Sunrise spas 780 SR, 870 SR, 870 S, 870 SX, 880 S Owner's Manual

...

SPA OWNER’S MANUAL

http://www.sunrisespas.com

OM-SUNRISE-18E

IMPORTANT SAFETY INSTRUCTIONS

READ & FOLLOW ALL INSTRUCTIONS

SAVE THESE INSTRUCTIONS

Pour voir ou imprimer ce document en Français, veuillez visiter:

European Sunrise Spas 2018 Ow ner’s Manual

INDEX

Table of Contents

CONFIGURATION TABLE ........................................................................................................................................................................................................................................................... 3

CONGRATULATIONS ON THE PURCHASE OF YOUR NEW SPA ......................................................................................................................................................... 3

YOUR PERSONAL SPA DATA ................................................................................................................................................................................................................................................ 6

IMPORTANT SAFETY INSTRUCTIONS ........................................................................................................................................................................................................................... 7

INSTALLATION INSTRUCTIONS ....................................................................................................................................................................................................................................... 10

ELECTRICAL CONNECTION GENERAL INFORMATION ............................................................................................................................................................................ 12

EUROPEAN 50HZ MODELS ................................................................................................................................................................................................................................................. 13

TYPICAL RESIDUAL CURRENT DETECTOR (RCD) ........................................................................................................................................................................................ 14

230 VOLT SUPPLY CONNECTION ................................................................................................................................................................................................................................ 14

CONVERSION FROM SINLGE SERVICE TO 3-SERVICE ............................................................................................................................................................................ 16

WHAT’S INSIDE YOUR SPA .................................................................................................................................................................................................................................................. 17

WHAT’S UNDER YOUR SPA (THE EQUIPMENT) .............................................................................................................................................................................................. 20

START-UP.............................................................................................................................................................................................................................................................................................. 21

TP600 – SIMPLIFIED MENUS CONTROL PANEL USER GUIDE ......................................................................................................................................................... 24

TP600 – REGULAR MENUS CONTROL PANEL USER GUIDE ............................................................................................................................................................ 37

MP3/BLUETOOTH READY SYSTEM OPERATION .......................................................................................................................................................................................... 62

ACCESSING FILTER CARTRIDGES ............................................................................................................................................................................................................................... 63

MAINTENANCE ................................................................................................................................................................................................................................................................................ 64

FILTER SYSTEM

DRAINING YOUR SPA ................................................................................................................................................................................................................................................................ 67

WINTERIZING YOUR SPA ....................................................................................................................................................................................................................................................... 68

TROUBLESHOOTING YOUR SPA ................................................................................................................................................................................................................................... 69

WATER TREATMENT GUIDE ............................................................................................................................................................................................................................................... 76

.............................................................................................................................................................................................................................................................................. 66

DOC: OM-SUNRISE-18E

European Sunrise Spas 2018 Owner’s Manual

Note:

Line

Model

Frame/Bottom

Filter

Keypad User Guide

BRAND CONFIGURATION TABLE

670 S/SR Polysteel/Tray Whitewater (Dual) TP600 Simplified

770 S/SR Polysteel/Tray Whitewater (Dual) TP600 Simplified

780 S/SR Polysteel/Tray Whitewater (Dual) TP600 Simplified

The factory default for spas using the TP600 keypad is Simplified Menus. However, more keypad settings and features are possible on some spas by accessing the Standard menus within the spa pack. A spa pack set up change is required to access these settings and features within the standard menus.

Ask your dealer about the set up change required and additional keypad instructions.

870 S/SR/SX Polysteel/Tray Whitewater (Dual) TP600 Regular

880 S/SR/SX Polysteel/Tray Whitewater (Dual) TP600 Regular

970 S/SR/SX Polysteel/Tray Whitewater (Dual) TP600 Regular

980 S/SR/SX Polysteel/Tray Whitewater (Dual) TP600 Regular

CONGRATULATIONS ON THE PURCHASE OF YOUR NEW SPA

We have tried to compile a complete, easy to understand manual all about your spa and its' maintenance. Years of research and development have gone into producing the superior quality product you have purchased. Your spa is made from the highest quality material and latest technology available today. Pride and meticulous attention to detail have resulted in the spa you have chosen. With proper care, your spa will provide many years of comfort and pleasure.

Please take a few minutes now to read all of the instructions before you install your spa. This owner's manual will help you understand your spa, so you will get the most from your investment. For service and advice, do not hesitate to call your authorized dealer. Your questions will be welcomed by friendly and knowledgeable staff.

May you have as much pleasure and enjoyment using your new spa, as we had making it for you.

We understand there are many choices in the marketplace when you are

considering adding a s pa t o your home, so thank you for choos ing a spa by Leisure

Manufacturing Inc. Enjoy!

DOC: OM-SUNRISE-18E

European Sunrise Spas 2018 Ow ner’s Manual

SAFETY SIGN

IMPORTANT NOTICE: SAFETY SIGN

Enclosed with this Owner’s Manual is a Safety Sign. This sign must be permanently installed in a location that is visible to all spa users. It is the spa owner’s responsibility to remind all users about safe spa use, particularly occasional users of the spa, who may not be aware of the various health and safety issues.

To obtain additional or replacement copies of the safety sign, contact your dealer.

ATTENTION: SPA OWNER

In the immediate vicinity of the spa, a sign must be posted stating the following:

1) The spa’s address

2) Location of the nearest telephone with posted emergency numbers

3) Nearest available police department, fire department and ambulance/rescue unit

DOC: OM-SUNRISE-18E

European Sunrise Spas 2018 Owner’s Manual

As a new spa owner, you have specific obligations in regards to the installation and safe use of this spa. Failure to do so may result in a loss of warranty coverage not to mention personal injury to those using this spa.

CONDITIONS OF WARRANTY AND CONSUMER OBLIGATIONS

Inspect the spa upon its arrival for damage. If you are being made aware of this for the first time, your spa may not have been delivered in its original factory packaging. If this is the case, please take time to inspect your spa and report any damage or missing items to your dealer.

1) Install the spa both physically and electrically, in accordance with any local codes.

2) Provide suitable access to all sides of the spa. Any custom built enclosure, either above or below a deck

surface, must be able to be removed with relative ease.

3) Provide sufficient work area around the spa’s perimeter especially the side the spa’s equipment is located on.

4) Regularly check operation of the spa in regard to filtration, jet pump operation and the heating system.

5) Report any concern to the dealer. Any problem that arises towards the end of particular warranty coverage

should be documented and reported to the dealer

6) Maintain the water’s chemical balance and clean/replace the system’s cartridge filter(s) as instructed by the

dealer and/or Leisure Manufacturing Inc.

7) Drain and refill the spa on a regular basis as instructed by the dealer and/or Leisure Manufacturing Inc.

8) Winterize and store the spa and its’ components in accordance with the manufacturer’s printed instructions.

9) Care for and maintain the spa cabinet, hard cover and acrylic surface as outlined in these instructions.

10) Ask your dealer to record the spa’s serial number on your bill of sale.

11) Provide a copy of your bill of sale, if requested by the dealer or Leisure Manufacturing Inc.

DOC: OM-SUNRISE-18E

European Sunrise Spas 2018 Ow ner’s Manual

Model Year

Model Name/Number

Spa Serial#

Jet Pump(s) Size (HP, SPL, Watts etc.)

Heater size (kw)

Filter Cartridge (Model Number/Size)

Topside Control/Keypad

Spa Pack Model #

Spa Pack Serial #

Dealer Name

Date of Purchase

We strongly recommend that you attach your bill of sale to this manual after installation is complete. Keep it in a safe place for future reference. You may also wish to attach any notes you have made about the dealer delivery, dealer start up demo or any other notes that may be of benefit in the future.

YOUR PERSONAL SPA DATA

Before you begin the installation of your new spa please take a few minutes to fill out the details of your spa. This information will become invaluable later should you have a question for your dealer or should you need to make a warranty claim. Ask your dealer to assist you in recording this information.

DOC: OM-SUNRISE-18E

European Sunrise Spas 2018 Owner’s Manual

DANGER:

WARNING:

IMPORTANT SAFETY INSTRUCTIONS

WARNINGS

children. To avoid accidents, ensure that children cannot use this spa unless they are supervised at all times.

pump. Should the need arise to replace the suction fittings or the pump, be sure that the flow rates are compatible.

Never operate spa if the suction fittings are broken or missing. Never replace a suction fitting with one rated less than the flow rate marked on the original suction fitting.

installed within 5 feet of metal surfaces if each metal surface is permanently connected by a minimum 8 AWG (8.4mm

within 5 feet (1.5m) of a spa.

Risk of Accidental Drowning. Extreme caution must be exercised to prevent unauthorized access by

Risk of Injury. The suction fittings in this spa are sized to match the specific water flow created by the

Risk of Electric Shock. Install at least 5 feet (1.5m) from all metal surfaces. As an alternative, a spa may be

) solid copper conductor to the wire connector on the terminal box that is provided for this purpose.

Risk of Electric Shock. Do not permit any electrical appliance, such as a light, telephone, radio, or television,

To reduce the risk of injury:

a) The water in a spa should never exceed 40°C (104°F). Water temperatures between 38°C (100°F) and 40°C

are considered safe for a healthy adult. Lower water temperatures are recommended for young children and when spa use exceeds 10 minutes.

b) Since excessive water temperatures have a high potential for causing fetal damage during the early months of

pregnancy, pregnant or possibly pregnant women should limit spa water temperatures to 38°C (100°F).

c) Before entering a spa, the user should measure the water temperature since the tolerance of water

temperature-regulating devices varies.

d) The use of alcohol, drugs, or medication before or during spa use may lead to unconsciousness with the

possibility of drowning.

e) Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory system

problems or diabetes should consult a physician before using a spa.

f) Persons using medication should consult a physician before using a spa since some medication may induce

drowsiness while other medication may affect heart rate, blood pressure, and circulation.

CAUTION:

Maintain water chemistry in accordance with the manufacturer's instructions.

DOC: OM-SUNRISE-18E

European Sunrise Spas 2018 Ow ner’s Manual

DO NOT connect your spa to an extension cord.

READ AND FOLLOW ALL INSTRUCTIONS

When using this equipment, basic safety precautions should always be followed. Including the following:

a) A green coloured terminal or a terminal marked G, GR, Ground, Grounding or the international grounding

symbol is located inside the supply terminal box or compartment. To reduce the risk of electric shock, this terminal must be connected to the grounding means provided in the electric supply service panel with a continuous copper wire equivalent in size to the circuit conductors supplying this equipment.

b) At least two lugs marked "BONDING LUGS" are provided on the external surface or on the inside of the

supply terminal box or compartment. To reduce the risk of electric shock, connect the local common bonding grid in area of the hot tub or spa to these terminals with an insulated or bare copper conductor not smaller than No.6 AWG.

c) All field-installed metal components such as rails, ladders, drains or other similar hardware within 3m (10ft) of

the spa or hot tub shall be bonded to the equipment grounding bus with copper conductors not smaller than No.6 AWG.

SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

Hyperthermia

Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 37°C (98°F). The symptoms of hyperthermia include drowsiness, lethargy, and an increase in the internal temperature of the body. The effects of hyperthermia include:

• Unawareness of impending hazard

• Failure to perceive heat

• Failure to recognize the need to exit spa

• Physical inability to exit spa

• Fetal damage in pregnant women

• Unconsciousness and danger of drowning

The use of alcohol, drugs or medication can significantly

increase the risk of fetal hyperthermia.

DOC: OM-SUNRISE-18E

WARNING:

European Sunrise Spas 2018 Owner’s Manual

CAUTION:

WARNING:

IMPORTANT SAFETY INSTRUCTIONS FOR SPAS WITH AUDIO SYSTEMS

Do not operate the audio/video controls while inside the spa.

speakers, headphones, additional audio/video components etc).

These units are not provided with an outdoor antenna. When provided, it should be installed in accordance with article 810 of the National Electrical Code, ANSI/NFPA 70.

Do not service this product yourself as opening or removing covers may expose you to dangerous voltage or other risk of injury. Refer all servicing to qualified service personnel.

If the power supply connections or power supply cord(s) are damaged; if water is entering the audio/video compartment or any electrical equipment compartment area; if the protective shields or barriers are showing signs of deterioration; or if there are signs of other potential damage to the unit, turn off the unit and refer servicing to a qualified service personnel.

Risk of Electric Shock. Do not leave compartment door open.

Risk of Electric Shock. Replace components only with identical components.

Prevent Electrocution. Do not connect any auxiliary components to the system (example: cable, additional

This unit should be subjected to periodic routine maintenance (example: once every 3 months) to make sure that the unit is operating properly.

DOC: OM-SUNRISE-18E

European Sunrise Spas 2018 Ow ner’s Manual

will drain away harmlessly.

INSTALLATION INSTRUCTIONS

Remember, your new spa is a powerful piece of electrical and plumbing equipment. You owe it to yourself, your family and your friends to install it correctly and safely. Before attempting to hook-up or use your spa, please read the following instructions.

ATTENTION:

This spa is intended for outdoor use, however it can be installed indoors

when precautions are taken to ensure the spa is installed and located

in such a manner that any water that could leak, splash or be released as humidity

POSITIONING OF YOUR SPA - CONSIDERATIONS

Your spa is completely self-contained. Therefore, you can situate it just about anywhere; on a patio, in or on a deck, in a basement or sunroom. It comes completely pre-plumbed and water tested from the factory. Never lift or carry the spa by the plumbing. Damage could occur which would not be covered under warranty.

You should take into account the following when selecting prospective spa sites in order to maximize enjoyment.

To avoid any personal injury or damage to your spa, have 4-5 people ready to assist you to move the spa to its' final location. Use a moving dolly and/or straps to more evenly distribute the spa's weight. Never lift or carry the spa by its' plumbing.

SITE CONSIDERATIONS

Local codes Local building, property and electrical codes may affect your installation.

Delivery access to location

Vegetation in spa area Trees, bushes, flowers etc. can all add to spa maintenance.

Spa location relative to buildings

Fences, tree lines

Spa step out location

Spa Direction View when using a lounger & ease of access for servicing.

Gates, overhangs, fences, gas meters, and AC units may become obstructions. You may need to access from a neighbour's yard or employ a crane.

The location could add to your spa maintenance (removing snow from cover) and increase operating costs.

More privacy during use and serves as a wind break but may also add more maintenance.

Any surface that is slippery when wet could be dangerous for bathers both entering and exiting the spa.

Downspouts and natural drainage of land

Outside water supply and draining location

Optional accessories These may take up added space that you must plan for (cover remover/holder).

DOC: OM-SUNRISE-18E

These may flood the spa area, damage spa or create a safety hazard to bathers.

You will need a place to safely drain the spa and a way to refill it easily.

European Sunrise Spas 2018 Owner’s Manual

Damage caused by improper spa installation will void factory warranty.

Do NOT locate your spa in a low run-off area since melting snow or rain can cause pump and equipment damage. WATER SHOULD ALWAYS DRAIN AWAY FROM THE SPA.

SPA SUPPORT

Whatever the support is, it must be:

a) A continuous, level surface, above grade, capable of handling 80 lbs. per sq. ft. that will not be compromised by

changes in the water table or water sitting in the area.

b) Such that the weight of the spa, water and bathers is not supported by the spa lip. c) In full contact with the bottom of the spa

ACCEPTABLE SPA SUPPORT BASES

Concrete Pad 4" to 6" thick with provision for run off Patio Stones, Pavers etc. Levelled with proper preparation of the earth Wooden Deck Floor Incl. centre support uprights in concrete and joists spaced 12" on centre Engineered Plastic Spa Pad Following pad manufacturer's instructions

Unacceptable Spa support bases include crushed gravel, stone dust, bare earth, platform built directly onto earth.

See next page for dimensions that can be used to determine the proper location of submerged conduits in concrete slab installations. All dimensions are made from the outside of the spa's frame with the access panels removed.

DOC: OM-SUNRISE-18E

European Sunrise Spas 2018 Ow ner’s Manual

ELECTRICAL CONNECTION GENERAL INFORMATION

A. LOCATING A CONDUIT WITHIN A CONCRETE PAD

If your intent is to bring a conduit and power wires up under the spa we suggest that it enter the spa cavity in the front, left corner; 6” (15cm) Dimension A in from the left and 6” (15cm) Dimension B up from the front. See A & B on the diagram below. This location will allow you to stay clear of spa pumps and other equipment while giving you a short and easy access to the left side of the spa pack, where the electrical entry hole and terminal block are located.

B. SUPPLY CABLE ENTRY INTO SPA EQUIPMENT AREA

• You may enter the spa cavity at any other point around spa provided you have reviewed the location and

determined there is no interference. You may also decide to enter at an adjoining wall (depending on the positioning of the spa) and route a conduit along the spa kicker. Ask your electrician for his/her advice in these matters.

• In all cases the best side for entry of the supply cable is the side to your left when you are standing at the

equipment panel.

• Right side entry is possible; however, this may involve additional supply cable, parts and time.

HOW TO PASS THE CABLE THROUGH THE SPA ENCLOSURE

Polysteel Frame with Polyethylene Bottom and Polysteel Panels

a) You can choose to notch the polysteel panel so you can pass the cable/conduit through and still be able to

remove/replace the panel for servicing. You should consider securing the cable or conduit to the spa’s metal frame where cable/conduit passes through the cabinet.

b) You may also route a cable up under the corner. The curved panel is flexible enough and there is enough

space to run the cable this way. Removing the corner may help you to do this easier.

c) On a concrete pad where you have a conduit or cable coming up within the perimeter of the spa, you can

easily cut an opening in the polyethylene bottom to access the cable or conduit/wires. See above table for recommended opening location.

You may wish to insulate any opening or cut-out you make in the spa’s cabinet panel or corner or bottom to keep cold air and small animals out.

DOC: OM-SUNRISE-18E

European Sunrise Spas 2018 Owner’s Manual

Read and Follow ALL Directions

THIS IS NOT A CONDITION THAT IS COVERED UNDER THE

SPA PACK MANUFACTURER’S WARRANTY OR

LEISURE MANUFACTURING’S COMPREHENSIVE SPA WARRANTY.

EUROPEAN (50HZ) MODELS

Please note the following important information: When using this electrical equipment, basic safety instructions should be followed, including the following:

(1) This spa must be connected to an RCD (Residual Current Detector) with a residual operating current not

exceeding 30mAmps.

(2) Electrical installation must be carried out by a qualified electrician strictly in accordance with local governing

codes.

(3) A terminal marked "ground" is located within the control box. To reduce the risk of electric shock this terminal

must be connected to the grounding means provided in the electric supply service panel with a continuous copper wire equivalent in size to the circuit conductors supplying the equipment.

(4) At least two lugs marked "bonding lugs" are provided on the external surface of the control box. To reduce the

risk of electric shock connect the local common bonding grid in the area of the hot tub or spa to these terminals with an insulated or bare copper conductor not smaller than No. 6 AWG.

(5) Test the RCD before each use of the spa, according to the manufacturer's instructions. (6) Before servicing any electrical components of the system make sure that the power supply is switched off. (7) Keep the door closed in order to provide IPX5 protection to the electrical compartment.

Any opening made through the spa enclosure for the entry of input cables/wires,

must be made watertight to preserve the IPX5 rating of the appliance.

ATTENTION: ELECTRICIAN & SPA OWNER

PICO FUSE

Balboa Spa packs contain a special fuse, referred to a “Pico fuse”.

This special fuse is designed to open (burn out) if:

a) There is any problem with how the electrical supply is connected

b) There is a power surge to the spa pack

This fuse is not replaceable and the entire spa pack is considered destroyed.

WARNING!

DOC: OM-SUNRISE-18E

European Sunrise Spas 2018 Ow ner’s Manual

Power Requirements:

Single Service

IMPORTANT:

<- Two Pole RCD

Typical specifications are as follows:

<- Four Pole RCD

SRBP601E Spa Pack

TYPICAL RESIDUAL CURRENT DETECTOR (RCD)

A residual current device (RCD,) is the generic term for a device that monitors the current in the line conductor and the neutral conductor of a circuit in an earthed system.

In a circuit that’s operating properly, the vector sum of the live and neutral current values added together will be zero. Current flowing to earth, due to a line earth fault, will return via the earth conductor, and regardless of load conditions, will be registered as a fault. This current flow will give rise to a residual current that will be detected by the device. If the residual current exceeds the rated sensitivity of the RCD, it will automatically activate a tripping of the faulty circuit.

Residual Current Devices ( RCD’s ) range Sensitivity - from 10 to 500mA Voltage - 2 poles : 230V; 3/4 poles: 230/400V Connection capacity

- 25A: 6/10 mm² (flexible/ rigid cable)

- 40,60A: 16/25 mm²

- 80,100A: 35/50 mm²

230 VOLT SUPPLY CONNECTION

A) SRBP601E SPA PACK

230VAC, 50/60Hz, 1p, 16A (Circuit Breaker rating =20A max.)

230VAC, 50/60Hz, 1p, 32A (Circuit Breaker rating =40A max.)

1 x 32 Amp single service you must: a) Move dipswitch #2 on switchbank S1

to the ON position

b) Move dipswitch #5 on switchbank S1

to the OFF position

See wiring diagram (back of cover for spa pack) for switchbank location

[3 wires (line, neutral, ground)]

If you want to run this spa pack on a

DOC: OM-SUNRISE-18E

European Sunrise Spas 2018 Owner’s Manual

Power Requirements: Single Service

Dual Service

3-Service

IMPORTANT –

SRBP21, SRBP21X & SRBP21MS Spa Pack – Single Service

B) SRBP21, SRBP21X AND SRBP21MS SPA PACK

230VAC, 50Hz, 1p, 32A (Circuit Breaker rating =40A max.)

230VAC, 50/60Hz, 1p, 32A (Circuit Breaker rating =40A max.)

400VAC, 50Hz, 3p, 16A (Circuit Breaker rating =20A max each phase line.

[3 wires (line, neutral, ground)]

N/A

[5 wires (line 1, line 2, line 3, neutral, ground)]

Service must include a neutral wire, with a line to neutral voltage of 230VAC.

DOC: OM-SUNRISE-18E

European Sunrise Spas 2018 Ow ner’s Manual

SRBP21, SRBP21X & SRBP21MS

Spa Pack - 3-Service

Power Up Screen

Wire Size and Over Current Protection

Total Ampere Rating of

Power System

Minimum Wire Size

Use Copper ONLY

With 90°C Insulation

Ampere Rating of

RCD Circuit-breaker

CONVERSION FROM SINGLE SERVICE TO

3-SERVICE

1. Remove the jumper wire from J51 (Area 1) to J88 (Area 2)

2. Remove the jumper wire from J52 (Area 1) to J62 (Area 2)

3. Move the jumper wire attached to J60 from J36 in Area 3 to J45 in Area 4. (J60 to J45)

4. Move the jumper wire attached to J41 from J12 in Area 3 to J79 in Area 4. (J41 to J79)

5. Set DIP Switches A2 and A5 to OFF.

6. Terminal block must be wired according to the 3-Phase illustration on the wiring diagram

1. Line 1 – Brown

2. Neutral - Blue

3. Line 2 – Brown

4. Line 3 - Brown

Each time the system powers up, a series of numbers is displayed. After the start-up sequence of numbers, the system will enter Priming Mode. Next, refer to the User Guide for your keypad at the back of this manual.

OA to 16A #12 AWG 20 16A to 20A #10 AWG 25 20A to 24A #10 AWG 30 24A to 28A #8 AWG 35 28A to 32A #8 AWG 40

DOC: OM-SUNRISE-18E

European Sunrise Spas 2018 Owner’s Manual

Jet Type

Size

Adjustable Flow

Where it is most often used

3 ⅝” (92mm) 4 ⅜” (105mm)

Nozzle Type

Hydrotherapy Effect

Description

Fixed Stream

Neck Jets

Directional

Rifled

WHAT’S INSIDE YOUR SPA

HYDROTHERAPY JETS

A variety of jet sizes and internal styles are used in unique seating patterns to achieve superior hydrotherapy in individual spa models. Therefore, not every jet described or pictured below is in every model. Not all jet internal styles are available in all jet sizes.

To adjust the water volume, simply turn the jet face clockwise to the off position or counter clockwise to the maximum position. If you move too hard to maximum you will release the internal from the jet body.

Ozone/Cluster 1 ½” (38mm) No Seat backs, neck & shoulders, palm jets

Cluster 2 ¼” (56mm) Yes Palm jets, loungers, seat backs, calves, neck collars

Mini 3 5/16” (84mm) Yes Seat backs, footwells, loungers

Poly

Power 5 ¼” (133mm) Yes Seat backs, footwells, loungers

Yes Seat backs, footwells, loungers

A steady, non-adjustable stream of water.

100% shut off by using the stepped down/up movement of the face to move volume nozzle in/out

A steady volume adjustable stream of water with adjustable nozzle direction

A volume adjustable stream of water that gives the feel of a rotating stream of water without moving parts.

DOC: OM-SUNRISE-18E

European Sunrise Spas 2018 Ow ner’s Manual

Suctions

All suctions in our spas are VBG compliant for your safety.

Perimeter LED Lighting

Ozone/AquaNova Returns

Skimmer/Filter

Nozzle Type

Hydrotherapy Effect

Description

Twin Roto

Massage

Whitewater

(Sunrise)

OTHER INTERNAL FITTINGS

A volume adjustable jet with a fixed split nozzle that uses the water flow to deliver dual streams of water in a rotating pattern.

A volume adjustable stream of water that rotates. The combination of the moving inner mechanism and front face gives an ever changing pattern to the massage.

These multi-holed, anti-vortex fittings in the footwell provide the intake water for the pump(s). A powerful suction is produced here when the jet pumps are turned on. On systems with a circulation pump, the bypass suction fitting (smaller than regular suction), may have little to no suction on it, since the circulation pump has a lower flow than the jet pump and the suction is only active as the filter(s) become clogged.

These round or hex shaped, multi-faceted fittings, located on the vertical spa wall and deck of the spa, are the lenses for the LED light outputs.

These special thru wall fittings return water to your spa that has passed through the ozone or AquaNova system. If you do not have either ozone or AquaNova on your spa, these fittings will not be present.

This is the housing for your cartridge filter(s) and provides skimming action to remove surface debris. Some models have a removable basket from which debris can be dumped.

DOC: OM-SUNRISE-18E

European Sunrise Spas 2018 Owner’s Manual

Air Controls

On/off Water Valve

WATER FEATURES

LED Waterfall

LED Spa Light

Head Cushions

DECK CONTROLS

Wave

Located on the deck of the spa, these valves control the amount of air being mixed with the water stream at each jet. The minimum to maximum movement is approximately ¼ turn or on/off for toggle type. More air will increase the massage effect from the jet. Proper air draw is achieved when the jet pump is operating on high speed, particularly if the pump is a 2-speed pump.

This positive seal valve is used to turn the water feature on/off. Adjust it as needed to achieve the best effect from the water feature.

The LED waterfall located on a flat along the inside of the spa creates a relaxing sheet of water when turned on and adjusted using the on/off valve. When the Light key is pressed LEDs light up the waterfall body as well as the water sheet coming out of the waterfall.

MISCELLANEOUS

This clear or slightly bluish fitting is usually in the vertical surface of the spa steps. It is controlled by a designated switch on the keypad. It serves as a safety feature; lighting the spa's contours for those entering or exiting the spa.

The head cushions you will find in our spas are designed to add comfort to your spa experience. Whether it is just to rest you head as you sit back and enjoy the hydrotherapy or if it is to support your neck as you let our neck collar jets soothe your aching neck and shoulders, you'll find all our head cushions functional and comfortable.

DOC: OM-SUNRISE-18E

European Sunrise Spas 2018 Ow ner’s Manual

free standing spa pack

horizontal heater

2-Speed Jet Pump

Ozonator

03/UV Sanitizer (AquaNova)

Other items under your spa may include an audio power supply, audio receiver and LED control system.

WHAT’S UNDER YOUR SPA (THE EQUIPMENT)

The spa's control pack, circulation pump, heater, drain connection and ozonator may be accessed by removing the cabinet panel along the control side of the spa. Removing the panel(s) to the right or left of the spa's main access panel will allow access to the jet pumps, blower and any other optional equipment. On some models, all equipment is accessible from the main access panel.

The board) for the pump(s) blower, light, keypad etc., as well as the heat regulating system. The spa pack is also where the electrical supply connections are made. The

A high performance 2-speed jet pump provides the power to operate the various hydrotherapy jets in the spa, at the optimum level. On models without a circulation pump, the low speed of the pump is used to circulate the water so it can be filtered and heated. Some models may have a 2 lines allow easy servicing of the circ pump and heater. Safety clips on the valve shafts keep the valves open during use.

houses the receptacles and switching apparatus (circuit

jet pumps to properly power the jets. Gate valves in the plumbing

is attached to the bottom of the spa pack.

An ozonator is used to assist in water treatment. The corona discharge (CD) model produces ozone which is drawn into the spa water via the return plumbing.

This unit creates both ozone and UV in perfect synergy to sanitize the spa water. Ozone introduced into the unit’s chamber reacts with the UV light to create hydrogen free radicals for advanced oxidization potential (AOP). This results in only oxygen bubbles emerging from the dual return fittings.

DOC: OM-SUNRISE-18E

European Sunrise Spas 2018 Owner’s Manual

Clean-up Cycle

START-UP

HOW YOUR SPA WORKS

Circulating, Heating and Filtering

Dedicated 24/7 circulation pump or low speed of a 2 speed pump (depending on model). Immersion heating element within a stainless steel heater barrel.

Filter System

Single or two-cartridge system that is accessible from inside the spa.

Your spa may be equipped with a split filter system. One cartridge on jet pump 1 and the other on the circ pump. The clean-up cycle of the spa pack turns pump 1 on 30 minutes after you have shut it off or it times out. It will run for 30 minutes to help clean up the spa. This clean-up cycle is adjustable in 30 minute increments up to 4 hours.

Some topside controls, such as TP600, will not show a clean-up cycle adjustment, unless the set up number used is the one being used within the standard menu feature as opposed to the simplified menu. Contact your dealer to get the setup number changed. See also located in the Part B manual. See page 40-41 on how to change the clean-up cycle.

, within the TP600 User Guide with Standard Menu feature,

Hydrotherapy

A combination of up to three (3) single or 2-speed jet pumps provides a gentle, low-speed therapy or intense, highspeed therapy. The jets have directional nozzles, multiple directional nozzles, fixed nozzles or rotating nozzles. Most of the jets have the ability to have the water volume adjusted to your therapy needs.

Deck Controls

Air controls mix air with the water stream coming out of the jet. A diverter valve is used on some models to dedicate pump flow to specific groups of jets or share it amongst several jets. Models with the waterfall feature have a control valve to turn the waterfall on/off.

A digital topside control panel allows you to activate the pumps, blower and light plus set the temperature that you want the water to be. The topside display also shows error messages and tells you if any special spa pack features are operating, including protection against overheating and freeze-up.

Lighting

Your spa is equipped with a multi-LED spa light allowing you to enjoy the effects of a colour changing LED light system. LED lights around the perimeter of the spa create a special effect of colour changing lights.

DOC: OM-SUNRISE-18E

European Sunrise Spas 2018 Ow ner’s Manual

Light Sequence (Ultrabrite - with integrated output for additional LEDs)

Light Sequence (Sunlite or Glo LED Jets Feature/Option Where Available – Lighted Jets)

LED Light Operation

Your spa may be equipped with an LED light system consisting of perimeter lights, lighted water feature(s), lighted jets and a thru wall underwater spa light, depending on the spa model and options. The system is controlled using the LIGHT key on the topside control panel. The spa pack is factory set/programmed for simple on/off spa light operation. Note that not all colours are available on all LED systems.

Operation: To move from setting to setting simply turn the LIGHT key on/off. If the light is turned OFF for more than 5 seconds, the sequence automatically restarts at the last colour shown.

Slow Cycle White (Blue, Green and Red mix) Aqua (Blue and Green mix) Magenta (Blue and Red mix) Blue Gold (Red and Green mix) Green Red Flash Strobe

The System uses a special MZ controller that has a unique colour sequence.

Colour Wheel (Slow fade from colour to colour) Green Aqua Magenta Blue Red Colour Jump (A fast change from colour to colour)

DOC: OM-SUNRISE-18E

European Sunrise Spas 2018 Owner’s Manual

IMPORTANT:

Now, read about the keypad operation, user settings, system defaults, automatic functions and display messages

included in this manual (see User Guide in the Index).

Take a few minutes to try the various keys and features on your new spa.

Always view the temperature display before entering the water. For your own personal safety, do not enter when the temperature exceeds the maximum set point of 40°C (104°F).

FILLING YOUR SPA

Okay, your new spa has been connected to the power and you have a basic understanding of how the equipment works and what the jets can do for you. We know you are anxious to fill the spa and get it started, but please read this section carefully before you fill your spa.

1) Make certain that the breaker or fuse(s) that supplies your spa equipment is off.

2) Wash the spa surface thoroughly with warm water and a soft cloth only to remove any construction or

transportation debris.

3) Check that the drain connection is closed.

4) Check that the unions on the spa pack and pump(s) are tight. They can loosen during transportation.

5) Remove the filter cartridges. Open waterfall/water feature ON/OFF valve before filling. Refer to graphics on

valve handle or simply turn counter clockwise to open.

6) Begin filling the spa with a standard garden hose. Fill by inserting hose into filter body, in the case of a lilypad

style filter, or by positioning hose into a cartridge mount located in the filter well. Do not fill your spa with soft water (consult dealer). If possible, your source fill water temperature should not be less than 70°F (21°C). Do Not operate the spa with low water levels. A level 4" over the bottom of the skimmer mouth is recommended. Maximum initial water level should be 6” below the spa lip. Adjust as needed based on number of bathers using the spa. Consider adding an overflow to your spa if you are regularly having enough bathers in the spa to significantly raise the water level such that damage to equipment may occur.

7) Increase the fill pressure slowly to prevent surface damage by a jerking hose.

8) Visually check all lines for leaks and correct immediately. If you cannot stop the leak simply by tightening a

union or resetting an "O" ring or gasket, contact your dealer immediately.

9) Turn on the main power at your electrical panel.

10) The topside control panel will initialize and begin its’ start-up procedure. Then the system will start the

circulation pump(or low speed pump) and the heater.

11) Re-install the filter cartridges.

Once you feel comfortable with the operation of your spa's controls, set the temperature to the desired level (100°F/38°C is an excellent starting point). Close the air controls and cover the spa with your hard cover. Heat up times will vary based on volume of water in the spa, but you can generally expect 6-8 hours to reach maximum temperature. Spas running on 120VAC will have a longer initial heat-up time.

DOC: OM-SUNRISE-18E