Sunpentown SL824T5 User Manual

LAMP INSTALLATION

When table or surface thickness is less
than 2 cm, please use the insole to
increase stability.

Add the Height-Increase
Insole when surface
thickness is less than 2cm.

Do not install lamp:

Limited surface
space for clamp

On a pole or
uneven surface

Surface that is too
thin or fragile to
support lamp

Horizontally

SL-824T5

T-5 Fluorescent Task Lamp

Your Guarantee

If this product is found to be faulty as a result of faulty materials or workmanship
within one year from date of purchase, it will be repaired free of charge.

This guarantee is subject to the following terms:

Sunpentown must be notified of the fault.
Proof of purchase must be presented to Sunpentown’s nominated representative.
The warranty will be void if the product if modified, misused or repaired by an

unauthorized person.

The warranty after repair will not be extended beyond the original one-year period.
All replacement parts will be new or reconditioned.
Parts, which are replaced, become the property of Sunpentown.
The warranty applies for the use of the product in the USA only.

What is NOT COVERED:

Warranty does not include freight charges.
Incidental or consequential damage caused by possible defects with this product.
Damage to product caused by improper power supply voltage, accident, fire,

floods or acts of nature.

Thank you for your purchase, please read all instructions before using.Please keep this instruction
manual in a safe place for future reference.

Ver.01 DRH-R-84-12

Failure of product resulting from unauthorized modifications to the product.
Improper installation or failure to perform the necessary maintenance.

This GUARANTEE is in addition to your Statutory Rights

SUNPENTOWN INTERNATIONAL INC.

14625 Clark Ave. City of Industry, CA 91745

Tel: [phone]

[e-mail]

www.sunpentown.com

PARTS IDENTIFICATION

Lamp Shade



If loose, use a screwdriver to tighten.

IMPORTANT SAFEGUARDS

Fixture
When installing
make sure “click”
is heard.

Aluminum arm

LidLight bulb

Bottom cover

Dimmer control

Power switch

Adjustment screw



If loose, use a screwdriver to tighten screws

(use of other tools may cause damage)

Clamp

height increased insole

BULB INSTALLATION / REPLACEMENT INSTRUCTIONS
Make sure lamp is powered off and unplugged from power source.
Wait until bulb is cool enough to handle. Bulb is hot immediately
after powering off.

Removal

1. Turn bulb 90 degrees and remove from socket .

Installation

Align base of bulb to notch on the socket. Turn bulb until a 1.
“click” is heard.

Note: Handle with care, do not drop.

Do not replace anything other than the bulb.
Only replace with HO-24W bulb

Fixture
When installing
make sure “click”
is heard.

Use a coin or flathead
screwdriver

Attention

Do not use excessive force
when securing

Socket

Bulb

Notch

Teminal

IMPORTANT SAFEGUARDS

Do not operate this lamp near a water source to avoid electric shock.
Do not dismantle.
Do not use with power supply other than 120V~60Hz.
Do not operate lamp in close proximity to flammable or combustible vapors, such

as aerosol spray, or where oxygen is being administered.

Do not cut or shorten the power cord.
Always unplug lamp before performing bulb installation, bulb replacement or

maintenance.

This product may cause interference with radios, cordless telephones or devices
that use a wireless remote control, such as televisions. If interference occurs, move
the product away from the device, plug the device or lamp in a different outlet or
move the lamp out of the line of the remote control receiver.

Unplug the lamp during lightning storms or when unused for extended period of time.
All moisture should be properly wiped away and dried prior to use.
Do not touch bulb when lamp is on or shortly after powering off. May cause burns.
Dispose of bulbs per local regulations.

SPECIFICATIONS

Power Consumption

Model

Power Supply

Dimension

Weight

Replacement Bulb

SL-824 T5

24W

120V / 60Hz

Approx. 22.4x27.56x19.67 (in)

3.17 lbs

HO-27W

MAINTENANCE

Before cleaning, make sure lamp is powered off and unplugged. Allow sufficient time
for the bulb to cool down.

Periodically wipe the lamp with a soft damp cloth. Use a mild non-abrasive cleaner if
needed.

All liquid should be properly wiped away and dried prior to restoring power.
Do not use solvents or abrasive cleaners.