Supermicro MicroBlade MBI-6219G-T8HX, MicroBlade MBI-6119G-T8HX User Manual

MBI-6219G-T8HX

MBI-6119G-T8HX

MicroBlade™ Module

User’s Manual

Revison 1.0a

MBI-6219G-T8HX /MBI-6119G-T8HX Blade Server Module User’s Manual

ii

The information in this User’s Manual has been carefully reviewed and is believed to be accurate. The
vendor assumes no responsibility for any inaccuracies that may be contained in this document, makes no
commitment to update or to keep current the information in this manual, or to notify any person or
organization of the updates. Please Note: For the most up-to-date version of this manual, please see

our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product described
in this manual at any time and without notice. This product, including software and documentation, is the
property of Supermicro and/or its licensors, and is supplied only under a license. Any use or reproduction
of this product is not allowed, except as expressly permitted by the terms of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,
SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE
THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE,
SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF
REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE,
SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa Clara
County in the State of California, USA. The State of California, County of Santa Clara shall be the
exclusive venue for the resolution of any such disputes. Super Micro's total liability for all claims will not
exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the manufacturer’s instruction manual, may cause harmful interference with radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference,
in which case you will be required to correct the interference at your own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate warning
applies only to products containing CR (Manganese Dioxide) Lithium coin cells. Perchlorate
Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate for further
details.

WARNING: HANDLING OF LEAD SOLDER MATERIALS USED IN THIS PRODUCT MAY
EXPOSE YOU TO LEAD, A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO
CAUSE BIRTH DEFECTS AND OTHER REPRODUCTIVE HARM.

Manual Revison 1.0a

Release Date: September 6, 2017

Unless you request and receive written permission from Super Micro Computer, Inc., you may not copy
any part of this document.

Information in this document is subject to change without notice. Other products and companies referred
to herein are trademarks or registered trademarks of their respective companies or mark holders.

Copyright © 2016 by Super Micro Computer, Inc.
All rights reserved.

Printed in the United States of America

iii

:

Preface

About this Manual

This manual is written for professional system integrators, Information Technology
professionals, service personnel and technicians. It provides information for the
installation and use of both the Supermicro MBI-6219G-T8HX and
MBI-6119G-T8HXMicroBlade modules. Installation and maintenance should be
performed by experienced professionals only.

Manual Organization

Chapter 1: Introduction

The first chapter provides a checklist of the main components included with the
MicroBlade modules and describes their main features.

Chapter 2: System Safety

You should familiarize yourself with this chapter for a general overview of safety
precautions that should be followed when installing and servicing the MicroBlade
modules.

Chapter 3: Setup and Installation

Refer to this chapter for details on installing the MicroBlade modules into the MicroBlade
chassis. Other sections cover the installation and placement of memory modules and
the installation of hard disk drives into the blade module.

Chapter 4: Blade Module Features

This chapter coves features and component information about the MicroBlade modules.
Included here are descriptions and information for mainboard components, connectors,
LEDs and other features of the blade module.

Chapter 5: BIOS

BIOS setup is covered in this chapter for the MicroBlade modules.

Appendix A: BIOS POST Codes

BIOS POST Codes for the MicroBlade modules are explained in this appendix.

MBI-6219G-T8HX /MBI-6119G-T8HX Blade Server Module User’s Manual

iv

Notes

v

Table of Contents

Chapter 1 Introduction.......................................................................1-1

1-1 Overview.............................................................................................1-1

1-2 Blade Module Features....................................................................1-2

Blade Enclosures ....................................................................................1-3

Processors ..............................................................................................1-3

Memory ...................................................................................................1-3

Storage ...................................................................................................1-4

RAID .......................................................................................................1-4

Density....................................................................................................1-4

1-3 Contacting Supermicro.....................................................................1-5

Chapter 2 Standardized Warning Statements.....................2-1

2-1 About Standardized Warning Statements .....................................2-1

Warning Definition...................................................................................2-1

Installation Instructions ...........................................................................2-3

Circuit Breaker ........................................................................................2-4

Power Disconnection Warning................................................................2-5

Equipment Installation.............................................................................2-6

Restricted Area .......................................................................................2-7

Battery Handling .....................................................................................2-9

Redundant Power Supplies ..................................................................2-10

Backplane Voltage ................................................................................2-11

Comply with Local and National Electrical Codes.................................2-12

Product Disposal...................................................................................2-13

Hot Swap Fan Warning.........................................................................2-14

Power Cable and AC Adapter ..............................................................2-15

Hot Swap Fan Warning ........................................................................2-17

Chapter 3 Setup and Installation.................................................3-1

3-1 Overview.............................................................................................3-1

3-2 Installing MicroBlade Modules ........................................................3-1

Powering Up a MicroBlade Module Unit .................................................3-1

Powering Down a MicroBlade Module Unit.............................................3-1

Removing a MicroBlade Module Unit from the Enclosure ......................3-2

Installing a Blade Unit into the Enclosure ...............................................3-2

3-3 Onboard Battery Installation............................................................3-3

MBI-6219G-T8HX /MBI-6119G-T8HX Blade Server Module User’s Manual

vi

3-4 Memory Installation...........................................................................3-4

Populating Memory Slots ........................................................................3-4

Memory Support .....................................................................................3-4

DIMM Installation ....................................................................................3-5

3-5 Hard Disk Drive Installation .............................................................3-7

3-6 Installing the Operating System......................................................3-7

Installing with a SATA-DOM Module ....................................................... 3-7

Installing via PXE Boot............................................................................3-7

Installing via Virtual Media (Drive Redirection) .......................................3-7

Chapter 4 MicroBlade Module Features .................................4-1

4-1 Control Panel .....................................................................................4-2

Power Button ..........................................................................................4-3

LED Indicators ........................................................................................4-3

4-2 Serverboard .......................................................................................4-4

Jumpers ..................................................................................................4-6

CMOS Clear............................................................................................4-6

4-3 Blade Unit Components...................................................................4-7

Memory Support .....................................................................................4-8

Hard Disk Drives .....................................................................................4-9

Blade Power Consumption Page............................................................4-9

Chapter 5 BIOS.......................................................................................5-1

5-1 Introduction.........................................................................................5-1

System BIOS ..........................................................................................5-1

How To Change the Configuration Data ................................................. 5-1

Starting the Setup Utility .........................................................................5-1

5-2 BIOS Updates....................................................................................5-2

Flashing a BIOS using a Floppy Image File............................................5-2

5-3 Running Setup ...................................................................................5-2

5-4 Main BIOS Setup...............................................................................5-3

5-5 Advanced Setup ................................................................................5-5

5-6 Event Logs Setup............................................................................5-17

5-7 IPMI Setup........................................................................................5-18

5-8 Security .............................................................................................5-19

5-9 Boot ...................................................................................................5-19

5-10 Save & Exit.....................................................................................5-20

vii

:

Appendix A AMI UEFI BIOS POST Codes..............................A-1

A-1 Checkpoint Ranges..........................................................................A-1

A-2 Standard Checkpoints......................................................................A-2

A-3 OEM-Reserved Checkpoint Ranges .............................................A-9

MBI-6219G-T8HX /MBI-6119G-T8HX Blade Server Module User’s Manual

viii

Notes

1-1

Chapter 1: Introduction

Chapter 1

Introduction

1-1 Overview

This user’s manual covers the MBI-6219G-T8HX/MBI-6119G-T8HX MicroBlade module.
This MicroBlade module is a compact self-contained server that connects into a
pre-cabled enclosure that provides power, cooling, management and networking
functions. One enclosure for the MBI-6219G-T8HX/MBI-6119G-T8HX MicroBlade
module can hold twenty-eight blade units.

In this manual, “blade system” refers to the entire system (including the enclosure and
blades units), “blade”, “MicroBlade” or “blade unit” refers to a single MicroBlade module
and “blade enclosure” is the chassis that the MicroBlades, power supplies and
MicroBlade modules are housed within.

Please refer to our web site for information on operating systems that have been
certified for use with the MicroBlade (http://www.supermicro.com/products/nfo/

microblade.cfm).

Note: For your system to work properly, please follow the links below to download all
necessary drivers/utilities and the user’s manual for your server.

• Supermicro product manuals: http://www.MicroBlade.com/support/manuals/

• Product drivers and utilities: ftp://ftp.supermicro.com

• Product safety information: http://www.supermicro.com/about/policies/

safety_information.cfm

• If you have any questions, please contact our support team at:

[e-mail]

Note: A complete list of safety warnings is provided on the Supermicro web site at

http://www.supermicro.com/about/policies/safety_information.cfm.

MBI-6219G-T8HX/MBI-6119G-T8HX MicroBlade Module User’s Manual

1-2

1-2 Blade Module Features

Table 1-1 lists the main features of the MBI-6219G-T8HX/MBI-6119G-T8HX MicroBlade

module. See the proceeding section for components typically included in a blade system
and other optional components. Specific details for the MBI-6219G-T8HX/
MBI-6119G-T8HX MicroBlade module are found in Chapter 4: "MicroBlade Module

Features" on page 4-1. The only difference between the two MicroBlade modules is that

the MBI-6119G-T8HX MicroBlade module has one node and the B2SS1-H-MTF
serverboard, while the MBI-6219G-T8HXMicroBlade module has two nodes and the
B2SS2-H-MTF serverboard.

Table 1-1. MBI-6219G-T8HX/MBI-6119G-T8HX MicroBlade Module

Specification Features

Serverboard

B2SS1-H-MTF (MBI-6119G-T8HX), B2SS2-H-MTF (MBI-6219G-T8HX)/
(proprietary form factor)

Blade System Enclosures

See the Blade Enclosures section below for a full list of MicroBlade
enclosures.

Chassis Specifications

Chassis Dimensions (HxWxD): 1.2" x 4.94" x 23.2" (30.48-mm x

125.476-mm x 589.28-mm), Gross Weight: 7.5 lbs (3.4 kg)

Processors

One (1) or Two (2) Intel® Xeon® E3-1585 V5 embedded processor in an
FCBGA1440 socket on the serverboard. See Processors section below for
details.

Chipset Intel C236

BIOS 128 MB SPI Flash EEPROM with AMI® BIOS

Memory Capacity

Supports up to 32 GB SODIMM DDR4 2133 MHz speed and 16 GB size
SODIMM memory in two (2) FCBGA1440 DIMM sockets

Hard Drive Bays

The blade module supports one (1) 2.5" SATA3 HDD/SSD disk drive per
node. Additionally, two (2) M.2 and one (1) SATA-DOM connectors are
also available per node.

1-3

Chapter 1: Introduction

Blade Enclosures

The MBI-6219G-T8HX/MBI-6119G-T8HX MicroBlade module can be mounted in any of
the following MicroBlade Enclosures:

•6U:

• MBE-628E-416

• MBE-628E-420

• MBE-628E-816

• MBE-628E-820(D)

• MBE-628EB-422

• MBE-628EB-622

• MBE-628EB-822

•3U:

• MBE-314E-420(D)

• MBE-314E-220(D)

• MBE-314E-416

Processors

The MBI-6219G-T8HX/MBI-6119G-T8HX MicroBlade module supports the E3-1585 V5
series processor in an FCBGA1440 socket. The MBI-6219G-T8HX supports two
processors while the MBI-6119G-T8HX supports only one processor

Refer to the Supermicro web site for a complete listing of supported processors (http://

www.supermicro.com/products/microblade). Please note that you will need to check the

detailed specifications of a particular blade module for a list of the CPUs it supports.

Details on installation of the processor into the MBI-6219G-T8HX/MBI-6119G-T8HX
MicroBlade module are found in Chapter 3: " Setup and Installation" on page 3-1.

Memory

Each of the MBI-6219G-T8HX/MBI-6119G-T8HX MicroBlade module’s nodes have two
(2) FCBGA1440 DIMM sockets that can support up to 32 GB SODIMM of DDR4 2133
MHz speed, 16 GB size SODIMM memory. Memory is interleaved, which requires both
modules to be of the same size and speed.

Please refer to the Supermicro web site for a list of supported memory http://

www.supermicro.com/products/microblade The detailed specifications for a blade

module will contain a link to a list of recommended memory sizes and manufacturers.

Details on installation of memory modules into the MBI-6219G-T8HX/MBI-6119G-T8HX
MicroBlade module are found in Chapter 3: " Setup and Installation" on page 3-1.

MBI-6219G-T8HX/MBI-6119G-T8HX MicroBlade Module User’s Manual

1-4

Storage

The MBI-6219G-T8HX/MBI-6119G-T8HX MicroBlade module has one (1) 2.5" SATA3
HDD/SSD for an internally mounted drive per node. Additionally, two (2) M.2 and one (1)
SATA-DOM connectors are available that can be used for connection to drives for
storage or for installation of the node’s operating system for each node. See Chapter 3:

" Setup and Installation" on page 3-1 for storage installation details.

RAID

The MBI-6219G-T8HX/MBI-6119G-T8HX MicroBlade module has only one hard drive
per node, so no RAID array is possible.

Density

A maximum of twenty-eight blade modules may be installed into a single blade
enclosure. Each blade enclosure is a 6U form factor, so a standard 42U rack may
accommodate up to seven enclosures with 196 blade modules, the equivalent of 392 1U
servers. With the inclusion of up to fourteen CMM modules and up to twenty-eight
Gigabit Ethernet switches this would occupy up to 434U space in a conventional 1U
server configuration.

1-5

Chapter 1: Introduction

1-3 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: [phone]

Fax: [phone]

Email:

[e-mail] (General Information)

[e-mail] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

‘s-Hertogenbosch, The Netherlands

Tel: [phone]

Fax: [phone]

Email:

[e-mail] (General Information)

[e-mail] (Technical Support)

[e-mail] (Customer Support)

Asia-Pacific

Address: Super Micro Computer, Inc.

3F, No. 150, Jian 1st Rd.

Zhonghe Dist., New Taipei City 23511

Taiwan (R.O.C)

Tel: [phone]

Fax: [phone]

Web Site: www.supermicro.com.tw

Technical Support:

Email: [e-mail]

Tel: [phone]

MBI-6219G-T8HX/MBI-6119G-T8HX MicroBlade Module User’s Manual

1-6

2-1

Chapter 2: Standardized Warning Statements

Chapter 2

Standardized Warning Statements

2-1 About Standardized Warning Statements

The following statements are industry standard warnings, provided to warn the user of
situations which have the potential for bodily injury. Should you have questions or
experience difficulty, contact Supermicro's Technical Support department for assistance.
Only certified technicians should attempt to install or configure components.

Read this appendix in its entirety before installing or configuring components in the
Supermicro chassis

These warnings may also be found on our web site at http://

www.supermicro.com/about/policies/safety_information.cfm.

Warning Definition

Warning!

This warning symbol means danger. You are in a situation that could cause

bodily injury. Before you work on any equipment, be aware of the hazards
involved with electrical circuitry and be familiar with standard practices for preventing
accidents.

警告の定義

この警告サインは危険を意味します。

人身事故につながる可能性がありますので、いずれの機器でも動作させる前に、

電気回路に含まれる危険性に注意して、標準的な事故防止策に精通して下さい。

此警告符号代表危险。

您正处于可能受到严重伤害的工作环境中。在您使用设备开始工作之前，必须充分意识到
触电的危险，并熟练掌握防止事故发生的标准工作程序。请根据每项警告结尾的声明号码
找到此设备的安全性警告说明的翻译文本。

此警告符號代表危險。

您正處於可能身體可能會受損傷的工作環境中。在您使用任何設備之前，請注意觸電的危
險，並且要熟悉預防事故發生的標準工作程序。請依照每一注意事項後的號碼找到相關的
翻譯說明內容。

MBI-6219G-T8HX/MBI-6119G-T8HX MicroBlade Module User’s Manual

2-2

Warnung

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu
Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren
elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen
vertraut. Suchen Sie mit der am Ende jeder Warnung angegebenen
Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de
manipular cualquier equipo, considere los riesgos de la corriente eléctrica y
familiarícese con los procedimientos estándar de prevención de accidentes. Al final de
cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en
el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES.

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation
pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un
équipement, soyez conscient des dangers liés aux circuits électriques et
familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents.
Pour prendre connaissance des traductions des avertissements figurant dans les
consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro
de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS.

안전을 위한 주의사항

경고 !

. ﻲﻓ ﻚﻧا نأ ﻦﻜﻤﯾ ﺔﻟﺎﺣ ﻲﻓ ﺐﺒﺴﺘﺗ ﺔﺑﺎﺻا ﺔﯾﺪﺴﺟ ﺰﻣﺮﻟا اﺬھ ﻲﻨﻌﯾ ﺮﻄﺧ !ﺮﯾﺬﺤﺗ

نأ ﻞﺒﻗ يأ ﻰﻠﻋ ﻞﻤﻌﺗ تاﺪﻌﻣ،ﻛﻢﻠﻋ ﻰﻠﻋ ﻦ ﻦﻋ ﺔﻤﺟﺎﻨﻟا ﺮطﺎﺨﻤﻟﺎﺑ ﺮﺋاوﺪﻟا

ﺔﯿﺋﺎﺑﺮﮭﻜﻟا

ﻛوﺔﯾارد ﻰﻠﻋ ﻦ رﺎﻤﻤﻟﺎﺑتﺎﺳ ﺔﯿﺋﺎﻗﻮﻟا ﻟ ﻊﻨﻤعﻮﻗو يأثداﻮﺣ

ﻢﻗر مﺪﺨﺘﺳا نﺎﯿﺒﻟا صﻮﺼﻨﻤﻟا ﺔﯾﺎﮭﻧ ﻲﻓ ﺮﯾﺬﺤﺗ ﻞﻛ رﻮﺜﻌﻠﻟ ﺎﮭﺘﻤﺟﺮﺗ

2-3

Chapter 2: Standardized Warning Statements

이 경고 기호는 위험이 있음을 알려 줍니다 . 작업자의 신체에 부상을 야기 할 수 있는
상태에 있게 됩니다 . 모든 장비에 대한 작업을 수행하기 전에 전기회로와 관련된 위험
요소들을 확인하시고 사전에 사고를 방지할 수 있도록 표준 작업절차를 준수해 주시기
바랍니다 .

해당 번역문을 찾기 위해 각 경고의 마지막 부분에 제공된 경고문 번호를 참조하십시오

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwings symbool betekent gevaar. U verkeert in een situatie die lichamelijk
letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich
bewust te zijn van de bij een elektrische installatie betrokken risico's en dient u op de
hoogte te zijn van de standaard procedures om ongelukken te voorkomen. Gebruik de
nummers aan het eind van elke waarschuwing om deze te herleiden naar de
desbetreffende locatie.

BEWAAR DEZE INSTRUCTIES

Installation Instructions

Warning!

Read the installation instructions before connecting the system to the power

source.

設置手順書

システムを電源に接続する前に、設置手順書をお読み下さい。

警告
将此系统连接电源前 , 请先阅读安装说明。
警告

將系統與電源連接前，請先閱讀安裝說明。

Warnung

Vor dem Anschließen des Systems an die Stromquelle die Installationsanweisungen
lesen.

¡Advertencia!

Lea las instrucciones de instalación antes de conectar el sistema a la red de
alimentación.

Attention

Avant de brancher le système sur la source d'alimentation, consulter les directives
d'installation.

אורקל שי רוקמל תכרעמה רוביח ינפל הנקתה תוארוה תאחתמ.

MBI-6219G-T8HX/MBI-6119G-T8HX MicroBlade Module User’s Manual

2-4

시스템을 전원에 연결하기 전에 설치 안내를 읽어주십시오 .

Waarschuwing

Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit.

Circuit Breaker

Warning!

This product relies on the building's installation for short-circuit (overcurrent)

protection. Ensure that the protective device is rated not greater than: 250 V,
20 A.

サーキット・ブレーカー

この製品は、短絡（過電流）保護装置がある建物での設置を前提としています。

保護装置の定格が 250V、20A を超えないことを確認下さい。

警告
此产品的短路 ( 过载电流 ) 保护由建筑物的供电系统提供 , 确保短路保护设备的额定电流
不大于 250V,20A。
警告

此產品的短路 ( 過載電流 ) 保護由建築物的供電系統提供 , 確保短路保護設備的額定電
流不大於 250V,20A。

Warnung

Dieses Produkt ist darauf angewiesen, dass im Gebäude ein Kurzschluss- bzw.
Überstromschutz installiert ist. Stellen Sie sicher, dass der Nennwert der
Schutzvorrichtung nicht mehr als: 250 V, 20 A beträgt.

¡Advertencia!

Este equipo utiliza el sistema de protección contra cortocircuitos (o sobrecorrientes) del
edificio. Asegúrese de que el dispositivo de protección no sea superior a: 250 V, 20 A.

Attention

Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit dépend
de l'installation électrique du local. Vérifiez que le courant nominal du dispositif de
protection n'est pas supérieur à :250 V, 20 A.

ﻟا تادﺎﺷرإ ﺮﻗاﺐﯿﻛﺮﺘ ﻞﯿﺻﻮﺗ ﻞﺒﻗ ﻰﻟإ مﺎﻈﻨﻟا ﺔﻗﺎﻄﻠﻟ رﺪﺼﻣ

לע ךמתסמ הז רצומנגהה תעינמל םינבמב תנקתומה יכ אדוול שי .ילמשח רצק

רצקה ינפמ ןגמה רישכמה ילמשחהמ רתוי אל אוה-250 V, 20 A

2-5

Chapter 2: Standardized Warning Statements

경고 !

이 제품은 전원의 단락 ( 과전류 ) 방지에 대해서 전적으로 건물의 관련 설비에 의존합니
다 . 보호장치의 정격이 반드시 250V( 볼트 ), 20A( 암페어 ) 를 초과하지 않도록 해야
합니다 .

Waarschuwing

Dit product is afhankelijk van de kortsluitbeveiliging (overspanning) van uw electrische
installatie. Controleer of het beveiligde aparaat niet groter gedimensioneerd is dan
220V, 20A.

Power Disconnection Warning

Warning!

The system must be disconnected from all sources of power and the power

cord removed from the power supply module(s) before accessing the chassis
interior to install or remove system components.

電源切断の警告

システムコンポーネントの取り付けまたは取り外しのために、シャーシー内部にアクセ

スするには、

システムの電源はすべてのソースから切断され、電源コードは電源モジュールから取り

外す必要があります。

警告

在你打开机箱并安装或移除内部器件前 , 必须将系统完全断电 , 并移除电源线。

警告

在您打開機殼安裝或移除內部元件前，必須將系統完全斷電，並移除電源線。

Warnung

Das System muss von allen Quellen der Energie und vom Netzanschlusskabel getrennt
sein, das von den Spg.Versorgungsteilmodulen entfernt wird, bevor es auf den
Chassisinnenraum zurückgreift, um Systemsbestandteile anzubringen oder zu
entfernen.

ﺞﺘﻨﻤﻟا اﺬھ ﻰﻠﻋ ﺪﻤﺘﻌﯾ تاﺪﻌﻣ ﺔﯾﺎﻤﺤﻟا ةﺮﯿﺼﻘﻟاﺮﺋاوﺪﻟا ﻦﻣ ﺎﮭﺘﯿﺒﺜﺗ ﻢﺗ ﻲﺘﻟا ﻲﻓ

ﻰﻨﺒﻤﻟا

20A, 250V : ﻦﻣ ﺪﻛﺄﺗ نأ ﻢﯿﯿﻘﺗ زﺎﮭﺠﻟا ﻟاﻲﺋﺎﻗﻮ ﺲﯿﻟ ﻦﻣ ﺮﺜﻛأ

MBI-6219G-T8HX/MBI-6119G-T8HX MicroBlade Module User’s Manual

2-6

¡Advertencia!

El sistema debe ser disconnected de todas las fuentes de energía y del cable eléctrico
quitado de los módulos de fuente de alimentación antes de tener acceso el interior del
chasis para instalar o para quitar componentes de sistema.

Attention

Le système doit être débranché de toutes les sources de puissance ainsi que de son
cordon d'alimentation secteur avant d'accéder à l'intérieur du chassis pour installer ou
enlever des composants de systéme.

경고 !

시스템에 부품들을 장착하거나 제거하기 위해서는 섀시 내부에 접근하기 전에 반드시
전원 공급장치로부터 연결되어있는 모든 전원과 전기코드를 분리해주어야 합니다 .

Waarschuwing

Voordat u toegang neemt tot het binnenwerk van de behuizing voor het installeren of
verwijderen van systeem onderdelen, dient u alle spanningsbronnen en alle
stroomkabels aangesloten op de voeding(en) van de behuizing te verwijderen.

Equipment Installation

Warning!

Only trained and qualified personnel should be allowed to install, replace, or

service this equipment.

機器の設置

トレーニングを受け認定された人だけがこの装置の設置、交換、またはサービスを許
可されています。

警告
只有经过培训且具有资格的人员才能进行此设备的安装、更换和维修。
警告

只有經過受訓且具資格人員才可安裝、更換與維修此設備。

יילמשח קותינ ינפמ הרהזא

!הרהזא

למשחה תורוקמ לכמ תכרעמה תא קתנל שי ריסהל שיו קפסהמ ילמשחה לבכ תא

נקתה ךרוצל זראמה לש ימינפה קלחל השיג ינפלת רסה ואת .םיביכר

ﻞﺼﻓ ﺐﺠﯾ مﺎﻈﻨﻟا ﻊﯿﻤﺟ ﻦﻣردﺎﺼﻣ ﺔﻗﺎﻄﻟا ﺔﻟازإو ءﺎﺑﺮﮭﻜﻟا ﻚﻠﺳ ﻦﻣ ةﺪﺣو داﺪﻣا

ﺔﻗﺎﻄﻟا ﻞﺒﻗ

ﻰﻟإ لﻮﺻﻮﻟا ﺔﯿﻠﺧاﺪﻟا ﻖطﺎﻨﻤﻟا ﻟﻞﻜﯿﮭﻠ ﺔﻟازإ وأ ﺖﯿﺒﺜﺘﻟ تﺎﻧﻮﻜﻣ زﺎﮭﺠﻟا

2-7

Chapter 2: Standardized Warning Statements

Warnung

Das Installieren, Ersetzen oder Bedienen dieser Ausrüstung sollte nur geschultem,
qualifiziertem Personal gestattet werden.

¡Advertencia!

Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo.

Attention

Il est vivement recommandé de confier l'installation, le remplacement et la maintenance
de ces équipements à des personnels qualifiés et expérimentés.

경고 !

훈련을 받고 공인된 기술자만이 이 장비의 설치 , 교체 또는 서비스를 수행할 수 있습니
다.

Waarschuwing

Deze apparatuur mag alleen worden geïnstalleerd, vervangen of hersteld door
geschoold en gekwalificeerd personeel.

Restricted Area

Warning!

This unit is intended for installation in restricted access areas. A restricted

access area can be accessed only through the use of a special tool, lock and
key, or other means of security. (This warning does not apply to workstations).

アクセス制限区域

このユニットは、アクセス制限区域に設置されることを想定しています。

アクセス制限区域は、特別なツール、鍵と錠前、その他のセキュリティの手段を用い
てのみ出入りが可能です。

警告
此部件应安装在限制进出的场所，限制进出的场所指只能通过使用特殊工具、锁和钥匙或
其它安全手段进出的场所。
警告

此裝置僅限安裝於進出管制區域，進出管制區域係指僅能以特殊工具、鎖頭及鑰匙或其
他安全方式才能進入的區域。

!הרהזא

שר דבלב ךמסומ תווצתא ףילחהל ,ןיקתהל יא .דויצה רובע תוריש תתל וא דויצה

ﻦﯿﺑرﺪﻤﻟاو و ﺐﯿﻛﺮﺘﻟلاﺪﺒﺘﺳا وأ ﺔﻣﺪﺧ زﺎﮭﺠﻟا اﺬھ ﺢﻤﺴﯾ نأ ﺐﺠﯾ ﻂﻘﻓ ﻦﯿﻠھﺆﻤﻟا ﻦﯿﻔظﻮﻤﻠﻟ

MBI-6219G-T8HX/MBI-6119G-T8HX MicroBlade Module User’s Manual

2-8

Warnung

Diese Einheit ist zur Installation in Bereichen mit beschränktem Zutritt vorgesehen. Der
Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und
Schlüssel oder einer sonstigen Sicherheitsvorkehrung möglich.

¡Advertencia!

Esta unidad ha sido diseñada para instalación en áreas de acceso restringido. Sólo
puede obtenerse acceso a una de estas áreas mediante la utilización de una
herramienta especial, cerradura con llave u otro medio de seguridad.

Attention

Cet appareil doit être installée dans des zones d'accès réservés. L'accès à une zone
d'accès réservé n'est possible qu'en utilisant un outil spécial, un mécanisme de
verrouillage et une clé, ou tout autre moyen de sécurité.

경고 !

이 장치는 접근이 제한된 구역에 설치하도록 되어있습니다 . 특수도구 , 잠금 장치 및 키
, 또는 기타 보안 수단을 통해서만 접근 제한 구역에 들어갈 수 있습니다 .

Waarschuwing

Dit apparaat is bedoeld voor installatie in gebieden met een beperkte toegang. Toegang
tot dergelijke gebieden kunnen alleen verkregen worden door gebruik te maken van
speciaal gereedschap, slot en sleutel of andere veiligheidsmaatregelen.

תתלבגומ השיג םע רוזא

!הרהזא

תרזעב תנתינ השיגה .השיג תלבגה םהב שיש םירוזאב הדיחיה תא ןיקתהל שי

.('דכו לוענמ ,חתפמ) דבלב החטבא ילכ

. ﺺﯿﺼﺨﺗ ةﺪﺣﻮﻟا هﺬھ ﻲﻓ ﺎﮭﺒﯿﻛﺮﺘﻟ ﻖطﺎﻨﻣ ةرﻮﻈﺤﻣ ﻢﺗ

ﺻﻮﻟا ﻦﻜﻤﯾﻰﻟإ لﻮ ﺔﻘﻄﻨﻣ ةرﻮﻈﺤﻣ ﻂﻘﻓ ماﺪﺨﺘﺳا لﻼﺧ ﻦﻣ ،ﺔﺻﺎﺧ ةادأ

وأ يأ ﻼﻟ ىﺮﺧأ ﺔﻠﯿﺳونﺎﻣﻷ حﺎﺘﻔﻣو ﻞﻔﻗ

2-9

Chapter 2: Standardized Warning Statements

Battery Handling

Warning!

There is the danger of explosion if the battery is replaced incorrectly. Replace

the battery only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer's instructions.

電池の取り扱い

電池交換が正しく行われなかった場合、破裂の危険性があります。交換する電池は
メーカーが推奨する型、または同等のものを使用下さい。使用済電池は製造元の指示
に従って処分して下さい。

警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更换原有
电池。请按制造商的说明处理废旧电池。
警告

電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有電
池。請按照製造商的說明指示處理廢棄舊電池。

Warnung

Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die
Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp.
Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.

Attention

Danger d'explosion si la pile n'est pas remplacée correctement. Ne la remplacer que par
une pile de type semblable ou équivalent, recommandée par le fabricant. Jeter les piles
usagées conformément aux instructions du fabricant.

¡Advertencia!

Existe peligro de explosión si la batería se reemplaza de manera incorrecta.
Reemplazar la batería exclusivamente con el mismo tipo o el equivalente recomendado
por el fabricante. Desechar las baterías gastadas según las instrucciones del fabricante.

경고 !

!הרהזא

תנכס תמייקץוציפ .הניקת אל ךרדב הפלחוהו הדימב הללוסה לש ףילחהל שי

גוסב הללוסה תא מ םאותה תרבחלמומ ןרציתצ.

תוללוסה קוליס תושמושמה עצבל שי .ןרציה תוארוה יפל

ﺮﻄﺧ كﺎﻨھ ﻦﻣ لاﺪﺒﺘﺳا ﺔﻟﺎﺣ ﻲﻓ رﺎﺠﻔﻧا ﺔﯾرﺎﻄﺒﻟا ﺔﺤﯿﺤﺻ ﺮﯿﻏ ﺔﻘﯾﺮﻄﺑ ﻚﯿﻠﻌﻓ

ﺔﯾرﺎﻄﺒﻟا لاﺪﺒﺘﺳا

ﻂﻘﻓ عﻮﻨﻟا ﺲﻔﻨﺑ ﺎﮭﻟدﺎﻌﯾ ﺎﻣ وأ ﺎﻤﻛﺖﺻوأ ﺔﻌﻨﺼﻤﻟا ﺔﻛﺮﺸﻟا ﮫﺑ

تﺎﯾرﺎﻄﺒﻟا ﻦﻣ ﺺﻠﺨﺗ ﻟ ﺎﻘﻓو ﺔﻠﻤﻌﺘﺴﻤﻟاﺔﻌﻧﺎﺼﻟا ﺔﻛﺮﺸﻟا تﺎﻤﯿﻠﻌﺘ

MBI-6219G-T8HX/MBI-6119G-T8HX MicroBlade Module User’s Manual

2-10

배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다 . 기존 배터리와 동일하거
나 제조사에서 권장하는 동등한 종류의 배터리로만 교체해야 합니다 . 제조사의 안내에
따라 사용된 배터리를 처리하여 주십시오 .

Waarschuwing

Er is ontploffingsgevaar indien de batterij verkeerd vervangen wordt. Vervang de batterij
slechts met hetzelfde of een equivalent type die door de fabrikant aanbevolen wordt.
Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften afgevoerd te worden.

Redundant Power Supplies

Warning!

This unit might have more than one power supply connection. All connections

must be removed to de-energize the unit.

冗長電源装置

このユニットは複数の電源装置が接続されている場合があります。

ユニットの電源を切るためには、すべての接続を取り外さなければなりません。

警告
此部件连接的电源可能不止一个，必须将所有电源断开才能停止给该部件供电。
警告

此裝置連接的電源可能不只一個，必須切斷所有電源才能停止對該裝置的供電。

Warnung

Dieses Gerät kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass der
Einheit kein trom zugeführt wird, müssen alle Verbindungen entfernt werden.

¡Advertencia!

Puede que esta unidad tenga más de una conexión para fuentes de alimentación. Para
cortar por completo el suministro de energía, deben desconectarse todas las
conexiones.

Attention

Cette unité peut avoir plus d'une connexion d'alimentation. Pour supprimer toute tension
et tout courant électrique de l'unité, toutes les connexions d'alimentation doivent être
débranchées.

דדחא קפסמ רתוי םייק םא

!הרהזא

.קפס לש דחא רוביחמ רתוי שי הדחיל תא ריסהל שי ןקורל תנמ לע םירוביחה לכ

חיה תאי.הד

2-11

Chapter 2: Standardized Warning Statements

경고 !

이 장치에는 한 개 이상의 전원 공급 단자가 연결되어 있을 수 있습니다 . 이 장치에 전
원을 차단하기 위해서는 모든 연결 단자를 제거해야만 합니다 .

Waarschuwing

Deze eenheid kan meer dan één stroomtoevoeraansluiting bevatten. Alle aansluitingen
dienen verwijderd te worden om het apparaat stroomloos te maken

Backplane Voltage

Warning!

Hazardous voltage or energy is present on the backplane when the system is

operating. Use caution when servicing.

バックプレーンの電圧

システムの稼働中は危険な電圧または電力が、バックプレーン上にかかっています。

修理する際には注意ください。

警告
当系统正在进行时，背板上有很危险的电压或能量，进行维修时务必小心。
警告

當系統正在進行時，背板上有危險的電壓或能量，進行維修時務必小心。

Warnung

Wenn das System in Betrieb ist, treten auf der Rückwandplatine gefährliche
Spannungen oder Energien auf. Vorsicht bei der Wartung.

¡Advertencia!

Cuando el sistema está en funcionamiento, el voltaje del plano trasero es peligroso.
Tenga cuidado cuando lo revise.

Attention

Lorsque le système est en fonctionnement, des tensions électriques circulent sur le fond
de panier. Prendre des précautions lors de la maintenance.

. ﺪﻗ اﺬﮭﻟ نﻮﻜﯾ ﻟازﺎﮭﺠ تﻻﺎﺼﺗا ةﺪﻋ تاﺪﺣﻮﺑ ﺔﻗﺎﻄﻟا داﺪﻣا

ﺔﻟازإ ﺐﺠﯾ تﻻﺎﺼﺗﻻا ﺔﻓﺎﻛ لﺰﻌﻟ ﻟاةﺪﺣﻮ ﻦﻋ ءﺎﺑﺮﮭﻜﻟا

יירוחאה לנפב חתמ

זא!הרה

ךלהמב רהזיהל שי .תכרעמה לועפת ןמזב ירוחאה לנפב חתמ תנכס תמייק

.הדובעה