Superlift S66 Owner's Manual
Address: NO.1298, XJ Avenue, Xuchang, Henan, P.R.China. Tel: 0086 374 277 2299 Fax: 0086 374 277 3675
GARAGE DOOR OPENER
OWNER’S MANUAL
( S66 )
XUCHANG SUPERLIFT M & E EQUIPMENT Co.,Ltd
Contents
1. Required tool list ________________________________________________________01
2. Important safety instructions ______________________________________________ 01
3. Opener installation _______________________________________________________02
3.1 Important installation instruction __________________________________________02
3.2 Installation sketch map __________________________________________________03
3.3 Assembling opener _____________________________________________________03
3.4 Hoisting opener ______________________________________________ 04
4. Adjustment instruction ____________________________________________________05
4.1 Switch on power
_______________________________________________05
4.2 Manipulation instruction
_______________________________ 05
4.3 Function setting ______________________________________06
4.4 Fault information ______________________________________________________07
5. Locking door by hand _____________________________________________________08
6. Installation instruction for the accessory ______________________________________08
6.1 Photo beam installation _________________________________________________08
6.2 Push button installation _________________________________________________09
7. Maintenance and repair ___________________________________________________ 09
8. Technical data ___________________________________________________________09
9. Trouble shooting _________________________________________________________10
- 1 -
IMPORTANT SAFETY INSTRUCTIONS
WARNING – IT IS VITAL FOR THE SAFETY OF PERSONS TO
FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
1. Required tool list
No. Name Specification Quantity Remark
1 Electric drill 1
2 Herringbone ladder (V-ladder) 1
3 Mobile wrench or socket wrench 1 set
4 Band tape 5m 1
5 Screw driver 2
6 Cross-header screw driver 2
7 Pincer 2
2. Important safety instructions
WARNING – INCORRECT INSTALLATION CAN LEAD TO SEVER INJURY FOLLOW
ALL INSTALLATION INSTRUCTIONS IN THIS MANUAL AND ALWAYS DO THE
FOLLOWING:
1) Keep garage doors properly balanced. Have a professional service person make repairs to cables,
spring assemblies and other hardware.
2) Watch a moving door until it completely stops moving. Do not cross the path of a door in
motion, and never let children play “beat the door”. Do not let children play near a garage door
when it is opening or closing.
3) Never put fingers between the sections of a garage door, and teach children to keep their hands
and fingers clear of section joints, hinges, tracks, springs and other door parts.
4) Do not let children play with transmitters or remote controls, and place these items out of reach
of children.
5) Test the automatic reversal monthly. The garage door MUST reverse on contact with a 40mm
high object (or a 50mm by 100mm board laid flat) on the floor. If the garage door does not
reverse, adjust either the force or the limit of travel, and re-test the automatic reversal. Be
careful when making adjustments because maladjustments can cause serious injury or death.
6) Disconnect the electrical power to the operator before making any repairs or removing the
housing cover.
7) If possible, use the emergency release only when the door is closed. Be careful when using the
release with the door open because weak or broken springs may allow the door to fall rapidly,
which can cause serious injury or death.
8) Do not use the emergency release rope to open or close the door!
9) All the Entrapment Warning Label should be pasted in a prominent location.
10) Check the function of the operator on a monthly basis!
11) Please take good care of this manual after installation so as to have safety inspection and
maintenance regularly according to the manual.
- 2 -
3. Installation instructions
3.1. Important installation instructions
In order to reduce the risk of serious injuries or death, please read and follow all instructions
provided!
1) Install only on a properly balanced door. An improperly balanced door has the potential to
inflict severe injury. Have a qualified service person make repairs to cables, spring assemblies,
and other hardware before installing the opener!
2) Remove all ropes and remove or make inoperative all locks connected to the garage door before
installing opener!
3) Where possible, install the operator 2.1 meters or more above the floor. For products having an
emergency release, mount the emergency release approx. 1.8 meters above the floor!
4) Do not connect the opener to source of power until instructed to do so!
5) Locate the control button:
• Within sight of door
• At a minimum height of 1.5 meters so small children are not able to reach it, and
• Away from all moving parts of the door
6) Install the entrapment warning label next to the control button in a prominent location. Use
staple gun to secure label to surfaces to which the adhesive will not adhere. Install the
Emergency Release Marking. Attach the marking on or next to the emergency release!
7) This operator is to be used only with residential sectional or one-piece doors!
8) To avoid damage to the garage door and operator, disable locks before installing and operating
the operator.
9) Prior to installation check for and avoid any damaging of covered electrical, gas or water lines
in the walls or ceilings!
10) The garage ceiling must be designed so that a secure fastening of the operator is guaranteed!
11) The installer must ensure that the operator is firmly attached to the garage structure! Do not
attach to gypsum or plaster ceilings!
12) The enclosed emergency release rope must be installed at an easy to reach height! Check the
emergency release to ensure operation with only moderate force required!
13) Do not use the emergency release rope to open or close the door!
14) Check the function of all safety devices (light beam device, emergency release, and automatic
reversal)!
15) After installing the opener, the door must reverse when it contacts a 40mm high object (or a
50mm by 100mm board laid flat) on the floor!
16) The mechanical limitation device should be installed on the horizontal rail terminal of garage
door’s two, in order to avoid the panel slide out of the rail.
17) The installation and wiring must be complied with the architectural working standard and
electrical rules.
Work safely!
Always wear appropriate safety protection when using any tools!
For garages without a second access an additional emergency release is necessary, which
prevents a possible lock out!
Loading...