim.

b.

Remove the socket assembly by pushing down on the
socket and twisting counterclockwise to unhook from
the reflector.

c.

Pull the bulb out and replace.

1 Headlight bulb socket
2 Reflector

3 Headlight bulb

23

Tail/stoplight bulb
replacement procedure

a. Remove the two screws retaining the tail/stoplight
lens.

b.

Press the bulb –2– inward and twist to the left, and the

bulb can be removed.
c. When installing the taillight lens do not over tighten the
screw as this may damage the lens.

Turn signal light bulb
replacement procedure.

The bulb replacement is made in the same manner as for
the tail/stoplight bulb in the above paragraph.

1 Tail/stoplight bulb

24

SPECIFICATIONS

Model Super 25 & Super 50 Super 100

Price €1295,- (inc. VAT ) €1399,- (inc. VAT & BPM)

Wheelbase 1200mm 1200mm

Ground clearance 135mm 135mm

Minimum turning radius 1800mm 1800mm

Swing of steering handlebar 46 46

Caster angle 26.5 26.5

Curb weight 80kg 80kg

Payload 75kg 75kg

Fuel tank capacity 4.0L 4.0L

Lubricating oil charged 0.8L 0.8L

Eective circulating 0.6L 0.6L

Maximum speed 25 km/h - 45km/h 95km/h

Grade ability >18 >18

Engine model 139FMB, air cooling, 4-stroke 152FMH, air cooling, 4-stroke

Bore× stroke 39.0 mm × 41,4 mm 52.4v mm ×49.5 mm

Compression ratio 9.1:1 9.1:1

Piston displacement 49cc 107cc

Minimum steady idling speed 1200r/min 1200r/min

Fuel consumption rate 40g/KM-h 40g/KM-h

Gasoline Euro 95 Euro 95

Lubricating oil 15W/40 15W/40

Starting mode electric & kick start electric & kick start

Ignition mode CDI CDI

Spark plug A7RTC A7RTC

Valve clearance in and ex.0.05mm in and ex.0.03-0.05mm

Lubrication mode electric/kick start electric/kick start

TOOL KIT

The tool kit is contained in the left side cover. Minor
adjustment and parts replacement can be performed with
the tools contained in the kit. Adjustment or repairs which
cannot be performed with the tools in the kit should be
performed by your SUPER dealer.

Listed below are the items included in the tool kit.

1

10x14 mm open and wrench.

2 8x12 mm open and wrench.
3

Pliers

4 Spark plug wrench; For spark plug and axle nut.
5 No. 2 screwdriver
6

No. 2 cross point screwdriver

7 Screwdriver grip: for screwdriver
8

Tool bag

25

Type of clutch

Automatic

Automatic

Type of transmission 3 speed, shift, constant mesh

4 speed, shift, constant mesh

Front wheel tyre size 2.25-17-6PR 250kpa 2.25-17-6PR 250kpa

Rear wheel tyre size 2.50-17-6PR 250kpa 2.50-17-6PR 250kpa

Transmission gear ratio initial 4.059 initial 3.722

Battery 12V3A h 12V3A h

Transmission gear ratio initial 4.059 initial 3.722

1st gear 3.273/2.3564 3.272

2nd gear 1.939 1.939

3rd gear 1.350 1.350

4th gear 1.043

Final 2.733 2.733

Drive chain size 12.7 × 7.77× 6.35 12.7 × 7.77× 6.35

Storage battery 12V3A h 12V3A h

Spark plug model A7RTC A7RTC

Headlight specications 12V35W/35W 12V35W/35W

Turn signal lamp spec 12V10W 12V10W

Rear lamps spec 12V21W/5W 12V21W/5W

Neutral/tracator Pilot lamps 12V3.4W 12V3.4W

High beam pilot lamp 12V1.7W 12V1.7W

Dash light 12V1.7W 12V1.7W

Cartridge fuse 10A 10A

26

THERE MAY BE A SLIGHT DIFFERENCE BETWEEN
THE DESCRIPTION IN THIS MANUAL AND YOUR
MOTORCYCLE. THIS IS DUE TO THE MOTORCYCLE
BEING SPECIALLY DESIGNED TO CONFORM WITH
ALL THE REGULATIONS OF YOUR COUNTRY.
P

LEASE ADHERE TO THE MANUAL REGARDLESS OF

THE MINOR DIFFERENCES.

27

SUPER MOTOR COMPANY 2 YEAR LIMITED WARRANTY

SUPER MOTOR COMPANY warrants all parts of the vehicle except those listed under the caption “What is not covered” (See below). This warranty covers any repairs needed to correct defects in
materials or workmanship. SUPER MOTOR COMPANY is committed to producing the highest quality of motorcycles. All of our authorized dealers are dedicated to providing the best care and service
for your vehicle. We appreciate your business and value your feedback. You can reach us anytime at: www.supermotorcompany.com.

What you must do…
You must properly use, maintain and care for the vehicle as outlined in the SUPER MOTOR COMPANY owner’s manual. You must maintain a record of the vehicle’s required periodic service and
inspection. Periodic service and inspections are considered regular maintenance and are not reimbursable. Follow all safety instructions in your owner’s manual and read all warning labels carefully.
Remember to always wear safety gear when operating your scooter or motorcycle.

What your Authorized SUPER MOTOR COMPANY dealer must do…
Warranty repairs will be made at no charge for parts or labour. Any needed parts replacement will be made with new parts. Any implied warranty of merchantability and tness for a particular purpose
shall be limited to the duration of this written warranty. Your dealer will provide you with verbal instructions for operating your vehicle safely and will oer you the following safety equipment with your
purchase:

How long is the Warranty?
The warranty is eective as listed below or 12,000 kilometres (whichever comes rst) from the date of purchase by the original owner.

• Any damage resulting from negligence of the periodic maintenance;

• Any damage which results from repair, adjustment or maintenance operations by any methods other than
those specied by SUPER MOTOR COMPANY;

• Any damage which results from hard driving due to race, rally, or operation in a location not generally used for
driving;

• Any damage which results from use beyond the limitations specied in the SUPER MOTOR COMPANY
Operations Manual such as overloading the vehicle, or any damage from the use under abnormal conditions;

• Any damage caused when the product is used as a rental vehicle;

• Any damage which results from use of non-genuine parts or accessories or fuel, lubricant or uid not speci
ed by SUPER MOTOR COMPANY;

• Any damage due to improper storage or transport;

• Any damage which results from repair, adjustment or maintenance operations performed by any person other
than SUPER MOTOR COMPANY distributor or the Dealer;

• Any damage which results from modications of the product;

• Any damage that results from the passage of time (natural fading or painted surfaces, plated surfaces, sheet
peeling, corrosion, oxidization and other deterioration);

• Consumable replacement parts. SUPER MOTOR COMPANY will not warrant (after rst 500 kilometres)

parts worn due to natural wear and tear such as spark plugs, drive chains, air cleaners elements, brake
shoes, clutch disks, light bulbs batteries, fuses, rubber parts, tubes and tires, oils and cables;

• Any damage which results from unavoidable natural disasters, fire, collision, theft, and second damages
based on any of these occurrences;

• Sensational phenomena that do not affect performance or function of the product such as engine noise,
and vibration;

• Incidental or additional expenses incurred for making any claims such as those for towing, communications,
hotels and meals, as well as any losses during maintenance period, such as loss of time, loss of business,
and rental car expenses;

• Scheduled maintenance and inspections fees. I have read and understand this document including
coverage, exclusions, and requirements of the SuPER MOTOR COMPANy LIMITED WARRANTy. I have

been made aware of the risks and of the safety precautions that should be considered when operating a
scooter or motorcycle and are satisfied that proper instructions were provided and safety gear was offered at
the time of purchase.

Dealer Signature Customer Signature Date of Purchase

WHAT IS NOT COVERED? (WARRANTY EXCLUSIONS)

PHASE 1

All Parts covered

PHASE 1

Enigine & electric only

PHASE 1

Engine only

DAY S 365 540 730

Vehicle Identication Number: Model:

Dealer Name: Dealer Number:

Costumer Name: Warrenty Card Number:

Address: Postal Code:

Original owner: Telephone Number:

28