Supermicro C7Z270-PG Quick Reference Manual
C7Z270-PG
ENGLISH
繁體中文
简体中文
日本語
(
한국어
QUICK REFERENCE GUIDE
Revision 1.0
C7Z270-PG QUICK REFERENCE GUIDE Product Safety Information
Standardized Warning Statements
Motherboards
About Standardized Warning Statements
The following statements are industry standard warnings, provided to warn the user of situations which can potentially
cause a bodily injury. Should you have questions or experience difculty, contact Supermicro's Technical Support De-
partment for assistance. Only certied technicians should attempt to install or congure components.
Read this section in its entirety before installing or conguring components in the Supermicro chassis.
Battery Handling
Warning!
There is a danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or an equiva-
lent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
電池の取り扱い
電池交換が正しく行われなかった場合、破裂の危険性があります。 交換する電池はメーカーが推奨する型、または同等のも
のを使用下さい。 使用済電池は製造元の指示に従って処分して下さい。
警告
電池更換不當會有爆炸危險。請使用製造商建議之相同或功能相當的電池更換原有電池。請按照製造商的說明指示處理
廢棄舊電池。
警告
电池更换不当会有爆炸危险。请只使用同类电池或制造商推荐的功能相当的电池更换原有电池。请按制造商的说明处理
废旧电池。
경고!
배터리가 올바르게 교체되지 않으면 폭발의 위험이 있습니다. 기존 배터리와 동일하거나 제조사에서 권장하는 동등한
종류의 배터리로만 교체해야 합니다. 제조사의 안내에 따라 사용된 배터리를 처리하여 주십시오.
Note: For complete product safety information, refer to http://www.supermicro.com/about/policies/safety_information.cfm.
C7Z270-PG QUICK REFERENCE GUIDE BIOS POST Code
AMI BIOS POST Codes
About AMI BIOS POST Codes
The table below lists some of AMI BIOS POST codes for C7Z270-PG. For more information, refer to https://www.
supermicro.com.tw/manuals/other/AMI_BIOS_POST_Codes_for_Grantley_Motherboards.pdf.
Code Description
0x32 CPU post-memory initialization is started
0x55 No Memory detected or memory failed
0x63 CPU DXE initialization is started
0x69 North Bridge DXE initialization is started
0x70 South Bridge DXE initialization is started
0x92 PCI Bus initialization is started
0x99 Super IO Initialization
0x9A USB initialization is started
0xA0 IDE initialization is started
0xA9 Boot into BIOS setup menu
0xAE Legacy Boot event
0xB2 Legacy Option ROM Initialization
0xB4 USB hot plug
0xD6 No VGA device
0xD7 No Keyboard plug in
0xF2 Recovery process started
0xF9 Recovery capsule is not found
C7Z270-PG
Quick RefeRence Guide Rev. 1.0
S
UPERMICR
R
+
+
A
C
A
C
A
DESIGNED IN USA
C7Z270-PG
REV:1.01
BIOS LICENSE
MAC CODE
BAR CODE
JPCIE7
JPCIE1
JPCIE3
JPCIE5
S4
MH15
MH14
MH13
MH12
MH11
MH10
S12
JTBT
PCIE4
JUSBA
JAUDIO1
JUSBC
JUSBLAN2
JUSBLAN1
B1
JBT1
JSTBY1
SP1
JD1
JF1
JSD1
JCOM1
FAN5
FAN1
FAN4
FAN2
FAN3
S8
JTPM1
JPW1
LED3 LED2
LED1
JPW2
JSPDIF_OUT
JI2C2
JI2C1
JL1
LED4
JPAC1
JPL2
JBR1
JLED1
JWD1
JPME2
2
2-3:DISABLE
1-2:ENABLE
JPL2:LAN2
CPU
LAN2 LAN1
ON
PWR
RST
XOH/FF
NIC
NIC
1LED
HDD
LED
PWR
JF1
OFF:DISABLE
ON :ENABLE
JI2C1/JI2C2
AUDIO FP
3 PIN POWER LED
JLED1:
ON:BIOS RECOVERY
COM1
JTPM1:
TPM/PORT80
5V STBY POWER
JSTBY1:
OFF:NORMAL
JBR1
JL1:
CHASSIS
INTRUSION
USB6/7
USB4/5
USB2/3
USB 14/15 (3.0)
PCIE M.2 CONNECTOR 1
CPU SLOT1 PCI-E 3.0 X8 (IN X16)
1-2:RST
2-3:NMI
WATCH DOG
JWD1:
JSD1:
CPU SLOT3 PCI-E 3.0 X16
SATA DOM PWR
U.2 CONNECTOR 1
U.2 CONNECTOR 2
I-SATA5
I-SATA4
BUZZER:3-4
JD1:
SPEAKER:1-4
PCH SLOT4 PCI-E 3.0 X4
CMOS CLEAR
JBT1
I-SATA3
I-SATA2
2-3:ME MANUFACTURING MODE
1-2:NORMAL
JPME2:
CPU SLOT5 PCI-E 3.0 X8 (IN X 16)
1-2:ENABLE
2-3:DISABLE
JPAC1:AUDIO
I-SATA1
I-SATA0
CPU SLOT7 PCI-E 3.0 X16
SYS_FAN2
PCIE M.2 CONNECTOR 2
SYS_FAN3
HD AUDIO
USB 12/13 (3.1)
USB 10/11(3.1)
2-3:DISABLE
JPL1:LAN1
1-2:ENABLE
USB8/9(3.0)
POWER BUTTON
DIMMB1
DIMMB2
DIMMA1
DIMMA2
HDMI/DP
RESET BUTTON
KB/MOUSE
USB 0/1
SYS_FAN1
CPU_FAN1
CLEAR CMOS
CPU_FAN2
Motherboard Layout and Features
7th/6th Gen
Intel
®
CoreTM i7/i5/i3
Series CPU
= mounting hole
LGA 1151
I/O BACK PANEL
Package contents
• One (1) Supermicro Motherboard
• Four (4) SATA Cables, One (1) I/O Shield
• One (1) Quick Reference, One (1) Driver CD
Connector Description
AUDIO FP Front Panel Audio Header
B1 Onboard Battery
COM1 COM1 Port Header
I-SATA0~5 (Intel
®
Z270) Serial ATA (SATA 3.0) Ports 0~5 (6Gb/sec)
JD1 Speaker/buzzer (Pins 1~4: External Speaker, Pins 3~4: Buzzer)
JF1 Front Panel Control Header
JL1 Chassis Intrusion Header
JLED1 Power LED Indicator Header
JPW1 24-pin ATX Main Power Connector (Required)
JPW2 +12V 8-pin CPU power Connector (Required)
JSD1 SATA DOM (Disk On Module) Power Connector
JSPDIF_OUT Sony/Philips Digital Interface Format (S/PDIF) Out Header
JSTBY1 Standby Power Header
JTBT Intel
®
Thunderbolt™ Header
JTPM1 Trusted Platform Module (TPM) Header
PCI-E M.2 CONNECTOR 1, 2* PCI-E M.2 Connectors 1 and 2, small form factor devices and other portable
devices for High speed NVMe SSDs
SYS FAN 1,2,3 / CPU FAN 1,2 System/CPU Fan Headers
U.2 CONNECTOR 1, 2* U.2 Connector 1 and 2, for 2.5” SSD Drives
USB 2/3, USB 4/5, USB 6/7 Front Panel Accessible USB 2.0 Headers 2/3, 4/5. 6/7
USB 14/15 (3.0) Front Panel Accessible USB 3.0 Header 14/15
Jumpers and Connectors
Jumpers
Jumper Description Default
CLEAR CMOS Clear CMOS Switch Push Button Switch
JBR1 BIOS Recovery Switch Pins 1-2 (Disable)
JBT1 Clear CMOS (on board) Short pads to clear CMOS
JI
2
C1/JI2C2 SMB to PCI Slots Open (Disabled)
JPAC1 Audio Enable Pins 1-2 (Enabled)
JPL2 LAN2 Enable/Disable Pins 1-2 (Enabled)
JPME2 Intel
®
Manufacturing Mode Pins 1-2 (Normal)
JWD1 Watch Dog Function Enable Pins 1-2 (RST)
POWER BUTTON Internal Power Button Push Button Switch
RESET BUTTON Onboard System Reset Button Push Button Switch
Connectors
*PCIE M.2 Connector 1 shares with U.2 Connector 1. (When M.2 device is plugged into PCIE M.2 Connector 1, U.1 connector 1 will be automatically disabled.)
*PCIE M.2 Connector 2 shares with SATA4/5. (When M.2 device is plugged into PCIE M.2 Connector 2, SATA4/5 will be automatically disabled.)
ContaCt InformatIon
• www.supermicro.com (Email: support@supermicro.com)
• Manuals: http://www.supermicro.com/support/manuals
• Drivers & Utilities: ftp://ftp.supermicro.com
• Safety: http://www.supermicro.com/about/policies/safety_information.cfm
The C7Z270-PG supports a 6th and 7th generation Intel® CoreTM i7/i5/i3 processor, up to 64GB of Unbuffered (UDIMM)
non-ECC DDR4 memory, up to 3733 MHz (OC) in four 288-pin memory slots. Populating these DIMM slots with
a pair of memory modules of the same type and same size will result in interleaved memory, which will improve
memory performance.
Note: 1) For memory optimization, use only DIMM modules that have been validated by Supermicro. For the latest memory updates, please
refer to our website at http://www.supermicro.com/products/motherboard.
2) Always connect the power cord last, and always remove it before adding, removing or changing any hardware components.
LED Indicators
LED Description Color/State Status
LED1 Onboard Standby PWR LED Green: Solid on Power On
LED2 M.2 connector 2 SSD ACT LED Green: Solid on M.2 device connected
LED3 M.2 connector 1 SSD ACT LED Green: Solid on M.2 device connected
LED4 Status Code LED Digital Readout See manual
LED indicators
CPU & Memory Support
CPU & Memory Support
Towards the CPU
Memory Population Guidelines
When installing memory modules, the DIMM slots should be populated in the following order: DIMMA2, DIMMB2,
then DIMMA1, DIMMB1.
• Always use DDR4 DIMM modules of the same size, type and speed.
• Mixed DIMM speeds can be installed. However, all DIMMs will run at the speed of the slowest DIMM.
Recommended Population (Balanced)
DIMMB2 DIMMA2 DIMMB1 DIMMA1 Total System Memory
4GB 4GB 8GB
4GB 4GB 4GB 4GB 16GB
8GB 8GB 16GB
8GB 8GB 8GB 8GB 32GB
16GB 16GB 32GB
16GB 16GB 16GB 16GB 64GB
DIMMB2 (Gray Slot)
DIMMA2 (Gray Slot)
DIMMA1 (Black Slot)
DIMMB1 (Black Slot)
DIMM Memory Installation
MNL-1917-QRG-100
© 2016 Supermicro Computer Inc. All rights reserved. Reproduction of this document whether in part or in whole is strictly prohibited without Super-
micro's written consent. All Trademarks are property of their respective entities. All information provided is deemed accurate at the time of printing;
however, it is not guaranteed.
Notes
• Graphics shown in this quick reference guide are for illustration only. Your components may or
may not look exactly the same as drawings shown in this guide.
• Refer to Chapter 2 of the User Manual for detailed information on jumpers, connectors, LED
indicators, memory support and CPU/motherboard installation instructions.
Power Butt
on
OH/Fan Fail
LED
1
NIC1 LED
Reset Button
2
HDD LED
Power LED
Reset
PWR
Vcc
Ground
Ground
X
X
Vcc
Vcc
Vcc
1516
X
X
Front Panel Control (JF1)
CPU Installation
Heatsink Installation
Heatsink
with Fan
Motherboard
Mounting Hole
Back Panel I/O Connectors
A. PS/2 Keyboard/Mouse Port F. Gb LAN Port 1 K. USB 3.1 Port 11 P. S/PDIF Out
B. USB 2.0 Port 0 G. USB 3.0 Port 8 L. USB 3.1 Port 12 Q. Line In
C. USB 2.0 Port 1 H. USB 3.0 Port 9 M. USB 3.1 Port 13 (Type C) R. Line Out
D. Display Port I. Gb LAN Port 2 N. Center/LFE Out S. Mic In
E. HDMI Port J. USB 3.1 Port 10 O. Surround Out
G
H
I
J
K
L
O
P
Q
A
B
C
D
E
F
M
N
C7Z270-PG
Add
thermal paste
R
S
Loading...