Sunricher Technology ZG1029 User Manual

4 in 1 Universal ZigBee LED Controller
ZG. 01029.04737
Operation
1.Do wir ing a ccordin g to connec tion diag ram c orrectl y, plea se po wer off and p ower on the d evice onc e
a device m ode i s selecte d so that the s elected m ode c an be activ ated.
Important: Re ad All I nst ruc tio ns Pr ior t o Ins tal lat ion
Function introduction
12-24V DC Power in put
1 2ON3
Dial swi tch for dev ice mo de select ion, DIM, C CT, RGBW and RGB+ CCT 4 mo des are ava ilable, factor y default i s RGB+ CCT mode
1) Under R GBW m ode, W chan nel can onl y be turned o n thr ough colo r tempera tur e control c ommand (R GBW will be id ent ified as RG B+CCT by zi gbee). Co lor tempe rature co ntr ol will mix R GB channe ls as 1 c hannel wh ite and then m ake c olor tuni ng with the 4 th channe l whi te. Once tu rned on, th e bri ghtness o f white cha nnel will b e contro lle d togethe r with RGB ch annels.
2) Under R GB+ CCT mo de, RGB cha nne ls and tuna ble white c han nels a re co ntrolle d separat ely, they ca n not be turne d on an d control led at the sa me time.
LED indi cator, sta ys sol id on w hen po wer o n the co ntrolle r, turns off a fter adde d to a zigbee h ub, indic ates (sam e stat us as c onne cted load) wh en progra m the contr olle r (ne twor k pairing , touchli nk, facto ry res et)
DC IN PUT
Zig Bee LED C ontro ller
Inp ut Volta ge DC 12- 24V Out put Cur rent 4A /CH Max P ower 48 -96W/ CH
DIM CCT RGB W RGB +CCT
Ta:-2 0-+50
Pro g.
3
1 2
WW-
1- R- R -
2- G- G-
CW-
3- B- B-
WW-
LED O UTPUT
4-
CW-
5-
WW-
W-
CW-
NCNC
Progra m Key: shor t pre ss to s witch on/off t he device,
press and hold dow n to in cre ase/decrease li ght i ntensity
Common An ode Outpu t(+)
CH1:R/ R/WW/1 ou tput (-)
CH2:G/ G/CW/2 ou tput (-)
CH3:B/ B/WW/3 ou tput (-)
CH4:WW /W/CW/4 o utpu t(- )
CH5:CW /NC/NC/ 5 outp ut( -)
NC = No Conn ection
Product Data
Input
Voltage
12-24VDC
Out put
Current
4A/CH
Out put
Power
48-96W/CH
Remarks
Size(LxWxH)
145 x46. 5x16m m
4 in 1 unive rsa l Zigbee LE D control ler based o n lat est ZigBe e 3.0 proto col
4 differ ent devic e modes DIM , CCT , RGBW and RG B+CCT in 1 co ntrolle r, and selec table by di al sw itch
Enable s to co ntrol ON/ OFF, light in tensity, c olor temp erature , RGB c olor of con nected LE D lig hts
Can dire ctl y pair to a com patible Z igBee rem ote v ia Touch link
Suppor ts se lf-form ing zigbe e network w ith out coord inator
Suppor ts fi nd and bind m ode to bind a Z igBee rem ote
Suppor ts zi gbee gree n power and c an bind max . 20 zi gbee gree n power rem ote s
Compat ibl e with univ ersal Zig bee gatew ay or h ub produc ts
Compat ibl e with univ ersal Zig bee remot es
Wat erproof g rade: IP2 0
Ambient
Temperature
-20℃ ~ +50
Max. Casing Temperature
75
Safety & Warn ing s
DO NOT ins tall with p ower appl ied t o device.
DO NOT exp ose the dev ice to mois tur e.
2.This Z igB ee device i s a wireles s receive r tha t communi cates wit h a var iety of Zig Bee compa tible
system s. Th is receiv er receiv es and is con tro lled by wir eless rad io si gnal s fro m the compa tible Zig Bee
system .
3. Zigbee Network Pairing through Coordinator or Hub ( Add ed to a Z igb ee Ne two rk)
Step 1: Re mov e the devic e from prev ious zigb ee ne twork if it h as alread y bee n added to, o therwis e pai ring will
fail. Pl eas e refer to th e part "Fac tor y Reset Man ually".
Step 2: Fr om yo ur ZigBee C ontroll er or hub int erf ace, choo se to add lig hti ng device a nd enter Pa iring mod e as
instru cte d by the cont roller.
Step 3: Re -po wer on the de vice to set i t into netw ork p airing mo de (conne cte d light fla shes twic e slowly) , networ k pai ring mode l asts 15S (e nters int o tou chlink mo de after 15 S), o nce timeo ut, repea t this step .
Step 4: Co nne cted ligh t will blin k 5
times an d the n stay soli d on, then th e
device w ill a ppear in yo ur contro ller's
menu and c an be c ontroll ed throug h
AC Pow er
50/6 0Hz
contro lle r or hub inte rface.
V+ V+ R- R-
G- G­B- B-
V+ V+ WW- WW ­CW- CW -
RGB LED S trip
CCT LED S trip
Max . 20A inpu t
L
12V/24V CV PSU
ZigBe e LED Con troll er
Input Vol tage DC 1 2-24V Output C urren t 4A/CH Max Powe r 48-96 W/CH
Ta:-20-+ 50
Prog.
INPU T
N
G
WW-
1- R- R-
CW-
2- G- G -
WW-
3- B- B-
LED OUTP UT
W-
WW-
4-
CW-
5-
NCNC
CW-
V+
V-
OUTP UT
DC INPUT
3
1 2
DIM CCT RGBW RGB+CC T
1 2ON3
4. TouchLink to a Zigbee Remote
Step 1: Me tho d 1: Short pr ess “Prog ” button (o r re- power on th e device) 4 t ime s to sta rt Touchlin k
commis sio ning (las ts for 180S ) immedia tel y under any c ircumst anc es, once ti me out, rep eat this st ep. Method 2 : Re- power on th e device, Tou chlink co mmissio ning will s tar t after 15S i f it’s n ot ad ded to a zigb ee networ k, 16 5S timeou t. Or start i mmediat ely i f it’s a lready ad ded t o a network , 180S time out . Once time out, repeat t he st ep.
L
12V/24V CV PSU
INPU T
N
G
V+
V-
OUTP UT
Max . 20A inpu t
DC INPUT
ZigBe e LED Con troll er
Zigbee
Remote
< 10cm
Input Vol tage DC 1 2-24V Output C urren t 4A/CH Max Powe r 48-96 W/CH
Ta:-20-+ 50
3
1 2
1 2ON3
DIM CCT RGBW RGB+CC T
Prog.
1- R- R-
2- G- G -
3- B- B-
LED OUTP UT
4-
5-
WW-
CW-
WW-
W-
WW-
CW-
NCNC
CW-
Step 2: Br ing t he remote o r touch pan el within 1 0cm o f the light ing devic e.
Step 3: Se t the r emote or to uch panel i nto Touchli nk commis sioning ,
please r efe r to corres ponding r emote or to uch p anel manu al to learn h ow.
Note: 1) D ire ctly TouchLi nk (b oth not add ed to a ZigBe e network ), ea ch device c an link wit h 1 remote.
2) Tou chL ink after b oth added t o a ZigBee ne two rk, each de vice can li nk wi th max. 30 re motes.
3) For Hue B rid ge & Amazon Ec ho Pl us, add rem ote and dev ice to netw ork f irst then TouchL ink .
4) Af ter Tou chL ink, t he de vice can be c ontroll ed by t he linked r emotes.
Step 4: Th ere shall b e indicat ion o n
the remo te fo r success ful link an d
connec ted l ight will f lash twic e.
AC Pow er
50/6 0Hz
V+ V+ R- R-
G- G­B- B-
V+ V+ WW- WW ­CW- CW -
RGB LED S trip
CCT LED S trip
5. Removed from a Zigbee Network through Coordinator or Hub Interface
From you r Zig Bee contr oller or hu b interfa ce, c hoose to de lete or res et
the ligh tin g device as i nstruct ed. The con nected li ght blink s 3 tim es to
indica te su ccessfu l reset.
6. Factory Reset Manually
Step 1: Sh ort p ress “Pro g.” key for 5 t imes cont inu ously or re -power on t he de vice for 5 ti mes conti nuously i f
the “Pro g.” k ey is not acc essible .
Step 2: Co nne cted ligh t flashes 3
L
Max . 20A inpu t
12V/24V CV PSU
ZigBe e LED Con troll er
Input Vol tage DC 1 2-24V Output C urren t 4A/CH Max Powe r 48-96 W/CH
Ta:-20-+ 50
Prog.
INPU T
N
G
WW-
1- R- R-
CW-
2- G- G -
WW-
3- B- B-
LED OUTP UT
W-
WW-
4-
CW-
5-
NCNC
CW-
AC Pow er
50/6 0Hz
V+ V+ R- R-
G- G­B- B-
V+ V+ WW- WW ­CW- CW -
V+
V-
OUTP UT
DC INPUT
3
1 2
DIM CCT RGBW RGB+CC T
1 2ON3
times fo r suc cessful r eset.
RGB LED S trip
CCT LED S trip
Note: 1) I f the d evice is al ready at fa ctory def aul t setting , there is no i ndi cati on wh en factor y reset aga in .
2) Al l configu ration pa ram eters wil l be reset af ter t he dev ice i s reset or re moved fro m the n etwork.
7. Factory Reset through a Zigbee Remote (Touch Reset)
Step 1: Re -po wer on the de vice to sta rt TouchLin k Commiss ioning, 1 80 se conds tim eout, rep eat t his step.
Step 4: Th ere shall b e indicat ion
L
12V/24V CV PSU
INPU T
N
G
V+
V-
OUTP UT
Max . 20A inpu t
DC INPUT
ZigBe e LED Con troll er
Zigbee
Remote
< 10cm
Input Vol tage DC 1 2-24V Output C urren t 4A/CH Max Powe r 48-96 W/CH
Ta:-20-+ 50
3
1 2
ON
1 2
3
DIM CCT RGBW RGB+CC T
Prog.
1- R- R-
2- G- G -
3- B- B-
LED OUTP UT
4-
5-
WW-
CW-
WW-
W-
WW-
CW-
NCNC
CW-
Step 2: Br ing t he remote o r touch pan el within 1 0cm o f the light ing devic e.
Step 3: Se t the r emote or to uch panel i nto Touch Res et proced ure to rese t the
device , ple ase refer t o corresp onding re mot e or touch pa nel manua l to le arn how.
Note: Ma ke su re the devi ce alread y added to a ne two rk, the rem ote added t o the s ame one or no t added to an y networ k.
on the rem ote a nd connec ted
light fl ash es 3 times fo r
AC Pow er
50/6 0Hz
succes sfu l reset.
V+ V+ R- R-
G- G­B- B-
V+ V+ WW- WW ­CW- CW -
RGB LED S trip
CCT LED S trip
8. Find and Bind Mode
Step 1: Sh ort p ress “Pro g.” butto n 3 times (Or r e-p ower on the d evice (in iti ator node ) 3 times) to s tart Find a nd Bi nd
mode (co nne cted ligh t flashes s lowly) to f ind a nd bind tar get node, 1 80 se conds tim eout, rep eat the ste p.
L
12V/24V CV PSU
ZigBe e LED Con troll er
Input Vol tage DC 1 2-24V Output C urren t 4A/CH Max Powe r 48-96 W/CH
Ta:-20-+ 50
Prog.
INPU T
N
G
WW-
1- R- R-
2- G- G -
CW-
WW-
3- B- B-
LED OUTP UT
W-
WW-
4-
CW-
5-
CW-
NCNC
AC Pow er
50/6 0Hz
V+ V+ R- R-
G- G­B- B-
V+ V+ WW- WW ­CW- CW -
RGB LED S trip
CCT LED S trip
Zigbee
Remote
Max . 20A inpu t
V+
V-
OUTP UT
DC INPUT
3
1 2
DIM
ON
CCT RGBW RGB+CC T
1 2
3
Step 2: Se t the r emote or to uch panel ( target no de) i nto find an d bind mode , and e nable it
to find an d bin d initiat or, please r efe r to cor res ponding r emote or to uch p anel manu al.
Step 3: Th ere shall b e indicat ion o n the remot e or touch pa nel that it b ind t he device succes sfu lly and can c ontrol it t hen.
Note: Ma ke su re the devi ce and the re mote or tou ch pa nel alrea dy added to t he sa me Zigbee h ub.
9. Learning to a Zigbee Green Power Remote
Step 1: Sh ort p ress “Pro g.” butto n 4 times (Or r e-p ower on the d evice 4 tim es) t o start Lea rning mod e
(conne cte d light fla shes twic e), 180 sec ond s timeout , repeat th e ste p.
Step 3: Co nne cted ligh t will flash tw ice t o indicat e succes sfu l learnin g. The n the remote c an co ntrol the d evice.
RGB LED S trip
CCT LED S trip
Zig bee
Gree n Powe r
Rem ote
V+
12V/24V CV PSU
V-
OUTP UT
Max . 20A inpu t
DC INPUT
ZigBe e LED Con troll er
Input Vol tage DC 1 2-24V Output C urren t 4A/CH Max Powe r 48-96 W/CH
Ta:-20-+ 50
3
1 2
DIM CCT RGBW RGB+CC T
1 2ON3
Step 2: Se t the g reen powe r
remote i nto L earning m ode, please r efe r to its manu al.
L
INPU T
N
G
1- R- R-
WW-
2- G- G -
CW-
3- B- B-
WW-
LED OUTP UT
4-
W-
WW-
Prog.
CW-
5-
NCNC
CW-
AC Pow er
50/6 0Hz
V+ V+ R- R-
G- G­B- B-
V+ V+ WW- WW ­CW- CW -
Note: Ea ch de vice can le arn to
max. 20 zi gbe e green pow er remote .
10. Delete Learning to a Zigbee Green Power Remote
Step 1: Sh ort p ress “Pro g.” butto n 3 times (Or r e-p ower on the d evice 3 tim es) t o start del ete Learn ing mode
(conne cte d light fla shes slow ly), 180 se con ds timeou t, repeat t he st ep.
Step 3: Co nne cted ligh t will flash 4 ti mes t o indicat e succes sfu l deletin g.
RGB LED S trip
CCT LED S trip
Zig bee
Gree n Powe r
Rem ote
L
12V/24V CV PSU
INPU T
N
G
V+
V-
OUTP UT
Max . 20A inpu t
DC INPUT
ZigBe e LED Con troll er
Input Vol tage DC 1 2-24V Output C urren t 4A/CH Max Powe r 48-96 W/CH
Ta:-20-+ 50
3
1 2
DIM
ON
CCT RGBW RGB+CC T
1 2
3
1- R- R-
WW-
2- G- G -
CW-
3- B- B-4-WW-
LED OUTP UT
W-
WW-
Prog.
CW-
5-
NCNC
CW-
Step 2: Se t the p aired gre en power re mote into
Learni ng mo de, pleas e refer to it s man ual.
AC Pow er
50/6 0Hz
V+ V+ R- R-
G- G­B- B-
V+ V+ WW- WW ­CW- CW -
11. Setup a Zigbee Network & Ad d Oth er De vic es to t he Ne two rk (N o Coo rdi nat or Re qui red )
Step 1: Sh ort p ress “Pro g.” butto n 4 times (Or r e-p ower on the d evice 4 tim es) t o enable th e device to s etup a
zigbee n etw ork (conn ected lig ht flashe s twi ce) to disc over and ad d oth er device s, 180 seco nds t imeo ut, r epeat the step .
L
12V/24V CV PSU
ZigBe e LED Con troll er
Input Vol tage DC 1 2-24V Output C urren t 4A/CH Max Powe r 48-96 W/CH
Ta:-20-+ 50
Prog.
INPU T
N
G
1- R- R-
WW-
2- G- G -
CW-
3- B- B-
WW-
LED OUTP UT
4-
W-
WW-
CW-
5-
NCNC
CW-
AC Pow er
50/6 0Hz
V+ V+ R- R-
G- G­B- B-
V+ V+ WW- WW ­CW- CW -
RGB LED S trip
CCT LED S trip
V+
V-
OUTP UT
Zigbee
Remote
Max . 20A inpu t
DC INPUT
3
1 2
DIM CCT RGBW RGB+CC T
1 2ON3
< 10cm TouchLi nk
Zigbee Lighting Device
Step 2: Se t ano ther devi ce or remot e or touch pa nel i nto netwo rk pairin g mod e and pair to t he networ k, refer to their ma nua ls.
Step 3: Pa ir mo re device s and remot es to the net wor k as you woul d like, ref er to t heir manu als. Step 4: Bi nd th e added dev ices and re motes thr oug h Touc hli nk so th at th e devices c an be contr oll ed by the
remote s, re fer to thei r manuals .
Note: 1) E ach a dded devi ce can link a nd be contr oll ed by max. 30 a dded remo tes.
2) Each ad ded r emot e can l ink and con trol max. 3 0 add ed device s.
Wiring D iagram
1) RGB+C CT Mode
Max. 20A in put
1 2ON3
2) RGBW Mo de
Max. 20A in put
1 2ON3
L
V+
12V/24V CV PSU
V-
OUTP UT
DC INP UT
3
1 2
DIM CCT RGBW RGB+ CCT
V+
12V/24V CV PSU
V-
OUTP UT
DC INP UT
3
1 2
DIM CCT RGBW RGB+ CCT
INPU T
N
G
ZigB ee LED Co ntrol ler
Inpu t Voltag e DC 12-2 4V Outp ut Curr ent 4A/ CH Max Po wer 48- 96W/C H
Ta:-20- +50
Prog .
L
INPU T
N
G
ZigB ee LED Co ntrol ler
Inpu t Voltag e DC 12-2 4V Outp ut Curr ent 4A/ CH Max Po wer 48- 96W/C H
Ta:-20- +50
Prog .
WW-
1- R- R -
2- G- G-
CW-
3- B- B-4-WW-
LED OU TPUT
CW-
5-
WW-
1- R- R -
2- G- G-
CW-
3- B- B-
WW-
LED OU TPUT
4-
CW-
5-
AC Po wer
50/ 60Hz
V+ V+ R- R-
G- G­B- B-
WW-
W-
CW-
NCNC
WW-
W-
CW-
NCNC
AC Po wer
50/ 60Hz
V+ V+ WW- W W­CW- C W-
V+ V+ R- R-
G- G­B- B­W- W-
RGB LE D Strip
CCT LE D Strip
RGBW L ED Stri p
12. ZigBee Clusters the device supports are as follows:
Input Cl ust ers
0x0000 : Bas ic 0x0003 : Ide ntify 0x0004 : Gro ups 0 x0005: Sc ene s 0x0006 : On/ off
0x0008 : Lev el Contro l 0x 0300: Col or Contro l 0x0b05 : Diagnos tics
Output C lus ters
0x0019 : OTA
13. OTA
Product Dimension
46.5 mm16 mm
145 mm
3) CCT Mod e
Max. 20A in put
4) DIM Mod e
Max. 20A in put
L
V+
12V/24V CV PSU
V-
OUTP UT
DC INP UT
3
1 2
DIM
ON
CCT RGBW RGB+ CCT
1 2
3
V+
12V/24V CV PSU
V-
OUTP UT
DC INP UT
ZigB ee LED Co ntrol ler
Inpu t Voltag e DC 12-2 4V Outp ut Curr ent 4A/ CH Max Po wer 48- 96W/C H
Ta:-20- +50
3
1 2
DIM CCT RGBW RGB+ CCT
1 2ON3
INPU T
N
G
ZigB ee LED Co ntrol ler
Inpu t Voltag e DC 12-2 4V Outp ut Curr ent 4A/ CH Max Po wer 48- 96W/C H
Ta:-20- +50
Prog .
L
INPU T
N
G
Prog .
LED OU TPUT
WW-
1- R- R -
2- G- G-
CW-
3- B- B-
WW-
LED OU TPUT
4-
CW-
5-
WW-
1- R- R -
2- G- G-
CW-
3- B- B-
WW-
4-
W-
CW-
NCNC
5-
WW-
W-
CW-
NCNC
AC Po wer
50/ 60Hz
V+ V+ WW- W W­CW- C W-
WW-
CW-
AC Po wer
50/ 60Hz
V+ V+ 1- V-
V+ V+ 2- V-
V+ V+ 3- V-
V+ V+ 4- V-
V+ V+ 5- V-
V+ V+ WW- W W­CW- C W-
CCT LE D Strip
CCT LE D Strip
Max. 4 A single c olor LE D strip
Max. 4 A single c olor LE D strip
Max. 4 A single c olor LE D strip
Max. 4 A single c olor LE D strip
Max. 4 A single c olor LE D strip
warning:
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
Loading...