Sunstone DEDVL15, DEDD42 Installation Manual

All Designer Doors are "Self-Rimming", meaning that whatever the
Cut-Out edge looks like, as it is always rough, the product rim will
cover all edges. Specific to Designer Doors.

1. Follow Cut-Out dimensions provided on product Specification
sheet, after removing door from packaging, insert door frame in to
cut-out of island wall.

2. Open Doors, locate the small pre-drilled holes, see small bend on inner flange,
this cups around inside edge, or push into inner cut-out frame wall securing door.
Match screw type or installation type to your "Type of Installation Method" listed
below. For Wood use Deck Screws, Metal Studs use Self-Tapping Screws,
Masonry either use Concrete Bolt - or Concrete, careful - some types may make it
difficult to remove door if needed. Use Clear Silicone around outside edge of

door frame to seal against water moisture and rain.

3. Handles are mounted to inside of door frame, remove these and re­mount to outside of each door, careful not to scratch the finish with tip of
screw driver.
If doors are uneven adjust door hinge with Screw driver, adjust the back
screw to move door closer or further from frame, this is also the screw to
remove the door from frame, or hinge if needing replaced. Adjust Center
Screw to elevate hinge away from frame.

PLACING:

MOUNTING:

ADJUSTING:

DESIGNER SERIES DOORS
INSTALLATION GUIDE

EXAMPLE: ADJUSTING

EXAMPLE: MOUNTING

EXAMPLE: PLACING

Designer Series Doors & Drawers are configurable both Vertically & Horizontally, follow these steps for proper installation. Designer Series
Components are designed to Match with our Stainless Steel Cabinet Islands.

TECHINICAL SUPPORT

888-934-9449 Press 1

[e-mail]

ADD 3/4" WIDTH IN CUTOUT

WHEN COMBINING MOLTIPLE

COMPONENTS TOGETHER BOTH

HORIZONTALLY & VERTICALLY

COMBINE MULTIPLE COMPONENTS IN ANY COMBINATION

WHEN MOUNTING TO FRAME, PLACE
TIGHT SIDE BY SIDE, WITH DRAWERS
REMOVED, SECURE TOPS, BASES & SIDES
TO INNER FRAME.

3-3/4" Inside

Flange Depth

CUT-OUT WIDTH

CUT-OUT HEIGHT

Inside edge is bent down
to Cup around inside edge

Loosen the back
screw to slide forward
or remove from frame

Tighten center screw to
raise hinge off frame

TYPES OF INSTALLATION METHODS

1.2.3.

WOOD FRAMED ISLAND: For Wood Framed Island Construction is Extremely important Not to use any wood within 24"
Inches of BBQ Grills. Wood frame is fine for Bar/Sink areas and or Storage compartments. If your island is mostly wood,
just substitute for Metal Studs while within the 24" Inches of BBQ Grill. When installing Door to all Wood Framed Islands,
locate the Pre-Drilled holes on the inside rim of Door perimeter. Locate some "Deck Screws" in your hardware section of

HOME DEPOT.

METAL STUD FRAMED ISLAND: This is the most common type of Outdoor Kitchen Island, for most "Modular Type"

Islands, and even many islands built on-site use Metal Studs as their choice of construction material. It is a superb
building material for many reason, easy to work with, fire-proof, and sturdy as it is available in many Gauge thickness for
whatever the use. When installing your Door with this type of construction, you will need to use a "Self-Tapping Screw's" ­which are available in plastic boxes usually in the Hardware section of your HOME DEPOT store.

MASONRY CONCRETE BLOCK ISLAND: The use of Masonry materials is very common among Contractors/Pool Builders,
who use materials like Cinder Blocks very often preferring this type of construction for it's Low-Cost attributes and easier
building methods. If your Island is built in this way, you must pay closer attention to the Cut-Out Width & Height, since the
average Block Height is 4", 8" or 12" Inches and will not allow for any variance to these measurements without actually
cutting into the stone. Use a Hammer-Drill and a Concrete Drill Bit to make the Holes, then use the Hammer-Drill once again
this time using a Self-Tapping Concrete Bolt. Other methods include using the masonry's concrete mortar around back frame
of door, or even using "Nail-Glue", important note - for either of these other methods you will not be able to remove your door
later if needed. Locate The Hammer-Drill, Concrete Drill Bit in the Hardware Section, or Concrete & Masonry Blocks in the
Building Materials Section of your local HOME DEPOT store.

1/16" INCH BEVELED
FRAME ALLOWS UNITS
TO BE CONFIGURED BOTH
HORIZONTAL & VERTICLE
ALL WITHIN A SINGLE
CUT-OUT

Mount Door Frame to Inside of
Cut-Out, see Pre-Drilled Holes
on inside of Door Frame Flange

Re-Mount Handle from
inside of door panels
to outside.