SRC-3000b
Touch Screen Smart Remote Control
User’s Manual
040130
Preface
About this manual
This manual is designed to make it easy to use the SRC3000b Touch Screen Remote Control as easy as possible.
Information in this document has been carefully checked
for accuracy; however, no guarantee is given to the
correctness of the contents. The information in this
document is subject to change without notice.
Copyright
© Copyright 2004
This document contains proprietary information protected
by copyright. All rights are reserved. No part of this manual
may be reproduced by any mechanical, electronic or
other means, in any form, without the prior written
permission of SUNWAVE Technology Corporation.
Trademarks
All trademarks and registered trademarks are the property
of their respective owners.
SUNWAVE Customer Service & Support Info
E-Mail: info@sun-wave.com
URL: www.sun-wave.com
i
Table of Contents
Chapter 1 Introducing the SRC-3000b .............1
1.1 SRC-3000b Features ............................................................... 2
1.2 Unpacking the SRC-3000b.................................................... 2
1.3 Identifying Components....................................................... 3
Chapter 2 Getting Started .................................4
2.1 Inserting the Batteries ............................................................ 4
2.1.1 Battery Indicator...................................................... 4
2.1.2 Battery Tips and Precautions ................................. 5
2.2 About the Touch Screen....................................................... 6
2.2.1 Turning the Touch Screen On................................ 6
2.2.2 Touch Screen Precautions .....................................6
2.2.3 Using the Touch Screen Soft Keys ......................... 7
2.2.4 Accessing Setup...................................................... 7
Chapter 3 Setting Up the SRC-3000b................9
3.1 Customizing the LCD Layout................................................ 9
3.2 Code and Learn Setting Key .............................................11
3.3 Using Pre-programmed Code to Program Devices ....... 12
3.4 Using Learning Function to Customize SRC-3000b .........15
3.4.1 Before Using Learning Function .......................... 15
3.4.2 Learning from Another Remote Control............ 15
3.4.3 Deleting Key Codes and Device Codes ...........19
3.5 Resetting the SRC-3000b to Factory Defaults.................. 20
3.6 Macro Function.................................................................... 22
ii
3.6.1 Creating a Macro ................................................. 22
3.6.2 An example to create a Macro ........................ 24
3.6.3 Macro Interruption ................................................ 26
3.6.4 Viewing the Macro Key ....................................... 26
Chapter 4 Miscellaneous Settings..................27
4.1 Using the Transmission Function......................................... 27
4.2 Setting the Backlight ........................................................... 29
4.2.1 Setting the Backlight............................................. 29
4.2.2 Setting Backlight Sensitivity................................. 30
4.3 Turning Off the Beep Signal ............................................... 31
Chapter 5 Controlling Devices .......................32
5.1 Alternating Between Screens ............................................ 32
5.2 Controlling Devices ............................................................. 32
Appendix A Functions and Specifications ... 33
Functions ..................................................................................... 33
Specifications ............................................................................. 34
Appendix B Accessories ............................... 35
Appendix C Troubleshooting........................36
Troubleshooting Tables ............................................................. 36
iii
Chapter 1 Introducing the SRC3000b
Congratulations on your purchase of the SRC-3000b Touch
Screen Remote Control. The SRC-3000b is a digital universal
remote control that is easy to use, enabling you to control
all of your electronic devices equipped with an infrared (IR)
remote.
The SRC-3000b uses a user-friendly Touch Screen panel. You
can control up to eight devices, including VCRs, DVDs, TVs,
and satellite dishes.
The SRC-3000b enables you to quickly configure each
device in your household or office by using the innovative
“learning eye” feature. In addition, the advanced Macro
function enables you to initiate a chain of up to 60
commands with the touch of a single key.
The SRC-3000b, a simple and user-friendly remote, provides
you with a complete central control solution.
NOTE:
This manual helps you to learn how to use the advanced
features of the SRC-3000b. However, it does not explain how
to use the functions of your devices. Please refer to the user’s
manuals of your devices for further information.
1
SRC-3000B User’s Manual
1.1 SRC-3000b Features
z Large touch screen display
z Macro function, each Macro can store 60
commands at most
z Controls up to eight devices including DVDs, TVs,
Satellite Receivers, VCRs, and CDs
z Learns the IR codes from your existing remotes to
control your devices quickly
z Pre-programmed codes for many remote controls
z User-programmable keys for each device, up to 56
keys in total
z Automatic shutoff after 90 seconds of inactivity
1.2 Unpacking the SRC-3000b
After unpacking the SRC-3000b, please check out the
contents to make sure that the following items are included.
1. SRC-3000b
2. User’s Manual
3. Pre-programmed Code List
If any of the above items is missing or appears to be
damaged, please contact your dealer immediately. Please
do not throw the package away in case you need to ship
your SRC-3000b.
2
1.3 Identifying Components
1.3 Identifying Components
Refer to the following illustration to identify the components of
the SRC-3000b.
1. Infrared Eye
Point the infrared eye at
the device you want to
operate.
2. Light Sensor
Detects ambient light to
automatically turn on the
backlight.
3. LCD Touch Screen
The LCD panel enables you
to configure and operate
your devices by touching
the screen.
4. Backlight
Automatic blue backlight
illuminates in a dim
environment.
5. Device keys
Press these keys to display
the LCD layouts for the
specific devices as below.
1. Infrared Eye
2. Light Sensor
3.
LCD Touch Screen
4. Backlight
5. Device Keys
6. Learning Eye
Point your original remote
control to the learning eye
and press the
corresponding keys to send
out the IR signals; so that
the SRC-3000b can learn
the IR codes for your
devices.
6. Learning Eye
Figure 1: Front View
3
Chapter 2 Getting Started
This chapter provides the information helping you to use the
SRC-3000b quickly.
2.1 Inserting the Batteries
The SRC-3000b operates on three AAA alkaline batteries
(not included in the package). Batteries must be inserted
before you can operate the SRC-3000b.
1. Lift the battery cover.
2. Insert three AAA batteries according to the polarities
inside the battery compartment.
3. Snap the battery cover back.
2.1.1 Battery Indicator
Battery low icon
Figure 2: The Battery Low Icon
When the power of batteries is weak, the “battery low” icon
is displayed in the upper right corner.
4
2.1 Inserting the Batteries
2.1.2 Battery Tips and Precautions
1. The SRC-3000b will not lose programmed data when
batteries are replaced.
2. Please always use fresh batteries. Alkaline batteries
are recommended. Do not mix different types of
batteries.
3. Ensure that positive (+) and negative (–) polarities of
the batteries match the diagram inside the
compartment.
4. Do not expose the batteries to excessive heat or
flame.
5. Keep batteries out of the reach of children.
6. Weak batteries reduce the effective distance of the
unit. Replace batteries immediately when the
icon appears.
7. To reduce the danger of leakage, remove batteries
when used longer than two years.
5
SRC-3000B User’s Manual
2.2 About the Touch Screen
The Touch Screen changes the number of soft keys
according to the device that is selected.
2.2.1 Turning the Touch Screen On
Turn on the SRC-3000b by touching the screen. The SRC3000b turns itself off after 90 seconds of inactivity.
2.2.2 Touch Screen Precautions
Please review the following information carefully before
using the SRC-3000b.
1. Tap the LCD Touch Screen gently.
2. Do not use a pen or any sharp object to tap the
screen.
3. The SRC-3000b is not waterproof. Keep the touch
screen dry and never immerse it in liquid. Wipe off
any spills immediately.
4. Don’t expose SRC-3000b to extreme temperatures.
Keep it away from heat sources.
5. Avoid dropping the SRC-3000b or putting anything
on the touch screen.
6. Clean the LCD touch screen with a soft cloth. If
needed, dampen the cloth slightly before cleaning.
Never use abrasives or cleaning solutions.
6
2.2 About the Touch Screen
2.2.3 Using the Touch Screen Soft Keys
The Touch Screen Soft Keys enable you to operate the SRC3000b and your devices. You can use these keys to
program codes from your original remotes, to control your
devices, and to set up command sequences called Macros.
You will hear a beep when you press a key. To turn on or off
the beep, please refer to page 31. Besides, the SRC-3000b
turns itself off after 90 seconds of inactivity.
2.2.4 Accessing Setup
To setup the SRC-3000b, press a
function key for 3 seconds till the
confirmation screen appears. The
confirmation screen is designed to
prevent you from accidentally
modifying your remote. Please
press the four number keys in any
order to start to setup the remote.
7
SRC-3000B User’s Manual
The following table provides an overview of major key functions.
Name & Key
Icon
Device keys
Code Setup key
Macro key
Delete key
Function Setup Description
Device setting
and LCD layout
Setup device
code, manually,
automatically or
by learning
function
Setup Macro
Delete and reset
to default
Key: Enter device setting and
arrange the LCD touch screen layout
to correspond to your remote control.
(P.9)
You can also toggle device pages by
pressing the key again.
Code: Enables you to enter preprogrammed codes. (P.11)
Learn: Enables the remote to learn
codes from other remote controls
directly. (P.15)
Enables you to set Macro function.
(P.27)
You can also view the Macro setting
by pressing the key.
Key: Erase key codes. Refer to P.19.
Bank: Erase device codes. (P.19)
Key & Bank: Reset to factory default.
(P.20)
System setup
key
Transmission,
backlight and
beep setup
Backlight: Setup backlight lasting
period and sensitivity. (P.29)
Code: Transmit all data. (P.27)
Beep icon: Turn the beep sound
on/off. (P.31)
After finishing setting, press the OK
key to confirm your decision.
Figure 3: Major Function Keys
The following chapters describe each function in detail.
8
Chapter 3 Setting Up the SRC3000b
Before the SRC-3000b can be used to control a device, it
needs to be configured to display your existing remote
control keys and it must be programmed to send the
correct infrared signals.
This chapter guides you through the Touch Screen layout
and SRC-3000b setup procedures.
NOTE:
The SRC-3000b includes eight default devices;
including TV, satellite TV, VCR, DVD player, hi-fi stereo,
radio/cassette player, CD player, and auxiliary.
3.1 Customizing the LCD Layout
Layout edit mode enables you to customize the SRC3000b’s LCD layout to match your original remote controls.
1. Press and hold the desired
device key for three
seconds to enter the
confirmation screen.
2. Press each number button
(2, 4, 6, 8) in any order until
they disappear to enter the
set up mode.
9
SRC-3000B User’s Manual
3. Select a key you want to
modify. Press that key
repeatedly to scroll through
the available icons for the
key.
NOTE:
You can press
the available icons.
4. Repeat step 3 to modify all
desired keys.
5. After finishing customizing
the layout, press
confirm the changes and
leave the mode.
to display all
to
NOTES:
a. You can press at any time to exit the mode
without saving any changes.
b. You can press the device key to change the
pages.
10
3.2 Code and Learn Setting Key
3.2 Code and Learn Setting Key
SRC-3000b is equipped with two functions, pre-code and
Learning Function, to get the right codes for your target
devices.
Pre-Code
You may configure all keys on SRC-3000b by entering
a specific four-digit code number. This may be the
fastest way to program the SRC-3000b. To get the
specific code number, please refer to the supplied
pre-programmed code list.
However, it requires that the device you intend to
program is included in the pre-programmed code
database. Some newer or less-common devices may
not be pre-programmed, and their codes must be
learned by using the Learning Function.
Learning Function
You can use this function to learn the IR codes
directly from another remote control. This function is
perfect for newer or less common devices. You can
also use the function if a certain key does not perform
the desired function after using the CODE function.
However, if you have the problem that the SRC-3000b
cannot learn your device codes, please refer to
“Troubleshooting” on page 36 or contact SUNWAVE.
11
SRC-3000B User’s Manual
3.3 Using Pre-programmed Code to Program
Devices
You can follow these instructions to program a device by
using pre-programmed codes.
There are two ways for you to collect the right codes within
the function:
A. Manually Programming remote by Code.
B. Automatically Programming remote by Code
A. Manually Programming remote by Code.
1. Select a device you want to
program (For example, TV).
2. Press and hold
seconds to enter the
confirmation screen.
3. Press each number button (2,
4, 6, 8) in any order until they
disappear and start to use the
Pre-Code function.
4. Press
through the options until you
reach the icon
and enter code setup page.
and to scroll
for 3
. Press
12
3.3 Using Pre-programmed Code to Program Devices
5. Locate your target device’s
four-digit code in
Preprogrammed Code List and
enter it.
NOTES:
a. Some codes are designed to operate more than one
model. It may take several trials to find the code that fits
your device.
b. When you enter the four-digit code number and the icon
is displayed, it could be that the code number
doesn’t exist in the Pre-programmed Code List
c. Each device classification can be used to control anther
type of device. You just need to enter the four-digit code
number.
Example:
You have two different TVs, TV1 and TV2. And you want to
integrate the two TVs in SRC-3000b.
1. Please load the codes for TV1 by entering the four-digit
code number for the TV deice.
2. You can select another device (for example, DVD) and
load the codes for TV2 by entering the four–digit code
number.
3. In this way, you can control TV1 in TV device and control
TV2 in DVD device.
13
SRC-3000B User’s Manual
B. Automatically Programming remote by Code
1. Please follow step1-4 stated in
Manual Entry section.
2. Turn on the target device you
want to control and point the SRC3000b to the target device.
3. Press
Function. SRC-3000b will send out
IR codes to find the correct ones.
4. When the target device is turned
off, touch any part of the screen
immediately to stop the searching.
5. Press
that the codes are suitable for the
device. Test the
device is turned on again, this
means you have already found
the proper codes for your devices.
6. Press
SRC-3000b.
to start Auto Search
and to ascertain
key if the
to save the codes in
NOTES:
a. When getting the right codes, you can press to show
the four-digit code number. In this way, you can enter the
code number directly in the future.
b. You can press
saving any codes.
c. Each device can automatically search the target device
codes under the same classification only. For example,
within TV device, Auto Search will just find the codes for TV.
at any time to exit the mode without
14
3.4 Using Learning Function to Customize SRC-3000b
3.4 Using Learning Function to Customize SRC3000b
You can use Learning Function to get the codes directly
from the original remotes.
3.4.1 Before Using Learning Function
Before you start to use Learning Function to get the codes,
please pay attention to the followings:
1. Before using Learning Function, please delete the
original codes saved in the specific device. For
example, to operate the living room TV instead of the
bedroom TV, please delete all the codes (for the living
room) saved in TV device at first. And then learn the
codes for the TV in the bedroom.
2. Learning Function does not work with all devices.
3. All keys except the Code Setup key, Delete key, Macro
key, and System setup key can be learned.
3.4.2 Learning from Another Remote Control
Please put the original remote and SRC-3000b on a flat
surface. And then have the original remote pointed to the
learning eye of SRC-3000b. The distance between two
remotes ought to be 2-4 inches (5-10 cm).
15
SRC-3000B User’s Manual
1. Select a device you want to
program.
2. Press and hold
seconds to enter the
confirmation screen.
3. Press each number button (2,
4, 6, 8) in any order until they
disappear and start to use the
function.
4. Press
through the options until you
reach the icon
press
selection.
5. Select a device (for example
TV) in SRC-3000b.
and to scroll
to confirm your
for 3
. And then
16
3.4 Using Learning Function to Customize SRC-3000b
6. Have your original remote
pointed to “Learning Eye” at
the bottom of SRC-3000b.
7. The blinking key denotes the
key to be learned. To make
SRC-3000b to get the code for
the key, please press the
corresponding key on the
original remote for about 2-3
seconds until the icon
displayed on the LCD. If the
icon
repeat step 7.
8. The SRC-3000b will
automatically guide you to
learn the next key. When you
finish learning all the keys,
please press
mode.
appears, please
to exit the
is
17
SRC-3000B User’s Manual
NOTES:
a. Although SRC-3000b will guide you to learn each key,
you can also select any key to learn as you want by
touching it directly. You can also change the page by
touching the device key.
b. If a key has been programmed with a code, the icon
appears on the LCD. You can overwrite the code
by learning directly.
c. The SRC-3000b screen displays the icon
3000b learns the code successfully.
if SRC-
d. You can press
finishing learning all the codes.
e. The device key can also save a code. To have the
device key to learn a code, press the key for 3 seconds
until it is blinking. Please follow step 7 to get the code
for the key. When SRC-3000b learns the code
successfully, the icon
at any time to exit the mode when
will also show up.
18
3.4 Using Learning Function to Customize SRC-3000b
3.4.3 Deleting Key Codes and Device Codes
You can follow these instructions to delete a code in a
single key or all the codes in a device.
1. Press and hold the
for 3 seconds to enter the
confirmation screen.
2. Press each number button
(2, 4, 6, 8) in any order until
they disappear and start to
use the function.
3. Press
through the options and
select the icon
you want to delete.
4. And then press
confirm your selection.
5. If you select
delete a code from a single key. Please press the
specific device key you want to delete (for example
TV) in advance. And then press the specific key to
delete the code saved in it.
and to scroll
mode, it means that you intend to
key
or that
key to
NOTE: Device keys can also save codes (You can refer to
page21). To delete the codes saved in device keys,
press the device key for one second. If you delete
the code successfully, the icon
6. If you select
delete all the codes saved in the device. Just press the
mode, it means that you intend to
will appear.
target device key and press
delete all the codes saved in the target device.
7. Press
to leave the function.
. In this way, you will
19
SRC-3000B User’s Manual
3.5 Resetting the SRC-3000b to Factory Defaults
This function enables you to reset the SRC-3000b to the
factory default configuration.
NOTE: All Macros and programmed keys will be deleted when
you reset the SRC-3000b to factory defaults.
1. Press and hold the key
for 3 seconds to enter the
confirmation screen.
2. Press each number button
(2, 4, 6, 8) in any order until
they disappear and start to
use the function.
3. Press
and to select
mode.
4. And then press
confirm your selection.
5. To avoid resetting the remote
accidentally, the
confirmation screen will
appear again.
6. If you really intend to reset
the SRC-3000b, please press
the four numbers(2,4,6,8)
again.
key to
20
3.5 Resetting the SRC-3000b to Factory Defaults
7. The icon
briefly on the screen to tell
you that the SRC-3000b
returns to the factory
defaults.
appears
21
SRC-3000B User’s Manual
3.6 Macro Function
A Macro includes a series of commands. Macro function
enables you to initiate a sequence of up to 60 commands
just with a single key. You can use any key as your Macro
key and insert time delays into the sequence. However,
please remember that it will disable the original key
function when you use the key as your Macro key.
3.6.1 Creating a Macro
Please refer to the following steps to create a new
Macro key.
1. Press for three seconds
to enter the confirmation
screen.
2. Press each number button
(2, 4, 6, 8) in any order until
they disappear and start to
use the function.
3. When you are in the mode,
the icon “
the upper part of the LCD.
4. Please press a device key
you want to use for you
Macro (for example TV). And
then press any key to use it
as the Macro key. You hear
three beeps to indicate that
you are ready to setup your
Macro key.
” flashes on
22
3.6 Macro Function
NOTE:
If you select a key that already has been used
as a Macro key, the new setting will replace
the old Macro setting.
5. Press any key as the commands saved in the Macro
key.
NOTES:
a. You can choose any key in
any device. You just need to
press the device key directly
to select different keys.
b. You can setup the delays
between the two commands.
Please press
the time of delay. The time of
delay ranges from 1 to 9
seconds.
and decide
6. Press
setting or
setting.
to confirm your
to cancel the
23
SRC-3000B User’s Manual
3.6.2 An example to create a Macro
The following example will help you better understand
creating a Macro sequence. It is provided to teach you
how to create a Macro. By no means it is the only Macro
sequence you can create. You can create Macros using
any sequence of commands you desire.
The following Macro example will:
1. Turn the TV on.
2. Switch the TV to Video mode.
3. Turn the DVD player on.
4. Create a five-second delay.
5. Play a DVD.
Set up the example macro using the following steps:
1. Press and hold
confirmation screen.
2. Press each number key (2, 4, 6, 8) in any order until they
disappear and
3. Select TV device key
device will be used to start the macro in the normal
operation mode.
for 3 seconds to enter the
begins flashing.
. Then, press “1” in the TV
NOTES:
a. 1 will no longer perform its original function.
b. If you select a key that already has a macro stored
in it, the new macro replaces the old one.
c. Do not use one of the eight DEVICE KEYS to run
your Macro.
4. Press
watch the DVD.
24
to switch to Video mode so that you can
3.6 Macro Function
5. Press to switch to the DVD device menu so you can
construct a series of commands for the DVD player.
6. Press
turning on the DVD player and playing a DVD.)
7. Press
8. Press the desired time delay. In this case, press 5.
9. Press
10. Press
(You may need to set a time delay between
, and a number pad appears.
.
to confirm setting.
NOTES:
a. Press at any time while creating a macro to
exit macro mode.
b. You may create another macro at this time by
entering another sequence of commands.
c. If trying to create a Macro with
you must press and hold
This is to prevent a accidentally overwriting a
tape.
d. You cannot include another Macro key in the
Macro key you are setting. If you do so, the
Macro you are newly adding won’t still send out
the commands saved in another Macro key.
Running a Macro
1. TV turns on.
2. TV switches to Video mode.
3. DVD player turns on.
4. Five-second delay.
5. DVD player starts playing DVD.
for two seconds.
under VCR,
25
SRC-3000B User’s Manual
3.6.3 Macro Interruption
After pressing the preset Macro key for a device, you
can interrupt the command sequence by pressing
then
appears and the macro stops.
3.6.4 Viewing the Macro Key
You can view which keys are used as Macros for any
particular device. Follow these instructions:
1. Press the device key (for
example
2. Press
Macro keys will be
displayed on the LCD.
For example, if you set
number 9 as a Macro key
for on PAGE 1 in the TV
device, the preset Macro
key ”9” will appear when
TV).
and then the
,
you press the
3. If you want to check the
Macro key on Page 2, press
the device key to switch to
the second device page,
and then repeat Step 2.
key.
26
Chapter 4 Miscellaneous Settings
This chapter will tell you how to use transmission function,
setup the backlight, and adjust the beep.
4.1 Using the Transmission Function
The SRC-3000b can transmit customized data to another
SRC-3000b.
NOTE:
Before using this function to transfer data, you must
connect two SRC-3000b with SLC-2080 USB cable (optional
accessory). You can refer to Appendix B for more
information about the cable.
1. Press and hold for 3
seconds to enter the
confirmation screen. You
only need to operate on the
programmed SRC-3000b.
2. Press each number button
(2, 4, 6, 8) in any order until
they disappear and start to
use the function.
3. Press
icon
and to select the
. And then press
to begin the
transmission.
4. During the transmission, the
LCD displays blank keys as
shown in the illustration on
the next page.
27
SRC-3000B User’s Manual
5. When the transmission is
completed, an icon
will be displayed on the LCD.
If the transmitting fails, an
icon
6. For a double transmission,
repeat Step 3.
will show up.
7. You can press
cancel the transmission.
NOTES:
Before transferring the data, please pay attention
to 3 points:
a. The two SRC-3000b remote controls have fresh
batteries.
b. These remotes are turned on.
c. These remotes are connected by the USB cable.
to
28
4.2 Setting the Backlight
4.2.1 Setting the Backlight
1. Press and hold for 3
seconds to enter the
confirmation screen.
2. Press each number button (2, 4,
6, 8) in any order until they
disappear and start to use the
function.
3. Press
4. Press a numerical key 1-6 to
select the backlight lasting time.
and to select the icon
. And then press t he key
to start the setting.
4.2 Setting the Backlight
5. Press
NOTE:
The backlight lasting time can be set from 10 to 60
seconds in 10-second increments, '1' for 10 seconds,
'2' for 20 seconds, and so on.
to save your settings.
29
SRC-3000B User’s Manual
4.2.2 Setting Backlight Sensitivity
1. Press and hold for 3 seconds
to enter the confirmation screen.
2. Press each number button (2, 4,
6, 8) in any order until they
disappear and start to use the
function.
3. Press
start the setting.
and to select the icon
. And then press to
4. Press
light sensor sensitivity.
The frames above indicate the
sensitivity of the SRC-3000b. More
frames will light-up the backlight
more easily.
5. Press
press
without saving.
or to adjust the
to save the settings or
to leave the mode
NOTES:
a. The more frames you select, the more sensitively the
backlight reacts to the ambient lighting.
b. The light sensor sensitivity ranges from 1to 8.
c. When you touch the LCD, the SRC-3000b activates
the backlight automatically according to the
environment.
You can save the power by adjusting the backlight lasting
time and the sensitivity of light sensor.
30
4.3 Turning Off the Beep Signal
4.3 Turning Off the Beep Signal
1. Press and hold for 3
seconds to enter the
confirmation screen.
2. Press each number button
(2, 4, 6, 8) in any order until
they disappear and start to
use the function.
3. Press
and to select the
icon
to start the setting.
4. Press
change the different beep
pitch or turn off the beep
sound.
5. Press
settings or press
leave the mode without
saving.
. And then press
or to
to save the
NOTE:
The number key shows the different pitch of the
beep. When beep is turned off, the icon
disappear on the LCD.
to
will
31
Chapter 5 Controlling Devices
The SRC-3000b is designed to be simple and straightforward
to operate. This chapter explains how to use the SRC-3000b
to control all your devices.
NOTE:
This chapter assumes you have already set up the SRC3000b and saved all the IR codes for the keys. You can
refer to Chapter 3 Setting Up the SRC-3000b on page 9
for more information about how to get the IR codes.
5.1 Alternating Between Screens
Press a device key to alternate between page 1 and
page 2.
5.2 Controlling Devices
1. Make sure the SRC-3000b is pointing to the target device.
2. Tapping the Touch Screen gently.
3. Select a device key and give remote commands as
usual.
If the icon
doesn’t have IR code.
appears, it means that the pressed key
NOTE:
The Record Key (Within VCR Device, page 1)
must be held down for two seconds. It is a
double-confirmation design to prevent users
from overwriting a tape accidentally
32
Functions
Appendix A
Functions and Specifications
Functions
• 8 in One IR learning type and pre-programmed remote
control
• High performance MCU capable of upgrading programs
• 512 KB Flash Memory for Learning/pre-programmed codes,
so that you never lose your data when removing your
batteries.
• Each device includes up to 56 keys on two pages
• Capable of learning carrier (frequency: 20KHz-455 KHz)
and pulse codes
• Capable of deleting single key, single device or all remote
codes
• Flexible LCD layout
• Each Macro key can save up to 60 commands, including
time delays between commands
• The commands included in a Macro key will be shown on
the LCD while the Macro key is working.
• Backlight works automatically according to the
environment
• Automatic Power Saving Function
• Motion detector to turn on SRC-3000b automatically
• Battery low indicator
33
SRC-3000B User’s Manual
Specifications
Model SRC-3000b
Dimensions (WxHxD) 3.1 x 7.5 x 1.25 inches
(7.9 x 19 x 3.2 cm)
Weight (without Batteries) 210 g
Number of Device 8 devices
Keys 2 pages/56 keys/ each device
Backlighting Blue LED
Learning Frequency 20 KHz – 455 KHz & pulse up to
256 bits long
Memory 512 KB flash memory
Batteries AAA x3 Alkaline batteries
Power Consumption LCD Off: 50 µA
LCD On: 300 µA
Operation: 30–150 mA (Max.)
Operating Distance Approx. 30 feet (8-10 meters)
Interface UART/115,200 bps (optional
SLC-2080 USB cable)
IR Distance 8-10 meters
LCD Screen (W*H) TN LCD 2.3 x 4.8 inches
(5.8 cm x 12 cm)
34
Appendix B Accessories
SLC-2080 USB cable
The SLC-2080 USB cable is an optional USB cable that
transfers the data between two SRC-3000b. All settings
including MCU firmware, settings in the flash memory and
pre-programmed codes will be transferred by
transmission function described in Chapter 4
“Miscellaneous Settings.”
By connecting a transmit wire between two SRC-3000bs,
you can also duplicate settings and functions from one
SRC-3000b to another.
35
Appendix C Troubleshooting
Troubleshooting Tables
Problem Solution
LCD does not show
anything when you
touch it.
The SRC-3000b
doesn’t operate a
device.
You see “ERROR”
displayed during
operation.
1. Batteries may be dead. Replace
the batteries with three new AAA
alkaline batteries (page 4)
2. Check that the batteries are
properly installed.
1. Make sure that the desired device
key on the SRC-3000b LCD panel
has been selected.
2. Move closer to the device. The
maximum operating distance is
approximately 30 feet.
3. Ensure that you are aiming the
SRC-3000b directly at the device
and that there are no obstructions
between the SRC-3000b and the
device.
4. Ensure programming with the
learning function (page 15) or the
manufacturer codes has been
properly done.
5. Learn code the key (page 10).
1. The key that you pressed has not
been taught.
2. Teach the key using the learning
procedure (page 15).
36
Problem Solution
Troubleshooting Tables
You cannot operate
a device even after
using the Learning
Function.
You see “ERROR”
display on the LCD
during the learning
procedure.
Your VCR will not
record.
Macro does not
work.
1. Make sure that your SRC 3000 has
correctly learned the target
device’s remote control code
(page 15).
2. Delete the device data from the
SRC-3000b and carry out the
learning function again (page 15).
3. Make sure you did not program
more than one remote for a given
device.
1. Make sure you hold the target
remote’s key till the screen
displays Ok or Error on the screen.
2. Make sure the two remotes are
not too close or too far apart keep them about 2~4 inches
(5~10 cm) apart, and your device
remote control is aiming directly at
the SRC-3000b’s learning eye.
1. As a safety feature on the SRC-
3000b, you must press the REC key
for two seconds.
1. Be sure to aim the SRC-3000b at
the devices while the Macro
commands are being sent.
2. Macro was not properly set up.
Repeat Macro set-up procedure
(page 22).
37
SRC-3000B User’s Manual
Problem Solution
IR LEARNING is not
successful.
A key of your
existing remote
performs two or
more functions
1. Replace batteries in the SRC-3000b
and the remote you are trying to
configure.
2. Keep the distance between the
remote control and the SRC3000b’s learning eye to about 2~4
inches.
3. Do not use the learn function near
an incandescent lamp.
4. Memory capacity is full (56 keys for
each of eight models).
5. The learning process has no errors,
but you still can’t control your AV
devices: repeat the learning
procedure again. If you still can’t
solve the problem, contact
Sunwave for help.
6. Original remote might not be
compatible with learning
procedure.
Some remotes issue multiple
commands when a key is held down.
Please be sure to teach different keys
of SRC-3000b for these different
commands. Each key of SRC-3000b
can only learn one command.
The LCD screen turns
off.
38
The SRC-3000b is preset automatically
to switch the LCD off after the Power
Down time (90 seconds). Just tap the
touch screen to turn the SRC-3000b
back on again.
Loading...