Sunrise Medical Quickie, Sterling User Manual
Quickie®/Sterling®Melody
Melody
Supplier:
This manual must be given to the rider of this wheelchair.
Rider:
Before using this wheelchair read this entire manual and save for future reference.
Quickie®/Sterling®Melody
Distribuidor:
Este manual debe ser entregado al pasajero de esta silla de ruedas.
Pasajero:
Antes de usar esta silla de ruedas, lea este manual en su totalidad y guárdelo
para futura referencia.
Quickie®/Sterling®Melody
Fournisseur :
Ce manuel doit être remis à l'utilisateur / utilisatrice de ce fauteuil roulant.
Utilisateur / utilisatrice :
Avant d'utiliser ce fauteuil roulant, lisez entièrement ce manuel et conservezle pour le consulter ultérieurement.
Owner’s Manual
Manual de
Instrucciones
Mode d’emploi
QUICKIE®/STERLING
Improving People’s Lives
®
ENGLISH
I. INTRODUCTION
SUNRISE LISTENS
Thank you for choosing a Quickie®/Sterling®wheelchair. Before using your wheelchair please read this
manual carefully. It will provide you with all the information you will require. If you have any queries
about the use, maintenance or safety of your wheelchair, please contact your local Sunrise Medical
Service Agent. We want to hear your questions or comments about this manual, the safety and reliability
of your chair, and the service you receive from your Sunrise supplier. Please feel free to write or call us
at the address and telephone number below:
I. INTRODUCTION
SUNRISE MEDICAL, INC
Customer Service Department
7477 East Dry Creek Parkway
Longmont, Colorado 80503
USA
(800) 333-4000 or (303) 218-4500
Sunrise Medical, LTD
Customer Services
Sunrise Business Park
High Street Wollaston
West Midlands DY8 4PS
ENGLAND
International Telephone: +44 1384 44 66 22
In Canada: (800) 263-3390
Fax: +44 1384 66 44
E-Mail: sunmail@sunmed.co.uk
This wheelchair is designed for comfort, safety and durability and has been exhaustively researched and
tested by our experts. The wheelchair is classified as a category A vehicle under the European
Wheelchair Standard EN 12184.
It is intended for the use of people of all ages who may have difficulty walking distances or for periods of
time. It is ideal for indoor use and suitable for users up to 113.4 kg (250lbs) in weight. Plese see specifications. Differing user weights can cause performance variation. Maximum user weight tested using 250
lb test dummy.
It has been manufactured to comply with the requirements of the Medical Device Directive 93/42/EEC,
the radio interference requirements of EEC Directive 89/336/EEC and the battery charger requirements
of CE EEC Directive 73/23/EEC and 89/336/EEC.
Electro Magnetic fields, such as those emitted by shop alarms may be disturbed by use of the wheelchair.
The function of the wheelchair may also be disturbed by Electro Magnetic fields emitted by shop alarms.
Sunrise Medical is dedicated to providing products of exacting quality which conform fully and reliably to
the requirements of their intended use. We are BS/EN ISO9001 accredited which is the internationally
recognized standard for quality management systems. This approval ensures we provide quality in all
areas of our business from development through to final delivery. Should you require any further assistance then please contact your local dealer.
FOR ANSWERS TO YOUR QUESTIONS
Your authorized supplier knows your wheelchair best and can answer most of your questions about chair
safety, use and maintenance. For future reference, fill in the following:
Supplier: ______________________________________________________________________________
Address: ______________________________________________________________________________
______________________________________________________________________________________
elephone:
T
Serial #: ______________________________________ Date/Purchased: ________________________
101266 Rev. B
____________________________________________________________________________
2
ENGLISH
II. TABLE OF CONTENTS
II. TABLE OF CONTENTS
I. INTRODUCTION....................................................... 2
II. TABLE OF CONTENTS ............................................ 3
III. YOUR CHAIR AND ITS PARTS.............................. 4
IV. NOTICE - READ BEFORE USE................................ 5
V. EMI (ELECTROMAGNETIC INTERFERENCE)...... 5
A.What is EMI ............................................................... 5
B. What Effect Can EMI Have ....................................... 5
C.Sources of EMI .......................................................... 5
D.Distance From the Source......................................... 6
E. Immunity Level.......................................................... 6
F. Report All Suspected EMI Incidents .......................... 6
VI. GENERAL WARNINGS............................................. 6
A.Notice to Rider.......................................................... 6
B. Notice to Attendants................................................. 6
C.Weight Limit .............................................................. 6
D.Controller Settings .................................................... 6
E. EMI ............................................................................ 7
F. Safety Check-List....................................................... 7
G.Changes & Adjustments ............................................ 7
H.When Seated in a Parked Wheelchair....................... 7
I. Environmental Conditions......................................... 7
J. Terrain........................................................................ 7
K.Street Use.................................................................. 7
L. Motor Vehicle Safety ................................................. 7
M.Center of Balance...................................................... 7
N.Transfers .................................................................... 8
O.Reaching or Leaning................................................... 8
P. Dressing or Changing Clothes................................... 8
Q.Obstacles................................................................... 8
R. Driving in Reverse ..................................................... 8
S. Ramps, Slopes & Sidehills .......................................... 9
T To Reduce the Risk of Falls, Tip-over
or Loss of Control..................................................... 9
U.Ramps at Home & Work........................................... 9
V. Wheelchair Lifts ......................................................... 9
Curbs & Single Steps ................................................. 9
.
W
X.Stairs .......................................................................... 9
Y. Escalators................................................................... 9
ARNINGS: COMPONENTS & OPTIONS
VII. W
A.Armrests.................................................................... 10
B. Batteries..................................................................... 10
C.Cushions
D.Fasteners ................................................................... 10
.................................................................... 10
.......... 10
E. Footplate & Footrests ............................................... 10
F. Motor Locks .............................................................. 10
G.On/Off Switch............................................................ 10
H.Pneumatic Tires......................................................... 10
I. Seating Systems ......................................................... 10
J. Upholstery Fabric...................................................... 10
K.Wiring ........................................................................ 10
VIII. SET UP, ADJUSTMENT & USE................................ 11
Notes............................................................................. 11
Tools You Will Need ...................................................... 11
Check Out..................................................................... 11
A.Battery Case Removal ............................................... 12
B. Armrests Adjustment ................................................ 12
C.Seat Removal ............................................................. 12
I
X. OPERATING GUIDE.................................................. 13
A.Performance Control Settings................................... 13
B. Sunrise Medical Programmer Pad (Optional)............ 13
C.Thermal Roll-Back ..................................................... 13
D.Circuit Breakers......................................................... 14
E. Joystick Assembly...................................................... 14
F. Motor Lock................................................................ 14
X. BATTERIES.................................................................. 15
A.Introduction............................................................... 15
B. Battery Charger......................................................... 15
C.Acid Burns ................................................................. 15
D.Connecting Batteries in Battery Well........................ 15
E. Charging Batteries..................................................... 16
F. Disposing of Batteries................................................ 16
XI. MAINTENANCE......................................................... 17
A.Notes......................................................................... 17
B. Cleaning ..................................................................... 17
C.Storage Tips............................................................... 17
D.Pneumatic Tires......................................................... 17
E. To Repair or Replace a Tire....................................... 17
F. Motor Brushes........................................................... 17
G.Ordering Parts........................................................... 17
H.Maintenance Chart .................................................... 17
TECHNICAL SPECIFICATIONS
XII.
XIII. GUARANTEE (UK ONLY) ........................................ 19
XIV. SUNRISE LIMITED WARRANTY............................ 20
..............................
18
3
101266 Rev. B
ENGLISH
III. YOUR CHAIR AND ITS PARTS
2
3
5
4
QUICKIE/STERLING MELODY
1
6
1. Flip-back armrest
2. Programmable joystick
3. Contour Seat
4. Front caster 6"
5. Single plate foot platform
6. Folding backrest
7. 8" Drive wheels
8
8. Shroud
7
Weight
51 lbs (base)
85 lbs (base + seat)
22 lbs (battery pack)
Drive Wheels
8" Mag: solid tires
Joystick
Standard: P&G VR2
(right-hand or left-hand mount)
Batteries
(2) 12 Amp HR
Battery Charger
Option: off board 2 amp
Colors
Red
Seats, Upholstery and style
High back chair offers semi recline
Material: vinyl
Color: Black
Width: 18"
Depth: 17"
Footrest
Standard: Foot Platform
Casters (front)
Standard: 6" solid
Armrest
Flip-back, 12" arm pad
101266 Rev. B
4
ENGLISH
IV. NOTICE– READ BEFORE USE
A. CHOOSE THE RIGHT CHAIR & SAFETY
OPTIONS
Sunrise provides a choice of many power wheelchair styles, sizes and
adjustments to meet the needs of the rider. However, final selection of a
wheelchair rests solely with you and your health care professional.
Choosing the best chair for you depends on such things as:
1. Your size, disability, strength, balance and coordination.
2. Your intended use, and your level of activity.
3. The types of hazards you must overcome in daily use (in areas where
you are likely to use your chair).
4. The need for options for your safety and comfort (such as positioning belts or special seat systems).
B. ADJUST CHAIR TO YOUR ABILITY
You need to work with your doctor, nurse or therapist, and your supplier,
to fit this chair and adjust the controller settings for your level of function
and ability.
C. REVIEW THIS MANUAL OFTEN
Before using this chair you, and each person who may assist you, should
read this entire Manual and make sure to follow all instructions. Review the
warnings often, until they are second nature to you.
IV. NOTICE– READ BEFORE USE
. WARNINGS
D
The word “WARNING” refers to a hazard or unsafe practice that may
cause severe injury or death to you or to other persons. The “Warnings”
are in four main sections, as follows:
1. V — EMI
Here you will learn about electromagnetic interference and how it can
affect your chair.
2. VI — GENERAL WARNINGS
Here you will find a safety checklist and a summary of risks you need
to be aware of before you ride this chair.
3. VII — WARNINGS — COMPONENTS & OPTIONS
Here you will learn about your chair. Consult your supplier and your
health care professional to help you choose the best set-up and
options for your safety.
4. XI — BATTERIES
Here you will learn about battery and charger safety, and how to
avoid injury.
NOTE– Where they apply, you will also find “Warnings” in other sections of
this Manual.
Heed all warnings to reduce the risk of unintended
brake release or chair movement:
1. Beware of the danger from hand-held transceivers. (A “transceiver” is a device that both sends and receives radio wave
signals). Never turn on or use a hand-held transceiver while
power to your chair is on. Use extra care if you believe that
such a device may be in use near your chair.
2. Be aware of nearby radio or TV stations, and avoid coming
close to them.
If unintended movement occurs, turn your chair off as soon as
3.
it is safe to do so.
WHAT IS EMI?
A.
EMI means: electromagnetic (EM) interference (I). EMI comes from
1.
radio wave sources such as radio transmitters and transceivers.
2. There are a number of sources of intense EMI in your daily environment.
Some of these are obvious and easy to avoid. Others are not, and
you may not be able to avoid them.
3. Powered wheelchairs may be susceptible to electromagnetic interference (EMI) emitted from sources such as radio stations, TV sta
tions, amateur radio (HAM) transmitters, two way radios, and cellu
lar phones.
EMI can also be produced by conducted sources or electro
4.
discharge (ESD).
-static
V. EMI (ELECTROMAGNETIC INTERFERENCE)
B. WHAT EFFECT CAN EMI HAVE?
1. EMI can cause your chair, without warning, to:
• Release its brakes
• Move by itself
• Move in unintended directions
If any of these occurs, it could result in severe injury to you or others.
2. EMI can damage the control system of your chair. This could create a
safety hazard, and lead to costly repairs.
C. SOURCES OF EMI
The sources of EMI fall into three broad types:
1. Hand-Held Transceivers:
The antenna is usually mounted directly on the unit. These include:
• Citizens band (CB) radios
• “Walkie-talkies”
•
•
• Lap-top computers with phone or fax
•
-
-
NOTE– These devices can transmit signals while they are on, even if not in
2. Medium-Range Mobile Transceivers:
These include two-way radios used in police cars, fire trucks, ambulances
and taxi cabs. The antenna is usually mounted on the outside of the vehicle.
, fire and police radios
Security
Cellular phones
Other personal communication devices
use.
ransceivers:
ange T
Long-R
3.
These include commercial radio and TV broadcast antenna towers and
amateur (HAM) radios. Note: The following are not likely to cause EMI
problems: Lap-top computers (without phone or fax), Cordless phones, TV
sets or AM/FM radios, CD or tape players.
5
101266 Rev. B
ENGLISH
. DISTANCE FROM THE SOURCE
D
M energy rapidly becomes more intense as you
E
get closer to the source. For this reason, EMI from
hand-held devices is of special concern. (See C.1
bove) A person using one of these devices can
a
bring high levels of EM energy very close to your
chair without you knowing it.
E. IMMUNITY LEVEL
1. The level of EM energy is measured in volts per meter (V/m). Every
power wheelchair can resist EMI up to a certain level. This is called
its “immunity level”.
2. The higher the immunity level, the less the risk of EMI. It is believed
that a 20 V/m immunity level will protect the power wheelchair user
from the more common sources of radio waves.
3. The Quickie/Sterling Melody with the following configuration was
tested and found to be immune to at least 20 V/m:
Quickie/Sterling Melody power wheelchair with a right-hand mounted Penny & Giles VR2 integral controller, contour seat, flip-back armrests, solid flip-up footplate and battery pack.
Individuals with physical limitations requiring the
use of a specialty control input device known not to
be immune to 20V/m, or not known, should exercise extra care around known sources of EMI.
There is no way to know the effect on EMI if you
add accessories or modify this chair. Any change to
your chair may increase the risk of EMI. Parts from
other suppliers have unknown EMI properties.
F. REPORT ALL SUSPECTED EMI INCIDENTS
You should promptly report any unintended movement or brake release. Be sure to indicate whether
there was a radio wave source near your chair at
the time. Contact: Sunrise Medical Customer
Service Department at (800) 333-4000 or +44 1384
44 66 22.
VI. GENERAL WARNINGS
Heed all warnings in this section. If you fail to do so
a fall, tip-over or loss of control may occur and
cause severe injury to you or others.
A. NOTICE TO RIDER
Before using this chair
1.
health care professional.
2. Every wheelchair is different. Take the time to learn the feel of this
chair before you begin riding.
3. Be aware that you must develop your own methods for the safe use
of this chair that are best suited to your level of function and ability
Have someone help you practice bending, reaching and transferring
4.
until you learn how to do them safely.
Never try a new maneuver on your own unless you are sure it is safe.
5.
Get to know the areas where you plan to use your chair
6.
hazards and learn how to avoid them.
7. Do not allow additional riders on the chair, armrests or chassis.
Doing so may result in injury or damage.
, you should be trained in its safe use by your
. Look for
B. NOTICE TO ATTENDANTS
Make sure you heed all warnings and follow all
instructions in each section of this manual. (Be
aware that warnings that apply to the rider also
apply to you).
2. To manually push the chair you must release the motor locks.
Make sure you have full control over the chair when you release the
motor locks. When you do so the chair will not have brakes.
3. Propel this chair by the armrest supports only.
C. WEIGHT LIMIT
1. Never exceed a total weight of 250 pounds (113.4 kilograms) for rider
plus items carried.
2. Never use this chair for weight training if the total weight (rider plus
additional weights) exceeds 250 pounds (113.4 kilograms).
Exceeding the weight limit is likely to damage the seat, frame, or fas
3.
teners and may cause severe injury to you or others from chair fail
.
ure.
Exceeding the weight limit will void the warranty
4.
.
-
-
D. CONTROLLER SETTINGS
Be aware that you may need to adjust the controller settings of your chair to reduce the risk of a
collision, fall or tip-
Check and adjust the settings every six to twelve months (or more
1.
often, if needed).
2. Consult your supplier to adjust the control settings immediately if
you notice any change in your ability to:
• Control the joystick.
• Hold your torso erect.
Avoid running into objects.
•
over.
Notes:
1. You need to work with the rider and the rider’s doctor, nurse or
therapist, to develop safe methods best suited to your abilities and
those of the rider.
101266 Rev. B
6
ENGLISH
. EMI
E
ead Section V to learn about EMI. To reduce the
R
risk of unintended brake release or chair movement:
. Never turn on or use a hand-held transceiver while power to your
1
chair is on. Use extra care if you believe that such a device may be in
use near your chair.
2. Be aware of nearby radio or TV stations, and avoid coming close to
them.
3. If unintended movement or brake release occurs, turn your chair off
as soon as it is safe.
F. SAFETY CHECK-LIST
Before each use of this chair:
1. Make sure the chair operates smoothly. Check for noise, vibration,
or a change in ease of use. (They may indicate damage to the flatfree inserts, loose fasteners, or other damage to your chair). If you
detect a problem, make sure to repair or adjust the chair. Deferring
repair or adjustment could increase the risk for injury. Your supplier
can help you find and correct the problem.
2. Make sure batteries are charged. Green lights on the controller
charge indicator will light up when charge is full. Yellow lights indicate battery charge level is getting low. Red lights indicate batteries
are in immediate need of charging.
• Never take your chair into a shower, tub, pool or sauna.
• Do not use your chair in fresh or salt water (such as at the edge
of a stream, lake, or ocean).
• Make sure shroud cover and deck lid are secure.
• Replace joystick boot if it becomes torn or cracked.
• Make sure all electrical connections are secure.
• Dry the chair as soon as you can if it gets wet, or if you use
water to clean it.
2. Proceed slowly and use extra care if you must operate your chair on
a wet or slick surface.
• Do so only if you are sure it is safe.
• Stop if one or both main wheels lose traction. If this occurs, you
may lose control of your chair or fall.
• Never operate your chair on a slope or ramp if there is snow,
ice, water or oil film present.
• When in doubt, have someone help you.
3. When not in use, keep your chair in a clean, dry place.
J. TERRAIN
1. This chair is designed for use on firm, even surfaces such as concrete, asphalt and indoor flooring.
2. Do not operate your chair in sand, loose soil or over rough terrain.
Doing so may damage wheels, bearings, axles or motors, or loosen
fasteners.
K. STREET USE
G. CHANGES & ADJUSTMENTS
Never use non-Quickie/Sterling parts or make
changes to your chair unless authorized by Sunrise.
(Doing so will void the Warranty and may create a
safety hazard).
1. If you modify or adjust this chair it may increase the risk of a fall or
tip-over.
2. Modifications unauthorized by Sunrise constitutes remanufacturing of
the wheelchair. This voids the warranty. The rider then assumes all
future liability for the wheelchair.
H. WHEN SEATED IN A PARKED WHEELCHAIR
1. Always turn off all power to your chair when you are parked, even
for a moment. This will prevent:
Accidental movement from contact with the joystick by you or
•
others.
• Unintended brake release or movement from EMI sources. (See
Section V)
Make sure that persons who help you (for example, store clerks) are
2.
aware of the joystick and do not touch it. If they do, your chair may
move suddenly when you do not expect it.
I. ENVIRONMENTAL CONDITIONS
Your chair is not designed for use in a heavy rain
storm, or in snowy or icy conditions.
Contact with water or excessive moisture can cause an electrical mal-
1.
function. The frame, motors and other chair parts are not watertight
and may rust or corrode from the inside. T
• Minimize exposure of your chair to a rain storm or very wet
conditions.
o avoid a chair failure:
In most states, power chairs are not legal for use
on public roads. Be alert to the danger of motor
vehicles on roads or in parking lots.
1. At night, or when it is hard to see, use reflective tape on your chair
and clothing.
2. It may be hard for drivers to see you. Make eye contact with drivers
before you proceed. When in doubt, yield until you are sure it is
safe.
L. MOTOR VEHICLE SAFETY
To date, there is no approved tie down system for
transporting this wheelchair in a motor vehicle.
1. Never sit in this chair while in a moving vehicle. In an accident or
sudden stop you may be thrown from the chair.
• Wheelchair belts are designed to position the rider only
and will not protect you in an accident; further injury may
result from the belts.
2. Always move to an approved vehicle seat. You must be secured with
proper motor vehicle restraints.
Never transport this chair in the front seat of a vehicle. It may shift
3.
and interfere with the driver.
4. Always secure this chair so that it cannot roll or shift.
M. CENTER OF BALANCE
The point where this chair will tip forward, back or
to the side depends on its center of balance and
stability.
The Center Of Balance Is Affected By:
1. The seat height and seat angle.
2. A change in your body position, posture or weight distribution.
Using this chair on a ramp or slope.
3.
7
101266 Rev. B
ENGLISH
4. The use of a back pack or other options, and the amount of added
weight.
To Reduce The Risk Of A Fall Or Tip-Over:
1. Consult your supplier for information on modifications authorized by
Sunrise before you modify or adjust this chair.
NOTE– You may need to make additional changes to correct the center of bal-
ance.
2. Use extreme care until you know the balance points of this chair and
how to avoid a fall or tip-over.
N. TRANSFERS
t is dangerous to transfer on your own. It requires
I
good balance and agility. Be aware that there is a
point during every transfer when the wheelchair
seat is not below you. To avoid a fall:
1. Always turn off power before you transfer to or from your chair. If
you fail to do so you may touch the joystick and cause your chair to
move when you do not expect it.
2. Make sure motor locks are engaged. This keeps the chair from moving when you transfer.
3. Work with your health care professional to learn safe methods.
• Learn how to position your body and how to support yourself
during a transfer.
• Have someone help you until you are sure you can do a safe
transfer on your own.
4. Move your chair as close as you can to the seat you are transferring
to. If possible, use a transfer board.
5. Rotate the front casters until they are as far forward as possible.
6. Be careful of the foot platform. If you can, remove or flip up out of
the way.
• Never stand on footrest when you transfer. Doing so may dam-
age it or cause your chair to tip.
7. Make sure armrests do not interfere.
8. Transfer as far back onto the seat surface as you can. This will reduce
the risk that you will miss the seat or fall.
O. REACHING OR LEANING
Reaching or leaning affects the center of balance of
your chair
likely. When in doubt, ask for help or use a device
to extend your reach.
. If done improperly, a fall or tip-over is
Remember to:
1. Move your chair as close as you can to the object you wish to reach.
2. Rotate the front casters until they are as far forward as possible. This
makes the chair more stable.
NOTE– To do this: Move your chair past the object you want to reach, then
back up alongside it. Backing up will rotate the casters forward.
3. Turn off all power to your chair. If you fail to do so, you may touch
the joystick and cause your chair to move when you do not expect
it.
4. Firmly grasp an armrest with one hand. This will help to prevent a fall
if the chair tips.
P. DRESSING OR CHANGING CLOTHES
Be aware that your weight will shift if you dress or
change clothes while seated in this chair. To make
the chair more stable, rotate the front casters until
they are forward.
Q. OBSTACLES
Obstacles you may have to overcome in daily use
include door thresholds, lifts, ramps and hazards
such as potholes and broken pavement. These can
damage your chair and may cause a fall, tip-over or
loss of control.
1. Be aware that thresholds are very dangerous. (Even a small change in
height may stop a caster wheel and cause your chair to tip). You may
need to:
• Remove or cover threshold strips between rooms.
• Install a ramp at entry or exit doors.
2. Keep your eyes moving when you ride; scan the area well ahead of
your chair.
3. Make sure the floor areas where you use this chair are level and free
of obstacles.
4. To help correct your center of balance:
• Lean your upper body forward slightly as you go up over an
obstacle.
• Press your upper body backward as you go down from a higher
to a lower level.
R. DRIVING IN REVERSE
educe the Risk of injury and/or Damage to the Chair:
o R
T
Never reach or lean if you must shift your weight sideways or rise up
1.
off the seat.
2. Never reach or lean if you must move forward in your seat to do so.
Always keep your buttocks in contact with the backrest.
3. Never reach with both hands (you may not be able to catch yourself
to prevent a fall if you lose your balance).
4. Never try to pick up an object from the floor by reaching down
between your knees.
Never put pressure on the foot platform while reaching. This may
5.
cause the chair to tip if you lean too far.
6. Never reach or lean over the top of the seat back. This may damage
the backrest and cause you to fall.
IF YOU MUST REACH OR LEAN, DO SO AT YOUR
OWN RISK.
101266 Rev. B
Use extra care when you drive your chair in
reverse. You may lose control or fall if one of the
rear wheels hits an object.
1. Operate your chair slowly and at an even speed.
2. Stop often and check to make sure your path is clear of obstacles.
8
ENGLISH
. RAMPS, SLOPES & SIDEHILLS
S
he center of balance of your chair changes when
T
you are on a slope.
NOTE– “Slope” includes a ramp or sidehill. Your chair is less stable when it is
eware Of:
B
at an angle. Never use this chair on a slope unless you are sure it is
safe.
When in doubt, have someone help you.
1. Steep slopes. Do Not use this chair on a slope or incline greater than
7°.
2. Wet or slippery surfaces (such as when ice, snow, water or oil film is
present). A loss of traction may cause a fall or tip-over.
3. A change in grade on a slope (or a lip, bump or depression). These
may cause a fall or tip-over.
4. A drop-off at the bottom of a slope. (A drop-off of as small as 3/4
inch can stop a front caster and cause the chair to tip forward).
T. TO REDUCE THE RISK OF A FALL, TIP-OVER OR
LOSS OF CONTROL
1. Never use your chair on a slope unless you are sure you can do so
without losing traction.
2. Always go as straight up and as straight down as you can.
• Do not “cut the corner” on a slope or ramp.
• Do not turn or change direction on a slope.
3. Always stay in the center of the ramp. Make sure ramp is wide
enough that you are not at risk that a wheel may roll off the side.
4. Lean or press your body uphill. This will help adjust for a change in
the center of balance caused by the slope.
5. Keep your chair moving at a slow, steady speed. Keep control over the
chair at all times.
• On a descent, do not let your chair accelerate beyond its normal
speed.
• If the chair picks up speed, center the joystick to slow down or
stop.
NOTE– The solid state controller of your chair has a logic system that will help
control your speed when driving on a slope or uphill.
• If you stop, re-start slowly.
U. RAMPS AT HOME & WORK
. WHEELCHAIR LIFTS
V
heelchair lifts are used in vans, buses, and build-
W
ings to help you move from one level to another.
. Always turn off all power to your chair when you are on a lift. If you
1
fail to do so, you may touch the joystick by accident and cause your
chair to drive off the platform. (Be aware that a “roll-stop” at the
end of the platform may not prevent this).
2. Make sure there is not a lip or drop-off at the top or bottom of the
platform. These may cause a fall or tip-over. When in doubt, have
someone help you.
3. Always secure the rider with a positioning belt to help prevent falls
during transfers.
4. Avoid moving forward if a wheel is “hung up” on the lip of the ramp.
Backup, reposition the caster for a more direct approach and slowly
try again.
W. CURBS & SINGLE STEPS
1. Your chair is not designed to drive up or down a curb or step more
than one and a half (1.5) inches high. Doing so may:
• Result in a fall or tip-over.
• Damage the frame, wheels, axles or other chair parts, or loosen
fasteners.
2. To prevent a fall or tip-over, use wheelchair access ramps or have
someone help you.
3. If you must climb or descend a curb or step alone do so at your own
risk and use extreme care.
• Go as straight up or straight down as you can. Never turn or
climb or descend at an angle as a fall or tip-over is likely.
• Proceed slowly, at a steady speed.
4. Avoid driving along curb edges and drop-offs. A minimum distance
from the edge of 18” is recommended.
X. STAIRS
Never use this chair to go up or down stairs, even
with an attendant. Doing so is likely to cause a fall
or tip-over.
ESCALATORS
.
Y
Make sure ramps meet all Building Codes for your
area.
For your safety, have a licensed contractor build or remodel ramp to
1.
meet all standards.
NOTE– The proper design will vary, depending on such things as:
2.
the length and height of the ramp; the need for an intermediate platform; landing size; doors and the direction of swing; and whether the
ramp includes a turn or angle.
At A Minimum:
Open sides of ramp must have side rails to prevent your chair from
1.
going over the edge.
2. Slope must not be steeper than one inch in height for every one foot
of slope length.
3. Ramp surface must be even, and have a non-skid surface.
4. You may need to add a section at the top or bottom to avoid a lip or
5. Ramp must be sturdy. Add bracing if needed, so ramp does not
.
off
drop-
“bow” when you ride on it.
Never take this chair on an escalator, even with an
.
attendant. Doing so is likely to cause a fall or tip-
9
over
101266 Rev. B
ENGLISH
VII. WARNINGS: COMPONENTS & OPTIONS
VII. WARNINGS: COMPONENTS & OPTIONS
Note: If you use parts or make changes not author-
zed by Sunrise it may create a safety hazard and
i
will void the Warranty.
A. ARMRESTS
Armrests flip back and cannot be used to lift chair
or the seat.
1. Never lift this chair by its armrests.
2. Lift this chair only by non-detachable parts of the main frame.
B. BATTERIES
1. Only Sunrise authorized batteries should be used in this device.
2. To prevent an acid spill, avoid puncturing the batteries.
3. Never smoke or hold an open flame near batteries. They are a
known
explosion hazard.
4. Read all of section X Batteries before attempting to change or
charge batteries.
5. Always remove batteries using straps or handle provided. Pinched
fingers may occur if the batteries are removed by grasping the battery casings.
• Flip the footplate back.
F. MOTOR LOCKS
1. Do not engage or disengage motor locks unless power to the chair is
off.
2. Be aware that the chair will not have brakes when motor locks are in
the free-wheel position. (See Section F of Operating Guide.)
3. Make sure that the person pushing the chair has full control when
motor locks are disengaged.
G. ON/OFF SWITCH
1. Never use the ON/OFF switch to stop the chair except in an emergency. This will result in an abrupt stop and may cause you to fall.
2. To slow your chair to a stop, return the joystick to neutral, before
turning off the chair.
H. PNEUMATIC TIRES WITH FLAT-FREE INSERTS
1. Do not use this chair if the tires or inserts show any sign of damage.
2. A damaged insert may cause the chair to veer to one side and result in
a loss of control.
3. Driving over sharp objects may cause damage to the tires and/or
inserts.
I. SEATING SYSTEMS
C. CUSHIONS
1. Quickie/Sterling Comfort seats are designed for comfort, not specifically for the relief of pressure.
2. If you suffer from pressure sores, or if you are at risk that they will
occur, you may need a special seat system or a device to control
your posture.
• Consult your doctor, nurse or therapist to find out if you need
such a device for your well-being.
D. FASTENERS
Many of the screws, bolts and nuts on this chair are
special high-strength fasteners. Use of improper
fasteners may cause your chair to fail.
1. Only use fasteners recommended by Sunrise.
2. If fasteners become loose, tighten them as soon as you can.
3. Over- or under-tightened fasteners may fail or cause damage to chair
parts.
• See Section VIII, “Set-Up, Adjustment & Use”, for proper torque
settings.
E. FOOTPLATE
1. At the lowest point, the foot platform should be at least 1.375" off
the ground. If set too LOW, it may “hang up” on obstacles you can
expect to find in normal use. This may cause the chair to stop sud
denly and tip forward.
2. To avoid a trip or fall when you transfer:
• Make sure your feet do not “hang up” or get caught in the space
surrounding the footrest.
• Avoid putting weight on the footplate, as the chair may tip for-
ward.
1. Use of a seating system not approved by Sunrise may alter the center of balance of this chair. This may cause a fall or tip-over.
2. Never change the seating system of your chair unless you consult
your supplier first.
J. UPHOLSTERY FABRIC
1. Replace worn or torn fabric of the seat as soon as you can. If you fail to
do so, the seat may fail and cause you to fall. Worn fabrics may increase
the potential for a fire hazard.
Fabric will deteriorate with age and use. Look for fraying, thin spots,
2.
or stretching of fabric at rivet holes. Replace fabric as required.
3. Be aware that washing may reduce flame retardation of the fabric.
K. WIRING
Never pull on cables directly. This can result in
wires breaking inside the connector or harness. To
remove a plug or connector
or connector itself.
-
, always grasp the plug
101266 Rev. B
10
ENGLISH
VIII. SET-UP, ADJUSTMENT & USE
VIII. SET-UP, ADJUSTMENT & USE
NOTES:
1. Work Surface For Set-Up:
Use a flat surface, such as a table, to assemble, adjust and check your chair. This makes the steps easier
and helps ensure a correct set-up.
. Fasteners:
2
• Many of the screws and bolts on this chair are special high-strength fasteners and may have special
coatings.
• Many nuts are of the Nylock type. They have a plastic insert to help prevent loosening.
1. Use of improper fasteners may cause the chair to fail.
2. Over- or under-tightened fasteners may fail or cause damage to chair parts.
3. If bolts or screws become loose, tighten them as soon as you can. Loose bolts or screws
can cause damage to other chair parts causing them to fail.
3. Washers & Spacers:
• Note the position of washers and spacers before disassembly.
• To avoid damage to the frame, replace all washers and spacers when you reassemble parts.
4. Torque Settings:
• A torque setting is the optimal tightening for a particular fastener. Use a torque wrench that
measures 120 inch-pounds to secure screws, nuts and bolts on this chair.
NOTE– Unless otherwise noted, use a torque setting of 120 inch-pounds for all fasteners.
TOOLS YOU WILL NEED
1. Basic Tool Kit:
To set-up, adjust and maintain your chair you will need the following tools:
• 5mm Allen Wrench
• 6mm Allen Wrench
• 8 mm Open-end Wrench
• 10 mm Open-end Wrench
• 13mm Open-end Wrench
• 17mm Open-end Wrench
• Phillips screwdriver #2
• 13mm Socket Wrench
You can obtain a multi-purpose tool kit from Sunrise, or buy the tools you need from a hardware store.
2. Torque Wrench:
If you plan to adjust and maintain this chair yourself, Sunrise recommends that you use a torque wrench.
NOTE– The wrench must measure inch-pounds. You can buy a torque wrench and proper sockets from a
hardware store.
CHECK-OUT
Be sure this chair performs to your chosen operational settings. If it does not, turn the chair off immediately and have your supplier reprogram your wheelchair as needed
NOTE– Repeat this procedure until the chair performs to your specifications.
When properly set up, this chair will operate smoothly. Check to see that
all components work properly. If you detect a problem, be sure to correct
it before use.
11
101266 Rev. B
ENGLISH
A. BATTERY CASE REMOVAL
To remove the batteries for transporting or servicing:
1
1. Remove Battery Case
a. To remove battery pack, lift up on battery pack handle (A).
2. Battery Installation
See Section X. Batteries, D for installation.
atteries may weigh up to 25 lbs. Care must be taken to avoid injury when
B
lifting up on battery handle.
B. ARMRESTS ADJUSTMENT
1. Width Adjustment
a. Insert armrest support inside of 1" square tube located on back of the seat.
b. Repeat for other side of seat.
c. Position armrest at appropriate width.
Tighten knob screws (B) on square tube.
d.
Avoid pinching fingers in the flip-back armrest.
2
C. SEAT REMOVAL
1. Unplug the controller connections at the back of the seat.
2. Lift the chair straight up off of the seat mount.
3. When replacing the seat onto the mount, make sure the seat is aligned properly and does not
swivel before sitting.
1
A
2
B
Keep hands away from the seat post when replacing the seat to ensure
you do not pinch your fingers.
101266 Rev. B
12
ENGLISH
IX. OPERATING GUIDE
A. PERFORMANCE CONTROL SETTINGS
1. It is vital to match control settings to your level of function and ability.
2. Consult your health care professional and your supplier to select the best control settings for you.
3. Check and adjust the settings every six to twelve months (or more often, if needed).
4. Adjust the control settings immediately if you notice any change in your ability to:
• Control the joystick.
• Hold your torso erect.
• Avoid running into objects.
5. Control Settings are adjusted through the use of the Sunrise Medical Programming Pad. See your
supplier.
B. SUNRISE MEDICAL PROGRAMMER PAD
Program settings beyond the ability of the rider can result in serious injury.
Consult your health care advisor before you alter settings.
1. Notes:
The Sunrise Medical Programmer lets you adjust the performance control settings of the Melody. You
can customize a program for yourself or select the standard program.
• acceleration rate
• deceleration rate
• turn acceleration
• turn deceleration
• forward speed (max & min)
• reverse speed (max & min)
• turn speed (max & min)
• steer correct
Remote systems
• 4-axis joystick throw
• sleep timer
• profile number
• read timer
2. To Program Your Chair:
a. Turn off power to the chair.
b. Insert Sunrise Medical Programmer plug (A) into the programmer/charger socket on the front of
the joystick.
urn on power to the chair; program as needed.
c. T
emove plug and cycle ON/OFF switch to drive chair
R
d.
NOTE– Review the Sunrise Medical P
NOTE– P
.
chair
rogram settings that are not matched for the capabilities of the rider can result in serious injury
not alter settings without the advice of your health care professional.
rogrammer Owner
.
’s Manual for more details on how to program your
IX. OPERATING GUIDE
A
. Do
THERMAL ROLL-BACK
C.
Your chair has a thermal roll back circuit. This protects the controller from damage due to overheating.
In extreme conditions (such as repetitive hill climbing) the circuit will decrease the power to your
motors. This allows the chair to operate at a reduced speed. When the controller cools, the chair will
return to normal speed.
13
101266 Rev. B
ENGLISH
D. CIRCUIT BREAKERS
1
1. Notes:
Your Quickie/Sterling Melody has a circuit breaker on the battery case.
• In the unlikely event of a short circuit or heavy overload, all power to your chair will be shut off.
To reset your chair, depress the circuit breaker button located at the rear corner of the chair. A
•
few minutes wait is required before the circuit breaker will reset.
2. Repeated Shutdown:
If the chair continues to shut down after resetting, have it serviced by a supplier.
E. JOYSTICK ASSEMBLY
The standard VR2 joystick controls the chair’s performance. It consists of the following parts:
2
1. Speed Control or Drive Mode Selection Buttons (A and B)
To decrease the speed level depress button A. Or, when 1- 5 Drive modes are programmed, depress
button A to activate lower drive mode(s).
To increase speed level, depress button B. Or, when 1- 5 Drive modes are programmed, depress button
B to activate higher drive mode(s).
Speed level active, or Drive Mode selected, is indicated on display (C) by a series of five lights. One light
indicates slowest level/mode currently active, while five lights indicates highest level/mode currently
active.
2. Battery Charge Indicator (D)
• Green lights indicate that batteries are fully charged.
• Yellow lights indicate that batteries need recharging.
• When the lights stay in the red band, the batteries must be recharged.
3. On/Off Button (E)
Turning the chair on or off is accomplished by depressing button E.
1
Circuit breaker
2
D
E
F
C
AB
4. Horn (F)
5. Joystick (G)
The joystick controls the direction and speed of your chair. Turn the chair on and move the joystick in
the direction you want to go.
• Moving the joystick from the neutral (center) position disengages the motor locks, allowing the
chair to move.
The chair will move faster the more you move the joystick away from neutral.
•
NOTE– If your speed becomes hard to manage, release the Joystick and the chair will come to a complete
NOTE– Once the chair stops, switching the chair off will not affect the motor locks.
6.
Make sure the boot is not torn or cracked (this could allow debris, water or moisture to enter). If the
boot is torn or cracked, replace it as soon as you can.
F. MOTOR LOCK
Disconnect the motor lock when you need to manually push the chair
(For example, in an emergency, or if batteries fail).
stop.
• When you release the joystick it will return to neutral; the chair will slow to a stop and the motor
locks will reengage.
• We recommend that you switch the chair off if you stop for any length of time. This will conserve
battery power.
Joystick Boot (H)
3
.
1. Do not disengage motor lock unless power to the chair is off.
2. With the brake released, the chair will not operate and the battery charge indicator will
flash 9 bars rapidly (if power to the chair is on.)
3. Be aware that the chair will not have brakes in the free-wheel position.
Make sure that the person pushing the chair has full control when motor locks are
4.
disengaged.
H
G
3
Motor Lock
101266 Rev. B
14
ENGLISH
X. BATTERIES
X. BATTERIES
A. INTRODUCTION
1. Notes:
• Batteries supply the power for your chair. They contain a finite
amount of energy and have limits on how long they can store and
supply energy.
• You can charge batteries only a certain number of times before they
will fail and no longer hold a charge.
• For answers to questions about batteries, consult your supplier.
. Use Proper Battery Case:
2
Your chair operates on a 12A battery pack.
• Only use an authorized Sunrise battery pack.
3. Breaking In:
• A battery requires “breaking-in” for the first 6 to 12 charges. It will
not accept a full charge for this period.
• It is best to limit the length of your trips until you break the batteries
in and you know the range of your chair.
4. Discharged Batteries:
• Never allow a battery to completely discharge. If you operate your
wheelchair until it has almost stopped, you will greatly reduce the life
of your batteries.
Never let a battery sit in a discharged condition. Give unused or
•
stored batteries a full charge once per month.
• Always fully charge the batteries. Avoid “topping off” with
frequent charges.
Never connect a life support or auxiliary device to a
wheelchair battery. The electrical system may fail
and result in severe injury to or death of rider.
3. CAUTION– To Avoid Damage to the Battery
• Make sure you use the correct setting for sealed (gel) batteries
(located on the off-board charger) if applicable.
•
Never charge a frozen battery. A fully charged battery will rarely
freeze, but the fluid in a discharged battery can freeze at 16 degrees
Fahrenheit (minus 9 degrees Centigrade). If you suspect a battery is
frozen, thaw it before charging.
Lead acid batteries generate explosive gas while
charging. Completely read and follow all warnings
bout the batteries in this user instruction manual
a
and any labels applied to the product. Failure to do
so could result in fire, explosion, injury and/or death.
C. ACID BURNS (SEALED LEAD ACID BATTERIES)
Acid in batteries is corrosive. If the battery pack is damaged or punctured,
the acid inside can cause serious burns to the eyes and skin and can damage
floors, furniture, clothing and your wheelchair.
1. Use extreme care not to damage the battery pack when
operating your chair or transporting the battery pack.
2. If battery should leak due to dammage, avoid contact of acid
with bare skin or clothing.
3. If acid contacts your skin or clothing, wash immediately with
soap and water.
4. If acid contacts your eyes, immediately flood eyes with cold
running water for at least 15 minutes. Seek medical attention
immediately.
D. CONNECTING BATTERIES IN BATTERY PACK
B. BATTERY CHARGER
A battery charger produces a direct current (DC). When applied to a discharged battery, this reverses the chemical reaction that led to its discharge.
1. Charge Rate. How fast a battery will charge depends on:
• Its electrical capacity
internal condition.
• The DC output of the charger. (The charge rate will vary if the alternating current (AC) supply is higher or lower than 110 volts (or 230V
in Europe)).
CAUTION–
2.
• Never expose charger to rain or snow
• Never unplug charger by pulling on the electrical cord. This will
damage the cord.
• Never open a charger or attempt to repair it yourself. Return charger to Sunrise or have repairs made only by a qualified person.
eep cord out of the way, where it will not be stepped on, tripped
K
•
over, or damaged.
, state of charge, electrolyte temperature, and
void Damage to the Charger
o A
T
.
1. Each battery weighs up to 25 lbs. Take care to avoid injury
when lifting.
2. Before working around batteries, remove all metal personal
effects, such as necklaces, rings, watches, pins, and other
metal jewelry that might contact battery terminal and cause
a short.
Never make direct contact across both battery ter
minals, as an explosion may occur. A spark may
result in an explosion and/or fire resulting in severe
injury or death.
-
15
101266 Rev. B
ENGLISH
E. CHARGING BATTERIES
21
To avoid the risk of severe injury or death from electrical shock, fire or
xplosion while charging:
e
1. Ensure the charger is connected to the correct source (110V or (230V in Europe)).
2. Never touch the charger after it is connected to an electrical outlet. This may cause electrical
shock.
• Never connect or disconnect charger from battery while there is power to the charger.
3. Never use an extension cord. Use of an improper cord could damage the charger or cause a fire
or electrical shock.
4. A battery emits explosive hydrogen gas during charging. To reduce the risk of fire or explosion:
• Make sure area is well vented. Never charge battery in a closed-in area.
• Never smoke or allow a spark, flame or high heat near battery during charging.
• Never allow metal tools or chair parts to make direct contact across both battery terminals.
ALWAYS:
1. Use the charger that comes with your wheelchair. Read and follow all instructions and warnings.
2. Make sure room is well ventilated.
3. Turn off all power to your chair.
4. Connect and disconnect battery cables with caution.
5. Make sure to allow enough time to fully charge batteries.
NOTE– Batteries should never be left for long periods in the discharged state. Unused or stored batteries
should be given a charge once per month.
6. Use the off-board charger by plugging it into the VR2 controller or by plugging it into the charger
port on the top side of the battery case.
1
Controller port
(located under controller)
2
F. DISPOSING OF BATTERIES
1. All batteries once they have reached the end of their useful life are deemed to be hazardous
waste.
2. For further information on handling and recycling contact your local
recycling authority.
3. Always dispose of product through a recognized agent.
Charger Port
101266 Rev. B
16
ENGLISH
XI. MAINTENANCE
A. NOTES
1. Proper maintenance will improve performance and extend the useful
life of your chair.
2. Clean your chair regularly. This will help you find loose or worn parts
and will make your chair easier to use.
3. To protect your investment, have all major service and repair work
done by your supplier.
1. Your chair needs regular maintenance for peak performance
and to avoid injury from chair failure, damage or premature
wear.
2. Inspect and maintain this chair strictly per the “Maintenance
Chart”.
3. If you detect a problem, make sure to service or repair the
chair before use.
4. At least once a year, have a complete safety check and service
of your chair performed by a supplier.
B. CLEANING
1. Plastic Shroud Cover:
• Clean the plastic finish with mild soapy water monthly.
2. Motors:
• Clean around motor area weekly with a slightly damp (not wet)
cloth.
• Wipe off or blow away any fluff, dust, or dirt on or around the
motors.
• Note: You do not need to grease or oil the chair.
3. Upholstery:
• Hand-wash only as needed. Machine washing may damage fabric.
• Drip-dry only. Heat from a dryer may damage fabric.
NOTE– Washing the fabric may decrease fire retardant properties.
C. STORAGE TIPS
1. Store your chair in a clean, dry area. If you fail to do so, parts may
rust or corrode.
2. Before using your chair, make sure it is in proper working order.
Inspect and service all items on the “Maintenance Chart”.
3. If you store this chair for more than three months, have it inspected
by a supplier before use.
D. PNEUMATIC TIRES (IF APPLICABLE)
XI. MAINTENANCE
. TO REPAIR OR REPLACE A TIRE
E
rive Wheels:
D
a. Elevate and securely support chair so that wheel is off the ground.
b. Remove hub cap.
c. Remove lock bolt.
d. Replace wheel. (Make sure washers and shaft key are in the same
location.)
e. Install lock bolt.
f. Install hub cap.
F. MOTOR BRUSHES
Check the motor brushes every four (4) months for wear. The brushes
should be clean and shiny. Replace worn or blackened brushes.
G. ORDERING PARTS
When you order parts, provide the following:
1. Model of chair
2. Serial number of chair
3. Left hand or right hand control
4. Part number, description and quantity of parts you need.
5. State reason for replacement.
H. MAINTENANCE CHART
You should check the items on this chart at the indicated intervals. If any of
the items are loose, worn, bent or distorted, immediately have them
checked and/or repaired by your authorized Sunrise supplier. Frequent
maintenance and servicing will improve performance and extend wheelchair
life, and help prevent injuries.
Daily
Weekly
Monthly
Quarterly
✓ Charge batteries
✓ Check tires for damage
✓
✓ Check all moving parts for wear
✓
✓ Inspect upholstery for wear
Check...
Annually
Check plugs and connectors for proper
connections
Inspect all nuts, bolts and fasteners
for looseness or wear
1. Do not use this chair if any of the tires show signs of damage.
2. A damaged insert may cause the chair to veer to one side and
result in loss
Check for signs of wear on your tires weekly.
control.
of
17
✓ Remove and inspect motor brushes
✓ Service by authorized supplier
101266 Rev. B
Loading...