Sunricher SR-ZV9100A-A User Manual

Z-Wave In-Wall Smart Switch SR-ZV9100A-A

Function Introduction

Swit ch inpu t

S

SR-ZV910 0A-A(868. 42MHz)

OM

C

Acti on butt on

(2-w ire wit h No Neut ral out put)
(3-w ire wit h Neutr al outp ut)

Load o utput

Ratin gs :230V ~, 50Hz, MA X:4.8 A ( )

Reset

OUT

Safety & Wa rnings

• DO NOT install with pow er applie d to device .

• DO NOT expose the devic e to moistu re.

Quick Start

How to install:

1

AC 100- 24 0V

LL NN

In-wall Smart

Switch

MAX :2 .4 A ( )

Made in C hi na

AC pow er inpu t

(2-w ire wit h No Neut ral inp ut)
(3-w ire wit h Neutr al inpu t)

• Step 1: power on the Z-Wave In-wa ll Smart switch.

• Step 2: activate inclusion mode on your Z-Wave controller.

• Step 3: activate inclusion mode of the switch by triple p ress the ac tion butt on on the switch. The switch

will be included to Z-Wave network.

Product Description

The in-wall smart switch is a Z-Wave device designed to work with various types o f light sou rces. It ma y be
connected to two-wire or three-wire configurati on so it can op erate wit h or without neutral lead. The switc h
can switch ON/OFF connected light source either thr ough Z-Wave devices or through th e wall swit ch
connected directly to it.

The switch can be included and operated in any Z -Wave network with other Z-Wave certified devices fro m
other manufacturers and/or other applications . All non-ba ttery ope rated nodes within the network will act
as repeaters regardless of vendor to incre ase relia bility of t he network.

The encryption mode that the switch supports is S2 Unau thentic ated. Whe n the switch is being included
into a Z-Wa ve networ k, you can us e your primary controller/gateway to enabl e encrypt ion mode or d isable
encryption. (The primary controller/gateway s hall supp ort encry ption mode configuration). The s witch
supports OTA and can upda te firmwa re wirele ssly.

1

Main Fe atures:

• Compatible with any Z-Wave or Z-Wave+ Cont roller,

• Controlled by Sunricher EasyHome or any ot her Z-Wave controller,

• Soft start function,

• Works with various ty pes of swit ches – mome ntary, toggle, three-way, etc.

• Active element: semiconductor electro nic switc h,

• To be installed in wall switch boxes of dimensi ons allow ing for ins tallation, conforming to provisions of
applicable regulations,

• The Bypass is an extens ion unit.

The switch operates under the following loads:

• Conventional incandescent and HV halog en light so urces

• ELV halogen lamps (wit h electro nic trans formers)

• MLV halogen lamps (wit h ferroma gnetic tr ansformers)

• Compact fluorescent CFL tub e lamps with electronic ballast

• Fluorescent tube lamps with electronic b allast

• Supported light sources (power factor > 0.5) with min imal powe r of 5VA using t he Bypass (depending on
the type of load)

Product Data

Z-Wave Frequency

Input Voltage

Output Voltage

Output Current

868.42 MHz (EU)

AC100-240V

AC100-240V

Resistive load: max. 4.8A

Capacitive/Inductive load: max. 2.4A

Operating temperature

Relative humidity

Dimensions

Installation Guide

Please read carefully the enclosed user ma nual befo re instal lation of the in-wall switch, in order to ensure
an error-free functioning.

0 to 40°C

8% to 80%

45.5x45x20.3mm

ATTENTION: Prior to the assembl y of the prod uct, the vo ltage net work has to be switched OFF and
ensured against re-switching.

Inclusion (adding to a Z-Wave n etwork)

1. Set primary controller/gateway into inclusio n mode (Ple ase refer t o your primary controller ’s manual on
how to turn your controller into inclusion ).

2. Power on the in-wall switch and set it into inc lusion mo de. There are two methods to set the in-wall
switch into inclusion mode:

2

1)Repower on the switch, it will be set into inc lusion mo de automa tically, and waiting to be i ncluded .

2)Tripl e press the a ction button on the switch, it will set the switch into inclu sion mode .

Exclusion (removing from a Z-Wave netw ork)

There are two exclusion methods:

Method 1: Exclusion from the primary controller/g ateway as f ollows:

1. Set th e primary controller/gateway into exclus ion mode (P lease ref er to your primary controllers
manual on how to set your controller into excl usion).

2. Triple press the action button, the switch will be set to e xclusio n mode, and w aiting to be excluded, then
the switch will be excluded from the network .

Method 2: Factory reset the switch will force it to be excluded from a n etwork. ( please re fer to the part
“Factory Reset” of this manual)

Note: Factory reset is not recommended for exclusio n, please u se this pro cedure only if the primary
controller/gateway is missing or other wise inop erable.

Factory Reset

Press and hold down the action button for over 1 0 seconds , the switc h will be res et to factory defaults.

Association

Z-Wave de vices con trol othe r Z-Wave devi ces. The relationship between on e device co ntrolli ng another
device is called association. In order to co ntrol a different device, the controlling device nee ds to maint ain
a list of devices that will receive controll ing comma nds. These lists are called associ ation gro ups and the y
are always related to certain events (e.g. button pre ssed). In c ase the eve nt happens all devices stored in
the respective association group will re ceive a com mon wirel ess command.

Association Groups:

Association

Groups

Group 1

Group

Name

Lifeline

Max

Nodes

5

Description

1. When press and hold down “Reset” button for 10S to reset
the switch, send "Device Reset Locally Not ificati on CC" to
associated devices of this group to report factory re set
information.

2. When load state changes, send "Basic Repo rt CC" to
associated devices of this group.

3. When over temperature is detected, send “Emergen cy
shutoff status" to Lifeline.

Set and unset associations:

(Note: All association information will b e cleared a utomati cally once the switch is excluded from a
network.)

Set association by operating primary con troller /gatewa y to send packets to the switch:

3

The primary controller/gateway sends p ackets to t he switch u sing “Com mand Class ASSOCIATION”

Operating the device

Short press the action button on the switch to switch ON/OFF the loa d.

Node Information Frame

The Node Information Frame is the business card of a Z-Wave device. It contains informat ion about t he
device type and the technical capabiliti es. The inclusion and exclusion of the device i s confirm ed by
sending out a Node Information Frame. Besi de this it ma y be needed f or certai n network operations to
send out a Node Information Frame.

How to send out Node Information Frame:

When the switch is set to inclusion/exclusion mode ag ain, it wil l send out Node Information Frame, there
are 2 kinds of operation as follows:

1. triple press the action button, the switch will be set t o inclusi on/excl usion mode, then send out Node
Information Frame.

2. When the switch is under inclusion mode, th ere are two k inds of ope ration:

1) Triple press inclusion/exclusion but ton, the sw itch will b e set to inclusion mode again, and send out
Node Information Frame.

2) Power off and power on t he switch , it will be se t to inclusion mode automatically, and send ou t Node
Information Frame.

Technical Data

Wireless Range

SDK

Explorer Frame Support

Device Type

Generic Device Class

Specific Device Class

Role Type

Routing

up to 100 m outside, on average up to 40 m inside buildings

6.71.03

Yes

on/off Power Switch

GENERIC_TYPE_SWITCH_BINARY

SPECIFIC_TYPE_POWER_SWITCH_BINARY

Always On Slave (AOS)

Yes

SUPPORTED COMMAND CLASS

Node Info

COMMAND_CLASS_ZWAVEPLUS_INFO

Security Command Supported Report

COMMAND_CLASS_MANUFACTURER_S

V2 V2

PECIFIC

4

COMMAND_CLASS_TRANSPORT_SERVICE

V2

COMMAND_CLASS_VERSION

V2

COMMAND_CLASS_SECURITY

COMMAND_CLASS_SECURITY_2

COMMAND_CLASS_SUPERVIS ION

V1

V1

V1

COMMAND_CLASS_SWITCH_BINARY

COMMAND_CLASS_SCENE_ACTIVATION

OMMAND_CLASS_SCENE_ACTUATOR_C

ONF

COMMAND_CLASS_NOTIFICATION

COMMAND_CLASS_CONFIGURATION

COMMAND_CLASS_ASSOCIATI ON_GRP

_INFO

COMMAND_CLASS_ASSOCIATI ON

COMMAND_CLASS_FIRMWAR E_UPDATE_

MD

COMMAND_CLASS_POWERLEVEL

COMMAND_CLASS_DEVICE_RESET_LOC

ALLY

V1

V1

V1

V8

V1

V3

V2

V4

V1

V1

Notification Command Class

The switch supports Emergency shutoff, when inside temperature is over 90℃ and
detected by the built-in thermistance, the switch will send out Emergency shutoff status
to Lifeline.

Notification Type

System (0x09)

Emergency shutoff status (0x07)

Notification

Configuration Command Class

Parameter

Size Description Default Value

Info: Saving load state before power failure

0 － shutoff load

2 1 2

1 － turn on load

2 － save load state before power failure

5

Info: Enable/disable to send the basic report to
the Lifeline when the load state changed

3

1 1

0 － Disable to send Basic report

1 － Enable to send Basic report

Added to and removed from a network through
external switch (when enables this function,
triple press the external switch within 1.5
seconds to be added to or removed from a

4

1 1

network)

0 - disable

1 - enable

External switch type

0 – Push button switch

5

1 0

1 – normal on/off switch

2 – 3-way switch

Wiring Diagram

Notes for the diagrams:
L - termi nal for live lead
N - terminal for neutral lead
Out - output terminal of the switch (controlling conn ected lig ht source )
S1 - terminal for switch (has the option of entering the de vice in inc lusion/ exclusion mode)
COM - terminal for grounding to the switch connected to t he switch

Compatible Load Types

Supported load types

Resistive loads

Conventional incandescent and haloge n light
sources

Capacitive loads

Fluorescent tube lamp (compact / with
electronic ballast), electronic transformer, L ED

100-240V~

Max. 4.8A

Max. 2.4A

Induc tive loads

Ferromagnetic transformers

Max. 2.4A

6

(1) 2-Wire Connection With No Neutral Lead

PUS H

1

AC 10 0-240 V

LL NN

In-wall Smart

Switch

MAX :2.4A ( )

Mad e in Chin a

S

SR-ZV9100A- A(868.42MHz)

OM

C

Rat ings: 230V~ ,50Hz ,MAX: 4.8A ( )

Res et

OUT

NOTE: Switch connected to the S1 terminal
activates the basic functionality of the switch
(turning the light on/off) and s tarts the
inclusion/exclusion mode (Add/Remo ve).

Bypa ss

Live

Neutral

The Bypass is a device designed to work with the i n-wall sm art switc h. It shoul d be used in case of

connecting LED bulbs or energy saving comp act fluor escent la mps. The Bypass prevent s flicker ing of the

LED lights and glowing of the turned off comp act fluorescent lamps. In the case of 2-wire connection , the

Bypass allows to reduce minimum power of loa d require d by the swit ch for corr ect operation. The Bypa ss

provides powering of the switch in case of con trollin g the low loa ds of minimum power down to 5VA (for

cosφ>0.5).

(2) 3-Wire Connection With Neutral Lead

PUS H

1

AC 10 0-240 V

LL NN

In-wall Smart

S

SR-ZV9100A- A(868.42MHz)

M

O

C

Rat ings: 230V~ ,50Hz ,MAX: 4.8A ( )

Res et

OUT

Live

Neutral

Switch

MAX :2.4A ( )

Mad e in Chin a

NOTE: Switch connected to the S1 terminal
activates the basic functionality of the switch
(turning the light on/off) and s tarts the
inclusion/exclusion mode (Add/Remo ve).

7

(3) 3-Way S witch Con nection

3-Way Switch ( SPDT)

3-Way Switch ( SPDT)

(4) Momentary Wall S witch Connection

AC 10 0-240 V

LL NN

In-wall Smart

Switch

MAX :2.4A ( )

Mad e in Chin a

COM

Rat ings: 230V~ ,50Hz ,MAX: 4.8A ( )

OUT

S1

SR-ZV9100A- A(868.42MHz)

M

O

C

Rat ings: 230V~ ,50Hz ,MAX: 4.8A ( )

Res et

OUT

AC 10 0-240 V

LL NN

In-wall Smart

Switch

MAX :2.4A ( )

Mad e in Chin a

S1

SR-ZV9100A- A(868.42MHz)

Res et

8