Sunrioy SR-300-S, SR-500-S, SR-600-S, SR-1200-S, SR-1000-S User Manual

Pure Sine Wave Inverter USER MANUAL

DC-AC Power Inverter

Special Features:

 Input & output fully isolation
 Input Protections: Reverse Polarity(Fuse)/ Under Voltage/ Over Voltage
 Output Protection: Short Circuit / Overload /Over Temperature
 Load 120~150%(3min.);200%（3sec)
 Power ON-OFF switch
 USB:5V,500mA(Optional)
 Protection: LED Indicator
 12V or 24V or 48VDC input
 Output waveform: Pure sine wave
 Fuse: Built-in
 Frequency: 50Hz±1%,60±1%
 CE and RoHS Approved

Thank you for purchasing ours Pure Sine Wave Inverter, Please Carefully read,
understand and comply with all instructions before using.

2

Table of contents

1. Introduction………………………………………………………….3

1.1 What’s an inverter…………………………………………….3

1.2 Pure Sine Wave Inverter……………………………………. .3

2. Main Components………………………………………………...3-5

2.1 Front panel…………………………………………………….3

2.2 Rear panel………………………………………………...…...4

3. How to Use Inverter….…………………………………………...5-8

3.1 Load consideration………………………………………….…5

3.2 Configuring the Battery Bank …………………………...…...6

3.3 Battery wiring examples………………………………….……6

3.4 Placement of the inverter…………………………….………..7

3.5 Mounting position of the inverter…………………….………7

3.6 Getting Connected……………………………………….…….8

4. Important Safety Instructions………………………………………8

5. Protection Feature………………………………………………….9

6. Troubleshooting Reference……………………………...…........9-11

7. Main Specifications………………………………………...............12

8. Maintenance……………………………………………………..…13

9. Warranty……………………………………………………….…..13

3

1. Introduction

1.1 What is an Inverter?

Power inverter is an electronic device that convert DC(Direct Current) battery power

to standard AC(Alternating Current) power. DC is the power that is produced by

battery while AC is the standard power needed to run electrical equipment. A power

inverter does the opposite of a rectifier and is used in places and situations where AC

power is not available.

1.2 Pure Sine Wave Inverter

If you want to run your equipment exactly to the manufacturer’s specifications,

choose a pure sine wave inverter. With pure sine wave, motor loads start easier and

run cooler. Some equipment only operate properly with pure sine wave inverter, such

as laser printers, variable speed motors and digital clocks.

2. Main Components

2.1 Front Panel

The front panel view shows the inverter’s ON/OFF Switch, AC Output

Receptacle, LED Indicator Light, Vent Outlet

4

A. ON/OFF Switch.

This switch controls ON/OFF operation of the inverter.
B. LED Indicator Light: Fault, Power
a) Fault: Turns Red shows fault, reference to Troubleshooting
b) Power: This light will illuminate continuously whenever connected
equipment is receiving battery-supplied, inverted AC power.
C. AC Output Receptacle: For application demands of different geographic
areas all over the world, there are many different kinds of optional AC
receptacle to choose from.

D. Vent Outlet.

To decrease the temperature of the inverter.

E. Chassis Ground

Properly grounds the Inverter to vehicle grounding system or to earth ground.

F. USB: 5V 2.1A

Seek professional assistance if you are unfamiliar with electrical wiring.

2.2 Rear Panel

The rear panel view shows the inverter’s Cooling fan, DC Battery Terminals,
Fuse, Chassis Ground