Superior Fireplaces WRT3538WS, WRT3543WS, WRT3538WH, WRT4038IH, WRT4043IS Installation And Operation Instruction Manual

PFS

USC

P/N 900855-00 Rev. B 02/2018

P900855-00

Installation and Operation Instructions

Indoor Wood-burning Fireplace

Ce manuel est disponible en francais, simplement
en faire la demande. Numéro de la pièce 900855-01.

®

REPORT NO. F17-136

WRT3538WS
WRT3538WH
WRT3543WS
WRT3543WH

Models

WRT4038IS
WRT4038IH
WRT4043IS
WRT4043IH

SAVE THIS BOOK

This book is valuable. In addition to instructing you on how to install and maintain your appliance, it also
contains information that will enable you to obtain replacement parts or accessory items when needed. Keep
it with your other important papers.

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future
reference.

Installateur : Laissez cette notice avec l’appareil.
Consommateur : Conservez cette notice pour consultation
ultérieure.

This wood-burning fireplace complies with UL127
CAN/ULC-S610-M87 standard as a FACTORY
BUILT FIREPLACE.

This fireplace is approved for use as a wood-burning fireplace or for use with a vented gas log approved to
ANSI Z21.60 or Z21.84 standards or for use with a vent-free gas log heater approved to ANSI Z21.11.2 standard

FOR CANADA: The authority having jurisdiction (such
as the municipal building department, fire department,
etc.) should be contacted before installation to
determine the need to obtain a permit.

Ce foyer au bois est conforme aux UL 127 CAN/ULC­S610-M87 norme comme une USINE CONSTRUITE
CHEMINÉE.

.

POUR LE CANADA: L’autorité compétente (comme
le service municipal du bâtiment, les pompiers,
etc.) doit être contacté avant l’installation afin de
déterminer la nécessité d’obtenir un permis.

This installation manual will enable you to obtain a safe, efficient and dependable installation of your fireplace
system. Please read and understand these instructions before beginning your installation.

Do not alter or modify the fireplace or its components under any circumstances. Any modification or alteration of
the fireplace system, including but not limited to the fireplace, chimney components and accessories, may void the
warranty, listings and approvals of this system and could result in an unsafe and potentially dangerous installation.

IMPORTANT! TO ASSURE PROPER ALIGNMENT OF GLASS DOORS: INSTALL THIS FIREPLACE IN A SQUARE
AND PLUMB CONDITION, USING SHIMS AS NECESSARY AT SIDES AND/OR BOTTOM.

NOTE: DIAGRAMS AND ILLUSTRATIONS THROUGHOUT THE MANUAL ARE NOT TO SCALE.

Thank you for your purchase. We appreciate your
business!

Please carefully read and follow all instructions in this manual. Pay
special attention to all warnings and safety information.

Following these safety, care, and operation instructions will help
ensure many years of dependable and enjoyable service from your
fireplace.

Please read and understand these instructions before installing
or operating.

SAFETY

TABLE OF CONTENTS

Safety .............................................................................................2

Draft Smoke Guidelines & Troubleshooting....................................4

Specifications .................................................................................6

Fireplace Installation ......................................................................7

Venting Installation ......................................................................10

Refractory Panels Installation ......................................................17

Masonry Brick Panels Installation ................................................18

Optional Gas Line Installation ......................................................19

Glass Door Installation .................................................................20

Operation and Maintenance Guidelines ........................................21

Important Notices - Canada .........................................................23

Technical Service .........................................................................23

Replacement Parts .......................................................................23

Parts ............................................................................................24

Accessories ..................................................................................28

Warranty ......................................................................................31

WARNING: Improper installation, adjustment,
alteration, service or maintenance can cause injury
or property damage. Refer to this manual for correct
installation and operational procedures. For assis­tance or additional information consult a qualified
installer, service agency or the gas supplier.

IMPORTANT: Check local codes before installing this
fireplace.

Before beginning the installation of the fireplace, read these instruc­tions through completely.

• This INNOVATIVE HEARTH PRODUCTS, LLC (IHP) fireplace and
its components are safe when installed according to this installa­tion manual. Unless you use IHP components, which have been
designed and tested for the fireplace system, you may cause a
fire hazard.

• The IHP warranty will be voided by and IHP disclaims any re­sponsibility for the following actions.

a. Modification of the fireplace, components, doors, air inlet

system and damper control.

b. Use of any component part not manufactured or approved by

IHP in combination with an IHP fireplace system.
Proper installation is the most important step in ensuring safe and
continuous operation of the fireplace. Consult the local building codes
as to the particular requirements concerned with the installation of
all factory built fireplaces.

WARNING: Do not install a fireplace insert in this
box unless the manufacturer's instructions with the
insert specifically state this fireplace has been tested
for use with this insert.

FOR YOUR SAFETY

• Do not store or use gasoline or any other flammable
vapors or liquids in the vicinity of this or any other
appliance.

• Due to high temperatures, the appliance should be
located out of traffic and away from furniture and
draperies.

• Do not place clothing or other flammable materials
on or near the appliance.

• Never leave children unattended when a fire is
burning in the fireplace.

WARNING: Use solid wood or processed solid fuel
firelogs only. When processed wood fuel fire logs are
used, do not poke or stir the logs while they are burning.
Use only fire logs that have been evaluated for the ap­plication in fireplace and refer to fire log warnings and
caution markings on packaging prior to use.

This fireplace is not intended to be used as a substitute
for a furnace to heat an entire home. Use for supple­mental heat only.

Overfiring of a fireplace is a condition where exces­sive temperatures are reached, beyond the design
capabilities of the appliance. The damage that occurs
from overfiring is not covered under the manufacturer’s
limited warranty.

SuperiorFireplaces.us.com 900855-00_B2

SAFETY Continued

WARNING: CONTINUED OVERFIRING CAN PER­MANENTLY DAMAGE YOUR FIREPLACE SYSTEM.
SOME EXAMPLES OF CONDITIONS THAT COULD
CAUSE OVERFIRING ARE:

• BURNING QUANTITIES OF SCRAP LUMBER, PINE BRANCH­ES, PAPER OR CARDBOARD BOXES WHICH EXCEED THE
VOLUME OF THE NORMAL LOG FIRE.

• BURNING TRASH, CHEMICALS OR CHEMICALLY TREATED
COMBUSTIBLES.

Disposal of Ashes
Ashes should be placed in a metal container with a tight-

fitting lid. The closed container of ashes should be placed
on a noncombustible floor or on the ground, well away
from all combustible materials, pending final disposal.
If the ashes are disposed of by burial in soil or otherwise
locally dispersed, they should be retained in the closed
container until all cinders have thoroughly cooled.

WHEN USING THE DECORATIVE APPLIANCE, THE
FIREPLACE DAMPER MUST BE SET IN THE FULLY
OPEN POSITION.

Never use gasoline, gasoline-type lantern fuel, kero­sene, charcoal lighter fluid, or similar liquids to start
or ’freshen up’ a fire in this fireplace. Keep all such
liquids well away from the fireplace while it is in use.

WARNING: BURNING IMPROPER FUEL (I.E. CHAR­COAL) CAN RESULT IN CARBON MONOXIDE POISON­ING, WHICH MAY LEAD TO DEATH!

Carbon Monoxide Poisoning – Early signs of carbon
monoxide poisoning resemble the flu with headaches,
dizziness, or nausea. If you have these signs, get
fresh air at once! Have the appliance inspected by a
qualified service technician. Some people are more af­fected by carbon monoxide than others. These include
pregnant women, people with heart or lung disease
or anemia, those under the influence of alcohol, and
those at high altitudes.

Ventilation Requirements - Provide adequate air for
combustion. The fresh air requirements of this ap­pliance must be met within the space where it will
be installed.

Smoke Detectors - Since there are always several
potential sources of fire in any home, we recommend
installing smoke detectors. If possible, install the
smoke detector in a hallway adjacent to the room (to
reduce the possibility of occasional false activation
from the heat produced by the appliance). If your local
code requires a smoke detector be installed within the
same room, you must follow the requirements of your
local code. Check with your local building department
for requirements in your area.

Use SOLID WOOD only for fuel. It is best to use dry
and well seasoned hardwood. Softwoods tend to burn
very quickly. DO NOT use treated wood, charcoal, coal,
trash, driftwood or woods that have been dipped in
tar, pitch, pine tar, creosote, etc. Wood products made
with synthetic binders, such as plywood, produce ab­normally high temperatures and sputtering, smoking
fires. When burning artificial logs, please read and
follow the instructions provided by the manufacturer.

Never burn treated construction lumber or scraps.
These woods burn excessively hot and may contain
chemicals used to treat insects and fungus. When
burned, these chemicals can pose a significant hazard.

IMPORTANT: See page 4 for additional information
regarding draft requirements, smoking causes and
troubleshooting.

Creosote – Formation and Need for Removal

When wood is burned slowly, it produces tar and other
organic vapors, which combine with expelled mois­ture to form creosote. The creosote vapors condense
in the relatively cool chimney flue of a slow-burning
fire. As a result, creosote residue accumulates on
the flue lining. When ignited this creosote makes an
extremely hot fire.

The chimney shall be inspected at least twice a year
during the heating season to determine when a creosote
buildup has occurred. When creosote has accumulated
(1/8" [3 mm] or more) it shall be removed to reduce
the risk of a chimney fire.

WARNING: Children and adults should be alerted
to the hazards of high surface temperatures and to
stay away to avoid burns or clothing ignition. Young
children should be carefully supervised when in the
same room as fireplace.

SuperiorFireplaces.us.com900855-00_B 3

DRAFT SMOKE GUIDELINES AND TROUBLESHOOTING

Draft Requirements

Your wood-burning appliance is dependent upon a properly func­tioning chimney for optimum performance. It is important to match
the wood-burning appliance to the chimney. The chimney has two
functions:

1. It draws combustion air into the appliance (without air, no fuel
will burn) and

2. It exhausts combustion by-products. Your new appliance is what
is known as a “natural draft” appliance.

The appliance depends solely on the natural draft of the chimney
system to draw combustion air into the unit. Draft is the force that
moves air from the appliance up into the chimney. The amount of
draft in your chimney depends on the length of the chimney, local
geography, nearby obstructions and other factors. Too much draft
may cause excessive temperatures in the appliance (overfiring). Slow
or inadequate draft equals poor combustion and possible smoking
problems. The following are some conditions that may contribute
to poor chimney draft:

1. A chimney too large for your appliance.

2. A chimney with not enough height to produce adequate draft.

3. A chimney with excessive height (this may allow exhaust to cool
too much before exiting, which will stall the rate the exhaust exits).

4. Offsets in the venting system are too restrictive (see Chimney
Guidelines).

Inadequate draft will cause the appliance to leak smoke into the room
through the wood-burning appliance and the chimney connector joints.
Excessive draft may cause an uncontrollable burn or a glowing red
appliance or chimney part.
Overfiring Damage - If the appliance or chimney connector glows,
you are overfiring. Other symptoms may include: Cracking, warping
or burning out of components, plated accessories may turn color,
appliance glass may develop a haze, which will not come off with
cleaning.

Overfiring of a appliance is a condition where excessive tempera­tures are reached, beyond the design capabilities of the appliance.
The damage that occurs from overfiring is not covered under the
manufacturer’s limited warranty.

Also see Troubleshooting on Page 5.

WARNING

Neither the manufacturer nor the seller warrants “smoke
free” operation nor are we responsible for inadequate
system draft caused by mechanical systems, general
construction conditions, inadequate chimney heights,
adverse wind conditions and/or unusual environmental
factors or conditions beyond our control.

Selecting the Proper Venting System

The appliance is merely one component of a larger system. The
other equally important component is the venting system. This is
necessary for achieving the required flow of combustion air to the fire
chamber and for safely removing unwanted combustion by products
from the appliance.

If the venting system’s design does not promote these ends, the system
may not function properly. Poorly functioning venting systems may
create performance problems as well as be a safety hazard. A draft

test should read greater than .04’ W.C. (inches water column) and
less than .08” W.C. As per NFPA-211 standard, the installer must

take into account all variables within the installation and install the
appliance in such a manner that satisfies the draft requirements of
the appliance. See Chimney Guidelines to assist you in selecting the
proper venting system for your installation.

American National Standards Institute ANSI/NFPA 211, Standard
for Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appli­ances - See Draft Section: A chimney or vent shall be so designed

and constructed to develop a flow sufficient to completely remove all
flue and vent gases to the outside atmosphere. The venting system
shall satisfy the draft requirements of the connected appliance in
accordance with the manufacturer’s instructions.

Chimney Guidelines:

• Most wood-burning appliances requires approximately 12 feet
minimum of “effective draw” provided by the venting system. As a
rule of thumb, every 90 degree total direction change in the venting
will result in a loss of approximately 5 feet of “effective draw.”
Example: If two 45 degree offsets are used, subtract 5 feet from
the actual vertical vent height to determine your “effective draw.”
In this case if you had 14 feet of vertical vent, the effective draw
would only be approximately 9 feet (14 ft. - 5 ft. = 9 ft.), therefore
it may be necessary to add additional height to the venting system.

• Do not install an offset within the first two feet above the flue outlet
on the appliance.

• In well insulated and weather tight homes, it may be difficult to
establish a good draft up your chimney. The poor draft is caused
by a shortage of air in the house. In this situation an Outside Air
Kit may need to be installed (See Negative Pressure Warning be­low and Outside Combustion Air in the Installation and Operation
manual).

Negative Pressure Warning

These appliances are not designed to be operated in a negative
pressure. In very airtight homes with large kitchen exhaust fans,
furnace cold air returns, fresh air exchange systems and any other
air system in close proximity to the heating appliance may create a
negative pressure in the same room as the heating appliance. This can
create dangerous back drafting of the appliance and chimney joints,
drawing combustion by-products into the home. Be sure your home
has adequate makeup air to eliminate negative pressures caused by
the above-mentioned sources. Outside air connected to the appliance
probably will not resolve such a problem as the appliance is not the
source of negative pressure. IHP accepts no liability for damages
resulting from negative pressures described here.

Ventilation Requirements - Provide adequate air for combustion.
The fresh air requirements of this appliance must be met within the
space where it will be installed. Ventilation is essential when using
a solid-fuel-burning appliance. In well insulated and weather tight
homes, it may be difficult to establish a good draft up the chimney
(caused by a shortage of air in the home). The lack of air is caused
by many common household appliances which exhaust air from the
home (such as a furnace, heat pump, air conditioner, clothes dryer,
exhaust fans, fireplaces, and other fuel burning appliances). Also, the
combustion process of this appliance uses oxygen from inside the
dwelling. If the available fresh air delivery in the dwelling is insufficient
to support the demands of these appliances, problems can result
(i.e. excessive negative pressure can develop in the dwelling which
will affect the rate at which this appliance can draft thus resulting
in performance problems or smoking. To correct this problem it
may help to open a window (preferably on the windward side of the
house) or install an outside air kit.

SuperiorFireplaces.us.com 900855-00_B4

DRAFT SMOKE GUIDELINES AND TROUBLESHOOTING Continued

Smoking – Causes And Troubleshooting

To reduce the likelihood of smoking when opening the door, open
the combustion air control or damper before opening the door.
Your appliance has been designed and tested to provide smoke free
operation. Occasionally, there may be a small amount of smoking
upon lighting the fire, until the chimney heats up but this should not
continue. If the appliance continues to smoke it is probably for one
of the following reasons:

A. Negative pressure in the house -

As the fire burns, air goes up the chimney. This air must be

replaced through leakage into the house or through the outside
air duct. When operating the appliance, open a nearby window
temporarily to check if there is adequate replacement air supply.

B. Blowers operating (e.g.: range hood) - These blowers draw air

out of the house and may actually cause a negative pressure in
the house. Turn off all blowers and open a nearby window to
determine if this is the cause of the problem.

C. Wet wood - Wet or tarred wood will smoulder and smoke instead

of burning properly.

Your dealer can help you determine if you

have properly seasoned wood for burning.

D. Dirty or blocked chimney - Check to make sure the chimney is

clear and clean.

If dirty call a certified chimney sweep or use a

properly sized chimney brush to clean.

E. Chimney not long enough - Refer to page 7 for minimum and

maximum chimney height Requirements. The chimney must
extend at least three (3) feet (915 mm) above its point of contact
with the roof and at least two (2) feet (610 mm) higher than any
roof or wall within ten (10) feet (3 m) of it. Additional height will
increase draft and will decrease the tendency to smoke.

F. Poor chimney draft - With no fire, there should be sufficient draft

to exhaust cigarette smoke introduced under the baffle or flue baffle.
Chimneys installed against an outside wall without protection may
generate back draft problems which will cause start-up problems.
To prevent this, open a nearby window, roll up a piece of paper and
light it. Then, hold it in the upper part of the firebox to warm up
the chimney. Wait until the draft is sufficient, then start the fire.

Locating The Appliance

The best location to install your appliance is determined by considering
the location of windows, doors, and the traffic flow in the room where
the appliance is located, allowing space in front of the unit for the
hearth extension and the mantel, and taking into consideration the
location of the hot air ducts (some models), outside air kit and chimney.
If possible, you should choose a location where the chimney will pass
through the house without cutting floor or roof joists.

When selecting the location, the chimney outlet position and the
direction of the wind are important factor affecting the chimney per­formance. To allow a maximum draft and to reduce wind turbulence,
the chimney must:

• Penetrate the highest part of the roof.

• Be installed as far as possible of roof offsets, trees or any other
obstructions that may cause wind turbulence and back drafts in
the chimney.

• The least amount of offsets (elbows) possible. NOTE: A maximum
of 2 offsets is allowed.

Location Recommended

Marginal Location

Wind Direction

Tree

Location

Recommended

Outside Air
Intake
Facing the Wind

Figure 1

Not

Location
Not
Recommended

Prohibited Fuels

These appliances are designed to burn natural well-seasoned wood.
The wood fuel should be air dried seasoned hardwoods, as compared
to softwoods or to green or freshly cut hardwoods. Burning artificial
logs, in some model appliances is allowed (see Installation and Op­eration manual); please read and follow the instructions provided by
the manufacturer. DO NOT BURN:

• Garbage;

• Lawn clippings or yard waste;

• Materials containing rubber,
including tires;

• Materials containing plastic;

• Waste petroleum products,
paints or paint thinners, or
asphalt products;

• Materials containing asbestos;

• Construction or demolition
debris;

• Railroad ties or pres­sure-treated wood; woods that
have been dipped in tar, pitch,
pine tar, creosote, etc.

• Manure or animal remains;

• Salt water driftwood or
other previously salt water
saturated materials;

• Unseasoned wood;

• Christmas tree branches;

• Paper products, colored
paper, cardboard, plywood,
or particleboard;

• Gasoline;

• Naphtha;

• Engine Oil;

• Flammable Liquids;

• Solvents;

• Grease; or

• Charcoal or Coal

NOTE: The use of a firewood moisture meter is recommended
to ensure the firewood contains less than 20% moisture.

Seasoning Guide

Softwoods - 6 months to 18 months
Hardwoods - 12 months to 24 months

Logs that are 5” diameter across or larger should be split in half,
three pieces if over 8 inches, and four pieces when over a foot
across. If a tree has been dead for 2 - 4 years it still needs to be
cut, split, and seasoned for 6 to 24 months depending on the wood.

Standard

8 Ft.

8'

(2.4M)

Cord of
Wood

4 Ft.

4'

(1.2M)

4 Ft. (1.2M)

Figure 2

4'

SuperiorFireplaces.us.com900855-00_B 5

SPECIFICATIONS

MODEL CATALOG NO.

WRT3538WS F3412
WRT3538WH F3413
WRT4038IS F3414
WRT4038IH F3415
WRT3543WS F3416
WRT3543WH F3417
WRT4043IS F3418
WRT4043IH F3419

11-1/2"

(292 mm)

44-1/8"

(1121 mm)

24-5/8"

(626 mm)

8"

(204 mm)

1" (26 mm) CHIMNEY
AIRSPACE CLEARANCE TO
COMBUSTIBLE MATERIAL

38 = 50" (1270 mm)

43 = 54-3/4" (1391 mm)

38 = 38" (966 mm)

43 = 42-3/4" (1086 mm)

38 = 48" (1219 mm)

43 = 52-3/4" (1416 mm)

1" (26 mm)

AIR SPACE

BACK AND SIDES

OUTSIDE AIR

GAS LINE

KNOCKOUT

0" (0 mm)

TO BOTTOM

(1289 mm)

49-7/8"

(1267 mm)

50-3/4"

25-3/4"

(654 mm)

5" (127 mm)

12" (305 mm)

EACH SIDE

14-1/8"

(359 mm)

NO COMBUSTIBLE
MATERIAL ON FACE

COMBUSTIBLE
WALL BOARD

MINIMUM 12" (305 mm)

TO PERPENDICULAR

SIDEWALL

HEARTH EXTENSION
62" X 20" (1575 mm x 508 mm) 38" MODEL
67" X 20" (1702 mm x 508 mm) 43" MODEL

38 = 26-3/8" (670 mm)
43 = 31-1/8" (791 mm)

15" (381 mm)

12-3/8"

(315 mm)

38 = 24" (610 mm)

43 = 26-3/8" (670 mm)

TOP VIEW

5/8" (16 mm)

FRONT

11-5/8" (296 mm)

LEFT SIDE RIGHT SIDE

13-1/8"

(334 mm)

15-1/8"

(385 mm)

9-1/4"

(235 mm)

Figure 3 - Fireplace Specifications

SuperiorFireplaces.us.com 900855-00_B6

FIREPLACE INSTALLATION

SELECTING LOCATION

To determine the safest and most efficient location for the fireplace,
you must take into consideration the following guidelines:

1. The location must allow for proper clearances (see Figures 4 thru

7).

2. Consider a location where fireplace will not be affected by drafts,
air conditioning ducts, windows or doors.

3. A location that avoids cutting of joists or roof rafters will make
installation easier.

4. An outside air kit is available with this fireplace (see Optional
Outside Air Kit on page 10).

MINIMUM CLEARANCE TO COMBUSTIBLES

Back and sides of fireplace 1" (26 mm) min.
Ceiling 42" (1067 mm) min.
Front of fireplace 48" (1220 mm) min.
Floor** 0" (0 mm) min.
Perpendicular wall to opening 12" (305 mm) min.

Top spacers 0" (0 mm) min.
Mantel clearances
Chimney outer pipe surface 1" (26 mm) min.

* Not required at nailing flanges
** See step 2 of Framing

see Mantels, page 9

WARNING: Do not pack required air spaces with

insulation or other materials.

Minimum/Maximum Chimney Height for Residential Installation

Minimum height of chimney, measured from base of fireplace to flue
gas outlet of termination, is 16 feet for straight flue or a flue with one
elbow set. Maximum distance between elbows is 6 feet. For systems
with two elbow sets, minimum height is 22 feet. Maximum height of
any system is 50 feet. This measurement includes fireplace, chimney
sections and height of termination assembly at level of the flue gas
outlet (see Figure 17, page 13).

FRAMING

1. Frame opening for fireplace using dimensions shown in Figures 4
and 5.

2. If fireplace is to be installed directly on carpeting, tile or any
combustible material other than wood flooring, fireplace must
be installed upon a metal or wood panel extending full width and
depth of fireplace.

3. Set fireplace directly in front of this opening and slide unit back
until nailing flanges touch side framing.

4. Check level of the fireplace and shim with sheet metal if necessary.

5. Before securing fireplace to prepared framing, ember protector
(provided) must be placed between hearth extension (not sup­plied) and under bottom front edge of fireplace to protect against
glowing embers falling through. If fireplace is to be installed on a
raised platform, a Z-type ember protector (not supplied) must be
fabricated to fit your required platform height. Ember protector
should extend under fireplace a minimum of 1 1/2". Ember protector
should be made of galvanized sheet metal (28 gauge minimum to
prevent corrosion.

6. Using screws or nails, secure fireplace to framing through flanges
located on sides of fireplace.

SuperiorFireplaces.us.com900855-00_B 7

FIREPLACE INSTALLATION Continued

Back Wall of Chase/Enclosure

FRAMING SPECIFICATIONS

A

B

C

D

E

F

G

J

(1251 mm)

(1293 mm)

(667 mm)

(334 mm)

(1962 mm)

(981 mm)

(667 mm)

(279 mm)

Fireplace Opening Width

38 43

49-1/4"

(1372 mm)

50-7/8"

50-7/8"

(1293 mm)

26-1/4"

(787 mm)

13-1/8"

15-1/2"

(394 mm)

77-1/4"

(2083 mm)

38-5/8"

(1041 mm)

26-1/4"

26-1/4"

(667 mm)

11"

(279 mm)

54"

31"

82

41"

11"

AK4
Combustion
Air Kit

"

AK4 Combustion
Air Kit

K

Back Wall of Chase/Enclosure
Including Finising Materials if any

A

Inside Chase

Rough Framing Face
(Unfinished Shown)

Figure 5 - Inside Chase

Including Finishing Materials
if any

D

G

F

K

Note: All framing dimensions calculated for 1/2" dry wall at the fireplace
face. If sheathing the chase or finishing with other thickness materials,
calculations will need to be made.

54-5/8"

(1388 mm)

58"

(1473 mm)

Header

B

Figure 6 - Corner Installation

AK-4 Combustion
Air Kit

J

Rough Framing Face
(Unfinished Shown)

C

A
E

Corner Installation

Back Wall of Chase/Enclosure

Including Finishing Materials

A

Rough

Framing Face

(Unfinished Shown)

if any

G

Outside Chase

A

Figure 4 - Fireplace Framing

Figure 7 - Outside Chase

SuperiorFireplaces.us.com 900855-00_B8

FIREPLACE INSTALLATION Continued

Combustible
Mantel

HEARTH EXTENSION

A hearth extension projecting a minimum of 20" in front of and a
minimum of 12" beyond each side of fireplace opening is required
to protect combustible floor construction in front of fireplace. Fabri­cate a hearth extension using a material which meets the following
specifications: a layer of noncombustible, inorganic material having a
thermal conductivity of k=0.84 BTU IN/FT, HR. F (or less) at 1" thick.
For example, if the material selected has a k factor of 0.25, such as
glass fiber, the following formula would apply:

0.25 x 1.0" = 0.30" thickness required

0.84
Thermal conductivity "k" of materials can be obtained from manufac-

turer or supplier of noncombustible material. If hearth extension is
to be covered, use noncombustible material such as tile, slate, brick,
concrete, metal, glass, marble, stone, etc. Provide a means to prevent
hearth extension from shifting and seal gap between fireplace frame
and hearth extension with a noncombustible material (see Figure 8).

WARNING: Hearth extension is to be installed only

as shown in Figure 8.

Seal Gap

Fireplace Front

Ember Protector

MANTELS

A mantel may be installed if desired (see Figure 9). Woodwork such
as wood trims, mantels or any other combustible material projecting
from front face must not be placed within 12" of the fireplace (NFPA
211, Section - Clearance from Combustible Material).

Mantels or any other combustible material also may come up to side
edge of black metal face of fireplace as long as projections from front
face fall within limit shown in Figure 9.

Finished Wall

Header

12"

(305 mm)

Max.

Spacer

12"

*

(305 mm)

Min.

Noncombustible
Wall Covering

Fireplace Opening

* A 1-1/2" Projection Is Permitted
Between The Face Top And Mantle

Fireplace Front Raised
Hearth

Ember Protector

Fireplace Front Elevated

Ember Protector

Figure 8 - Hearth Extension

Seal Gap

Hearth

Extension

Combustible Materials
Allowed in Shaded Area

4-17/32"

(115 mm)

30˚

12" (305 mm)

Minimum Distance

to Protected Side Wall

Figure 9 - Mantel Clearances to Combustible Materials

1/2"

(13 mm)

SuperiorFireplaces.us.com900855-00_B 9

VENTING INSTALLATION

OPTIONAL OUTSIDE AIR KIT (MODEL AK4/AK4F)

The installation of an outside air kit should be performed during
the rough framing of the fireplace due to the nature of it's location.
Outside combustion air is accessed through a vented crawl space
(AK4F) or through a sidewall (AK4).See page 21 for instructions of
operating air kit.

CAUTION: Combustion air inlet ducts shall not

terminate in attic space.

The maximum height for the air vent can not exceed
3 feet below the flue gas outlet of the termination.

Secure to Collars with Metal Tape, Screws
or Straps (Min. of 1/4" x 20" in size)

Vent Hood
Required
for Wall
Installation

Vented
Crawl Space
(Check Local
Codes Before
Installing in a
Vented Crawl
Space)

Air Inlet
Location
Must Allow
For Bushes
or Snow

Air Inlet
Eyebrow

Figure 10 - Outside Air Kit

LINEAL GAIN

PART NO. DESCRIPTION GAIN

Fireplace 49 3/4" (1264 mm)

12-12DM

12-12HT

18-12DM

18-12HT

24-12DM

24-12HT

36-12DM

36-12HT

48-12DM

48-12HT
RLT-12D

RLT-12HT

STL-12D

* The lineal gain for the terminations is measured to the flue gas outlet
height.

15" Galvanized
Outer Pipe

12 3/8"
Stainless
Inner Pipe

Pipe Section 10 5/8" (270 mm)

Pipe Section 16 5/8" (423 mm)

Pipe Section 23 5/8" (600 mm)

Pipe Section 34 5/8" (880 mm)

Pipe Section 46 5/8" (1185 mm)

Round Termina-

tion

Square Chase-

Top with Slip

Section

* (197 mm)

7 3/4"

7

" (178 mm)

15"* (381 mm)

Hemmed
End

to

CHIMNEY PIPE

WARNING: Label part number 900599-01 must
be applied by the installer to all chimney pipe
sections but is not required on sections that will
be visible after the installation is complete. Label
must wrap around the circumference of the pipe.
See accessories, page 29 for Kit F2659.

The IHP chimney system consists of 12", 18", 24", 36" and 48" snap­lock, double-wall pipe segments, planned for maximum adaptability
to individual site requirements. Actual lengths gained after fitting
overlaps must be taken into consideration (lineal gain) and are given
in the lineal gain chart (see Figure 11). Lineal Gain is the actual mea­surable length of a part after two or more parts are connected. For
Canada, use chimney parts designated "HT".

WARNING: The opening in the collar around the
chimney at the top of the fireplace must not be ob­structed. Never use blown insulation to fill the chimney
enclosure.

Figure 11 - Lineal Gain

ASSEMBLY AND INSTALLATION OF DOUBLE WALL CHIMNEY
SYSTEM

Each double wall chimney section consists of a galvanized outer pipe, a
stainless steel inner flue pipe and a wire spacer. The pipe sections must
be assembled independently as the chimney is installed. When connect­ing chimney directly to the fireplace, the inner flue pipe section must be
installed first with the lanced side up. The outer pipe section can then
be installed over the flue pipe section with the hemmed end up. Press
down on each pipe section until the lances securely engage the hem on
the fireplace starter. The wire will assure the proper spacing between the
inner and outer pipe sections.

Continue to assemble chimney sections as outlined above, making
sure that both the inner and outer pipe sections are locked together.
When installing double wall snap-lock chimney together, it is impor­tant to assure the joint between the chimney sections is locked. Check
by pulling chimney upward after locking. The chimney will not come
apart if properly locked. It is not necessary to add screws to keep the
chimney together (exception, see Figure 12, page 11).

The height of a vertical chimney pipe supported ONLY by the fire-
place, must not exceed 20 feet. Chimney heights above 20 feet must
be supported.

SuperiorFireplaces.us.com 900855-00_B10

VENTING INSTALLATION Continued

OFFSET

A B 12" 18" 24" 36" 48"

4 3/8" 16 3/8"
9 3/4" 25 1/2"

12 3/4" 30 3/4"

15" 34 3/4"

18" 40"
21 1/4" 46 1/4"
23 3/4" 49 1/4"
27 3/4" 56 3/4"

30" 60 3/4"

33" 66"

36" 71"
38 1/4" 75"
41 1/4" 80 1/4"

45" 86 3/4"
46 3/4" 89 1/2"

51" 97"
53 1/4" 101"
56 1/4" 106 1/4"
59 1/4" 111 1/2"
61 3/4" 115 1/2"
64 3/4" 120 3/4"
68 1/4" 127"

70" 130"
74 1/4" 137 1/2"

RISE CHIMNEY LENGTH

ELBOW SET ONLY

1

1

1

1 1

1 1

1 1

1 1

1 1

1 1 1

1 2

1 1 1

1 2

1 2

1 1 2
1 2 1

1 2 1

1

2

1 1

2 1

4

USING ELBOW OFFSETS (30E-12DM)

1.

To achieve desired offset, you may install combinations of 12",
18", 24", 36" and 48" length of double wall pipe (see offset chart
and Figure 12).

2.

Chimney weight above offset rests on return elbow. Straps must
be securely nailed to rafters or joists (see Figure 13, details A and
B).

3. Maximum length of pipe between supports (return elbow or

1

2

12S-12DM) is 6' of angle run. Maximum of two 6' angle run
sections per chimney system (see Figure 14, page 12).

4. All pipe connections between the offset and return must be
secured with two screws on the outer pipe only (see Figure

12). Do not penetrate the inner stainless.

See Detail A

2" (51 mm)

Min.

Straps

Straps

Detail B

Angle Firestop

See Detail B

OFFSET CHART (22-50 FT. SYSTEM HEIGHT)

Screws

Straps

Detail A

Return Elbow

Figure 13 - Ceiling Support Pipe 12S-12DM

Straps

CAUTION: THE STRUCTURAL INTEGRITY OF THE

B

MANUFACTURED HOME FLOOR, WALL, AND CEILING/
ROOF MUST BE MAINTAINED.

WARNING: DO NOT INSTALL IN SLEEPING ROOM

OF MOBILE HOMES.

A

Figure 12 - Elbow Offset

SuperiorFireplaces.us.com900855-00_B 11

VENTING INSTALLATION Continued

Return
Elbow

Offset
Elbow

Return
Elbow

Offset
Elbow

6' (1.88 m)

Max.

6' (1.88 m)

Max.

Offset
Elbow

Offset
Elbow

Return
Elbow

A B C

Figure 14 - Typical Offset Terminations

FIRESTOP SPACERS (1100EFS-10DM)

Firestop spacers are required at each point where the chimney penetrates
a floor space. Their purpose is to establish and maintain the required
clearance between the chimney and the combustible materials. When
the pipe passes through a framed opening into a living space above, the
firestop must be placed onto the ceiling from below as shown in Figure 15.

They also provide complete separation from one floor space to another
or attic space as required by most codes. When the double wall pipe
passes through a framed opening into an attic space, the firestop must
be placed into an attic floor as shown in Figure 16.

Return

Return
Elbow

6' (1.88 m)

Max.

6' (1.88 m)

Max.

6' (1.88 m)

6' (1.88 m)

Max.

Max.

Elbow

Ceiling

Support Pipe

12S-12DM

Offset
Elbow

IMPORTANT NOTICE
When penetrating a ceiling into an attic, a firestop
thimble (FST10) is required to avoid intrusion by insu­lation and recommended to negotiate a joist.

Firestop Thimble FST10

Existing
Ceiling
Frame

Firestop
Spacer

Screws or
Staples (Min.
of 8)

Figure 15 - Firestop Spacer with Living Space Above Ceiling

Firestop
Spacer

Figure 16 - Firestop Spacer with Attic Space Above Ceiling

Screws or Staples
(Min. of 8)

Existing
Ceiling
Frame

Figure 16a - Firestop Thimble

PENETRATING ROOF

To maintain a 1" clearance to the pipe on a roof with a pitch, a rect­angular opening must be cut.

1. Determine center point through which pipe will penetrate roof.

2. Determine center point of roof. Pitch is distance the roof drops
over a given span, usually 12". A 6/12 pitch means that roof drops
6" for each 12" measured horizontally down from roof rafters.

3. Use roof opening chart (Figure 17, page 13) to determine correct
opening length and flashing required.

4. Remove shingles around opening measured. Cut out this section.

5. Add next sections of pipe until end penetrates roof line. Check
to see that proper clearances are maintained. Extend chimney by
adding sections of double wall pipe until pipe is minimum of 30"
above highest point of roof cutout. Termination and chimney must
extend a minimum of 36" above highest point where it passes
through roof.

SuperiorFireplaces.us.com 900855-00_B12

VENTING INSTALLATION Continued

17"

(432 mm)

Min.

1" (26 mm)

Min

1" (26 mm)

Min

Pitch Slope Opening "A"

Opening "A"

Used Flashing

Max.

30" (762 mm)

1" (26 mm)

Min

Model No.

Flat 0° 17" (432 mm) V6F-10DM

0-6/12 26.6° 19" (483 mm) V6F-10DM

6/12-12/12 45.0° 24" (610 mm) V12F-10DM

Figure 17 - Roof Opening Measurements

Min.

FLASHING INSTALLATION (V6F-10DM OR V12F-10DM)

Determine the flashing to be used with the roof opening chart. Slide
flashing over pipe until base is flat against roof. Replace as many
shingles as needed to cover exposed area and flashing base. Secure
in position by nailing through shingles (see Figure 18). DO NOT NAIL
THROUGH FLASHING CONE.

Installing Flashing on a Metal Roof

When installing the flashing on a metal roof, it is required that putty
tape be used between the flashing and the roof. The flashing must be
secured to the roof using #8 x 3/4" screws and then sealed with roof
coating to prevent leakage through the screw holes. A roof coating
must also be applied around the perimeter of the flashing to provide
a proper seal.

Storm Collar

Overlap Shingles

Flashing

Top and Sides Only

Cone

Nail Only Outer
Perimeter of Flashing

Underlap Shingles at
Bottom

Figure 18 - Flashing Installation

Storm Collar Installation (SC2-1)

Place storm collar over pipe and slide down until it is snug against
the open edge of the flashing (see Figure 19). Apply waterproof caulk
around the perimeter of the collar to provide a proper seal.

Chimney
Pipe

Waterproof
Caulk

Storm
Collar

Flashing

Figure 19 - Storm Collar

SuperiorFireplaces.us.com900855-00_B 13

VENTING INSTALLATION Continued

Terminations/Spark Arrestor

The fireplace system must be terminated with the listed round top or
chase terminations. In any case, refer to the installation instructions
supplied with the termination.

CAUTION: Do not seal openings on the rooftop
flashing. Follow the installation instructions provided
with the termination being used.

Stainless
Inner Flue
Pipe

Secure
Termination
to Outer
Pipe with 3
Screws

Overlap Shingles
(Top and Sides of
Flashing Base)

Figure 20 - Termination

CHASE INSTALLATIONS

Instructions for chase installations are included with the chase style
termination chosen. In a multiple chase installation, be sure to provide
adequate distance between terminations to prevent smoke spillage
from one termination to another. We suggest that terminations be
separated at least 24", center to center and stacked at a vertical height
difference of 18" (see Figure 21).

Note: If a decorative shroud is to be installed, contact the manufac­turer for specifications.

RLT-12D

Level of Flue
Gas Outlet

Waterproof
Caulking

Storm
Collar

Flashing

Underlap
Shingles

10 FOOT RULE

All flue gas outlet chimney terminations must extend a minimum of
3 feet in height above the highest point where it passes through the
roof and must be at least 2 feet above the highest point of the roof
that is within a horizontal distance of 10 feet (see Figure 22).

10'

(3.05 m)

Level of Flue
Gas Outlet

10'

(3.05 m)

2' (0.61 m) Min.

3'

(0.91 m)

Min

2' (0.61 m)

Min.

3'

(0.91 m)

Min

Figure 22 - 10 Foot Rule

SQUARE TOP TERMINATIONS INSTALLATION STL-12D AND
STL-12DMP

1. Construct chase as illustrated in Figure 23. Note: The shortest

vertical side must be at least 30" high and minimum inside di­mension must be at least 19" as shown in Figure 23.

2. Add pipe sections to chimney system as outlined in fireplace
installation instructions until last piece of chimney is a maximum
of 6" below top of chase (see Figure 23).

19"

(483 mm)

30"

(762 mm)

Min.

6" (153 mm) Max.

24" (610 mm)

24" (610 mm)

Figure 21 - Multiple Chase Installation

18" (458 mm)

Min. Typ.

Figure 23 - Constructing Chase

SuperiorFireplaces.us.com 900855-00_B14

INSTALLATION Continued

3. Fabricate a flashing having a 16-1/2" diameter hole centered
over chimney end with a 2" collar around hole (see Figure 24).
Attach noncombustible spacers at each corner and place flash­ing over chase.

4. Secure flashing through sides with 8-penny nails or sheet rock
screws.

5. Place galvanized sleeve through hole in flashing and around last
section of chimney (see Figure 25).

6. Place termination cap over opening and slip stainless steel inner
pipe into stainless steel chimney section. Lower termination as­sembly until cap rests evenly over flashing hole. Secure cap at
each corner with sheet metal screws (see Figure 26).

16-1/2" Diameter

2" Collar

As Required

28 Gauge
Galvanized Steel

Figure 24 - Constructing Chase Top Flashing

1" Spacer

Termination Cap

Note: Do Not Seal
Ventilation Openings

Termination

Sheet Metal Screw

1" Noncombustible
Spacer

Chase Top

1" Space

1/4" Screen

Note: Do Not Seal

Chase Facia

Ventilation Openings

Figure 26 - Securing Termination to Chase Top Flashing with Sheet

Metal Screws

ROUND TOP TERMINATIONS INSTALLATION RLT-12D, AND
RLT-12HT

1. Construct chase as illustrated in Figure 27. Note: The shortest

vertical side must be at least 30" high and the minimum inside
dimension must be at least 19" as shown in Figure 27.

2. Add pipe sections to chimney system as outlined in fireplace
installation instructions until the last piece of chimney is a
minimum of 6" above chase top (see Figure 27).

3. Fabricate a flashing having a 16-1/2" diameter hole centered over
chimney end with a 2" collar around hole (see Figure 28, page 16).

36"

(915 mm)

Min.

Galvanized Sleeve

2" (51 mm) Min.

Figure 25 - Installing Termination Cap

3"

(77 mm)

Min.

Screw

19"

(483 mm) Min.

6" (153 mm) Min.

30"

(762 mm)

Min.

Figure 27 - Constructing Chase

SuperiorFireplaces.us.com900855-00_B 15

INSTALLATION Continued

4. Attach noncombustible spacers at each corner and place flashing
over chase (see Figure 29). Secure flashing through sides with
8-penny nails or sheet rock screws.

5. Place termination cap over opening. Slip stainless steel inner
pipe of termination into inner stainless steel chimney section
(see Figure 30). Place galvanized steel over chimney outlet (see
Figure 31).

6. Attach storm collar where chimney pierces opening in flash­ing. Caulk where storm collar touches outer chimney pipe (see
Figure 31).

16-1/2" Diameter

28 Gauge
Galvanized Steel

Figure 28 - Constructing Chase Top Flashing

1" Noncombustible Spacer

2" Collar

As Required

Chase Top

Note: Do Not Seal
Ventilation Openings

Caulk

Storm Collar

1" Spacer

Chase Top
Flashing

1" Space

"X" Minimum

Double Wall Chimney

"X" Minimum

Figure 31 - Chase Installation

NONCHASE INSTALLATION

1. Slip on proper pitch roof flashing and mount storm collar above
it. Caulk top of storm collar where it contacts outer chimney pipe.

2. Mount round top termination and secure it to outer chimney pipe
with 3 sheet metal screws.

3"

(77 mm)

Min.

Termination Cap

6" (153 mm)

Min.

Chase

Flashing

Termination
Cap

Note: Do Not Seal
Ventilation Openings

Figure 29 - Chase Top Flashing

Outer Pipe

Figure 30 - Installing Termination Cap

1/4" Screen

Chase Facia

Termination

Inner Pipe

1" Space

Sheet Metal Screw

Caulk

Inner Pipe of
Chimney

Overlap Shingles
(Top and Sides)

Figure 32 - Non-Chase Installation

FINISHING FIREPLACE

Combustible materials, such as wallboard, sheet rock, drywall, plywood,
etc. may make direct contact with sides and top around the fireplace
face. It is important that combustible materials do not overlap the face
itself. Brick, glass, tile or other noncombustible materials may overlap
the front face provided they do not obstruct essential openings like
louvered slots or any other opening. When overlapping with a noncom­bustible facing material, use only noncombustible mortar or adhesive.

Storm Collar

Flashing

Underlap
Shingles
(Bottom Only)

SuperiorFireplaces.us.com 900855-00_B16

REFRACTORY PANEL INSTALLATION

WARNING

LIFTING HAZARD

SINGLE -PERSON LIFT COULD

CAUSE INJURY.

USE ASSISTANCE WHEN MOVING

OR LIFTING.

Fireplace models WRT3538WS, WRT3538WH, WRT4043WS and
WRT4043WH, contain a refractory hearth, sides, back, and a metal
grate, factory mounted. The refractories are reinforced with steel, but
can be broken by improper use. Dropping logs on the bottom refractory
and building fires directly against the refractories can cause premature
burnout of these components. The refractories may easily be replaced.

If replacing refractories, follow the instructions below.

IMPORTANT: Installation of Refractory panels should
be done after the fireplace is placed in a permanent
location.

1. Remove grate, screen assemblies and all hardware components
out of the firebox (save hardware components for reinstallation).

2. Open the box containing the refractories and identify them.

3. Install rear refractory panel. This panel has a top and bottom. To
determine which is the top or bottom, match up the pattern on
the rear panel with the left and right sides before installing the
rear panel. Align the left and right panels with the rear panel so
the grout lines line up. Install the retaining bracket and tighten
set screws (Figure 33).

4. Install the right and left refractory panels with the gas line knock­outs oriented down toward the firebox bottom. Install the retaining
brackets and tighten set screws (Figure 34).

5. Position grate retaining brackets toward the rear of the bottom
refractory (see Figure 34). They should be positioned a distance
apart as shown in Figure 33.

6. Install refractory hearth panel, insert the front of the panel tilted
then slowly let the rear portion go down. Make sure the front of the
hearth is flush with the fireplace and the grate retaining brackets
are centered (see Figure 33)

7. Install grate, screen assemblies and all hardware components
removed in step 1.

Retaining
Bracket

Left
Refractory
Panel

Bottom
Refractory
Panel

38” SERIES 12” CENTERS

43” SERIES 14” CENTERS

Figure 33 - Installing Grate Retainers

Rear Refractory Panel

Right

Refractory

Panel

Grate Retainer

Figure 34 - Installing Refractory Panels

WARNING: Risk of fire! Replace grate with IN­NOVATIVE HEARTH PRODUCTS grate only (see Parts,
pages 24 and 25). This grate has been designed to
keep the operation of your fireplace safe and efficient.

INSTALLING SCREEN

1. Slide round end of screen rod into rings at top of screen. Attach one
push-on nut to end of rod before attaching last ring of screen.

2. Insert the round end screen rod into hole on the left and right side
of smoke shelf (Figure 35).

3. Mount flat end of screen rod with #10 x 5/8" to center of smoke
shelf.

4. Install other screen rod in same manner.

SuperiorFireplaces.us.com900855-00_B 17

Hole for screw
to Hold Screen

Rod

Hole for

Screen Rod

Rating Plate

Figure 35 - Installing Fireplace Screen

MASONRY BRICK PANEL INSTALLATION

Fireplace models WRT4038IS, WRT4038IH, WRT4043IS and
WRT4043IH, contain a masonry brick hearth, sides and back. The
masonry brick hearth is factory mounted, the back and sides are
strapped to the back and sides of fireplace. These masonry brick pan­els are reinforced with steel, but can be broken by improper use. The
masonry brick panels may easily be replaced. Follow the instructions
below for installation of sides and rear masonry brick panels or when

replacing entire kit.

IMPORTANT: Installation of masonry brick panels
should be done after the fireplace is placed in a
permanent location.

Front
Cover
Plate

Note: Remove grate, screen assemblies and all hardware components
out of the box prior to installation.

INSTALLATION

1. Make sure masonry brick hearth panel is centered in the firebox

and flush with the front of the fireplace. Be careful not to pinch
your fingers between the panel and firebox (Figure 36). Note: If

replacing entire kit, start with the masonry brick hearth panel,
then follow steps below.

2. Install the left and right masonry brick panels, align flush with

front cover plates and secure them with retaining brackets and
screws (provided), see Figures 36 and 37.

3. Place the provided grate retainers on the masonry brick hearth

as shown in Figure 37 and refer to Figure 33, page 17 for cor­rect distance.

4. Install the rear masonry brick panel last. Place the rear masonry

brick panel against the back of firebox align flush with left and
right masonry brick panels and secure with retaining brackets
and screws (provided) see Figure 37.

Note: Install grate, screen assemblies and all hardware components
into the firebox following steps in reverse from Refractory Panel
Installation, page 17.

Masonry
Brick
Hearth
Panel

Left Masonry
Brick Panel

Figure 36 - Hearth Brick Panel

Retaining
Bracket

Grate Retainer

Rear Masonry

Brick Panel

Right Masonry

Brick Panel

Figure 37 - Installing Masonry Brick Side and Rear Panels

SuperiorFireplaces.us.com 900855-00_B18

OPTIONAL GAS LINE INSTALLATION

Gas line hook up should be done by your supplier or a qualified
service person.

Note: Before you proceed, make sure your gas supply is turned off.
Use only a 1/2" black iron pipe and appropriate fittings.

1. Remove knockout indentation on refractory or firebrick wall lo­cated above refractory hearth floor. Knockout indentation must be
firmly tapped with any solid object such as a 1/2" dowel until it is
released. Remove fragmented portions of refractory (see Figure

38).

2. Remove gas line cover plate located on either side of fireplace and
pull out insulation from gas line conduit sleeve. Save insulation for
reuse. Replace screws.

3. Run a 1/2" black iron gas line into fireplace through the rear at gas
line conduit sleeve (if using a raised platform, add height). Provide
sufficient gas line into fireplace chamber for fitting connection (see
Figure 39).

Note: Secure incoming gas line to wood framing to provide rigidity for

threaded end.

4. Repack insulation around gas line and into sleeve opening. Seal any
gaps between gas line and refractory knockout hole with refractory
cement or commercial furnace cement, Install the gas appliance or
cap-off gas line if desired.

CAUTION: All gas piping and connections must be
tested for leaks after the installation is completed.
After ensuring that the gas valve is on, apply soap and
water solution to all connections and joints. Bubbles
forming show a leak. Correct all leaks at once. DO NOT
USE AN OPEN FLAME FOR LEAK TESTING AND DO NOT
OPERATE ANY APPLIANCE IF A LEAK IS DETECTED.
LEAK TESTING SHOULD BE DONE BY A QUALIFIED
SERVICE PERSON.

Note: An IHP hood must be installed when using an unvented gas
log set (see Accessories on page 29).

WARNING: Do not operate an unvented gas log set in
this fireplace with the chimney removed.

Outside of
Fireplace

Gas Line
Conduit

Insulation

Remove
Knockout

Side
Firebrick
Finished
Side

1/2" Dowel

Outside of
Fireplace

Incoming 1/2"

Gas Line
Conduit

Repack
Insulation

A gas line or gas log lighter may be installed for the purpose of installing
a vented or vent-free decorative gas appliance incorporating an automatic
shutoff device and complying with the Standard for Decorative Gas Ap­pliances for Installation in Vented Fireplaces, ANSI Z21.60 or American
Gas Association draft requirements for Gas Fired Log Lighters for Wood­burning Fireplaces, Draft NO. 4 dated August, 1993.

If you install a decorative gas appliance (vented gas log), the deco­rative gas appliance must comply with the Standard for Decorative
Gas Appliance for Installation in Solid Fuel Burning Fireplaces, ANS
Z21.60 or Z21.84 and shall also be installed in accordance with the
National Fuel Gas Code, ANSI 7223NFPA 54 latest edition.

If you wish to install an unvented (vent-free) gas log set, only unvented
gas log sets which have been found to comply with the standard for
unvented room heaters, ANSI Z21.11.2 are to be installed in this
fireplace.

Black Iron
Pipe

Seal Opening
with
Refractory
Cement

Figure 39 - Gas Line Installation

Side
Firebrick
Finished
Side

Provide Enough
Threaded End for
Fitting Connection

WARNING: If the fireplace has been used for wood­burning, the firebox and chimney must be cleaned
of soot, creosote and ashes be a qualified chimney
cleaner. Creosote will ignite if heavily heated.

WARNING: When using a decorative vented gas log,
the damper must be removed or permanently locked in
the fully open position and the glass doors must be in
the fully open position.

Gas
Conduit
Cover

Brick with
Access Hole

Figure 38 - Gas Line Access

SuperiorFireplaces.us.com900855-00_B 19

GLASS DOOR INSTALLATION

WARNING

This kit is to be installed by a qualified service
technician or other qualified agency in accordance
with the manufacturer's instructions and all codes
and requirements of the Authority Having Jurisdiction
in the USA or Canada. If these instructions are not
followed exactly, a fire or explosion may result,
causing property damage, personal injury, or loss
of life. The qualified agency performing this work
assumes responsibility for this installation.

INSTALLING OPTIONAL GLASS DOOR MODELS 38LBF and 43LBF

Use only the doors that are listed for use with these fireplaces. Use
of other non-listed glass door on these fireplaces may constitute a
potential fire hazard and is not recommended.

Note: Top door rail, and spring clips are provided with the glass
door kit.

1. Using a Phillips screwdriver, remove the three (3) factory
installed screws underneath top front face.

2. Position the door rail and secure it with one (1) of the screws
removed, start from the middle as shown in Figure 40.

3. Using remaining two (2) screws, secure both the spring clips
and the rail for the left and right sides as shown in Figure 40.

4. With bi-fold doors completely folded, insert bottom pivot pin
into pivot hole located near bottom corner of front face opening
and swing door to vertical position making sure top pins slide
into door track. Door is installed when top door pin snaps into
spring clip (see Figure 41).

5. Repeat step 4 for remaining door.

If you find doors do not close properly or do not appear level or
straight, proceed with section on door adjustment.

Fold Door and
Slide Top Pins
Into Track

Figure 41 - Installing Bi-Fold Doors

Spring Clip

Insert Pin into
Spring Clip

Insert
Bottom Pivot
Pin into Hole

Pivot
Hole

Screw

Door rail

Top Face

DOOR ADJUSTMENT

Remove doors and slightly loosen upper spring clips. Replace
doors and fully close them. Use 1/8" shims (any material) to
level doors. Once proper setting is achieved, carefully open
doors enough so that you can access spring clips with a Phillips
screwdriver. Tighten screws. See Figure 42.

Spring
Clip

Figure 42 - Adjusting Bi-Fold Doors

Figure 40 - Installing Door Rail

SuperiorFireplaces.us.com 900855-00_B20

GLASS DOORS

OPERATION AND MAINTENANCE GUIDELINES

WARNING

HOT GLASS WILL CAUSE BURNS. DO NOT
TOUCH GLASS UNTIL COOLED.
ALLOW CHILDREN TO TOUCH GLASS.

• Fireplaces surfaces get EXTREMELY HOT!

• Install only when fireplace is OFF and COLD.

• The glass on the front of the fireplace reaches EXTREMELY
HIGH temperatures and can cause severe burns if touched.
Even after the gas is turned off, fireplace surfaces remain
extremely hot.

• Keep children away from an operating fireplace. Closely
supervise children in any room where a fireplace is operating
to prevent contact with glass.

Glass doors are optional with the fireplace. When fireplace is in
operation, doors must be fully opened or fully closed position only
or a fire hazard may be created (see Figure 43).

A fireplace equipped with glass doors operates much differently
than a fireplace with an open front. A fireplace with glass doors has
a limited amount of air for combustion.

Excessive heat within the fireplace can result if too large a fire is built
or if combustion air gate is not completely open. The following tips
should be followed to assure that both the fireplace and glass door
retain their beauty and function properly. Both the flue damper and
glass doors must be fully opened before starting fire. This will provide
sufficient combustion air and maintain safe temperatures in firebox.

IMPORTANT: The glass must be allowed to warm slowly and evenly.
The tempered glass will withstand a gradual temperature rise to 550°
F, which is more than a normal fire will generate. Such materials as
pitch/wax laden logs, very dry mill end lumber and large amounts
of paper or cardboard boxes can create an excessively hot fire and
should not be burned in this fireplace. Always keep the fire well back
from the doors and never allow flames to contact the glass.

NEVER

Doors Fully Closed

Fireplace Front

Doors Fully Opened

Fireplace Front

Figure 43 - Bi-Fold Glass Doors

Cleaning Glass

Clean glass with any commercial glass cleaner or soap and water. Do
not use any abrasive material to clean glass. Do not clean glass with any
cool water if glass is still hot from the fire and smoke.

WARNING: Fireplaces equipped with glass doors
should be operated only with doors fully opened or
doors fully closed. Doors, if left partly open, may draw
gas and flame out of the fireplace opening creating
risks of both fire and smoke.

WARNING: Do not slam or strike doors. Damage
can result in a hazardous condition.

WARNING: Discontinue use of the appliance imme­diately if doors are damaged and contact a qualified
installer for repair. Only doors certified with the ap­pliance shall be used.

SuperiorFireplaces.us.com900855-00_B 21

OPERATION AND MAINTENANCE GUIDELINES Continuation

STARTING A FIRE

1. To properly start a fire in a the fireplace, first check the operation
of the flue damper (see “DAMPER CONTROL” and Figure 44, below).

2. To prevent smoke at startup, close all windows near the fireplace
when first lighting a fire. The closed windows may be reopened once
a chimney draft is drawn in the fireplace.

3. Center the grate in the firebox on or over the bottom hearth so the
fire can breathe properly. Crumble and twist plenty of newspapers
UNDER the grate, and criss-cross some small, dry kindling sticks on
top of the paper or on the bottom of the grate.

4. Build a pyramid of three split logs (split wood will light more
quickly). Arrange the logs to provide plenty of air space between them.

5. Light the paper at both sides of the firebox.

6. Close the screens to prevent the escape of sparks and embers.

7. Close the damper only when the fire is completely OUT and ashes
are COLD. Keep the damper closed when the fireplace is not in use,
to prevent unnecessary loss of conditioned room air.

DAMPER CONTROL AND OUTSIDE AIR KIT OPERATION

The damper handle, which opens and closes the damper blade, is
located in the upper front face of the fireplace. Pushing the handle
forward and up through the keyway slot will free damper blade to
automatically open. Pushing the handle forward and down will lock
damper blade closed (see Figure 44). Damper must be locked in the
full open position before operating fireplace (see Figure 44).
Outside air kit handle is located at left hand side of fireplace. Pulling
handle out will free outside air door to open. Pushing handle in will
lock door closed.

To Close
Damper

Damper
Weight

Damper
Weight

To Open
Damper

Figure 44 - Operating Damper Handle

SuperiorFireplaces.us.com 900855-00_B22

IMPORTANT NOTICES - CANADA

TECHNICAL SERVICE

IMPORTANT NOTICE
A manufactured shroud which has been approved by a
national testing agency for use with this fireplace may
be used if installed in accordance with the instructions
by its manufacturer. A locally fabricated shroud may be
used with IHP Shroud Leg Spacer Kit (SLK) in accor­dance with instructions provided with the shroud.

NOTICE: The firebox canopy (hood) must not be mod­ified or replaced with a canopy that may be provided
with the unvented decorative room heater.

CAUTION: THE STRUCTURAL INTEGRITY OF THE
MANUFACTURED HOME FLOOR, WALL, AND CEIL­ING/ROOF MUST BE MAINTAINED.

WARNING: DO NOT INSTALL IN SLEEPING ROOM

OF MOBILE HOMES.

Canadian code CAN/ULC-S610-M87 and other pertinent codes require stain­less steel chimney for the installation of this fireplace. A Cold Air Climate Kit is
also required in Canada and is recommended for cooler regions in the United
States. Below, find a list of approved stainless steel parts.

You may have further questions about installation, operation, or
troubleshooting. Please contact your IHP dealer for any questions
or concerns a. When contacting your dealer please have your model
and serial numbers of your fireplace ready. You can also visit our web

site at SuperiorFireplaces.us.com.

REPLACEMENT PARTS

See Pages 24 to 27 for a complete replacement parts list. Use only
parts supplied from the manufacturer.

Normally, all parts should be ordered through your IHP distributor
or dealer. Parts will be shipped at prevailing prices at time of order.

When ordering repair parts, always give the following information:

1. The model number of the fireplace.

2. The serial number of the fireplace.

3. The part number.

4. The description of the part.

5. The quantity required.

6. The installation date of the fireplace.

If you encounter any problems or have any questions concerning the
installation or application of this fireplace, please contact your dealer.

IHP
1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
Visit us at SuperiorFireplaces.us.com

Chimney Parts List for Canada

Catalog
No.

F0953 12-12HT 12" Section Double Wall Pipe

F0954 18-12HT 18" Section Double Wall Pipe

F0955 24-12HT 24" Section Double Wall Pipe

F0956 36-12HT 36" Section Double Wall Pipe

F0957 48-12HT* 48" Section Double Wall Pipe

F0958 30E-12HT 30" Offset and Return

F0959 12S-12HT Chimney Support

F0960 RLT-12HT* Round Top w/ Louvers

F0961 AP-12HT Anchor Plate/Collar Assembly (Masonry Fireplaces)

F0951 CAK-12 Cold Air Collar Kit

*When ordered alone, this part cannot ship via parcel delivery services.

Model
No.

12" Hi-Temp
Wood-burning Chimney

SuperiorFireplaces.us.com900855-00_B 23

PARTS

2

1 (4)

3

5

4

MODEL CATALOG NO.

WRT3538WS F3412
WRT3538WH F3413
WRT4038IS F3414
WRT4038IH F3415
WRT3543WS F3416
WRT3543WH F3417
WRT4043IS F3418
WRT4043IH F3419

10

11

6

12

14 (3)

17

7

13

16

30

8
(2)

9
(2)

24

29

23

28

25

26

27

15

22

20
(2)

33

(2)

21

18

19

32 (2)

31 (2)

34

SuperiorFireplaces.us.com 900855-00_B24

PARTS

This list contains replaceable parts used in your firebox. When ordering parts, follow the instructions listed under Replacement Parts on
page 23 of this manual.

WARNING: Contact an IHP dealer to obtain any of these parts. Never use substitute materials not approved

by IHP. Use of non-approved parts can result in poor performance and safety hazards.

KEY NO. CATALOG NO. DESCRIPTION

1 ** Spacer, Top • • 4
2 J6998 Collar, Starter • • 1
3 ** Top Casing, LBR38 • 1

** Top Casing, LBR43 • 1

4 ** Insulation Top, LBR38 • 1

** Insulation Top, LBR43 • 1

5 ** Assembly, Plenum LBR38 • 1

** Assembly, Plenum LBR43 • 1

6 ** Wrapper Casing, LBR38 • 1

** Wrapper Casing, LBR43 • 1
7 ** Assembly Gate, Outside Air • • 1
8 J6934 Plate Cover, Gas Line • • 2
9 ** Conduit, Gas Line LBRS • 2
10 ** Insulation, Dome • • 1
11 ** Assembly Dome, LBR38 • 1

** Assembly Dome, LBR43 • 1
12 ** Assembly, Lintel Extension LBR38 • 1

** Assembly, Lintel Extension LBR43 • 1
13 J4359 Bracket, Damper Rod • • 1
14 ----- See Pages 26 and 27 • • 1
15 ----- See Pages 26 and 27 • • 1
16 ----- See Pages 26 and 27 • • 1
17 ----- See Pages 26 and 27 • • 1
18 ----- See Pages 26 and 27 • • 1
19 ** Bracket, Shipping • • 1
20 H4035 Bracket, Grate • • 2
21 ** Cover Plate Side • • 1
22 ** Cover Plate Side • • 1
23 ** Wrapper Firebox, LBR38 • 1

** Wrapper Firebox, LBR43 • 1
24 ** Duct, Air • • 1
25 ** Plate Cover, Outside Air Rod • • 1
26 ** Cover Actuator • • 1
27 ** Label, Usage • • 1
28 ** Assembly Base, LBR38 • 1

** Assembly Base, LBR43 • 1
29 ** Lip, Ash LBR38 • 1

** Lip, Ash LBR43 • 1
30 ** Assembly, Front Face Frame LBR38 • 1

** Assembly, Front Face Frame LBR43 • 1
31 16M29 Rod, Screen LBR38 • 2

16M30 Rod, Screen LBR43 • 2
32 F3441 Nut, Push-On • • 2
33 16M27 Panel Screen/Pull, LBR38 • 2

16M28 Panel Screen/Pull, LBR43 • 2
34 J4381 Assembly Grate C36 • 1

J4382 Assembly Grate C42 • 1

** Not a field replaceable part.

38" 43"

QTY.

SuperiorFireplaces.us.com900855-00_B 25

PARTS

This list contains replaceable parts used in your firebox. When ordering parts, follow the instructions listed under Replacement Parts on
page 23 of this manual.

WARNING: Contact an IHP dealer to obtain any of these parts. Never use substitute materials not approved

by IHP. Use of non-approved parts can result in poor performance and safety hazards.

WARNING

LIFTING HAZARD

SINGLE -PERSON LIFT COULD

CAUSE INJURY.

USE ASSISTANCE WHEN MOVING

OR LIFTING.

CATALOG NO. DESCRIPTION

F3433 Kit, 38" White Stk Refractory Panels
F3434 Kit, 38" White HB Refractory Panels
F3437 Kit, 43" White Stk Refractory Panels
F3438 Kit, 43" White HB Refractory Panels

1

6

3

IMPORTANT: Installation of refractory panels should
be done after the fireplace is placed in a permanent
location.

CATALOG NO. DESCRIPTION

F3435 Kit, 38" Ivory Split Stk Masonry Panels
F3436 Kit, 38" Ivory Split HB Masonry Panels
F3439 Kit, 43" Ivory Split Stk Masonry Panels
F3440 Kit, 43" Ivory Split HB Masonry Panels

1

6

3

5

2

2

4

5

4

Stacked Refractory Split HB Masonry

SuperiorFireplaces.us.com 900855-00_B26

PARTS

KEY
NO. CAT. NO. DESCRIPTION 38" (Stk) 43" (Stk) 38" (HB) 43" (HB) QTY.

1

2 --- Refractory, Bottom LBR38 • 1
3 --- Refractory, Left and Right RB • 1
4 --- Refractory, Left and Right RB • 1
5 --- Refractory, Rear RB • 1
6 --- Retainer Refractory • 3

1 F3437 Kit, 43" White Stk Refractory Panels • 1

2 --- Refractory, Bottom LBR43 • 1
3 --- Refractory, Left and Right RB • 1
4 --- Refractory, Left and Right RB • 1

5 --- Refractory, Rear RB • 1
6 --- Retainer Refractory • 3

1 F3434 Kit, 38" White HB Refractory Panels • 1

2 --- Refractory, Bottom LBR38 • 1
3 --- Refractory, Left HB • 1
4 --- Refractory, Right HB • 1
5 --- Refractory, Rear HB • 1
6 --- Retainer Refractory • 3

1 F3438 Kit, 43" White HB Refractory Panels • 1

2 --- Refractory, Bottom LBR43 • 1
3 --- Refractory, Left HB • 1
4 --- Refractory, Right HB • 1
5 --- Refractory, Rear HB • 1
6 --- Retainer Refractory • 3

F3433

Kit, 38" White Stk Refractory Panels • 1

KEY
NO. CAT. NO. DESCRIPTION 38" (Split Stk) 43" (Split Stk) 38" (Split HB) 43" (Split HB) QTY.

1

2 --- Assembly, Hearth, Cut LBR38 Ivory • 1
3 --- Assembly, Panel, Left Cut Ivory SRB • 1
4 --- Assembly, Panel, Right Cut Ivory SRB • 1
5 --- Assembly, Panel, Rear Cut Ivory SRB • 1
6 --- Retainer Refractory • 3

1 F3439 Kit, 43" Ivory Split Stk Masonry Panels • 1

2 --- Assembly, Hearth, Cut LBR43 Ivory • 1
3 --- Assembly, Panel, Left Cut Ivory SRB • 1
4 --- Assembly, Panel, Right Cut Ivory SRB • 1

5 --- Assembly, Panel, Rear Cut LBR43 SRB • 1
6 --- Retainer Refractory • 3

1 F3436 Kit, 38" Ivory Split HB Masonry Panels • 1

2 --- Assembly, Hearth, Cut LBR38 Ivory • 1
3 --- Assembly, Panel, Left Cut Ivory SHB38 • 1
4 --- Assembly, Panel, Right Cut Ivory SHB38 • 1
5 --- Assembly, Panel, Rear Cut Ivory SHB38 • 1
6 --- Retainer Refractory • 3

1 F3440 Kit, 43" Ivory Split HB Masonry Panels • 1

2 --- Assembly, Hearth, Cut LBR43 Ivory • 1
3 --- Assembly, Panel, Left Cut Ivory SHB43 • 1
4 --- Assembly, Panel, Right Cut Ivory SHB43 • 1
5 --- Assembly, Panel, Rear Cut Ivory SHB43 • 1
6 --- Retainer Refractory • 3

F3435

Kit, 38" Ivory Split Stk Masonry Panels • 1

SuperiorFireplaces.us.com900855-00_B 27

ACCESSORIES

CAT NO. MODEL DESCRIPTION

BI-FOLD GLASS DOORS

F3420 38LBF Bi-Fold Door, 38WB Black

F3421 43LBF Bi-Fold Door, 43WB Black

DOUBLE WALL PIPE

F0932 12-12DM 12" Section Double Wall Pipe Snap Lock

F0933 18-12DM 18" Section Double Wall Pipe Snap Lock

F0934 24-12DM 24" Section Double Wall Pipe Snap Lock

F0935 36-12DM 36" Section Double Wall Pipe Snap Lock

F0936 48-12DM 48" Section Double Wall Pipe Snap Lock

F0953 12-12HT 12" Section Hi-Temp Double Wall Pipe Snap Lock

F0954 18-12HT 18" Section Hi-Temp Double Wall Pipe Snap Lock

F0955 24-12HT 24" Section Hi-Temp Double Wall Pipe Snap Lock

F0956 36-12HT 36" Section Hi-Temp Double Wall Pipe Snap Lock

F0957 48-12HT 48" Section Hi-Temp Double Wall Pipe Snap Lock

30° OFFSET AND RETURN

F0937 30E-12DM 30 Degree Offset and Return

F0958 30E-12HT 30 Degree Hi-Temp Offset and Return

OPTIONAL OUTSIDE AIR KIT FOR FLOOR INSTALLATION

F1091 AK4 Complete Outside Air Kit w/Collars Hood & 3' Flex

OPTIONAL OUTSIDE AIR KIT FOR SIDEWALL INSTALLATION

F1093 AK4F Outside Air Kit Collar, Hood & 3' Flex for Floor Venting

STORM COLLAR

F0946 SC2-1 Storm Collar

EMBER PROTECTOR

J6906 Ember Protector

FIRESTOP SPACER

J4384 1100EFS-10DM 1" Clearance Firestop Spacer

SuperiorFireplaces.us.com 900855-00_B28

ACCESSORIES Continued

900599-01

ROOF FLASHING

F0942 V6F-10DM Roof Flashing 0 to 6/12 Pitch

F0943 V12F-10DM Roof Flashing 6/12 to 12/12 Pitch

SQUARE CHASE-TOP TERMINATION

F0948 STL-12D Square Top Termination with Slip Section

F0949 STL-12DMP

Square Top Termination with Slip Section (Pre-Painted
Black)

ROUND TOP TERMINATIONS

F0947 RLT-12D Round Top Termination with Louvered Screen

F0960 RLT-12HT Hi-Temp Round Top Termination with Louvered Screen

FIRESTOP THIMBLE

F0944 FST10 Firestop Thimble

LABEL-UL127-50PK

F2659

LABEL-UL127-

50PK

UL127 Venting Label - 50 PK

ADJUSTABLE HOOD

Required when installing a vent-free gas log in this fireplace.

WARNING
HOT

•Fire Risk

•Insulation and combustibles must not touch

pipe

•Consult manual for clearance requirements

•Ensure proper connection

WARNING
HOT

•Fire Risk

•Insulation and combustibles must not touch

pipe

•Consult manual for clearance requirements

•Ensure proper connection

WARNING
HOT

•Fire Risk

•Insulation and combustibles must not touch

pipe

•Consult manual for clearance requirements

•Ensure proper connection

F1764 GA6050 Black Fireplace Hood

SuperiorFireplaces.us.com900855-00_B 29

NOTES

______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________

_____________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________

SuperiorFireplaces.us.com 900855-00_B30

Innovative Hearth Products

®

Superior

Brand Wood-Burning Fireplace

20 Year Limited Warranty

THE WARRANTY

Innovative Hearth Products ("IHP") 20 Year Limited Warranty warrants your Superior® Brand wood burning fireplace ("Product") to be free from defects in materials and
workmanship at the time of manufacture. The Product body, firebox and ceramic glass carry the 20 Year Limited Warranty. Ceramic glass carries the 20 Year Limited Warranty
against thermal breakage only. After installation, if covered components manufactured by IHP are found to be defective in materials or workmanship during the 20 Year Limited
Warranty period and while the Product remains at the site of the original installation, IHP will, at its option, repair or replace the covered components. If repair or replacement
is not commercially practical, IHP will, at its option, refund the purchase price or wholesale price of the IHP product, whichever is applicable. IHP will also pay IHP prevailing
labor rates, as determined in its sole discretion, incurred in repairing or replacing such components for up to five years. THERE ARE EXCLUSIONS AND LIMITATIONS to this
20 Year Limited Warranty as described herein.

COVERAGE COMMENCEMENT DATE

Warranty coverage begins on the date of purchase. In the case of new home construction, warranty coverage begins on the date of first occupancy of the dwelling or six
months after the sale of the Product by an independent IHP dealer/distributor, whichever occurs earlier. The warranty shall commence no later than 24 months following the
date of product shipment from IHP, regardless of the installation or occupancy date.

EXCLUSIONS AND LIMITATIONS

This 20 Year Limited Warranty applies only if the Product is installed in the United States or Canada and only if operated and maintained in accordance with the printed instruc­tions accompanying the Product and in compliance with all applicable installation and building codes and good trade practices.

This warranty is non-transferable and extends to the original owner only. The Product must be purchased through a listed supplier of IHP and proof of purchase must be
provided. The Product body and firebox carry the 20 Year Limited Warranty from the date of installation. Vent components, trim components, paint and applied stains are
excluded from this 20 Year Limited Warranty. The following do not carry a 20 Year Limited Warranty but are warranted as follows:

Air tubes, baffles and brick retainers – Repair or replacement for one year from the date of installation
Cast iron parts – Replacement for one year from date of installation
Catalyst – Carries a separate warranty. Refer to the warranty certificate provided for that part
Electrical components – Repair or replacement for one year from the date of installation
Fireplace screens, refractory and side shields (metal or refractory) – Repair or replacement for two years from date of installation. Excludes hairline cracks.
Fuel grates –These parts are considered consumable accessories and therefore are not warranted, with the exception of defects in material or workmanship which

are covered for 90 days from the date of installation
Gaskets – Replacement for one year from date of installation
Gold & nickel plating – Replacement for two years from date of installation. Excludes tarnishing

Optional glass doors – Repair or replacement for 90 days from the date of installation
Refractory & screens – Replacement for two years from date of installation. Excludes hairline cracks
Removable air tubes – Repair or replacement for seven years from date of installation. IHP prevailing labor rates for years one through five.

Labor coverage – Prevailing IHP labor rates apply for the warranty period of the component.
Parts not otherwise listed carry a 90 day warranty from the date of installation.
Whenever practicable, IHP will provide replacement parts, if available, for a period of 10 years from the last date of manufacture of the Product.

IHP will not be responsible for: (a) damages caused by normal wear and tear, accident, riot, fire, flood or acts of God; (b) damages caused by abuse, negligence, misuse, or
unauthorized alteration or repair of the Product affecting its stability or performance. (The Product must be subject to normal use with approved fuels listed in the Operation
Manual provided with the product. This includes burning such fireplace fuels as wood and natural or propane gas. Fuel products with abnormal burning characteristics,
including but not limited to fuel such as driftwood, coal or plywood and wood products using a binder may burn at excessive temperatures and may cause damage to the
Product or may cause it to function improperly.); (c) damages caused by failing to provide proper maintenance and service in accordance with the instructions provided with
the Product; (d) damages, repairs or inefficiency resulting from faulty installation or application of the Product.

Coverage of this 20 Year Limited Warranty is conditional upon use of an adequate fuel grate on factory-built fireplaces only, when applicable.
IHP is not responsible for inadequate fireplace system draft caused by air conditioning and heating systems, mechanical ventilation systems, or general construction condi­tions which may generate negative air pressure in the room in which the appliance is installed. Additionally IHP assumes no responsibility for smoking conditions caused by
inadequate chimney height, adjoining trees or buildings, adverse wind conditions or unusual environmental factors and conditions. Certain IHP Products are listed for use with
Security Chimneys International, Ltd. or IHP chimney systems only. Use of chimney components other than that specified in the Product manual will void the Product warranty.

This 20 Year Limited Warranty covers only parts and labor as provided herein. In no case shall IHP be responsible for materials, components or construction which are not
manufactured or supplied by IHP or for the labor necessary to install, repair or remove such materials, components or construction. Additional utility bills incurred due to any
malfunction or defect in equipment are not covered by this 20 Year Limited Warranty. All replacement or repair components will be shipped F.O.B. from the nearest stocking
IHP factory.

LIMITATION ON LIABILITY

It is expressly agreed and understood that IHP’s sole obligation and the purchaser’s exclusive remedy under this warranty, under any other warranty, expressed or implied, or
in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified herein.

In no event shall IHP be liable for any incidental or consequential damages caused by defects in the Product, whether such damage occurs or is discovered before or after
replacement or repair, and whether such damage is caused by IHP’s negligence. IHP has not made and does not make any representation or warranty of fitness for a particular
use or purpose, and there is no implied condition of fitness for a particular use or purpose.

IHP makes no expressed warranties except as stated in this 20 Year Limited Warranty. The duration of any implied warranty is limited to the duration of this expressed warranty.

No one is authorized to change this 20 Year Limited Warranty or to create for IHP any other obligation or liability in connection with the Product. Some states and provinces
do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. The provisions of this 20 Year
Limited Warranty are in addition to and not a modification of or subtraction from any statutory warranties and other rights and remedies provided by law.

INVESTIGATION OF CLAIMS AGAINST WARRANTY

IHP reserves the right to investigate any and all claims against this 20 Year Limited Warranty and to decide, in its sole discretion, upon the method of settlement.

To receive the benefits and advantages described in this 20 Year Limited Warranty, the appliance must be installed and repaired by a licensed contractor approved by IHP.
Contact IHP at the address provided herein to obtain a listing of approved dealers/distributors. IHP shall in no event be responsible for any warranty work done by a contrac-

tor that is not approved without first obtaining IHP's prior written consent.

HOW TO REGISTER A CLAIM AGAINST WARRANTY

In order for any claim under this warranty to be valid, you must contact the IHP dealer/distributor from which you purchased the product. If you cannot locate the dealer/
distributor, then you must notify IHP in writing. IHP must be notified of the claimed defect in writing within 90 days of the date of failure. Notices should be directed to the IHP
Warranty Department at 1769 East Lawrence Street; Russellville, AL 35654 or visit our website at WWW.SUPERIORFIREPLACES.US.COM.

Printed in U.S.A. © 2013 Innovative Hearth Products

P/N 900224-00, Rev. B 02/2018

SuperiorFireplaces.us.com900855-00_B 31

Innovative Hearth Products
1769 East Lawrence Street • Russellville, AL 35654

SuperiorFireplaces.us.com

P900855-00

Record the following important information about your fireplace:

Fireplace model number

Fireplace serial number

Date fireplace was Installed

Dealer name

Innovative Hearth Products reserves the right to make changes at any time, without notice, in
design, materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.

Printed in U.S.A. © 2017 Innovative Hearth Products LLC
P/N 900855-00 Rev. B 02/2018

1769 East Lawrence Street • Russellville, AL 35654