Sunrise Medical Quickie Pulse 6BC, 5CC, 6SC, 6MPC, 6CC Owner's Manual
...
SECTION
Quickie®Pulse
6BC, 6SC, 6CC, 5BC, 5CC, 6MPC
Supplier:
User:
This manual must be given to the rider of
this wheelchair.
Before using this wheelchair read this entire manual and save
for future reference.
Quickie®Pulse
6BC, 6SC, 6CC, 5BC, 5CC, 6MPC
ENG L ISH
PULSE
O w n e r ’ s M a n u a l
Distribuidor:
Pasajero:
Cada una de las sillas se envía con un manual de instrucciones en inglés. El manual en español
o francés está disponible en formato PDF en nuestra página en Internet:
www.SunriseMedical.com. Ingrese a la página del producto específico para descargar el manual, o comuníquese con el proveedor autorizado de Sunrise Medical.
Este manual debe ser entregado al pasajero de esta silla de
ruedas.
Antes de usar esta silla de ruedas, lea este manual en su
totalidad y guárdelo para futura referencia.
Quickie®Pulse
6BC, 6SC, 6CC, 5BC, 5CC, 6MPC
Fournisseur:
Utilisateur / Utilisatrice:
Chaque fauteuil est livré avec un manuel d’instructions en anglais. Les versions en espagnol et
en francais sont à ançais est à votre disposition en format PDF sur le site:
www.SunriseMedical.com. Veuillez vous rendre à la page de votre produit pour télécharger
le manuel dans la langue souhaitée, ou contactez un fournisseur agréé Sunrise Medical.
Ce manuel doit être remis à l’utilisateur / utilisatrice de ce
fauteuil roulant.
Avant d’utiliser ce fauteuil roulant, lisez entièrement ce manuel et conservez le pour le consulter ultérieurement.
M a n u a l d e I n s t r u c c i o n e s
M o d e d ’ e m p l o i
QUI CK IE PU LS E
I. INTRODUCTION
SUNRISE LISTENS
Thank you for choosing a Quickie wheelchair. We want to hear
your questions or comments about this manual, the safety and
reliability of your chair, and the service you receive from your
Sunrise supplier. Please feel free to write or call us at the address
and telephone number below:
Sunrise Medical (US) LLC
ustomer Service Department
C
2842 Business Park Ave
Fresno, CA 93727
(800) 333-4000
FOR ANSWERS TO YOUR QUESTIONS
Your authorized supplier knows your wheelchair best, and can
answer most of your questions about chair safety, use and maintenance. For future reference, fill in the following:
upplier: _______________________________________________________________
S
Address: _______________________________________________________________
______________________________________________________________________
USER WARNING
WARNING
Attention wheelchair users, do not operate this wheelchair without first reading the owner’s manual. If you do not understand the
instructions and warnings of this owner’s manual please contact
your dealer or qualified technician before operating this Quickie
wheelchair. Failure to do so may result in damage and/or injury.
DEALER/TECHNICIAN WARNING
WARNING
Attention dealers and qualified technicians, do not operate or service this wheelchair without first reading this owners manual. If you
do not understand the instructions and warnings of this owners
manual please contact the Quickie Technical Service Department
before operating and/or servicing this Quickie wheelchair. Failure
to do so may result in damage and/or injury.
ELECTROSTATIC DISCHARGE
WARNING
Telephone: _____________________________________________________________
Serial #: _________________________________________ Date/Purchased:_________
INFORMATION YOU SHOULD KNOW
No component of this chair was made with Natural Rubber Latex.
DISPOSAL AND RECYCLING INFORMATION
When this product reaches the end of its life, please take it to an
approved collection or recycling point designated by your local or
state government. This wheelchair is manufactured using a variety
of materials. Your product should not be disposed of as ordinary
household waste. You should dispose of your wheelchair properly, according to local laws and regulations. Most materials that are
used in the construction of this product are fully recyclable. The
separate collection and recycling of your product at the time of
disposal will help conserve natural resources and ensure that it is
disposed in a manner that protects the environment.
Ensure you are the legal owner of the product prior to arranging
for the product disposal in accordance with the above recommendations.
Power wheelchairs have printed circuit boards. Careful attention
should be given to printed circuit board handling techniques to
avoid damaging the control, and/or drive electronics of the chair,
this could create a safety hazard. Do not expose or remove printed circuit boards. Contact your Authorized Dealer for help with
any electronics issues.
Related Documents
Listed below are additional documents which are referenced in
this owners manual.
• RNET Owners Manual:
PG Drives Technology CJSM2 Installation manual
• RNET OBP Owners Manual
• RNET Omni Owners Manual
• PULSE Service Manual
119832Rev. G
2
QUI CK IE PU LS E
II. TABLE OF CONTENTS
I.INTRODUCTION .....................................................................................2
III. YOUR CHAIR AND ITS PARTS ................................................4
IV. NOTICE– READ BEFORE USE...................................................5
V. EMI (ELECTROMAGNETIC INTERFERENCE).......................5
A.What is EMI?................................................................................5
B. What effect can EMI have?.......................................................5
C.Sources of EMI ........................................................................5-6
D.Distance from the Source ........................................................6
E. Immunity Level ............................................................................6
F. Report all Suspected EMI Incidents........................................6
G.EMI from Chair ...........................................................................6
H.Head Array Safety and RFI.......................................................6
VI. GENERAL WARNINGS................................................................7
A.Notice to User and Attendants..............................................7
B. Weight Limit................................................................................7
C.Controller Settings.....................................................................7
D.Safety Checklist ...........................................................................7
E. Changes and Adjustments ........................................................7
F. Accessories ..................................................................................7
G.When Seated in a Parked Wheelchair ..................................8
H.Environmental Conditions........................................................8
I. Terrain ..........................................................................................8
J. Street Use ....................................................................................8
K. Motor Vehicle Safety .................................................................8
L. Center of Balance.......................................................................8
M. Transfers .....................................................................................9
N.Reaching or Leaning ...................................................................9
O.Dressing or Changing Clothes................................................9
P. Obstacles......................................................................................9
Q.Driving in Reverse......................................................................9
R. Ramps, Slopes, and Sidehills.....................................................9
S. Reduce the Risk of a Fall, Tip-over or Loss of Control ..10
T. Ramps at Home and Work ...................................................10
U.Wheel Chair Lifts .....................................................................10
V. Curbs and Single Steps............................................................10
W. Stairs .........................................................................................10
X.Escalators ...................................................................................10
VII. WARNINGS: COMPONENTS AND OPTIONS.................11
A.Armrests.....................................................................................11
B. Batteries .....................................................................................11
C.Cushions and Sling Seats ........................................................11
D.Fasteners ....................................................................................11
E. Footplate, and Footrests ........................................................11
F. Motor Locks ..............................................................................11
G.ON/OFF Switch ........................................................................11
H.Pneumatic Tires........................................................................11
I. Positioning Belts .......................................................................11
J. Push Handles .............................................................................12
K. Seating Systems.........................................................................12
L. Upholstery Fabric.....................................................................12
M.Suspension..................................................................................12
N.Wiring .........................................................................................12
O.Assignable Controls.................................................................12
P. Power Seating (SC & MPC) ...................................................12
Q. S.P.O.T. Power Accessory...................................................12
R. Power Recline ...........................................................................13
S. Power Legrest Accessory ......................................................13
T. Transit Option and Use....................................................13-16
VIII. USE AND MAINTENANCE ......................................................17
A.Introduction...............................................................................17
B. Cleaning......................................................................................17
C.Storage Tips...............................................................................17
D.Tire Pressure.............................................................................17
E. Motor Brushes ..........................................................................17
F. Disposing of Batteries .............................................................17
G Ordering Parts ..........................................................................17
H.Safety Checklist.........................................................................17
I. Folding Backrest .......................................................................18
J. Manual Recline Operation ....................................................18
K. Swing-in/Swing-out Footrests................................................18
L. Elevating Legrest.......................................................................18
M.Angle Adjustable Centermount Footrest...........................18
N.Dual-post Fixed height standard, and Dual-post Height
O. Single-post Height Adjustable Armrests ...........................19
P. Retractable, Swing-away, and Midline Joystick Mounts...19
Q Motor Lock................................................................................20
R. Battery Removal .......................................................................20
S. Captain’s Seat ............................................................................20
T. Check Out .................................................................................21
IX. CONTROLLER, JOYSTICKS & OPERATING GUIDE .......22
A.Controls .....................................................................................22
B. Connectors................................................................................22
C.R-NET Joysticks........................................................................22
D.Joystick Buttons and Controls .............................................23
E. LCD Screen (Color and advanced) .....................................24
F. Performance Control Settings ..............................................26
G.On-Board Programmer, Diagnostic Test Tool, or RNET ..
H.Control +5 assignable buttons..............................................26
I. Joystick Stationary ..................................................................26
J. Thermal Roll-Back....................................................................26
K. Recline, Tilt & Lift Operation................................................26
L. VR2 Joystick...............................................................................27
X. BATTERIES.....................................................................................28
A.Introduction .............................................................................28
B. Charging Batteries ..................................................................28
C.Battery Charger........................................................................28
D.Connecting Batteries .............................................................29
E. Battery Maintenance................................................................29
F. Disposing of Batteries .............................................................29
G.Fuses............................................................................................29
H.Battery Wiring Diagram .........................................................29
XI. DEALER SERVICE AND ADJUSTMENT................................30
A.Dealer Service Introduction .................................................30
B. Critical Maintenance Tips .....................................................30
C. Cleaning ....................................................................................30
D. Adjustment Notes ..................................................................30
E. Shroud Removal .......................................................................31
F. Battery Removal .......................................................................31
G.Single-post Height-adjustable Armrests..............................31
H.Cantilever Armrests................................................................32
I. Retractable Joystick Mount....................................................32
J. Midline Joystick Mount............................................................32
K. Joystick Controller Position ..................................................33
L. Swing-in/out Footrest Adjustment .......................................33
M.Angle Adjustable Center Mount Footrest ........................33
N.Elevating Legrest Adjustment ................................................33
O.Center Mount Hanger Adjustment .....................................34
P. Power Center Mount Footrest ASAP ................................34
Q.Power Center Mount Footrest Recline .............................34
R. Fixed Center Mount Footrest (Power Recline) ...............34
S. Seat Depth Adjustment .........................................................35
T. Seat Removal .............................................................................35
U.Seat Pan and Back Size Adjustments ...................................35
V. Seat Height Adjustment..........................................................36
W.Seat to Floor Height/pre-tilt Positioning ...........................36
X.Captains Seat.............................................................................37
Y. Controller Position..................................................................38
Z. Repair or Replace a Tire ........................................................38
XII. SUNRISE LIMITED WARRANTY.............................................39
APPENDIX .....................................................................................40
ESPAÑOL .......................................................................................45
FRANÇAIS......................................................................................83
Adjustable Armrests ..............................................................19
PC Programmer (Option) ......................................................26
3
119832 Rev. G
QUI CK IE PU LS E
3
9
III. YOUR CHAIR AND ITS PARTS
III. YOUR CHAIR AND ITS PARTS
1. Flip-back, height adjustable armrest
2. VR2 controller joystick (RNET option)
3. Captain’s seat
4. Front Caster 7”
2
1
8
5. Rear stabilizing caster 6”
6. Single plate foot platform (shown)
Optional:
Swing-away 65° hangers
Swing-away ELR hangers
Swing-away 70° hangers
Swing-away 75° hangers (tapered)
Swing-away 90° hangers
7. Drive wheels
8. Brake release
9. Caster fork (front)
10. Caster fork (rear)
11. Front shroud
10
4
6
Weight (lbs)
Chair with Batteries
SC -260, BC -235, CC -250, MPC -350
Chair without Batteries
SC -182, BC -157, CC -172, MPC -272
Drive Wheels
13" Mag: Std. airless insert
Joystick
Option - VR2 - Right or left handed,
assembly, actuator control.
Option - RNET - (LED,Color)
Option Joystick Advanced - Color dis-
play, paddle switches, Infrared
Output, programmable buttons,
Stereo Jacks.
Batteries
(2 deep cycle batteries required to
operate chair)
Standard - Group 22
Battery Charger
Off board 8 AMP
11
7
QUICKIE PULSE
Shroud Colors
Red, Black, Blue, Silver, Copper, Green
Apple, Yellow, Pearl Pink, Candy
Purple, Matte Black, Midnight Blue,
Pearl white, Digital camo, Woodland
Camo, Carbon fiber print.
Seats, Upholstery and Style
Standard- BC & SC: A.S.A.P. II Seat Frame
CC: Captain’s Seat
Sizes: 12" - 22" wide, 12" - 22" deep
MPC: 14" - 22" wide, 16” -20” deep
Footrest:
CC: Center Mount SC & BC: Standard-
SA Swing away footrests w/heel loops
Option-Foot platform, Manual elevating legrests, Power Articulating
Legrest (ALR), Power Center Mount,
Center mount
Backrest
SC & BC: Standard Canes Angle Adjust
Option- 8° Bend, Semi Recline,
Folding
CC: standard- Captain’s Seat Back
MPC: Recline
5
Models
Pulse 6 BC, SC, and CC (shown)
Pulse 5 BC,CC
Pulse 6 MPC
Casters front
Standard- 7” solid
Casters rear
Standard- 6” solid
Armrest
SC & BC: Standard- 14" Cantilever,
height adjustable 14" arm pad
Option- Locking, two-point arm,
Dual post Arm, Single Post arm
MPC: Reclining/Otto Bock
Suspension
Standard- all wheel
All features may not be available with some chair
setups or in conjunction with another chair feature.
Please consult your supplier for more information.
Your authorized supplier can also provide you with
more information on accessories.
119832Rev. G
4
QUI CK IE PU LS E
IV. NOTICE– READ BEFORE USE
A. CHOOSE THE RIGHT CHAIR & SAFETY
OPTIONS
Sunrise provides a choice of many power wheelchair styles, sizes
and adjustments to meet the needs of the user. However, final
selection of a wheelchair rests solely with you and your health care
professional. Choosing the best chair for you depends on such
hings as:
t
1. Your size, disability, strength, balance and coordination.
2. Your intended use, and your level of activity.
3. The types of hazards you must overcome in daily use (in
areas where you are likely to use your chair).
4. The need for options for your safety and comfort (such as
positioning belts or special seat systems).
INTENDED USE:
with wheels that is intended for medical purposes to provide
mobility to persons restricted to a sitting position.
The Quickie PULSE is a battery operated device
B. ADJUST CHAIR TO YOUR ABILITY
You need to work with your doctor, nurse or therapist, and your
supplier, to fit this chair and adjust the controller settings for your
level of function and ability.
C. REVIEW THIS MANUAL OFTEN
Before using this chair you, and each person who may assist you,
should read this entire Manual and make sure to follow all instructions. Review the warnings often, until they are second nature to
you.
D. WARNINGS
The word “WARNING” refers to a hazard or unsafe practice that
may cause severe injury or death to you or to other persons. The
“Warnings” are in four main sections, as follows:
1. V — EMI
Here you will learn about electromagnetic interference and
how it can affect your chair.
2. VI — GENERAL WARNINGS
Here you will find a safety checklist and a summary of risks
you need to be aware of before you ride this chair.
3. VII — WARNINGS — COMPONENTS & OPTIONS
Here you will learn about your chair. Consult your supplier
and your health care professional to help you choose the
best set-up and options for your safety.
4. X — BATTERIES
Here you will learn about battery and charger safety, and
how to avoid injury.
Throughout this owner’s manual and on the wheelchair you will
see the icons listed below to identify warnings and potential hazards.
WARNING!
ESD:
Electrostatic Discharge can damage printed
These warnings must be followed, failure to
do so may cause personal injury or may damage the wheelchair.
circuit boards.
WARNING
Heed all warnings to reduce the risk of unintended brake release
or chair movement:
1. Beware of the danger from hand-held transceivers. Never
turn on or use a hand-held transceiver while power to your
chair is on. Use extra care if you believe that such a device
may be in use near your chair.
2. Be aware of nearby radio or TV stations, and avoid coming
close to them.
3. If unintended movement occurs, turn your chair off as soon
as it is safe to do so.
A. WHAT IS EMI?
WARNING
1. EMI means: electromagnetic (EM) interference (I). EMI
comes from radio wave sources such as radio transmitters
and transceivers. (A “transceiver” is a device that both sends
and receives radio wave signals).
2. There are a number of sources of intense EMI in your daily
environment. Some of these are obvious and easy to avoid.
Others are not, and you may not be able to avoid them.
3. Powered wheelchairs may be susceptible to electromagnetic
interference (EMI) emitted from sources such as radio stations, TV stations, amateur radio (HAM) transmitters, two
way radios, and cellular phones.
4. EMI can also be produced by conducted sources or electrostatic discharge (ESD).
V. EMI (ELECTROMAGNETIC INTERFERENCE)
B. WHAT EFFECT CAN EMI HAVE?
WARNING
1. EMI can cause your chair, without warning, to:
• Release its brakes
• Move by itself
• Move in unintended directions
If any of these occur, it could result in severe injury to you
or others.
2. EMI can damage the control system of your chair. This could
create a safety hazard, and lead to costly repairs.
3. EMI can cause Bluetooth connection, and/or mouse interference.
C. SOURCES OF EMI
WARNING
The sources of EMI fall into four broad types:
1. Hand-Held Transceivers:
The antenna is usually mounted directly on the unit. These include:
• Citizens band (CB) radios
• “Walkie-talkies”
• Security, fire and police radios
• Mobile phones
• Lap-top computers with phone or fax
• Other personal communication devices
NOTE –
2. Wireless Routers
These devices can transmit signals while they are on, even if not
in use.
5
119832 Rev. G
QUI CK IE PU LS E
3. Medium-Range Mobile Transceivers:
These include two-way radios used in police cars, fire trucks,
ambulances and taxi cabs. The antenna is usually mounted on the
outside of the vehicle.
4. Long-Range Transceivers:
These include commercial radio and TV broadcast antenna towers
and amateur (HAM) radios.
NOTE–
top computers (without phone or fax), Cordless phones, TV sets
or AM/FM radios, CD or tape players.
The following are not likely to cause EMI problems: Lap-
D. DISTANCE FROM THE SOURCE
WARNING
Electro-magnetic energy rapidly becomes more intense as you get
closer to the source. For this reason, EMI from hand-held devices
is of special concern.
these devices can bring high levels of EM energy very close to your
chair without you knowing it.
CAUTION -
ference or loss of connection if the wheelchair is within 1 meter
of a wireless router.
For additional detail regarding the recommended separation distance between radio frequency communication equipment and this
product, see Appendix Table 4 (Recommended separation distance
between portable and mobile RF communications equipment and
the product)
If using Bluetooth, the user might experience inter-
(See Section C.1)
A person using one of
V. EMI (ELECTROMAGNETIC INTERFERENCE)
WARNING
There is no way to know the effect on EMI if you add accessories
or modify this chair. Any change to your chair may increase the
risk of EMI. Parts not specifically tested or parts from other suppliers have unknown EMI properties. For additional detail regarding
the testing and use of this product with respect to electromagnetic
immunity, see Appendix, Tables 2 and 3 (Guidance and manufacturers declaration - electromagnetic Immunity)
F. REPORT ALL SUSPECTED EMI
INCIDENTS
WARNING
You should promptly report any unintended movement or brake
release. Be sure to indicate whether there was a radio wave
source near your chair at the time. Contact:
Sunrise Medical, Customer Service Department at (800) 333-4000.
G. EMI FROM CHAIR
WARNING
The chair itself can disturb the performance of electromagnetic
fields such as emitted by alarm systems of shops. For additional
detail regarding the testing and use of this product with respect to
electromagnetic emissions, see Appendix, Table 1 (Guidance and
manufacturers declaration - electromagnetic emissions)
H. HEAD ARRAY SAFETY AND RFI
E. IMMUNITY LEVEL
WARNING
1. The level of EM is measured in volts per meter (V/m). Every
power wheelchair can resist EMI up to a certain level. This is
called its “immunity level”.
2. The higher the immunity level, the less the risk of EMI. It is
believed that a 20 V/m immunity level will protect the
power wheelchair user from the more common sources of
radio waves.
3. The common configuration tested and found to be immune
to at least 20 V/m is: Quickie Pulse power wheelchair with a
right-hand mounted RNET remote joystick system, 18" seat
width, 18" seat depth, dual post height adjustable armrests,
fixed tapered legrests with a two piece footplate, and Gp 22
gel cell batteries.
4. All After Market input device options, classified as breath controls, Proportional controls, and/or Switched controls that
can be used with this powerchair, have an unknown effect on
their immunity level to different types of EMI. They have not
been specifically tested with the Pulse 5/6 and RNET control
system.
5. All modifications required for the common configuration to comply with ANSI/RESNA WC2/21 have been installed
WARNING
If there is any doubt that the specialty control input device is not
immune to 20V/m, extra care should be taken around known
sources of EMI.
WARNING
If you have a Head-array, the sensors used in the product have the
potential to operate unintentionally if moisture or any substance
that is electrically conductive is present in sufficient quantities.
Electro magnetic interference from electrical power lines and certain types of phones can cause the sensors to activate.
These sensors are capacitive in nature, and can generate an electronic field, which can be affected by liquids and/or a source of
radio frequency Interferance (RFI). Any material that is conductive
has the potential to activate the Head-array unintentionally.
Avoid
use under high power lines and around cell phones.
Avoid
the use of a Head Array in rain or snow and protect against
the potential of spilled liquids on the sensors.
Avoid
cell phones and electronic devices in proximity to the array.
Avoid
any source that has the potential of (RFI).
Warn
the user of this chair that the chair controls have the potential of acting erractically or making sudden stops, if (RFI) is not
avoided.
If any (RFI) causes erratic behavior, immediately cut off the power
to the wheelchair, and wait until the interference passes.
119832Rev. G
6
QUI CK IE PU LS E
WARNING
Heed all warnings in this section. If you fail to do so, a fall, tip-over
or loss of control may occur and cause severe injury to you or
others.
A. NOTICE TO USER AND ATTENDANTS
WARNING
User:
1. Before using this chair, you should be trained in its safe use
y your health care professional.
b
2. Every wheelchair is different. Take the time to learn the feel
of this chair before you begin riding.
3. Be aware that you must develop your own methods for the
safe use of this chair that are best suited to your level of
function and ability.
4. Have someone help you practice bending, reaching and
transfers until you learn how to do them safely.
5. Never try a new maneuver on your own unless you are sure
it is safe.
6. Get to know the areas where you plan to use your chair.
Look for hazards and learn how to avoid them.
7. Always wear a positioning strap.
8. Do not use a wheelchair if the joystick does not spring back
to the neutral position.
9. Do not use your wheelchair if the joystick boot is ripped or
damaged.
10. Do not try to tip this wheelchair without an attendant present.
11. Do not allow additional riders, the chair may become unstable.
User and Attendants:
1. When transferring the user in or out of the wheelchair
never use the footplate as a platform.
2. Do not lift this wheelchair by any parts that are removable,
doing so may result in damage to the wheelchair or injury to
the user.
3. Never try to stop or slow this wheelchair with the wheel
locks (if applicable). Wheel locks are designed to prevent
the chair from moving when stopped. They are not brakes.
4. Always keep your hands and body parts clear of moving
parts to help prevent injuries.
Attendants:
WARNING
Make sure you heed all warnings and follow all instructions in each
section of this manual. Warnings that apply to the user also apply
to you.
1. Do not stand or sit on any portion of this wheelchair.
2. You need to work with the user, and the user’s doctor,
nurse or therapist, to develop safe methods best suited to
your abilities and those of the user.
3. To manually push the chair you must release the motor locks.
• Do not engage or disengage motor locks
the chair is
• Make sure you have full control over the chair when you
release the motor locks. When you do so the chair will not
have brakes.
• Make sure the chair is on level ground before you release
the motor locks.
4. Propel this chair by the push handles only. They provide
secure points for you to hold the rear of the chair to prevent a fall or tip-over.
5. Check to make sure push handle grips will not rotate or slip off.
off
.
unless
power to
VI. GENERAL WARNINGS
B. WEIGHT LIMIT
WARNING
1. The user plus items carried should never exceed the total
weight capacity identified on your chair.
2. Never use this chair for weight training.
3. Exceeding the weight limit is likely to damage the seat,
frame, or fasteners, and may cause severe injury to you or
others from chair failure.
. Exceeding the weight limit will void the warranty.
4
C. CONTROLLER SETTINGS
WARNING
Be aware that you may need to adjust the controller settings of
your chair.
1. Check and adjust the settings every six to twelve months.
2. Consult your supplier to adjust the control settings immediately if you notice any change in your ability to:
• Control the joystick
• Hold your torso erect
• Avoid running into objects.
D. SAFETY CHECK-LIST
WARNING
Before each use of this chair:
1. Make sure the chair operates smoothly. Check for noise,
vibration, or a change in ease of use. (They may indicate low
tire pressure, loose fasteners, or damage to your chair).
• Inspect any problem. Your authorized dealer can help you
find and correct the problem.
2. Make sure batteries are charged. Green lights on charge
indicator will light up when charge is full. Yellow lights indicate battery charge level is getting low. Red lights indicate
batteries are in immediate need of charging.
E. CHANGES & ADJUSTMENTS
WARNING
Never
use non-Quickie parts to replace Quickie provided parts or
make changes to your chair unless authorized by Sunrise. (Doing so
will void the warranty and may create a safety hazard.)
F. ACCESSORIES
WARNING
Accessories designed by manufacturers other than Sunrise, not available through Sunrise order process have not been tested or
approved for use by Sunrise.
1. If you modify or adjust this chair it may increase the risk of a
fall or tip-over.
2. Modifications unauthorized by Sunrise constitutes remanufacturing of the wheelchair. This voids the warranty. The
user then assumes all future liability for the wheelchair.
7
119832 Rev. G
QUI CK IE PU LS E
VI. GENERAL WARNINGS
G. WHEN SEATED IN A PARKED
WHEELCHAIR
WARNING
Always
1.
2. Make sure that persons who help you (for example, store
turn off all power to your chair when you are
parked, even for a moment. This will prevent:
• Accidental movement from contact with the joystick by
you or others.
• Unintended brake release or movement from EMI sources.
See Section V)
(
clerks) are aware of the joystick and do not touch it. If they
do, your chair may move suddenly when you do not expect
it.
H. ENVIRONMENTAL CONDITIONS
WARNING
Your chair is not designed for use in a heavy rain storm, or in
snowy or icy conditions.
1. Contact with water or excessive moisture can cause an electrical malfunction. The frame, motors and other chair parts
are not water-tight and may rust or corrode from the
inside.
To avoid a chair failure:
• Minimize exposure of your chair to rain or very
wet conditions.
Never
•
• Do not use your chair in fresh or salt water (such as at the
• Make sure battery cover is secure.
• Replace joystick boot if it becomes torn or cracked.
• Make sure all electrical connections are secure.
• Dry the chair as soon as you can if it gets wet, or if you
2. Proceed slowly and use extra care if you must operate your
chair on a wet or slick surface.
• Stop if one or both main wheels lose traction. If this
•
• When in doubt, have someone help you.
3. When not in use, keep your chair in a clean, dry place.
take your chair into a shower, tub, pool or sauna.
edge of a stream, lake, or ocean).
use water to clean it.
occurs, you may lose control of your chair or fall.
Never
operate your chair on a slope or ramp if there is
snow, ice, water or oil film present.
WARNING
Extra caution should be used when employing the disc switch or
the proximity head array as control devices. These two devices
are susceptible to malfunction when wet.
I. TERRAIN
WARNING
1. This chair will perform at it’s best on firm, even surfaces
such as concrete, asphalt and indoor flooring.
2. Although equipped with suspension, the performance can be
substantially reduced on uneven surfaces and rough terrain.
3. Do not operate the chair on sand, loose gravel or soil.
Doing so may damage wheels, bearings, axles, motors or
loosen fasteners.
J. STREET USE
WARNING
1. This product is not intended for street use. Avoid streets
whenever possible.
2. Obey and follow all legal pedestrian pathways, and laws that
apply to pedestrians.
. Be alert to the danger of motor vehicles in parking lots, or if
3
you must cross a road.
4. It may be hard for drivers to see you. Make eye contact with
drivers before you proceed. When in doubt, yield until you
are sure it is safe.
K. MOTOR VEHICLE SAFETY
WARNING
Identify whether or not your chair has been manufactured with
the Transit Option installed.
If your chair is not equipped with the Transit Option: The wheelchair does not meet federal standards for seating while travelling
in a motor vehicle.
NEVER
1.
2.
3.
4.
5.
If your chair is equipped with the Transit Option:
T: “Transit Option and use”.
let anyone sit in this chair while in a moving vehicle.
ALWAYS
manufacture) motor vehicle restraints. In an accident or
sudden stop the rider may be thrown from the chair.
Wheelchair seat belts will not prevent this, and further
injury may result from the belts or straps.
NEVER
may shift and interfere with the driver.
ALWAYS
DO NOT
vehicle accident. It may have changed the structure of the
chair, and damaged, or broken components. This could lead
to a risk of injury or damage to your chair. If the wheelchair
has been involved in an accident, discontinue use and contact your supplier for a thorough inspection.
secure the rider with OEM (original equipment
transport this chair in the front seat of a vehicle. It
secure this chair so that it cannot roll or shift.
use any chair that has been involved in a motor
See section VII-
L. CENTER OF BALANCE
WARNING
The point where this chair will tip forward, back, or to the side
depends on its center of balance and stability.
The Center Of Balance Is Affected By:
1. The seat height and seat angle.
2. A change in your body position, posture or weight distribution.
3. Using this chair on a ramp or slope.
4. The use of a back pack or other options, and the amount of
added weight.
5. Center or rear Drive wheel positioning.
To Reduce The Risk Of A Fall Or Tip-Over:
1. Whenever a condition exists that may change the center of
balance, reduce speed, proceed cautiously.
2. When in doubt, always have someone help you.
119832Rev. G
8
QUI CK IE PU LS E
VI. GENERAL WARNINGS
M. TRANSFERS
WARNING
It is dangerous to transfer on your own. It requires good balance
and agility. Be aware that there is a point during every transfer
when the wheelchair seat is not below you. To prevent a fall:
Always
1.
2. Make sure motor brakes are engaged. This keeps the chair
3. Work with your health care professional to learn all safe
4. Move your chair as close as you can to the seat you are
5. Rotate the front casters until they are as far forward as possible.
6. Be careful of the footrests. If you can, remove or swing
7. Make sure armrests do not interfere.
8. Transfer as far back onto the seat surface as you can. This
turn off power before you transfer to or from your
chair. If you fail to do so you may touch the joystick and
cause your chair to move when you do not expect it.
from moving when you transfer.
methods for transfers.
Learn how to position your body and how to support
•
yourself during a transfer.
• Have someone help you until you are sure you can do a
safe transfer on your own.
transferring to. If possible, use a transfer board.
them out of the way.
• As a standard rule, never stand on footrests when you
transfer. Doing so may damage them or cause your chair
to tip. If the footplate is in contact with the ground, it is
possible to use the footplate for a transfer.
• Make sure your feet do not “hang up” or get caught in the
space between the footrests.
will reduce the risk that you will miss the seat or fall.
N. REACHING OR LEANING
WARNING
Reaching or leaning affects the center of balance of your chair. If
done improperly, a fall or tip-over is likely. When in doubt, ask for
help or use a device to extend your reach.
To Reduce the Risk of injury and/or Damage to the Chair:
Never
1.
2.
3.
4.
5.
6.
IF YOU MUST REACH OR LEAN, DO SO AT YOUR OWN RISK.
Remember to:
1. Move your chair as close as you can to the object you wish
2. Rotate the front casters until they are as far forward as pos-
NOTE
3. Turn off all power to your chair. If you fail to do so, you
reach or lean if you must shift your weight sideways or
rise up off the seat.
Never
reach or lean if you must move forward in your seat
to do so. Always keep your buttocks in contact with the
backrest.
Never
reach with both hands (you may not be able to catch
yourself to prevent a fall if you lose your balance).
Never
try to pick up an object from the floor by reaching down
between your knees.
Never
put pressure on the footrests while reaching.
Never
reach or lean over the top of the seat back. This may
damage the backrest and cause you to fall.
to reach.
sible. This makes the chair more stable.
–To do this: Move your chair past the object you want to reach,
then back up alongside it. Backing up will rotate the casters forward.
may touch the joystick and cause your chair to move when
you do not expect it.
O. DRESSING OR CHANGING CLOTHES
WARNING
Be aware that your weight will shift if you dress or change clothes
while seated in this chair. To make the chair more stable, rotate
the front casters until they are in the
forward position
.
P. OBSTACLES
WARNING
Riding over curbs or obstacles can cause tipping and serious bodily
harm. If you have any doubt that you can safely cross any curb or
obstacle, ALWAYS ASK FOR HELP. Be aware of your riding skills
and personal limitations. Develop new skills only with the help of
a companion.
1. Be aware that thresholds are very dangerous. (Even a small
change in height may stop a caster wheel and cause your
chair to tip). You may need to:
• Remove or cover threshold strips between rooms.
• Install a ramp at entry or exit doors.
2. Keep your eyes moving when you ride; scan the area well
ahead of your chair.
3. Make sure the floor areas where you use this chair are level
and free of obstacles.
Q. DRIVING IN REVERSE
WARNING
Use extra care when you drive your chair in reverse. You may
lose control or fall if one of the rear wheels hits an object.
1. Operate your chair slowly and at an even speed.
2. Stop often and check to make sure your path is clear of
obstacles.
R. RAMPS, SLOPES & SIDEHILLS
WARNING
Your center of balance changes when you are on a slope.
NOTE –
Beware Of:
“Slope” includes a ramp or sidehill. Your chair is less sta-
ble when it is at an angle. Never use this chair on a
slope unless your are sure it is safe. When in doubt,
have someone help you.
1. Steep slopes. Do Not use this chair on a slope steeper than
6%. (A 6% slope means: One foot in elevation for every ten
feet of slope length).
2. Wet or slippery surfaces (such as when ice, snow, water or
oil film is present). A loss of traction may cause a fall or tipover.
3. A change in grade on a slope (or a lip, bump or depression).
These may cause a fall or tip-over.
4. A drop-off at the bottom of a slope. (A drop-off of as small
as 3/4 inch (19 mm) can stop a front caster and cause the
chair to tip forward).
9
119832 Rev. G
QUI CK IE PU LS E
S. REDUCE THE RISK OF A FALL, TIP-OVER OR
LOSS OF CONTROL
WARNING
Never
1.
2.
.
3
4. Keep your chair moving at a slow, steady speed. Keep con-
use your chair on a slope unless you are sure you can
do so without losing traction.
Always
go as straight up and as straight down as you can.
Do not
•
•
Always
be wide enough so that the wheel won’t roll off of the side
of the ramp.
trol over the chair at all times.
• On a descent, do not let your chair accelerate beyond its
• If the chair picks up speed, center the joystick to slow
• If you stop, re-start slowly
“cut the corner” on a slope or ramp.
Do not
turn or change direction on a slope.
tay in the center of the ramp. The ramp needs to
s
normal speed.
down or stop.
T. RAMPS AT HOME & WORK
WARNING
Before driving on a ramp, survey the condition of the ramp. On
slippery ramps traction may be reduced causing your wheelchair
to slide.
VI. GENERAL WARNINGS
Avoid
4.
moving forward if a wheel is “hung up” on the lip of
the ramp. Backup, reposition the caster for a more direct
approach. And slowly try again.
V. CURBS & SINGLE STEPS
WARNING
1. Sunrise recommends that you avoid climbing and/or descending
a curb, single step, or other obstacle, and that a ramp or curb
cutout is always used.
2. If you must climb or descend a curb, single step, or other
obstacle that is greater than 2.5", it is recommended to have
person assist you in doing so.
a
DO NOT
3.
greater than 4" high.
4. If you must climb or descend a curb or step alone do so at your
own risk using extreme care and use the following procedure:
• Proceed slowly, at a steady speed
• Go as straight up or down as you can over the obstacle.
Never turn when trying to climb or descend an obstacle,
doing so may result in a fall or tip-over.
5. Failure to follow the above recommendations may cause:
• A Fall or Tip Over
• Damage to the frame, wheels, axles or other parts, or
loose fasteners.
try to climb a curb, single step, or other obstacle
W. STAIRS
WARNING
NOTE–
Make sure ramps meet all Building Codes for your area.
1. For your safety, have a licensed contractor build or remodel
the ramp to meet all local codes and standards.
2. The proper design will vary, depending on such things as: the
length and height of the ramp; the need for an intermediate
platform; landing size; doors, and the direction of swing, and;
whether the ramp includes a turn or angle.
At A Minimum:
1. Open sides of ramp must have side rails to prevent your
chair from going over the edge.
2. Slope must not be steeper than one inch in height for every
one foot of slope length (approximately 10º).
3. Ramp surface must be even, and have a non-skid surface.
4. You may need to add a section at the top or bottom to
avoid a lip or drop-off.
5. Ramp must be sturdy. Add bracing if needed, so ramp does
not “bow” when you ride on it.
U. WHEELCHAIR LIFTS
WARNING
Wheelchair lifts are used in vans, buses, and buildings to help you
move from one level to another.
Always
1.
lift. If you fail to do so, you may touch the joystick by accident and cause your chair to drive off the platform. (Be
aware that a “roll-stop” at the end of the platform may not
prevent this).
2. Make sure there is not a lip or drop-off at the top or bottom of the platform. These may cause a fall or tip-over.
When in doubt, have someone help you.
Always
3.
falls while on a lift.
off
turn
position the user securely in the chair to help prevent
all power to your chair when you are on a
WARNING
Never use this chair to go up or down stairs, even with an attendant. Doing so is likely to cause a fall or tip-over.
X. ESCALATORS
WARNING
Never take this chair on an escalator, even with an attendant.
Doing so is likely to cause a fall or tip-over.
119832Rev. G
10
QUI CK IE PU LS E
WARNING
Note: If you use parts or make changes not authorized by Sunrise
t may create a safety hazard and will void the Warranty.
i
A. ARMRESTS
WARNING
1. Armrests will not bear the weight of this chair.
Never
2.
lift this chair by its armrests. They may come loose
or break.
VII. WARNINGS: COMPONENTS AND OPTIONS
F. MOTOR LOCKS
WARNING
1. Do not engage or disengage motor locks
2. Be aware that the chair
. Make sure that the person pushing the chair has full control
3
4. Make sure that the chair is on level ground when motor
off
chair is
locks are in the free-wheel position.
when motor locks are disengaged.
locks are disengaged.
.
will not have brakes
unless
when motor
power to the
B. BATTERIES
WARNING
Always
1.
2.
3. Only
4. Read all of section
wear rubber gloves and safety glasses when you han-
dle batteries.
Never
smoke or hold an open flame near batteries. They
are a known explosion hazard.
deep cycle sealed case
used in this device.
X. Batteries
or charge batteries.
construction batteries should be
before attempting to change,
C. CUSHIONS & SLING SEATS
WARNING
1. Standard foam cushions and other body supports are not
designed for the relief of pressure. Do not sit directly on a
sling surface.
2. If you suffer from pressure sores, or if you are at risk that
they will occur, you may need a special seat system or a
device to control your posture.
• Consult your healthcare professional to find out if you
need such a device for your well-being.
D. FASTENERS
WARNING
Many of the screws, bolts and nuts on this chair are special highstrength fasteners. Use of improper fasteners may cause your
chair to fail.
1. Only use fasteners provided by Sunrise.
2. If fasteners become loose, tighten them immediately.
3. Over- or under-tightened fasteners can cause damage to
your chair or it’s components.
E. FOOTPLATE & FOOTRESTS
WARNING
1. At the lowest point, footrests should be
(65 mm) off the ground. If set too LOW, they may “hang
up” on obstacles you can expect to find in normal use. This
may cause the chair to stop suddenly and tip forward.
2. To avoid a trip or fall when you transfer:
• Make sure your feet do not “hang up” or get caught in the
space between the footrests.
• Avoid putting weight on the footrests, as the chair may tip
forward.
• Remove or swing the footrests out of the way, if possible.
3. The footrest should always be in the down position when
operating the chair.
4. Never lift this chair by the footrests. Footrests detach and
will not bear the weight of this chair. Lift this chair only by
non-detachable parts of the main frame.
at least 2 1/2 inches
G. ON/OFF SWITCH
WARNING
Never
1.
2. To slow your chair to a stop, return the joystick to neutral.
use the ON/OFF switch to stop the chair
an emergency. This will result in an
cause you to fall.
abrupt
except
stop, and may
in
H. PNEUMATIC TIRES
WARNING
Proper inflation extends the life of your tires and makes your chair
easier to use.
1. Do not use this chair if any of the tires are under- or overinflated. Check weekly for proper inflation level, as listed on
the tire sidewall.
2. Low pressure in a tire may cause the chair to veer to one
side and result in a loss of control.
3. An over-inflated tire may burst.
Never
4.
5. Driving over sharp objects may cause damage to pneumatic
use a gas station air pump to inflate a tire. Such
pumps provide air at
to burst. To prevent tire damage:
• Use a hand pump (or
• Use a tire gauge to check pressure.
tires and tubes.
high volume
low volume
, and could cause the tire
air pump) to inflate tires.
I. POSITIONING BELTS (Optional)
WARNING
The positioning belt is predominately used to support your posture. It can also be used to limit slipping and/or sliding that you
might experience when the chair is in motion. The positioning
belt is not a transit rated safety belt and should not be used in the
place of a seat belt while being transported in a motor vehicle.
Improper use of Positioning belts may cause severe injury or
death. If you use a positioning belt, be sure to follow the recommendations in this section:
1. Make sure the rider does not slide down in the wheelchair
seat. If this occurs, the rider may suffer chest compression
or suffocate due to pressure from the belts.
2. The belts must be snug, but must not be so tight that they
interfere with breathing. You should be able to slide your
open hand, flat, between the belt and the rider.
3. A pelvic wedge or a similar device can help keep the rider
from sliding down in the seat. Consult with the rider’s doctor,
nurse or therapist to find out if the rider needs such a device.
4. Use positioning belts only with a rider who can cooperate.
Make sure the rider can easily remove the belts in an emergency.
11
119832 Rev. G
QUI CK IE PU LS E
VII. WARNINGS: COMPONENTS AND OPTIONS
5. NEVER use positioning belts
a. As a patient restraint. A restraint requires a doctor’s
order.
b. On a rider who is comatose or agitated.
c. As a motor vehicle restraint. In an accident or sudden
stop the rider may be thrown from the chair.
Wheelchair seat belts will not prevent this, and further
f you fail to heed these warnings, damage to your chair, a fall, tip-
I
over or loss of control may occur and cause severe injury to the
rider or others.
injury may result from the belts or straps.
J. PUSH HANDLES
WARNING
1. Push handles provide secure points for an attendant to propel
and control the chair. This helps to prevent a fall or tip-over.
2. Check to make sure push handle grips will not rotate or slip off.
K. SEATING SYSTEMS
WARNING
1. Use of a seating system not approved by Sunrise may alter the
center of balance of this chair. This may cause a fall or tip-over.
Never
2.
3. Never raise your seating system to a height of more than
change the seating system of your chair unless you
consult your supplier first.
22" (measuring from the front of the seat pan to the floor)
with all actuators in their home position.
L. UPHOLSTERY FABRIC
WARNING
1. Replace worn or torn fabric of the seat sling and seat back
as soon as you can. If you fail to do so, the seat may fail and
cause you to fall. Worn fabrics may increase the potential
for a fire hazard.
2. Sling fabric will deteriorate with age and use. Look for fraying, thin spots, or stretching of fabric at rivet holes. Replace
fabric as required.
3. Be aware that washing may reduce flame retardation qualities of the fabric.
M. SUSPENSION
WARNING
No component of the chair, was made with natural rubber latex,
Including the Suspension system.
P. POWER SEATING (SC,MPC)
WARNING
1. Operation
• While driving this wheelchair in the reclined, elevated, or
tilted position use caution.
Do Not attempt to operate any power seating option
•
while positioned on an incline.
• Do Not attempt to operate any power seating option
while this wheelchair is in motion.
• Do not attempt to operate the lift or tilt power seating
options around children.
• Through programming it is possible to reverse the direction
of all powered seating functions, ensure you know which
direction your seat is going to move before operating.
2. Reduced Speed Driving (Creep)
This power chair is designed to automatically reduce the maximum
driving speed to a creep mode when certain power seating limits
are reached.
3. Pinch points
Pinch points may occur when operating the powered seating
options on this chair. Ensure all hands and body parts are clear of
all power seating components that may result in pinch points
before operating them.
4. Tilting Power Base with Push Handles
Do not attempt to tilt power wheelchairs by pulling down on the
push handles. Power wheelchairs have heavy bases. As such, attempting to tilt a power wheelchair to traverse obstacles can damage components in the seating system and/or modular actuators.
5. Remain Clear During Power Accessory Operation
Please stay clear of any powered actuator while the component is
in motion. Sunrise power mechanisms move over large ranges of
travel. Users should be aware of their surroundings while components are in motion.
6. Maximum User Weight
Do not exceed the weight capacity for your specific chair/seating system configuration. Doing so could result in premature failure or injury.
7. Latch Mode
While operating any power seating function in latched mode use
caution. In latch mode, powered seating will not stop until a
reverse command is performed or the end of travel is met.
N. WIRING
WARNING
Never pull on cables directly. This can result in wires breaking
inside the connector or harness. To remove a plug or connector,
always grasp the plug or connector itself.
O. ASSIGNABLE CONTROLS
WARNING
It is possible to assign a function to buttons, or jacks of your wheelchair . If controls have been assigned to perform a dual or alternate
function ensure you know what each control operates. Please contact your Authorize Dealer or the Quickie Technical Service
Department if you do not receive this information.
119832Rev. G
Q. S.P.O.T.
POWER ACCESSORY (
(Single Power Option Tilt)
SC only
)
WARNING
The powered S.P.O.T. accessory for this chair has a maximum
user weight capacity of up to 300 lbs. Never exceed this capacity
while operating the powered actuator.
WARNING
The powered S.P.O.T. should not be operated for more than
three minutes of continuous use. Doing so may shorten the life of
the powered S.P.O.T.
12
QUI CK IE PU LS E
R. POWER RECLINE
WARNING
Pinch Point
Avoid putting hands or fingers near the power recline mechanism
while in operation.
Weight Capacity
The maximum user weight capacity for the power recline is 250lbs
if the seat depth is less than 17 inches, and up to 300 lbs for any
seat depth over 17 inches. Exceeding this weight capacity could
lead to injury and/or permanent damage to the equipment.
VII. WARNINGS: COMPONENTS AND OPTIONS
WARNING
Wheelchairs with adjustable seat angles must be set to 10°. Do
not alter or substitute wheelchair frame parts, components, or
seating systems.
A sudden stop and/or collision may structurally damage your
wheelchair. Wheelchairs involved in such incidents should be
replaced.
Spill proof batteries, such as “gel cells”, should be installed on
wheelchairs that will experience travel in a motor vehicle.
S. POWER LEGREST ACCESSORY
The power legrest accessory has a maximum user weight
capacity of up to 300 lbs depending on your chair configuration.
Never exceed this capacity while operating the powered actuator.
T. TRANSIT OPTION AND USE
Refer also to sections VI-K: “Motor Vehicle Safety” for additional
transit option and motor vehicle warnings.
WARNING
Contact Sunrise Medical customer service (800-333-4000) with
any questions about using this power wheelchair for seating in a
motor vehicle, or if your chair is a candidate for the transit option.
Whenever possible, wheelchair occupants should transfer into the
vehicle seat and use the OEM (Original Equipment Manufacturer)
vehicle-installed restraint system.
This wheelchair has been dynamically tested in a forward-facing
mode with a specified crash test dummy restrained by both pelvic
and upper-torso belt(s) (shoulder belts). It has been determined
that both the pelvic and upper-torso belt(s) should be used to
reduce the possibility of head and chest impacts with vehicle components. When travelling in a motor vehicle, use only Wheelchair
Tie-down and Occupant Restraint Systems (WTORS) which meet
the requirements of the SAE (Society of Automotive Engineers)
J2249 Recommended Practice.
WARNING
This wheelchair has been tested for seating in a motor vehicle with
the factory-installed seating system only. This wheelchair must be
in a forward facing position during travel in a motor vehicle.
This wheelchair is equipped with wheelchair-anchored pelvic belts.
It has been dynamically tested to rely on wheelchair-anchored
pelvic belts. If desired, vehicle-anchored pelvic belts may also be
used. It is strongly recommended that the combination of both
pelvic and upper-torso belt(s) be used to reduce the risk of injury
if a sudden stop and/or collision were to occur.
WARNING
NOTE–
Pulse for the purposes described in this manual.
ABOUT TRANSPORT READY PACKAGES
The Quickie Pulse Transit System includes four factory-installed
transport brackets and an optional wheelchair anchored pelvic
belt. The Quickie Pulse 6 has been crash-tested in accordance
with ANSI-Resna WC Vol 1 Section 19 Frontal Impact Test
requirements for wheelchairs with a 170 lb crash dummy. As of
this date, the Department of Transportation has not approved any
tie-down systems for transportation of a user while in a wheelchair, in a moving vehicle of any type. It is Sunrise Medical’s position that users of wheelchairs should be transferred into the vehicle seating when transport is necessary and that the restraints
made available by the auto industry be used.
tion systems
COMPLIANCE INFORMATION
This wheelchair conforms to the requirements of the ANSI-Resna
WC Vol 1 Section 19.
NOTE–
Only use the transit brackets included with the Quickie
Sunrise Medical does not recommend any wheelchair transporta-
ANSI stands for: American National Standards Institute.
Resna: Rehabilitation Engineering and Assistive Technology
Society of North America.
WARNING
This wheelchair has been dynamically tested in a forward-facing
mode with a specified crash test dummy, restrained by both pelvic
and upper-torso belts in accordance with ANSI-Resna WC Vol 1
Section 19. Both pelvic and upper-torso belts should be used to
reduce the possibility of head and chest impacts with vehicle components in the event of a sudden stop and/or collision.
WARNING
To reduce the potential of injury to vehicle occupants, wheelchairmounted accessories, including but not limited to IV poles, trays,
respiratory equipment, backpacks, and other personal items should
be removed from the wheelchair and secured separately. Postural
supports, positioning devices, and/or strap(s) should not be relied
on for occupant restraint. These items may be used in addition to
the wheelchair anchored, or vehicle-anchored belts.
13
119832 Rev. G
QUI CK IE PU LS E
VII. WARNINGS: COMPONENTS AND OPTIONS
1
SECURING THE WHEELCHAIR TO THE VEHICLE
2
WARNING
This wheelchair must be in a forward facing position during travel in a motor vehicle.
The recommended clear zones for wheelchair seated occupants restrained by both
elvic and upper-torso belt(s) and only by a pelvic belt are shown in the diagrams
p
and described below. Frontal Clear Zones (FCZ) need to be larger when upper
torso belt(s) are not used. The Rear Clear Zone of 16in is measured from the rearmost point on an occupant’s head. The Frontal Clear zone is measured from the
front most point of an occupant’s head and is 26-inches with pelvic and upper-torso
belt(s) and 37 inches with only a pelvic belt. The frontal clear zone may not be
achievable for wheelchair- seated drivers.
The estimated seated height (HHT) from the ground or floor to the top of the
wheelchair-seated occupant’s head ranges from approximately 47 inches for a small
adult female to about 61inches for a tall adult male.
SECUREMENT POINTS
Rear securement points(A), front securement points(B), Pelvic Belt Securement
point(C), Attach WTORS to the tie-down brackets in accordance with the manufacturer’s instructions and SAE j2249.
SECURING THE WHEELCHAIR
This wheelchair is to be used only with Wheelchair Tie-down and Occupant
Restraint Systems (WTORS) that have been installed in accordance with the manufacturer’s instructions and SAE J2249.
NOTE–
A copy of SAE J2249 Wheelchair Tie-down and Occupant Restraint Systems
(WTORS) for use in Motor Vehicles can be obtained from:
SAE International
400 Commonwealth Drive.
Warrendale, PA. 15096-0001
(877) 606-7232 or (724) 776-4970
1
2
HHT
SECURING THE OCCUPANT:
3
WHEELCHAIR-ANCHORED BELTS
4
WARNING
Only use a pelvic belt system that meets the requirements of ANSI-Resna WC Vol 1
Section 19 and SAE J2249, and has been specified to work in conjunction with the
Quickie Pulse 6 transit system.
1. Installation
a. Install the pelvic belt (D) onto the pelvic belt securement point anchored to
the seating frame of the Quickie Pulse 5 or 6. Using a 10mm Hex key, torque
the screw to 144in-lbs securing the pelvic belt to the mounting anchor (C).
b. Repeat step 1 for the opposite side.
c. Upper torso attachment point(E) shown.
3
B
A
C
4
D
E
C
119832Rev. G
14
Loading...