Supermicro SuperO X10DRC-T4+, SuperO X10DRC-LN4+, SuperO X10DRi-T4+, SuperO X10DRi-LN4+, X10DRC-LN4+ User Manual

USER’S MANUAL

Revision 1.0b

X10DRC-T4+

X10DRC-LN4+

X10DRi-T4+

X10DRi-LN4+

Manual Revision 1.0b
Release Date: Feb. 18, 2015
Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy any part of
this document.
Information in this document is subject to change without notice. Other products and companies referred to herein
are trademarks or registered trademarks of their respective companies or mark holders.
Copyright © 2015 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

The information in this user’s manual has been carefully reviewed and is believed to be accurate.
The vendor assumes no responsibility for any inaccuracies that may be contained in this document,
and makes no commitment to update or to keep current the information in this manual, or to notify
any person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our website at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product
described in this manual at any time and without notice. This product, including software and docu­mentation, is the property of Supermicro and/or its licensors, and is supplied only under a license.
Any use or reproduction of this product is not allowed, except as expressly permitted by the terms
of said license.

IN NO EVENT WILL SUPER MICRO COMPUTER, INC. BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE
USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGES. IN PARTICULAR, SUPER MICRO COMPUTER, INC.
SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED
WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING,
INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between the manufacturer and the customer shall be governed by the laws of
Santa Clara County in the State of California, USA. The State of California, County of Santa Clara
shall be the exclusive venue for the resolution of any such disputes. Supermicro's total liability for
all claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class
A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the manufacturer’s instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference, in which case you will be required to correct the interference at your
own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate
warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”.

WARNING: Handling of lead solder materials used in this
product may expose you to lead, a chemical known to
the State of California to cause birth defects and other
reproductive harm.

Preface

iii

Preface

This manual is written for system integrators, IT Professionals, and

knowledgeable end users. It provides information for the installation and use of the

X10DRC/i-LN4+/-T4+ motherboard.

About This Motherboard

The Super X10DRC/i-LN4+/-T4+ motherboard supports dual Intel E5-2600v3 Series

processors (Socket R3) that offer the new Intel Microarchitecture 22nm Processing

Technology, delivering the most-balanced solution of performance, power efciency,

and features to address the diverse needs of next-generation data centers. With the

PCH C612 built in, the X10DRC/i-LN4+/-T4+ motherboard supports MCTP Protocol,

and Intel® Node Manager 3.0. This motherboard is ideal for visualization, CRM,

storage, and general server platforms. Please refer to our website (http://www.

supermicro.com) for CPU and memory support updates.

Manual Organization

Chapter 1 describes the features, specications and performance of the moth-

erboard. It also provides detailed information about the Intel PCH C612 chipset.

Chapter 2 provides hardware installation instructions. Read this chapter when in-

stalling the processor, memory modules and other hardware components into the

system. If you encounter any problems, see Chapter 3, which describes trouble-

shooting procedures for video, memory, and system setup stored in the CMOS.

Chapter 4 includes an introduction to BIOS, and provides detailed information on

running the BIOS Setup utility.

Appendix A provides BIOS Error Beep Codes.

Appendix B lists Software Installation Instructions.

Appendix C contains UEFI BIOS Recovery instructions.

Conventions Used in the Manual

Pay special attention to the following symbols for proper system installation:

Warning: Important information given to ensure proper system installation or to prevent

damage to the components or injury to yourself;

Note: Additional information given to differentiate between models or

instructions provided for proper system setup.

iv

X10DRC/i-LN4+/-T4+ Motherboard User’s Manual

Preface

v

Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

Website: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: [phone]

Fax: [phone]

Email: [e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Website: www.supermicro.nl

Asia-Pacic

Address: Super Micro Computer, Inc.

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 235

Taiwan (R.O.C)

Tel: [phone]

Fax: [phone]

Email: [e-mail]

Website: www.supermicro.com.tw

vi

Table of Contents

Preface

Chapter 1 Overview

1-1 Overview ......................................................................................................... 1-1

1-2 Processor and Chipset Overview...................................................................1-11

1-3 Special Features ........................................................................................... 1-12

1-4 System Health Monitoring ............................................................................. 1-12

1-5 ACPI Features ............................................................................................... 1-13

1-6 Power Supply ................................................................................................ 1-13

1-7 Advanced Power Management ..................................................................... 1-14

Intel® Intelligent Power Node Manager (NM) (Available when the Supermicro

Power Manager [SPM] is Installed) .............................................................. 1-14

Management Engine (ME) ............................................................................ 1-14

Chapter 2 Installation

2-1 Standardized Warning Statements ................................................................. 2-1

2-2 Static-Sensitive Devices .................................................................................. 2-4

2-3 Motherboard Installation .................................................................................. 2-5

Tools Needed .................................................................................................. 2-5

Location of Mounting Holes ............................................................................ 2-5

Installing the Motherboard .............................................................................. 2-6

2-4 Processor and Heatsink Installation................................................................ 2-7

Installing the LGA2011 Processor ................................................................. 2-7

Installing a Passive CPU Heatsink ................................................................2-11

Removing the Heatsink ................................................................................. 2-12

2-5 Installing and Removing the Memory Modules ............................................. 2-13

Installing & Removing DIMMs ....................................................................... 2-13

Removing Memory Modules ......................................................................... 2-13

2-6 Control Panel Connectors and I/O Ports ...................................................... 2-16

Back Panel Connectors and I/O Ports .......................................................... 2-16

Back Panel I/O Port Locations and Denitions ........................................... 2-16

Serial Ports ............................................................................................... 2-17

Video Connection ..................................................................................... 2-17

Universal Serial Bus (USB) ...................................................................... 2-18

GLAN/10G-LAN (TLAN) Ports & IPMI_LAN Port ..................................... 2-19

Unit Identier Switch/UID LED Indicator .................................................. 2-20

Front Control Panel ....................................................................................... 2-21

Front Control Panel Pin Denitions............................................................... 2-22

X10DRC/i-LN4+/-T4+ Motherboard User’s Manual

vii

Table of Contents

NMI Button ............................................................................................... 2-22

Power LED .............................................................................................. 2-22

HDD/UID LED .......................................................................................... 2-23

NIC1/NIC2 LED Indicators ....................................................................... 2-23

Overheat (OH)/Fan Fail/PWR Fail/UID LED ............................................ 2-24

Power Fail LED ........................................................................................ 2-24

Reset Button ........................................................................................... 2-25

Power Button ........................................................................................... 2-25

2-7 Connecting Cables ........................................................................................ 2-26

Power Connectors ................................................................................... 2-26

Fan Headers ............................................................................................. 2-27

Chassis Intrusion ..................................................................................... 2-27

Internal Speaker ....................................................................................... 2-28

DOM Power Connectors .......................................................................... 2-28

TPM/Port 80 Header ................................................................................ 2-29

Standby Power Header ............................................................................ 2-29

Power SMB (I2C) Connector .................................................................... 2-30

IPMB ......................................................................................................... 2-30

T-SGPIO1/2 & S-SGPIO1 Headers .......................................................... 2-31

Power LED/Speaker ................................................................................. 2-31

2-8 Jumper Settings ............................................................................................ 2-32

Explanation of Jumpers ................................................................................ 2-32

LAN Enable/Disable ................................................................................. 2-32

CMOS Clear ............................................................................................. 2-33

Watch Dog Enable/Disable ...................................................................... 2-33

VGA Enable .............................................................................................. 2-34

BMC Enable ............................................................................................ 2-34

I2C Bus to PCI-Exp. Slots ........................................................................ 2-35

Manufacturer Mode Select ....................................................................... 2-36

SAS Enable (For X10DRC-LN4+/T4+) ..................................................... 2-36

2-9 LED Indicators ............................................................................................... 2-37

LAN Port LEDs ......................................................................................... 2-37

IPMI Dedicated LAN LEDs ....................................................................... 2-37

Onboard Power LED ............................................................................... 2-38

BMC Heartbeat LED ................................................................................ 2-38

SAS Heartbeat LED (for the X10DRC-LN4+/T4+ only) ........................... 2-39

SAS Activity LED (for the X10DRC-LN4+/T4+ only) ................................ 2-39

SAS Error LED (for the X10DRC-LN4+/T4+ only) ................................... 2-40

viii

2-10 SATA/SAS Connections ................................................................................ 2-41

SATA 3.0 Ports ......................................................................................... 2-41

SAS 3.0 Ports (for the X10DRC-LN4+/T4+) ............................................ 2-42

Chapter 3 Troubleshooting

3-1 Troubleshooting Procedures ........................................................................... 3-1

3-2 Technical Support Procedures ........................................................................ 3-5

3-3 Battery Removal and Installation .................................................................... 3-6

3-4 Frequently Asked Questions ........................................................................... 3-7

3-5 Returning Merchandise for Service................................................................. 3-8

Chapter 4 BIOS

4-1 Introduction ...................................................................................................... 4-1

4-2 Main Setup ...................................................................................................... 4-2

4-3 Advanced Setup Congurations...................................................................... 4-4

4-4 Event Logs .................................................................................................... 4-32

4-5 IPMI ............................................................................................................... 4-34

4-6 Security Settings ........................................................................................... 4-36

4-7 Boot Settings ................................................................................................. 4-37

4-8 Save & Exit ................................................................................................... 4-39

Appendix A BIOS Error Beep Codes

A-1 BIOS Error Beep Codes .................................................................................A-1

Appendix B Software Installation Instructions

B-1 Installing Software Programs ..........................................................................B-1

B-2 Installing SuperDoctor5 ...................................................................................B-2

Appendix C UEFI BIOS Recovery Instructions

C-1 An Overview to the UEFI BIOS ......................................................................C-1

C-2 How to Recover the UEFI BIOS Image (-the Main BIOS Block)....................C-1

C-3 To Recover the Main BIOS Block Using a USB-Attached Device..................C-1

X10DRC/i-LN4+/-T4+ Motherboard User’s Manual

Chapter 1: Overview

1-1

Chapter 1

Overview

1-1 Overview

Checklist

Congratulations on purchasing your computer motherboard from an acknowledged

leader in the industry. Supermicro boards are designed with the utmost attention to

detail to provide you with the highest standards in quality and performance.

Please check that the following items have all been included with your motherboard.

If anything listed here is damaged or missing, contact your retailer.

The following items are included in the retail box.

• One (1) Supermicro Mainboard

•Two (2) SATA Cables (CBL-0044L x2) (X10DRC-LN4+/T4+ Only)

•Two (2) SAS Cables (CBL-SAST-0532 x2) (X10DRC-LN4+/T4+ Only)

•Six (6) SATA Cables (CBL-0044L x6) (X10DRi-LN4+/T4+ Only)

• One (1) I/O Shield (MCP-260-00042-0N)

• One (1) Quick Reference Guide (MNL#1560-QRG)

Note 1: For your system to work properly, please follow the links below

to download all necessary drivers/utilities and the user's manual for your

motherboard.

•Supermicro product manuals: http://www.supermicro.com/support/manuals/

•Product Drivers and utilities: ftp://ftp.supermicro.com/

Note 2: For safety considerations, please refer to the complete list of safety

warnings posted on the Supermicro website at http://www.supermicro.com/

about/policies/safety_information.cfm.

If you have any questions, please contact our support team at support@supermicro.

com.

1-2

X10DRC/i-LN4+/-T4+ Motherboard User’s Manual

X10DRC/i-LN4+/-T4+ Motherboard Image

Note: All graphics shown in this manual were based upon the latest PCB

Revision available at the time of publishing of the manual. The motherboard

you've received may or may not look exactly the same as the graphics

shown in this manual.

Chapter 1: Overview

1-3

Motherboard Layout

Note: For the latest CPU/Memory updates, please refer to our website at

http://www.supermicro.com/products/motherboard/ for details.

IPMI CODE

SAS CODE

SAN MAC

T-SGPIO1
T-SGPIO2

JD1

JS39

LEDS6

LEDS5

LEDM1

LE2

LE1

FANB

FANA

FAN4

FAN3

FAN2

FAN1

FAN5

FAN6

JBT1

JIPMB1

SP1

JPS7

JPG1

JPLAN1

JPLAN2

JWD1

JPME2

JI2C2

JVRM1

JPB1

JTPM1

JSD2

JSD1

JS1

JPP0

JPP1

JPWR2

JPWR1

J24

JPI2C1

BIOS
LICENSE

MAC CODE

BAR CODE

SAS 4~7 (3.0)

SAS 0~3 (3.0)

P1-DIMMD3

P1-DIMMD2

P1-DIMMD1

P1-DIMMC3

P1-DIMMC2

P1-DIMMB3

P1-DIMMB2

P1-DIMMB1

P1-DIMMA3

P1-DIMMA2

P2-DIMMH3

P2-DIMMH2

P2-DIMMH1

P2-DIMMG3

P2-DIMMG2

P2-DIMMF3

P2-DIMMF2

P2-DIMMF1

P2-DIMME3

P2-DIMME2

USB 7/8 (3.0)

USB 0/1

P1-DIMMC1

P1-DIMMA1

CPU2 SLOT6 PCI-E 3.0 X8

CPU2 SLOT5 PCI-E 3.0 X16

CPU2 SLOT4 PCI-E 2.0 X4 IN X8

JL1

S-SATA0

CPU1 SLOT3 PCI-E 3.0 X16

S-SATA1

S-SATA2

CPU2 SLOT2 PCI-E 3.0 X8

S-SATA3

I-SATA0

I-SATA3

I-SATA4

I-SATA1

CPU2 SLOT1 PCI-E 3.0 X8

COM2

I-SATA5

UID

VGA

LAN3/4

LAN1/2

IPMI_LAN

COM1

CPU2

CPU1

P2-DIMME1

P2-DIMMG1

I-SATA2

JI2C1

CLOSE 1st

OPEN 1st

CLOSE 1st

OPEN 1st

USB 6 (3.0)

BIOS

USB2/3

S-SGPIO1

X10DRC/i-LN4+(-T4+)

Rev. 1.01

BMC

LAN CTRL

LSI 3108
SAS CTRL

Intel PCH

USB4/5
(3.0)

JBAT1

TPM/PORT80

JUIDB1

Front CTRL Panel

JF1

FANC

JVRM2

JSTBY1

1

LAN CTRL

DS13

JPS1

1-4

X10DRC/i-LN4+/-T4+ Motherboard User’s Manual

Notes:

•See Chapter 2 for detailed information on jumpers, I/O ports and JF1 front

panel connections.

•" " indicates the location of "Pin 1".

•Jumpers/LED Indicators not indicated are for testing only.

•LAN1/LAN2/LAN3/LAN4 ports support Gigabit_LAN (GLAN) connections on the

X10DRC/i-LN4+, and 10G (T) LAN connections on the X10DRC/i-T4+.

•The LSI 3108 is available on the X10DRC-LN4+/T4+ only.

•Use only the correct type of onboard CMOS battery as specied by the manufac-

turer. Do not install the onboard battery upside down to avoid possible explosion.

X10DRC/i-LN4+/-T4+ Quick Reference

IPMI CODE

SAS CODE

SAN MAC

T-SGPIO1
T-SGPIO2

JD1

JS39

LEDS6

LEDS5

LEDM1

LE2

LE1

FANB

FANA

FAN4

FAN3

FAN2

FAN1

FAN5

FAN6

JBT1

JIPMB1

SP1

JPS7

JPG1

JPLAN1

JPLAN2

JWD1

JPME2

JI2C2

JVRM1

JPB1

JTPM1

JSD2

JSD1

JS1

JPP0

JPP1

JPWR2

JPWR1

J24

JPI2C1

BIOS
LICENSE

MAC CODE

BAR CODE

SAS 4~7 (3.0)

SAS 0~3 (3.0)

P1-DIMMD3

P1-DIMMD2

P1-DIMMD1

P1-DIMMC3

P1-DIMMC2

P1-DIMMB3

P1-DIMMB2

P1-DIMMB1

P1-DIMMA3

P1-DIMMA2

P2-DIMMH3

P2-DIMMH2

P2-DIMMH1

P2-DIMMG3

P2-DIMMG2

P2-DIMMF3

P2-DIMMF2

P2-DIMMF1

P2-DIMME3

P2-DIMME2

USB 7/8 (3.0)

USB 0/1

P1-DIMMC1

P1-DIMMA1

CPU2 SLOT6 PCI-E 3.0 X8

CPU2 SLOT5 PCI-E 3.0 X16

CPU2 SLOT4 PCI-E 2.0 X4 IN X8

JL1

S-SATA0

CPU1 SLOT3 PCI-E 3.0 X16

S-SATA1

S-SATA2

CPU2 SLOT2 PCI-E 3.0 X8

S-SATA3

I-SATA0

I-SATA3

I-SATA4

I-SATA1

CPU2 SLOT1 PCI-E 3.0 X8

COM2

I-SATA5

UID

VGA

LAN3/4

LAN1/2

IPMI_LAN

COM1

CPU2

CPU1

P2-DIMME1

P2-DIMMG1

I-SATA2

JI2C1

CLOSE 1st

OPEN 1st

CLOSE 1st

OPEN 1st

USB 6 (3.0)

BIOS

USB2/3

S-SGPIO1

X10DRC/i-LN4+(-T4+)

Rev. 1.01

BMC

LAN CTRL

LSI 3108
SAS CTRL

Intel PCH

USB4/5
(3.0)

JBAT1

TPM/PORT80

JUIDB1

Front CTRL Panel

JF1

FANC

JVRM2

JSTBY1

1

LAN CTRL

DS13

JPS1

Chapter 1: Overview

1-5

X10DRC/i-LN4+/-T4+ Jumpers

Jumper Description Default Setting

JBT1 Clear CMOS/Reset BIOS Conguration See Chapter 2

JI2C1/JI2C2 SMB to PCI-E Slots Pins 1-2 (Enabled)

JPB1 BMC Enable Pins 1-2 (Enabled)

JPG1 VGA Enable Pins 1-2 (Enabled)

JPLAN1 GLAN1/2 Enable (X10DRC/i-LN4+)

10G(T)_LAN1/2 Enable (X10DRC/i-T4+)

Pins 1-2 (Enabled)

JPLAN2 GLAN3/4 Enable (X10DRC/i-LN4+)

10G(T)_LAN3/4 Enable (X10DRC/i-T4+)

Pins 1-2 (Enabled)

JPME2 Manufacture (ME) Mode Select Pins 1-2 (Normal)

JPS1 SAS Enable Pins 1-2 (Enabled)

JWD1 Watch Dog Timer Enable Pins 1-2 (Reset)

X10DRC/i-LN4+/-T4+ Connectors

Connectors Description

Battery Onboard CMOS Battery (See Chpt. 3 for Used Battery Disposal)

(JBAT1)

COM1/COM2 Backplane COM Port1/Front Accessible COM2 Header

FAN1-6,
FANA-C

CPU/System Fan Headers

J24 24-pin ATX Main Power Connector (See Warning on Pg. 1-6.)

JD1 Speaker/Power LED

JF1 Front Panel Control Header

JIPMB1 4-pin External BMC I2C Header (for an IPMI Card)

JL1 Chassis Intrusion

JPI2C1 Power Supply SMBbus I2C Header

JPWR1/2 8-Pin Power Connectors

JSD1/JSD2 SATA DOM (Device on Module) Power Connectors

JTPM1 TPM (Trusted Platform Module)/Port 80 Header

JUIDB1 UID (Unit Identication) Button

LAN1/LAN2 Gigabit LAN(GLAN) Ethernet Ports 1/2 (X10DRC/i-LN4+)

10G(T) LAN Ethernet Ports 1/2 (X10DRC/i-T4+)

LAN3/LAN4 Gigabit LAN (GLAN) Ethernet Ports 3/4 (X10DRC/i-LN4+)

10G(T) LAN Ethernet Ports 3/4 (X10DRC/i-T4+)

(IPMI) LAN IPMI_Dedicated LAN support by the ASpeed controller

(I-)SATA 0-5 SATA 3.0 Connectors supported by Intel PCH (I-SATA 0-5)

(S-)SATA 0-3 SATA 3.0 Connectors supported by Intel SCU (S-SATA 0-3)

SAS0-3, 4-7
(3.0)

SAS 3.0 Connections supported by the LSI 3108 controller
(JS39) (for the X10DRC-LN4+/T4+ only)

1-6

X10DRC/i-LN4+/-T4+ Motherboard User’s Manual

Note: Available on the X10DRC-LN4+/T4+ only.

Warning: To avoid damaging the power supply or the motherboard, be sure to use

a power supply that contains a 24-pin and two 8-pin power connectors. Be sure to

connect the power supply to the 24-pin power connector (J24), and two 8-pin power

connectors (JPWR1, JPWR2) on the motherboard. Failure in doing so may void the

manufacturer warranty on your power supply and motherboard.

(CPU2) Slot1 PCI-Express 3.0 x8 Slot from CPU2

(CPU2) Slot2 PCI-Express 3.0 x8 Slot from CPU2

(CPU1) Slot3 PCI-Express 3.0 x16 Slot from CPU1

(CPU2) Slot4 PCI-Express 2.0 x4 in x8 Slot from CPU2

(CPU2) Slot5 PCI-Express 3.0 x16 Slot from CPU2

(CPU2) Slot6 PCI-Express 3.0 x8 Slot from CPU2

S-SGPIO1,
T-SGPIO1/2

Serial_Link General Purpose I/O Headers 1/2/3 (for SATA ports),
(T-SGPIO1 for I-SATA0-3, T-SGPIO2 for I-SATA4/5, S-SGPIO1
for S-SATA0-3)

SP1 Internal Speaker/Buzzer

JSTBY1 +5V Standby Power Header

(BP) USB 0/1
(2.0)

Backpanel USB 2.0 Ports 0/1

(BP) USB 4/5
(3.0)

Backpanel USB 3.0 Ports 4/5

(FP) USB 7/8
(3.0)

Front Accessible USB 3.0 Connection Header 7/8

(FP) USB 2/3
(2.0)

Front Accessible USB 2.0 Connection Header 2/3

(FP) USB 6
(3.0)

Front Accessible USB 3.0 Connection Header 6

VGA Backpanel VGA Port

X10DRC/i-LN4+/-T4+ LED Indicators

LED Description State Status

DS13 (Note below) SAS Heartbeat LED Green: Blinking SAS Normal

LE1 Rear UID LED Blue: On Unit Identied

LE2 Onboard Power LED Green: On System PWR On

LEDM1 BMC Heartbeat LED Green: Blinking BMC Normal

LEDS5 (Note below) SAS Activity LED Green: Blinking SAS Active

LEDS6 (Note below) SAS Error LED Red: On SAS Error(s)

Chapter 1: Overview

1-7

Motherboard Features

CPU

• Dual Intel

®

E5-2600v3 Series Processors (Socket

R3-LGA 2011); each processor supports dual full-

width Intel QuickPath Interconnect (QPI) links (of up

to 9.6 GT/s one direction per QPI)

Note: Both CPU’s need to be installed for full

access the PCI-E slots and on-board con-

trollers. See the attached block diagram to

determine which PCI-E slots or devices may

be impacted.

Memory

• Integrated memory controller supports: up to 1536

GB of Load Reduced (LRDIMM) or up to 768 GB of

Registered (RDIMM) DDR4 (288-pin) ECC modules

2133/1866/1600 MHz in 24 slots

Note: Memory speed support is pending on

the CPUs used in the motherboard. For the

latest CPU/memory updates, please refer to

our website at http://www.supermicro.com/

products/motherboard.

DIMM sizes

• DIMM Up to 64 GB (per DIMM) @ 1.2V

Chipset

• Intel® PCH C612

Expansion

• Three (3) PCI Express 3.0 x8 slots (CPU2 Slot1/

Slot2/Slot6)

• Two (2) PCI-Express 3.0 x16 slots (CPU1 Slot3/

CPU2 Slot5)

• One (1) PCI-Express 2.0 x4 in x8 slot (CPU2 Slot4)

Slots

Graphics

• Graphics Controller via ASpeed AST 2400 BMC

Network

• Dual Intel i350 1GBASE-T (10/100/1000 Mb/s) Ether-

net controllers for GLAN1-GLAN4 ports (X10DRC/i-

LN4+), or

• Dual Intel X540 10GBASE-T (100/1000/10000

Mb/s) Ethernet controllers for TLAN1-TLAN4 ports

(X10DRC/i-T4+)

• ASpeed 2400 Baseboard Controller (BMC) supports

IPMI_LAN 2.0

1-8

X10DRC/i-LN4+/-T4+ Motherboard User’s Manual

I/O Devices

SATA Connections

• SATA 3.0 Six (6) SATA 3.0 Ports support-

ed by Intel PCH (I-SATA 0-5),

Four (4) SATA 3.0 Ports support-

ed by Intel SCU (S-SATA 0-3)

• RAID 0, 1, 10 (from Intel PCH)

SAS Connections (for the X10DRC-LN4+/T4+)

• SAS 3.0 Eight (8) SAS Connections 0-3,

4-7 from the LSI 3108 controller

• RAID 0, 1, 5, 6, 10, 50, and 60 (from

the LSI SAS controller with

optional SuperCAP for battery

backup. See Note 1 next page.)

IPMI 2.0

• IPMI 2.0 supported by ASpeed AST 2400

Serial (COM) Port

• One (1) Fast UART 16550 Port

• One (1) Header

Peripheral
Devices

USB Devices

• Two (2) USB 2.0 ports (USB 0/1) and two (2) USB

3.0 ports (USB 4/5) on the I/O backpanel

• One (1) internal USB 2.0 header for two (2) USB

connections for front panel support (USB 2/3)

• One (1) internal USB 3.0 header for two (2) USB

connections for front panel support (USB 7/8)

• One (1) USB 3.0 Type A connector (USB 6)

BIOS

• 16 MB SPI AMI BIOS

®

SM Flash UEFI BIOS

• APCI 2.3, ACPI 2.0/3.0/4.0, USB Keyboard, Plug &

Play (PnP) and SMBIOS 2.3

Power

• ACPI Power Management

Management

• Main switch override mechanism

• Power-on mode for AC power recovery

• Intel

®

Intelligent Power Node Manager 3.0 (Avail-

able when the Supermicro Power Manager (SPM)

is installed and special power supply used. See

Page 1-14.)

• Management Engine (ME)

Chapter 1: Overview

1-9

CPU

CPU Monitoring

Monitoring

• Onboard voltage monitoring for +3.3V, 3.3V Standby,

+5V, +5V Standby, +12V, CPU core, memory, chipset,

BMC, and battery voltages

• CPU/System overheat LED and control

• CPU Thermal Trip support

• Status Monitor for Speed Control

• Status Monitor for On/Off Control

• CPU Thermal Design Power (TDP): support up to

145W (See Note 2 below)

Fan Control

• Fan status monitoring via IPMI connections

• Dual Cooling Zone

• Low noise fan speed control

• Pulse Width Modulation (PWM) fan contorl

System
Management

• PECI (Platform Environment Conguration Interface)

2.0 support

• UID (Unit Identication)/Remote UID

• System resource alert via SuperDoctor 5

• SuperDoctor® 5, Watch Dog, NMI

• Chassis Intrusion Header and Detection

Dimensions

• 13.68" (L) x 13.05" (W) (347.47 mm x 331.47 mm)

Note 1: For SAS is supported by the onboard LSI3108 controller, and is

available on the X10DRC-LN4+/T4+ only)

Note 2: CPU Maximum Thermal Design Power (TDP) is subject to chassis

and heatsink cooling restrictions. For proper thermal management, please

check the chassis and heatsink specications for proper CPU TDP sizing.

Note 3: For IPMI Conguration Instructions, please refer to the Embedded

IPMI Conguration User's Guide available @ http://www.supermicro.com/

support/manuals/.

1-10

X10DRC/i-LN4+/-T4+ Motherboard User’s Manual

System Block Diagram

Note 1: This is a general block diagram and may not exactly represent

the features on your motherboard. See the Motherboard Features pages

for the actual specications of each motherboard.

Note 2: Both CPU’s need to be installed for full access the PCI-E slots and

on-board controllers. See the attached block diagram to determine which

PCI-E slots or devices may be impacted.

P0P0P1

P1

D

D

E

E

E

F

F

F

G

G

G

H

H

H

PCI-E x16 SLOT 3

PCI-E

SATA #1

SATA #2

DDR4 DIMM

SATA #3

SATA #4

SATA #5

SATA #6

USB 3.0

SATA

DDR4 DIMM

#3

#2

#1

DDR4 DIMM

G

A

LPC

USB 3.0

LAN

I350/

X540/

SAGEVILL

ABD

BC

PROCESSOR1

A

C

PROCESSOR2

A

B

C

QPI

#1

DDR4 DIMM

#2

#3

DDR4 DIMM

PCI-E x8 SLOT 4

DDR4 DIMM

x16

LSI

3108

x8

x8 (0-7)

TPM HDR

PCH 612

QPI

x16

DMI

VGA BMC

VGA
CONN

AST2400

DDR 3

DDR4 DIMM

PHY1

LAN

RTL8211

B

PCI-E x8 SLOT 6

PCI-E x16 SLOT 5

DDR4 DIMM

PCI-E x8 SLOT 2

PCI-E X1 G2

D

C

H

F

E

#1

#2

#3

#1

#2

#3

#1

#2

#3

#1

#2

#3

#1

#2

#3

#1

#2

#3

SYSTEM

BIOS

SPI

SPI

COM

SATA #7

SATA #8

SATA #9

SATA #10

BMC BOOT FLASH

1

2

3

4

5

USB

LAN

x8 (8-15)

9.6G

6GB/s

x8

x16

x16

PCI-E x8 SLOT 1

x8

x8

x8

SPI

USB2.0

USB2.0

I350/

X540/

SAGEVILL

Gen2 x4

x16

Gen2 x4

USB 2.0

1

2

3

4

5

6

USB

USB 2.0

9

8

7

x8

x16

(7-0)

(15-8)

(15-0)

RJ45 RJ45

RJ45

RJ45

PE2 PE3

PE1

DM1

PE2

PE3 PE1

DM1

Chapter 1: Overview

1-11

1-2 Processor and Chipset Overview

Built upon the functionality and capability of the Intel E5-2600v3 Series Proces-

sors (Socket R3) and the Intel C612 PCH, the X10DRC/i-LN4+/-T4+ motherboard

provides the b est b alanced soluti on of p erformance, powe r ef cienc y, and features

to address the diverse needs of next-generation data server platforms.

With support of new Intel Microarchitecture 22nm Process Technology, the
X10DRC/i-LN4+/-T4+ dramatically increases system performance for a multitude

of server applications.

The PCH C612 chip provides Enterprise SMbus and MCTP support, including the

following features:

•DDR4 288-pin memory support on Socket R3

•Support for MCTP Protocol and ME

•Support of SMBus speeds of up to 1 MHz for BMC connectivity

•Improved I/O capabilities to high-storage-capacity congurations

•SPI Enhancements

•Intel® Node Manager 3.0 support (See Note below.)

•BMC supports remote management, virtualization, and the security package

for enterprise platforms

Note: Node Manager 3.0 support is dependent on the power supply used

in the system.

1-12

X10DRC/i-LN4+/-T4+ Motherboard User’s Manual

1-3 Special Features

Recovery from AC Power Loss

The Basic I/O System (BIOS) provides a setting that determines how the system will

respond when AC power is lost and then restored to the system. You can choose for

the system to remain powered off (in which case you must press the power switch

to turn it back on), or for it to automatically return to the power-on state. See the

Advanced BIOS Setup section for this setting. The default setting is Last State.

1-4 System Health Monitoring

This section describes the features of system health monitoring of the motherboard.

This motherboard has an onboard BaseBoard Management Controller (BMC) that

supports system health monitoring. An onboard voltage monitor will scan the follow-

ing onboard voltages continuously: +3.3V, 3.3V Standby, +5V, +5V Standby, +12V,

CPU core, memory, chipset, BMC, and battery voltages. Once a voltage becomes

unstable, a warning is given, or an error message is sent to the screen. The user

can adjust the voltage thresholds inside the BMC Web GUI to dene the sensitivity

of the voltage monitor.

Fan Status Monitor with Firmware Control

System health monitoring support provided by the BMC controller can check the

RPM status of a cooling fan. The onboard CPU and chassis fans are controlled by

IPMI Thermal Management.

Environmental Temperature Control

System health sensors monitor temperatures and voltage settings of onboard

processors and the system in real time via the IPMI interface. Whenever the tem-

perature of the CPU or the system exceeds a user-dened threshold, system/CPU

cooling fans will be turned on to prevent the CPU or the system from overheating.

Note: To avoid possible system overheating, please be sure to provide

adequate airow to your system.

System Resource Alert

This feature is available when used with SuperDoctor 5. SuperDoctor 5 is used

to notify the user of certain system events. For example, you can congure

SuperDoctor 5 to provide you with warnings when the system temperature, CPU

temperatures, voltages, and fan speeds go beyond a predened range.

Chapter 1: Overview

1-13

1-5 ACPI Features

ACPI stands for Advanced Conguration and Power Interface. The ACPI specica-

tion denes a exible and abstract hardware interface that provides a standard

way to integrate power management features throughout a system, including its

hardware, operating system and application software. This enables the system to

automatically turn on and off peripherals such as CD-ROMs, network cards, hard

disk drives and printers.

In addition to operating system-directed power management, ACPI also provides

a generic system event mechanism for Plug and Play, and an operating system-

independent interface for conguration control. ACPI leverages the Plug and Play

BIOS data structures, while providing a processor architecture-independent imple-

mentation that is compatible with Windows 8/R2, and Windows 2012/R2 Operating

Systems.

1-6 Power Supply

As with all computer products, a stable power source is necessary for proper and

reliable operation. It is even more important for processors that have high CPU

clock rates.

The X10DRC/i-LN4+/-T4+ motherboard accommodates 24-pin ATX power sup-

plies. Although most power supplies generally meet the specications required by

the CPU, some are inadequate. In addition, two 8-pin power connections are also

required to ensure adequate power supply to the system.

Warning! To avoid damaging the power supply or the motherboard, be sure to use

a power supply that contains a 24-pin and two 8-pin power connectors. Be sure to

connect the power supply to the 24-pin power connector (J24), and two 8-pin power

connectors (JPWR1, JPWR2) on the motherboard. Failure in doing so may void the

manufacturer warranty on your power supply and motherboard.

It is strongly recommended that you use a high quality power supply that meets ATX

power supply Specication 2.02 or above. It must also be SSI compliant. (For more

information, please refer to the website at http://www.ssiforum.org/). Additionally, in

areas where noisy power transmission is present, you may choose to install a line

lter to shield the computer from noise. It is recommended that you also install a

power surge protector to help avoid problems caused by power surges.

1-14

X10DRC/i-LN4+/-T4+ Motherboard User’s Manual

1-7 Advanced Power Management

The following new advanced power management features are supported by this

motherboard:

Intel® Intelligent Power Node Manager (NM) (Available
when the Supermicro Power Manager [SPM] is Installed)

The Intel® Intelligent Power Node Manager 3.0 (IPNM) provides your system with

real-time thermal control and power management for maximum energy efciency.

Although IPNM Specication Version 2.0/3.0 is supported by the BMC (Baseboard

Management Controller), your system must also have IPNM-compatible Manage-

ment Engine (ME) rmware installed to use this feature.

Note: IPNM 2.0/3.0 support is dependent on the power supply used in

the system.

Management Engine (ME)

The Management Engine, which is an ARC controller embedded in the PCH, pro-

vides Server Platform Services (SPS) to your system. The services provided by

SPS are different from those provided by the ME on client platforms.

Chapter 2: Installation

2-1

Chapter 2

Installation

2-1 Standardized Warning Statements

The following statements are industry-standard warnings, provided to warn the user

of situations which have the potential for bodily injury. Should you have questions or

experience difculty, contact Supermicro's Technical Support department for assis-

tance. Only certied technicians should attempt to install or congure components.

Read this section in its entirety before installing or conguring components in the

Supermicro chassis.

Battery Handling

Warnung

Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die

Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.

Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.

Warning!

There is a danger of explosion if the battery is replaced incorrectly. Replace the

battery only with the same or equivalent type recommended by the manufacturer.

Dispose of used batteries according to the manufacturer's instructions

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。 交換する電池はメー
カーが推奨する型、または同等のものを使用下さい。 使用済電池は製造元の指示に従
って処分して下さい。

警告

电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更

换原有电池。请按制造商的说明处理废旧电池。

警告

電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有

電池。請按照製造商的說明指示處理廢棄舊電池。

2-2

X10DRC/i-LN4+/-T4+ Motherboard User’s Manual

Attention

Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer

que par une pile de type semblable ou équivalent, recommandée par le fabricant.

Jeter les piles usagées conformément aux instructions du fabricant.

¡Advertencia!

Existe peligro de explosión si la batería se reemplaza de manera incorrecta. Re-

emplazar la batería exclusivamente con el mismo tipo o el equivalente recomen-

dado por el fabricante. Desechar las baterías gastadas según las instrucciones

del fabricante.

!הרהזא

תנכס תמייקץוציפ .הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי

גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ.

תוללוסה קוליס תושמושמה עצבל שי .ןרציה תוארוה יפל









경고!

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일
하거나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다. 제조사
의 안내에 따라 사용된 배터리를 처리하여 주십시오.

Waarschuwing

Er is ontplofngsgevaar indien de batterij verkeerd vervangen wordt. Vervang de

batterij slechts met hetzelfde of een equivalent type die door de fabrikant aan-

bevolen wordt. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften

afgevoerd te worden.

Chapter 2: Installation

2-3

Product Disposal

Warning!

Ultimate disposal of this product should be handled according to all national laws

and regulations.

製品の廃棄

この製品を廃棄処分する場合、国の関係する全ての法律・条例に従い処理する必要が
ありま す。

警告
本产品的废弃处理应根据所有国家的法律和规章进行。

警告
本產品的廢棄處理應根據所有國家的法律和規章進行。

Warnung

Die Entsorgung dieses Produkts sollte gemäß allen Bestimmungen und Gesetzen

des Landes erfolgen.

¡Advertencia!

Al deshacerse por completo de este producto debe seguir todas las leyes y regla-

mentos nacionales.

Attention

La mise au rebut ou le recyclage de ce produit sont généralement soumis à des

lois et/ou directives de respect de l'environnement. Renseignez-vous auprès de

l'organisme compétent.

רצומה קוליס

!הרהזא

ו תויחנהל םאתהב תויהל בייח הז רצומ לש יפוס קוליס.הנידמה יקוח

2-4

X10DRC/i-LN4+/-T4+ Motherboard User’s Manual

2-2 Static-Sensitive Devices

Electrostatic Discharge (ESD) can damage electronic com ponents. To avoid dam-

aging your system board, it is important to handle it very carefully. The following

measures are generally sufcient to protect your equipment from ESD.

Precautions

•Use a grounded wrist strap designed to prevent static discharge.

•Touch a grounded metal object before removing the board from the antistatic

bag.

•Handle the motherboard by its edges only; do not touch its components, periph-

eral chips, memory modules or gold contacts.

•When handling chips or modules, avoid touching their pins.

•Put the motherboard and peripherals back into their antistatic bags when not

in use.

•For grounding purposes, make sure that your system chassis provides excellent

conductivity between the power supply, the case, the mounting fasteners and

the motherboard.

Unpacking

The motherboard is shipped in antistatic packaging to avoid static damage.

When unpacking the motherboard, make sure that the person handling it is static

protected.

Waarschuwing

De uiteindelijke verwijdering van dit product dient te geschieden in overeenstemming

met alle nationale wetten en reglementen.

 

경고!

이 제품은 해당 국가의 관련 법규 및 규정에 따라 폐기되어야 합니다.

Chapter 2: Installation

2-5

IPMI CODE

SAS CODE

SAN MAC

BIOS
LICENSE

MAC CODE

BAR CODE

X10DRC/i-LN4+(-T4+)

Rev. 1.01

2-3 Motherboard Installation

All motherboards have standard mounting holes to t different types of chassis.

Make sure that the locations of all the mounting holes for both motherboard and

chassis match. Although a chassis may have both plastic and metal mounting fas-

teners, metal ones are highly recommended because they ground the motherboard

to the chassis. Make sure that the metal standoffs click in or are screwed in tightly.

Then use a screwdriver to secure the motherboard onto the motherboard tray.

Tools Needed

•Phillips Screwdriver

•Pan head screws (11 pieces)

•Standoffs (11 pieces, if needed)

Location of Mounting Holes

There are eleven (11) mounting holes on this motherboard indicated by the arrows.

Caution: 1) To avoid damaging the motherboard and its components, please do

not use a force greater than 8 lb/inch on each mounting screw during motherboard

installation. 2) Some components are very close to the mounting holes. Please take

precautionary measures to prevent damage to these components when installing the

motherboard to the chassis.

2-6

X10DRC/i-LN4+/-T4+ Motherboard User’s Manual

Installing the Motherboard

Note: Always connect the power cord last, and always remove it before

adding, removing or changing any hardware components.

1. Install the I/O shield into the chassis.

2. Locate the mounting holes on the motherboard.

3. Locate the matching mounting holes on the chassis. Align the mounting holes

on the motherboard against the mounting holes on the chassis.

4. Install standoffs in the chassis as needed.

5. Install the motherboard into the chassis carefully to avoid damaging mother-

board components.

6. Using the Phillips screwdriver, insert a Pan head #6 screw into a mounting

hole on the motherboard and its matching mounting hole on the chassis.

7. Repeat Step 5 to insert #6 screws into all mounting holes.

8. Make sure that the motherboard is securely placed in the chassis.

Note: Images displayed are for illustration only. Your chassis or compo-

nents might look different from those shown in this manual.

Chapter 2: Installation

2-7

OPEN 1st

WARNING!

2-4 Processor and Heatsink Installation

Warning: When handling the processor package, avoid placing direct pressure on

the label area. Also, improper CPU installation or socket/pin misalignment can cause

serious damage to the CPU or the motherboard that will require RMA repairs. Be sure

to read and follow all instructions thoroughly before installing your CPU and heatsink.

Notes:

•Always connect the power cord last, and always remove it before adding, re-

moving or changing any hardware components. Make sure that you install the

processor into the CPU socket before you install the CPU heatsink.

•If you buy a CPU separately, make sure that you use an Intel-certied multi-

directional heatsink only.

•Make sure to install the motherboard into the chassis before you install the

CPU heatsink.

•When receiving a motherboard without a processor pre-installed, make sure that

the plastic CPU socket cap is in place and none of the socket pins are bent;

otherwise, contact your retailer immediately.

•Refer to the Supermicro website for updates on CPU support.

Press down on

the

Load Lever

labeled 'Open 1st'.

Installing the LGA2011 Processor

1. There are two load levers on the LGA2011 socket. To open the socket cover,

rst press and release the load lever labeled 'Open 1st'.

OPEN 1st

WARNING!

1 2

Note: All graphics, drawings and pictures shown in this manual are for il-

lustration only. The components that came with your machine may or may

not look exactly the same as those shown in this manual.

2-8

X10DRC/i-LN4+/-T4+ Motherboard User’s Manual

Gently push the
lever down to pop
the load plate open.

2. Press the second load lever labeled 'Close 1st' to release the load plate that

covers the CPU socket from its locking position.

3. With the lever labelled 'Close 1st' fully retracted, gently push down on the

lever labelled 'Open 1st' to open the load plate. Lift the load plate to open it

completely.

OPEN 1st

WARNING!

OPEN 1st

WARNING!

1

2

Press down on the

Load

Lever

labeled

'Close 1st'

WARNING!

OPEN 1st

WARNING!

1

Pull the lever away
from the socket

2

Note: All graphics, drawings and pictures shown in this manual are for il-

lustration only. The components that came with your machine may or may

not look exactly the same as those shown in this manual.