Sunwave Tech. SR1200 Instructions For Use Manual

Download

Page 1

CRESCENT STAR — SR1200

Universal Remote Control

Remote Control Online Database plus Smart Learning

Instruction For Use (IFU)

Page 2

1. Infrared Transmitter

2. LED Indicator

3. Power Button

4. Mute Button

5. Device Mode Keys

6. Function Keys

7. Battery Compartment

8. USB Connector

Page 3

Table of Content

Package Content

How to install batteries

How to set up the URC Register your URC – 1st time registration ONLY

Easy Online Setup Smart Learning (Fast Learning)

Operating the URC

Maintenance

Trouble-shooting

5 6

Page 4

Congratulations! Your Universal Remote Control (URC) is a state-of-the-art device which integrates many different Infra-red remote controls to deliver instant A/V control action to your ﬁngertips.

Before operating the remote, please read thoroughly 1) descriptions of the coversheet and 2) this manual. Then, reserve them for future reference.

1. Crescent STAR - Universal Remote Control

2. USB Cable

3. Instruction For Use (IFU)

• Microsoft Windows XP/Vista/7

• 512MB RAM & 300MB Free Disk Space

• Available USB2.0 Port x 1

• Installed Microsoft Internet Explorer 8.0

• Established Reliable Internet Connection

Remarks: Due to security reason of Microsoft Windows Vista/7, the setup program and drivers of your URC will not be executed automatically (Program auto-run is prohibited). Please double click the pop up window – CD ROM Drive – KRMAP and the KRMAP.exe to install the program and drivers manually.

Your URC can replace up to 8 original A/V remote controls. Before your URC can operate your A/V devices, ﬁrstly you have to register your URC. Then, you can go through one of the following SIMPLE set up procedures to set up your URC.

PACKAGE CONTENTS

PC SYSTEM REQUIREMENTS (MINIMUM)

Alkaline batteries are always recommended. The number of battery required is stated on the back side of the package coversheet.

1. Remove the battery cover on the back side of your URC.

2. Observe the polarity of the batteries and the “+/–“ marks inside the battery compartment.

3. Insert the batteries accordingly.

4. Push the battery cover back in place.

Remarks: Whenever you see the LED indicator of your URC ﬂashes 3 times after you press any key, it tells your URC batteries are running out. Please replace with the new and fresh alkaline batteries to ensure proper operation and performance.

HOW TO INSTALL BATTERIES

HOW TO SET UP THE URC

Page 5

By Easy Online Setup – a reliable internet connection and PC system loaded with Windows XP/Vista/7 is required – please make sure you have a PC system loaded with Windows XP/ Vista/7, installed with Microsoft Internet Explorer 8, and it is connected to a reliable internet connection throughout the whole setup process. – please also have your AV device Brand and Model number ready

By Smart Learning

Please follow the simple setup procedures on the Online Remote Code Database webpage throughout the whole setup:–

1. Remove the battery cover on the back side of your URC.

2. Make sure your URC is loaded with fresh batteries.

3. Locate the mini USB connector inside the battery compartment.

4. Connect your URC with the provided USB cable to your PC (via one of the available USB Port).

5. Once, your URC is connected to your PC, the installation program will be started automatically (all necessary device drivers will be installed to your PC automatically, ONLY for the 1st time connection/setup); when the installation is completed, your PC will launch a browser (Internet Explorer) to reach our online database server.

Remarks: If your browser is not running after the connection of your URC

to the PC, you have to double-click the icon (KRMAP.exe) manually

on your desktop to start (for Windows Vista/7 user).

For the new user, you have to register your URC by ﬁlling in your name and email address. Simply follow the below procedure and you can activate your URC in a second.

Once all the necessary drivers and auto-run program has been installed, you will be prompted at the following page.

Simply ﬁll in your information under the space provided with * marks and then, click to send your ﬁle. Your URC will be activated and ready for further set up.

Conrm

Page 6

Easy Online Setup

1. Select Remote Setup page, you will see the following:

2. On the Remote Setup page, simply select your Device type (e.g. TV), type in your Device name (e.g. SONY KV-J29MH9), select Brand – SONY from the drop down list and select Model from the drop down list.

3. Repeat step 2 for the rest of your other devices, such as VCR, DVD, SAT,

CBL, STB, etc.

4. Press to re-conﬁrm your selected setting.

5. Press to activate the data ﬁle.

Set up your URC via one of the below set up method:–

By Easy Online Setup or By Smart Learning

Preview

Create

Page 7

6. Press to download the data ﬁle automatically to your URC.

WARNING:

DO NOT try to press for data ﬁle download. For security reason, each URC has been limited to 5 attempts for SAVING the data ﬁle to the user’s local computer. After that, your URC will be LOCKED. Please make sure that this is really necessary for such action.

7. Disconnect the USB cable from your URC. Turn on your device (e.g. TV), try the function keys on the URC. If your device (e.g. TV) responds to your invoked function correctly, your URC has been loaded with the right Device Code. Otherwise, repeat the above set up instructions with the rest available Device Codes until your device (e.g. TV) responds to your invoked function, and most keys work correctly.

Remarks:

– Always keep secure connection of your URC and the PC system while the whole Easy Online Setup process. – After the remote code is downloaded to your URC, simply disconnect it from the USB cable and try the function. – If you want to quit the set up mode during the Easy Online Setup

procedures, simply close the browser on your PC or disconnect the connection between the PC and URC.

– If you cannot ﬁnd a correct Device Code for your equipment, you

should try to select a code with a similar description of your device. (e.g. if your TV is 29XUMH, where you can see a 32XUMH on the available code, you can try to use this code 32XUMH, as the manufacturers tend to use the same remote code for a series of products; simply reconnect your URC with your computer and try another available codes (refer to the above steps.)

– If only some of the commands are worked for your device, you can

either select another code or try to learn the rest of the commands to your URC from your original remote, see By Smart Learning section.

– Do NOT try to press for data ﬁle download. For security reason,

each URC has been limited to 5 attempts for SAVING the data ﬁle to the user’s local computer. After that, your URC will be LOCKED. Please make sure that this is really necessary for such action.

Open

Save

Page 8

Smart Learning (Fast Learning)

If you cannot ﬁnd your URC a correct Device Code for your equipment from the Online Database, you can copy your original A/V remote control commands to your URC via Learning. Your URC allows you to capture up to 360 additional remote control commands and all 8 device modes can facilitate learning in a second. Please follow the below instruction to start: (Do not forget to have your original A/V remote control ready for your learning process)

1. Select a desired Device Mode (e.g. TV, if you want to set up your URC to

operate your TV).

2. Press and Hold the Device Mode key (e.g. ) for 3 seconds, the LED

indicator will light up.

3. Release the Device Mode key (e.g. ).

4. Press and Release a desired key on the URC you want to hold the command, the LED will ﬂash slowly. (Now aim your A/V remote control to the URC Infra red Lens on a ﬂat surface with 1–3 cm apart. Make sure your A/V remote control is loaded with fresh batteries).

5. Press and Hold the corresponding key on

your original A/V remote control to transfer the command. The LED indicator of the URC will ﬂash. When the command has been learnt successfully, the LED indicator will stay on. You can release the key on the A/V remote control. If the LED

indicator keeps ﬂashing quickly, it shows error in learning process. Adjust the position of both remote controls and repeat steps 4 & 5 again.

6. Repeat steps 4 & 5 to transfer other commands into the rest of the

function keys.

7. When you ﬁnished the whole device mode, Press and Hold the corresponding Device Mode key (e.g. ) for 3 seconds to save all the learnt command and exit the learning mode.

Remarks:

– Your URC will quit the learning mode automatically after 30 seconds of idle period. – If you want to quit the learning mode at any time, simply Press and Hold the corresponding Device Mode key for 3 seconds. – Downloading a new Device Code from the Online Setup will automatically erase and replace all learned commands in the chosen device mode. – When you ﬁnished learning the original remote to your URC, you can

upload your URC to our ONLINE DATABASE for future retrieval, simply connecting your URC with your PC, the system will prompt for your action automatically.

– Master Reset of URC will erase your learned commands.

1–3 cm

Page 9

Normal Operation

Once you have set up the URC for your A/V equipment, it works like your original remote controls. To operate, just aim it at your equipment, press an appropriate device mode key and invoke the desired function by pressing a corresponding key on the URC. The indicator ﬂashes during signal transmission and as conﬁrmation of key touch.

Master Reset/ResetDefault

Master reset allows you to reset your URC to its factory default state. (After Master Reset, you have to set up the URC from beginning. Before you do this, please make sure it is really necessary).

1. Remove the battery cover on the back side of your URC.

2. Make sure your URC is loaded with fresh batteries.

3. Locate the mini USB connector inside the battery compartment.

4. Connect your URC with the provided USB cable to your PC (via one of

the available USB Port).

5. Once, your URC is connected to your PC, it will launched a browser

(Internet Explorer) to reach our online database setup server.

Remarks: If your browser is not running after the connection of the URC to your PC, you have to double-click the icon (KRMAP.exe) on your desktop.

6. On the Remote Setup page, simply click button once.

OPERATING THE URC

ResetDefault

Remarks: Master Reset of URC will erase ALL learned commands as well.

7. Click button once and wait patiently for 1 minute, your URC

will be reset to factory default

Create

Page 10

Q. My URC does not work at all!

A. Check if you have set up your URC by Easy Online Setup or Smart Learning. A. IMPORTANT REMARKS for Windows Vista/7 users, after you connect your URC to your computer, please double click the pop up window – CD ROM Drive – KRMAP and the KRMAP.exe to install the program and drivers. A. Check your A/V device, if the device’s main switch is turned off, your URC could not operate your device. A. Check whether your batteries are inserted properly and are in correct +/– marks. A. Check whether you have pressed the corresponding device mode key for your device. A. If the batteries are low, replace the batteries. A. Try to connect your URC to your PC and reload the user data by selecting on the Remote Setup Page.

Q. If several Device Codes are listed under the brand of my A/V device, how can I select the correct Device Code?

A. To locate the correct Device Code that is similar to your device model number, as manufacturers tend to use the same remote for a series of products. A. To locate the correct Device Code for your A/V device, test the code one by one until most keys work properly.

Q. My A/V equipment responds only to some of the commands.

A. You have set a code for which only some commands work properly but some do not. Try other codes until most keys work properly. A. You can learn the rest of the missing commands from your original remote, see Smart Learning section.

Q. Some learned commands in my URC do not work.

A. Those commands are not learned properly. Try to teach your URC again for those functions. A. Check the batteries inside both A/V remote and your URC. If the batteries are weak, the URC cannot learn command properly. You have to replace all batteries for proper functioning.

TROUBLE-SHOOTING

1. Do not expose your URC to dust, strong sunlight, humidity, high

temperature or mechanical shock.

2. Do not use old and new batteries together as old batteries tend to leak.

3. Do not use corrosive or abrasive cleaners on your URC.

4. Keep the unit always dust free by wiping it only with soft and dry cloth.

5. Do not disassemble your URC, it contains no user-serviceable parts.

MAINTENANCE

UserCong

Page 11

Page 12

830-1200-5001