Supermicro SUPERSERVER 6014L-M4 User Manual

®

SUPER

SUPERSERVER 6014L-M4

USER’S MANUAL

Revision 1.0

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates.

Please Note: For the most up-to-date version of

this manual, please see our web site at www.supermicro.com.

SUPERMICRO COMPUTER reserves the right to make changes to the product described in this
manual at any time and without notice. This product, including software, if any, and documenta­tion may not, in whole or in part, be copied, photocopied, reproduced, translated or reduced to any
medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE
OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT HAVE
LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE
PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING
OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for all
claims will not exceed the price paid for the hardware product.

Manual Revision 1.0

Release Date: February 23, 2006

Unless you request and receive written permission from SUPER MICRO COMPUTER, you may not
copy any part of this document.

Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2006 by SUPER MICRO COMPUTER INC.
All rights reserved.

Printed in the United States of America

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It

provides information for the installation and use of the SuperServer 6014L-M4. In-

stallation and maintenance should be performed by experienced technicians only.

The SuperServer 6014L-M4 is a high-end dual processor rackmount server based

on the SC813MS-300C 1U rackmount server chassis and the Super X6DLP-4G2

serverboard. The X6DLP-4G2 supports Intel

479-pin PGA sockets.

® Xeon® LV or ULV processors in

Preface

Manual Organization

Chapter 1: Introduction

The fi rst chapter provides a checklist of the main components included with the serv-

er system and describes the main features of the Super X6DLP-4G2 serverboard

and the SC813MS-300C chassis.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer 6014L-M4 into

a rack and check out the server confi guration prior to powering up the system. If

your server was ordered without the processor and memory components, this chap-

ter will refer you to the appropriate sections of the manual for their installation.

Chapter 3: System Interface

Refer to this chapter for details on the system interface, which includes the functions

and information provided by the control panel on the chassis as well as other LEDs

located throughout the system.

iii

SUPERSERVER 6014L-M4 User's Manual

Chapter 4: System Safety

You should thoroughly familiarize yourself with this chapter for a general overview

of safety precautions that should be followed when installing and servicing the

SuperServer 6014L-M4.

Chapter 5: Advanced Serverboard Setup

Chapter 5 provides detailed information on the X6DLP-4G2 serverboard, including

the locations and functions of connectors, headers and jumpers. Refer to this chap-

ter when adding or removing processors or main memory and when reconfi guring

the serverboard.

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the SC813MS-300C 1U rackmount

server chassis. You should follow the procedures given in this chapter when install-

ing, removing or reconfi guring SCSI or peripheral drives and when replacing system

power supply units and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed informa-

tion on running the CMOS Setup Utility.

Appendix A: BIOS Error Beep Codes

Appendix B: BIOS POST Checkpoint Codes

Appendix C: Software Installation

Appendix D: System Specifi cations

iv

Notes

Preface

v

SUPERSERVER 6014L-M4 User's Manual

Table of Contents

Preface

About This Manual ...................................................................................................... iii

Manual Organization ................................................................................................... iii

Chapter 1: Introduction

1-1 Overview ......................................................................................................... 1-1

1-2 Serverboard Features ..................................................................................... 1-2

1-3 Server Chassis Features ................................................................................ 1-5

1-4 Contacting Supermicro ................................................................................... 1-7

Chapter 2: Server Installation

2-1 Overview ......................................................................................................... 2-1

2-2 Unpacking the System ................................................................................... 2-1

2-3 Preparing for Setup ........................................................................................ 2-1

Choosing a Setup Location .................................................................... 2-2

Rack Precautions ..................................................................................... 2-2

Server Precautions ................................................................................... 2-2

Rack Mounting Considerations ................................................................ 2-3

2-4 Installing the System into a Rack ................................................................... 2-4

Identifying the Sections of the Rack Rails ............................................... 2-4

Installing the Rear Inner Rails ................................................................. 2-4

Installing the Rack Rails .......................................................................... 2-5

Installing the Server into the Rack ........................................................... 2-6

Installing the Server into a Telco Rack .................................................... 2-7

2-5 Checking the Serverboard Setup ................................................................... 2-8

2-6 Checking the Drive Bay Setup ..................................................................... 2-10

Chapter 3: System Interface

3-1 Overview ......................................................................................................... 3-1

3-2 Control Panel Buttons .................................................................................... 3-1

Reset ........................................................................................................ 3-1

Power ....................................................................................................... 3-1

3-3 Control Panel LEDs ........................................................................................ 3-2

Overheat/Fan Fail .................................................................................... 3-2

NIC2 ......................................................................................................... 3-2

NIC1 ......................................................................................................... 3-2

HDD .......................................................................................................... 3-2

Power ....................................................................................................... 3-3

vi

Table of Contents

3-4 SCSI Drive Carrier LEDs ................................................................................ 3-3

Chapter 4: System Safety

4-1 Electrical Safety Precautions .......................................................................... 4-1

4-2 General Safety Precautions ........................................................................... 4-2

4-3 ESD Precautions ............................................................................................ 4-3

4-4 Operating Precautions .................................................................................... 4-4

Chapter 5: Advanced Serverboard Setup

5-1 Handling the Serverboard .............................................................................. 5-1

5-2 Serverboard Installation .................................................................................. 5-2

5-3 Processor and Heatsink Installation ............................................................... 5-3

5-4 Connecting Cables ......................................................................................... 5-6

Connecting Data Cables .......................................................................... 5-6

Connecting Power Cables ....................................................................... 5-6

Connecting the Control Panel .................................................................. 5-7

5-5 I/O Ports ......................................................................................................... 5-7

5-6 Installing the Processor .................................................................................. 5-5

5-7 Installing Memory ........................................................................................... 5-8

5-8 Adding PCI Cards ........................................................................................... 5-9

5-9 Serverboard Details ...................................................................................... 5-10

X6DLP-4G2 Layout ................................................................................ 5-10

X6DLP-4G2 Quick Reference ................................................................ 5-11

5-10 Connector Defi nitions ................................................................................... 5-12

ATX Power Connector ........................................................................... 5-12

Processor Power Connector .................................................................. 5-12

NMI Button ............................................................................................. 5-12

Power LED ............................................................................................. 5-12

HDD LED ............................................................................................... 5-13

NIC1/NIC LEDs ...................................................................................... 5-13

Overheat/Fan Fail LED .......................................................................... 5-13

Power Fail LED ...................................................................................... 5-13

Reset Connector .................................................................................... 5-14

Power Button .......................................................................................... 5-14

JLAN1/2 Ethernet Ports ......................................................................... 5-14

Chassis Intrusion .................................................................................... 5-14

Universal Serial Bus ............................................................................... 5-15

Universal Serial Bus Headers ................................................................ 5-15

Fan Headers .......................................................................................... 5-15

vii

SUPERSERVER 6014L-M4 User's Manual

Speaker/Power LED/Keylock ................................................................. 5-16

Wake-On-Ring ........................................................................................ 5-16

Wake-On-LAN ........................................................................................ 5-16

Power Fault ............................................................................................ 5-17

ATX PS/2 Keyboard and PS/2 Mouse Ports ......................................... 5-17

SMB Power Connector .......................................................................... 5-17

Serial Ports ............................................................................................. 5-17

5-11 Jumper Settings ............................................................................................ 5-18

Explanation of Jumpers ......................................................................... 5-18

CMOS Clear ........................................................................................... 5-18

JLAN1/2 Enable/Disable ........................................................................ 5-18

VGA Enable/Disable ............................................................................... 5-19

SMBus to PCI Slots ............................................................................... 5-19

Power Force On ..................................................................................... 5-19

Watch Dog ............................................................................................. 5-19

Alarm Reset ........................................................................................... 5-20

SCSI Enable/Disable .............................................................................. 5-20

SCSI Termination Enable/Disable .......................................................... 5-20

5-12 Onboard Indicators ....................................................................................... 5-21

JLAN LEDs ............................................................................................. 5-21

System Status LEDs .............................................................................. 5-21

Onboard LED Indicators ........................................................................ 5-21

5-13 Parallel Port, Floppy, IDE, SATA and SCSI Drive Connections ................... 5-22

Parallel Port ............................................................................................ 5-22

Floppy Connector ................................................................................... 5-23

SATA Connectors ................................................................................... 5-23

IDE Connector ........................................................................................ 5-24

SCSI Connector ..................................................................................... 5-25

Chapter 6: Advanced Chassis Setup

6-1 Static-Sensitive Devices ................................................................................. 6-1

6-2 Control Panel .................................................................................................. 6-2

6-3 System Fans ................................................................................................... 6-3

System Fan Failure .................................................................................. 6-3

6-4 Drive Bay Installation/Removal ...................................................................... 6-3

Removing the Front Bezel ....................................................................... 6-3

Accessing the Drive Bays ........................................................................ 6-4

SCSI Drive Installation ............................................................................. 6-4

SCA Backplane ........................................................................................ 6-5

viii

Table of Contents

CD/DVD-ROM Drive Installation .............................................................. 6-6

6-5 Power Supply ................................................................................................. 6-7

Power Supply Failure ............................................................................... 6-7

Replacing the Power Supply .................................................................... 6-7

Chapter 7: BIOS

7-1 Introduction ..................................................................................................... 7-1

7-2 Main Setup ..................................................................................................... 7-2

7-3 Advanced Settings .......................................................................................... 7-3

7-4 Boot Settings ................................................................................................ 7-15

7-5 Security Settings ........................................................................................... 7-18

7-6 Exit Options .................................................................................................. 7-19

Appendices:

Appendix A: BIOS Error Beep Codes ...................................................................... A-1

Appendix B: BIOS POST Checkpoint Codes .......................................................... B-1

Appendix C: Software Installation ........................................................................... C-1

Appendix D: System Specifi cations ........................................................................ D-1

ix

SUPERSERVER 6014L-M4 User's Manual

Notes

x

Chapter 1: Introduction

Chapter 1

Introduction

1-1 Overview

The SuperServer 6014L-M4 is a high-end dual processor, 1U rackmount server

featuring state-of-the-art technology. The 6014L-M4 is comprised of two main

subsystems: the SC813MS-300C 1U rackmount chassis and the X6DLP-4G2

serverboard. Please refer to our web site for information on operating systems that

have been certifi ed for use with the 6014L-M4 (www.supermicro.com).

In addition to the serverboard and chassis, various hardware components may have

been included with the 6014L-M4, as listed below.

 Two (2) CPU heatsinks (SNK-P0019)

 One (1) slim DVD drive [DVM-PNSC-824(B)]

 SCSI Accessories:

Four (4) SCSI hard drive carriers (CSE-PT-39(B))

One (1) SCSI backplane (CSE-SATA-813S)

One (1) SCSI cables (CBL-0043)

 One (1) 3.3V 64-bit, 66 MHz PCI-X slot riser card (CSE-RR1U-X)

 Three (3) cooling fans (FAN-0061)

 Rackmount hardware with screws (CSE-PT52):

Two (2) rack rail assemblies

Six (6) brackets for mounting the rack rails in a rack/telco rack

 One (1) CD containing drivers and utilities

 SuperServer 6014L-M4 User's Manual

Note: "B" indicates part is also available in black.

1-1

S

UPERSERVER 6014L-M4 User's Manual

1-2 Serverboard Features

At the heart of the SuperServer lies the X6DLP-4G2, a dual processor serverboard

based on Intel's E7520 chipset and designed to provide maximum performance.

Below are the main features of the X6DLP-4G2.

Processors

The X6DLP-4G2 supports single or dual Intel® Xeon® LV or ULV processors in

479-pin PGA sockets. Please refer to our web site for a complete listing of sup-

ported processors (www.supermicro.com).

Memory

The X6DLP-4G2 has eight (8) 240-pin DIMM sockets that can support up to 16 GB

of registered ECC DDR2-400 SDRAM. The memory bus is a dual-channel confi gu-

ration and memory modules must be installed in pairs (two at a time). All memory

modules used to populate the system should be the same size, type and speed.

SCSI Subsystem

The onboard Adaptec AIC-7902 SCSI controller supports four 80-pin SCA Ultra320

SCSI hard drives. (SCA = Single Connection Attachment.) The SCSI drives are

connected to an SCA backplane that provides power, bus termination and confi gura-

tion settings. The SCSI drives are hot-swap units.

PCI Expansion Slots

The X6DLP-4G2 has two 64-bit, 66 MHz (3.3V) PCI-X slots, two x8 PCI-Express

slots and one 32-bit, 33 MHz (5V) PCI slot. When confi gured as the X6DLP-4G2,

the 64-bit, 133 MHz PCI-X slot is available with the use of a riser card (included

with the system). (Alternatively, the optional CSE-RR1U-EL riser card may be used

to support an add-on card in the x8 PCI-Express slot.)

Ethernet Ports

The X6DLP-4G2 has one Intel 82573V and one Intel 82573L single port Ethernet

controllers to support two Gigabit LAN ports. (Supports 100/1000 BASE-T, RJ45

output.)

1-2

Chapter 1: Introduction

Onboard Controllers/Ports

An onboard IDE controller supports up to four UltraDMA/100 hard drives or ATAPI

devices. Onboard I/O backpanel ports include one COM port, a VGA port, two USB

ports, PS/2 mouse and keyboard ports and two GLAN (NIC) ports.

Other Features

Other onboard features that promote system health include voltage monitors, a

chassis intrusion header, auto-switching voltage regulators, chassis and CPU

overheat sensors, virus protection and BIOS rescue.

1-3

S

UPERSERVER 6014L-M4 User's Manual

8x PCI-Express (Slot 6)

8x PCI-Express (Slot 3)

SCSI Connector

AIC-

7901

PCI 33 MHz (Slot 1)

LAN

LAN

82573

82573

PCI-X 66 MHz (Slot 6)

PCI-X 66 MHz (Slot 5)

ATI

Rage

CPU1

Group A

Links0-7

Group B

Links0-7

Kybd/

Mouse

667 MT/s

E7520

MCH

6300ESB

LPC

S I/OBIOS

Floppy

CPU2

DDR2-400

DIMM 1A

DIMM 2A

DIMM 3A

DIMM 4A

DIMM 1B

DIMM 2B

DIMM 3B

DIMM 4B

SATA Ports (4)

IDE (ATA133)

USB Ports (4)

IPMI

COM
Ports

Note: This is a general block diagram. Please see Chapter 5 for details.

Figure 1-1 . Intel E7520 Chipset:

System Block Diagram

1-4

Chapter 1: Introduction

1-3 Server Chassis Features

The following is a general outline of the main features of the SC813MS-300C

chassis.

System Power

When confi gured as a SuperServer 6014L-M4, the SC813MS-300C chassis in-

cludes a single 300W power supply.

SCSI Subsystem

The SC813MS-300C chassis was designed to support four SCSI hard drives. These

drives are hot-swappable units.

Note: The operating system you use must have RAID support to enable the hot-

swap capability of the SCSI drives.

Control Panel

The SC813MS-300C's control panel provides important system monitoring and

control information. LEDs indicate power on, network activity, hard disk drive activ-

ity and system overheat conditions. The control panel also includes a main power

button and a system reset button.

Rear I/O Panel

The SC813MS-300C is a 1U rackmount chassis. Its I/O panel provides one PCI

expansion slot, one COM port (another is internal), two USB ports, PS/2 mouse and

keyboard ports, a VGA port and two Gb Ethernet ports. (See Figure 1-2.)

1-5

S

UPERSERVER 6014L-M4 User's Manual

Figure 1-2. Rear I/O Panel

Cooling System

The SC813MS-300C chassis has an innovative cooling design that features three

4-cm high-performance system cooling fans. Each of these fans plug into a chassis

fan header on the serverboard. An air shroud channels the airfl ow generated by

the fans to effi ciently cool the processor area of the system.

A fan speed control setting in BIOS allows fan speed to be determined by system

temperature [the recommended setting is 3-pin (Server)].

1-6

Chapter 1: Introduction

1-4 Contacting Supermicro

Headquarters

Address: SuperMicro Computer, Inc.
980 Rock Ave.
San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)
[e-mail] (Technical Support)
Web Site: www.supermicro.com

Europe

Address: SuperMicro Computer B.V.
Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)
[e-mail] (Technical Support)
[e-mail] (Customer Support)

Asia-Pacifi c

Address: SuperMicro, Taiwan
4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei County
Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [e-mail]
Tel: [phone], ext.132 or 139

1-7

S

UPERSERVER 6014L-M4 User's Manual

Notes

1-8

Chapter 2: Server Installation

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your SuperServer 6014L-M4

up and running. Following the steps in the order given should enable you to have

the system operational within a minimal amount of time. This quick setup assumes

that your 6014L-M4 system has come to you with the processors and memory

preinstalled. If your system is not already fully integrated with a serverboard,

processor(s), system memory etc., please turn to the chapter or section noted in

each step for details on installing specifi c components.

2-2 Unpacking the System

You should inspect the box the SuperServer 6014L-M4 was shipped in and note

if it was damaged in any way. If the server itself shows damage, you should fi le a

damage claim with the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the SuperServer 6014L-

M4. It should be situated in a clean, dust-free area that is well ventilated. Avoid

areas where heat, electrical noise and electromagnetic fi elds are generated. You

will also need it placed near a grounded power outlet. Read the Rack and Server

Precautions in the next section.

2-3 Preparing for Setup

The box the SuperServer 6014L-M4 was shipped in should include two sets of

rail assemblies, six rail mounting brackets and the mounting screws you will need

to install the system into the rack. Follow the steps in the order given to complete

the installation process in a minimal amount of time. Please read this section in

its entirety before you begin the installation procedure outlined in the sections that

follow.

2-1

S

UPERSERVER 6014L-M4 User's Manual

Choosing a Setup Location

- Leave enough clearance in front of the rack to enable you to open the front door

completely (~25 inches).

- Leave approximately 30 inches of clearance in the back of the rack to allow for

suffi cient airfl ow and ease in servicing.

- This product is for installation only in a Restricted Access Location (dedicated

equipment rooms, service closets, etc.).

!

Warnings and Precautions!

!

Rack Precautions

- Ensure that the leveling jacks on the bottom of the rack are fully extended to the

fl oor with the full weight of the rack resting on them.

- In a single rack installation, stabilizers should be attached to the rack.

- In multiple rack installations, the racks should be coupled together.

- Always make sure the rack is stable before extending a component from the

rack.

- You should extend only one component at a time - extending two or more simul-

taneously may cause the rack to become unstable.

Server Precautions

- Review the electrical and general safety precautions in Chapter 4.

- Determine the placement of each component in the rack before you install the

rails.

- Install the heaviest server components on the bottom of the rack fi rst, and then

work up.

- Use a regulating uninterruptible power supply (UPS) to protect the server from

power surges, voltage spikes and to keep your system operating in case of a power

failure.

-

Allow the power supply units and hot plug SCSI drives to cool before touching

them.

-

Always keep the rack's front door and all panels and components on the servers

closed when not servicing to maintain proper cooling.

2-2

Chapter 2: Server Installation

Rack Mounting Considerations

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating tempera-

ture of the rack environment may be greater than the ambient temperature of the

room. Therefore, consideration should be given to installing the equipment in an

environment compatible with the manufacturer’s maximum rated ambient tempera-

ture (Tmra).

Reduced Airfl ow

Equipment should be mounted into a rack so that the amount of airfl ow required

for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition does not

arise due to uneven mechanical loading.

Circuit Overloading

Consideration should be given to the connection of the equipment to the power

supply circuitry and the effect that any possible overloading of circuits might have

on overcurrent protection and power supply wiring. Appropriate consideration of

equipment nameplate ratings should be used when addressing this concern.

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack itself

should be grounded. Particular attention should be given to power supply connec-

tions other than the direct connections to the branch circuit (i.e. the use of power

strips, etc.).

2-3

S

UPERSERVER 6014L-M4 User's Manual

2-4 Installing the System into a Rack

This section provides information on installing the SuperServer 6014L-M4 into a

rack unit with the rack rails provided. If the server has already been mounted into

a rack, you can skip ahead to Sections 2-5 and 2-6. There are a variety of rack

units on the market, which may mean the assembly procedure will differ slightly.

You should also refer to the installation instructions that came with the rack unit

you are using.

Identifying the Sections of the Rack Rails

You may have received rack rail hardware with the SuperServer 6014L-M4. (Two

front inner rails should already be attached to the chassis.) This hardware consists

of two rear inner rails that secure to the chassis, one on each side just behind the

preinstalled front inner rails. Note that these two rails are left/right specifi c.

Installing the Rear Inner Rails

First, locate the right rear inner rail (the rail that will be used on the right side of

the chassis when you face the front of the chassis). Align the two square holes

on the rail against the hooks on the right side of the chassis. Securely attach the

rail to the chassis with M4 fl at head screws. Repeat these steps to install the left

rear inner rail to the left side of the chassis (see Figure 2-1). You will also need to

attach the rail brackets when installing into a telco rack.

Locking Tabs: Both chassis rails have a locking tab, which serves two functions.

The fi rst is to lock the server into place when installed and pushed fully into the

rack, which is its normal position. Secondly, these tabs also lock the server in place

when fully extended from the rack. This prevents the server from coming completely

out of the rack when you pull it out for servicing.

2-4

Chapter 2: Server Installation

Figure 2-1. Installing Rear Inner Chassis Rails

Installing the Rack Rails

Determine where you want to place the SuperServer 6014L-M4 in the rack (see

Rack and Server Precautions in Section 2-3). Position the chassis rail guides at

the desired location in the rack, keeping the sliding rail guide facing the inside of

the rack. Screw the assembly securely to the rack using the brackets provided.

Attach the other assembly to the other side of the rack, making sure that both are

at the exact same height and with the rail guides facing inward.

2-5

S

UPERSERVER 6014L-M4 User's Manual

Installing the Server into the Rack

You should now have rails attached to both the chassis and the rack unit. The next

step is to install the server into the rack. Do this by lining up the rear of the chas-

sis rails with the front of the rack rails. Slide the chassis rails into the rack rails,

keeping the pressure even on both sides (you may have to depress the locking

tabs when inserting). See Figure 2-2.

When the server has been pushed completely into the rack, you should hear the

locking tabs "click". Finish by inserting and tightening the thumbscrews that hold

the front of the server to the rack.

Figure 2-2. Installing the Server into a Rack

(with optional front bezel shown)

2-6

Chapter 2: Server Installation

Installing the Server into a Telco Rack

If you are installing the SuperServer 6014L-M4 into a Telco type rack, follow the di-

rections given on the previous pages for rack installation. The only difference in the

installation procedure will be the positioning of the rack brackets to the rack. They

should be spaced apart just enough to accommodate the width of the telco rack.

Figure 2-3. Installing the Server into a Telco Rack

(with optional front bezel shown)

2-7

S

UPERSERVER 6014L-M4 User's Manual

2-5 Checking the Motherboard Setup

After you install the 6014L-M4 in the rack, you will need to open the unit to make sure

the motherboard is properly installed and all the connections have been made.

1. Accessing the inside of the system (Figure 2-4)

First, grasp the two handles on either side and pull the unit straight out until it locks

(you will hear a "click"). Next, depress the two buttons on the top of the chassis to

release the top cover. There is a large rectangular recess in the middle front of the

top cover to help you push the cover away from you until it stops. You can then lift

the top cover from the chassis to gain full access to the inside of the server.

2. Check the CPUs (processors)

You may have one or two processors already installed into the system board. Each

processor should have its own heatsink attached. See Chapter 5 for instructions

on processor installation.

3. Check the system memory

Your 6014L-M4 server system may have come with system memory already in-

stalled. Make sure all DIMMs are fully seated in their slots. For details on adding

system memory, refer to Chapter 5.

4. Installing add-on cards

If desired, you can install an add-on card to the system. See Chapter 5 for details

on installing a PCI add-on card.

5. Check all cable connections and airfl ow

Make sure all power and data cables are properly connected and not blocking the

airfl ow. See Chapter 5 for details on cable connections. Also, check the air seals

for damage. The air seals are located under the chassis fans and beneath the

frame cross section that separates the drive bay area from the motherboard area

of the chassis.

2-8

Chapter 2: Server Installation

Figure 2-4.

Accessing the Inside of the SuperServer 6014L-M4

2-9

S

UPERSERVER 6014L-M4 User's Manual

2-6 Checking the Drive Bay Setup

Next, you should check to make sure the peripheral drives and the SCSI drives

and SCSI backplane have been properly installed and all essential connections

have been made.

1. Accessing the drive bays

All drives can be accessed from the front of the server. For servicing the CD-ROM

drive, you will need to remove the top chassis cover. The SCSI disk drives can

be installed and removed from the front of the chassis without removing the top

chassis cover.

2. Installing a CD-ROM drive

Refer to Chapter 6 if you need to reinstall a CD-ROM drive to the system.

3. Check the SCSI disk drives

Depending upon your system's confi guration, your system may have one or more

SCSI drives already installed. If you need to install SCSI drives, please refer to

the appropriate section in Chapter 6.

4. Check the airfl ow

Airfl ow is provided by three high-performance 4-cm input fans. The system com-

ponent layout was carefully designed to promote suffi cient airfl ow through the small

1U rackmount space. Also note that all power and data cables have been routed

in such a way that they do not block the airfl ow generated by the fans.

5. Supplying power to the system

The last thing you must do is to provide input power to the system. Plug the power

cord from the power supply unit into a high-quality power strip that offers protec-

tion from electrical noise and power surges. It is recommended that you use an

uninterruptible power supply (UPS). Finish by pressing the power button on the

front of the chassis.

2-10

Chapter 3: System Interface

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the control panel as well as others on the SCSI drive

carriers to keep you constantly informed of the overall status of the system as well

as the activity and health of specifi c components. There are also two buttons on

the chassis control panel. This chapter explains the meanings of all LED indicators

and the appropriate response you may need to take.

3-2 Control Panel Buttons

There are two push-button buttons located on the front of the chassis: a reset but-

ton and a power on/off button.

 RESET:

 POWER: This is the main power switch, which is used to apply or turn off

the main system power. Turning off system power with this button removes the

main power but keeps standby power supplied to the system.

The reset switch reboots the system.

3-1

S

UPERSERVER 6014L-M4 User's Manual

3-3 Control Panel LEDs

The control panel located on the front of the chassis has fi ve LEDs. These LEDs

provide you with critical information related to different parts of the system. This

section explains what each LED indicates when illuminated and any corrective ac-

tion you may need to take.



Overheat/Fan Fail: When this LED fl ashes, it indicates a fan failure. When

on continuously it indicates an overheat condition, which may be caused by cables

obstructing the airfl ow in the system or the ambient room temperature being too

warm. Check the routing of the cables and make sure all fans are present and

operating normally. You should also check to make sure that the chassis covers

are installed. Finally, verify that the heatsinks are installed properly (see Chapter

5). This LED will remain fl ashing or on as long as the indicated condition exists.

2

 NIC2: Indicates network activity on JLAN2 when fl ashing .

1

 NIC1: Indicates network activity on JLAN1 when fl ashing.

 HDD: Channel activity for all HDDs. This light indicates CD-ROM and SCSI

drive activity when fl ashing.

3-2