Superior UVF-36 User Manual

HEARTH PRODUCTS

KITS AND ACCESSORIES

750,209M REV. NC 03/2006

INSTALLATION INSTRUCTIONS FOR DECORATIVE ARCH SCREEN DOOR KITS

FOR USE WITH UVF-36, UVFRC-3628, UVFRC-3628-H

UVFRC-4228 & UVFRC-4228-H UNIVERSAL VENTFREE FIREBOXES

* DECORATIVE SCREEN DOOR PANEL KITS

CAT. NO. MODEL WHERE USED

H1959 ASD3624-TI UVF-36

H1960 ASD3628-TI UVFRC-3628 & UVFRC-3628-H

H1961 ASD4228-TI UVFRC-4228 & UVFRC-4228-H

Table 1

* A canopy hood is required when installing these Decorative Arch Screen Door Kits (the canopy is sold separately for A canopy is a standard part for model UVF-36).

QUANTITY DESCRIPTION

1 ea. Screen Door, Left

1 ea. Screen Door, Right

1 ea. Doorframe

1 ea. Instruction Sheet

Table 2

UVFRC-3628, UVFRC-3628-H, UVFRC-4228 & UVFRC-4228-H

KIT CONTENTS

DECORATIVE ARCH SCREEN DOOR KIT

INSTALLATION INSTRUCTIONS:

1. All Models - Using a 5/16” socket or nutdriver remove screen and rod assemblies as shown in Figure 2. Reinstall the Screen Rod Screws! The Screen

and Rod Assemblies must NOT be installed when the screen door kit is installed! You may wish to retain the screen and rod assemblies in case the screen door kit is ever removed in the future (read Important Note in Figure 2).

Remove Screens & Rods.

A) Remove screws (see dotted lines). Pull out rods from locating holes on side of ﬁ rebox opening.

B) IMPORTANT: Reinstall screen rod screws into the existing holes where removed.

IMPORTANT NOTE: If this optional

screen door kit is ever removed, the rod and screens MUST be reinstalled for safe operation of the appliance.

Figure 2

ARCH SCREEN DOOR KIT

Left Screen Door

Doorframe

Right Screen Door

Figure 1

TOOLS REQUIRED

Phillips Screwdriver 5/16” Socket or Nutdriver

GENERAL INFORMATION

This decorative screen door ﬁ ts on the face of the appliance. If you encounter any problems, need clariﬁ cation of these instructions or are not qualiﬁ ed to

properly install this kit, contact your local distributor or dealer.

Read and understand all instructions and warnings in this document before beginning the installation.

CAUTION

INSTALL ONLY WHEN THE APPLIANCE IS OFF AND COLD!

2. All Models - Remove and save the (2) two upper side frame screws as shown in Figure 3 (on both sides of ﬁ rebox). Loosen the bottom side frame screws (do not remove). See Figure 3.

A) Side Frame Screws

Using a phillips screwdriver remove the side frame screw indicated here. Loosen the lower side frame screws but DO NOT remove them.

B) Set aside the screws that were removed for later use.

Do NOT remove this screw

Remove this screw

Loosen this screw, but do NOT remove it.

Firebox

Figure 3

3. Models: UVFRC-3628, UVFRC-3628-H, UVFRC-4228 & UVFRC-4228-H Only - Install Canopy (see Figure 4 and follow installation instruction in

the Installation And Operating Instructions Manual).

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Install Canopy - Models: UVFRC3628, UVFRC-3628-H, UVFRC-4228 & UVFRC-4228-H Only

Canopy

Figure 4

CAUTION

ALL MODELS MUST HAVE A CANOPY INSTALLED WHEN THIS SCREEN DOOR KIT IS INSTALLED!

4. All Models - Install doorframe assembly (provided) per instructions in

Figure 5, 6a & 6b.

Hook the bottom doorframe locating brackets over the (2) two bottom side frame screws (which were loosened in Step 3) as shown below.

Use center canopy screw (see Figure 4) to secure center top bracket to ﬁ rebox ceiling.

Position the top and bottom doorframe brackets as shown. Brackets should be positioned behind the cabinet top and bottom ﬂ anges of ﬁ rebox opening.

Top Doorframe Bracket

Doorframe

CENTER TOP & BOTTOM DOORFRAME BRACKETS

Bottom Doorframe Bracket

Figure 6b

6. All Models - Install the screen doors by aligning hinge pins on the doors with the hinge holes on the doorframe and slide down (see Figure 7). Ensure the hinge pins are fully seated onto the shoulders of the hinge holes.

Doorframe

The (4) four locating brackets on doorframe hook over side frame screws shown in Figure 3

Figure 5

Secure Doorframe to Appliance and Tighten Screws

A) Rotate the top of the doorframe ﬂ ush

with ﬁ rebox face then secure in place by installing the (2) two screws which were removed in Step 3 through the doorframe brackets into the existing holes in side frames.

B) Tighten the (2) two loose screws though the bottom locating brackets (shown in

Figure 5).

C) Adjust the center top and bottom doorframe brackets as shown in Figure 6b.

Figure 6a

Doorframe

Bottom Locating Bracket on Doorframe locates over the side frame screws which were loosened

Firebox

Figure 7 - Install Screen Doors

7. Close Doors. Installation is complete.

COMPLETED INSTALLATION

Firebox

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 8

Left Screen Door

Canopy

Screen Door

Doorframe

Hinge Pin

LHP reserves the right to make changes at any time, without notice, in design, materials, speciﬁ cations, prices and the discontinuance of colors, styles and products. Consult your local distributor for ﬁ replace code information.

P/N 750,209M REV. NC 03/2006

LHP 1110 West Taft Avenue • Orange, CA 92865