Supermicro SUPERO X10DRU-X, SUPERO X10DRU-XLL User Manual

USER’S MANUAL

Revision 1.0c

X10DRU-X

X10DRU-XLL

Manual Revision 1.0c

Release Date: February 5, 2015

Unless you request and receive written permission from Super Micro Computer, Inc., you may not
copy any part of this document.

Information in this document is subject to change without notice. Other products and companies
referred to herein are trademarks or registered trademarks of their respective companies or mark
holders.

Copyright © 2015 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

The information in this user’s manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
and makes no commitment to update or to keep current the information in this manual, or to notify
any person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our website at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu­mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.

IN NO EVENT WILL SUPER MICRO COMPUTER, INC. BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE
USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC.
SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED
WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between the manufacturer and the customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of Santa Clara
shall be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for
all claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”.

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.

Preface

This manual is written for system integrators, IT professionals, and

knowledgeable end users. It provides information for the installation and use of the

X10DRU-X/X10DRU-XLL motherboard.

About This Motherboard

The Super X10DRU-X/X10DRU-XLL motherboard supports dual Intel® E5-2600V3

Series Processors (Socket R3) that offer QPI (Intel QuickPath Interface) Technology,

providing point-to-point connection with a transfer speed of up to 9.6 GT/s. With

the PCH C612 built in, the X10DRU-X/X10DRU-XLL motherboard supports Intel®

Manageability Engine, Rapid Storage Technology, Digital Media Interface (DMI),

PCI-E Gen. 3.0, and 2133 MHz DDR4 memory. This motherboard is sold only as a

system within the Hyper-Speed Ultra server platforms. Please refer to our website

(http://www.supermicro.com) for processor and memory support updates.

Manual Organization

Chapter 1 describes the features, specications and performance of the mother-

board. It also provides detailed information about the Intel® PCH C612 chipset.

Chapter 2 provides hardware installation instructions. Read this chapter when in-

stalling the processor, memory modules, and other hardware components into the

system. If you encounter any problems, see Chapter 3, which describes trouble-

shooting procedures for video, memory, and system setup stored in CMOS.

Chapter 4 includes an introduction to BIOS, and provides detailed information on

running the CMOS Setup utility.

Appendix A provides BIOS Error Beep Codes.

Appendix B lists software installation instructions.

Preface

iii

iv

Conventions Used in the Manual

Pay special attention to the following symbols for proper system installation and to

prevent damage to the system or injury to yourself:

Warning: Important information given to ensure proper system installation or to prevent

damage to the components

Note: Additional information given to differentiate between various models

or provides information for proper system setup.

X10DRU-X/X10DRU-XLL Motherboard User’s Manual

Preface

v

Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Web Site: www.supermicro.nl

Asia-Pacic

Address: Super Micro Computer, Inc.

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 235

Taiwan (R.O.C)

Tel: [phone]

Fax: [phone]

Email: [e-mail]

Web Site: www.supermicro.com.tw

vi

Table of Contents

Preface

About This Motherboard ................................................................................................ 3

Manual Organization ..................................................................................................... 3

Conventions Used in the Manual .................................................................................. 4

Contacting Supermicro .................................................................................................. 5

Chapter 1 Overview

1-1 Overview ......................................................................................................... 1-1

Checklist .......................................................................................................... 1-1

X10DRU-X(LL) Motherboard Quick Reference ............................................... 1-4

Motherboard Features ..................................................................................... 1-7

1-2 Processor and Chipset Overview .................................................................1-11

1-3 Special Features ........................................................................................... 1-12

Recovery from AC Power Loss ..................................................................... 1-12

1-4 System Health Monitoring ............................................................................. 1-12

Fan Status Monitor with Firmware Control .................................................. 1-12

Environmental Temperature Control ............................................................. 1-12

System Resource Alert ................................................................................. 1-12

1-5 ACPI Features ............................................................................................... 1-13

1-6 Power Supply ................................................................................................ 1-13

1-7 Serial Port ..................................................................................................... 1-13

1-8 Advanced Power Management ..................................................................... 1-13

Intel® Intelligent Power Node Manager (NM) (Available when the NMView

software is installed) ..................................................................................... 1-13

Management Engine (ME) ............................................................................ 1-14

Chapter 2 Installation

2-1 Standardized Warning Statements ................................................................. 2-1

Battery Handling .............................................................................................. 2-1

Product Disposal ............................................................................................. 2-3

2-2 Static-Sensitive Devices .................................................................................. 2-4

Precautions ..................................................................................................... 2-4

Unpacking ....................................................................................................... 2-4

2-3 Motherboard Installation .................................................................................. 2-5

Tools Needed .................................................................................................. 2-5

Location of Mounting Holes ............................................................................ 2-5

Installing the Motherboard .............................................................................. 2-6

2-4 Processor and Heatsink Installation................................................................ 2-7

X10DRU-X/X10DRU-XLL Motherboard User’s Manual

vii

Table of Contents

Installing the LGA2011 Processor ................................................................. 2-7

Installing a Passive CPU Heatsink ................................................................2-11

Removing the Passive Heatsink ................................................................... 2-12

2-5 Installing and Removing the Memory Modules ............................................. 2-13

Installing & Removing DIMMs ....................................................................... 2-13

Removing Memory Modules ......................................................................... 2-13

2-6 Control Panel Connectors and I/O Ports ...................................................... 2-16

Back Panel Connectors and I/O Ports .......................................................... 2-16

Back Panel I/O Port Locations and Denitions ........................................... 2-16

Universal Serial Bus (USB) ...................................................................... 2-17

LAN Port ................................................................................................... 2-18

COM1 ....................................................................................................... 2-19

Video Connector ....................................................................................... 2-19

Unit Identier Switch ................................................................................ 2-20

Front Panel Accessible Add-on Card Connector (JF1) ................................. 2-21

2-7 Connecting Cables ........................................................................................ 2-22

IPMB I2C SMB .......................................................................................... 2-22

DOM Power Connectors .......................................................................... 2-22

GPU/VGA Power Connectors................................................................... 2-23

IPMB ......................................................................................................... 2-23

Fan Headers ............................................................................................. 2-24

TPM Header/Port 80 ................................................................................ 2-25

Chassis Intrusion (JL1) ............................................................................ 2-25

I-SGPIO Header ....................................................................................... 2-26

2-8 Jumper Settings ............................................................................................ 2-27

Explanation of Jumpers ................................................................................ 2-27

Manufacturing Mode Select ..................................................................... 2-27

Clear CMOS ............................................................................................. 2-28

Watch Dog Enable/Disable ...................................................................... 2-28

VGA Enable .............................................................................................. 2-29

BMC Enable ............................................................................................. 2-29

Internal Buzzer ......................................................................................... 2-30

I2C Bus for VRM ....................................................................................... 2-30

2-9 Onboard LED Indicators ............................................................................... 2-31

IPMI Dedicated LAN LEDs ....................................................................... 2-31

BMC Heartbeat LED ................................................................................ 2-32

Hard Disk Activity LED ............................................................................. 2-32

Power LED ............................................................................................... 2-33

2-10 PCI-E 3.0 Slots and SATA ............................................................................ 2-34

viii

PCI-Express 3.0 Slots .............................................................................. 2-34

SATA Ports ............................................................................................... 2-34

Chapter 3 Troubleshooting

3-1 Troubleshooting Procedures ........................................................................... 3-1

Before Power On ............................................................................................ 3-1

No Power ........................................................................................................ 3-1

No Video ......................................................................................................... 3-2

System Boot Failure ........................................................................................ 3-2

Losing the System’s Setup Conguration ....................................................... 3-2

Memory Errors ............................................................................................... 3-3

When the System Becomes Unstable ............................................................ 3-3

3-2 Technical Support Procedures ........................................................................ 3-5

Proper Battery Disposal .................................................................................. 3-6

Battery Installation ........................................................................................... 3-6

3-3 Battery Removal and Installation .................................................................... 3-6

Battery Removal .............................................................................................. 3-6

3-4 Frequently Asked Questions ........................................................................... 3-7

3-5 Returning Merchandise for Service................................................................. 3-8

Chapter 4 BIOS

4-1 Introduction ...................................................................................................... 4-1

Starting BIOS Setup Utility .............................................................................. 4-1

How To Change the Conguration Data ......................................................... 4-2

Starting the Setup Utility ................................................................................. 4-2

4-2 Main Setup ...................................................................................................... 4-2

4-3 Advanced Setup Congurations...................................................................... 4-4

4-4 Event Logs .................................................................................................... 4-32

4-5 IPMI ............................................................................................................... 4-34

4-6 Security Settings ........................................................................................... 4-36

4-7 Boot Settings ................................................................................................. 4-37

4-8 Save & Exit ................................................................................................... 4-39

Appendix A BIOS Error Beep Codes

A-1 BIOS Error Beep Codes .................................................................................A-1

Appendix B Software Installation Instructions

B-1 Installing Software Programs ..........................................................................B-1

B-2 Conguring SuperDoctor® 5 ........................................................................... B-2

X10DRU-X/X10DRU-XLL Motherboard User’s Manual

Chapter 1: Overview

1-1

Chapter 1

Overview

1-1 Overview

Checklist

Congratulations on purchasing your computer motherboard from an acknowledged

leader in the industry. Supermicro boards are designed with the utmost attention to

detail to provide you with the highest standards in quality and performance.

This motherboard is sold only as a system within the Hyper-Speed Ultra server

platforms. Please refer to our website at http://www.supermicro.com for information

on Hyper-Speed Ultra server products.

For your system to work properly, please follow the links below to download all

necessary drivers/utilities and the user's manual for your motherboard.

Supermicro product manuals: http://www.supermicro.com/support/manuals/

Product Drivers and utilities: ftp://ftp.supermicro.com/

If you have any questions, please contact our support team at support@supermicro.

com.

1-2

X10DRU-X/X10DRU-XLL Motherboard User’s Manual

Note: All graphics shown in this manual were based upon the latest PCB

Revision available at the time of publishing of the manual. The motherboard

you've received may or may not look exactly the same as the graphics

shown in this manual.

Motherboard Image

Chapter 1: Overview

1-3

Notes:

1. For the latest CPU/Memory updates, please refer to our website at http://

www.supermicro.com/products/motherboard/ for details.

2. Use only the correct type of onboard CMOS battery as specied by

the manufacturer. Do not install the onboard battery upside down to avoid

possible explosion.

Motherboard Layout

X10DRU-X

REV:1.01

I-SGPIO2

JF1

JL1

DESIGNED IN USA

JUSBA1

JBAT1

JBT1

JSD2

JSD1

SP1

LED_H1

LED_G2

LED_G1

LED_H2

LED_F2

LED_E1

LED_E2

LED_F1

LED_C2

LED_C1

LED_D1

LED_B2

LED_A1

LED_A2

JIPMB1

FAN8

FAN7

FAN6

FAN5

FAN4

FAN3

FAN2

FAN1

JVRM2

JVRM1

JWD2

JPG1

JPB1

LED1

JUIDB2

SXB3B

PSU2

PSU1

JGPW2

JGPW3

JGPW1

JPW22

JPW23

JPW21

JGPW4

JPW19

JTPM1

SXB1_3

SXB3C

SXB1_1

SXB3A

BAR CODE

BIOS LICENSE

IPMI CODE

P2-DIMMG2

P2-DIMMG1

P2-DIMMH1

P2-DIMMH2

CPU2

SXB1B

SXB1C

SXB1A

CPU1_PORT3

CPU2_PORT2

USB3/4 (3.0)

JPME2

GPU PWR3

GPU PWR2

CPU2_PORT1

SXB2

VGA

P2-DIMMF2

P2-DIMMF1

GPU PWR4

I-SATA4

P2-DIMME2

P2-DIMME1

I-SATA5

S-SATA0~3

COM1

I-SATA0~3

IPMI_LAN

USB 0/1(3.0)

CPU1_PORT2

P1-DIMMC1

P1-DIMMC2

P1-DIMMD2

P1-DIMMD1

CPU2_PORT3

CPU1_PORT1

CPU1

P1-DIMMB2

P1-DIMMB1

P1-DIMMA2

GPU PWR1

P1-DIMMA1

BP PWR2

BP PWR1

CLOSE 1st

OPEN 1st

CLOSE 1st

OPEN 1st

SXB1_2

PLD1

C612

A1

LED_D2

LED2

HDD_LED1

1

LED_B1

BMC

BMC_HB_LED1

JA1

1-4

X10DRU-X/X10DRU-XLL Motherboard User’s Manual

Notes:

•See Chapter 2 for detailed information jumpers, I/O ports, connectors and ex-

pansion slots. " " indicates the location of "Pin 1".

• Components/Jumpers/LED Indicators that are not documented in this manual

are reserved for internal testing only.

X10DRU-X(LL) Motherboard Quick Reference

X10DRU-X

REV:1.01

I-SGPIO2

JF1

JL1

DESIGNED IN USA

JUSBA1

JBAT1

JBT1

JSD2

JSD1

SP1

LED_H1

LED_G2

LED_G1

LED_H2

LED_F2

LED_E1

LED_E2

LED_F1

LED_C2

LED_C1

LED_D1

LED_B2

LED_A1

LED_A2

JIPMB1

FAN8

FAN7

FAN6

FAN5

FAN4

FAN3

FAN2

FAN1

JVRM2

JVRM1

JWD2

JPG1

JPB1

LED1

JUIDB2

SXB3B

PSU2

PSU1

JGPW2

JGPW3

JGPW1

JPW22

JPW23

JPW21

JGPW4

JPW19

JTPM1

SXB1_3

SXB3C

SXB1_1

SXB3A

BAR CODE

BIOS LICENSE

IPMI CODE

P2-DIMMG2

P2-DIMMG1

P2-DIMMH1

P2-DIMMH2

CPU2

SXB1B

SXB1C

SXB1A

CPU1_PORT3

CPU2_PORT2

USB3/4 (3.0)

JPME2

GPU PWR3

GPU PWR2

CPU2_PORT1

SXB2

VGA

P2-DIMMF2

P2-DIMMF1

GPU PWR4

I-SATA4

P2-DIMME2

P2-DIMME1

I-SATA5

S-SATA0~3

COM1

I-SATA0~3

IPMI_LAN

USB 0/1(3.0)

CPU1_PORT2

P1-DIMMC1

P1-DIMMC2

P1-DIMMD2

P1-DIMMD1

CPU2_PORT3

CPU1_PORT1

CPU1

P1-DIMMB2

P1-DIMMB1

P1-DIMMA2

GPU PWR1

P1-DIMMA1

BP PWR2

BP PWR1

CLOSE 1st

OPEN 1st

CLOSE 1st

OPEN 1st

SXB1_2

PLD1

C612

A1

LED_D2

LED2

HDD_LED1

1

LED_B1

BMC

BMC_HB_LED1

JA1

Chapter 1: Overview

1-5

X10DRU-X(LL) Motherboard Jumpers

Jumper

Description Default Setting

JBT1 Clear CMOS See Chapter 2

JPB1 BMC Enabled Pins 1-2 (Enabled)

JPG1 VGA Enabled Pins 1-2 (Enabled)

JPME2 Manufacturing Mode Pins 1-2 (Normal)

JWD2 Watch Dog Pins 1-2 (RST)

JVRM1/JVRM2 I2C Bus for VRM Pins 1-2 (BMC: Normal)

X10DRU-X(LL) Motherboard Connectors

Connectors Description

Battery (JBAT1) Onboard Battery (See the Note on P. 1-3.)

COM1 Serial Port/COM Port 1

FAN1 - FAN8 System Cooling Fan Header

IPMI LAN IPMI_Dedicated LAN supported by Aspeed Controller

I-SATA0~5 SATA 3.0 Connectors supported by Intel® PCH

I-SGPIO2 Serial Link General Purpose I/O Header

JF1 Front Panel Control Header

JGPW1 - JGPW4 GPU/VGA Power Connectors

JIPMB1 GPU/PCIe Auxiliary Power Connectors

JL1 Chassis Intrusion Detection Header

JPW19/21/22/23 Storage backplane Power Connectors

JSD1/JSD2 SATA DOM (Device_On_Module) Power Connectors

JTPM1 TPM (Trusted Platform Module)/Port 80

JUIDB2 UID (Unit Identier) Switch

JUSBA1 USB 3.0 Type A Connector

S-SATA0~3 SATA 3.0 Connectors supported by Intel® SCU

SP1 Internal Speaker/Buzzer

SXB1_1/1_2/1_3 PCI-E 3.0 (x16 + x16) Left Riser Card Slot

SXB2 PCI-E 3.0 (x8) + PCI-E 2.0 (x4 in x8) Center Riser

Card Slot

SXB3A/3B/3C PCI-E 3.0 (x24 +x16) Right Ultra Riser Card Slot

USB0/1 Back panel USB 3.0 Ports

USB3/4 Front panel Accessible USB 3.0 Ports

VGA Backpanel VGA Port

1-6

X10DRU-X/X10DRU-XLL Motherboard User’s Manual

X10DRU-X(LL) Motherboard LED Indicators

LED Description State Status

BMC_HB_LED1 BMC Heartbeat LED Green: Blinking BMC Normal

HDD_LED1 Hard Drive LED Green: On HDD Normal

LED1 UID LED Blue: On Unit Identied

LED2 Power LED Green: On Power On

LED A1/A2 Memory ECC Error

LED B1/B2 Memory ECC Error

LED C1/C2 Memory ECC Error

LED D1/D2 Memory ECC Error

LED E1/E2 Memory ECC Error

LED F1/F2 Memory ECC Error

LED G1/G2 Memory ECC Error

LED H1/H2 Memory ECC Error

Chapter 1: Overview

1-7

CPU

• Dual Intel

®

E5-2600(V3) Series Processors (Socket

R3 LGA 2011); each processor supports two full-width

Intel QuickPath Interconnect (QPI) links (with Data

Transfer Rate of up to 9.6 GT/s per QPI)

Memory

• Integrated memory controller supports: Up to 1 TB

of ECC DDR4 (288-pin) Load Reduced (LRDIMM)

modules at 1333/1600/1866*/2133** MHz in 16 slots.

(*Maximum for 2 DIMMs per channel, ** Maximum for

1 DIMM per channel)

Note: For the latest CPU/memory updates,

please refer to our website at http://www.super-

micro.com/products/motherboard.

DIMM Sizes

• Up to 64GB @ 1.2V

Chipset

• Intel

®

PCH C612

Expansion

• SXB1 supports PCIe 3.0 x16 from CPU1 and PCIe

3.0 x16 from CPU2

• SXB2 supports PCIe 3.0 x8 from CPU2 and PCIe 2.0

x4 from CPU2

• SXB3 supports PCIe 3.0 x8 from CPU1, PCIe 3.0 x16

from CPU1, and PCIe 3.0 x16 from CPU2.

Slots

Graphics

• ASpeed 2400 BMC Controller with integrated VGA/2D

Graphics Controller 1920x1200 @ 60Hz 32bpp

Network

• NIC integrated into Ultra Riser card plugged into

SXB3

I/O Devices

SATA Connections

• SATA Ports Six (6) SATA 3.0 ports supported

by Intel® PCH (I-SATA0-5)

Four (4) SATA 3.0 ports supported

by Intel® SCU (S-SATA0-3)

• RAID RAID 0, 1, 5, 10

IPMI 2.0

• IPMI 2.0 supported by the ASpeed 2400 BMC

Motherboard Features

1-8

X10DRU-X/X10DRU-XLL Motherboard User’s Manual

Serial (COM) Port

• One (1) Fast UART 16550 Connection: 9-pin RS232

port

VGA

• Rear VGA Port

Peripheral
Devices

USB Devices

• Two (2) USB 3.0 on rear

• Two (2) USB 3.0 for front panel

• One (1) USB 3.0 Type A

BIOS

• 128 Mb AMI SPI BIOS Flash ROM

• APM 1.2, DMI 2.3, PCI 2.3, ACPI 1.0/2.0/3.0,

USB Keyboard, Plug & Play (PnP), UEFI 2.3, and

SMBIOS 2.7 or later.

Power

• ACPI Power Management

• Power-on mode for AC power recovery

• Intel

®

Intelligent Power Node Manager (available

when the NMView utility is installed)

• Management Engine

• Riser Card auto-detection

System
Health

Monitoring

System Health Monitoring

• +3.3V, +5V, +/-12V, +3.3V Stdby, +5V Stdby, VBAT,

and memory.

• CPU 5-Phase switching voltage regulator

• CPU/System overheat LED and control

• CPU Thermal Trip support

• Thermal Monitor 2 (TM2) support

Fan Control

• Fan status monitoring with rmware 4-pin fan speed

control

• Low noise fan speed control

LED Indicators

• BMC (BaseBoard Management) LED

• InniBand LED

• UID/Remote UID LED

Chapter 1: Overview

1-9

System
Management

• PECI (Platform Environment Conguration Interface)

2.0 support

• System resource alert via SuperDoctor

®

5

• Thermal Monitor 2 (TM2) support

• SuperDoctor

®

5, Watch Dog, NMI

• Chassis Intrusion Header and Detection

Dimensions

• 16.8" (L) x 17" (W) (426.72 mm x 431.8 mm)

1-10

X10DRU-X/X10DRU-XLL Motherboard User’s Manual

System Block Diagram

Notes: 1. This is a general block diagram and may not exactly represent

the features on your motherboard. See the Motherboard Features pages

for the actual specications of each motherboard. 2. This block diagram

was provided for your reference only.

C

D

#2

SocketID 00

#1#1#1#1

#2

QPI0

DMI

DDR4 DIMM

A

PROCESSOR

DDR4 DIMM

DDR4 DIMM

B

DDR4 DIMM

H

G

#2

SocketID 01

#1#1#1

#1

#2

DDR4 DIMM

E

PROCESSOR

DDR4 DIMM

DDR4 DIMM

F

DDR4 DIMM

QPI1

DMI

Upper

Upper Lower

x4

x8

x16

NIC

port 0,1

REAR

port 3

TYPE-A

NCSI

Port A

x8

DDR3

UART

NCSI

Port A

0~7

Lower

x16

Port C

Port C

11~15

x16

Port C

Port C
0~10

Port B

x16

Port B

Port B
8~15

Port B
0~7

DDR3

VGA

VGA

LAN

32MB BMC
SPI FLASH

BMC
AST2400

PHY
RTL8211E

VGA

WIO

HWM

SPI

PE

SPI

USB

LPC

COM1, COM2

SPI

PE [3]

LPC

USB 2.0 [6,7]

PCH

xSATA Gen3 [0...3]

SATA Gen3 [0...3]

SATA Gen3 [4,5]

JS1

JS2

TPM Header

I_SATA4

I_SATA5

CPU1

CPU2

#2 #2

16GB/s

4GB/s

32GB/s

32GB/s

PE1

PE2 PE3QP10 QP11

QPI

9GT/s
Polarity Inversion

Ultra IO

WIO

9GT/s
Polarity Inversion

QPI

4GB/s

16GB/s

32GB/s

32GB/s

PE1 PE2PE3

#2

#2

MUX

16MB BIOS
SPI FLASH

Chapter 1: Overview

1-11

1-2 Processor and Chipset Overview

Built upon the functionality and capability of the Intel® E5-2600(V3) Series proces-

sors (Socket R3) and the Intel® C612 PCH, the X10DRU-X(-XLL) Series mother-

board provides the best balanced solution of performance, power efciency, and

features to address the diverse needs of next-generation data centers.

With support of new Intel® Microarchitecture 22nm Process Technology and Intel

®

Silicon View Technology, the X10DRU-X(-XLL) Series motherboard dramatically
reduces overhead associated with encryption, accelerates system boot security,
and enhances virtual media integration as well as remote system management

and monitoring.

The PCH C612 chip in conjunction with the E5-2600 v3 processors support the

following features:

•DDR4 288-pin memory support on Socket R3

•Integrated Clocking capable of extending to most 2S platforms

•Support for MCTP Protocol and ME

•Support of SMBus speeds of up to 1 MHz for BMC connectivity

•GSX capable of GPIO expansion

•Improved I/O capabilities to high-storage-capacity congurations

•Intel

®

SVT support capability

•Flexible Management Infrastructure focused on Run Time with support for

MCTP Protocol/End Points and Management trafc over DMI

•Embedded Platform SW Services capability

•SPI Enhancements with address space large enough for 2x BIOS

•Intel

®

Node Manager 3.0 (with BE, EE options) for advanced power monitoring,

capping and management for BMC enhancement

•BMC supports remote management, virtualization, and the security package

for enterprise platforms

1-12

X10DRU-X/X10DRU-XLL Motherboard User’s Manual

1-3 Special Features

Recovery from AC Power Loss

The Basic I/O System (BIOS) provides a setting that determines how the system will

respond when AC power is lost and then restored to the system. You can choose for

the system to remain powered off (in which case you must press the power switch

to turn it back on), or for it to automatically return to the power-on state. See the

Advanced BIOS Setup section for this setting. The default setting is Last State.

1-4 System Health Monitoring

This section describes the features of system health monitoring of the motherboard.

This motherboard has an onboard Baseboard Management Controller (BMC) chip

that supports system health monitoring. An onboard voltage monitor will scan the

voltages of onboard chipset, memory, CPU, and battery continuously. Once a

voltage becomes unstable, a warning is given, or an error message is sent to the

screen. The user can adjust the voltage thresholds to dene the sensitivity of the

voltage monitor.

Fan Status Monitor with Firmware Control

The system health monitor chip can check the RPM status of a cooling fan. The

CPU and chassis fans are controlled by BIOS Thermal Management through the

backpanel.

Environmental Temperature Control

System Health sensors monitor temperatures and voltage settings of onboard

processors and the system in real time via the IPMI interface. Whenever the tem-

perature of the CPU or the system exceeds a user-dened threshold, system/CPU

cooling fans will be turned on to prevent the CPU or the system from overheating.

Note: To avoid possible system overheating, please be sure to provide

adequate airow to your system.

System Resource Alert

This feature is available when used with SuperDoctor® 5 in the Windows® OS or

in the Linux environment. SuperDoctor is used to notify the user of certain system

events. For example, you can congure SuperDoctor to provide you with warnings

when the system temperature, CPU temperatures, voltages and fan speeds go

beyond a predened range.

Chapter 1: Overview

1-13

1-5 ACPI Features

ACPI stands for Advanced Conguration and Power Interface. The ACPI specica-

tion denes a exible and abstract hardware interface that provides a standard way

to integrate power management features throughout a computer system, including

its hardware, operating system and application software. This enables the system

to automatically turn on and off peripherals such as CD-ROMs, network cards, hard

disk drives and printers.

In addition to enabling operating_system-directed power management, ACPI also

provides a generic system event mechanism for Plug and Play, and an operating

system-independent interface for conguration control. ACPI leverages the Plug and

Play BIOS data structures, while providing a processor architecture-independent

implementation that is compatible with Windows 7, Windows 8, and Windows 2012

Operating Systems.

1-6 Power Supply

As with all computer products, a stable power source is necessary for proper and

reliable operation. It is even more important for processors that have high CPU

clock rates. In areas where noisy power transmission is present, you may choose

to install a line lter to shield the computer from noise. It is recommended that you

also install a power surge protector to help avoid problems caused by power surges.

1-7 Serial Port

The X10DRU-X(-LL) motherboard supports one serial communication connection.

COM Port 1 can be used for input/output. The UART provide legacy speed with

baud rate of up to 115.2 Kbps as well as an advanced speed with baud rates of

250 K, 500 K, or 1 Mb/s, which support higher speed modems.

1-8 Advanced Power Management

The following new advanced power management features are supported by the

motherboard.

Intel® Intelligent Power Node Manager (NM) (Available
when the NMView software is installed)

The Intel® Intelligent Power Node Manager (IPNM) provides your system with

real-time thermal control and power management for maximum energy efciency.

Although IPNM Specication Version 1.5/2.0 is supported by the BMC (Baseboard

Management Controller), your system must also have IPNM-compatible Manage-

ment Engine (ME) rmware installed to use this feature.

1-14

X10DRU-X/X10DRU-XLL Motherboard User’s Manual

Note: Support for IPNM Specication Version 1.5 or 2.0 depends on the

power supply used in the system.

Management Engine (ME)

The Management Engine, which is an ARC controller embedded in the PCH, pro-

vides Server Platform Services (SPS) to your system. The services provided by

SPS are different from those provided by the ME on client platforms.

Chapter 2: Installation

2-1

Chapter 2

Installation

2-1 Standardized Warning Statements

The following statements are industry-standard warnings, provided to warn the user

of situations which have the potential for bodily injury. Should you have questions or

experience difculty, contact Supermicro's Technical Support department for assis-

tance. Only certied technicians should attempt to install or congure components.

Read this section in its entirety before installing or conguring components in the

Supermicro chassis.

Battery Handling

Warning!

There is a danger of explosion if the battery is replaced incorrectly. Replace the

battery only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's instructions

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。 交換する電池はメー
カーが推奨する型、または同等のものを使用下さい。 使用済電池は製造元の指示に従

って処分して下さい。

警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更
换原有电池。请按制造商的说明处理废旧电池。

警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有
電池。請按照製造商的說明指示處理廢棄舊電池。

Warnung

Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die

Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.

Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.

2-2

X10DRU-X/X10DRU-LL Motherboard User’s Manual

Attention

Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer

que par une pile de type semblable ou équivalent, recommandée par le fabricant.

Jeter les piles usagées conformément aux instructions du fabricant.

¡Advertencia!

Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Re-

emplazar la batería exclusivamente con el mismo tipo o el equivalente recomen-

dado por el fabricante. Desechar las baterías gastadas según las instrucciones

del fabricante.

!הרהזא

תנכס תמייקץוציפ .הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי

גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ.

תוללוסה קוליס תושמושמה עצבל שי .ןרציה תוארוה יפל









경고!

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일
하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다. 제조사
의 안내에 따라 사용된 배터리를 처리하여 주십시오.

Waarschuwing

Er is ontplofngsgevaar indien de batterij verkeerd vervangen wordt. Vervang de

batterij slechts met hetzelfde of een equivalent type die door de fabrikant aan-

bevolen wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften

afgevoerd te worden.

Chapter 2: Installation

2-3

Product Disposal

Warning!

Ultimate disposal of this product should be handled according to all national laws

and regulations.

製品の廃棄

この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が

ありま す。

警告
本产品的废弃处理应根据所有国家的法律和规章进行。

警告
本產品的廢棄處理應根據所有國家的法律和規章進行。

Warnung

Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen

des Landes erfolgen.

¡Advertencia!

Al deshacerse por completo de este producto debe seguir todas las leyes y regla-

mentos nacionales.

Attention

La mise au rebut ou le recyclage de ce produit sont généralement soumis à des

lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de

l'organisme compétent.

2-4

X10DRU-X/X10DRU-LL Motherboard User’s Manual

2-2 Static-Sensitive Devices

Electrostatic Discharge (ESD) can damage electronic com ponents. To avoid pos-

sible damage to your system board, it is important to handle it very carefully. The

following measures are generally sufcient to protect your equipment from ESD.

Precautions

•Use a grounded wrist strap designed to prevent static discharge.

•Touch a grounded metal object before removing the board from the antistatic

bag.

•Handle the board by its edges only; do not touch its components, peripheral

chips, memory modules or gold contacts.

•When handling chips or modules, avoid touching their pins.

•Put the motherboard and peripherals back into their antistatic bags when not

in use.

•For grounding purposes, make sure that your system chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and

the motherboard.

Unpacking

The motherboard is shipped in antistatic packaging to avoid static damage. When

unpacking the board, make sure that the person handling it is static protected.

Chapter 2: Installation

2-5

X10DRU-X

REV:1.01

I-SGPIO2

JF1

JL1

DESIGNED IN USA

JUSBA1

JBAT1

JBT1

JSD2

JSD1

SP1

LED_H1

LED_G2

LED_G1

LED_H2

LED_F2

LED_E1

LED_E2

LED_F1

LED_C2

LED_C1

LED_D1

LED_B2

LED_A1

LED_A2

JIPMB1

FAN8

FAN7

FAN6

FAN5

FAN4

FAN3

FAN2

FAN1

JVRM2

JVRM1

JWD2

JPG1

JPB1

LED1

JUIDB2

SXB3B

PSU2

PSU1

JGPW2

JGPW3

JGPW1

JPW22

JPW23

JPW21

JGPW4

JPW19

JTPM1

SXB1_3

SXB3C

SXB1_1

SXB3A

BAR CODE

BIOS LICENSE

IPMI CODE

P2-DIMMG2

P2-DIMMG1

P2-DIMMH1

P2-DIMMH2

CPU2

SXB1B

SXB1C

SXB1A

CPU1_PORT3

CPU2_PORT2

USB3/4 (3.0)

JPME2

GPU PWR3

GPU PWR2

CPU2_PORT1

SXB2

VGA

P2-DIMMF2

P2-DIMMF1

GPU PWR4

I-SATA4

P2-DIMME2

P2-DIMME1

I-SATA5

S-SATA0~3

COM1

I-SATA0~3

IPMI_LAN

USB 0/1(3.0)

CPU1_PORT2

P1-DIMMC1

P1-DIMMC2

P1-DIMMD2

P1-DIMMD1

CPU2_PORT3

CPU1_PORT1

CPU1

P1-DIMMB2

P1-DIMMB1

P1-DIMMA2

GPU PWR1

P1-DIMMA1

BP PWR2

BP PWR1

CLOSE 1st

OPEN 1st

CLOSE 1st

OPEN 1st

SXB1_2

PLD1

C612

A1

LED_D2

LED2

HDD_LED1

1

LED_B1

BMC

BMC_HB_LED1

JA1

2-3 Motherboard Installation

All motherboards have standard mounting holes to t different types of chassis.

Make sure that the locations of all the mounting holes for both motherboard and

chassis match. Although a chassis may have both plastic and metal mounting fas-

teners, metal ones are highly recommended because they ground the motherboard

to the chassis. Make sure that the metal standoffs click in or are screwed in tightly.

Then use a screwdriver to secure the motherboard onto the motherboard tray.

Tools Needed

•Phillips Screwdriver

•Pan head screws (15 pieces)

•Standoffs (15 pieces, if needed)

Location of Mounting Holes

There are fteen (15) mounting holes on this motherboard indicated by the arrows.

Caution: 1) To avoid damaging the motherboard and its components,

please do not use a force greater than 8 lb/inch on each mounting screw

during motherboard installation. 2) Some components are very close to

the mounting holes. Please take precautionary measures to prevent dam-

age to these components when installing the motherboard to the chassis.

2-6

X10DRU-X/X10DRU-LL Motherboard User’s Manual

Installing the Motherboard

1. Install the I/O shield into the chassis.

2. Locate the mounting holes on the motherboard.

3. Locate the matching mounting holes on the chassis. Align the mounting holes

on the motherboard against the mounting holes on the chassis.

4. Install standoffs in the chassis as needed.

5. Install the motherboard into the chassis carefully to avoid damaging mother-

board components.

6. Using the Phillips screwdriver, insert a Pan head #6 screw into a mounting

hole on the motherboard and its matching mounting hole on the chassis.

7. Repeat Step 5 to insert #6 screws into all mounting holes.

8. Make sure that the motherboard is securely placed in the chassis.

Note: Images displayed are for illustration only. Your chassis or compo-

nents might look different from those shown in this manual.

Chapter 2: Installation

2-7

OPEN 1st

WARNING!

2-4 Processor and Heatsink Installation

Warning: When handling the processor package, avoid placing direct pressure on

the label area.

Notes:

•Always connect the power cord last, and always remove it before adding,

removing or changing any hardware components. Make sure that you install

the processor into the CPU socket before you install the CPU heatsink.

•If you buy a CPU separately, make sure that you use an Intel-certied multi-

directional heatsink only.

•Make sure to install the system board into the chassis before you install

the CPU heatsink.

•When receiving a motherboard without a processor pre-installed, make sure

that the plastic CPU socket cap is in place and none of the socket pins are

bent; otherwise, contact your retailer immediately.

•Refer to the Supermicro website for updates on CPU support.

Press down

on

Load Lever

labeled 'Open 1st'.

Installing the LGA2011 Processor

1. There are two load levers on the LGA2011 socket. To open the socket cover,

rst press and release the load lever labeled 'Open 1st'.

OPEN 1st

WARNING!

21

2-8

X10DRU-X/X10DRU-LL Motherboard User’s Manual

OPEN 1st

WARNING!

2. Press the second load lever labeled 'Close 1st' to release the load plate that

covers the CPU socket from its locking position.

3. With the 'Close 1st' lever fully retracted, gently push down on the 'Open 1st'

lever to open the load plate. Lift the load plate to open it completely.

OPEN 1st

WARNING!

OPEN 1st

WARNING!

1

2

Press down on

Load

Lever 'Close 1st'

WARNING!

1

Pull lever away from
the socket

2

Gently push
down to pop the
load plate open.