Superior VRT4032WS, VRT4032WH, VRT4036WS, VRT4036WH, VRT4042WS Installation And Operation Instructions Manual

Installation and Operation Instructions

Unvented (Vent-Free) Universal Firebox

P/N 126709-01 REV. B 01/2017

Models

PFS

P126709-01

Report No. F09-130

®

US

VRT4032WS VRT4032WH

For use with log set (required option)

VRT4036WS VRT4036WH

LBG18BM

VRT4042WS VRT4042WH

INSTALLER: Leave this manual with the appliance. CONSUMER: Retain this manual for future reference.

WARNING: Carefully review the instructions supplied with the decorative type unvented room heater for

the minimum ﬁ replace size requirement. DO NOT INSTALL THE APPLIANCE IN THIS FIREBOX, UNLESS THIS FIREBOX MEETS THE MINIMUM

DIMENSIONS REQUIRED FOR THE INSTALLATION.

With Refractory Panels

WARNING: FOR USE ONLY WITH A LISTED, GAS-FIRED UNVENTED DECORATIVE ROOM HEATER NOT TO EXCEED 40,000 BTU/H.

DO NOT BUILD A WOOD FIRE.

WARNING:

FIRE OR EXPLOSION HAZARD Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

- Do not store or use gasoline or other ﬂ ammable vapors and liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁ re department.

- Installation and service must be performed by a qualiﬁ ed installer, service agency or the gas supplier.

TABLE OF CONTENTS

Safety .................................................................. 2

Local Codes......................................................... 3

Product Features ................................................. 4

Locating Firebox .................................................. 4

Product Speciﬁ cations ......................................... 5

Air For Combustion and Ventilation ..................... 7

Installation ........................................................... 9

Replacement Parts ............................................ 14

Technical Service...............................................14

Accessories ....................................................... 15

Parts .................................................................. 16

Warranty ............................................................20

SAFETY

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to this manual for correct installation and operational procedures. For assistance or additional information consult a qualiﬁ ed installer, service agency or the gas supplier.

This appliance may be installed in an aftermarket,* permanently located, manufactured (mobile) home, where not prohibited by local codes.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

This ﬁ rebox has been tested under Z21.91b-2007 for use with approved ANSI Z21.1 1.2 decorative type unvented room heater .

IMPORT ANT: Read this owner’s manual carefully and completely before trying to assemble, operate or service this ﬁ replace. Improper use of this ﬁ replace can cause serious injury or death from burns, fire, explosion, electrical shock and carbon monoxide poisoning.

DANGER: Carbon monoxide

poisoning may lead to death!

WARNING: Any change to this heater or its controls can be dangerous.”

WARNING: Do not use a blower insert, heat exchanger insert or other accessory not approved for use with this ﬁ rebox.

W ARNING: If the information in this manual is not followed exactly, a ﬁ re or explosion may result causing property damage, personal injury or loss of live

SuperiorFireplaces.US.com

WARNING: Do not allow fans to blow directly into the ﬁ rebox. Avoid any drafts that alter burner ﬂ ame patterns. Ceiling fans can create drafts that alter burner ﬂ ame patterns. Altered burner patterns can cause sooting.

Due to high temperatures, the appliance should be located out of trafﬁ c and away from furniture and draperies.

126709-01B2

SAFETY

Continued

Do not place clothing or other ﬂ ammable material on or near the appliance. Never place any objects in the ﬁ rebox or on logs.

Firebox front and screen becomes very hot when running ﬁ rebox. Keep children and adults away from hot surfaces to avoid burns or clothing ignition. Firebox will remain hot for a time after shutdown. Allow surfaces to cool before touching.

Keep the ﬁ replace area clear and free from combustible materials, gasoline, and other ﬂ ammable vapors and liquids.

You must operate this ﬁ replace with the provided fireplace screen and hood in place. Make sure these parts are in place and screens are closed before running installed gas log heater. Replace hood with INNOV ATIVE HEARTH PRODUCTS cat. no. J4350 - 50", cat. no. J4351 - 42", or cat. no. J4352 - 36" only . This hood has been designed to keep the operation of your ﬁ replace safe and efﬁ cient.

1. Do not use this ﬁ rebox as a wood burning ﬁ replace. Use only decorative unvented

room heaters (log sets).

2. Do not add extra logs or ornaments such as pine cones, vermiculite or rock wool. Using these added items can cause sooting.

3. Use only the provided hood. See Parts, Page 18. The firebox canopy (hood) must not be modiﬁ ed or replaced with a canopy (hood) that may be provided with the unvented decorative room heater.

4. Vent-free gas log heaters installed in these ﬁ reboxes require fresh air ventilation to run properly . See Air for Combustion and Ventilation, Page 8.

5. Do not run vent-free heaters installed in these ﬁ reboxes

• where ﬂ ammable liquids or vapors are

used or stored

• under dusty conditions

6. Do not use this ﬁ rebox to cook food or burn paper or other objects.

7. Turn unit off and let cool before servicing. Only a qualiﬁ ed service person should service and repair ﬁ rebox.

8. Operating vent-free heaters installed in these ﬁ reboxes above elevations of 4,500 feet could cause pilot outage.

9. Do not use the ﬁ rebox if it has been under water.

10. Before using furniture polish, wax, carpet cleaner or similar products, turn heater off. If heated, the vapors from these products may create a white powder residue within burner box or on adjacent walls and furniture.

11. Provide adequate clearances around air openings.

Children and adults should be alerted to the hazard of high surface temperature and should stay away to avoid burns or clothing ignition.

Y oung children should be carefully supervised when they are in the same room with the appliance.

126709-01B 3

SuperiorFireplaces.US.com

LOCAL CODES

Install and use ﬁ rebox with care. Follow all local codes. In the absence of local codes, use the latest edition of The National Fuel Gas Code

ANSI Z223.1/NFPA 54*; National Fuel Gas Code; Natural Gas and Propane Installation Code. Firebox must be electrically grounded in accordance with the National Electrical Code, ANSI/NFP A 70 (latest edition).

COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS

These appliances are approved for installation in the US state of Massachusetts if the following additional requirements are met:

• Un-vented Room Heaters shall be installed in accordance with 527 CMR 30.

• Installation and repair must be done by a plumber or gas ﬁ tter licensed in the Common- wealth of Massachusetts.

• The ﬂ exible gas line connector used shall not exceed 36 inches (92 centimeters) in length.

• The individual manual shut-off must be a T-handle type valve.

• Unvented appliances may NOT be installed in bedrooms or bathrooms.

• A working smoke detector must be installed in the area where vent-free appliances are installed.

Seller of unvented propane or natural gas-ﬁ red supplemental room heaters shall provide to each purchaser a copy of 527 CMR 30 upon sale of the unit.

*Available from:

American National Standards Institute, Inc.

25 West 43rd Street, 4th ﬂ oor

New York, NY 10036

National Fire Protection Association, Inc.

1 Batterymarch Park

Quincy, MA 02169-7471

PRODUCT FEATURES

OPERATION

This ﬁ rebox has been tested and approved under ANSI Z21.91 for use with any gas log approved to ANSI Z21.11.2 for indoor applications and ANSI Z21.97 for outdoor applications. (Physical size limitations apply. Refer to minimum ﬁ rebox requirements sup- plied with log heater.) It requires no outside venting or chimney making installation easy and inexpensive. When used without blower, heater installed in ﬁ rebox requires no electric- ity making it ideal for emergency backup heat.

LOCATING FIREBOX

PLANNING

Plan where you will install the ﬁ rebox. This will save time and money later when you install the ﬁ rebox. Before installation, consider the following:

1. Where ﬁ rebox will be located: Allow for wall and ceiling clearances (see Installa-

tion Clearances, Page 10).

2. Everything needed to complete ﬁ replace installation.

REFRACTORY BRICK LINER

Your ﬁ rebox may feature a concrete refractory brick liner. As with all concrete liners, this liner may develop slight cracks when exposed to heat. These cracks will not affect performance of ﬁ replace or vent-free gas logs.

OUTSIDE AIR KIT ACCESSORY

An optional AK4 air kit provides additional outdoor air to improve burner efﬁ ciency and reduce build-up of condensation in the living space. Follow instructions included with air kit.

3. These models CANNOT be installed in a bedroom unless maximum Btu rating of installed vent-free log set is less than 10,000 Btu/hr.

4. Proper air for combustion and ventilation

(Page 7).

SuperiorFireplaces.US.com

126709-01B4

237/8"

35/8"

17

3

/8"

291/2"

34

1

/2"

36

3

/8" Indoor

37

3

/8" Indoor/Outdoor

Standoffs

221/2"

321/4"

361/2"

35/8"

8

1

/8"

41/4"

Built-In Side Nailing Flanges

5/8"

32" MODELS

9"

93/4"

19 3/8 "

16 5/8"

15/8"

3

5

/8"

8

1

/8"

2 7/8"

85/8" Indoor

8

1

/4" Indoor/Outdoor

Built-I Side Nailin Flang

Square Gas Line Access Holes

Left Side View with Air Kit

Outside Air Kit Location (Optional)

PRODUCT SPECIFICATIONS

1

8

/8"

10

1

/2"

1

8

/8"

Firebox Top View

3 5/8"

1

/2"

3

/4"

9

Right Side View

Top View

Front View

126709-01B 5

Figure 1 - Firebox Dimensions (32" Models)

SuperiorFireplaces.US.com

Back View

20 1/2"

(36" Models)

24

1

/8"

(42" Models)

5

/8"

2 5/8"

26

3

/4" (36" Models)

29

5

/8" (42" Models)

35" (36" Models) 42" (42" Models)

40" (36" Models)

44

1

/

4

" (42" Models)

43"(36" Models)

51

1

/8"(42" Models)

29

1

/8" (36" Models)

36

1

/8" (42" Models)

41

1

/8"(36" Models)

48

1

/4"(42" Models)

5/8"

36

1

/

8

" (36" Models)

40" (42" Models)

Built-In Side Nailing Flanges

PRODUCT SPECIFICATIONS

13 3/4" (36" Models) 12

3

/8" (42" Models)

7

1

/4" (36" Models)

9" (42" Models)

2

5

/8"

10

1

/2"

(36" Models)

12

1

/2"

(42" Models)

13 3/4" (36" Models) 15

5

/8" (42" Models)

2

5

/8"

3

7

/8"

8

1

/8"

(36" Models)

9"

(42" Models)

21

1

/8" (36" Models)

23

1

/8" (42" Models)

Built-In Side Nailing Flange

Continued

36" AND 42" MODELS

NOTE: If only one dimension is shown, dimension is the same for both 36" and 42" models.

Left Side View with Air Kit

Top View

Outside Air Kit Location (Optional)

Right Side View

Firebox Top View

Front View

Back View

Figure 2 - Firebox Dimensions (36" and 42" Models)

SuperiorFireplaces.US.com

126709-01B6

AIR FOR COMBUSTION AND VENTILATION

Unusually tight construction is deﬁ ned as

WARNING: This heater shall not be installed in a room or space unless the required volume of indoor combustion air is provided by the method described in the National

Fuel Gas Code, ANSI Z223.1/NFP A 54, the International Fuel Gas Code, or applicable local codes.

Read the following instructions to ensure proper fresh air for this and other fuel-burning appliances in your home.

Today’s homes are built more energy efﬁ cient than ever. New materials, increased insulation and new construction methods help reduce heat loss in homes. Homeowners apply weather strip and caulk around windows and doors to keep the cold air out and the warm air in. During heating months, homeowners want their homes as airtight as possible.

While it is good to make your home energy efﬁ cient, your home needs to breathe. Fresh air must enter your home. All fuel-burning appliances need fresh air for proper combustion and ventilation.

Exhaust fans, some ﬁ replaces, clothes dryers and some fuel-burning appliances draw air from the house to operate. Y ou must provide adequate fresh air for these appliances. This will ensure proper venting of vented fuel-burning appliances.

PROVIDING ADEQUA TE VENTILA TION

The following are excerpts from National Fuel Gas Code, ANSI Z223.1/NFPA 54, Air for Combustion and Ventilation.

All spaces in homes fall into one of the three following ventilation classiﬁ cations:

1. Unusually Tight Construction

2. Unconﬁ ned Space

3. Conﬁ ned Space The information on Pages 8 through 10 will help

you classify your space and provide adequate ventilation.

Unusually Tight Construction

The air that leaks around doors and windows may provide enough fresh air for combustion and ventilation. However, in buildings of unusually tight construction, you must provide additional fresh air.

126709-01B 7

SuperiorFireplaces.US.com

construction where: a. walls and ceilings exposed to the outside

atmosphere have a continuous water vapor retarder with a rating of one perm (6 x 10 openings gasketed or sealed and

b. weather stripping has been added on

openable windows and doors and

c. caulking or sealants are applied to areas

such as joints around window and door frames, between sole plates and ﬂ oors, between wall-ceiling joints, between wall panels, at penetrations for plumbing, electrical and gas lines and at other openings.

If your home meets all of the three criteria above, you must provide additional fresh air. See Ventilation Air From Outdoors, Page 10.

If your home does not meet all of the three criteria above, proceed to Determining Fresh- Air Flow For Firebox Location.

Conﬁ ned and Unconﬁ ned Space

The National Fuel Gas Code, ANSI Z223.1/ NFPA54 allows two methods for determining

whether the space in which the heater is being installed is conﬁ ned or unconﬁ ned space. The standard method deﬁ nes a conﬁ ned space as a space whose volume is less than 50 cubic feet per 1,000 Btu per hour (4.8 m gregate input rating of all appliances installed in that space and an unconﬁ ned space as a space whose volume is not less than 50 cubic feet per 1,000 Btu per hour (4.8 m gregate input rating of all appliances installed in that space. Rooms communicating directly with the space in which the appliances are installed*, through openings not furnished with doors, are considered a part of the unconﬁ ned space.

Where the air inﬁ ltration rate of a structure is known, the Known Air Inﬁ ltration Rate Method may be used. Follow The National Fuel Gas Code, ANSI Z223.1/NFPA 54 to use this method to determine if the space is conﬁ ned or unconﬁ ned.

* Adjoining rooms are communicating only if there are doorless passageways or ventilation grills between them.

-11

kg per pa-sec-m2) or less with

3

per kw) of the ag-

3

per kw) of the ag-

DETERMINING FRESH-AIR FLOW FOR HEATER LOCATION

Determining if You Have a Conﬁ ned or Unconﬁ ned Space Using the Standard Method

AIR FOR COMBUSTION AND VENTILATION

Continued

Use this work sheet to determine if you have a conﬁ ned or unconﬁ ned space.

Space: Includes the room in which you will install heater plus any adjoining rooms with doorless passageways or ventilation grills between the rooms.

1. Determine the volume of the space (length x width x height).

Length x Width x Height =__________cu. ft.

(volume of space)

Example

(width) x 8 ft. (ceiling height) = 3,168 cu. ft. (volume of space)

If additional ventilation to adjoining room

is supplied with grills or openings, add the volume of these rooms to the total volume of the space.

2. Multiply the space volume by 20 to determine the maximum Btu/Hr the space can support.

________ (volume of space) x 20 = (Maxi-

mum Btu/Hr the space can support)

Example

= 63,360 (maximum Btu/Hr space can support)

3. Add the Btu/Hr of all fuel burning appliances in the space.

Vent-free ﬁ replace _________Btu/Hr Gas water heater* _________Btu/Hr Gas furnace _________Btu/Hr Vented gas heater _________Btu/Hr Gas ﬁ replace logs _________Btu/Hr Other gas appliances* + _________ Btu/Hr Total = _________Btu/Hr * Do not include direct-vent gas appliances.

Direct-vent draws combustion air from the outdoors and vents to the outdoors.

Example: Gas water heater _________Btu/Hr Vent-free ﬁ replace + _________Btu/Hr Total = _________Btu/Hr

: Space size 22 ft. (length) x 18 ft.

: 3,168 cu. ft. (volume of space) x 20

40,000 39,000 79,000

4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/ Hr used.

_______ Btu/Hr (maximum the space can support) _______ Btu/Hr (actual amount of Btu/Hr used)

Example

79,000 Btu/Hr (actual amount of The space in the example is a conﬁ ned space

because the actual Btu/Hr used is more than the maximum Btu/Hr the space can support. You must provide additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an

adjoining room. If the extra space provides an unconﬁ ned space, remove door to adjoining room or add ventilation grills between rooms. See Ventilation Air From Inside Building.

B. Vent room directly to the outdoors. See

Ventilation Air From Outdoors, Page 9.

C. Install a lower Btu/Hr ﬁ replace, if lower Btu/

Hr size makes room unconﬁ ned.

: 63,360 Btu/Hr (maximum the

space can support) Btu/Hr used)

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconﬁ ned space. You will need no additional fresh air ventilation.

WARNING: If the area in which the heater may be operated does not meet the required volume for indoor combustion air, combustion and ventilation air shall be provided by one of the methods described in the

National Fuel Gas Code, ANSI Z223.1/NFPA 54, the International Fuel Gas Code, or applicable

local codes.

SuperiorFireplaces.US.com

126709-01B8

AIR FOR COMBUSTION AND VENTILATION

A

Continued

VENTILA TION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining unconfined space. When ventilating to an adjoining unconﬁ ned space, you must provide two permanent openings: one within 12" of the ceiling and one within 12" of the ﬂ oor on the wall connecting the two spaces (see options 1 and 2, Figure 4). Y ou can also remove door into adjoining room (see option 3, Figure 3). Follow the National Fuel Gas Code, ANSI Z223.1/ NFPA 54, Air for Combustion and Ventilation for required size of ventilation grills or ducts.

12"

Ventilation

Grills

Into Adjoining

Room,

Option 1

Or

Remove Door into Adjoining

Room, Option

3

Figure 3 - Ventilation Air from Inside

Ventilation Grills

Into Adjoining Room,

Option 2

12"

Building

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12" of the ceiling and one within 12" of the ﬂ oor . Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces. Follow the National Fuel

Gas Code, ANSI Z223.1/NFPA 54, Air for Combustion and Ventilation for required size

of ventilation grills or ducts. IMPORTANT: Do not provide openings

for inlet or outlet air into attic if attic has a thermostat-controlled power vent. Heated air entering the attic will activate the power vent.

Ventilated Attic

Ventilated

Crawl Space

To Attic

To

Crawl

Space

Outlet

ir

Inlet Air

Outlet Air

Inlet Air

Figure 4 - Ventilation Air from Outdoors

INSTALLATION

WARNING: A qualiﬁ ed ser- vice person must install ﬁ rebox. Follow all local codes.

WARNING: Never install

ﬁ rebox

• in a bedroom or bathroom*

• in a recreational vehicle

• where curtains, furniture, clothing, or other ﬂ ammable objects are less than 36" from front or 42" from top of ﬁ rebox; for side clearances see Figure 5, Page 10

• in high trafﬁ c areas

• in windy or drafty areas

* Unless installed log set is rated at 10,000 Btu/Hr or less.

CAUTION: Log heaters installed in this firebox create warm air currents. These currents move heat to wall surfaces next to ﬁ rebox. Installing ﬁ rebox next to vinyl or cloth wall coverings or operating ﬁ rebox where impuri- ties (such as, but not limited to, tobacco smoke, aromatic candles, cleaning ﬂ uids, oil or kerosene lamps, etc.) in the air exist, may discolor walls or cause odors.

126709-01B 9

SuperiorFireplaces.US.com

INSTALLATION

Continued

IMPORTANT: Vent-free gas log heaters add

moisture to the air. Although this is beneﬁ cial, installing ﬁ rebox in rooms without enough ventilation air may cause mildew to form from too much moisture. See Air for Combustion

and Ventilation, Page 7. IMPORTANT: Make sure firebox is level.

If ﬁ rebox is not level, log set will not work properly.

NOTE: Your ﬁ rebox is designed to be used in zero clearance installations. Wall or framing material can be placed against any exterior surface on rear, sides, top or bottom of ﬁ rebox, except where standoff spacers are integrally attached. If standoff spacers are attached to ﬁ rebox, these spacers can be placed directly against wall or framing materials.

Use dimensions shown for rough openings to create the easiest installation (see Built-In

Firebox Installation, Page 11).

INSTALLATION CLEARANCES

WARNING: Maintain the minimum clearances. If you can, provide greater clearances from ﬂ oor, ceiling and adjoining wall.

Carefully follow these instructions. This will ensure safe installation.

Minimum Wall and Ceiling Clearances (see Figure 5)

A. Clearances from side of ﬁ replace cabinet

to any combustible material and wall should follow diagram in Figure 5.

Example: The face of a mantel, bookshelf,

etc. is made of combustible material and protrudes 3-1/2" from wall. This combustible material must be 4" from side of ﬁ replace cabinet (see Figure 5).

B. Clearances from top of ﬁ rebox opening to

ceiling should not be less than 42".

C. When ﬁ rebox is installed on carpeting,

tile (vinyl) or other combustible material, other than wood ﬂ ooring, ﬁ rebox should be installed on a metal or wood panel extending full width and depth of enclosure.

D. Clearances from bottom of ﬁ rebox to ﬂ oor

is 0".

These ﬁ reboxes can be installed as freestand- ing units against a wall with approved, optional cabinet mantels (see Accessories, Page 15) or as a built-in unit. Clearances are the same for either installation method.

CAUTION: Do not install ﬁ re-

box directly on carpet or vinyl.

Example

*

*Minimum 16" from Side Wall

Figure 5 - Minimum Clearance for

Combustible to Wall

Mantel Clearances for Built-In Installation

If placing custom mantel above built-in ﬁ rebox, you must meet minimum allowable clearance between mantel shelf and top of ﬁ rebox open- ing shown in Figure 6, Page 11. These are minimum allowable mantel clearances for a safe installation. Use larger clearances wherever possible to minimize heating of objects and materials placed on mantel.

CAUTION: Do not allow ventfree gas log heater to touch or extend beyond ﬁ replace screen.

NOTICE: Surface temperatures of adjacent walls and mantels become hot during operation. Walls and mantels above ﬁ rebox may become hot to the touch. If installed properly, these temperatures meet the requirement of the national product standard. Follow all minimum clearances shown in this manual.

SuperiorFireplaces.US.com

126709-01B10

INSTALLATION

Depth

(Minimum)

Width

(Inside to Inside)

Height

37"

45°

42

1

/2"

52"

74"

TOP VIEW

FOR 36" MODELS

Continued

NOTICE: If your installation does not meet the minimum clearances shown, you must do one of the following:

• raise the mantel to an acceptable height

• remove the mantel

BUILT-IN FIREBOX INSTALLATION

Built-in installation of this ﬁ rebox involves installing ﬁ rebox into a framed-in enclosure. This makes the front of ﬁ rebox ﬂ ush with wall. Optional brass trim accessories are available (see Accessories, Page 15). Brass trim will extend past sides of ﬁ rebox approximately 1/2". This will cover rough edges of wall opening. If installing a mantel above ﬁ rebox, you must follow clearances shown in Figure 6. Follow these instructions to install ﬁ rebox in this manner.

1. Frame in rough opening. Firebox framing should be constructed of 2 x 4 lumber or heavier. Use dimensions in table and rough opening layout in Figure 7a. Adjust framing so that ﬁ rebox is ﬂ ush with ﬁ n- ished wall surface. If installing in a corner, use dimensions in Figures 7b, 7c and 7d for rough opening.

Wall board or facing material (above firebox) may be of combustible material, including decorative mantel ornaments or other similar projections off of the facing material.

Framing Material

Firebox

Mantel Shelf Note: Any portion of the mantel shelf must NOT extend beyond this profile.

12"

3

/

4

"

6

1

/

2

"

Noncombustible Material May Project Off this Surface above the Firebox Hood

12" 16" 20"

2. Install gas piping to ﬁ rebox location. See In- stalling Gas Line, Page 12 and Connecting to Gas Supply in log set owner’s manual.

3. Carefully set ﬁ rebox in front of rough open- ing with back of ﬁ rebox inside wall open- ing. IMPORTANT: If installing a perimeter trim kit, see instructions included with trim accessory . You must install shoulder screws from trim kit now.

Rough Opening Dimensions for

Built-in Installation

Model

Front Width

(Inside to Inside) Height

Depth (Min.)

32" 35 7/8" 36 3/4" 16 1/4"

1

36" 42 42" 49

/2" 40 1/2" 20 3/4"

5

/8" 44 1/2" 22 5/8"

Figure 7a

FOR 32"

35

60"

7

/8"

MODELS

Figure 7b

45°

30"

42

7

"

16

/

TOP VIEW

Figure 7c

Wire-mesh Screen

These minimum clearances replace any other recommended clearances supplied with your ANSI Z21.11.2 approved gas logs.

Figure 6 - Minimum Mantel Clearances

126709-01B 11

for Built-In Installation

Supplied Firebox Hood Must Be Used at All Times

Note: All vertical measurements are from top of fireplace opening to bottom of mantel shelf.

43"

Figure 7 - Rough Opening for Installing

SuperiorFireplaces.US.com

61"

5

49

/8"

86"

TOP VIEW

in Wall

FOR 42" MODELS

Figure 7d

45°

INSTALLATION

Continued

4. Carefully insert ﬁ rebox into rough opening.

5. Attach ﬁ rebox to wall studs using nails or wood screws through holes in nailing ﬂ ange (see Figure 8).

6. If using an optional perimeter trim kit, install trim after ﬁ nal ﬁ nishing and/or paint- ing of wall. See instructions included with trim accessory for attaching trim.

7. Install and properly test gas log heater. Follow installation instructions included with vent-free gas log heater that is being installed.

IMPORTANT: When ﬁ nishing your ﬁ rebox, combustible materials such as wall board, gypsum board, sheet rock, drywall, plywood, etc. may be butted up next to sides and top of ﬁ rebox. Combustible materials should never overlap ﬁ rebox front facing.

Nails or Wood Screws

W ARNING: Do not allow any combustible materials to overlap ﬁ rebox front facing.

IMPORTANT: Noncombustible materials such as brick, tile, etc. may overlap front facing, but should never cover any necessary openings like louvered slots.

WARNING: Do not allow noncombustible materials to cover any necessary openings like louvered slots.

WARNING: Use only noncombustible mortar or adhesives when overlapping the front facing with noncombustible facing material.

Nails or Wood Screws

Nailing Flanges

Indoor Firebox

INSTALLING FIREBOX USING OPTIONAL ACCESSORY MANTELS

WARNING: A qualiﬁ ed ser- vice person must install ﬁ rebox. Follow all local codes.

This ﬁ rebox may be installed using a cabinet mantel accessory against a wall in your home. Firebox and cabinet mantel can be installed directly on ﬂ oor. A trim kit is included with mantel accessories. Follow instructions with mantel for installation.

Nailing Flanges

Indoor/Outdoor Firebox

Figure 8 - Attaching Firebox to Wall Studs

SuperiorFireplaces.US.com

126709-01B12

INSTALLATION

Continued

WARNING: Do not allow noncombustible materials to cover any necessary openings.

WARNING: Do not ﬁ ll the spaces around the ﬁ rebox with insulation or other materials.

Equipment Shutoff Valves (Install One)

W ARNING: Framing may be placed or rest against ﬁ replace spacer, however; framing must never be

notched.

WARNING: Do not alter, cut or modify ﬁ replace spacers.

INSTALLING GAS LINE

NOTICE: A qualiﬁ ed service per- son must connect heater to gas supply. Follow all local codes.

IMPORTANT: See Connecting to Gas Supply in your log set owner’s manual for details on gas hookup.

Y ou may run gas line from either side or back of ﬁ rebox (see Figure 9, Page 13). Decide which side you want to run gas line from.

NOTE: This is one option for installing shutoff valve. Check local codes for equipment shutoff valve location requirements.

Locate recessed knockout in one ﬁ rebrick liner (see Figures 9 and 10). Firmly tap center of knockout with a chisel until it is released. Carefully chisel rough edges of hole you have made to smooth edges. This hole will line up with hole in outer casing.

Knockout Locations (Knock Out One Hole)

Figure 9 - Installing Gas Line and

Equipment Shutoff Valve (Model May

Firebrick Side Wall

Knockout

Figure 10 - Location of Knockout for

Gas Line Hole

Vary From Illustration)

Remove this Area

Chisel

Gas Line

Side View

CAUTION: Do not use excessive force to remove the knockout. Too much force may damage the ﬁ rebrick concrete insert.

126709-01B 13

SuperiorFireplaces.US.com

INSTALLATION

Continued

OPTIONAL OUTSIDE AIR KIT (MODEL AK4/AK4F)

Installation of outside air kit should be performed during rough framing of ﬁ replace due to the nature of it's location. Outside combustion air is accessed through a vented crawl space (AK4F) or through a sidewall (AK4). See Figure 11.

CAUTION: Combustion air inlet ducts shall not terminate in attic space.

Secure to Collars with Metal Tape, Screws or Straps (Min. of 1/4" x 20" in size)

Air Inlet Location Must Allow For Bushes or Snow

Air Inlet

Vented Crawl Space (Check Local Codes Before Installing in a Vented Crawl Space)

Figure 11 - Outside Air Kit

Hood

Eyebrow

Vent Hood Required for Wall Installation

Hood

Figure 12 - Hood Placement

(Model May Vary From Illustration)

2. For Indoor/outdoor models, loosen screws along the ﬁ replace top face. Remove two screws along ﬁ replace face side. Slide hood underneath screws on top and tighten screws. Replace screws on side of ﬁ replace face side securing hood to the face (see Figure 13).

3. Insert each screen rod through all rings located at top of screen.

4. Insert ﬁ rst rod into rear hole in left side of ﬁ rebox. Fasten rod to rear hole near center of ﬁ rebox using #10 x 3/8" Phillips screw provided (see Figure 14).

5. Insert other rod into front hole on right side of ﬁ rebox and fasten using remaining Phillips screw.

Top View of Rod Layout

Rear Hole

Identiﬁ cation Label Location

Remove/Replace Side Screws

Figure 13 - Hood Placement

(Model May Vary From Illustration)

Loosen Top Screws

INSTALLING FIREPLACE HOOD AND SCREEN

1. For Indoor models, attach hood and front panel assembly by snapping panel assembly into ﬁ replace opening (see Figure 12).

SuperiorFireplaces.US.com

Front Hole

Rod

Ring

Screen

Figure 14 - Installing Fireplace Screen

(Model May Vary From Illustration)

Screw

126709-01B14

REPLACEMENT PARTS

See Pages 17-20 for a complete replacement parts list. Use only parts supplied from the manufacturer.

Normally, all parts should be ordered through your IHP distributor or dealer. Parts will be shipped at prevailing prices at time of order.

When ordering repair parts, always give the following information:

SERVICE HINTS

When Gas Pressure Is Too Low

• pilot will not stay lit

• burners will have delayed ignition

• appliance will not produce speciﬁ ed heat

• propane/LP gas supply may be low You may feel your gas pressure is too low. If

so, contact your local propane/LP or natural gas supplier.

1. The model number of the appliance.

2. The serial number of the appliance.

3. The part number.

4. The description of the part.

5. The quantity required.

6. The installation date of the appliance.

If you encounter any problems or have any questions concerning the installation or application of this appliance, please contact your dealer.

TECHNICAL SERVICE

You may have further questions about installation, operation, or troubleshooting. Please contact your IHP dealer for any questions or concerns. When contacting your dealer please have your model and serial numbers of your appliance ready. You can also visit our web site at SuperiorFireplaces.US.com.

ACCESSORIES

Purchase these appliance accessories from your local dealer. If they can not supply these accessories, contact IHP at SuperiorFireplaces.US.com for referral information. You can also write to the address listed on the back page of this manual.

Only kits supplied by IHP shall be used in the installation of this appliance. Use of non-approved accessory/part kit(s) can result in poor performance and safety hazards.

OPTIONAL OUTSIDE AIR KIT FOR SIDEWALL INSTALLATION

Cat. No. F1091, Model AK4

4" Air Kit with Collar, Hood & 3' Flex

Cat. No. F1092, Model AK4X

4" Air Kit, Collar & Hood Only

Optional kit provides additional air to reduce build-up of condensation that occurs in today's tightly constructed homes.

REFRACTORY STAIN KITS

Use the Refractory Stain Kits to give white refractory panels a new look.

Kit includes foam roller, roller handle, paint tray, and one can of stain. Available stain colors are Creamer (ivory), Rust (terra cotta), and Cappuccino (rosy taupe).

Creamer H8176 BSK-CR Rust H8177 BSK-RT Cappuccino H8178 BSK-CP

Creamer Rust Cappuccino

126709-01B 15

SuperiorFireplaces.US.com

ACCESSORIES

Continued

Notice: All accessories may not be available for all ﬁ replace models.

HOODS

Cat. No. F1048, Model H36B

36" VF Fireplace Hood - Brushed Brass

Cat. No. F1049, Model H36P

36" VF Fireplace Hood - Platinum

Cat. No. F1050, Model H42B

42" VF Fireplace Hood - Brushed Brass

Cat. No. F1051, Model H42P

42" VF Fireplace Hood - Platinum

MANTELS

32" Mantels

Cat. No. J3495, Model W32TU

32" Wall Mantel, Unﬁ nished, Traditional

Cat. No. J3494, Model W32TO

32" Wall Mantel, Oak Stain, Traditional

Cat. No. J0408, Model C32TU

32" Corner Mantel, Unﬁ nished, Traditional

Cat. No. J0407 F, Model C32TO

32" Corner Mantel, Oak Stain, Traditional

Cat. No. J3490, Model W32CO

32" Wall Mantel, Oak Stain, Classic

Cat. No. F1811, Model

32" Corner Mantel, Oak Stain, Classic

Cat. No. F1812, Model W32DO

32" Wall Mantel, Oak Stain, Dentil

Cat. No. F1813, Model W32GO

32" Wall Mantel, Oak Stain, Georgian

Cat. No. F1149, Model C32GO

32" Corner Mantel, Oak Stain, Georgian

C32CO

PERIMETER TRIM

Cat. No. F1039, Model PT32

32" Black

Cat. No. F1040, Model PT32B

32" Brushed Brass

Cat. No. F1041, Model PT32P

32" Platinum

Cat. No. F1042, Model PT36

36" Black

Cat. No. F1043, Model PT36B

36" Brushed Brass

Cat. No. F1044, Model PT36P

36" Platinum

Cat. No. F1045, Model PT42

42" Black

Cat. No. F1046, Model PT42B

42" Brushed Brass

Cat. No. F1047, Model PT42P

42" Platinum

VENT FREE GAS LOGS

Please visit SuperiorFireplaces.US.com for speciﬁ c models, sizing, speciﬁ cations and dealers in your area.

36" Mantels

Cat. No. J3496, Model W36TO

36" Wall Mantel, Oak Stain, Traditional

NOTE: No 42" mantels offered at this time.

SuperiorFireplaces.US.com

126709-01B16

PARTS

32", 36", AND 42" MODELS

15

14

13

11

10

16

Cat. No. Model Interior

F0286 VRT4032WS White Stack F0287 VRT4032WH White Herringbone

F0288 VRT4036WS White Stack

F0289 VRT4036WH White Herringbone

F0290 VRT4042WS White Stack

17

12

8

19

21

18

9

19

20

18

22

7

20/20a

19

4

3

6

5

2

1

126709-01B 17

SuperiorFireplaces.US.com

PARTS

This list contains replaceable parts used in your ﬁ rebox. When ordering parts, follow the instructions listed under Replacement Parts on Page 15 of this manual.

KEY NO. PART NO. DESCRIPTION QTY.

32"

36"

42"

1 J5130 Screen 36" • 2

J5131 Screen 32" • 2 J5132 Screen 42" • 2 J7449 Screen 36" Stainless • 2 F3144 Screen 32" Stainless • 2 F3145 Screen 42" Stainless • 2

2 K2001 Screen Rod 32" • 2

J3975 Screen Rod 36" • 2 J4084 Screen Rod 42" • 2 F3147 Screen Rod 32" Stainless • 2 F3148 Screen Rod 36" Stainless • 2

F3149 Screen Rod 42" Stainless • 2 3 J4956 Push-On Nut • • • 2 4 J5210 Hood Assembly Panel • 1

J521 1 Hood Assembly Panel • 1

J5212 Hood Assembly Panel • 1

RP108414-05 Stainless Hood 32" • 1

J4091 Stainless Hood 36" • 1

J7441 Stainless Hood 42" • 1 5 ** Face Weldment • • • 1 6 ** Firebox Bottom • • • 1 7 ** Firebox Surround • • • 1 8 J5185 Refractory Retainer • • • 2 9 J5186 Rear Refractory Retainer • • • 1

10 RP108413-01 Firebox Top Shield • • • 1 1 1 ** Firebox Top • • • 1 12 ** Starter Pipe Collar • • • 1 13 ** Insulation Pan • • • 1 14 ** Fireplace Top Insulation • • • 1 15 ** Fireplace Top • • • 1 16 J6918 Top Spacer • • • 4 17 ** Fireplace Surround • • • 1 18 J4223 Gas Conduit Left and Right Assembly • 2 19 J6934 Gas Knock-Out Cover • • • 3-5 20 J4011 Gas Conduit • • • 2

20a J6951 Gas Conduit • • 2

J6952 Gas Conduit • • 2

21 J6900 Cover Plate • • • 1 22 **

Side Damper Weldment

••• 1

** Not a ﬁ eld replaceable part.

SuperiorFireplaces.US.com

126709-01B18

PARTS

32", 36", AND 42" MODELS

2

1

2

3

4

IMPORTANT: Installation of brick panels should be done after the fireplace is placed in a permanent location.

1

5

4

KEY

NO. PART NO. DESCRIPTION QTY.

1

F3248 White Stack Refractory Set, 32" F3250 White Stack Refractory Set, 36" F3258 White Stack Refractory Set, 42" F3249 White Herringbone Refractory Set, 32" F3251 White Herringbone Refractory Set, 36" F3257 White Herringbone Refractory Set, 42"

2 --- Left Refractory Stacked White, 32" • 1

--- Left Refractory Herringbone White, 32" • 1

3 --- Rear Refractory Stacked White, 32" • 1

--- Rear Refractory Herringbone White, 32" • 1

4 --- Right Refractory Stacked White, 32" • 1

--- Right Refractory Herringbone White, 32" • 1 5 --- Bottom Refractory White, 32" • • 1 2 --- Left Refractory Stacked White, 36" • 1

--- Left Refractory Herringbone White, 36" • 1 3 --- Rear Refractory Stacked White, 36" • 1

--- Rear Refractory Herringbone White, 36" • 1 4 --- Right Refractory Stacked White, 36" • 1

--- Right Refractory Herringbone White, 36" • 1 5 --- Bottom Refractory White, 36" • • 1 2 --- Left Refractory Stacked White, 42" • 1

--- Left Refractory Herringbone White, 42" • 1 3 --- Rear Refractory Stacked White, 42" • 1

--- Rear Refractory Herringbone White, 42" • 1 4 --- Right Refractory Stacked White, 42" • 1

--- Right Refractory Herringbone White, 42" • 1 5 --- Bottom Refractory White, 42" • • 1

LIFTING HAZARD

SINGLE -PERSON LIFT COULD

CAUSE INJURY.

USE ASSISTANCE WHEN MOVING

OR LIFTING.

VRT4036WS

VRT4036WH

VRT4042WS

VRT4032WS

VRT4032WH

VRT4042WH

•1

3

WARNING

126709-01B 19

SuperiorFireplaces.US.com

_

NOTES

____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________

SuperiorFireplaces.US.com

126709-01B20

_

NOTES

____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________

126709-01B 21

SuperiorFireplaces.US.com

_

NOTES

____________________________________________________

____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________ ____________________________________________________

SuperiorFireplaces.US.com

126709-01B22

Innovative Hearth Products

®

Superior

Brand Gas Fireplaces, Stoves and Inserts

20 Year Limited Warranty

THE WARRANTY

Innovative Hearth Products ("IHP") 20 Year Limited Warranty warrants your Superior® Brand gas ﬁ replace, Stove or Insert ("Product") to be free from defects in materials and workmanship at the time of manufacture. The product body, ﬁ rebox and barrier carry the 20 Year Limited Warranty. Ceramic glass carries the 20 Year Limited Warranty against thermal breakage only. After installation, if covered components manufactured by IHP are found to be defective in materials or workmanship during the 20 Year Limited Warranty period and while the Product remains at the site of the original installation, IHP will, at its option, repair or replace the covered components. If repair or replacement is not commercially practical, IHP will, at its option, refund the purchase price or wholesale price of the IHP product, whichever is applicable. IHP will also pay IHP prevailing labor rates, as determined in its sole discretion, incurred in repairing or replacing such components for up to ﬁ ve years. THERE ARE EXCLUSIONS AND LIMITATIONS to this 20 Year Limited Warranty as described herein.

COVERAGE COMMENCEMENT DATE

Warranty coverage begins on the date of purchase. In the case of new home construction, warranty coverage begins on the date of ﬁ rst occupancy of the dwelling or six months after the sale of the Product by an independent IHP dealer/distributor, whichever occurs earlier. The warranty shall commence no later than 24 months following the date of product shipment from IHP, regardless of the installation or occupancy date.

EXCLUSIONS AND LIMITATIONS

This 20 Year Limited Warranty applies only if the Product is installed in the United States or Canada and only if operated and maintained in accordance with the printed instructions accompanying the Product and in compliance with all applicable installation and building codes and good trade practices.

This warranty is non-transferable and extends to the original owner only. The Product must be purchased through a listed supplier of IHP and proof of purchase must be provided. The product body, ﬁ rebox and barrier carry the 20 Year Limited Warranty from the date of installation. Vent components, trim components and paint are excluded from this 20 Year Limited Warranty. The following do not carry the 20 Year Limited Warranty but are warranted as follows:

Burner – Repair or replacement for one year from the date of installation Gas components – Repair or replacement for one year from the date of installation Gaskets – Repair or replacement for one year from the date of installation Logs – Replacement for one year from the date of installation against thermal breakage only Optional blowers & remote controls – Repair or replacement for one year from the date of installation Optional glass doors – Repair or replacement for 90 days from the date of installation Tempered glass - Replacement for one year from the date of installation Labor coverage – Prevailing IHP labor rates apply for the warranty period of the component

Parts not otherwise listed carry a 90 day warranty from the date of installation.

Whenever practicable, IHP will provide replacement parts, if available, for a period of 10 years from the last date of manufacture of the Product.

IHP will not be responsible for: (a) damages caused by normal wear and tear, accident, riot, ﬁ re, ﬂ ood or acts of God; (b) damages caused by abuse, negligence, misuse, or unauthorized alteration or repair of the Product affecting its stability or performance (The Product must be subjected to normal use. The Product is designed to burn either natural or propane gas only. Burning conventional fuels such as wood, coal or any other solid fuel will cause damage to the Product, will produce excessive temperatures and could result in a ﬁ re hazard.); (c) damages caused by failing to provide proper maintenance and service in accordance with the instructions provided with the Product; (d) damages, repairs or inefﬁ ciency resulting from faulty installation or application of the Product.

IHP is not responsible for inadequate ﬁ replace system draft caused by air conditioning and heating systems, mechanical ventilation systems, or general construction conditions which may generate negative pressure in the room in which the appliance is installed. Additionally IHP assumes no responsibility for drafting conditions caused by venting conﬁ gurations, adjoining trees or buildings, adverse wind conditions or unusual environmental factors and conditions that affect the operation of the unit.

This 20 Year Limited Warranty covers only parts and labor as provided herein. In no case shall IHP be responsible for materials, components or construction, which are not manufactured or supplied by IHP or for the labor necessary to install, repair or remove such materials, components or construction. Additional utility bills incurred due to any malfunction or defect in equipment are not covered by this warranty. All replacement or repair components will be shipped F.O.B. from the nearest stocking IHP factory.

LIMITATION ON LIABILITY

It is expressly agreed and understood that IHP’s sole obligation and the purchaser’s exclusive remedy under this warranty, under any other warranty, expressed or implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as speciﬁ ed herein.

In no event shall IHP be liable for any incidental or consequential damages caused by defects in the Product, whether such damage occurs or is discovered before or after repair or replacement, and whether such damage is caused by IHP’s negligence. IHP has not made and does not make any representation or warranty of ﬁ tness for a particular use or purpose, and there is no implied condition of ﬁ tness for a particular use or purpose.

IHP makes no expressed warranties except as stated in this 20 Year Limited Warranty. The duration of any implied warranty is limited to the duration of this expressed warranty.

No one is authorized to change this 20 Year Limited Warranty or to create for IHP any other obligation or liability in connection with the Product. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. The provisions of this 20 Year Limited Warranty are in addition to and not a modiﬁ cation of or subtraction from any statutory warranties and other rights and remedies provided by law.

INVESTIGATION OF CLAIMS AGAINST WARRANTY

IHP reserves the right to investigate any and all claims against this 20 Year Limited Warranty and to decide, in its sole discretion, upon the method of settlement.

To receive the beneﬁ ts and advantages described in this 20 Year Limited Warranty, the appliance must be installed and repaired by a licensed contractor approved by IHP.

Contact IHP at the address provided herein to obtain a listing of approved dealers/distributors. IHP shall in no event be responsible for any warranty work done by a

contractor that is not approved without ﬁ rst obtaining IHP's prior written consent.

HOW TO REGISTER A CLAIM AGAINST WARRANTY

In order for any claim under this warranty to be valid, you must contact the IHP dealer/distributor from which you purchased the product. If you cannot locate the dealer/ distributor, then you must notify IHP in writing. IHP must be notiﬁ ed of the claimed defect in writing within 90 days of the date of failure. Notices should be directed to the IHP Warranty Department at 1508 Elm Hill Pike, Suite 108; Nashville, TN 37210 or visit our website at WWW.SUPERIORFIREPLACES.US.COM.

P/N 900223-00, Rev. B 10/2016

Innovative Hearth Products 1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210

SuperiorFireplaces.US.com

Record the following important information about your appliance:

Appliance model number

Appliance serial number

Date appliance was Installed

Type of gas appliance uses

Dealer name

IHP reserves the right to make changes at any time, without notice, in design, materials, speciﬁ cations, prices and also to discontinue colors, styles and products. Consult your local distributor for ﬁ replace code information.

24

P/N 126709-01 Rev. B 01/2017

P126709-01

1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210