Instruction Manual
SD-2224DS
SD-2224DW
Dishwasher
Read this Manual
Safety Information
Grounding Instruction............................1
Safety Instructions.................................1
Dear Customer,
Please read this manual thoroughly before use.
Understanding the unit will help you use and maintain
the dishwasher properly.
Please keep in a safe place for future reference.
Pass it on to any subsequent owner of the appliance.
For your safety, the information detailed in this manual
should be followed. Improper use/handling can cause
serious damage to the appliance and/or to the user,
including but not limited to fire, explosion, electric shock,
resulting in personal injury or death.
Before Calling for Service
Review the section on Troubleshooting Tips - it may
help you solve some common issues.
If you can not resolve the troubles by yourself ,
please ask for the help of professional technicians.
Parts Identification
Front & Back View.................................2
Accessories...........................................2
Installation
Unpacking.............................................3
Positioning.............................................3
Electrical Requirements........................3
Connecting the Dishwasher...............4-5
Disconnecting the Dishwasher..............5
Operating Instructions
Checklist................................................6
Control Panel.........................................6
Loading the Dishwasher........................7
Cutlery Basket.......................................8
Detergent Dispenser..............................9
Rinse Aid Dispenser............................10
Wash Cycle Table................................11
Starting a Wash Cycle.........................11
Changing the Wash Program..............12
Forgot to Add a Dish?..........................12
At the End of the Wash Cycle..............12
Maintenance
Filter System.......................................13
Filter Assembly....................................13
Cleaning the Filters.............................13
Cleaning the Dishwasher....................14
Cleaning the Door...............................14
Cleaning the Spray Arm......................14
Protect Against Freezing.....................14
Keeping Your Dishwasher in Shape....15
NOTE:
The manufacturer, following a policy of constant
development and updating of the product, may
make modifications without giving prior notice.
Troubleshooting.......................16-17
Error Indications...........................17
Technical Information.................18
Warranty
IMPORTANT SAFETY INFORMATION
READ ALL INSTRUCTIONS BEFORE USING
WARNING!
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of a
malfunction or breakdown, grounding will reduce
the risk of electric shock by providing a path of
least resistance of electric current. This appliance
is equipped with a cord having an equipmentgrounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet
that is installed and grounded in accordance with
all local codes and ordinances.
WARNING! PROPER USE
Use this appliance only for its intended purpose
as described in this manual.
This appliance is not intended for use by children.
Do not abuse, sit on, or stand on the door or dish
rack of the dishwasher.
Do not touch the heating element during or
immediately after use.
(This instruction is only applicable to machines
with a visibal heating element.)
Do not operate your dishwasher unless all
enclosure panels are properly in place. Open
the door very carefully if the dishwasher is
operating, there is a risk of water squirting out.
Do not place any heavy objects or stand on the
door when it is open. The appliance could tip
forward.
When loading items to be washed:
1) Locate sharp items so that they are not likely
to damage the door seal;
2) Wa rn in g: K ni ve s an d ot he r ut en si ls w it h
sharp points must be loaded in the basket
with their points down or placed in a
horizontal position.
Check that the detergent receptible is empty
after completion of the wash cycle.
Do not wash plastic items unless they are marked
dishwasher safe or the equivalent. For plastic it ems
notm
manufacturer’s recommendations.
Use only detergent and rinse additives
designed for an automatic dishwasher.
Never use soap, laundry detergent, or hand
washing detergent in your dishwasher. Keep
these products out of the reach of children.
When using your dishwasher, follow the precautions listed below:
WARNING!
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
Check with a qualified electrician or service
representative if you are in doubt whether the
appliance is properly grounded. Do not modify the
plug provided with the appliance; If it does not fit the
outlet. Have a proper outlet installed by a qualified
electrician.
Keep children away from detergent and rinse aid, keep
children away from the open door of the dishwasher,
there could still be some detergent left inside.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
Children should be supervised to ensure that they do
not play with the appliance.
arked as dishwasher safe, refer to the
concerning use of the appliance by a person responsible
for their safety.
Dishwasher detergents are strongly alkaline, they
can be extremely dangerous if swallowed. Avoid
contact with skin and eyes and keep children away
from the dishwasher when the door is open.
The door should not be left in the open position
since this could present a tripping hazard.
If the supply cord is damaged, it must be replaced
by the manufacturer or its service agent or a
similarly qualified person in order to avoid a
hazard.
Remove the door before discarding an old dishwasher.
Please dispose of packing materials properly.
Use the dishwasher only for its intended function.
During installation, the power supply must not
be excessively or dangerously bent or flattened.
Do not tamper with controls.
Use new set of hoses to connect this appliance to the
water mains. Do not reuse old hose sets.
The maximum number of place settings to be
washed is 6.
The maximum permissible inlet water pressure is
1Mpa.
The minimum permissible inlet water pressure is
0.04Mpa.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY
SAVE THESE INSTRUCTIONS
1
PARTS IDENTIFICATION
ACCESSORIES
Your dishwash er comes equipped with a 'quick connect' assembly (includes inlet a nd drain hose ). The
fauc et adapter mu st be install ed on the faucet before you can connect the dishwasher. This adapter is
inst alled on the Qu ick Connect . The fa ucet adapte r is compatib le with faucets inclusive of either male
(out side) or fema le (inside) t hreaded faucet connections.
WARNING!
In order t o av oid water pressure build up, pl ea se turn off th e faucet after each use.
2
INSTALLATION
Attention:
The installation of the pipes
and electrical equipments
should be done by professionals.
Warning
Electrical Shoc k Ha za rd
Disconnect elec tr ic al power before
installing dish wa sh er.
Failure to do so can re su lt i n death
or electrical sho ck .
Unpacking
Have at least two people to move and install the dishwasher to prevent personal injuries.
Remove all packaging materials: shipping tape, foam pieces, etc. before use. Do not use
sharp instruments, rubbing alcohol, flammable fluids or abrasive cleaners. Check and
make sure all parts necessary for installation are included. If parts are missing, please
contact Sunpentown at 1-800-330-0388. The dishwasher must be placed on a level and
flat surface that can support the weight when the dishwasher is fully loaded.
Positioning
This dishwasher is designed for countertop installation. The dishwasher is equipped
with water supply and drain hoses that can be positioned to the right or the left
to facilitate proper installation. Make sure water supply/faucet connection is within
reach of the inlet and drain hose assembly (5 ft).
Electrical Requirements
Read all safety precautions listed at the beginning of the manual. Make sure the
electrical outlet is within reach of the power supply cord (4.5 ft). It is recommended
to not use receptacles that can be turned on/off by a switch or pull chain.
Refer to the rating label and be sure the voltage and frequency corresponds to the
power supply. Use a dedicated circuit that is rated for 10 amps.
The dishwasher is equipped with a power supply cord with a 3-prong grounding plug.
The cord must be plugged into a mating 3-pronged wall receptacle. If a mating wall
receptacle is not available, it is the personal responsibility of the customer to have a
properly grounded, 3-pring wall receptacle installed by a certified electrician.
WARNING!
· DO NOT use an extension cord or an adapter plug with this appliance.
· DO NOT, under any circumstances, cut or remove the ground-prong.
· Improper connection of the connection of the equipment grounding conductor can result in
electric shock.
· Check with a qualied electrician or service representative if you are in doubt whether
the appliance is properly grounded.
3
Connecting the Dishwasher
Faucet Adapter & Washer
Your dishwasher is equipped with a Faucet Adapter (installed on the Quick Connect),
Quick Connect, Drain and Inlet Hose. The faucet adapter must be installed on the
faucet before connecting the dishwasher.
Remove the Faucet Adatper by pulling back the locking collar
on the Quick Connect; while pulling the Faucet Adapter in the
opposite direction.
Locking Collar
Installing Quick Connect to faucet
The Faucet Adapter is compatible with either female
(inside) or male (outside) threaded faucet connections:
· If your faucet is “female” type, both rubber washers
must be installed inside the faucet adapter.
· If your faucet is “male” type, use only one rubber
washer. Remove the second rubber washer.
4
1. Screw the Faucet Adapter onto (or into) the faucet. Check for leaks (use Teon or plumbers
tape to eliminate any leaks if necessary).
2. Connect the six-sided connection of the Drain Hose to the dishwasher’s drain port, located
on back of the dishwasher cabinet. To avoid damage to threads, do not over-tighten.
3. Connect the star-shaped connection of the Inlet Hose to the dishwasher’s inlet port, located
on the back of the dishwasher cabinet. Do not over-tighten.
4. Connect the circular connection of the Drain Hose to the longer (bottom) male connection
on the Quick Connect.
5. Connect the circular connection of the Inlet Hose to the shorter (top) male connection on the
Quick Connect.
6. Attach the Quick Connect assembly onto the Faucet Adapter - pull down on the locking collar,
while pushing the Quick Connect assembly upwards onto the Faucet Adapter.
7. Release the locking collar when the Quick Connect Assembly snaps onto the Faucet Adapter.
Verify connection is secure.
8. Slowly turn on the water line and check for any signs of water leak at all connections. If leaks
are located, immediately turn off the water supply and repair hose connections.
IMPORTANT
· Once you turn on the water supply (even if turned off immediately), the inlet hose will be pressurized.
· To relieve the water pressure (make sure water supply is turned off): press and hold the red
pressure relief button on the Quick Connect until the ow of water stops.
WARNING
FAILURE TO RELIEVE WATER PRESSURE, BEFORE DISCONNECTING THE QUICK-CONNECT
FROM THE FAUCET, WILL RESULT IN BACK-PRESSURE OVER-SPRAY. THE TEMPERATURE
OF INCOMING WATER CAN BE VERY HOT, AND BACK-PRESSURE OVER-SPRAY CAN CAUSE
SEVERE BURNS AND/OR SCALDING.
DANGER
DO NOT LET CHILDREN DISCONNECT THE DISHWASHER; CLOSE SUPERVISION OF
CHILDREN IS ALWAYS IMPORTANT AROUND APPLIANCES.
NOTE:
Hard water conditions will adversely affect the washing performance of your dishwasher. Hard
water conditions will also contribute to 'lime' (white lm substance) deposits and/or 'scaling' on the
stainless steel surface of the dishwasher tub and heater element, located in the sump underneath
the removable lter screen. To assist in minimizing these conditions, it is recommended to
periodically operate/rinse the inside of the dishwasher (empty) using 1 cup of white vinegar at least
once a week.
Disconnecting the Dishwasher
1. Turn off water supply at the faucet.
2. Disconnect the power supply cord.
3. Release water pressure inside the inlet hose. Press and hold the red Pressure Relief Valve until
the ow of water stops.
4. Disconnect the Quick Connect assembly by pulling down on the locking collar and release from
Faucet Adapter.
5
OPERATING INSTRUCTIONS
IMPORTANT
To get the best performance from your dishwa sher, read all o perating instructions.
Checklist
The following things should be checked before using the dishwasher:
The dishwasher is level
Water (faucet) is turned on
There are no leaks at the drain and inlet ports
The unit’s power plug is connected to a grounded outlet
Power is turned on
There are no kinks in the drain and inlet hoses
All packaging and printed materials are removed from the dishwasher
Attention:
After installation, please make sure to keep this manual.
Control Panel
Power Button: Press to turn the unit ON/OFF
1
2
Delay Button: Press to delay start of wash cycle
Display Screen: Shows remaining time or current running state
3
Rinse-Aid Warning Indicator: Indicates the rinse aid needs to be refilled
4
Water Supply Indicator: Indicates no water supply (faucet is not turned on)
5
Wash Program Selector: Press to select desired wash program
6
Star t/Pause Button: Press to START or PAUSE the dishwasher
7
Wash Program Indicators: Indicates selected wash program
8
6
Loading the Dishwasher
A properly loaded dishwasher is key for optimal performance. Never overll the dishwasher as
it can reduce the unit’s efciency. Improper placement of items can also affect the dishwasher’s
performance. Position the dishes and utensils so they are secure during the wash cycle and will
not be moved by sprayed water.
This dishwasher is designed to hold 6 place settings:
6 cups
6 glasses
2 serving dish/bowls
6 saucers
6 bowls
1 large platter
6 dinner plates
6 dessert/bread plates
6 sets of utensils
Plate racks
The basket is fitted with plate racks which
can be stowed horizontal if required.
7
Cutler y Basket
Flatware should be placed in the cutlery basket with handles at the bottom. Knives and
other sharp utensils should be placed with handles up, but make sure the tips do not
extend through the bottom. If the rack has side baskets, spoons should be loaded
individually into appropriate slots. Longer utensils should be placed horizontally on
the cup shelf.
WARNING!
Do not l et any item exten d through botto m.
Alwa ys load sharp ute nsils with the sh arp point down!
Be sur e similar piece s do not nest toget her.
FOR BEST PERFORMANCE:
· Scrape off food particles before loading.
· Soften remnants of burnt food in pans
· Place cups, glasses, pots/pans face down.
· Curved items, or those with recesses, should be loaded at a slant so water can run off.
· Allow sufficient space between items to allow water and detergent to reach each surface.
· Ensure glasses and stemware are secure and balanced.
· Ensure breakable items are not sitting on metal cutlery which can ship the dishes.
· Do not overload the dishwasher.
WARNING
· To prevent damage, do not remove glass and cutlery from the dishwasher immediately
after end of program. Allow the dishware to return to room temperature.
The following items are not suitable for wash in the dishwasher:
· Cutlery with wooden, horn china or mother-of-pearl handles and wooden platters
· Plastic items that are not heat resistant.
· Older cutlery with glued parts that are not temperature resistant.
· Bonded cutlery items or dishes
· Pewter or copper items
· Crystal glass
· Steel items subject to rusting
· Very small items as they may fall out the basket
· Items made from synthetic fibers
The following are of limited suitability:
· Silver and aluminum - tends to discolor after washing
· Glazed patterns may fade
8
Detergent Dispenser
Use only detergent specifically made for use with dishwashers. Keep detergent fresh and
dry. Do not put powder detergent into the dispenser until you are ready to wash dishes,
which can get damp and not dissolve properly.
The hardness of your water will affect the amount of detergent to use. With hard water,
extra detergent is need to remove deposits left by excessive minerals. Soft water requires
less detergent (too much detergent with soft water can cause permanent cloudiness of
glassware)
DETERGENT TABLETS
Detergent tablets of different brands dissolve at different speeds. For this reason, some
tablets cannot dissolve and develop their full cleaning power during short programs.
If using a detergent tablet, please select a long program to ensure complete removal of
detergent residuals.
ADDING DETERGENT
The dispenser must be filled before start of each wash cycle. Your dishwasher uses less
detergent and rinse aid then conventional dishwasher. Generally, only one tablespoon
of detergent is needed for a normal wash load. After filling, close lid and press until it
locks in place.
WARNING!
Dishwasher detergent is corrosive! Take care to keep it out of reach of children.
Main detergent chamber
A
(holds up to 15 grams of detergent)
Tablet or pre-wash cycle detergent chamber.
B
If dishes are heavily soiled, add additional detergent
here, which will be released during pre-wash phase.
(holds up to 25 grams of detergent)
NOTE
· Please observe manufacturers dosing and storage
recommendations as stated on detergent packaging.
· NEVER USE HAND DISH DETERGENT!
9
Rinse Aid Dispenser
The rinse aid is released during the final rinse to help remove spots and prevent film
build-up on your dishes, flatware and cookware. Also improves drying by allowing water
to sheet off the dishes. Your dishwasher is designed to use liquid rinse aids.
ADDING RINSE AID
The rinse aid dispenser is located inside the door, next to the detergent dispenser.
1. Make sure the dishwasher door is fully open.
2. Turn the dispenser cap counter-clockwise to the left arrow. Lift and remove cap.
3. Add rinse aid until the indicator window turns completely black - be careful not to overfill.
(The capacity of the rinse aid container is approx. 3.7 oz.)
4. Replace cap by aligning to the “open” (left) arrow and turn clockwise to close.
5. Clean up any spilled rinse aid to avoid excessive foaming in the next wash.
REFILLING RINSE AID
When the rinse aid container is full, the Rinse Aid
Indicator (next to the cap) will be dark. As rinse aid
Rinse- Ai d in dicator
diminishes, the size of the dark dot will also reduce.
Do not let the rinse aid fall below 1/4 full:
Full
3/4 full
1/2 full
1/4 full - time to refill to eliminate spotting
Empty
Attention!
Only use branded rinse aid for the dishwasher. Never fill the rinse aid dispenser with
other substances such as liquid detergent.
ADJUSTING RINSE AID DISPENSER
Adjust in g le ver
The rinse aid dispenser has four settings. It is recommended
to start with the dispenser set at “3”. If spots or poor drying
occurs, increase the setting to “4”. If there are sticky
whitish stains on dishes or bluish film on glassware, reduce
the setting to “2” or “1”.
10
Wach Cycle Table
NOTE:
( )
= Rinse-Aid required
Program
Heavy
Normal
Light
Mini Party
Cycle Selection
Information
For the heaviest soiled loads,
such as pots,pans,casserole
dishes and dishes that have
been sitting with dried food
on them for a while.
For normally soiled loads,
such as pots, plates,glasses
and lightly soiled pans.
standard daily cycle.
For lightly soiled loads,such
as plates,glasses,bowls and
lightly soiled pans.
For lightly soiled loads, such
as glasses, crystal and
fine china.
Description
of Cycle
Pre-wash
Pre-wash(122°F)
Was h (1 31 °F )
Was h (1 22 °F )
Rinse
Rinse (154°F)
Drying
Pre-wash
Pre-wash
Was h (1 25 °F )
Rinse
Rinse (149°F)
Drying
Pre-wash
Pre-wash (122°F)
Was h (1 22 °F )
Rinse
Rinse (140°F)
Drying
Pre-wash
Was h( 113°F)
Rinse
Rinse (122°F)
Drying
Detergent
pre/main
18g
18g
18g
15 g.
Running
time(min)
100
110
75
20
Energy
(Kwh)
0.47
0.38
0.32
0.22
Water
(l)
14.5
10.8
12
7
Rinse
Aid
Pre-wash
Main-wash
Pre-wash
Pre-wash(122°F)
Was h (1 22 °F )
Rinse
Rinse(131°F)
Pre-wash
/
15 g.
/
24
45
10
0.02
0.29
0.01
5
12
2.5
Rinse
Speed
Soak
For non-greasy dishes that
just need to be rinsed
A shorter wash for lightly
soiled loads that do not
need drying.
To rinse dishes that you
plan to wash later.
Star ting A Wash Cycle
Once the dishwasher is loaded, follow these instructions to start the wash cycle:
1. Ensure the dishwasher is properly connected to power supply.
2. Ensure the water supply is properly connected and is turned on to full pressure.
4. Add detergent and check Rinse Aid is full.
5. Close the door and press the POWER button to turn on the dishwasher.
6. Press the PROGRAM button to select desired program: Heavy -> Normal -> Light ->
Mini Party -> Rinse -> Speed -> Soak.
7. If you wish delay the start time, press the DELAY button to select: 2 hrs -> 4 hrs ->
6 hrs -> 8 hrs.
8. Press the START/PAUSE button to begin the wash cycle.
NOTE: When the START/PAUSE button is pressed during a wash cycle, unit’s operation
is suspended and display on the screen will stop blinking. During the pause, the unit will beep
once every minute until the START/PAUSE button is pressed again to resumes operation.
11
Changing the Wash Program
You can change the wash program if the unit just started and only ran for a short time.
Otherwise, detergent may have been released and water drained. If this is the case,
the detergent dispenser must be refilled.
Press and hold the START/PAUSE button for three seconds or more and unit will be in
stand-by state. The program can be changed at this point.
NOTE: If you open the door during a wash cycle, the unit will be paused. After door is
closed, you need to press the START/PAUSE button to resume operation.
WARNING: opening the door during wash cycle may result in injury from hot water.
Note the following indications of the dishwasher:
· All lights off = Stand by mode
· Display is on steady (not blinking) = Unit is paused
· Display is blinking = Operating
For got to Add a Dish?
Dish can be added any time before detergent is released:
1. Press the START/PAUSE button
2. Open the door slightly to stop the cycle
3. After the spray arm has stopped spinning, open the door fully
4. Add the forgotten dishes
5. Close the door
6. Press the START/PAUSE button and unit will resume operation after 10 seconds
At the End of the Wash Cycle
When wash cycle has finished, the dishwasher will buzz for 8 seconds.
1. Turn off the unit by pressing the POWER button
2. Shut off water supply and open the door.
3. Leave the door ajar and wait a few minutes before unloading. This will allow the dishes
to cool and assist in the drying process. Dishes that are still hot are more susceptible to
breakage.
4. Unload the dishwasher. It is normal for the dishwasher to be wet inside.
12
MAINTENANCE
Filter System
The filter system consists of a Coarse Filter, a Fine Filter and a Main Filter. The filter
system prevents large remnants of food or other objects from getting inside the pump.
C. Coarse Filter
Larger items, such as pieces of bone or glass, that could
block the drain are trapped in the coarse lter. To remove
items caught by this lter, gently squeeze the tap on the
top of the lter and lift out.
B. Fine Filter
This lter holds soil and food residue in the cylindrical base
and prevents it from being redeposited on the dishes.
A. Main Filter
Food and soil particles trapped by this lter are pulverized by
a special jet on the spray arm and washed down the drain.
Filter Assembly
The filter efficiently removes food particles so the wash water can be recycled during a
wash cycle. For best performance and results, the filter assembly must be cleaned
regularly. It is recommended to remove the larger food particles trapped in the filter after
each use by rinsing the filter assembly under running water.
To remove filter assembly:
1. Turn the Filter assembly counter-clockwise and lift to remove
entire assembly.
2. Lift B and C upwards to remove from A.
3. Lift C upward to remove from B.
Reassemble in reverse order - make sure the Fine Filter
is properly seated.
WARNING!
· Inspect the lters after each use.
· Never run the dishwasher without lter assembly in place.
· Improper placement of the lter or damaged lter may reduce
the unit’s performance and may cause damage to dishes
and/or utensils.
· The entire lter assembly should be cleaned at least one a week.
Cleaning the Filters
Use a soft cleaning brush or old toothbrush to clean the Coarse and Fine Filters.
When cleaning the lters, don’t knock or bang them to remove residues, this could contort
the lters and reduce performance of the dishwasher.
13
Cleaning the Dishwasher
The control panel can be cleaned by using a slightly dampened cloth. Dry thoroughly
with a soft towel.
The exterior can be wiped with a towel and mild detergent solution. Wipe clean and
follow with a good appliance polish wax.
Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.
Cleaning the Door
Use only a soft, damp cloth with warm water to clean the edge
around the door. To avoid penetration of water into the door lock
and electrical components, do not use spray cleaner of any kind.
Cleaning the Spray Ar m
The spray arm can be easily removed for periodic
cleaning of the nozzles to prevent possible clogging.
Remove the spray arm by grasping the middle
and pull upwards. Wash the spray arm under running
water and carefully reinstall making sure the rotary
movement is in no way impeded.
WARNING: Abrasive agents and some paper towel may scratch or leave spots on the
stainless steel surface.
Protect Against Freezing
Please take frost protection measures during the winter months. Please follow these
procedures after each wash:
1. Turn off the dishwasher.
2. Turn off water supply and disconnect water inlet hose from the back of the unit.
3. Drain water from the inlet hose and inlet port - use a pan to catch the water.
4. Reconnect the water inlet hose to inlet port.
5. Remove the Filter System and use a sponge to absorb the water in the sump.
NOTE: if your dishwasher cannot operate due to ice, please contact professional service.
14
Keeping Your Dishwasher in Shape
After Ever y Wash
Turn off the water supply and leave the door slightly open so moisture and odors are
not trapped inside
No Solvents or Ab r asive Cleaners
Never use abrasive cleaners or solvents to clean the dishwasher. Only use a dampened
soft towel with warm water. To remove spots or stains on the interior surface, you may
use a cloth dampened with water and a little white vinegar.
Clean the Door Seals
Food that gets trapped in the seals may cause odors to form. Periodic cleaning with a
damp sponge will prevent this from occuring.
Clean Filters Regu larly
Clean the filters regularly to prevent clogs and odors.
Moving the Dishwasher
If the dishwasher must be moved, try to keep it in the upright position. Never position
the dishwasher on its side or upside down.
Preparation for Storage
It is recommended you run a wash cycle with the dishwasher empty. Disconnect from
power and turn off the water supply. Remove any water remaining in the sump area
with a sponge. Leave the door slightly open. this will help the door seals to last longer
and prevent odors from forming inside the dishwasher.
15
TROUBLESHOOTING
ISSUE
POSSIBLE CAUSE
WHAT TO DO
Dishwasher does not
start
Fuse is blown or circuit breaker is
tripped
Replace fuse or reset circuit breaker.
Remove any other appliances sharing
the same circuit
Power supply is not turned on
Make sure dishwasher is turned on and
door is closed securely.
Make sure the power is properly
connected
Dishwasher door is not properly
closed
Close the door and make sure the door
latches
Water not pumped
from dishwasher
Kink in drain hose
Check drain hose
Filter clogged
Check and clean lters
Kitchen sink clogged
Ensure kitchen sink is draining well.
Contact a plumber if sink is not draining
Suds in tub
Improper detergent
Use only specied detergent for
dishwasher use. If improper detergent
was used, open the dishwasher and
allow suds to evaporate. Add 1 gallon of
cold water to the tub. close door and
start the SOAK cycle to drain water.
Repeat if necessary.
Spilled rinse-aid
Always clean up rinse-aid spills
immediately.
Stained tub interior
Detergent used contains colorant
Do not use any detergents with
colorants.
White lm on
dishwasher interior
surface
Hard water minerals
Clean the interior with a damp sponge
and dishwasher detergent and wear
rubber gloves. Never use any other
cleaner for risk of foaming or suds.
Rust stains appear on
cutlery
Items are not non-corrosive
Do not place non-dishwasher safe items
in the dishwasher.
Knocking noise inside
the dishwasher
Spray arm is knocking against an
item in the basket
Pause the wash cycle and rearrange
items which are obstructing the spray
arm.
Rattling noise inside
the dishwasher
Items are not securely placed in
dish rack
Pause the wash cycle to rearrange and
secure items.
Knocking noise in
water pipes
This may be caused by on-site
installation or the cross-section of
the piping
Contact a plumber. This is not related to
the dishwasher.
Review the troubleshooting guide below to resolve common issues:
16
Error Indications
ISSUE
POSSIBLE CAUSE
WHAT TO DO
Dishes are not
cleaned
Dishes were not properly loaded
Reload dishes properly.
Selected wash cycle was not
powerful enough
Select a more intensive wash cycle.
Not enough detergent
Use more or change brand of detergent.
Items are blocking the path of the
spray arm
Rearrange items so the spray arm can
fully rotate.
The lters are dirty/clogged or
installed incorrectly
Clean the lter and/or check installation.
Cloudiness on
glassware
Combination of too much detergent
with soft water
Use less detergent and/or select the
shortest wash cycle to clean glassware.
The lters may be dirty or clogged
Clean lters and/or check installation.
Black or gray marks
on dishes
Utensils may have rubbed against
dishes
Use a mild abrasive cleaner to eliminate
marks. Load more carefully.
Detergent left in
dispenser cup
Dishes blocked the detergent cup
Re-load dishes properly.
Dishes are not dry
Improper loading
Re-load dishes properly.
Not enough rinse-aid
Rell the rinse aid.
Dishes were removed too soon
Do not remove dishes from the
dishwasher immediately after wash.
Wrong cycle selected
Short cycles have lower cleaning
performance. Choose a more intensive
cycle.
Dishes/cutlery have low-quality
coating
Water drainage is more difcult with
these items. Dishes/cutlery of this type
are not suitable in this dishwasher.
INDICATION
MEANINGS
POSSIBLE CAUSES
E1
Restricted water inlet
Water supply is not turned on or
restricted; or water pressure too low
E4
Overow
Some element of dishwasher leaks.
WARNING!
If overow occurs, turn off the main water supply before calling for service.
If there is water in the base pan due to an overll or small leak, the water should be removed
before restarting the dishwasher.
17
Technical Information
Number of place settings
6
Maximum diameter of dishware
10.5 inches
Cycles
7
Unit dimension
21.65W x 19.69D x 17.24H
Water pressure
0.04-1.0MPa
Power supply
see rating label
Noise level
55dB
19.69 in.
18
Your Guarantee
If this product is found to be faulty as a result of faulty materials or workmanship within one year from
date of purchase, it will be repaired free of charge.
This guarantee is subject to the following terms:
Sunpentown must be notied of the fault.
Proof of purchase must be presented to Sunpentown's nominated representative.
The warranty will be void if the product if modied, misused or repaired by an unauthorized person.
The warranty after repair will not be extended beyond the original one-year period.
All replacement parts will be new or reconditioned.
Parts, which are replaced, become the property of Sunpentown.
The warranty applies for the use of the product in the USA only.
What is NOT COVERED:
Warranty does not include freight charges.
Damage due to installation error, product abuse and/or misuse.
Incidental or consequential damage caused by possible defects with this product.
Labor cost incurred for the installation and/or removal of a possible defective unit.
Damage to product caused by improper power supply voltage, accident, re, oods or acts of nature.
Failure of product resulting from unauthorized modications to the product.
Improper installation or failure to perform the necessary maintenance.
Normal wear and tear on parts or replacement of parts designed to be replaced.
Damage to personal property from use of product.
Replacement or repair of household fuses, circuit breakers, wiring or plumbing.
This GUARANTEE is in addition to your Statutory Rights
SUNPENTOWN INTERNATIONAL INC.
14625 Clark Ave. City of Industry, CA 91745
Tel: 800-330-0388
service@sunpentown.com
www.sunpentown.com
Loading...