SunX EX19A, EX11APN, EX19B, EX11BPN, EX13APN User guide

...

INSTRUCTION MANUAL

Photoelectric Sensor

Ultra-slim Type

EX-10 Series

SPECIFICATIONS

Type

Front sensing Side sensing Front sensing Front sensing Front sensingSide sensing

Model No.

Item

Sensing range

Min. sensing object

Hysteresis

Repeatability (perpendicular to sensing axis)

Supply voltage Current consumption

Output

Short-circuit protection

Stability indicator

Emitting element

Accessories

Notes: 1) Model Nos. having the suffix '-PN' are PNP output type.

MOUNTING

In case of mounting on tapped holes (Unit: mm)

●

Light-ON

(Note 1)

Dark-ON

Further, model Nos. having suffix '-R' are inflection resistant cable type. (NPN output type only) The model No. with suffix 'P' shown on the label affixed to the thru-beam type sensor is the emitter, 'D' shown on the label is the receiver. Thru-beam type sensor emitter: EX-□P, Thru-beam type sensor receiver: EX-□D

EX-11A(-PN / -R) EX-11B(-PN / -R)

φ1mm opaque object

Setting distance between emitter and receiver: 150mm

<EX-□A(-R), EX-□B(-R)>

NPN open-collector transistor

・Maximum sink current: 50mA ・

Applied voltage: 30V DC or less (between output and 0V)

・Residual voltage: 1V or less (at 50mA sink current)

Side sensing Front sensing

Sensing direction

Attached screw

[M2 (length 10)]

M2×0.4 holes tapped 6 deep

・ The tightening torque should be 0.2N・m or less.

EX-11EA(-PN / -R) EX-11EB(-PN / -R)

150mm

Emitter: 10mA or less, Receiver: 15mA or less 20mA or less

0.4V or less (at 16mA sink current)

Red LED (lights up when the output is ON), located on the receiver for the thru-beam type sensorOperation indicator

Green LED (lights up under stable light received condition or stable dark condition), located on the receiver for the thru-beam type sensor

-25 to +55℃ (Note 3) (No dew condensation or icing allowed), Storage: -30 to +70℃Ambient temperature

0.1mm2 3-core (thru-beam type emitter: 2-core) cabtyre cable, 2m long (Note 4)Cable

Sensing direction

Attached screw

[M2 (length 8)]

M2×0.4 holes tapped 7 deep

EX-13A(-PN / -R) EX-19A(-PN / -R) EX-14A(-PN / -R) EX-13B(-PN / -R) EX-19B(-PN / -R) EX-14B(-PN / -R)

12 to 24V DC±10% Ripple P-P 10% or less

35 to 85% RH, Storage: 35 to 85% RHAmbient humidity

Enclosure: Polyethylene terephthalate, Lens: PolyalylateMaterial

Emitter, receiver: 20g approx. each 20g approx.Weight

Mounting screws: 2 sets

Thank you very much for using SUNX products. Please read this Instruction Manual carefully and thoroughly for the correct and optimum use of this product. Kindly keep this manual in a convenient place for quick reference.

WARNING

●●Never use this product as a sensing device for personnel protection.

In case of using sensing devices for personnel protection, use products which meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each region or country.

Thru-beam

EX-13EA(-PN / -R) EX-13EB(-PN / -R)

500mm

φ2mm opaque object

Settin g distance between emitter and receiver: 500mm

−

<EX-□A-PN, EX-□B-PN>

PNP open-collector transistor

・Maximum source current: 50mA ・

Applied voltage: 30V DC or less (between output and +V)

・Residual voltage: 1V or less (at 50mA source current)

Incorporated

0.5ms or lessResponse time

IP67 (IEC)Protection

Red LED (modulated)

Notes: 2)

The sensing range of the convergent reflective type sensor is specifie d fo r wh ite non-glossy paper (50×50m m) a s th e object.

-10 to +55℃ for the inflection resistant cable type.

The inflection resistant type has a 0.1mm2 3-core (thru-beam type emitter: 2-core) inflection resistant cabtyre cable, 2m long.

In case of using attached screws and nuts (Unit: mm)

●

Side sensing Front sensing

Thickness of mounting plate 2 or less

Sensing

direction Attached screw [M2 (length 10)]

Flat washers

φ2mm opaque object

Setting distance between emitter and receiver: 1m

0.4V or less (at 16mA source current)

Nuts

Spring washers

・ The tightening torque should be 0.2N・m or less.

Convergent reflective

2 to 25mm (Note 2) (Conv. point: 10mm)

φ0.1mm copper wire (Setting distance: 10mm)

15% or less of operation distance

0.1mm or less0.05mm or less

Mounting screws: 1 set

Sensing direction

Attached screw

[M2 (length 8)]

Thickness of mounting plate

2.5 or less

CAUTIONS

●

This product has been developed / produced for industrial use only.

●

For the convergent reflective type EX-14□, if there is a reflective object (e.g., a conveyor, etc.) in the background of the sensing object, since it may affect the sensing, use by keeping enough distance from the reflective object.

●

The thin cable (0.1mm2) is used for this product. Thus, take care that if the cable is pulled with excessive force, it may cause cable break.

●

Make sure that the power supply is off while wiring.

●

Take care that wrong wiring will damage the sensor.

●

Verify that the supply voltage variation is within the rating.

●

If power is supplied from a commercial switching regulator, ensure that the frame ground (F.G.) terminal of the power supply is connected to an actual ground.

●

In case noise generating equipment (switching regulator, inverter motor, etc.) is used in the vicinity of this product, connect the frame ground (F.G.) terminal of the equipment to an actual ground.

●

Do not run the wires together with high-voltage lines or power lines or put them in the same raceway. This can cause malfunction due to induction.

●

Extension up to total 50m, is possible with 0.3mm2, or more, cable for both, emitter and receiver. However, in order to reduce noise, make the wiring as short as possible.

●

Do not use during the initial transient time (50ms) after the power supply is switched on.

●

Take care that the sensor is not directly exposed to fluorescent lamp from a rapid-starter lamp, a high frequency lighting device or sunlight etc., as it may affect the sensing performance.

●

This sensor is suitable for indoor use only.

●

Avoid dust, dirt, and steam. Do not use it in places having excessive vapor, dust, etc., or where it may come in contact with corrosive gas.

●

Take care that the sensor does not come in contact with water, oil, grease, organic solvents, such as, thinner etc., or strong acid, and alkaline.

●

Make sure that stress by forcible bend or pulling is not applied directly to the sensor cable joint.

●

Since the cable end is not waterproof, do not use the sensor in the application where water may seep in from the cable end.

OPTIONAL SENSOR MOUNTING BRACKET

●●When mounting the sensor with the optional sensor

mounting bracket, use the attached M2 screws and the tightening torque should be 0.2N

・m or less.

Six types of optional sensor mounting brackets are available.

Model No. Description

MS-EX10-1

MS-EX10-2

MS-EX10-3

MS-EX10-11

MS-EX10-12

MS-EX10-13

Mounting bracket for front sensing type only Two M2 (length 4mm) pan head screws are attached.

Mounting bracket for side sensing type only Two M2 (length 8mm) pan head screws are attached.

L-shaped mounting bracket Two M2 (length 4mm) pan head screws, and two M2 (length 8mm) pan head screws are attached.

Mounting bracket for front sensing type only Two M2 (lengt h 4mm) pan head screws (stainless steel) are attached.

Mounting bracket for side sensing type only Two M2 (length 8m m) pan head screws (stainless steel) are attached.

L-shaped mounting bracket Two M2 (length 4mm) pan head screws (stainless steel ), and two M2 (length 8mm) pan head screws (stainless steel) are attached.

OPTIONAL SLIT MASK

Material

Cold rol led carbon steel (SPCC)

Stainless steel (SUS304)

(EX-13□ and EX-19□ only)

●

Apply a slit mask when detecting small objects or for increasing the accuracy of sensing position. However, the sensing range is reduced when the slit mask is mounted.

Model No. Description Material

OS-EX10-12

OS-EX10-15

OS-EX10E-12

(Note)

Note: Excluding EX-19□.

●●The slit mask should be mounted on the sensor be-

fore mounting the sensor. If the front sensing type sensor is used along with the

Slit mask for front sensing type only (hole diameter: φ1.2mm)

Slit mask for front sensing type only (hole diameter: φ1.5mm)

Slit mask for side sensing type only (hole diameter: φ1.2mm)

Stainless steel (SUS304)

slit mask and the optional sensor mounting bracket

I/O CIRCUIT DIAGRAMS

EX-□A(-R), EX-□B(-R) / NPN output type

●

Sensor circuit

Internal circuit Users' circuit

Note:

The emitter of the thru-beam type sensor does not incorporate the output.

EX-□A-PN, EX-□B-PN / PNP output type

●

Sensor circuit

Internal circuit Users' circuit

Note:

The emitter of the thru-beam type sensor does not incorporate the output.

Symbols... D

: Reverse supply polarity protection diode

: Surge absorption zener diode

Tr1

: NPN output transistor

Tr2

: PNP output transistor

Color code

)

(

)

t (

)

Color code

)

t (

)

(

12 to 24V DC ±10%

for the front sensing type, MS-EX10-1 or MS-EX10- 11, as shown in the figure below, a 0.2mm, or more, thick spacer is separately required.

0.2mm, or more, thick spacer is separately required.

M3 screws

INTENDED PRODUCTS FOR CE MARKING

●

The models listed under ' SPECIFICATIONS' come with CE Marking. As for all other models, please contact our office.

SUNX Limited

Overseas Sales Dept. (Head Office)

2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan Phone: +81-(0)568-33-7861 FAX: +81-(0)568-33-8591

Europe Headquarter: Panasonic Electric Works Europe AG

Rudolf-Diesel-Ring 2, D-83607 Holzkirchen, Germany Phone: +49-8024-648-0

US Headquarter: Panasonic Electric Works Corporation of America

629 Central Avenue New Providence, New Jersey 07974 USA Phone: +1-908-464-3550

URL : sunx.jp

PRINTED IN JAPAN