SUPER MICRO Computer 1018D-73MTF User Manual

SUPER

SUPERSERVER

1018D-73MTF

®

USER’S MANUAL

1.0

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu­mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTW ARE, OR DA TA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all
claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environ­ment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the manufacturer’s instruction manual, may cause harmful interference
with radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case you will be required to correct the interference at your own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warn­ing applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to the
State of California to cause birth defects and other repro­ductive harm.

Manual Revision 1.0
Release Date: June 13, 2013

Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.

Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2013 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the SuperServer 1018D-73MTF.
Installation and maintenance should be performed by experienced technicians only .

The SuperServer 1018D-73MTF is a high-end server based on the SC113MTQ­330CB 1U rackmount chassis and the Super X10SL7-F processor motherboard.

Manual Organization

Chapter 1: Introduction

Preface

The fi rst chapter provides a checklist of the main components included with the
server system and describes the main features of the X10SL7-F motherboard and
the SC113MTQ chassis.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer 1018D-73MTF
into a rack and check out the server confi guration prior to powering up the system.

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions and
information provided by the control panel on the chassis as well as other LEDs
located throughout the system.

Chapter 4: Standardized Warning Statements

You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 1018D-73MTF.

iii

SUPERSERVER 1018D-73MTF User's Manual

Chapter 5: Advanced Motherboard Setup

Chapter 5 provides detailed information on the X10SL7-F motherboard, including the
locations and functions of connections, headers and jumpers. Refer to this chapter
when adding or removing processors or main memory and when reconfi guring the
motherboard.

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the SC113MTQ server chassis. You
should follow the procedures given in this chapter when installing, removing or
reconfi guring SATA or peripheral drives and when replacing system power supply
modules and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed informa­tion on running the CMOS Setup Utility.

Appendix A: POST Error Beep Codes

Appendix B: System Specifi cations

iv

Notes

Preface

v

SUPERSERVER 1018D-73MTF User's Manual

Table of Contents

Chapter 1 Introduction

1-1 Overview .........................................................................................................1-1

1-2 Motherboard Features .....................................................................................1-2

Processors ......................................................................................................1-2

Memory ...........................................................................................................1-2

SAS .................................................................................................................1-2

SATA ................................................................................................................ 1-2

I/O Ports .......................................................................................................... 1-2

1-3 Server Chassis Features ................................................................................1-3

System Power ................................................................................................. 1-3

Control Panel .................................................................................................. 1-3

I/O Backplane .................................................................................................. 1-3

Cooling System ............................................................................................... 1-3

1-4 Contacting Supermicro ....................................................................................1-5

Chapter 2 Server Installation

2-1 Overview .........................................................................................................2-1

2-2 Unpacking the System .................................................................................... 2-1

2-3 Preparing for Setup .........................................................................................2-1

Choosing a Setup Location ............................................................................. 2-1

2-4 Warnings and Precautions .............................................................................. 2-2

Rack Precautions ............................................................................................ 2-2

Server Precautions .......................................................................................... 2-2

Rack Mounting Considerations .......................................................................2-3

Ambient Operating Temperature ................................................................ 2-3

Reduced Airfl ow .........................................................................................2-3

Mechanical Loading ................................................................................... 2-3

Circuit Overloading .....................................................................................2-3

Reliable Ground ......................................................................................... 2-3

2-4 Installing the System into a Rack ................................................................... 2-4

Identifying the Sections of the Rack Rails ...................................................... 2-4

Inner Rails ....................................................................................................... 2-5

Outer Rails ......................................................................................................2-6

Installing the Server into a Telco Rack ........................................................... 2-9

Chapter 3 System Interface

3-1 Overview .........................................................................................................3-1

vi

Table of Contents

3-2 Control Panel Buttons ..................................................................................... 3-1

Reset ...............................................................................................................3-1

Power ..............................................................................................................3-1

UID ..................................................................................................................3-1

3-3 Control Panel LEDs ........................................................................................3-2

NIC2 ................................................................................................................3-2

NIC1 ................................................................................................................3-2

HDD .................................................................................................................3-2

Power ..............................................................................................................3-2

Overheat/Fan Fail/UID LED ............................................................................3-3

3-4 Hard Drive Carrier LEDs ................................................................................. 3-3

Chapter 4 Standardized Warning Statements for AC Systems

4-1 About Standardized Warning Statements .......................................................4-1

Warning Defi nition ...........................................................................................4-1

Installation Instructions .................................................................................... 4-4

Circuit Breaker ................................................................................................ 4-5

Power Disconnection Warning ........................................................................ 4-6

Equipment Installation .....................................................................................4-8

Restricted Area ................................................................................................4-9

Battery Handling ............................................................................................ 4-10

Redundant Power Supplies ..........................................................................4-12

Backplane Voltage ........................................................................................ 4-13

Comply with Local and National Electrical Codes ........................................ 4-14

Product Disposal ........................................................................................... 4-15

Hot Swap Fan Warning ................................................................................. 4-16

Power Cable and AC Adapter ......................................................................4-18

Chapter 5 Advanced Motherboard Setup

5-1 Handling the Motherboard ..............................................................................5-1

Precautions .....................................................................................................5-1

Unpacking .......................................................................................................5-1

5-2 Processor and Heatsink Installation................................................................5-2

Installing an LGA 1150 Processor ................................................................... 5-2

Installing a CPU Heatsink ............................................................................... 5-4

5-3 Connecting Cables .......................................................................................... 5-5

Connecting Data Cables ................................................................................. 5-5

Connecting Power Cables ..............................................................................5-5

Connecting the Control Panel ......................................................................... 5-5

5-4 I/O Ports ..........................................................................................................5-6

vii

SUPERSERVER 1018D-73MTF User's Manual

5-5 Installing Memory ............................................................................................ 5-7

Memory Population Guidelines .......................................................................5-8

5-6 Adding PCI Cards ........................................................................................... 5-9

5-7 Motherboard Details ...................................................................................... 5-10

X10SL7-F Quick Reference ..........................................................................5-10

5-8 Connector Defi nitions ................................................................................... 5-12

5-9 Jumper Settings ............................................................................................5-19

5-10 Onboard Indicators ........................................................................................5-22

5-11 SAS/SATA Ports ............................................................................................ 5-23

5-12 Installing Software ......................................................................................... 5-24

SuperDoctor III .............................................................................................. 5-25

5-13 Onboard Battery ............................................................................................ 5-26

Chapter 6 Advanced Chassis Setup

6-1 Static-Sensitive Devices ..................................................................................6-1

Precautions .....................................................................................................6-1

6-2 Control Panel ..................................................................................................6-2

6-3 System Cooling ............................................................................................... 6-2

System Fan Failure .........................................................................................6-3

6-4 Drive Bay Installation/Removal .......................................................................6-4

Accessing the Drive Bays ...............................................................................6-4

Hard Drive Installation ..................................................................................... 6-4

DVD Drive Installation .....................................................................................6-6

6-5 Power Supply .................................................................................................. 6-8

Power Supply Failure ......................................................................................6-8

Chapter 7 BIOS

7-1 Introduction ...................................................................................................... 7-1

Starting BIOS Setup Utility .............................................................................. 7-1

How To Change the Confi guration Data .........................................................7-1

How to Start the Setup Utility .........................................................................7-2

7-2 Main Setup ...................................................................................................... 7-2

7-3 Advanced Setup Confi gurations......................................................................7-4

7-4 Event Logs .................................................................................................... 7-25

7-5 IPMI ............................................................................................................... 7-27

7-6 Boot Settings .................................................................................................7-29

7-7 Security Settings ...........................................................................................7-31

7-8 Save & Exit ................................................................................................... 7-32

Appendix A POST Error Beep Codes
Appendix B System Specifi cations

viii

Chapter 1: Introduction

Chapter 1

Introduction

1-1 Overview

The SuperServer 1018D-73MTF is a high-end server comprised of two main
subsystems: the SC113MTQ-330CB 1U server chassis and the X10SL7-F single
processor motherboard. Please refer to our web site for information on operating
systems that have been certifi ed for use with the system (www.supermicro.com).

In addition to the motherboard and chassis, various hardware components have
been included with the 1018D-73MTF, as listed below:

• Four sets of 4-cm counter-rotating fans (FAN-0065L4)

• One passive CPU heatsink (SNK-P0046P)

• One riser card for one PCI-E 3.0 x8 PCI add-on card in a PCI-E 3.0 x16 slot

(RSC-RR1U-E16)

• SATA Accessories

One SATA backplane (BPN-SAS-113TQ)
Eight 2.5" hard drive carriers (MCP-220-00047-0B)
Two sets of SATA cables (CBL-0186L)
Two SGPIO cables (CBL-0157L)

• One rackmount kit (CSE-PT52L)

1-1

SUPERSERVER 1018D-73MTF User's Manual

1-2 Motherboard Features

At the heart of the SuperServer 1018D-73MTF lies the X10SL7-F, a single proces­sor motherboard based on Intel's C222 chipset. Below are the main features of the
X10SL7-F (see Figure 1-1 for a block diagram of the chipset).

Processors

The X10SL7-F supports a single Intel® Xeon® E3-1200 v3 or a 4th Generation
Core i3/ i5/ i7 processor in an LGA1150 socket. Please refer to the motherboard
description pages on our web site for a complete listing of supported processors.

Memory

The X10SL7-F has four DIMM sockets that can support up to 32 GB of Unbuffered
ECC DDR3-1600/1333 memory. Please refer to Chapter 5 for installing memory.

SAS

An LSI 2308 SAS 2.0 controller is integrated into the X10SL7-F to provide eight
SAS ports.

SATA

An on-chip SATA controller is integrated into the X10SL7-F to provide two 6 Gb/sec
SATA 3.0 ports (RAID 0, and 1 supported) and four 3 Gb/sec SATA 2.0 ports (RAID
0, 1, 5 and 10 supported). RAID 5 is not supported with Linux.

I/O Ports

The I/O ports include one COM port, a VGA (monitor) port, four USB 2.0 ports and
two gigabit Ethernet ports. A dedicated IPMI LAN port is also included.

1-2

Chapter 1: Introduction

1-3 Server Chassis Features

The SC113MTQ-330CB is a short depth (20") 1U chassis that features eight 2.5"
hard drive bays and a high-effi ciency power supply. The following is a general outline
of the main features of the SC113MTQ-330CB chassis.

System Power

When confi gured as the SuperServer 1018D-73MTF, the SC113MTQ-330CB chas-
sis includes a single 330W high-effi ciency power supply.

Control Panel

The control panel on the SC113MTQ-330CB provides important system monitoring
and control information. LEDs indicate power on, network activity and hard disk
drive activity. Also present are a main power button and a system reset button.

I/O Backplane

The I/O backplane provides one PCI slots, one COM port, one VGA port, two USB
ports, two Ethernet (LAN) ports and a UID LED.

Cooling System

The chassis' revolutionary cooling design has been optimized to provide suffi cient
cooling for single CPU confi gurations. The chassis includes four 4-cm counter-
rotating, PWM (Pulse Width Modulated) fans located in the middle of the chassis.
Fan speed is controlled via IPMI.

1-3

SUPERSERVER 1018D-73MTF User's Manual

Figure 1-1. Intel C222 Chipset:

System Block Diagram

Note: This is a general block diagram. Please see Chapter 5 for details.

SAS2

6.0Gbps

8 SAS PORTS

PCIe x8 SLOT

4 SATA PORTS

2 SATA PORTS

2 USB PORTS

6 USB PORTS

TPM1.2 Header

FLASH
SPI 128Mb

PCIe x16 SLOT

LSI 2308

PCIe3.0_x8

PCIe3.0_x8

8.0Gb

VRM 12.5

MISC VRs

PCIe_x4

5.0Gbps

SATA-II

3.0Gbps

SATA-III

6.0Gbps

USB3.0

5.0Gbps

USB2.0

480Mbps

LPC

SPI

8.0Gb

SVID

i3/i5/i7 Processor

COM1,2

HEALTH
INFO

Intel

(H3)

Intel

PCH

5.0Gb

x4 DMI II

NCT6776D

LPC I/O

LPC

DDR3 (CHA)

1600/1333MHz

DDR3 (CHB)

1600/1333MHz

PCIe_x1

2.5Gbps
PCIe_x1

2.5Gbps

PCIe x1

LPC

GLAN1
I210

GLAN2
I210

ASPEED

ASP2400

RGMII

RTL8211E

PHY

RJ45

DIMM1
DIMM2(Far)

DIMM1
DIMM2(Far)

VGA

PORT

4 UDIMM

RJ45

RJ45

1-4

1-4 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)

Chapter 1: Introduction

Web Site:

Europe

Address: Super Micro Computer B.V.

Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

Asia-Pacifi c

Address: Super Micro Computer, Inc.

www.supermicro.com

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

[e-mail] (Technical Support)

[e-mail] (Customer Support)

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 23511

Taiwan (R.O.C)
Tel: [phone]
Fax: [phone]
Web Site:
Technical Support:
Email: [e-mail]
Tel: [phone]

www.supermicro.com.tw

1-5

SUPERSERVER 1018D-73MTF User's Manual

Notes

1-6

Chapter 2: Server Installation

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your SuperServer 1018D-73MTF
up and running. Following these steps in the order given should enable you to
have the system operational within a minimum amount of time. This quick setup
assumes that your SuperServer 1018D-73MTF system has come to you with the
processors and memory preinstalled. If your system is not already fully integrated
with a motherboard, processors, system memory etc., please turn to the relevant
chapter or section for details on installing specifi c components.

2-2 Unpacking the System

You should inspect the box the SuperServer 1018D-73MTF was shipped in and
note if it was damaged in any way. If the server itself shows damage you should
fi le a damage claim with the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the SuperServer 1018D­73MTF. It should be situated in a clean, dust-free area that is well ventilated. Avoid
areas where heat, electrical noise and electromagnetic fi elds are generated. You
will also need it placed near a grounded power outlet. Read the Rack and Server
Precautions in the next section.

2-3 Preparing for Setup

The box the SuperServer 1018D-73MTF was shipped in should include two sets of
rail assemblies, two rail mounting brackets and the mounting screws you will need to
install the system into the rack. Follow the steps in the order given to complete the
installation process in a minimum amount of time. Please read this section in its en­tirety before you begin the installation procedure outlined in the sections that follow.

Choosing a Setup Location

• Leave enough clearance in front of the rack to enable you to open the front door

completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for suffi cient airfl ow and ease in servicing.This product is for
installation only in a Restricted Access Location (dedicated equipment rooms,
service closets and the like).

2-1

SUPERSERVER 1018D-73MTF Manual

• This product is not suitable for use with visual display work place devices

acccording to §2 of the the German Ordinance for Work with Visual Display Units.

2-4 Warnings and Precautions

Rack Precautions

• Ensure that the leveling jacks on the bottom of the rack are fully extended to

the fl oor with the full weight of the rack resting on them.

• In single rack installation, stabilizers should be attached to the rack. In multiple

rack installations, the racks should be coupled together.

• Always make sure the rack is stable before extending a component from the

rack.

• You should extend only one component at a time - extending two or more si-

multaneously may cause the rack to become unstable.

Server Precautions

• Review the electrical and general safety precautions in Chapter 4.

• Determine the placement of each component in the rack before you install the

rails.

• Install the heaviest server components on the bottom of the rack fi rst, and then

work up.

• Use a regulating uninterruptible power supply (UPS) to protect the server from

power surges, voltage spikes and to keep your system operating in case of a
power failure.

• Allow the hot plug SATA drives and power supply modules to cool before touch-

ing them.

• Always keep the rack's front door and all panels and components on the servers

closed when not servicing to maintain proper cooling.

2-2

Chapter 2: Server Installation

Rack Mounting Considerations

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating tempera­ture of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient tempera­ture (Tmra).

Reduced Airfl ow

Equipment should be mounted into a rack so that the amount of airfl ow required
for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.

Circuit Overloading

Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connec­tions other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).

Warning! To prevent bodily injury when mounting or servicing this unit in a
rack, you must take special precautions to ensure that the system remains
stable. The following guidelines are provided to ensure your safety:

• This unit should be mounted at the bottom of the rack if it is the only unit in

the rack.

• When mounting this unit in a partially fi lled rack, load the rack from the bottom

to the top with the heaviest component at the bottom of the rack.

• If the rack is provided with stabilizing devices, install the stabilizers before

mounting or servicing the unit in the rack.

2-3

SUPERSERVER 1018D-73MTF Manual

2-4 Installing the System into a Rack

This section provides information on installing the SuperServer 1018D-73MTF into a
rack. If the 1018D-73MTF has already been mounted into a rack, you can skip ahead
to Sections 2-5 and 2-6. Note: The rails will fi t a rack between 26" and 33.5" deep.

There are a variety of rack units on the market, which may mean the assembly
procedure will differ slightly. The following is a guideline for installing the 1018D­73MTF into a rack with the rack rails provided. You should also refer to the instal­lation instructions that came with the rack unit you are using.

Identifying the Sections of the Rack Rails

Each assembly consists of two sections: an inner fi xed chassis rail that secures
directly to the server chassis and an outer fi xed rack rail that secures directly to
the rack itself.

Figure 2-1. Identifying the Sections of the Rack Rails

Inner Rail
Extensions

Inner Rails

Warning: do not pick up the server with the front handles. They are de-

signed to pull the system from a rack only.

2-4

Chapter 2: Server Installation

Inner Rails

The SC113MTQ chassis includes a set of inner rails in two sections: inner rails
and inner rail extensions. The inner rails are pre-attached and do not interfere with
normal use of the chassis if you decide not to use a server rack. Attach the inner
rail extension to stabilize the chassis within the rack.

Installing the Inner Rails (Figure 2-2)

1. Place the inner rack extensions on the side of the chassis aligning the hooks
of the chassis with the rail extension holes. Make sure the extension faces
"outward" just like the pre-attached inner rail.

2. Slide the extension toward the front of the chassis.

3. Secure the chassis with two screws as illustrated.

4. Repeat steps 1-3 for the other inner rail extension.

Figure 2-2. Installing Chassis Rails

1

2-5

2

3

SUPERSERVER 1018D-73MTF Manual

Outer Rails

Installing the Outer Rails to the Rack (Figures 2-3 and 2-4)

1. Attach the short bracket to the outside of the long bracket. You must align the
pins with the slides. Also, both bracket ends must face the same direction.

2. Adjust both the short and long brackets to the proper distance so that the rail
fi ts snugly into the rack.

3. Secure the long bracket to the front side of the outer rail with two M5 screws
and the short bracket to the rear side of the outer rail with three M5 screws.

4. Repeat steps 1-4 for the left outer rail.

Secure to the

Front of the Rack

Figure 2-3. Assembling the Outer Rails

Attach Outer Rails

Together

Secure to the

Rear of the Rack

Stability hazard. The rack stabilizing mechanism must be in place, or the
rack must be bolted to the fl oor before you slide the unit out for servicing.
Failure to stabilize the rack can cause the rack to tip over.

2-6

Chapter 2: Server Installation

3

3

2

Figure 2-4. Installing the Outer Rails to the Rack

2-7

SUPERSERVER 1018D-73MTF Manual

Installing the Chassis into a Rack (Figure 2-5)

1. Confi rm that chassis includes the inner rails and rail extensions . Also, confi rm
that the outer rails are installed on the rack.

2. Line chassis rails with the front of the rack rails.

3. Slide the chassis rails into the rack rails, keeping the pressure even on both
sides (you may have to depress the locking tabs when inserting). When the
server has been pushed completely into the rack, you should hear the locking
tabs "click".

4. (Optional) Insert and tightening the thumbscrews that hold the front of the
server to the rack.

Figure 2-5. Installing the Server into a Rack

2-8

Chapter 2: Server Installation

Installing the Server into a Telco Rack

To install the SuperServer 1018D-73MTF into a Telco type rack, use two L-shaped
brackets on either side of the chassis (four total). First, determine how far follow the
server will extend out the front of the rack. Larger chassis should be positioned to
balance the weight between front and back. If a bezel is included on your server,
remove it. Then attach the two front brackets to each side of the chassis, then the
two rear brackets positioned with just enough space to accommodate the width of
the telco rack. Finish by sliding the chassis into the rack and tightening the brackets
to the rack.

Figure 2-6. Installing the Server into a Telco Rack

2-9

SUPERSERVER 1018D-73MTF Manual

Notes

2-10

Chapter 3: System Interface

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the control panel to keep you constantly informed of the
overall status of the system as well as the three buttons described below.

3-2 Control Panel Buttons

There are three buttons located on the front of the chassis: a UIB button, a reset
button and a power on/off button.

UID

Depressing the UID (unit identifi er) button illuminates an LED on both the front and
rear of the chassis for easy system location in large stack confi gurations. The LED
will remain on until the button is pushed a second time. Another UID button on the
rear of the chassis serves the same function. This button has an LED built into it,
which will illuminate when either the front or rear UID button is pushed.

Reset

Use the reset button to reboot the system.

Power

This is the main power button, which is used to apply or turn off the main system
power. T urning off system power with this button removes the main power but keeps
standby power supplied to the system.

3-1

SUPERSERVER 1018D-73MTF Manual

3-3 Control Panel LEDs

The control panel located on the front of the SC113MTQ chassis has fi ve LEDs.
These LEDs provide you with critical information related to different parts of the
system. This section explains what each LED indicates when illuminated and any
corrective action you may need to take.

NIC2

Indicates network activity on LAN2 when fl ashing.

NIC1

Indicates network activity on LAN1 when fl ashing.

HDD

Indicates SATA and/or peripheral drive activity when fl ashing.

Power

Indicates power is being supplied to the system's power supply units. This LED
should normally be illuminated when the system is operating.

3-2

Chapter 3: System Interface

Overheat/Fan Fail/UID LED

When this L ED fl ashes it indicates a fan failure. When continuously on (not fl ashing)
it indicates an overheat condition, which may be caused by cables obstructing the
airfl ow in the system or t he ambi ent roo m temper ature bei ng too war m.

Check t he routin g of the ca bles and m ake sure that all f ans are pre sent and op ­erating n ormally. Als o check to make su re that the air s hrouds are in stalled an d
that the to p cover is o n. Finally, veri fy th at the heat sinks ar e insta lled pr oper ly.

This LED will rema in fl ashing or on as long as the overheat condition exists. When
used with a UID-compatible motherboard, the UID function is used to turn on or off
the blue light function of the the LED. Once the blue light is activated through the
system software, the unit can be easily located in very large racks and server banks.

3-4 Hard Drive Carrier LEDs

Each hard drive carrier has two LEDs.

• Green: When illuminated, the green LED on the front of the drive carrier in-

dicates drive activity. A connection to the SATA backplane enables this LED to
blink on and off when that particular drive is being accessed.

• Red: The red LED indicates two states. When blinking, it indicates the drive

is rebuilding. When solid, it indicates a drive failure. If a drive fails, you should
be notifi ed by your system management software. Please refer to Chapter 6 for
instructions on replacing failed drives.

3-3

SUPERSERVER 1018D-73MTF Manual

Notes

3-4

Chapter 4: Warning Statements for AC Systems

Chapter 4

Standardized Warning Statements for AC Systems

4-1 About Standardized Warning Statements

The following statements are industry standard warnings, provided to warn the user
of situations which have the potential for bodily injury. Should you have questions
or experience difficulty, contact Supermicro's Technical Support department
for assistance. Only certifi ed technicians should attempt to install or confi gure
components.

Read this appendix in its entirety before installing or confi guring components in the
Supermicro chassis.

These warnings may also be found on our web site at http://www.supermicro.com/
about/policies/safety_information.cfm.

Warning Defi nition

Warning!

This warning symbol means danger. You are in a situation that could cause bodily
injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents.

警告の定義

この警告サインは危険を意味します。

人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、

電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。

此警告符号代表危险。

您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前，必须充分
意识到触电的危险，并熟练掌握防止事故发生的标准工作程序。请根据每项警告结
尾的声明号码找到此设备的安全性警告说明的翻译文本。

此警告符號代表危險。

您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前，請注意觸
電的危險，並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號
碼找到相關的翻譯說明內容。

4-1

SUPERSERVER 1018D-73MTF User's Manual

ןונקת תורהצהאהרהז

Warnung
WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befi nden sich in einer Situation, die zu

Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den
Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung
vor Unfällen vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen
Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes

de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y
familiarícese con los procedimientos estándar de prevención de accidentes. Al
fi nal de cada advertencia encontrará el número que le ayudará a encontrar el texto
traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES.

IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une

situation pouvant entraîner des blessures ou des dommages corporels. Avant
de travailler sur un équipement, soyez conscient des dangers liés aux circuits
électriques et familiarisez-vous avec les procédures couramment utilisées pour
éviter les accidents. Pour prendre connaissance des traductions des avertissements
fi gurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fi n de chaque avertissement.

CONSERVEZ CES INFORMATIONS.

ןה תואבה תורהצהא ינפמ שמתשמה תא ריהזהל תנמ לע ,היישעתה ינקת יפ לע תורהז הלבח

ה וא תולאש שיו הדימב .תירשפא תיזיפי ,יהשלכ היעבב תולקתרוציל שי הכימת תקלחמ םע רשק

רידגהל וא ןיקתהל םיאשר דבלב םיכמסומ םיאנכט .ורקימרפוס לש תינכט תאה .םיביכר

תרדגה וא תנקתה ינפל ואולמב חפסנה תא

אורקל שי .ורקימרפוס יזראמב םיביכרה

4-2

Warning Statements for AC Systems

. ﻲﻓ ﻚﻧﺍ ﻥﺃ ﻦﻜﻤﻳ ﺔﻟﺎﺣ ﻲﻓ ﺐﺒﺴﺘﺗ ﺔﺑﺎﺻﺍ ﺔﻳﺪﺴﺟ ﺰﻣﺮﻟﺍ ﺍﺬﻫ ﻲﻨﻌﻳ ﺮﻄﺧ !ﺮﻳﺬﺤﺗ

ﻥﺃ ﻞﺒﻗ ﻱﺃ ﻰﻠﻋ ﻞﻤﻌﺗ ﺕﺍﺪﻌﻣ،ﻛﻢﻠﻋ ﻰﻠﻋ ﻦ ﻦﻋ ﺔﻤﺟﺎﻨﻟﺍ ﺮﻁﺎﺨﻤﻟﺎﺑ ﺮﺋﺍﻭﺪﻟﺍ

ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ

ﻛﻭﺔﻳﺍﺭﺩ ﻰﻠﻋ ﻦ ﺭﺎﻤﻤﻟﺎﺑﺕﺎﺳ ﺔﻴﺋﺎﻗﻮﻟﺍ ﻟ ﻊﻨﻤﻉﻮﻗﻭ ﻱﺃﺙﺩﺍﻮﺣ

ﻢﻗﺭ ﻡﺪﺨﺘﺳﺍ ﻥﺎﻴﺒﻟﺍ ﺹﻮﺼﻨﻤﻟﺍ ﺔﻳﺎﻬﻧ ﻲﻓ ﺮﻳﺬﺤﺗ ﻞﻛ ﺭﻮﺜﻌﻠﻟ ﺎﻬﺘﻤﺟﺮﺗ

안전을 위한 주의사항

경고!

이 경고 기호는 위험이 있음을 알려 줍니다. 작업자의 신체에 부상을 야기 할 수
있는 상태에 있게 됩니다. 모든 장비에 대한 작업을 수행하기 전에 전기회로와
관련된 위험요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준
작업절차를 준수해 주시기 바랍니다.

해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를
참조하십시오

BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die

lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken,
dient u zich bewust te zijn van de bij een elektrische installatie betrokken risico's
en dient u op de hoogte te zijn van de standaard procedures om ongelukken te
voorkomen. Gebruik de nummers aan het eind van elke waarschuwing om deze te
herleiden naar de desbetreffende locatie.

BEWAAR DEZE INSTRUCTIES

4-3

SUPERSERVER 1018D-73MTF User's Manual

Installation Instructions

Warning!

Read the installation instructions before connecting the system to the power source.

設置手順書

システムを電源に接続する前に、設置手順書をお読み下さい。

警告
将此系统连接电源前,请先阅读安装说明。

警告
將系統與電源連接前，請先閱讀安裝說明。

Warnung
Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen

lesen.

¡Advertencia!
Lea las instrucciones de instalación antes de conectar el sistema a la red de

alimentación.

Attention
Avant de brancher le système sur la source d'alimentation, consulter les directives

d'installation.

אורקל שי רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תאחתמ.

ﻟﺍ ﺕﺍﺩﺎﺷﺭﺇ ﺮﻗﺍﺐﻴﻛﺮﺘ ﻞﻴﺻﻮﺗ ﻞﺒﻗ ﻰﻟﺇ ﻡﺎﻈﻨﻟﺍ ﺔﻗﺎﻄﻠﻟ ﺭﺪﺼﻣ

시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오.

Waarschuwing
Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron

aansluit.

4-4

Chapter 4: Warning Statements for AC Systems

Circuit Breaker

Warning!

This product relies on the building's installation for short-circuit (overcurrent)
protection. Ensure that the protective device is rated not greater than: 250 V, 20 A.

サーキット・ブレーカー

この製 品 は、短絡（過電流）保護装置がある建物での設置を前提としています。

保護装置の定格が250V、20Aを超えないことを確認下さい。

警告
此产品的短路(过载电流)保护由建筑物的供电系统提供,确保短路保护设备的额定电
流不大于250V,20A。

警告
此產品的短路(過載電流)保護由建築物的供電系統提供,確保短路保護設備的額定電
流不大於250V,20A。

Warnung
Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss-

bzw. Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der
Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt.

¡Advertencia!
Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes)

del edifi cio. Asegúrese de que el dispositivo de protección no sea superior a: 250
V, 20 A.

Attention
Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit

dépend de l'installation électrique du local. Vérifi ez que le courant nominal du
dispositif de protection n'est pas supérieur à :250 V, 20 A.

ﺞﺘﻨﻤﻟﺍ ﺍﺬﻫ ﻰﻠﻋ ﺪﻤﺘﻌﻳ ﺕﺍﺪﻌﻣ ﺔﻳﺎﻤﺤﻟﺍ ﺓﺮﻴﺼﻘﻟﺍﺮﺋﺍﻭﺪﻟﺍ ﻦﻣ ﺎﻬﺘﻴﺒﺜﺗ ﻢﺗ ﻲﺘﻟﺍ ﻲﻓ

לע ךמתסמ הז רצומנגהה תעינמל םינבמב תנקתומה יכ אדוול שי .ילמשח רצק

רצקה ינפמ ןגמה רישכמה ילמשחהמ רתוי אל אוה-250 V, 20 A

ﻰﻨﺒﻤﻟﺍ

20A, 250V : ﻦﻣ ﺪﻛﺄﺗ ﻥﺃ ﻢﻴﻴﻘﺗ ﺯﺎﻬﺠﻟﺍ ﻟﺍﻲﺋﺎﻗﻮ ﺲﻴﻟ ﻦﻣ ﺮﺜﻛﺃ

4-5

SUPERSERVER 1018D-73MTF User's Manual

경고!

이 제품은 전원의 단락(과전류)방지에 대해서 전적으로 건물의 관련 설비에
의존합니다. 보호장치의 정격이 반드시 250V(볼트), 20A(암페어)를 초과하지
않도록 해야 합니다.

Waarschuwing
Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van

uw electrische installatie. Controleer of het beveiligde aparaat niet groter
gedimensioneerd is dan 220V, 20A.

Power Disconnection Warning

Warning!

The system must be disconnected from all sources of power and the power cord
removed from the power supply module(s) before accessing the chassis interior to
install or remove system components.

電源切断の警告
システムコンポーネントの取り付けまたは取り外しのために、シャーシー内部にアクセス

するには、
システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り

外す必要があります。

警告

在你打开机箱并安装或移除内部器件前,必须将系统完全断电,并移除电源线。

警告

在您打開機殼安裝或移除內部元件前，必須將系統完全斷電，並移除電源線。

Warnung
Das System muss von allen Quellen der Energie und vom Netzanschlusskabel

getrennt sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es
auf den Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder
zu entfernen.

4-6

Chapter 4: Warning Statements for AC Systems

ילמשח קותינ ינפמ הרהזא

!הרהזא

¡Advertencia!
El sistema debe ser disconnected de todas las fuentes de energía y del cable

eléctrico quitado de los módulos de fuente de alimentación antes de tener acceso
el interior del chasis para instalar o para quitar componentes de sistema.

Attention
Le système doit être débranché de toutes les sources de puissance ainsi que de

son cordon d'alimentation secteur avant d'accéder à l'intérieur du chassis pour
installer ou enlever des composants de systéme.

למשחה תורוקמ לכמ תכרעמה תא קתנל שי ריסהל שיו קפסהמ ילמשחה לבכ תא

נקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפלת רסה ואת .םיביכר

ﻞﺼﻓ ﺐﺠﻳ ﻡﺎﻈﻨﻟﺍ ﻊﻴﻤﺟ ﻦﻣﺭﺩﺎﺼﻣ ﺔﻗﺎﻄﻟﺍ ﺔﻟﺍﺯﺇﻭ ءﺎﺑﺮﻬﻜﻟﺍ ﻚﻠﺳ ﻦﻣ ﺓﺪﺣﻭ ﺩﺍﺪﻣﺍ

ﺔﻗﺎﻄﻟﺍ ﻞﺒﻗ

ﺯﺎﻬﺠﻟﺍ

경고!

시스템에 부품들을 장착하거나 제거하기 위해서는 섀시 내부에 접근하기 전에
반드시 전원 공급장치로부터 연결되어있는 모든 전원과 전기코드를 분리해주어야
합니다.

Waarschuwing
Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren

of verwijderen van systeem onderdelen, dient u alle spanningsbronnen en alle
stroomkabels aangesloten op de voeding(en) van de behuizing te verwijderen

ﻰﻟﺇ ﻝﻮﺻﻮﻟﺍ ﺔﻴﻠﺧﺍﺪﻟﺍ ﻖﻁﺎﻨﻤﻟﺍ ﻟﻞﻜﻴﻬﻠ ﺔﻟﺍﺯﺇ ﻭﺃ ﺖﻴﺒﺜﺘﻟ ﺕﺎﻧﻮﻜﻣ

4-7

SUPERSERVER 1018D-73MTF User's Manual

Equipment Installation

Warning!

Only trained and qualifi ed personnel should be allowed to install, replace, or service
this equipment.

機器の設置

トレーニングを受け認定された人だけがこの装置の設置、交換、またはサービスを許可
されています。

警告
只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。

警告
只有經過受訓且具資格人員才可安裝、更換與維修此設備。

Warnung
Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,

qualifi ziertem Personal gestattet werden.

¡Advertencia!
Solamente el personal califi cado debe instalar, reemplazar o utilizar este equipo.

Attention
Il est vivement recommandé de confier l'installation, le remplacement et la

maintenance de ces équipements à des personnels qualifi és et expérimentés.

!הרהזא

שר דבלב ךמסומ תווצתא ףילחהל ,ןיקתהל יא .דויצה רובע תוריש תתל וא דויצה

ﻦﻴﺑﺭﺪﻤﻟﺍﻭ ﻭ ﺐﻴﻛﺮﺘﻟﻝﺍﺪﺒﺘﺳﺍ ﻭﺃ ﺔﻣﺪﺧ ﺯﺎﻬﺠﻟﺍ ﺍﺬﻫ ﺢﻤﺴﻳ ﻥﺃ ﺐﺠﻳ ﻂﻘﻓ ﻦﻴﻠﻫﺆﻤﻟﺍ ﻦﻴﻔﻅﻮﻤﻠﻟ

경고!

훈련을 받고 공인된 기술자만이 이 장비의 설치, 교체 또는 서비스를 수행할 수
있습니다.

4-8

Chapter 4: Warning Statements for AC Systems

Waarschuwing
Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door

geschoold en gekwalifi ceerd personeel.

Restricted Area

Warning!

This unit is intended for installation in restricted access areas. A restricted access
area can be accessed only through the use of a special tool, lock and key, or other
means of security. (This warning does not apply to workstations).

アクセス制限区域
このユ ニットは 、アクセス制限区域に設置されることを想定しています。
アクセス制限区域は、特別なツール、鍵と錠 前、その他のセキュリティの手段を用いての

み出入りが可能です。

警告
此部件应安装在限制进出的场所，限制进出的场所指只能通过使用特殊工具、锁和
钥匙或其它安全手段进出的场所。

警告
此裝置僅限安裝於進出管制區域，進出管制區域係指僅能以特殊工具、鎖頭及鑰匙
或其他安全方式才能進入的區域。

Warnung
Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen.

Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und
Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich.

¡Advertencia!
Esta unidad ha sido diseñada para instalación en áreas de acceso restringido.

Sólo puede obtenerse acceso a una de estas áreas mediante la utilización de una
herramienta especial, cerradura con llave u otro medio de seguridad.

Attention
Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une

zone d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme
de verrouillage et une clé, ou tout autre moyen de sécurité.

4-9

SUPERSERVER 1018D-73MTF User's Manual

תלבגומ השיג םע רוזא

!הרהזא

תרזעב תנתינ השיגה .השיג תלבגה םהב שיש םירוזאב הדיחיה תא ןיקתהל שי

.('דכו לוענמ ,חתפמ) דבלב החטבא ילכ

. ﺺﻴﺼﺨﺗ ﺓﺪﺣﻮﻟﺍ ﻩﺬﻫ ﻲﻓ ﺎﻬﺒﻴﻛﺮﺘﻟ ﻖﻁﺎﻨﻣ ﺓﺭﻮﻈﺤﻣ ﻢﺗ

ﺻﻮﻟﺍ ﻦﻜﻤﻳﻰﻟﺇ ﻝﻮ ﺔﻘﻄﻨﻣ ﺓﺭﻮﻈﺤﻣ ﻂﻘﻓ ﻡﺍﺪﺨﺘﺳﺍ ﻝﻼﺧ ﻦﻣ ،ﺔﺻﺎﺧ ﺓﺍﺩﺃ

ﻭﺃ ﻱﺃ ﻼﻟ ﻯﺮﺧﺃ ﺔﻠﻴﺳﻭﻥﺎﻣﻷ ﺡﺎﺘﻔﻣﻭ ﻞﻔﻗ

경고!

이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다. 특수도구, 잠금 장치 및
키, 또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다.

Waarschuwing
Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang.

Toegang tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te
maken van speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.

Battery Handling

Warning!

There is the danger of explosion if the battery is replaced incorrectly. Replace the
battery only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's instructions

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池はメー
カーが推奨する型、または 同等のものを使用 下さい。使用済電池は製造元の指示に従

って処 分して 下さい。

警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更
换原有电池。请按制造商的说明处理废旧电池。

警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有
電池。請按照製造商的說明指示處理廢棄舊電池。

4-10

Chapter 4: Warning Statements for AC Systems

!הרהזא

Warnung
Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die

Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.

Attention
Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer

que par une pile de type semblable ou équivalent, recommandée par le fabricant.
Jeter les piles usagées conformément aux instructions du fabricant.

¡Advertencia!
Existe peligro de explosión si la batería se reemplaza de manera incorrecta.

Reemplazar la batería exclusivamente con el mismo tipo o el equivalente
recomendado por el fabricante. Desechar las baterías gastadas según las
instrucciones del fabricante.

תנכס תמייקץוציפ .הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי

גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ.

תוללוסה קוליס תושמושמה עצבל שי .ןרציה תוארוה יפל

ﺮﻄﺧ ﻙﺎﻨﻫ ﻦﻣ ﻝﺍﺪﺒﺘﺳﺍ ﺔﻟﺎﺣ ﻲﻓ ﺭﺎﺠﻔﻧﺍ ﺔﻳﺭﺎﻄﺒﻟﺍ ﺔﺤﻴﺤﺻ ﺮﻴﻏ ﺔﻘﻳﺮﻄﺑ ﻚﻴﻠﻌﻓ

ﺔﻳﺭﺎﻄﺒﻟﺍ ﻝﺍﺪﺒﺘﺳﺍ

ﻂﻘﻓ ﻉﻮﻨﻟﺍ ﺲﻔﻨﺑ ﺎﻬﻟﺩﺎﻌﻳ ﺎﻣ ﻭﺃ ﺎﻤﻛﺖﺻﻭﺃ ﺔﻌﻨﺼﻤﻟﺍ ﺔﻛﺮﺸﻟﺍ ﻪﺑ

ﺕﺎﻳﺭﺎﻄﺒﻟﺍ ﻦﻣ ﺺﻠﺨﺗ ﻟ ﺎﻘﻓﻭ ﺔﻠﻤﻌﺘﺴﻤﻟﺍﺔﻌﻧﺎﺼﻟﺍ ﺔﻛﺮﺸﻟﺍ ﺕﺎﻤﻴﻠﻌﺘ

경고!

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와
동일하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다.
제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.

Waarschuwing
Er is ontploffi ngsgevaar indien de batterij verkeerd vervangen wordt. Vervang de

batterij slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen
wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd
te worden.

4-11

SUPERSERVER 1018D-73MTF User's Manual

דחא קפסמ רתוי םייק םא

!הרהזא

Redundant Power Supplies

Warning!

This unit might have more than one power supply connection. All connections must
be removed to de-energize the unit.

冗長電源装置

このユニットは複数の電源装置が接続されている場合があります。

ユニットの電源を切るためには、すべての接続を取り外さなければなりません。

警告
此部件连接的电源可能不止一个，必须将所有电源断开才能停止给该部件供电。

警告
此裝置連接的電源可能不只一個，必須切斷所有電源才能停止對該裝置的供電。

Warnung
Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass

der Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.

¡Advertencia!
Puede que esta unidad tenga más de una conexión para fuentes de alimentación.

Para cortar por completo el suministro de energía, deben desconectarse todas las
conexiones.

Attention
Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute

tension et tout courant électrique de l'unité, toutes les connexions d'alimentation
doivent être débranchées.

.קפס לש דחא רוביחמ רתוי שי הדחיל תא ריסהל שיןקורל תנמ לע םירוביחה לכ

חיה תאי.הד

4-12

Chapter 4: Warning Statements for AC Systems

. ﺪﻗ ﺍﺬﻬﻟ ﻥﻮﻜﻳ ﻟﺍﺯﺎﻬﺠ ﺕﻻﺎﺼﺗﺍ ﺓﺪﻋ ﺕﺍﺪﺣﻮﺑ ﺔﻗﺎﻄﻟﺍ ﺩﺍﺪﻣﺍ

ﺔﻟﺍﺯﺇ ﺐﺠﻳ ﺕﻻﺎﺼﺗﻻﺍ ﺔﻓﺎﻛ ﻝﺰﻌﻟ ﻟﺍﺓﺪﺣﻮ ﻦﻋ ءﺎﺑﺮﻬﻜﻟﺍ

경고!

이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다. 이 장치에
전원을 차단하기 위해서는 모든 연결 단자를 제거해야만 합니다.

Waarschuwing
Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle

aansluitingen dienen verwijderd te worden om het apparaat stroomloos te maken.

Backplane Voltage

Warning!

Hazardous voltage or energy is present on the backplane when the system is
operating. Use caution when servicing.

バックプレーンの電圧
システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。

修理する際には注意ください。

警告
当系统正在进行时，背板上有很危险的电压或能量，进行维修时务必小心。

警告
當系統正在進行時，背板上有危險的電壓或能量，進行維修時務必小心。

Warnung
Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche

Spannungen oder Energien auf. Vorsicht bei der Wartung.

¡Advertencia!
Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso.

Tenga cuidado cuando lo revise.

Attention
Lorsque le système est en fonctionnement, des tensions électriques circulent sur

le fond de panier. Prendre des précautions lors de la maintenance.

4-13

SUPERSERVER 1018D-73MTF User's Manual

ירוחאה לנפב חתמ

ךלהמב רהזיהל שי .תכרעמה לועפת ןמזב ירוחאה לנפב חתמ תנכס תמייק

זא!הרה

.הדובעה

ﻙﺎﻨﻫ ﺮﻄﺧ ﻦﻣ ﻲﺋﺎﺑﺮﻬﻜﻟﺍ ﺭﺎﻴﺘﻟﺍ ﻰﻠﻋ ﺓﺩﻮﺟﻮﻤﻟﺍ ﺔﻗﺎﻄﻟﺍﻭﺃ ﺔﺣﻮﻠﻟﺍ

ﻥﻮﻜﻳ ﺎﻣﺪﻨﻋﻡﺎﻈﻨﻟﺍ ﻞﻤﻌﻳ ﺪﻨﻋ ﺍﺭﺬﺣ ﻦﻛ ﺔﻣﺪﺧ ﺯﺎﻬﺠﻟﺍ ﺍﺬﻫ

경고!

시스템이 동작 중일 때 후면판 (Backplane)에는 위험한 전압이나 에너지가 발생
합니다. 서비스 작업 시 주의하십시오.

Waarschuwing
Een gevaarlijke spanning of energie is aanwezig op de backplane wanneer het

systeem in gebruik is. Voorzichtigheid is geboden tijdens het onderhoud.

Comply with Local and National Electrical Codes

Warning!

Installation of the equipment must comply with local and national electrical codes.

地方および国の電気規格に準拠
機器の取り付けはその地方および国の電気規格に準拠する必要があります。

警告

设备安装必须符合本地与本国电气法规。

警告

設備安裝必須符合本地與本國電氣法規。

Warnung
Die Installation der Geräte muss den Sicherheitsstandards entsprechen.

¡Advertencia!
La instalacion del equipo debe cumplir con las normas de electricidad locales y

nacionales.

4-14

Chapter 4: Warning Statements for AC Systems

יצראה למשחה יקוח םואית

Attention
L'équipement doit être installé conformément aux normes électriques nationales

et locales.

!הרהזא

תנקתה םייצראהו םיימוקמה למשחה יקוחל תמאות תויהל תבייח דויצה.

ﺕﺍﺪﻌﻤﻟﺍ ﺐﻴﻛﺮﺗ ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﻠﻟ ﻞﺜﺘﻤﻳ ﻥﺃ ﺐﺠﻳ ﻦﻴﻧﺍﻮﻘﺔﻴﻨﻁﻮﻟﺍﻭ ﺔﻴﻠﺤﻤﻟﺍ ﺔﻘﻠﻌﺘﻤﻟﺍ

ءﺎﺑﺮﻬﻜﻟﺎﺑ

경고!

현 지역 및 국가의 전기 규정에 따라 장비를 설치해야 합니다.

Waarschuwing
Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale

elektriciteitsvoorschriften.

Product Disposal

Warning!

Ultimate disposal of this product should be handled according to all national laws
and regulations.

製品の廃棄

この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が
あります。

警告
本产品的废弃处理应根据所有国家的法律和规章进行。

警告
本產品的廢棄處理應根據所有國家的法律和規章進行。

Warnung
Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen

des Landes erfolgen.

4-15

SUPERSERVER 1018D-73MTF User's Manual

רצומה קוליס

¡Advertencia!
Al deshacerse por completo de este producto debe seguir todas las leyes y

reglamentos nacionales.

Attention
La mise au rebut ou le recyclage de ce produit sont généralement soumis à des

lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de
l'organisme compétent.

!הרהזא

ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס.הנידמה יקוח

ﻲﺋﺎﻬﻨﻟﺍ ﺺﻠﺨﺘﻟﺍ ﻦﻣ ﺞﺘﻨﻤﻟﺍ ﺍﺬﻫ ﻪﻌﻣ ﻞﻣﺎﻌﺘﻟﺍ ﻲﻐﺒﻨﻳ ﻟ ﺎﻘﻓﻭ ﻊﻴﻤﺠﺔﻴﻨﻁﻮﻟﺍ ﺢﺋﺍﻮﻠﻟﺍﻭ ﻦﻴﻧﺍﻮﻘﻟﺍ ﺪﻨﻋ

경고!

이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.

Waarschuwing
De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming

met alle nationale wetten en reglementen.

Hot Swap Fan Warning

Warning!

The fans might still be turning when you remove the fan assembly from the chassis.
Keep fi ngers, screwdrivers, and other objects away from the openings in the fan
assembly's housing.

ファン・ホットスワップの警告

シャーシから冷却ファン装置を取り外した際、ファンがまだ回転している可能性がありま

す。ファンの開口部に、指、ドライバー、およびその他のものを近づけないで下さい。

警告
当您从机架移除风扇装置，风扇可能仍在转动。小心不要将手指、螺丝起子和其他
物品太靠近风扇

4-16

Chapter 4: Warning Statements for AC Systems

警告
當您從機架移除風扇裝置，風扇可能仍在轉動。小心不要將手指、螺絲起子和其他
物品太靠近風扇。

Warnung
Die Lüfter drehen sich u. U. noch, wenn die Lüfterbaugruppe aus dem Chassis

genommen wird. Halten Sie Finger, Schraubendreher und andere Gegenstände
von den Öffnungen des Lüftergehäuses entfernt.

¡Advertencia!
Los ventiladores podran dar vuelta cuando usted quite ell montaje del ventilador

del chasis. Mandtenga los dedos, los destornilladores y todos los objetos lejos de
las aberturas del ventilador

Attention
Il est possible que les ventilateurs soient toujours en rotation lorsque vous retirerez

le bloc ventilateur du châssis. Prenez garde à ce que doigts, tournevis et autres
objets soient éloignés du logement du bloc ventilateur.

!הרהזא

יקלח תא םיריסמ רשאכ שי .םידבוע ןיידע םיררוואמהו ןכתי ,זראמהמ ררוואמה

קיחרהללררוואמה ךותב םיחתפהמ םינוש הדובע ילכו תועבצאה תא חוטב קחרמ

ﻦﻜﻤﻤﻟﺍ ﻦﻣ ﺡﻭﺍﺮﻤﻟﺍ ﻥﺃ ﻝﺍﺰﺗ ﻻ ﺔﻟﺍﺯﺇ ﺪﻨﻋﺭﻭﺪﺗ ﺔﻠﺘﻛ ﺔﺣﻭﺮﻤﻟﺍ ﻞﻜﻴﻬﻟﺍ ﻦﻣ ﺐﺠﻳ ءﺎﻘﺑﺇ

ﻊﺑﺎﺻﻷﺍ ﻭﻲﻏﺍﺮﺒﻟﺍ ﺕﺎﻜﻔﻣ

. ءﺎﻴﺷﻷﺍ ﻦﻣ ﺎﻫﺮﻴﻏﻭ ﺍﺪﻴﻌﺑ ﻦﻋ ﺕﺎﺤﺘﻔﻟﺍ ﻲﻓ ﺔﻠﺘﻛ ﺔﺣﻭﺮﻤﻟﺍ

경고!

섀시로부터 팬 조립품을 제거할 때 팬은 여전히 회전하고 있을 수 있습니다. 팬
조림품 외관의 열려있는 부분들로부터 손가락 및 스크류드라이버, 다른 물체들이
가까이 하지 않도록 배치해 주십시오.

Waarschuwing
Het is mogelijk dat de ventilator nog draait tijdens het verwijderen van het

ventilatorsamenstel uit het chassis. Houd uw vingers, schroevendraaiers
en eventuele andere voorwerpen uit de buurt van de openingen in de
ventilatorbehuizing.

4-17

SUPERSERVER 1018D-73MTF User's Manual

Power Cable and AC Adapter

Warning!

When installing the product, use the provided or designated connection cables,
power cables and AC adaptors. Using any other cables and adaptors could cause
a malfunction or a fi re. Electrical Appliance and Material Safety Law prohibits the
use of UL or CSA -certifi ed cables (that have UL/CSA shown on the code) for any
other electrical devices than products designated by Supermicro only.

電源コードとACアダプター

製品を設置する場合、提供または指定された接続ケーブル、電源コードとACアダプター
を使用下さい。他のケーブルやアダプタを使用すると故障や火災の原因になることがあ

ります。電気用品安全法は、ULまたはCSA認定のケーブル(UL/CSEマークがコードに表

記)をSupermicroが指定する製品以外に使用することを禁止しています。

警告
安装此产品时,请使用本身提供的或指定的连接线,电源线和电源适配器.使用其它线
材或适配器可能会引起故障或火灾。除了Supermicro所指定的产品,电气用品和材
料安全法律规定禁止使用未经UL或CSA认证的线材。(线材上会显示UL/CSA符号)。

警告
安裝此產品時,請使用本身提供的或指定的連接線,電源線和電源適配器.使用其它線
材或適配器可能會引起故障或火災。除了Supermicro所指定的產品,電氣用品和材
料安全法律規定禁止使用未經UL或CSA認證的線材。(線材上會顯示UL/CSA符號)。

Warnung
Bei der Installation des Produkts, die zur Verfügung gestellten oder benannt

Anschlusskabel, Stromkabel und Netzteile. Verwendung anderer Kabel und Adapter
kann zu einer Fehlfunktion oder ein Brand entstehen. Elektrische Geräte und
Material Safety Law verbietet die Verwendung von UL-oder CSA-zertifi zierte Kabel,
UL oder CSA auf der Code für alle anderen elektrischen Geräte als Produkte von
Supermicro nur bezeichnet gezeigt haben.

¡Advertencia!
Al instalar el producto, utilice los cables de conexión previstos o designados, los

cables y adaptadores de CA. La utilización de otros cables y adaptadores podría
ocasionar un mal funcionamiento o un incendio. Aparatos Eléctricos y la Ley de
Seguridad del Material prohíbe el uso de UL o CSA cables certifi cados que tienen
UL o CSA se muestra en el código de otros dispositivos eléctricos que los productos
designados por Supermicro solamente.

4-18

Chapter 4: Warning Statements for AC Systems

אתמו םיילמשחמ י

Attention
Lors de l'installation du produit, utilisez les bables de connection fournis ou désigné.

L'utilisation d'autres cables et adaptateurs peut provoquer un dysfonctionnement
ou un incendie. Appareils électroménagers et de loi sur la sécurité Matériel interdit
l'utilisation de UL ou CSA câbles certifi és qui ont UL ou CSA indiqué sur le code
pour tous les autres appareils électriques que les produits désignés par Supermicro
seulement.

AC

!הרהזא

AC רשא

םימאתמו םיקפס ,םילבכב שמתשהל שי ,רצומה תא םיניקתמ רשאכ

וא הלקתל םורגל לוכי רחא םאתמ וא לבכ לכב שומיש .ךכ םשל וקפוסו ודעונ

טב יקוחו למשח ירישכמב שומיש יקוח יפ לע .ילמשח רצק רוסיא םייק ,תוחי

UL ב וא- CSA לש דוק םהילע עיפומ ראשכ)

ב םיכמסומה םילבכב שמתשהל-

UL/CSA( רחא ילמשח רצומ לכ רובע.דבלב ורקימקרפוס ידי לע ןיוצ אלש

ﺐﻴﻛﺮﺗ ﺪﻨﻋ ﻡﺍﺪﺨﺘﺳﺍ ﺐﺠﻳ ﺯﺎﻬﺠﻟﺍ ﻭ،ﻞﻴﺻﻮﺘﻟﺍ ﺕﻼﺑﺎﻛ ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﺕﻼﺑﺎﻜﻟﺍ

ﺕﻻﻮﺤﻣﻭ ﺩﺩﺮﺘﻤﻟﺍ ﺭﺎﻴﺘﻟﺍ

. ﻥﺃ ﻱﺃ ﻡﺍﺪﺨﺘﺳﺍ ﺕﻼﺑﺎﻛ ﺕﻻﻮﺤﻣﻭ ﻯﺮﺧﺃ ﺐﺒﺴﺘﻳ ﻲﻓ ﻞﻄﻋ ﺙﻭﺪﺣ ﻖﻳﺮﺣ ﻭﺃ . ﻲﺘﻟﺍ

ﻚﻟ ﺎﻫﺮﻴﻓﻮﺗ ﻢﺗ ﺞﺘﻨﻤﻟﺍ ﻊﻣ

UL ﻭﺃ CSA ﺔﻴﺋﺎﺑﺮﻬﻜﻟﺍ ﺓﺰﻬﺟﻷﺍ ﺩﺍﻮﻣﻭ ﻥﻮﻧﺎﻗ ﺔﻣﻼﺴﻟﺍ ﻡﺍﺪﺨﺘﺳﺍ ﺮﻈﺤﻳ ﺕﻼﺑﺎﻜﻟﺍ

ﻞﺒﻗ ﻦﻣ ﺓﺪﻤﺘﻌﻣ

Supermicro ﺓﺰﻬﺟﺃ ﻯﺮﺧﺃ ﺔﻴﺋﺎﺑﺮﻬﻛ ﺮﻴﻏ ﺕﺎﺠﺘﻨﻤﻟﺍ ﺔﻨﻴﻌﻤﻟﺍ ﻞﺒﻗ ﻦﻣ ﻱﻷ

(UL/CSA ﻞﻤﺤﺗ ﻲﺘﻟﺍﺔﻣﻼﻋ )

경고!

제품을 설치할 때에는 제공되거나 지정된 연결케이블과 전원케이블, AC어댑터를
사용해야 합니다. 그 밖의 다른 케이블들이나 어댑터들은 고장 또는 화재의 원인이
될 수 있습니다. 전기용품안전법 (Electrical Appliance and Material Safety
Law)은 슈퍼마이크로에서 지정한 제품들 외에는 그 밖의 다른 전기 장치들을
위한 UL또는 CSA에서 인증한 케이블(전선 위에 UL/CSA가 표시)들의 사용을
금지합니다.

Waarschuwing
Bij het installeren van het product, gebruik de meegeleverde of aangewezen kabels,

stroomkabels en adapters. Het gebruik van andere kabels en adapters kan leiden
tot een storing of een brand. Elektrisch apparaat en veiligheidsinformatiebladen wet
verbiedt het gebruik van UL of CSA gecertifi ceerde kabels die UL of CSA die op
de code voor andere elektrische apparaten dan de producten die door Supermicro
alleen.

4-19

SUPERSERVER 1018D-73MTF User's Manual

Notes

4-20

Chapter 5: Advanced Motherboard Setup

Chapter 5

Advanced Motherboard Setup

This ch apter cover s the ste ps requi red to inst all pro ces sors a nd heats inks to the
X10SL7-F mother board, connect the data and power cables and install add-on
cards . All m other boa rd jump ers an d con nec tion s are des cri bed an d a layout and
quick re ference chart are included in this chapter. Remember to close the chassis
completely when you have fi nished wor king on the motherboard to protect and
cool the system suffi ciently.

5-1 Handling the Motherboard

Static electrical discharge can damage electronic com ponents. To prevent damage
to printed circuit boards, it is important to handle them very carefully (see Chapter

4). Also note that the size and weight of the motherboard can cause it to bend if
handled improperly, which may result in damage. To prevent the motherboard from
bending, keep one hand under the center of the board to support it when handling.

The following measures are generally suffi cient to protect your equipment from
static discharge.

Precautions

• Use a grounded wrist strap designed to prevent static discharge.

• Touch a grounded metal object before removing any board from its antistatic

bag.

• Handle a board by its edges only; do not touch its components, peripheral chips,

memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the motherboard, add-on cards and peripherals back into their antistatic

bags when not in use.

Unpacking

The motherboard is shipped in antistatic packaging to avoid static damage. When
unpacking the board, make sure the person handling it is static protected.

5-1

SUPERSERVER 1018D-73MTF User's Manual

5-2 Processor and Heatsink Installation

Warning: When handling the processor package, avoid placing direct pressure on the

label area of the fan.

Notes:

• Always connect the power cord last and always remove it before adding, re-

moving or changing any hardware components. Make sure that you install the
processor into the CPU socket before you install the CPU heatsink.

• If you buy a CPU separately, make sure that you use an Intel-certifi ed multi-

directional heatsink only.

• Make sure to install the motherboard into the chassis before you install the

CPU heatsinks.

• When receiving a motherboard without a processor pre-installed, make sure that

the plastic CPU socket cap is in place and none of the socket pins are bent;
otherwise, contact your retailer immediately.

• Refer to the Sup ermi cro web s ite for upd ates on CPU su ppor t.

Installing an LGA 1150 Processor

1. Press the load lever to release
the load plate covering the CPU
socket from its locked position.

2. Gently lift the socket clip to open
the load plate.

3. Hold the plastic cap at its north
and south center edges to remove
it from the CPU socket.

4. After removing the plastic cap,
hold the CPU at the north and
south center edges with your
thumb and index fi nger,.

5-2

5. Align the CPU key, which is a semi­circle cutout, against the socket
key, which is the notch below the
gold color dot on the side of the
socket.

6. Align pin 1 of the CPU against pin 1
of the CPU socket.

7. Once both CPU and the socket are
aligned, carefully lower the CPU
straight down into the socket. (To
avoid damaging the CPU or the
socket, do not rub the CPU against
the surface of the socket or its
pins.)

Chapter 5: Advanced Motherboard Setup

CPU Key

CPU Pin 1

8. With the CPU inside the socket,
inspect the four corners of the CPU
to make sure that the CPU is prop­erly installed.

9. Once the CPU is securely seated
on the socket, lower the CPU load
plate to the socket.

10. Use your thumb to gently push the
socket clip down to the clip lock.

Warning: Please save t he plastic ca p.
The moth er bo ard mu st be s hipp ed w ith
the plastic cap properly installed to
protect t he CPU soc ket pins. Shipm ent
without the plastic cap properly installed
will cause damage to the socket pins.

5-3

SUPERSERVER 1018D-73MTF User's Manual

Installing a CPU Heatsink

1. Remove power from the system and unplug the AC power cord from the
power supply.

2. Do not apply any thermal grease to the heatsink or the CPU die; the required
amount has already been applied.

3. Place the heatsink on top of the CPU so that the four mounting holes are
aligned with those on the (preinstalled) heatsink retention mechanism.

4. Screw in two diagonal screws (i.e. the #1 and the #2 screws) until just snug.
Do not fully tighten the screws or you may damage the CPU.)

5. Add the two remaining screws then fi nish the installation by fully tightening all
four screws.

Figure 5-1. Installing/Removing the Heatsink

Loosen screws in the
sequence shown

Screw #1

Motherboard

Screw #4

Screw #2

Screw #3

5-4

Chapter 5: Advanced Motherboard Setup

5-3 Connecting Cables

Now that the processors are installed, the next step is to connect the cables to the
motherboard. These include the data (ribbon) cables for the peripherals and control
panel and the power cables.

Connecting Data Cables

The cables used to transfer data from the peripheral devices have been carefully
routed in preconfi gured systems to p r eve nt t h e m from blockin g t h e fl ow of cooling
air that moves through the system from front to back. If you need to disconnect any
of these c a bles, you shou l d take care to rero ute them as they were originally after
reconnecti n g them (make sure the red wires connec t t o the pin 1 location s). If you
are confi guring the syst em, keep th e air fl ow in mind when routing the cables.
The following data cables (with their motherboard connector locations noted)
should be connected.
See the m other board l ayout diagr am in thi s chapter f or co nnecto r loc ation s.

• Control Panel cable (JF1, see next page)

• SAS or SATA cables (L-SAS0 through L-SAS7 or I-SATA0 through I-SATA5)

• SGPIO cables (6-SGPIO 1/2 and T-SGPIO 1/2 to SATA backplane)

Connecting Power Cables

The X10SL7-F has a 24 -pi n prima ry po wer supply c onnec tor des ignated "JPW1"
for con nec ti on to th e ATX power supp ly. Conne ct th e app ropr iate c on nec tor f rom
the power supply to JPW1 to supply power to the motherboard. See the Connector
Defi nitions s ecti on in thi s chapter f or power c onne ctor pi n defi nitions.

In addition, your power supply must be connected to the 8-pin Processor Power
connector at JPW2.

Connecting the Control Panel

JF1 contains header pins for various front control panel connectors. See Figure 5-1
for the pin locations of the various front control panel buttons and LED indicators.
Please note that even and odd numbered pins are on opposite sides of each header.

All JF1 wires have been bundled into single keyed ribbon cable to simplify their con­nection. Connect one end of this cable to JF1 and the other end to the Control Panel
printed circuit board, located just behind the system status LEDs in the chassis.

See the Connector Defi nitions section in this chapter for details and pin descrip-
tions of JF1.

5-5

SUPERSERVER 1018D-73MTF User's Manual

Figure 5-2. Front Control Panel Header Pins (JF1)

1920

Ground

NMI

X

Power LED

HDD LED

NIC1 LED

NIC2 LED

OH/Fan Fail LED

PWR Fail LED

Ground

Ground

2

1

X

Vcc

Vcc

Vcc

Vcc

Vcc

Vcc

Reset

PWR

Reset Button

Power Button

5-4 I/O Ports

The I/O ports are color coded in conformance with the PC 99 specifi cation. See
Figure 5-3 below for the colors and locations of the various I/O ports.

Figure 5-3. Rear Panel I/O Ports

1

4

1

6

1

1

1

3

1

2

1. COM1 6. USB Port 5 (2.0)

2. USB Port 2 (2.0) 7. LAN1

3. USB Port 3 (2.0) 8. LAN2

4. IPMI LAN 9. VGA

5. USB Port 4 (2.0)

1

5

I/O Ports

1

7

1

8

1

9

5-6

Chapter 5: Advanced Motherboard Setup

5-5 Installing Memory

Note: Check the Supermicro web site for recommended memory modules.

CAUTION

Exercise extreme care when installing or removing DIMM modules

to prevent any po ssibl e damage.

Installing DIMMs

Insert the desired number of DIMMs into the memory slots, starting with the
DIMMA1 slot.

1. Push the release tabs outwards on both ends of the DIMM slot to unlock it.

2. Align the key on the DIMM module with the receptive point on the slot.

3. Use two thumbs together to press both ends of the module straight down into
the slot until the module snaps into place.

4. Press the release tabs to the lock positions to secure the DIMM module into
the slot. See Figure 5-4.

Memory Support

The X10SL7-F supports up to 32 GB of Unbuffered ECC DDR3-1600/1333 memory ..

Figure 5-4. Installing DIMM into Slot

Notch

To In stal l : Inser t module

vert ic ally a nd pre ss
down unt il it sn aps in to
place. Pay a tte ntio n to
the ali gnme nt notc h at
the bottom.

To Remove:

Use your thumbs to
gently push the release
tabs near both ends of
the module. This should
release it from the slot.

Release Tab

Note: Notch should
align with the recep­tive key point on
the slot.

Front View

Release Tab

Notch

Top View of DDR3 Slot

5-7

SUPERSERVER 1018D-73MTF User's Manual

Memory Population Guidelines

Please follow the table below when populating the X10SL7-F.

DDR3 Unbuffered ECC (UDIMM) Memory

DIMM Slots per

Channel

21

22

DIMMs Populat-

ed per Channel

DIMM Type POR Speeds

Unbuffered

DDR3

Unbuffered

DDR3

1333, 1600 Single Rank, Dual Rank

1333, 1600 Single Rank, Dual Rank

Ranks per DIMM (any

combination)

Notes

• Be sure to use memory modules of the same type, same speed, same frequency

on the same motherboard. Mixing of memory modules of different types and
speeds is not allowed.

• Due to memory allocation to system devices, the amount of memory that

remains ava ilable for ope rational use w ill be reduce d when 4 GB of R AM is
used. Th e reduct ion in mem ory ava ilabili ty is dis propo rti onal. See t he follo w­ing tab le for det ails.

• For Microsoft Windows users: Microsoft implemented a design change in the

Windows XP with Service Pack 2 (SP2) and Windows Vista. This change is spe­cifi c to the behavior of Physical Address Extension (PAE) mode which improves
driver compatibility. For more information, please read the following article at
Microsoft’s Knowledge Base website at: http://support.microsoft.com/kb/888137.

Possible System Memory Allocation & Availability

Physical Memory

System Device Size

Firmware Hub fl ash memory (System BIOS) 1 MB 3.99
Local APIC 4 KB 3.99
Area Reserved for the chipset 2 MB 3.99
I/O APIC (4 Kbytes) 4 KB 3.99
PCI Enumeration Area 1 256 MB 3.76
PCI Express (256 MB) 256 MB 3.51
PCI Enumeration Area 2 (if needed) -Aligned on 256-MB

boundary­VGA Memory 16 MB 2.85
TSEG 1 MB 2.84

512 MB 3.01

Remaining (-Available)

(4 GB Total System

Memory)

Memory available to OS and other applications 2.84

5-8

Chapter 5: Advanced Motherboard Setup

5-6 Adding PCI Cards

PCI Expansion Slots

One riser card is used to support a PCI expansion (add-on) card in the system. The
SC113MTQ chassis can accommodate one standard size (full height full length)
PCI expansion card. When viewed from the chassis front, the card installs to the
left rear of the system.

PCI Card Installation

Before installing a PCI add-on card, make sure it is supported by the riser card.
Begin by releasing the locking tab that corresponds to the slot you wish to populate.
Insert the expansion card into the riser card by pushing down with your thumbs
evenly on both sides of the card.

PCI Slot/Card Confi gurations

Riser Card Expansion card supported

RSC-RR1U-E16 (pre -ins talle d) 1x PCI- E 3.0/ 2.0 x16 car d

5-9

SUPERSERVER 1018D-73MTF User's Manual

5-7 Motherboard Details

Figure 5-5. SUPER X10SL7-F Layout

USB4/5

JPUSB1

JPL1

IPMI

IPMI CODE

DIMMA1

FAN3

USB2/3

_LAN

DIMMA2

FAN2

COM2

DIMMB1

FAN1

COM1

JSTBY1

DIMMB2

JWD1

FAN4

JPW2

JPW1

JF1

Front Panel CTRL

LE3

JOH1

JPI2C1

JLED1

LE4

SW1

VGA

BAR CODE

MAC CODE

SAS CODE

J21

LAN2

LAN
CTRL

LAN1

JPL2

LAN
CTRL

JPB1

JBR1

JPG1

JPME1

JPME2

SPKR1
J3

LE5

J18

J19

LE6

BMC

CPU SLOT6 PCI-E 3.0 X8 (IN X 16)

PCH SLOT5 PCI-E 2.0 X4 (IN X 8)

JI2C1

JI2C2

JTPM1

X10SL7-F

CPU1

Rev. 1.01

CPU

LEDS2

JPS1

USB0 (3.0)

BIOS

USB8/9

Battery

JSD1

I-SATA0

I-SATA2

I-SATA4

FANA

I-SATA1

JBT1

I-SATA3

I-SATA5

JL1

PCH

USB1 (3.0)

BIOS

LICENSE

6-SGPIO2

6-SGPIO1

SAS
CTRL

T-SGPIO1

T-SGPIO2

L-SAS6

L-SAS4
L-SAS2 L-SAS3
L-SAS0 L-SAS1

L-SAS7
L-SAS5

X10SL7-F Quick Reference

Jumper Description Default Setting

JBT1 CMOS Clear See Section 5-9

2

C1/JI2C2 SMB to PCI-E Slots Pins 2-3 (Disabled)

JI
JPG1 VGA Enable/Disable Pins 1-2 (Enabled)
JPL1/JPL2 LAN1/LAN2 Enable/Disable Pins 1-2 (Enabled)
JPME1 ME Recovery Pins 1-2 (Normal)
JPME2 Manufacture Mode Select Pins 1-2 (Normal)
JPS1 SAS Enable/Disable Pins 1-2 (Enabled)
JPUSB1 USB 4/5 Wake Up Enable/Disable Pins 1-2 (Enabled)
JWD1 Watch Dog Enable/Disable Pins 1-2 (Reset)

5-10

Chapter 5: Advanced Motherboard Setup

Connector Description

COM1/COM2 COM1 (Port)/COM2 (Header)
Fan1 - Fan4,

FanA

System/CPU Fan Headers

JF1 Front Panel Control Header
JL1 Chassis Intrusion Header
JLED1 Power LED Indicator Header

2

JPI

C1 Power SMB (System Management Bus)
JPW1 24-pin ATX Main Power Connector (Required)
JPW2 +12V 8-pin CPU power Connector (Required)
JSD1 SATA DOM (Device On_Module) Power Connector
JSTBY1 Standby Power Header
JTPM1 Trusted Platform Module/Port 80 Connector
LAN1/LAN2 Gigabit (RJ45) Ports (LAN1/2)
IPMI_LAN IPMI_Dedicated LAN
I-SATA0-1 (Intel PCH) SATA 3.0 Ports 0/1 (6Gb/sec)
I-SATA 2-5 (Intel PCH) SATA 2.0 Ports 2~5 (3Gb/sec)
L-SAS 0-7 SAS Ports 0-7 (supported by LSI 2308 SAS controller)
(PCH) Slot 5 PCI-Express 2.0 x4 in x8 Slot
(CPU) Slot 6 PCI-Express 3.0 x8 in x16 Slot
SPKR1 Internal Speaker/Buzzer
SW1 UID (Unit Identifi er) Switch
6-SGPIO 1/2 Serial Link General Purpose I/O Headers for SAS Ports
T-SGPIO 1/2 Serial Link General Purpose I/O Headers for SATA Ports
USB 2/3 , 4/5 Backpan el USB 2 .0 Por ts 2 /3, 4/ 5
USB 0,1 (3.0) USB 3. 0 Por ts 0, 1 (US B 0: Type A Con necto r)
USB 8/ 9 Front Panel Ac ces sible U SB 2.0 H eader s 8/9
VGA Backpanel VGA Port

LED Description Color/State

LE3 Standby Power LED On: Power On
LE4 UID LED Blue (On): Unit Identifi ed
LE5 BMC Heartbeat LED Green (Blinking): BMC Normal

LE6 Power Status LED

LEDS2 SAS LED

Red: PWR Fail/Yellow: Standby PWR Active
Green: PWR On Normal

Green (Blinking): SAS Active/Red (Solid On): SAS
Error

5-11

SUPERSERVER 1018D-73MTF User's Manual

5-8 Connector Defi nitions

Power Connectors

The 24-pin main power connector
(JPW1) is used to provide power to
the motherboard. The 8 -pin CPU PWR
connector (JPW2) is also required for
the pro cess or. These power c onnect ors
meet the SSI EPS 12V specifi cation . See
the tab l e s on the ri g ht f o r p i n d e fi nitions.

ATX Power 24-pin Connector

Pin Defi nitions (JPW1)

Pin# Defi nition Pin # Defi nition
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 COM 3 COM
16 PS_ON 4 +5V
17 COM 5 COM
18 COM 6 +5V
19 COM 7 COM
20 Res (NC) 8 PWR_OK
21 +5V 9 5VSB
22 +5V 10 +12V
23 +5V 11 +12V
24 COM 12 +3.3V

Processor Power

Pin Defi nitions (JPW2/JPW3)

Pins Defi nition
1 through 4 Ground
5 through 8 +12V

NMI Button

The non-maskable interrupt button
header is located on pins 19 and 20
of JF1. Refer to the table on the right
for pin defi nitions.

Power LED

The Power LED connection is located on
pins 15 and 16 of JF1. Refer to the table
on the right for pin defi nitions.

HDD LED

The HDD LED connections are located on
pins 13 and 14 of JF1. Attach a cable here
to indicate HDD activity. See the table on
the right for pin defi nitions.

NMI Button

Pin Defi nitions (JF1)

Pin# Defi nition
19 Control
20 Ground

Power LED

Pin Defi nitions (JF1)

Pin# Defi nition
15 +3.3V
16 Power LED

HDD LED

Pin Defi nitions (JF1)

Pin# Defi nition
13 3.3V SB/UID Switch
14 HD Active

5-12

Chapter 5: Advanced Motherboard Setup

NIC1/NIC2 (LAN1/LAN2)

The NIC (Network Interface Controller)
LED connection for LAN port 1 is located
on pins 11 and 12 of JF1, and the LED
connection for LAN Port 2 is on pins 9
and 10. Attach NIC LED cables to NIC1
LED and NIC2 LED to display network
activities for LAN 1 and LAN2. Refer to
the table on the right for pin defi nitions.

Overheat (OH)/Fan Fail/Front UID
LED

Connect an LED cable to pins 7 and 8
of JF1 to provid e warnings of over heat,
fan failure or power failure. TRefer to the
table o n the ri ght for p in defi nitions.

GLAN1/2 LED

Pin Defi nitions (JF1)

Pin# Defi nition
9 Vcc
10 NIC 2 Link/Acitivty

11 Vcc
12 NIC 1 Link/Acitivty

OH/Fan Fail/ PWR Fail/Blue_UID

Pin# Defi nition
7 Vcc
8 Red_LED-Cathode/OH/Fan Fail/

Power Fail

LED

LED

LED Pin Defi nitions (JF1)

OH/Fan Fail/PWR Fail

LED Status (Red LED)

State Defi nition
Off Normal
On Overheat
Flashing

1 Hz
Flashing

1/4 Hz

Fan Fail

Redundant
Power
Supply Fail

Reset Button

The Reset Button connection is located
on pins 3 and 4 of JF1. Attach it to a the
hardware Reset Button on the computer
case. Refer to the table on the right for
pin defi nitions.

Power Fail LED

The Power Fail LED connection is located
on pins 5 and 6 of JF1. Refer to the table
on the right for pin defi nitions.

5-13

Reset Button

Pin Defi nitions (JF1)

Pin# Defi nition
3 Reset
4 Ground

PWR Fail LED

Pin Defi nitions (JF1)

Pin# Defi nition
5 3.3V
6 PWR LED Status

SUPERSERVER 1018D-73MTF User's Manual

Power Button

The Power Button connection is located
on pins 1 and 2 of JF1. Momentarily
contacting both pins will power on/off the
system. This button can also be confi g-
ured to function as a suspend button (see
BIOS Setup). To turn off the power in the
suspend mode, press the button for at
least 4 seconds. Refer to the table on the
right for pin defi nitions.

Universal Serial Bus (USB)

Power Button

Pin Defi nitions (JF1)

Pin# Defi nition
1 Signal
2 Ground

Back Panel USB (2.0) #2/3, 4/5

Pin Defi nitions

Pin# Defi nition Pin# Defi nition
1 +5V 5 +5V
2 USB_PN1 6 USB_PN0
3 USB_PP1 7 USB_PP0
4 Ground 8 Ground

Four Universal Serial Bus 2.0 ports (2/3,
4/5) are located on the I/O backpanel.
In addition, one USB 2.0 header (two
USB 2.0 connections: 8/9), and two USB

3.0 connectors (USB 0, USB 1) are also
provided on the motherboard for USB 3.0
support (USB cables not included). USB
0 is a Type A connector. See the tables
on the right for pin defi nitions.

Serial Ports

The COM1 port is located on the I/O
backpanel. COM2 is a header located
on the the motherboard. See the table
on the r ight for p in defi nitions.

Front Panel USB (2.0) #8/9

Pin Defi nitions

Pin # Defi nition Pin # Defi nition
1 +5V 2 +5V
3 USB_PN2 4 USB_PN3
5 USB_PP2 6 USB_PP3
7 Ground 8 Ground
9 Key 10 Ground

USB (3.0) USB #0, USB#1

Pin Defi nitions

Pin# Defi nition Pin# Defi nition
1 VBUS 6 SSTX+
2 SSRX- 7 GND_DRAIN
3 SSRX+ 8 D­4 Ground 9 D*
5 SSTX- 10

Serial Port Pin Defi nitions

(COM1/COM2)

Pin # Defi nition Pin # Defi nition
1 CDC 6 DSR
2 RXD 7 RTS
3 TXD 8 CTS
4 DTR 9 RI
5 Ground 10 NC

5-14

Fan Headers

The X10SL7-F has fi ve fan headers (Fan1

- Fan4 and FanA). These are all 4-pin fan
headers, however pins 1-3 are backward
compatible with traditional 3-pin fans. Fan
speed is controlled via IPMI based on the
system temperature. Refer to the table on
the right for pin defi nitions.

Note: Please use all 3-pin fans or all 4-pin
fans. Do not mix 3-pin fans and 4-pin fans
on the same board.

Chapter 5: Advanced Motherboard Setup

Fan Header

Pin Defi nitions

Pin# Defi nition
1 Ground (Black)
2 2.5A/+12V (Red)
3 Tachometer
4 PWM_Control

Chassis Intrusion

A Chassis Intrusion header is located at
JL1 on the motherboard. Attach the ap­propriate cable from the chassis to inform
you of a chassis intrusion when the chas­sis is opened.

Trusted Platform Module Header

This header is used to connect a Trusted
Platform Module (TPM), available sepa­rately from a third-party vendor. A TPM is
a security device that allows encryption
and authentication of hard drives, disal­lowing access if the TPM associated with
it is not installed in the system. See the
table on the right for pin defi nitions.

Chassis Intrusion

Pin Defi nitions

Pin# Defi nition
1 Intrusion Input
2 Ground

Trusted Platform Module Header

Pin Defi nitions

Pin # Defi nition Pin # Defi nition
1 LCLK 2 GND
3 LFRAME 4 No Pin
5 LRESET 6 VCC5
7 LAD3 8 LAD2
9 VCC3 10 LAD1
11 LAD0 12 GND
13 RSV0 14 RSV1
15 SB3V 16 SERIRQ
17 GND 18 CLKRUN
19 LPCPD 20 RSV2

5-15

SUPERSERVER 1018D-73MTF User's Manual

DOM PWR Connector

The Disk-On-Module (DOM) power con­nector (JSD1) provides 5V power to a
solid state DOM storage device con­nected to one of the SATA ports. See the
table on the right for pin defi nitions.

Standby Power

The Standby Power header is located
at JSTBY1 on the motherboard. See the
table at right for pin defi nitions.

Power SMB (I2C) Connector

Power System Management Bus (I
Connector (JPI

2

C1) monitors power sup-

2

C)

ply, fan and system temperatures. See
the table on the right for pin defi nitions.

DOM PWR

Pin Defi nitions

Pin# Defi nition
15V
2 Ground

3 Ground

Standby Power

Pin Defi nitions

Pin# Defi nition
1 +5V Standby
2 Ground
3 No Connection

PWR SMB

Pin Defi nitions

Pin# Defi nition
1 Clock
2 Data

3 PWR Fail
4 Ground
5 +3.3V

T-SGPIO 1/2 & 6-SGPIO 1/2 Headers

Four Serial-Link General Purpose Input/
Output headers (T-SGPIO 1/2 & 6-SGPIO
1/2) are located on the motherboard.
T-SGPIO 1/2 support the onboard SATA
interface and 6-SGPIO 1/2 support the
onboard SAS connections. See the table
on the right for pin defi nitions.

5-16

T-SGPIO/6-SGPIO

Pin Defi nitions

Pin# Defi nition Pin Defi nition
2NC 1NC
4 Data 3 Ground

6 Ground 5 Load
8 NC 7 Clock

Note: NC = No Connection.

Chapter 5: Advanced Motherboard Setup

LAN Ports

Pin Defi nition

Ethernet Ports

Two Gigabit Ethernet ports (LAN1/2)
are located on the I/O backplane on the
motherboard to provide internet con­nections. In addition, a dedicated IPMI
LAN port is included located above the
USB ports on the backplane to provide
KVM support for IPMI 2.0. All these
ports accept RJ45 type cables.

Unit Identifi er Switch/UID LED
Indicator

Pin# Defi nition
1 P2V5SB 10 SGND
2 TD0+ 11 Act LED
3 TD0- 12 P3V3SB
4 TD1+ 13 Link 100 LED (Yel-

low, +3V3SB)

5 TD1- 14 Link 1000 LED (Yel-

low, +3V3SB)
6 TD2+ 15 Ground
7 TD2- 16 Ground
8 TD3+ 17 Ground
9 TD3- 18 Ground

(NC: No Connection)

A Unit Identifi er (UID) switch and an
LED indicator are located on the moth­erboard. The UID switch is located next
to the VGA port on the backplane. The
UID LED (LE4) is located next to the
UID switch. When you press the UID
switch, the UID LED will turn on. Press
the UID switch again to turn off the LED
indicator. The UID Indicator provides
easy identifi cation of a system unit that
may be in need of service.

Note: UID can also be triggered via
IPMI on the motherboard. For more
information on IPMI, please refer to
the IPMI User's Guide posted on our
website @http://www.supermicro.com.

UID Switch

Pin# Defi nition
1 Ground
2 Ground
3 Button In
4 Ground

UID LED

Status

Color/State Status
Blue: On Unit Identifi ed

5-17

SUPERSERVER 1018D-73MTF User's Manual

Onboard Power LED (JLED1)

An onboard Power LED header is lo­cated at JLED1. This Power LED header
conne cts to JF1 to indicate t he status of
system power. See the table on the right
for pin de fi nitions.

Internal Buzzer (SP1)

The Internal Buzzer (SPKR1) can be
used to provide audible indications for
various beep codes. See the table on the
right for pin defi nitions.

Onboard PWR LED

Pin Defi nitions

Pin# Defi nition
1 Vcc
2 No Connection

3 Connection to PWR

LED in JF1

Internal Buzzer

Pin Defi nition

Pin# Defi nitions
Pin 1 Pos. (+) Beep In
Pin 2 Neg. (-) Alarm

Speaker

5-18

5-9 Jumper Settings

Explanation of Jumpers

To modify the operation of the mother­board, jumpers can be used to choose
between optional settings. Jumpers cre­ate shorts between two pins to change
the function of the connector. Pin 1 is
identifi ed with a square solder pad on the
printed circuit board. See the diagram at
right for an example of jumping pins 1 and

2. Refer to the motherboard layout page
for jumper locations.

Note: On t wo- pin jumper s, "Close d" means
the jumper is on and "Open" means the

Chapter 5: Advanced Motherboard Setup

Connector

Pins

Jumper

Setting

3 2 1

3 2 1

jumper i s off t he pins.

CMOS Clear

JBT1 is used to clear CMOS and will also clear any passwords. Instead of pins,
this jumper consists of contact pads to prevent accidentally clearing the contents
of CMOS.

To Clear CMOS

1. First power down the system and unplug the power cord(s).

2. With the power disconnected, short the CMOS pads with a metal object such
as a small screwdriver.

3. Remove the screwdriver (or shorting device).

4. Reconnect the power cord(s) and power on the system.

Note: Do not use the PW_ON connector to clear CMOS.

VGA Enable/Disable

JPG1 allows you to enable or disable the
VGA port. The default position is on pins
1 and 2 to enable VGA. See the table on
the right for jumper settings.

5-19

VGA Enable/Disable

Jumper Settings

Setting Defi nition
Pins 1-2 Enabled
Pins 2-3 Disabled

SUPERSERVER 1018D-73MTF User's Manual

PCI-E Slot SMB Enable (I2C1/I2C2)

Use Jumpers I
SMB (System Management Bus) support
to improve system management for the
PCI-E slots. See the table on the right for
jumper settings.

2

C1/I2C2 to enable PCI-E

PCI-E Slot_SMB Enable

Jumper Settings

Jumper Setting Defi nition
Pins 1-2 Enabled
Pins 2-3 Disabled

LAN Port Enable/Disable

Use JPL1/ JPL2 to enable or disable LAN
Port s 1 and 2 on the mo therbo ard. See
the table on the right for jumper settings.
The defau lt set ting is e nable d.

Backpanel USB Wake Up Enable

Close pins 1/2 of jumper JPUSB1 to
"wake up" the system when a device
installed in USB 4 or USB 5 receives an
incoming signal. See the table on the right
for jumper settings.

LAN Port En/Disable

Jumper Settings

Setting Defi nition
Pins 1-2 Enabled
Pins 2-3 Disabled

Backpanel USB Wake Up

Jumper Settings

Jumper Setting Defi nition
Pins 1-2 Enabled (Default)
Pins 2-3 Disabled

Watch Dog Enable

Watch Dog is a sy stem moni tor that c an
reboot the system when a software appli­cation hangs. Close pins 1-2 of JWD1 to
reset th e system i f an ap pli c ati on ha ngs .
Close p ins 2-3 to ge nerate a non -mask­able interrupt signal for the application
that hang s. S ee t he t a bl e on t he r i g ht fo r
jumper settings. Watch Dog must also be
enabled in the BIOS.

5-20

Watch Dog

Jumper Settings

Setting Defi nition
Pins 1-2 Reset (default)
Pins 2-3 NMI
Open Disabled

ME Recovery

Set Jumper JPME1 to select ME Firm­ware Recovery mode, which will limit
system resource for essential function
use only without putting restrictions on
power use. In the single operation mode,
online upgrade will be available via Re­covery mode. See the table on the right
for jumper settings.

SAS Enable

Jumper JPS1 allows the user to enable
the onboard SAS connectors (L-SAS
Ports 0-7). The default setting is 1-2 to
enable the connection. See the table on
the right for jumper settings.

Chapter 5: Advanced Motherboard Setup

ME Recovery

Jumper Settings

Jumper Setting Defi nition
Pins 1-2 Normal (Default)
Pins 2-3 ME Recovery

SAS Enable

Jumper Settings

Jumper Setting Defi nition
Pins 1-2 Enabled (Default)
Pins 2-3 Disabled

Manufacturer Mode Select

Close this jumper (JPME2) to bypass SPI
fl ash security and force the system to use
the Manufacturer mode which will allow
the user to fl ash the system fi rmware
from a host server to modify system
settings. See the table on the right for
jumper settings.

ME Mode Select

Jumper Settings

Jumper Setting Defi nition
Pins 1-2 Normal (Default)
Pins 2-3 Manufacture Mode

5-21

SUPERSERVER 1018D-73MTF User's Manual

5-10 Onboard Indicators

LAN1/LAN2 LEDs

The Ethernet ports (located beside the
VGA port) have two LEDs. On each Giga­bit LAN port, the yellow LED indicates
activity when blinking while the other LED
may be green, amber or off to indicate the
speed of the connection. See the table on
the right for the functions associated with
the connection speed LED.

IPMI Dedicated LAN LEDs

In addition to the Gigabit Ethernet ports,
an IPMI Dedicated LAN is also located
above the rear USB ports 2/3 on the
X10SL7-F. The yellow LED on the right
indicates activity, while the LED on the
left indicates the speed of the connec­tion by its color. See the t able at rig h t f or
more information.

Connection Speed Indication

LAN LED

LED State Defi nition
Off No connection or 10 Mb/s
Green 100 Mbps
Amber 1 Gbps

IPMI LAN Link LED &

Activity LEDs

LED State Defi nition
Off No connection or 10 Mb/s
Green 100 Mbps
Amber 1 Gbps

Onboard Power LED

An Onboard Power LED is located at LE3.
When this LED is on it means AC power
is being supplied. Be sure to turn off the
system and unplug the power cord before
removing or installing components. See
the table at right for more information.

BMC Heartbeat LED

A BMC Heartbeat LED is designated
LE5. When LED1 is blinking, BMC func­tions n ormall y. See the table at r ight fo r
more information.

5-22

Onboard PWR LED Indicator

Status Defi nition
Off System Off
On System on, or

LED State Defi nition
Green:

Blinking

LED Status

System off and PWR
Cable Connected

BMC Heartbeat LED

Status

BMC: Normal

Power Status LED

A Power Status LED is located at LE6 on
the motherboard. When the LED indica­tor turns to color red, power supply has a
probl em. See th e table at r ight fo r more
information.

Chapter 5: Advanced Motherboard Setup

Power Status LED (LE6)

Color Defi nition
Green System Power On

Yel­low

Red System Power has

(Power Normal)
Standby Power Active

(System Off)

a problem (Power
Failure)

SAS Heartbeat LED

A SAS Heartbeat LED is located at
LEDS2 on the motherboard. See the
table at r ight for m ore info rmati on.

5-11 SAS/SATA Ports

SATA/SAS Ports

Two SATA 3.0 ports (I-SATA 0/1) and four
SATA 2.0 (I-SATA 2-5) ports are located
on the board. These SATA ports are
supported by the Intel C222 PCH chip.
In addition to SATA connections, eight
SAS ports (L-SAS 0-7), supported the
LSI 2308 SAS controller, are also located
on the motherboard. See the table on the
right for pin defi nitions.

SAS Heartbeat LED Status

Color/State Defi nition
Green:

Blinking
Red: Solid On SAS Error

SAS/SATA Port Pin Defi nitions

Pin # Defi nition
1 Ground
2 TXP
3 TXN
4 Ground
5 RXN
6 RXP
7 Ground

(LEDS2)

SAS Active

5-23

SUPERSERVER 1018D-73MTF User's Manual

5-12 Installing Software

The Supermicro ftp site contains drivers and utilities for your system at ftp://ftp.

supermicro.com. Some of these must be installed, such as the chipset driver.

After accessing the ftp site, go into the CDR_Images directory and locate the ISO
fi le for your motherboard. Download this fi le to create a CD/DVD of the drivers and
utilities it contains. (You may also use a utility to extract the ISO fi le if preferred.)

Another option is to go to the Supermicro Website at

products/. Find the product page for your motherboard here, where you may down-

load individual drivers and utilities.
After creating a CD/DVD with the ISO fi les, insert the disk into the CD/DVD drive

on your system and the display shown in Figure 5-6 should appear.

Figure 5-6. Driver Installation Display Screen

http://www.supermicro.com/

Note: Click the icons showing a hand writing on paper to view the readme fi les
for each item. Click the computer icons to the right of these items to install each
item (from top to the bottom) one at a time. After installing each item, you must
re-boot the system before moving on to the next item on the list. The bottom
icon with a CD on it allows you to view the entire contents.

5-24

Chapter 5: Advanced Motherboard Setup

SuperDoctor III

The SuperDoctor® III program is a web-based management tool that supports
remote management capability. It includes Remote and Local Management tools.
The local management is called SD III Client. The SuperDoctor III program allows
you to monitor the environment and operations of your system. SuperDoctor III
displays crucial system information such as CPU temperature, system voltages
and fan status. See the fi gures below for examples of the SuperDoctor III interface.

Note: The default User Name and Password for SuperDoctor III is ADMIN / ADMIN.
Note: When SuperDoctor III is fi rst installed, it adopts the temperature threshold

settings that have been set in BIOS. Any subsequent changes to these thresholds
must be made within SuperDoctor III, as the SuperDoctor III settings override the
BIOS settings. To set the BIOS temperature threshold settings again, you would
fi rst need to uninstall SuperDoctor III.

Figure 5-7. SuperDoctor III Interface Display Screen (Health Information)

5-25

SUPERSERVER 1018D-73MTF User's Manual

Figure 5-8. SuperDoctor III Interface Display Screen (Remote Control)

Note: The SuperDoctor III program and User ’s Manual can be downloaded from

the Supermicro web site at http://www.supermicro.com/products/accessories/soft-

ware/SuperDoctorIII.cfm

II application instead.

. For Linux, we recommend that you use the SuperDoctor

5-13 Onboard Battery

Please handle used batteries carefully. Do not damage the battery in any way; a
damaged battery may release hazardous materials into the environment. Do not
discard a used battery in the garbage or a public landfi ll. Please comply with the
regulations set up by your local hazardous waste management agency to dispose
of your used battery properly.

Figure 5-9. Installing the Onboard Battery

5-26

Chapter 6: Advanced Chassis Setup

Chapter 6

Advanced Chassis Setup

This chapter covers the steps required to install components and perform main­tenance on the SC113MTQ-330CB chassis. For component installation, follow the
steps in the order given to eliminate the most common problems encountered. If
some steps are unnecessary, skip ahead to the next step.

Tools Required:

maintenance is a Philips screwdriver.

The only tool you will need to install components and perform

6-1 Static-Sensitive Devices

Electrostatic discharge (ESD) can damage electronic com ponents. To prevent
damage to any printed circuit boards (PCBs), it is important to handle them very
carefully.

The following measures are generally suffi cient to protect your equipment from
ESD damage.

Precautions

• Use a grounded wrist strap designed to prevent static discharge.

• Touch a grounded metal object before removing any board from its antistatic

bag.

• Handle a board by its edges only; do not touch its components, peripheral chips,

memory modules or gold contacts.

• When handling chips or modules, avoid touching their pins.

• Put the motherboard, add-on cards and peripherals back into their antistatic

bags when not in use.

• For grounding purposes, make sure your computer chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and
the motherboard.

6-1

SUPERSERVER 1018D-73MTF User's Manual

Figure 6-1. Chassis: Front and Rear Views

SATA Drive Bays (8)

Control Panel

Power Supply

COM Port

USB Ports LAN Ports

VGA PortDedicated IPMI LAN Port

PCI Slot

6-2 Control Panel

The control panel (located on the front of the chassis) must be connected to the
JF1 connector on the motherboard to provide you with system status indications. A
ribbon cable has bundled these wires together to simplify the connection. Connect
the cable from JF1 on the motherboard to the appropriate header on the Control
Panel PCB (printed circuit board). Make sure the red wire plugs into pin 1 on both
connectors. Pull all excess cabling out of the airfl ow path.

The control panel LEDs inform you of system status. See "Chapter 3: System In­terface" for details on the LEDs and the control panel buttons. Details on JF1 can
be found in "Chapter 5: Advanced Motherboard Installation."

6-3 System Cooling

Four 4-cm fans provide the cooling for the system. The SC1 13MTQ chassis provides
two additional open fan housings, where additional system fans may be added for
optimal cooling.

It is very important that the chassis top cover is properly installed and making a
good seal in order for the cooling air to circulate properly through the chassis and
cool the components. See Figure 6-2.

6-2

Chapter 6: Advanced Chassis Setup

Adding a System Fan

1. Turn off the power to the system and unplug the power cord.

2. Remove the chassis cover then remove the dummy fan from the fan tray.

3. Place the new fan into the vacant space in the housing while making sure the
arrows on the top of the fan (indicating air direction) point in the same direc­tion as the arrows on the other fans.

4. Connect the fan wires to the fan header on the motherboard.

5. Power up the system and check that the fan is working properly before re­placing the chassis cover.

System Fan Failure

Fan speed is controlled via IPMI. If a fan fails, the remaining fans will ramp up to
full speed. Replace any failed fan at your earliest convenience with the same type
and model (the system can continue to run with a failed fan).

The SC113MTQ chassis includes four pre-installed fans. Two additional open slots
are available so that up more fans may be added.

Replacing a System Fan (Figure 6-2)

1. Open the chassis while the system is running to determine which fan has
failed. Never run the server for an extended period of time with the chassis
open.

2. Turn off the power to the system and unplug the power cord from the power
supply.

3. Remove the failed fan's wiring from the fan header on the motherboard.

4. Lift the failed fan from the chassis and pull it completely out.

5. Place the new fan into the vacant space in the housing while making sure the
arrows on the top of the fan (indicating air direction) point in the same direc­tion as the arrows on the other fans.

6. Reconnect the fan wires to the same chassis fan header as the previous fan.

7. Power up the system and check that the fan is working properly before re­placing the chassis cover.

6-3

SUPERSERVER 1018D-73MTF User's Manual

Figure 6-2: Replacing a System Fan
(shown with optional fan housings)

6-4 Drive Bay Installation/Removal

Accessing the Drive Bays

Hard Drives: Because of their hotswap capability, you do not need to access the
inside of the chassis or power down the system to install or replace hard drives.
Proceed to the next section for instructions.

DVD-ROM Drive: For installing/removing a DVD-ROM drive, you will need to gain
access to the inside of the system by removing the top cover of the chassis. Proceed
to the "DVD-ROM Drive Installation" section later in this chapter for instructions.

Note: Only a "slim" DVD-ROM drive will fi t into the 1018D-73MTF.

Hard Drive Installation

The hard drives are mounted in drive carriers to simplify their installation and
removal from the chassis. These carriers also help promote proper airfl ow for
the drive bays. For this reason, even empty carriers without drives installed must
remain in the chassis.

Installing a Hard Drive into a Drive Carrier (Figure 6-3)

1. Insert a drive into the carrier with the PCB side facing down and the connec­tor end toward the rear of the carrier.

6-4

Chapter 6: Advanced Chassis Setup

2. Align the drive in the carrier so that the screw holes of both line up. Note that
there are holes in the carrier marked “SATA” to aid in correct installation.

3. Secure the drive to the carrier with four screws as illustrated below.

4. Insert the drive carrier into its bay, keeping the carrier oriented so that the
hard drive is on the top of the carrier and the release button is on the right
side. When the carrier reaches the rear of the bay, the release handle will
retract.

5. Push the handle in until it clicks into its locked position

Warning: Except for short periods of time (swapping hard drives), do not operate the
server with the hard drives empty.

Figure 6-3: Installing a Hard Drive into a Carrier

Removing a Hard Drive (Figure 6-4)

1. To remove a carrier, push the release button located beside the drive LEDs.

2. Swing the handle fully out and use it to pull the unit straight out.

Note: Your operating system must have RAID support to enable the hot-plug ca­pability of the hard drives.

6-5

SUPERSERVER 1018D-73MTF User's Manual

Figure 6-4. Removing a Hard Drive

1

2

1

1

DVD Drive Installation

The SC113MTQ chassis may have a DVD-ROM installed (optional).

Installing or Replacing a DVD-ROM Drive (Figure 6-5)

1. Power down the system and if necessary, remove the server from the rack
and the front bezel from the chassis.

2. Remove the chassis cover.

3. Unplug the drives power and data cables from the motherboard and/or back­plane.

4. If you are adding a new drive: Remove the mini-bezel (grate) from the drive
bay The bezel can be removed by pulling out the hard drive beneath the
DVD-ROM, then pulling the mini-bezel forward.
If you are replacing a drive: Locate the locking tab at the rear (left hand side
when viewed from the front) of the DVD-ROM drive. Push the tab toward the
drive and push the drive unit out the front of the chassis.

5. Insert the new drive unit in the slot until the tab locks in place.

6. Reconnect the data and power cables.

7. Replace the chassis cover (replace the server in the rack, if necessary) and
power up the system.

6-6

Chapter 6: Advanced Chassis Setup

Figure 6-5. Installing a DVD-ROM Drive

6-7

SUPERSERVER 1018D-73MTF User's Manual

6-5 Power Supply

The SuperServer 1018D-73MTF has a single 330 watt power supply, which is auto­switching capable. This enables it to automatically sense and operate with a 100V
to 240V input voltage.

Power Supply Failure

If the power supply unit fails, the system will shut down and you will need to replace
the unit. Replacement units can be ordered directly from Supermicro (see contact
information in the Preface). As there is only one power supply unit in the chassis,
power must be completely removed from the server before removing and replacing
the power supply unit for whatever reason.

Removing/Replacing the Power Supply (Figure 6-6)

1. First power down the system and unplug the AC power cord from the power
supply.

2. Extend the chassis from the rack if necessary, then remove the top chassis
cover.

3. To remove the failed power unit, remove the two screws that secure the
power module to its housing inside the chassis. You can then pull the unit
straight out of the chassis.

4. Replace the failed unit with another unit of the same wattage. You must re­place it with the exact same power supply (same model number).

5. Carefully insert the new unit into position into the chassis and secure it with
the two screws you removed previously.

6. Reconnect the AC power cord, replace the top chassis cover and push the
unit back into the rack.

7. Finish by powering up the server with the power button on the front control
panel.

6-8

Chapter 6: Advanced Chassis Setup

Figure 6-6. Removing/Replacing the Power Supply

6-9

SUPERSERVER 1018D-73MTF User's Manual

Notes

6-10

Chapter 7: BIOS

Chapter 7

BIOS

7-1 Introduction

This chapter describes the AMI BIOS Setup Utility for the X10SL7-F. The ROM BIOS
is stored in a Flash EEPROM and can be easily updated. This chapter describes
the basic navigation of the AMI BIOS Setup Utility setup screens.

Note: For AMI BIOS Recovery, please refer to the UEFI BIOS Recovery
Instructions in Appendix C.

Starting BIOS Setup Utility

To enter the AMI BIOS Setup Utility screens, press the <Delete> key while the
system is booting up.

Note: In most cases, the <Delete> key is used to invoke the AMI BIOS
setup screen. There are a few cases when other keys are used, such as
<F1>, <F2>, etc.

Each main BIOS menu option is described in this manual. The Main BIOS setup
menu screen has two main frames. The left frame displays all the options that can
be confi gured. Grayed-out options cannot be confi gured. Options in blue can be
confi gured by the user. The right frame displays the key legend. Above the key
legend is an area reserved for a text message. When an option is selected in the
left frame, it is highlighted in white. Often a text message will accompany it. (Note:
the AMI BIOS has default text messages built in. Supermicro retains the option to
include, omit, or change any of these text messages.)

The AMI BIOS Setup Utility uses a key-based navigation system called "hot keys".
Most of the AMI BIOS setup utility "hot keys" can be used at any time during the
setup navigation process. These keys include <F1>, <F4>, <Enter>, <ESC>, arrow
keys, etc.

Note: Options printed in Bold are default settings.

How To Change the Confi guration Data

The confi guration data that determines the system parameters may be changed by
entering the AMI BIOS Setup utility. This Setup utility can be accessed by pressing
<Del> at the appropriate time during system boot.

7-1

SUPERSERVER 1018D-73MTF User's Manual

How to Start the Setup Utility

Normally, the only visible Power-On Self-Test (POST) routine is the memory test.
As the memory is being tested, press the <Delete> key to enter the main menu of
the AMI BIOS Setup Utility. From the main menu, you can access the other setup
screens. An AMI BIOS identifi cation string is displayed at the left bottom corner of
the screen, below the copyright message.

Warning! Do not upgrade the BIOS unless your system has a BIOS-related issue.
Flashing the wrong BIOS can cause irreparable damage to the system. In no event
shall Supermicro be liable for direct, indirect, special, incidental, or consequential dam­ages arising from a BIOS update. If you have to update the BIOS, do not shut down
or reset the system while the BIOS is updating. This is to avoid possible boot failure.

7-2 Main Setup

When you fi rst enter the AMI BIOS Setup utility , you will enter the Main setup screen.
You can always return to the Main setup screen by selecting the Main tab on the
top of the screen. The Main BIOS Setup screen is shown below.

7-2

Chapter 7: BIOS

The following Main menu items will display:

System Time/System Date

Use this option to change the system date and time. Highlight System Date or
System Time using the arrow keys. Enter new values through the keyboard. Press

the <Tab> key or the arrow keys to move between fi elds. The date must be entered
in Day MM/DD/YY format. The time is entered in HH:MM:SS format.

Note: The time is in the 24-hour format. For example, 5:30 P.M. appears
as 17:30:00.

The following BIOS items will also be displayed:

Supermicro X10SL7-F

Version

Build Date

Memory Information

Total Memory

This displays the total size of memory available in the system.

7-3

SUPERSERVER 1018D-73MTF User's Manual

7-3 Advanced Setup Confi gurations

Use the arrow keys to select Boot Setup and press <Enter> to access the submenu
items:

Warning: Take Caution when changing the Advanced settings. An incorrect value, a
very high DRAM frequency , or an incorrect DRAM timing setting may make the system
unstable. When this occurs, revert to the setting to its manufacture default setting.



Boot Feature

Quiet Boot

This feature selects the screen display between POST messages or the OEM
logo at bootup. Select Disabled to display the POST messages. Select Enabled
to display the OEM logo instead of the normal POST messages. The options are

Enabled and Disabled.

AddOn ROM Display Mode

This feature sets the display mode for the Option ROM. Select Keep Current to
use the current AddOn ROM display setting. Select Force BIOS to use the Option
ROM display mode set by the system BIOS. The options are Force BIOS and
Keep Current.

Bootup Num-Lock

This featu re sel ect s the Powe r-on st ate for t he Num loc k key. The options ar e Of f
and On.

7-4

Chapter 7: BIOS

Wait For 'F1' If Error

This feature force s the system to wa it until th e 'F1' key is pressed if an e rror o c­curs. T he opti ons are D isab led and Enabl ed.

Interrupt 19 Capture

Interrupt 19 is the software interrupt that handles the boot disk function. When this
item is set to Enabled, the ROM BIOS of the host adaptors will "capture" Interrupt 19
at bootup and allow the drives that are attached to these host adaptors to function
as bootable disks. If this item is set to Disabled, the ROM BIOS of the host adap­tors will not capture Interrupt 19, and the drives attached to these adaptors will not
function as bootable devices. The options are Enabled and Disabled.

Re-try Boot

If this item is enabled, the BIOS will automatically reboot the system from a speci­fi ed boot device after its initial boot failure. The options are Disabled, Legacy
Boot, and EFI B oot.



Power Confi guration

Watch Dog Function

If enable d, the Watch Dog Timer will a l l o w the system to reb oot when it is in a ctive
for more t han 5 minu tes. The o ption s are Enabl ed and Disabled.

Power Button Function

This feature controls how the system shuts down when the power button is pressed.
Select 4_Seconds_Override for the user to power off the system after pressing and
holding the power button for 4 seconds or longer. Select Instant Off to instantly
power off the system as soon as the user presses the power button. The options
are 4 Seconds Override and Instant Off.

Restore on AC Power Loss

Use this feature to set the power state after a power outage. Select Power-Off for
the system power to remain off after a power loss. Select Power-On for the system
power to be turned on after a power loss. Select Last State to allow the system
to resume its last power state before a power loss. The options are Power-On,
Stay-Off and Last State.

7-5

SUPERSERVER 1018D-73MTF User's Manual



CPU Confi guration

The following CPU information will be displayed:

• Type of CPU

• CPU Signature

• Microcode Patch

• Max (Maximum) CPU Speed

• Min (Minimum) CPU Speed

• CPU Speed

• Processor Cores

• Intel HT(Hyper-Threading) Technology

• Intel VT-x (Virtualization) Technology

• Intel SMX (Trusted Execution) Technology

• 64-bit

• EIST Technology

• CPU C3 State

• CPU C6 State

• CPU C7 State

• L1 Data Cache

• L1 Code Cache

• L2 Cache

• L3 Cache

7-6

Chapter 7: BIOS

Hyper-threading

Select Enabled to support Intel Hyper-threading Technology to enhance CPU per­formance. The options are Enabled and Disabled.

Active Processor Cores

This feature determines how many CPU cores will be activated for each CPU. When
all is selected, all cores in the CPU will be activated. (Please refer to Intel's web
site for more information.) The options are All, 1, 2, and 3.

Limit CPUID Maximum

Select Enabled to set the maximum CPU ID value and to boot the legacy operat­ing systems that cannot support processors with extended CPUID functions. The
options are Enabled and Disabled (for the Windows OS).

Execute Disable Bit Capability (Available if supported by the OS & the CPU)

Set to Enabled to enable the Execute Disable Bit which will allow the processor
to designate areas in the system memory where an application code can execute
and where it cannot, thus preventing a worm or a virus from fl ooding illegal codes
to overwhelm the processor or damage the system during an attack. The default is

Enabled. (Refer to Intel and Microsoft Web Sites for more information.)

Intel® Virtualization Technology (Available when supported by the CPU)

Selec t Enabl ed to us e the I ntel Vi r tua liz atio n Technolog y to allo w one p lat for m to
run mult iple ope rating syst ems and app licati ons in inde pendent p art itions , creat­ing mult iple " vi r tu al" sy stems i n one p hysic al c o mput er. The opti ons ar e Enabled
and Disabled.

Hardware Prefetcher (Available when supported by the CPU)

If set to Enabled, the hardware prefetcher will prefetch streams of data and instruc­tions from the main memory to the L2 cache to improve CPU performance. The
options are Disabled and Enabled.

Adjacent Cache Line Prefetch (Available when supported by the CPU)

Select Enabled for the CPU to prefetch both cache lines for 128 bytes as comprised.
Select Disabled for the CPU to prefetch both cache lines for 64 bytes. The options
are Disabled and Enabled.

Note: If there is any c hange to this s etting, you wi ll need to rebo ot the
system for t he change to t ake effec t. Please r efer to Intel’s web site fo r
detailed information.

7-7

SUPERSERVER 1018D-73MTF User's Manual

CPU AES

Select Enable to enable Intel CPU Advanced Encryption Standard (AES) Instruc­tions for CPU to enhance data integrity. The options are Enabled and Disabled.

EIST

EIST (Enhanced Intel SpeedStep Technology) allows the system to automatically
adjust processor voltage and core frequency in an effort to reduce power consump­tion and heat dissipation. Please refer to Intel’s web site for detailed information.
The options are Disabled and Enabled.

Turbo Mode

This feature allows processor cores to run faster than the frequency recommended
by the manufacturer. The options are Disabled and Enabled. If this feature is set
to Enabled, the following items will display:

CPU Power Limit1 (Available when "Turbo Mode" is set to Enabled)

Use this feature to set the power limit for CPU1. Use the number keys on your
keyboard to enter the value. Enter 0 to use the manufacture default setting.

CPU Power Limit1 Time (Available when "Turbo Mode" is set to Enabled)

This item allows the user to determine how long CPU1 should operate at the
power limit set by the user for the item above. Use the number keys on your
keyboard to enter the value. Enter 0 to use the manufacture default setting.

CPU Power Limit2 (Available when "Turbo Mode" is set to Enabled)

Use this feature to set the power limit for CPU2. Use the number keys on your
keyboard to enter the value. Enter 0 to use the manufacture default setting.

DDR Power Limit1 (Available when "Turbo Mode" is set to Enabled)

Use this feature to set the power limit for DDR1. Use the number keys on your
keyboard to enter the value. Enter 0 to use the manufacture default setting.

DDR Power Limit1 Time (Available when "Turbo Mode" is set to Enabled)

This item allows the user to determine how long DDR1 should operate at the
power limit set by the item above. Use the number keys on your keyboard to
enter the value. Enter 0 to use the manufacture default setting.

DDR Power Limit2 (Available when "Turbo Mode" is set to Enabled)

Use this feature to set the power limit for DDR2. Use the number keys on your
keyboard to enter the value. Enter 0 to use the manufacture default setting.

7-8

Chapter 7: BIOS

1-Core Ratio Limit (Available when "Turbo Mode" is set to Enabled)

This increases (multiplies) 1 clock speed in the CPU core in relation to the bus
speed when one CPU core is active. Press "+" or "-" on your keyboard to change
the value. Enter 0 to use the manufacture default setting.

2-Core Ratio Limit (Available when "Turbo Mode" is set to Enabled)

This increases (multiplies) 2 clock speeds in the CPU core in relation to the bus
speed when two CPU cores are active. Press "+" or "-" on your keyboard to
change the value. Enter 0 to use the manufacture default setting.

3-Core Ratio Limit (Available when "Turbo Mode" is set to Enabled)

This increases (multiplies) 3 clock speeds in the CPU core in relation to the bus
speed when three CPU cores are active. Press "+" or "-" on your keyboard to
change the value. Enter 0 to use the manufacture default setting.

4-Core Ratio Limit (Available when "Turbo Mode" is set to Enabled)

This increases (multiplies) 4 clock speeds in the CPU core in relation to the bus
speed when four CPU cores are active. Press "+" or "-" on your keyboard to
change the value. Enter 0 to use the manufacture default setting.

Energy Performance

Use this feature to select an appropriate fan setting to achieve the maximum system
performance (with maximum cooling) or maximum energy effi ciency (with maximum
power saving). The fan speeds are controlled by the fi rmware management via IPMI

2.0. The options are Performance, Balanced Performance, Balanced Energy, and
Energy Effi cient.

VR Current Value

Use this feature to set the limit on the current voltage regulator (VR). Press "+" or
"-" on your keyboard to change this value. Enter 0 to use the manufacture default
setting.

CPU C-States

C-States architecture, a processor power management platform developed by
Intel, can further reduce power consumption from the basic C1 (Halt State) state
that blocks clock cycles to the CPU. Select Enabled for CPU C-Sates support. The
options are Enabled and Disabled. If this feature is set to Enabled, the following
items will display:

Enhanced C1E State (Available when "CPU C-States" is set to Enabled)

Select Enabled to enable Enhanced C1 Power State to boost system perfor­mance. The options are Enabled and Disabled.

7-9

SUPERSERVER 1018D-73MTF User's Manual

CPU C3 Report (Available when "CPU C-States" is set to Enabled)

Select Enabled to allow the BIOS to report the CPU C3 State (ACPI C2) to the
operating system. During the CPU C3 State, the CPU clock generator is turned
off. The options are Enabled and Disabled.

CPU C6 Report (Available when "CPU C-States" is set to Enabled)

Select Enabled to allow the BIOS to report the CPU C6 State (ACPI C3) to the
operating system. During the CPU C6 State, the power to all caches is turned
off. The options are Enabled and Disabled.

C6 Latency (Available when "CPU C-States" is set to Enabled)

Select Short to set a short delay time(period) during which the BIOS reports
CPU C6 State (ACPI C3) to the operating system. Select Long to set a long
delay time(period) during which the BIOS reports CPU C6 State (ACPI C3)
to the operating system. The options are Short and Long.

CPU C7 Report (Available when "CPU C-States" is set to Enabled

Select Enabled to allow the BIOS to report the CPU C7 State (ACPI C3) to the
operating system. CPU C7 State is a processor-specifi c low C-State. The options
are Disabled, CPU C7, and CPU C7s

C7 Latency (Available when "CPU C-States" is set to Enabled)

Select Short to set a short delay time(period) during which the BIOS reports
CPU C7 State (ACPI C3) to the operating system. Select Long to set a long
delay time(period) during which the BIOS reports CPU C7 State (ACPI C3)
to the operating system. The options are Short and Long.

C1 State Auto Demotion

When this item is enabled, the CPU will conditionally demote C3, C6 or C7
requests to C1 State based on un-cored auto-demote information. The options
are Disabled and Enabled.

C3 State Auto Demotion

When this item is enabled, the CPU will conditionally demote C6 or C7 requests
to C3 State based on un-cored auto-demote information. The options are Dis­abled and Enabled.

C-State Pre-Wake

Select Enabled to support C State Pre-Wake State features. The options are
Enabled and Disabled

7-10

Chapter 7: BIOS

Package C-State limit

Select Auto for the AMI BIOS to automatically set the limit on the C-State package
register. The options are C0/C1, C2, C3, C6, C7 and Auto.



Chipset Confi guration

Warning! Setting the wrong values in the following sections may cause the system

to malfunction.



System Agent (SA) Confi guration

The following System Agent (SA) information will be displayed:

• System Agent Bridge Name

• VT-d Capability

VT-d

Select Enabled to enable Intel Virtualization Technology support for Direct I/O VT-d
by reporting the I/O device assignments to VMM through the DMAR ACPI Tables.
This feature offers fully-protected I/O resource-sharing across the Intel platforms,
providing the user with greater reliability, security and availability in networking and
data-sharing. The settings are Enabled and Disabled.



Graphics Confi guration

This item displays the following graphics information:

• IGFX VBIOS Version

• IGfx Frequency

Primary Display

Use this feature to select the graphics device to be used as the primary display.
You can select from a IGFX, a PGE or a PCIE device. The options are Auto, PEG,
and PCIE.

Primary PEG (PCI-Express Graphics)

This feature allows the user to specify which graphics card to be used as the
primary graphics card. The options are Auto, PEG11 and PEG12.

7-11

SUPERSERVER 1018D-73MTF User's Manual

Primary PCIE (PCI-Express Device)

This feature allows the user to specify which graphics card to be used as the
primary graphics card. The options are PCIE1, PCIE2, PCIE3, PCIE4, PCIE5 ,
PCIE6, PCIE7 and Auto.



PCI-E Confi guration

This item displays the information of the (graphics) device installed on a PCI-E
slot.

Riser Card on CPU Slot 6

PEG0 Gen X/PEG1 Gen X/PEG2 Gen X

This feature allows the user to select PCI-E support for the device installed on
SLOT6. The options are Auto, Gen1 (Generation 1), Gen 2 and Gen 3.

Detect Non-Compliance Device

Select Enabled for the AMI BIOS to automatically detect a PCI-E device that is
not compliant with the PCI-E standards. The options are Enabled and Disabled.

Program PCI-E ASPM After OpROM

PCI-E ASPM, the Active State Power Management for PCI-Express slots, is a
power management protocol used to manage power consumption of serial-link
devices installed on PCI-Exp slots during a prolonged off-peak time. If this item
is set to Enabled, PCI-E ASMP will be programmed after OpROM. If this item
is set to Disabled, the PCI-E ASPM will be programmed before OpROM. The
options are Enabled and Disabled.

PEG0-ASPM/PEG1-ASPM/PEG2-ASPM/

Use this feature to set the ASPM (Active State Power Management) level for the
graphics device installed on a PCI-E slot specifi ed by the user. The options are
Disabled, Auto, ASPM L0s, ASPM L1, and, ASPM L0sL1.

PCI-E SLOT 0 ASPM ~ PCI-E SLOT 7 ASPM

This feature confi gures the ASPM (Active State Power Management) settings for
the graphics devices installed on PCI-E SLOT 0 to PCI-E SLOT 7. The options
are Disabled, L0s, L1, L0sL1 and Auto.

7-12

Chapter 7: BIOS



Memory Confi guration

This item displays the information on the memory modules installed on the
motherboard.

• Memory RC Version

• Memory Frequency

• Total Memory

• Memory Voltage

• DIMMA1

• DIMMA2

• DIMMB1

• DIMMB2

• CAS Latency (tCL)

• Minimum Delay Time

• CAS to RAS (tRODmin)

• Row Precharge (tRPmin)

• Active to Precharege (tRASmin)

Memory Frequency Limiter

This feature sets the limit of memory frequency for DIMM modules installed
on the the motherboard. The options are Auto, 1067 (MHz), 1333 (MHz), and
1600 (MHz).

Max TOLUD (Top of Low Usable DRAM)

This feature sets the maximum TOLUD value, which specifi es the "Top of Low
Usable DRAM" memory space to be used by internal graphics devices, GTT
Stolen Memory, and TSEG, respectively, if these devices are enabled. The op­tions are Enabled and Dynamic, 1 GB, 1.25 GB, 1.5 GB, 1.75 GB,. 2 GB, 2.25
GB, 2.5 GB, 2.75 GB, 3 GB and 3.25 GB.

Note: TSEG is a block of memory that is only accessible by the processor
while operating in SMM mode.

7-13

SUPERSERVER 1018D-73MTF User's Manual

Memory Scrambler

This feature enables or disables memory scrambler support for memory error
correction. The settings are Enabled and Disabled.



PCH-IO Confi guration

This item displays the information for PCH-IO Chip.

• Intel PCH Rev ID

• USB Confi guration

• USB Devices

EHCI1

Select Enabled to enable EHCI (Enhanced Host Controller Interface) Controller 1
for USB 2.0 support. One EHCI controller must always be enabled. The settings
are Enabled and Disabled.

EHCI2

Select Enabled to enable EHCI (Enhanced Host Controller Interface) Controller 2
for USB 2.0 support. One EHCI controller must always be enabled. The settings
are Enabled and Disabled.

Legacy USB Support

This feature enables support for legacy USB devices. Select Auto to disable
legacy support if USB devices are not present. Select Disable to have USB
devices available only for EFI applications. The options are Enabled, Disabled
and Auto.

Port 60/64 Emulation

This feature enables or disables I/O port 60h/64h emulation support. This should
be enabled for complete USB keyboard legacy support for non-USB-aware op­erating systems. The options are Disabled and Enabled.

XHCI Hand-Off

This item is a work-around solution for operating systems that do not support
XHCI (Extensible Host Controller Interface) hand-off. The XHCI ownership
change should be claimed by the XHCI driver. The settings are Enabled and
Disabled.

7-14

Chapter 7: BIOS

EHCI Hand-Off

This item is for Operating Systems that do not support Enhanced Host Controller
Interface (EHCI) hand-off. When this item is enabled, EHCI ownership change
will be claimed by the EHCI driver. The settings are Enabled and Disabled.

XHCI Mode

This feature handles the operation mode for the XHCI (Extensible Host Control­ler Interface) controller. The settings are Smart Auto, Auto, Enabled, Disabled
and Manual.



SATA Confi guration

When this submenu is selected, the AMI BIOS automatically detects the presence
of the SATA Devices and displays the following items:

SATA Controllers

This item Enables or Disables the built-in SA TA controllers on the motherboard. The
options are Enabled and Disabled.

SATA Mode Selection

This item selects the mode for the installed SATA drives. The options are IDE,

AHCI and RAID.

SATA RAID Option ROM/UEFI Driver (Available if the item above - SATA
Mode Select is set to AHCI or RAID)

Select Enabled to use the SATA RAID Option ROM/UEFI driver for system boot.
The options are Enabled and Disabled.

If the item above -SATA Mode Select is set to AHCI, the following items are
displayed:

Serial ATA Port 0~ Port 5

This item displays the information detected on the installed SATA drives on the
particular SATA port.

• Model number of drive and capacity

• Software Preserve Support

Port 0 ~ Port 5 Hot Plug

This feature designates the port specifi ed for hot plugging. Set this item to En-
abled for hot-plugging support, which will allow the user to replace a SATA disk
drive without shutting down the system. The options are Enabled and Disabled.

7-15

SUPERSERVER 1018D-73MTF User's Manual

Port 0 ~ Port 1 SATA Device Type

This feature confi gures the selected SATA port to support either a solid state
drive or hard disk drive. The options are Hard Disk Drive and Solid Sate Drive.

Port 0 ~ Port 5 Spin Up Device

On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRE­SET initialization sequence to the device. The options are Enabled and Disabled.

If the item above - SATA Mode Select is set to IDE, the following items are
displayed:

Serial ATA Port 0~ Port 5

This item displays the information detected on the installed SATA drives on the
particular SATA port.

• Model number of drive and capacity

• Software Preserve Support

If the item above - SATA Mode Select is set to RAID, the following items are
displayed:

Serial ATA Port 0~ Port 5

This item displays the information detected on the installed SATA drives on the
particular SATA port.

• Model number of drive and capacity

• Software Preserve Support

Port 0 ~ Port 5 Hot Plug

This feature designates this port for hot plugging. Set this item to Enabled for
hot-plugging support, which will allow the user to replace a SATA drive without
shutting down the system. The options are Enabled and Disabled.

Port 0 ~ Port 1 SATA Device Type

This feature confi gures the selected SATA port to support either a solid state
drive or hard disk drive. Set this item to Enabled to enable hot-plugging. The
options are Hard Disk Drive and Solid Sate Drive.

Port 0 ~ Port 5 Spin Up Device

On an edge detect from 0 to 1, set this item to allow the PCH to start a COMRE­SET initialization sequence to the device. The options are Enabled and Disabled.

7-16