Supermicro SUPERSERVER 6013P-8 User Manual

®

SUPERSERVER 6013P-8

USER’S MANUAL

1.1b

SUPER

The information in this User’s Manual has been carefully reviewed and is believed to be
accurate. The vendor assumes no responsibility for any inaccuracies that may be
contained in this document, makes no commitment to update or to keep current the
information in this manual, or to notify any person or organization of the updates.

Please
Note: For the most up-to-date version of this manual, please see our
web site at www.supermicro.com.

SUPERMICRO COMPUTER reserves the right to make changes to the product described in
this manual at any time and without notice. This product, including software, if any, and
documentation may not, in whole or in part, be copied, photocopied, reproduced, translated
or reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO COMPUTER BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM
THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, THE VENDOR
SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED
OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING,
INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR
DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of
Santa Clara shall be the exclusive venue for the resolution of any such disputes.
Supermicro's total liability for all claims will not exceed the price paid for the hardware
product.

Unless you request and receive written permission from SUPER MICRO COMPUTER, you
may not copy any part of this document.

Information in this document is subject to change without notice. Other products and
companies referred to herein are trademarks or registered trademarks of their respective
companies or mark holders.

Copyright © 2003 by SUPER MICRO COMPUTER INC.
All rights reserved.

Printed in the United States of America

Preface

About This Manual

This manual is written for professional system integrators and PC technicians.
It provides information for the installation and use of the SuperServer 6013P-8.
Installation and maintainance should be performed by experienced technicians
only.

The SuperServer 6013P-8 is a high-end, dual Xeon processor 1U rackmount
server based on the SC812S-400 1U rackmount server chassis and the X5DPR­8G2+ serverboard, which supports single or dual Xeon processors of up to 3.20
GHz at a Front Side (system) Bus speed of 533/400 MHz and up to 12 GB of
DDR-266/200 (PC2100/1600) low-profile SDRAM memory.

Manual Organization

Chapter 1: Introduction

The first chapter provides a checklist of the main components included with the
server system and describes the main features of the SUPER X5DPR-8G2+
serverboard and the SC812S-400 chassis, which make up the SuperServer
6013P-8.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer 6013P-8
into a rack and check out the server configuration prior to powering up the
system. If your server was ordered without processor and memory components,
this chapter will refer you to the appropriate sections of the manual for their
installation.

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions
and information provided by the control panel on the chassis as well as
other LEDs located throughout the system.

iii

Preface

SUPERSERVER 6013P-8 Manual

iv

Chapter 4: System Safety

You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 6013P-8.

Chapter 5: Advanced Serverboard Setup

Chapter 5 provides detailed information on the X5DPR-8G2+ serverboard,
including the locations and functions of connectors, headers and jumpers.
Refer to this chapter when adding or removing processors or main memory
and when reconfiguring the serverboard.

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the 1U SC812S-400 rackmount
server chassis. You should follow the procedures given in this chapter when
installing, removing or reconfiguring SCSI or peripheral drives and when replacing
the system power supply unit and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed
information on running the CMOS Setup Utility.

Appendix A: BIOS POST Messages

Appendix B: BIOS POST Codes

Appendix C: System Specifications

v

Preface

Notes

SUPERSERVER 6013P-8 Manual

vi

Table of Contents

Preface

About This Manual ....................................................................................................... ii i

Manual Organization .................................................................................................... ii i

Chapter 1: Introduction to the SuperServer 6013P-8

1-1 Overview ............................................................................................................ 1- 1

1- 2 Server Chassis Features ................................................................................ 1-2

1-3 Serverboard Features ...................................................................................... 1- 4

1- 4 Contacting Supermicro ................................................................................... 1-6

Chapter 2: Server Installation

2-1 Overview ............................................................................................................ 2- 1

2- 2 Unpacking the SuperServer 6013P-8............................................................. 2- 1

2- 3 Preparing for Setup ......................................................................................... 2-1

Choosing a Setup Location...................................................................... 2-2

Rack Precautions...................................................................................... 2- 2

Server Precautions.................................................................................... 2-2

2-4 Installing the SuperServer 6013P-8 into a Rack .......................................... 2-3

Identifying the Sections of the Rack Rails ............................................ 2-3

Installing the Chassis Rails.......................................................................2-4

Installing the Rack Rails ............................................................................2-4

Installing the Server into the Rack ...........................................................2-5

Installing the Server into a Telco Rack ....................................................2-6

2- 5 Checking the Serverboard Setup ................................................................... 2-7

2-6 Checking the Drive Bay Setup....................................................................... 2-9

Chapter 3: System Interface

3-1 Overview ............................................................................................................ 3- 1

3-2 Control Panel Buttons..................................................................................... 3 -1

Reset.......................................................................................................... 3-1

NMI ............................................................................................................. 3-1

Power ......................................................................................................... 3 -2

3- 3 Control Panel LEDs......................................................................................... 3-2

Overheat ..................................................................................................... 3 -2

NIC2 ............................................................................................................ 3- 2

NIC1 ............................................................................................................ 3- 3

HDD ............................................................................................................ 3-3

Power ......................................................................................................... 3 -3

3- 4 SCSI Drive Carrier LEDs................................................................................. 3-3

3-5 Serverboard LEDs ............................................................................................ 3-4

Chapter 4: System Safety

4-1 Electrical Safety Precautions...........................................................................4-1

4- 2 General Safety Precautions .............................................................................4-2

4-3 ESD Precautions ...............................................................................................4-3

4- 4 Operating Precautions ......................................................................................4-4

Chapter 5: Advanced Serverboard Setup

5-1 Handling the X5DPR-8G2+ Serverboard ..........................................................5-1

5-2 PGA Processor and Heatsink Installation ......................................................5-2

5- 3 Connecting Cables ............................................................................................5-5

Connecting Data Cables ............................................................................5-5

Connecting Power Cables ..........................................................................5-5

Connecting the Control Panel ...................................................................5-6

5-4 I/O Ports .............................................................................................................5-7

5- 5 Installing Memory ..............................................................................................5-7

5- 6 Adding PCI Cards ..............................................................................................5-9

5-7 Serverboard Details .........................................................................................5-10

X5DPR-8G2+ Layout............................................................................... 5-10

X5DPR-8G2+ Quick Reference.............................................................. 5-11

5- 8 Connector Definitions ......................................................................................5-12

ATX Power Connection ........................................................................... 5-12

PWR_SEC Connection ........................................................................... 5-12

NMI Button............................................................................................... 5-12

Power LED............................................................................................... 5-12

HDD LED ................................................................................................. 5-12

NIC1 LED ................................................................................................. 5-13

NIC2 LED ................................................................................................. 5-13

Overheat LED .......................................................................................... 5-13

Power Fail LED ....................................................................................... 5-13

Reset Button ........................................................................................... 5-13

Power Button........................................................................................... 5-14

Universal Serial Bus ............................................................................... 5-14

Extra USB Headers ................................................................................ 5-14

Serial Ports ............................................................................................. 5-15

ATX PS/2 Keyboard & Mouse Ports..................................................... 5-15

Fan Headers ............................................................................................ 5-15

vii

Table of Contents

SUPERSERVER 6013P-8 Manual

viii

GLAN 1/2 (Ethernet Ports) .................................................................... 5-15

Power LED/Speaker/NMI........................................................................ 5-16

Third Power Supply Fail Header............................................................ 5-16

Chassis Intrusion .................................................................................... 5-16

Wake-On-LAN.......................................................................................... 5-17

Wake-On-Ring ......................................................................................... 5-17

Keylock .................................................................................................... 5-17

5- 9 Jumper Settings............................................................................................. 5-18

Explanation of Jumpers.......................................................................... 5-18

CMOS Clear ............................................................................................ 5-18

GLAN Enable/Disable............................................................................. 5-19

VGA Enable/Disable ............................................................................... 5-19

Front Side Bus Speed............................................................................ 5-19

SCSI Enable/Disable .............................................................................. 5-19

SCSI Termination Enable/Disable ......................................................... 5-20

Watch Dog Enable/Disable.................................................................... 5-20

5-10 Onboard Indicators ........................................................................................ 5-21

GLAN1/GLAN2 LEDs .............................................................................. 5-21

5-11 Floppy/Hard Drive and SCSI Connections .................................................. 5-22

Floppy Connector .................................................................................... 5-22

IDE Connectors ....................................................................................... 5-23

Ultra320 SCSI Connectors ..................................................................... 5-23

5-12 Installing Software Drivers ............................................................................ 5-24

5-13 Supero Doctor III............................................................................................ 5-27

Chapter 6: Advanced Chassis Setup

6- 1 Static-Sensitive Devices ................................................................................. 6-1

6- 2 Control Panel ................................................................................................... 6-2

6-3 System Fans .................................................................................................... 6-3

System Fan Failure .................................................................................. 6-3

Replacing System Cooling Fans............................................................. 6-3

6-4 Drive Bay Installation/Removal ....................................................................... 6-4

Accessing the Drive Bays ....................................................................... 6-4

SCSI Drive Installation.............................................................................. 6-5

CD-ROM and Floppy Drive Installation ................................................... 6-7

6- 5 Power Supply................................................................................................... 6-8

Power Supply Failure ............................................................................... 6 -8

Removing/Replacing the Power Supply .................................................. 6-8

Table of Contents

ix

Chapter 7: BIOS

7-1 Introduction....................................................................................................... 7- 1

7- 2 Running Setup ................................................................................................. 7-2

7-3 Main BIOS Setup ............................................................................................ 7-2

The Main BIOS Setup Menu.................................................................... 7- 3

7- 4 Advanced Setup............................................................................................... 7 -6

7-5 Security .......................................................................................................... 7-13

7-6 Power .............................................................................................................. 7-15

7-7 Boot................................................................................................................. 7-17

7-8 PIR .................................................................................................................. 7-19

7-9 Exit.................................................................................................................. 7-21

Appendices:

Ap pe n d i x A: B I O S P O S T Me s s a g es ....................................................................... A - 1

Appendix B: BIOS Post Codes ............................................................................... B - 1

Appendix C: System Specifications ....................................................................... C-1

SUPERSERVER 6013P-8 User's Manual

x

Notes

Chapter 1

Introduction to the SuperServer 6013P-8

1-1 Overview

The Supermicro SuperServer 6013P-8 is a high-end dual processor, 1U
rackmount server that features some of the most advanced technology
currently available. The SuperServer 6013P-8 is comprised of two main
subsystems: the SC812S-400 1U rackmount chassis and the X5DPR-8G2+ dual
Xeon processor serverboard. Please refer to our web site for information
on operating systems that have been certified for use with the SuperServer
6013P-8. (www.supermicro.com)

In addition to the mainboard and chassis, various hardware components
may have been included with your SuperServer 6013P-8, as listed below:

! Two (2) 1U CPU heatsinks (SNK-P0003) and two sets of heatsink

retention clips (for 604-and 603-pin processors, two in each set)

! One (1) 3.5" slim floppy drive

! One (1) slim CD-ROM drive

! Two (2) riser cards (CSE-RR1U-X and CSE-RR1U-XLP)

! One (1) SCA SAF-TE compliant SCSI backplane

! Three (3) SCA 1-inch high SCSI drive carriers

! SCSI Accessories

One (1) internal 68-pin Ultra320/160 SCSI cable

One (1) SCSI manual

! Rackmount hardware (with screws):

Two (2) rack rail assemblies

Six (6) brackets for mounting the rack rails to a rack/telco rack

Chapter 1: Introduction

1-1

SUPERSERVER 6013P-8 Manual

1-2

! One (1) CD-ROM containing drivers and utilities:

! SuperServer 6013P-8 User's Manual

1-2 Mainboard Features

At the heart of the SuperServer 6013P-8 lies the X5DPR-8G2+, a dual Intel
Xeon processor serverboard designed to provide maximum performance.
Below are the main features of the X5DPR-8G2+.

Chipset

The X5DPR-8G2+ is based on Intel's E7501 chipset, which is a high-perfor­mance chipset designed for dual-processor servers (see Figure 1-1).

The E7501 chipset consists of four major components: the Memory Control­ler Hub (MCH), the I/O Controller Hub 3 (ICH3), the PCI-X 64-bit Hub 2.0
(P64H2) and the 82808AA Host Channel Adapter (VxB).

The MCH has four hub interfaces, one to communicate with the ICH3 and
three for high-speed I/O communications. The MCH employs a 144-bit wide
memory bus for a DDR-266 (PC2100) memory interface, which provides a
total bandwidth of up to 4.2 GB/s. The ICH3 interface is a 266 MB/sec
point-to-point connection using an 8-bit wide, 66 MHz base clock at a 4x
data transfer rate. The P64H2 interface is a 1 GB/s point-to-point connec­tion using a 16-bit wide, 66 MHz base clock at a 8x data transfer rate.

The ICH3 I/O Controller Hub provides various integrated functions, including
a two-channel UDMA100 bus master IDE controller, USB host controllers, a
System Management Bus controller and an AC'97 compliant interface.

The P64H2 PCI-X Hub provides a 16-bit connection to the MCH for high­performance IO capability and the 64-bit PCI-X interface.

1-3

Chapter 1: Introduction

Processors

The X5DPR-8G2+ supports single or dual Intel 604/603-pin Xeon processors of up
to 3.20 GHz at a 533/400 MHz FSB. Please refer to the support section of our
web site for a complete listing of supported processors (http://
www.supermicro.com/TechSupport.htm).

Memory

The X5DPR-8G2+ has 6 184-pin, DIMM slots that can support up to 12 GB of
low-profile, registered ECC DDR-266/200 (PC2100/1600) SDRAM. Module
sizes of 128 MB, 256 MB, 512 MB, 1 GB and 2 GB may be used to populate
the DIMM slots. (This serverboard has has been designed to support 2GB
DIMM modules for each memory slot, but it has only been validated with 1GB
memory modules. Memory modules of different sizes and speeds should not be
mixed.)

Onboard SCSI

Onboard SCSI is provided with an Adaptec AIC-7902 SCSI controller chip,
which supports dual channel, Ultra320 SCSI at a burst throughput rate of
320 MB/sec. The X5DPR-8G2+ provides two SCSI ports. A QLogic GEM318
controller is used for the SAF-TE compliant SCSI backpanel.

PCI Expansion Slots

The X5DPR-8G2+ has one 64-bit, 133 MHz PCI-X slot and one slim 64-bit, 66
MHz PCI slot. A "butterfly" riser card is included with the server. This riser
card fits into the 133 MHz PCI-X slot and was designed specially for the SC812S­400 chassis to support the use of one standard PCI card and one low profile (half­height, half-length) PCI card. Several jumpers on the motherboard are used to
change the speeds of these slots if needed (see Chapter 5).

ATI Graphics Controller

The X5DPR-8G2+ features an integrated ATI video controller based on the
Rage XL graphics chip. Rage XL fully supports sideband addressing and
AGP texturing. This onboard graphics package can provide a bandwidth of
up to 512 MB/sec over a 32-bit graphics memory bus.

SUPERSERVER 6013P-8 Manual

1-4

Onboard Controllers/Ports

The X5DPR-8G2+ includes one floppy drive controller and two onboard IDE con­trollers, which support up to four hard drives or ATAPI devices. Backpanel I/O
ports include one COM port, two USB ports, PS/2 mouse and keyboard ports,
a video (monitor) port and an external SCSI port. An Intel 82546 Ethernet
controller is included to support two Gb LAN ports.

Other Features

Other onboard features are included to promote system health. These in­clude various voltage monitors, two CPU temperature sensors, four fan
speed sensors, a chassis intrusion header, auto-switching voltage regula­tors, chassis and CPU overheat sensors, virus protection and BIOS rescue.

PCI-X Slot 6, SXB

MCH

533/400 MH z Sy stem B us

266 MHz Memory Bus

ATA 100

Ports

P64H2

Processor 1 Processor 0

2-Channel DDR SDRAM

PCI-X Slot 5, Gb LAN

ICH3 -S

USB 1.1

Ports

SMBus

Super IO

ATI

Graphics

P64H2

PCI-X Slots 1-3
PCI-X Slot 4, SCSI

Figure 1-1. E7501 Chipset Block Diagram

1-5

Chapter 1: Introduction

1-3 Server Chassis Features

The SC812S-400 is Supermicro's second-generation 1U chassis and features
three hard drive bays, two front side USB ports and a revolutionary cooling design
that can keep today's most powerful processors running well below their tempera­ture thresholds. The following is a general outline of the main features of the
SC812S-400 chassis.

System Power

When configured as a SuperServer 6013P-8, the SC812S-400 chassis includes
a 400W cold-swap power supply.

SCSI Subsystem

The SCSI subsystem supports three 80-pin SCA Ultra320 SCSI hard drives. (Any
standard 1" drives are supported. SCA = Single Connection Attachment.) The
SCSI drives are connected to an SCA backplane that provides power, bus termi­nation and configuration settings. The SCSI drives are also hot-swap units.

Control Panel

The SC812S-400 control panel provides important system monitoring and control
information. LEDs indicate power on, network activity, hard disk drive ac­tivity and system overheat conditions. Also present are a main power
button, a system reset button and an NMI (non-maskable interrupt) button.

I/O Backplane

The SC812S-400 is a 1U rackmount chassis. Its I/O backplane provides one full­height full-length and one half-height half-length PCI slots, one COM port
(the other is internal), one VGA port, two USB ports, PS/2 mouse and
keyboard ports and two Ethernet (LAN) ports and an external SCSI port.
(See Figure 1-2.)

SUPERSERVER 6013P-8 Manual

1-6

Cooling System

The SC812S-400 chassis' revolutionary cooling design has been optimized to
provide sufficient cooling for dual Xeon configurations. The SC812S-400 includes
two heavy duty 10-cm blower fans located in the middle of the chassis. These
fans operate continuously at full rpm. If they break down, the ambient air tem­perature inside the chassis will rise and activate an overheat LED.

Figure 1-2. I/O Backplane

Ethernet PortsUSB Ports

Mouse PortKeyboard Port

COM1 Port

Low Profile PCI Slot Standard PCI Slot

VGA Port Ext. SCSI Port

1-7

Chapter 1: Introduction

1-4 Contacting Supermicro

Headquarters

Address: SuperMicro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)
Web Site: www.supermicro.com

Europe

Address: SuperMicro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands
Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Asia-Pacific

Address: SuperMicro, Taiwan

D5, 4F, No. 16 Chien-Ba Road

Chung-Ho 235, Taipei Hsien, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [e-mail]
Tel: [phone], ext.132 or 139

SUPERSERVER 6013P-8 Manual

1-8

Notes

Chapter 2: Server Installation

2-1

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your SuperServer
6013P-8 up and running. Following these steps in the order given should
enable you to have the system operational within a minimum amount of time.
This quick setup assumes that your SuperServer 6013P-8 system has come
to you with the processors and memory preinstalled. If your system is not
already fully integrated with a serverboard, processors, system memory
etc., please turn to the chapter or section noted in each step for details on
installing specific components.

2-2 Unpacking the SuperServer 6013P-8

You should inspect the box the SuperServer 6013P-8 was shipped in and
note if it was damaged in any way. If the server itself shows damage you
should file a damage claim with the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the SuperServer
6013P-8. It should be situated in a clean, dust-free area that is well venti­lated. Avoid areas where heat, electrical noise and electromagnetic fields
are generated. You will also need it placed near a grounded power outlet.
Read the Rack and Server Precautions in the next section.

2-3 Preparing for Setup

The box the SuperServer 6013P-8 was shipped in should include two sets
of rail assemblies, two rail mounting brackets and the mounting screws you
will need to install the system into the rack. Follow the steps in the order
given to complete the installation process in a minimum amount of time.
Please read this section in its entirety before you begin the installation
procedure outlined in the sections that follow.

2-2

SUPERSERVER 6013P-8 Manual

Choosing a Setup Location:

- Leave enough clearance in front of the rack to enable you to open

the front door completely (~25 inches).

- Leave approximately 30 inches of clearance in the back of the rack

to allow for sufficient airflow and ease in servicing.

Rack Precautions:

- Ensure that the leveling jacks on the bottom of the rack are fully

extended to the floor with the full weight of the rack resting on them.

- In single rack installation, stabilizers should be attached to the rack.

- In multiple rack installations, the racks should be coupled together.

- Always make sure the rack is stable before extending a component

from the rack.

- You should extend only one component at a time - extending two or

more simultaneously may cause the rack to become unstable.

Server Precautions:

- Review the electrical and general safety precautions in Chapter 4.

- Determine the placement of each component in the rack before you

install the rails.

- Install the heaviest server components on the bottom of the rack

first, and then work up.

- Use a regulating uninterruptible power supply (UPS) to protect the
server from power surges, voltage spikes and to keep your
system operating in case of a power failure.

- Allow the hot plug SCSI drives and power supply units to cool before

touching them.

- Always keep the rack's front door and all panels and components on

the servers closed when not servicing to maintain proper cooling.

!

!

Warnings and Precautions!

Chapter 2: Server Installation

2-3

Rack Mounting Considerations

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating
temperature of the rack environment may be greater than the ambient
temperature of the room. Therefore, consideration should be given to
installing the equipment in an environment compatible with the manufacturer’s
maximum rated ambient temperature (Tmra).

Reduced Airflow

Equipment should be mounted into a rack so that the amount of airflow
required for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition does
not arise due to uneven mechanical loading.

Circuit Overloading

Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply con­nections other than the direct connections to the branch circuit (i.e. the use of
power strips, etc.).

2-4

SUPERSERVER 6013P-8 Manual

2-4 Installing the SuperServer 6013P-8 into a Rack

This section provides information on installing the SuperServer 6013P-8 into
a rack unit. If the 6013P-8 has already been mounted into a rack, you can
skip ahead to Sections 2-5 and 2-6. There are a variety of rack units on
the market, which may mean the assembly procedure will differ slightly.
The following is a guideline for installing the 6013P-8 into a rack with the
rack rails provided. You should also refer to the installation instructions
that came with the rack unit you are using.

Identifying the Sections of the Rack Rails:

You should have received two rack rail assemblies with the SuperServer
6013P-8. Each of these assemblies consist of three sections: an inner
fixed chassis rail that secures to the 6013P-8 (A) and an outer fixed rack
rail that secures directly to the rack itself (B). A sliding rail guide sand­wiched between the two should remain attached to the fixed rack rail.
(See Figure 2-1.) The A and B rails must be detached from each other to
install.

To remove the fixed chassis rail (A), pull it out as far as possible - you
should hear a "click" sound as a locking tab emerges from inside the rail
assembly and locks the inner rail. Then depress the locking tab to pull
the inner rail completely out. Do this for both the left and right side rack
rail assemblies.

Figure 2-1. Identifying the Sections of the Rack Rails

A

B

Locking Tab

Mounting Holes

Chapter 2: Server Installation

2-5

Installing the Chassis Rails:

Position the fixed chassis rail sections you just removed along the side of
the 6013P-8 making sure the screw holes line up. Note that these two rails
are left/right specific. Screw the rail securely to the side of the chassis
(see Figure 2-2). Repeat this procedure for the other rail on the other side
of the chassis. You will also need to attach the rail brackets when installng
into a telco rack.

Locking Tabs: As you have seen, both chassis rails have a locking tab,
which serves two functions. The first is to lock the server into place
when installed and pushed fully into the rack, which is its normal position.
Secondly, these tabs also lock the server in place when fully extended
from the rack. This prevents the server from coming completely out of
the rack when you pull it out for servicing.

Figure 2-2. Installing Chassis Rails

Installing the Rack Rails:

Determine where you want to place the SuperServer 6013P-8 in the rack.
(See Rack and Server Precautions in Section 2-3.) Position the fixed rack
rail/sliding rail guide assemblies at the desired location in the rack, keeping
the sliding rail guide facing the inside of the rack. Screw the assembly
securely to the rack using the brackets provided. Attach the other assem-

2-6

SUPERSERVER 6013P-8 Manual

Figure 2-3. Installing the Server into a Rack

Installing the Server into the Rack:

You should now have rails attached to both the chassis and the rack
unit. The next step is to install the server into the rack. Do this by
lining up the rear of the chassis rails with the front of the rack rails.
Slide the chassis rails into the rack rails, keeping the pressure even on
both sides (you may have to depress the locking tabs when inserting).
See Figure 2-3.

When the server has been pushed completely into the rack, you should
hear the locking tabs "click". Finish by inserting and tightening the
thumbscrews that hold the front of the server to the rack.

bly to the other side of the rack, making sure both are at the exact same height
and with the rail guides facing inward.

Chapter 2: Server Installation

2-7

Figure 2-4. Installing the Server into a Telco Rack

Installing the Server into a Telco Rack:

If you are installing the SuperServer 6013P-8 into a Telco type rack, follow
the directions given on the previous pages for rack installation. The only
difference in the installation procedure will be the positioning of the rack
brackets to the rack. They should be spaced apart just enough to
accommodate the width of the telco rack.

2-8

SUPERSERVER 6013P-8 Manual

2-5 Checking the Serverboard Setup

After you install the 6013P-8 in the rack, you will need to open the unit to
make sure the serverboard is properly installed and all the connections
have been made.

1. Accessing the inside of the 6013P-8 (see Figure 2-5):

First, release the retention screws that secure the unit to the rack.
Grasp the two handles on either side and pull the unit straight out until it
locks (you will hear a "click"). Next, depress the two buttons on the top
of the chassis to release the top cover. There is a large rectangular
recess in the middle front of the top cover to help you push the cover
away from you until it stops. You can then lift the top cover from the
chassis to gain full access to the inside of the server.

2. Check the CPUs (processors):

You should have one or two processors already installed into the
serverboard. Each processor needs its own heatsink. See Chapter 5
for instructions on processor and heatsink installation.

3. Verify the proper CPU clock ratio setting:

If the CPU speed is not automatically detected you will need to set the
correct speed with the BIOS Setup utility. See the CPU Frequency Ratio
settings in BIOS (Chapter 7) for setting the proper CPU speed. (Most
processor speeds are automatically detected so this step should be un­necessary.)

4. Check the system memory:

Your 6013P-8 server system may have come with system memory al­ready installed. Make sure all DIMMs are fully seated in their slots. For
details on adding system memory, refer to Chapter 5.

5. Installing add-on cards:

If desired, you can install add-on cards to the system. See Chapter 5 for
details on installing PCI add-on cards.

Chapter 2: Server Installation

2-9

Figure 2-5. Accessing the Inside of the SuperServer 6013P-8

6. Check all cable connections and airflow:

Make sure all power and data cables are properly connected and not
blocking the chassis airflow. See Chapter 5 for details on cable connec­tions. Also, check the air seals for damage. The air seals are located
under the blower fan and beneath the frame cross section that sepa­rates the drive bay area from the serverboard area of the chassis.

2-10

SUPERSERVER 6013P-8 Manual

2-6 Checking the Drive Bay Setup

Next, you should check to make sure the peripheral drives and the SCSI
drives and SCA backplane have been properly installed and all connections
have been made.

1. Accessing the drive bays:

All drives are accessable from the front of the server. For servicing the
CD-ROM and floppy drives, you will need to remove the top chassis
cover. The SCSI disk drives can be installed and removed from the front
of the chassis without removing the top chassis cover.

2. CD-ROM and floppy disk drives:

A slim CD-ROM and a floppy drive should be preinstalled in your server.
Refer to Chapter 6 if you need to reinstall a CD-ROM and/or floppy disk
drive to the system.

3. Check the SCSI disk drives:

Depending upon your system's configuration, your system may have one
or more drives already installed. If you need to install SCSI drives, please
refer to Chapter 6.

4. Check the airflow:

Airflow is provided by two heavy duty 10-cm blower fans. The system
component layout was carefully designed to direct sufficient cooling air­flow to the components that generate the most heat. Note that all power
and data cables have been routed in such a way that they do not block
the airflow generated by the fans.

5. Supplying power to the system:

The last thing you must do is to provide input power to the system. Plug
the power cord from the power supply unit into a high-quality power
strip that offers protection from electrical noise and power surges. It is
recommended that you use an uninterruptible power supply (UPS).

Chapter 3: System Interface

3-1

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the control panel as well as others on the SCSI
drive carriers to keep you constantly informed of the overall status of the
system as well as the activity and health of specific components. There
are also two buttons on the chassis control panel and an on/off switch on
the power supply.

3-2 Control Panel Buttons

There are three push-button buttons located on the front of the chassis.
These are (in order from left to right) a reset button, an MNI (non-maskable
interface) button and a power on/off button.

! RESET: Use the reset button to reboot the system.

! NMI: NMI stands for "non-maskable interrupt". Pressing this button

issues a non-maskable interrupt to force the server into a halt state. This is
used for diagnostic purposes, and allows you to perform a memory down­load to determine the cause of a problem.

SUPERSERVER 6013P-8 User's Manual

3-2

! POWER: This is the main power button, which is used to apply or turn
off the main system power. Turning off system power with this button
removes the main power but keeps standby power supplied to the system.

3-3 Control Panel LEDs

The control panel located on the front of the SC812S-400 chassis has five LEDs.
These LEDs provide you with critical information related to different parts of the
system. This section explains what each LED indicates when illuminated and
any corrective action you may need to take.

! Overheat: Indicates an overheat condition in the chassis. This may be
caused by cables obstructing the airflow in the system or the ambient room
temperature being too warm. You should also check to make sure that the
chassis cover is installed and that all fans are present and operating normally.
Verify that the heatsinks are installed properly (see Chapter 5). Finally, check
the air seals for damage. The air seals are vertical pieces located to the left and
right of the fans and against the front side of the chassis frame cross section that
separates the drive bay area from the serverboard area of the chassis. There is
also a small air seal positioned between the two fans.

! NIC2: Indicates network activity on LAN2 when flashing.

NIC2