Supermicro SuperServer 1025C-3 User Manual

SUPER

SUPERSERVER 1025C-3

®

USER’S MANUAL

Revision 1.0

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
makes no commitment to update or to keep current the information in this manual, or to notify any
person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software, if any,
and documentation may not, in whole or in part, be copied, photocopied, reproduced, translated or
reduced to any medium or machine without prior written consent.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO
USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY
HARDWARE, SOFTW ARE, OR DA TA STORED OR USED WITH THE PRODUCT, INCLUDING THE
COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH
HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa
Clara County in the State of California, USA. The State of California, County of Santa Clara shall
be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for
all claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.

Manual Revision 1.0
Release Date: November 6, 2008

Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.

Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2008 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It
provides information for the installation and use of the SuperServer 1025C-3. Instal­lation and maintenance should be performed by experienced technicians only.

The SuperServer 1025C-3 is a high-end dual processor rackmount server based on
the SC111TQ-560CB 1U server chassis and the Super X7DCL-3 serverboard.

Manual Organization

Preface

Chapter 1: Introduction

The fi rst chapter provides a checklist of the main components included with the
server system and describes the main features of the Super X7DCL-3 serverboard
and the SC111TQ-560CB chassis.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer 1025C-3 into
a rack and check out the server confi guration prior to powering up the system. If your
server was ordered without the processor and memory components, this chapter will
refer you to the appropriate sections of the manual for their installation.

Chapter 3: System Interface

Refer to this chapter for details on the system interface, which includes the functions
and information provided by the control panel on the chassis as well as other LEDs
located throughout the system.

Chapter 4: System Safety

You should thoroughly familiarize yourself with this chapter for a general overview
of safety precautions that should be followed when installing and servicing the
SuperServer 1025C-3.

iii

SUPERSERVER 1025C-3 User's Manual

Chapter 5: Advanced Serverboard Setup

Chapter 5 provides detailed information on the X7DCL-3 serverboard, including the
locations and functions of connectors, headers and jumpers. Refer to this chapter
when adding or removing processors or main memory and when reconfi guring the
serverboard.

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the SC111TQ-560CB 1U rackmount
server chassis. You should follow the procedures given in this chapter when install­ing, removing or reconfi guring hot-swap or peripheral drives and when replacing
system power supply and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed informa­tion on running the CMOS Setup Utility.

Appendix A: BIOS POST Messages

Appendix B: BIOS POST Codes

Appendix C: System Specifi cations

iv

Notes

Preface

v

SUPERSERVER 1025C-3 User's Manual

Table of Contents

Chapter 1 Introduction

1-1 Overview .........................................................................................................1-1

1-2 Serverboard Features .....................................................................................1-2

Processors ......................................................................................................1-2

Memory ...........................................................................................................1-2

Onboard SAS .................................................................................................. 1-2

Serial ATA ........................................................................................................ 1-2

PCI Expansion Slots ....................................................................................... 1-2

Ethernet Ports .................................................................................................1-3

Onboard Controllers/Ports .............................................................................. 1-3

Other Features ................................................................................................ 1-3

1-3 Server Chassis Features ................................................................................ 1-5

System Power ................................................................................................. 1-5

Control Panel .................................................................................................. 1-5

I/O Backplane .................................................................................................. 1-5

Cooling System ............................................................................................... 1-5

1-4 Contacting Supermicro ....................................................................................1-6

Chapter 2 Server Installation

2-1 Overview .........................................................................................................2-1

2-2 Unpacking the System .................................................................................... 2-1

2-3 Preparing for Setup .........................................................................................2-1

Choosing a Setup Location ............................................................................. 2-1

Rack Precautions ............................................................................................ 2-2

Server Precautions .......................................................................................... 2-2

Rack Mounting Considerations ....................................................................... 2-3

Ambient Operating Temperature ................................................................ 2-3

Reduced Airfl ow .........................................................................................2-3

Mechanical Loading ................................................................................... 2-3

Circuit Overloading .....................................................................................2-3

Reliable Ground ......................................................................................... 2-3

2-4 Installing the System into a Rack ................................................................... 2-4

Identifying the Sections of the Rack Rails ......................................................2-4

Inner Rails ....................................................................................................... 2-5

Outer Rails ......................................................................................................2-6

Installing the Server into a Telco Rack ........................................................... 2-9

2-5 Checking the Serverboard Setup .................................................................... 2-9

vi

Table of Contents

2-6 Checking the Drive Bay Setup ...................................................................... 2-10

Chapter 3 System Interface

3-1 Overview .........................................................................................................3-1

3-2 Control Panel Buttons ..................................................................................... 3-1

Reset ...............................................................................................................3-1

Power ..............................................................................................................3-1

UID ..................................................................................................................3-1

3-3 Control Panel LEDs ........................................................................................3-2

Universal Information LED .............................................................................. 3-2

NIC2 ................................................................................................................3-3

NIC1 ................................................................................................................3-3

HDD .................................................................................................................3-3

Power ..............................................................................................................3-3

3-4 Hard Drive Carrier LEDs .................................................................................3-4

Chapter 4 System Safety

4-1 Electrical Safety Precautions .......................................................................... 4-1

4-2 General Safety Precautions ............................................................................ 4-2

4-3 ESD Precautions ............................................................................................. 4-3

4-4 Operating Precautions .................................................................................... 4-4

Chapter 5 Advanced Serverboard Setup

5-1 Handling the Serverboard ............................................................................... 5-1

Precautions .....................................................................................................5-1

Unpacking .......................................................................................................5-2

5-2 Serverboard Installation ..................................................................................5-2

5-3 Connecting Cables .......................................................................................... 5-3

Connecting Data Cables ................................................................................. 5-3

Connecting Power Cables .............................................................................. 5-3

Connecting the Control Panel .........................................................................5-4

5-4 I/O Ports .......................................................................................................... 5-4

5-5 Processor and Heatsink Installation................................................................5-5

5-6 Installing Memory ............................................................................................5-8

5-7 Adding PCI Cards ........................................................................................... 5-9

5-8 Serverboard Details ...................................................................................... 5-10

Motherboard Layout ...................................................................................... 5-10

X7DCL-3 Quick Reference.............................................................................5-11

5-9 Connector Defi nitions ...................................................................................5-12

ATX Power Connector ..............................................................................5-12

Processor Power Connector ................................................................... 5-12

vii

SUPERSERVER 1025C-3 User's Manual

PW_ON Connector ................................................................................... 5-12

Reset Connector ...................................................................................... 5-12

Overheat LED (OH) .................................................................................. 5-13

NIC2 (LAN2) LED ..................................................................................... 5-13

NIC1 (LAN1) LED ..................................................................................... 5-13

HDD LED .................................................................................................. 5-13

Power On LED .........................................................................................5-13

NMI Button ............................................................................................... 5-14

Fan Headers ............................................................................................. 5-14

ATX PS/2 Keyboard and PS/2 Mouse Ports ............................................ 5-14

Chassis Intrusion ......................................................................................5-14

LAN1/2 (Ethernet Ports) ...........................................................................5-14

Universal Serial Bus (USB) ......................................................................5-15

Wake-On-LAN ..........................................................................................5-15

Wake-On-Ring ..........................................................................................5-15

Power Supply Fail Detect ......................................................................... 5-16

Alarm Reset .............................................................................................. 5-16

PWR I
BPI

2

C ...................................................................................................5-16

2

C ........................................................................................................5-16

Serial Ports ...............................................................................................5-17

SGPIO Headers ....................................................................................... 5-17

Power LED/Speaker .................................................................................5-17

Keylock .....................................................................................................5-17

5-10 Jumper Settings ............................................................................................5-18

Explanation of Jumpers ................................................................................ 5-18

CMOS Clear ............................................................................................. 5-18

VGA Enable/Disable ................................................................................. 5-18

LAN1/LAN2 Enable/Disable ..................................................................... 5-19

SAS Enable/Disable ................................................................................. 5-19

SAS RAID Select ..................................................................................... 5-19

Watch Dog ................................................................................................ 5-19

2

I

C Bus to PCI/PCI-Exp. Slots .................................................................5-20

5-11 Onboard Indicators ........................................................................................5-20

LAN1/LAN2 LEDs ..................................................................................... 5-20

Onboard Power LED (LED3)....................................................................5-20

System Status LED (LED4)......................................................................5-20

CPU_VRM Overheat LED Indicators (LED5/LED6) ................................. 5-21

5-12 Floppy and IDE Drive Connections...............................................................5-21

Floppy Connector ..................................................................................... 5-21

viii

Table of Contents

IDE Connector ..........................................................................................5-22

SAS Ports .................................................................................................5-23

SATA Ports ...............................................................................................5-23

5-13 Installing Software .........................................................................................5-24

Supero Doctor III ...........................................................................................5-25

Chapter 6 Advanced Chassis Setup

6-1 Static-Sensitive Devices ..................................................................................6-1

Precautions .....................................................................................................6-1

6-2 Control Panel ..................................................................................................6-2

6-3 System Cooling ...............................................................................................6-2

System Fan Failure .........................................................................................6-3

6-4 Drive Bay Installation/Removal ....................................................................... 6-4

Accessing the Drive Bays ............................................................................... 6-4

Hard Drive Installation ..................................................................................... 6-4

DVD Drive Installation .....................................................................................6-6

6-5 Power Supply ..................................................................................................6-7

Power Supply Failure ......................................................................................6-7

Replacing the Power Supply ........................................................................... 6-8

Chapter 7 BIOS

7-1 Introduction ......................................................................................................7-1

7-2 Running Setup ................................................................................................ 7-2

7-3 Main BIOS Setup ............................................................................................ 7-2

7-4 Advanced Setup .............................................................................................. 7-7

7-5 Security .........................................................................................................7-20

7-6 Boot ............................................................................................................... 7-21

7-7 Exit ................................................................................................................7-22

Appendix A BIOS POST Messages
Appendix B BIOS POST Codes
Appendix C System Specifi cations

ix

SUPERSERVER 1025C-3 User's Manual

Notes

x

Chapter 1: Introduction

Chapter 1

Introduction

1-1 Overview

The SuperServer 1025C-3 is a dual processor server comprised of two main subsys­tems: the SC111TQ-560CB 1U rackmount chassis and the X7DCL-3 serverboard.
Please refer to our web site for information on operating systems that have been
certifi ed for use with the 1025C-3 (www.supermicro.com).

In addition to the serverboard and chassis, various hardware components may have
been included with the 1025C-3, as listed below.

Two (2) CPU heatsinks (SNK-P0017)

•

One (1) slim DVD-ROM drive (DVM-PNSC-824B)•

SAS/SATA Accessories: •
Four (4) SAS/SATA 2.5" hard drive carriers (MCP-220-00047-0B)
One (1) internal SAS/SATA backplane (BPN-SAS-809TQ)
Four (4) SAS/SATA cables (CBL-0061L)

One (1) SGPIO cable (CBL-0157L)

•

One (1) PCI-E x8 riser card (CSE-RR1U-E8)•

Three (3) counter-rotating fans (FAN-0085L4) •

Rackmount hardware with screws (CSE-PT51L)•

One (1) CD containing drivers and utilities •

SuperServer 1025C-3 User's Manual•

Note: "B" indicates part is available in black.

1-1

SUPERSERVER 1025C-3 User's Manual

1-2 Serverboard Features

At the heart of the SuperServer 1025C-3 lies the X7DCL-3, a single processor
serverboard based on Intel's 5100 chipset and designed to provide maximum per­formance. Below are the main features of the X7DCL-3.

Processors

The X7DCL-3 supports dual Intel® 5400, 5300, 5200 or 5100 Series processors in
LGA771 sockets. Please refer to our web site for a complete listing of supported
processors (www.supermicro.com).

Memory

The X7DCL-3 has six 240-pin DIMM sockets that can support up to 48 GB of reg­istered ECC DDR2-667/533 SDRAM. Memory must be installed in an interleaved
(dual-channel) confi guration. All memory modules used to populate the system
should be the same size, type and speed. See Chapter 5 for details.

Onboard SAS

An onboard LSI 1068E SAS controller in integrated into the X7DCL-3. The 2.5"
hot-swap SAS drives are connected to a backplane that provides power and con­fi guration settings.

Note: The operati ng system yo u use must h ave R AID su ppor t to e nable t he hot­swap cap abilit y and RAID funct ion of t he SAS dr ives . R AID 0, 1, 5 (with op tion al
I- but ton) and 10 are supp orted. Refer to the follow ing ftp site for setup gui deli nes
<ftp://ftp.supermicro.com/driver/SAS/LSI/LSI _ SAS_EmbMRAID_ SWUG.pdf >.

Serial ATA

The Sout h Bridge (ICH 9R) of the 5100 chipset includes a Serial ATA controller
that supp or ts six S ATA po rt s .

PCI Expansion Slots

The X7DCL-3 has two PCI-Express x8 slots, one PCI-Express x4 slot (in a x8 slot)
and three 32-bit, 33 MHz (5V) PCI slots. In the 1025C-3 server confi guration, a
PCI-E riser card (CSE-RR1U-E8) has been installed to support a single PCI-Ex­press add-on card.

1-2

Chapter 1: Introduction

Ethernet Ports

The X7DCL-3 has two network controllers integrated into the chipset to support two
Gigabit LAN ports (100/1000Base-T/1000BaseTX, RJ45 output).

Onboard Controllers/Ports

An onboard IDE controller supports Ultra ATA 100 hard drives or ATAPI devices.
Onboard I/O backpanel ports include one COM port, a VGA port, two USB ports,
PS/2 mouse and keyboard ports and two Gigabit LAN (NIC) ports.

Other Features

Other onboard features that promote system health include voltage monitors, a
chassis intrusion header, auto-switching voltage regulators, chassis and CPU
overheat sensors, virus protection and BIOS rescue.

1-3

SUPERSERVER 1025C-3 User's Manual

MCH

PROCESSOR#1

1067/1333

MT/S

#0-2

#0-1

#0-3

ISL6312A

PCI-EXP x8

PCI-E x8

PROCESSOR#2

1067/1333

MT/S

PORT

#2,3

Intel 5100

#7

#6

#5

#4

#3

#2

#1

#0

3.0 Gb/S

SAS

RJ45

RJ45

GDDR2 SDRAM 32MB

VGA
CONN

LSI 1068E

82573V

82573V

VGA

Volari Z9S

IDE

IT8213F

PCI-33

PCI-33

PCI-33

PCI-EXP x8

PCI-E x8

PCI-EXP x8

PCI-EXP x1

PCI-EXP x1

PCI-E x8 Slot

PCI-E x4Signal

PCI 33MHz

PORT

#4,5

PORT

#6,7

LANE5

LANE6

LANE1/2/3/4

PORT

#0

PCIE X4

DMI

ICH9R

LPC

SIO

W83627HG

MS

KB

COM1

External

DDR2 667

3.0 Gb/S

FWH

#1-3

#1-2

#1-1

DDR2 667

#1

#0

#1

#0

USB 2.0

COM2

INTERNAL/SOL

ISL6312A

#5

#4

#3

#2

SATA

#6

#5

#4

#3

#2

USB

Note: This is a general block diagram. Please see Chapter 5 for details.

Figure 1-1 . Intel 5100 Chipset:

System Block Diagram

1-4

Chapter 1: Introduction

1-3 Server Chassis Features

The SC1 1 1TQ-560CB is a cost-effective 1U chassis that features four 2.5" hard drive
bays and a 560W high-effi ciency power supply. The following is a general outline
of the main features of the SC111TQ-560CB chassis.

System Power

When confi gured as a SuperServer 1025C-3, the SC1 1 1TQ-560CB chassis includes
a single 560W power supply. This is a high-effi ciency power supply that operates
at 80% effi ciency or better.

Control Panel

The control panel on the SC111TQ-560CB provides important system monitoring
and control information. LEDs indicate power on, network activity, hard disk drive
activity and a UID (Universal Information) LED. Also present are a main power
button, a system reset button and a UID button.

Note: The UID button is not functional on the 1025C-3.

I/O Backplane

The SC111TQ-560CB is a 1U rackmount chassis. Its I/O backplane provides three
PCI slots, one COM port (the other is internal), one VGA port, two USB ports, PS/2
mouse and keyboard ports, two Ethernet (LAN) ports and a UID LED.

Cooling System

The SC111TQ-560CB chassis' revolutionary cooling design has been optimized to
provide suffi cient cooling for dual CPU confi gurations. The chassis includes three
4-cm counter-rotating PWM (Pulse Width Modulated) fans located in the middle of
the chassis. T wo optional high-performance 4-cm fans may also be added to supply
increased airfl ow to the add-on card section. There is a "Fan Speed Control Mode"
in BIOS that allows chassis fan speed to be determined by system temperature.

1-5

SUPERSERVER 1025C-3 User's Manual

1-4 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.
San Jose, CA 95131 U.S.A.

Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML
's-Hertogenbosch, The Netherlands

Tel: [phone]
Fax: [phone]
Email: [e-mail] (General Information)

[e-mail] (Technical Support)
[e-mail] (Customer Support)

Asia-Pacifi c

Address: Super Micro Computer, Inc.

4F, No. 232-1, Liancheng Rd.
Chung-Ho 235, Taipei County
Taiwan, R.O.C.

Tel: [phone]
Fax: [phone]
Web Site: www.supermicro.com.tw
Technical Support:
Email: [e-mail]
Tel: [phone], ext.132 or 139

1-6

Chapter 2: Server Installation

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your SuperServer 1025C-3
up and running. Following these steps in the order given should enable you to
have the system operational within a minimum amount of time. This quick setup
assumes that your SuperServer 1025C-3 system has come to you with the proces­sors and memory preinstalled. If your system is not already fully integrated with a
serverboard, processors, system memory etc., please turn to the chapter or section
noted in each step for details on installing specifi c components.

2-2 Unpacking the System

You should inspect the box the SuperServer 1025C-3 was shipped in and note if
it was damaged in any way. If the server itself shows damage you should fi le a
damage claim with the carrier who delivered it.

Decide on a suitable location for the rack unit that will hold the SuperServer
1025C-3. It should be situated in a clean, dust-free area that is well ventilated. A void
areas where heat, electrical noise and electromagnetic fi elds are generated. You
will also need it placed near a grounded power outlet. Read the Rack and Server
Precautions in the next section.

2-3 Preparing for Setup

The box the SuperServer 1025C-3 was shipped in should include two sets of rail
assemblies, two rail mounting brackets and the mounting screws you will need to
install the system into the rack. Follow the steps in the order given to complete
the installation process in a minimum amount of time. Please read this section in
its entirety before you begin the installation procedure outlined in the sections that
follow.

Choosing a Setup Location

Leave enough clearance in front of the rack to enable you to open the front door •
completely (~25 inches) and approximately 30 inches of clearance in the back
of the rack to allow for suffi cient airfl ow and ease in servicing.This product is for

2-1

SUPERSERVER 1025C-3 Manual

!

!

installation only in a Restricted Access Location (dedicated equipment rooms,
service closets and the like).

This product is not suitable for use with visual display work place devices

•

acccording to §2 of the the German Ordinance for Work with Visual Display
Units.

Warnings and Precautions!

Rack Precautions

Ensure that the leveling jacks on the bottom of the rack are fully extended to •
the fl oor with the full weight of the rack resting on them.

In single rack installation, stabilizers should be attached to the rack. In multiple

•

rack installations, the racks should be coupled together.

Always make sure the rack is stable before extending a component from the

•

rack.

You should extend only one component at a time - extending two or more si-

•

multaneously may cause the rack to become unstable.

Server Precautions

Review the electrical and general safety precautions in Chapter 4.•

Determine the placement of each component in the rack • before you install the
rails.

Install the heaviest server components on the bottom of the rack fi rst, and then

•

work up.

Use a regulating uninterruptible power supply (UPS) to protect the server from

•

power surges, voltage spikes and to keep your system operating in case of a
power failure.

Allow the hot plug SATA drives and power supply modules to cool before touch-

•

ing them.

Always keep the rack's front door and all panels and components on the servers

•

closed when not servicing to maintain proper cooling.

2-2

Chapter 2: Server Installation

Rack Mounting Considerations

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating tempera­ture of the rack environment may be greater than the ambient temperature of the
room. Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient tempera­ture (Tmra).

Reduced Airfl ow

Equipment should be mounted into a rack so that the amount of airfl ow required
for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition does not
arise due to uneven mechanical loading.

Circuit Overloading

Consideration should be given to the connection of the equipment to the power
supply circuitry and the effect that any possible overloading of circuits might have
on overcurrent protection and power supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack itself
should be grounded. Particular attention should be given to power supply connec­tions other than the direct connections to the branch circuit (i.e. the use of power
strips, etc.).

2-3

SUPERSERVER 1025C-3 Manual

2-4 Installing the System into a Rack

This section provides information on installing the SuperServer 1025C-3 into a rack.
If the 1025C-3 has already been mounted into a rack, you can skip ahead to Sections
2-5 and 2-6. Note: The rails will fi t a rack between 26" and 33.5" deep.

There are a variety of rack units on the market, which may mean the assembly
procedure will differ slightly. The following is a guideline for installing the 1025C-3
into a rack with the rack rails provided. You should also refer to the installation
instructions that came with the rack unit you are using.

Identifying the Sections of the Rack Rails

Each assembly consists of two sections: an inner fi xed chassis rail that secures
directly to the server chassis and an outer fi xed rack rail that secures directly to
the rack itself.

Figure 2-1. Identifying the Sections of the Rack Rails

Inner Rail Extensions

Inner Rails

(preinstalled)

2-4

Chapter 2: Server Installation

Inner Rails

The SC11 1 chassis includes a set of inner rails in two sections: inner rails and inner
rail extensions. The inner rails are pre-attached and do not interfere with normal
use if you decide not to mount the system into a server rack. Attach the inner rail
extension to stabilize the chassis within the rack.

Installing the Inner Rails (Figure 2-2)

Place the inner rack extensions on the side of the chassis aligning the hooks 1.
of the chassis with the rail extension holes. Make sure the extension faces
"outward" just like the pre-attached inner rail.

Slide the extension toward the front of the chassis.2.

Secure the chassis with two screws as illustrated.3.

Repeat steps 1-3 for the other inner rail extension.4.

Figure 2-2. Installing Chassis Rails

1

3

1

3

1

1

1

2

1

1

2

1

2-5

SUPERSERVER 1025C-3 Manual

Outer Rails

Installing the Outer Rails to the Rack (Figures 2-3 and 2-4)

Attach the short bracket to the outside of the long bracket. You must align the 1.
pins with the slides. Also, both bracket ends must face the same direction.

Adjust both the short and long brackets to the proper distance so that the rail 2.
fi ts snugly into the rack.

Secure the long bracket to the front side of the outer rail with two M5 screws 3.
and the short bracket to the rear side of the outer rail with three M5 screws.

Repeat steps 1-4 for the left outer rail.4.

Secure to the

Front of the Rack

Figure 2-3. Assembling the Outer Rails

Attach Outer Rails

Together

Secure to the

Rear of the Rack

2-6

Chapter 2: Server Installation

3

3

2

Figure 2-4. Installing the Outer Rails to the Rack

2-7

SUPERSERVER 1025C-3 Manual

Installing the Chassis into a Rack (Figure 2-5)

Confi rm that chassis includes the inner rails and rail extensions . Also, confi rm 1.
that the outer rails are installed on the rack.

Line chassis rails with the front of the rack rails.2.

Slide the chassis rails into the rack rails, keeping the pressure even on both 3.
sides (you may have to depress the locking tabs when inserting). When the
server has been pushed completely into the rack, you should hear the locking
tabs "click".

(Optional) Insert and tightening the thumbscrews that hold the front of the 4.
server to the rack.

Figure 2-5. Installing the Server into a Rack

2-8

Chapter 2: Server Installation

Installing the Server into a Telco Rack

To install the SuperServer 1025C-3 into a Telco type rack, use two L-shaped brack­ets on either side of the chassis (four total). First, determine how far follow the
server will extend out the front of the rack. Larger chassis should be positioned to
balance the weight between front and back. If a bezel is included on your server,
remove it. Then attach the two front brackets to each side of the chassis, then the
two rear brackets positioned with just enough space to accommodate the width of
the telco rack. Finish by sliding the chassis into the rack and tightening the brackets
to the rack.

2-5 Checking the Serverboard Setup

After you install the 1025C-3 in the rack, you will need to open the unit to make sure
the serverboard is properly installed and all the connections have been made.

Removing the Chassis Cover (Figure 2-6)

Grasp the two handles on either side and pull the unit straight out until it 1.
locks (you will hear a "click").

Remove the thumbscrew securing the top cover to the chassis.2.

Slide the cover toward the rear of the chassis.3.

Lift the cover off the chassis.4.

Checking the Components

You should have one or two processors already installed into the serverboard. 1.
Each processor needs its own heatsink. See Chapter 5 for instructions on
processor and heatsink installation.

Your 1025C-3 server system may have come with system memory already 2.
installed. Make sure all DIMMs are fully seated in their slots. For details on
adding system memory, refer to Chapter 5.

If desired, you can install add-on cards to the system. See Chapter 5 for 3.
details on installing PCI add-on cards.

Make sure all power and data cables are properly connected and not block-4.
ing the chassis airfl ow. See Chapter 5 for details on cable connections. Also,
check the air seals for damage. The air seals are located under the blower

2-9

SUPERSERVER 1025C-3 Manual

fan and beneath the frame cross section that separates the drive bay area
from the serverboard area of the chassis.

2-6 Checking the Drive Bay Setup

Next, you should check to make sure the hard drives have been properly installed
and all connections have been made.

Checking the Drives

Hard drives can be serviced without removing the top chassis cover.1.

If you need to remove or install hard drives, please refer to Chapter 6.2.

Checking the Airfl ow

Airfl ow is provided by three 4-cm fans. The system component layout was 1.
carefully designed to direct suffi cient cooling airfl ow to the components that
generate the most heat.

Note that all power and data cables have been routed in such a way that they 2.
do not block the airfl ow generated by the fans.

Providing Power

The last thing you must do is to provide input power to the system. Plug the 1.
power cord from the power supply unit into a high-quality power strip that of­fers protection from electrical noise and power surges. It is recommended that
you use an uninterruptible power supply (UPS).

Finish by depressing the power button on the chassis control panel.2.

2-10

Chapter 2: Server Installation

Figure 2-6: Removing the Chassis Cover

4

1

3

1

2-11

SUPERSERVER 1025C-3 Manual

Notes

2-12

Chapter 3: System Interface

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the control panel to keep you constantly informed of the
overall status of the system as well as the three buttons described below.

3-2 Control Panel Buttons

There are three buttons located on the front of the chassis: a reset button, a power
on/off button and a UID button.

Reset

Use the reset button to reboot the system.

Power

This is the main power button, which is used to apply or turn off the main system
power. T urning off system power with this button removes the main power but keeps
standby power supplied to the system.

UID

A UID (unit identifi er) button is included on the chassis, however it is not functional
on the 1025C-3.

3-1

SUPERSERVER 1025C-3 Manual

3-3 Control Panel LEDs

The control panel located on the front of the SC111TQ-560CB chassis has fi ve
LEDs. These LEDs provide you with critical information related to different parts of
the system. This section explains what each LED indicates when illuminated and
any corrective action you may need to take.

Universal Information LED

When this LED blinks red quickly, it indicates a fan failure and when blinking red
slowly a power failure. When on continuously this LED indicates an overheat condi­tion, which may be caused by cables obstructing the airfl ow in the system or the
ambient room temperature being too warm. Check the routing of the cables and
make sure all fans are present and operating normally. You should also check to
make sure that the chassis covers are installed. Finally , verify that the heatsinks are
installed properly (see Chapter 5). This LED will remain fl ashing or on as long as the
indicated condition exists. See the table below for descriptions of the LED states.

Figure 3-1. Universal Information LED States

Universal Information LED States

State Indication
Fast Blinking Red (1x/sec) Fan Fail
Solid Red CPU Overheat
Slow Blinking Red (1x/4 sec) Power Fail

Note: deactivating the UID LED must be performed in the same way it was acti­vated.

3-2