Remote control
r
Sunpery
TM
Intelligent Window Covering Automation Systems
Instruction Manual
Remote control C222
Sunpery remote C222 is a handy tool to be used for operating Sunpery window coveri ng automation
systems. It works in both drapery and roller systems and controls up to 6 channels drapery systems or 6
channels of roller systems. Multiple motors can be grouped and controlled by each channel.
1. Commissioning
In first time of using the remote, the motor needs to
recognize the remote. Press channel selecting button, one
of channel indicating digits will illuminate, keep press the
channel button until the desired channel digit turns up. The
motor needs to be powered off for 1 minute, Then power on
again. Within 90 seconds after power on, press and hold
OPEN and CLOSE buttons simultaneously. The selected
channel number will turn up with slow flash. The motor react
with a movement to indicate motor receiving the signal from
the remote and confirm communication in between has
been established. Test run by press OPEN or CLOSE
button.
Limits setting
Intermediate
control buttons
A
Cente
B
2. Changing travel Direction
The buttons on the remote control should provide indication
for the direction of movements of an automation system. If
they are not, for example, when press OPEN button the
blinds goes down, you may need to change the direction.
To change direction, motor is to be power-off for 1 minute, then power on again. Press and hold button A
and button B simultaneously, the digit flash slowly, motor reacts with jogs to confirm change made. This
can only be done within 2 minutes of the motor gets connected to power. Test run by press OPEN or
CLOSE button.
3. Limit setting
No limit setting is required for Sunpery standard DC drapery motors, only Sunpery encoded motors,
such as electronic motors for roller blinds and AC drapery motors require limit settings. To enter into limit
setting mode, press and hold button A and button B buttons simultaneously during normal operating
mode which is after initial 2 minutes of power up. The channel digit flashes slowly, and motor react with
jogs. Press OPEN or CLOSE button to move the blinds to the position where you wish to set the limit.
Press button A, and motor jogs to confirm the first limit has been set. Press CLOSE or OPEN button to
move the blinds to the other position where you wish to set the other limit. Press button B, and motor
jogs to confirm the other limit has been set and out of limit setting mode.
1
OPEN
STOP
CLOSE
Channel
select
Remote control
4. Intermediate stop setting
No intermediate stop setting is required for Sunpery standard DC drapery motors, only Sunpery
encoded motors, such as electronic motors for roller blinds and AC drapery motors require have
intermediate stop feature. There are up to three intermediate stops can be set with Sunpery encode
motors. If only end limits were set, the motor will automatically with intermediate stops at 25%, 50% and
75% by its factory settings.
Setting intermediate stops needs to be down during the time of setting end limits. As in step 3, get into
limit setting mode by press and hold button A and button B simultaneously . After reaction from the motor,
move the blinds by press OPEN or CLOSE button to where you want to set first limit. Press button A,
and motor reacts to confirm the first limit has set. Then move the blinds to the position where you want to
set the first intermediate stop, press button A and button Center simultaneously. Motor reacts to confirm
the first intermediate stop has been set. Further move the blinds to the position where you want for the
central intermediate stop, press button Center and motor reacts to confirm the center intermediate stop
setting. Further moving the blinds to where you want for the next intermediate stop, press button B and
button Center simultaneously. Motor reacts to confirm the last intermediate stop has been set. Further
move the blinds to where the end limit should be, press button B, motor reacts by jogs to confirm the last
limit has been set and out of limit setting mode.
5. Operating
To operate, simply press OPEN or CLOSE for driving the window coverings, the system will be running
until meets its end of travel span. If it is a encode motor, press button A will drive the system to the first
intermediate stop. Press button Center will move the system to the center intermediate stop. Press
button B will move it to the third intermediate stop.
6. Delete channel settings at the motor
Select the channel that commending the motor to which you want to cancel the channel setting. Press
and hold OPEN and STOP buttons, motor react with jogs. The particular channel on the remote will
deleted from the motor , therefore no long operate the motor. If press and hold STOP and CLOSE buttons,
motor reacts with jogs, all the channel settings on the motor will be deleted if the motor has been
programmed with more than one remote or more than one channel on the same remote. To test
effectiveness of the deleting, simply press any of the action buttons, OPEN, CLOSE, intermediate
buttons . Motor should not move.
7. Replacing battery
The remote is powered by two Li-ion button batteries,
Model number: CR24300. The battery lasts for over two
years under normal operating condition. When digits “1”
and “6” turn up at the same time, it means the batteries
are flat, time to replace. The battery is a standard type.
You can easily find it in shops. Open the remote case by
pushing top lid to up direction. After top lid get moved in
about 5mm, it can be removed and the battery can be
seen. Simply replace the old battery with new ones, then
2
Remote control
put the top lid back.
8. Wall bracket
A wall bracket is specially designed for when you need to place the remote on the wall. Fix the metal part
to the wall by two head-sink screws. Slide the plastic part on to the metal part. Place the handset onto
the wall bracket.
3
Remote control
The flowchart -------programming Sunpery standard DC drapery system from the remote
Warning: In order to prevent damage, never start programming with the lead carrier at very end of rail.
ST ART
Select the required channel on
remote handset
Connect motor to power supply,
e.g. mains, adaptor, sola r penal
Check Power
Supply
Power off the motor for 1
min and power on again
Press and Hold the OPEN
& CLOSE Buttons on the
Transmitter within 90s
Press and hold the OPEN &
CLOSE within 90s of power
connected
No
The Motor
Jogs?
Yes
Press OPEN or CLOSE
Buttons to Check Motor
Direction
No
Is the Direction
Correct?
Yes
Motor Jogs and Direction
is Reversed
Testing run the motor by
Press and Hold OPEN or
CLOSE Button
END
4
jog
Remote control
The flowchart -------programming a Sunpery encode motor from the remote
Warning: In order to prevent damage, never start programming with the system at its extreme end..
START
Move the motor to your
desired first intermediate
stop position
Press and hold the A and
Center buttons until
motor jogs
Move the motor to your
desired center
intermediate stop
Press and hold Center
buttons until motor jogs
Check Power
Supply
Select the required
channel on remote
handset
Connect motor to power
supply
Press and hold the OPEN &
CLOSE within 90 seconds of
power connected
Press and hold A & B
buttons within 90
seconds after power on
supplied to motor
Motor jogs and
direction is reversed
No
No
press and hold OPEN or
The motor
jogs?
Yes
Press OPEN or CLOSE
buttons to check motor
direction
Is the direction
correct?
Yes
Press and hold A & B
buttons till motor jogs
Move the motor to your
desired end limit by
CLOSE button
Move the motor to your
desired last intermediate
stop position
Press and hold B &
Center buttons until
motor jogs
Move the motor to your
desired the final limit
Press and hold B
button until motor jogs
Limit setting complete
Check if motor moves
automatically to desired
end limits by press
OPEN or CLOSE
Check if motor moves
Press and hold Abutton
until motor
Want to set
intermediate
stop ?
5
s
Yes
No
automatically to desired
intermediate stops by
press any intermediate
buttons
END
FCC ID: VXC-C222-9120
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for
help.
Loading...