Page 1
Commercial Radiant Cooktop
RR-1234R
INSTRUCTION MANUAL
Thank you for your purchase.
Please read thoroughly before initial use and keep in a safe
place for future reference.
Page 2
IMPORTANT SAFEGUARDS
Read all instructions.
When the Warming indicator is on, this means the ceramic plate is
extremely hot, DO NOT TOUCH.
To protect against electrical shock, do not immerse cord or appliance
in water or any other liquid.
Close supervision is necessary when any appliance is used by or
near children.
Unplug from outlet when not in use and before cleaning.
Do not operate any appliance with a damaged cord or plug; or after
the appliance malfunctions or has been damaged in any way. Return
appliance to the Sunpentown for examination, repair or adjustment.
The use of accessory attachments not recommended by the
manufacturer may cause injuries.
Do not use outdoors.
Do not allow cord to hang over the edge of table or counter; or touch
hot surfaces.
Do not place on a hot gas/electric burner, or in a heated oven.
Do not use appliance for anything other than intended use.
Use of an extension cord is not recommended. If needed, use an
extension cord of 14 gauges on diameter not longer than 10 feet.
Extreme caution must be used when moving an appliance containing
hot oil or liquid.
To disconnect, turn all controls to OFF position, then uplug.
If glass plate is broken or cracked, stop using the unit immediately.
Turn unit off, unplug and contact Sunpentown. Cleaning solution or
spillovers may penetrate the plate and cause an electric shock.
To avoid scalding and foul fumes produced by cleaning solutions on
a hot surface, wait for the unit to cool considerably before cleaning.
This appliance is not a warming appliance. Do not place food directly
on glass plate.
A short power supply cord should be used to reduce the risk of
becoming entangled in or tripping over a longer cord.
Longer extension cords are available and may be used if care is
exercised in their use:
1) The marked electrical rating of the extension cord should be at
least as great as the electrical rating of the appliance and
2) The cord should be arranged so that it will not drape over
countertops where it can be pulled on by children or tripped over
unintentionally.
This appliance has a polarized plug (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit
into a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Do not attempt to modify the plug in any way.
INDEX
• Important safeguards
• Index
• Structure description & function
• Operation
• Timer
• Lock
• Key points before use
• Selecting the proper cookware
• Care and maintenance
• Specifications
• Trouble shooting
• Save these instructions
• Warranty
Page 3
CONTROL PANEL
LED Display
Timer setting
buttons
Timer button ON/OFF button Control knob
OPERATION
1.Plug power cord to power source and place cookware centered on
cooktop. (Once power is connected, the POWER indicator will illuminate
and then in standby mode.).
2.Press the On/Off button:
CAUTION: When the Warning indicator is on, the ceramic plate is
extremely hot – DO NOT TOUCH.
INSTALLATION
• The cooktop can be surface-mounted into the countertop.
• The cooktop can be flush with the countertop.
If the Control dial is at “off” position, power indicator will flash and
nothing displayed on LED panel. Turn the Control Dial clockwise to
desired setting.
If the Control dial is already turned pass “off” position, power
indicator stays steady on and LED displays current setting.
3.Turn the Control Dial to set at desired level (wattage):
100,200,300,400,500,600,700,800,900,1000,1100,1200,1300,1400
Timer Setting
Press Timer button, Timer indicator illuminates.
Press “+” or “-“ buttons to set in 1-minute increments, press
and hold to set in 10-minute increments. (0-60 min).
Press Timer button again and use “+” or “-“ button to adjust in
1-hour increments (0-24 hrs)
After 5 seconds, off-timer is set and LED will alternate displaying
Power Level and remaining time.
Page 4
KEY POINTS
Voltage
When the Warming indicator is on, this means the ceramic plate is
extremely hot, DO NOT TOUCH.
Cooker will automatically shut-off after 2 hours of inactivity (when not
set on timer).
Place cooktop on flat surface, but keep a clearance of 4 inches all
around for proper ventilation. If air inlet or outlet is blocked, the
internal temperature will rise and cause unit to overheat and shutoff
during cooking.
Never power on unit without cookware. May cause ceramic plate to
overheat and crack.
Keep away from water source. Never immerse unit in water or clean
under running water.
Do not place paper or cloth in between the cooktop and cookware.
To prevent damage to your cookware, do not heat an empty pan.
Do not place one cooktop on top of another.
Do not place on or near a hot gas or electric burner or in a heated
oven. If the surrounding temperature is high, unit will shut off.
Do not use cookware consisting of inferior enamel, synthetic
material, china or aluminum. DO NOT USE PLASTIC WRAP.
SELECTING THE PROPER COOKWARE
This radiant cooktop is not selective with cookware. However,
cookware with a flat bottom and matte finish will have the best heat
conductivity.
It is not suggested to use pressure cooker on the cooktop. If you do
use one, please use with caution.
CARE & MAINTENANCE
Unplug unit from power source.
Wipe ceramic plate and exterior surface with a soft damp cloth. If
excessively dirty, soak cloth in a mild detergent and water mixture.
SPECIFICATIONS
Model RR-1234R
120V~ / 60Hz
Never heat an unopened can on the cooktop as it may explode.
Plug cooktop in a dedicated 15-amp outlet. Do not share the outlet
with other appliances.
Do not damage the ceramic plate. Be careful not to drop anything
onto the ceramic plate. If the plate is broken or cracked, stop using
immediately. Turn unit off and unplug.
Deep-fry is prohibited.
This cooktop is not intended for use by persons (including children)
with reduced physical sensory or mental capabilities; or lack of
experience and knowledge, unless supervised by person responsible
for their safety.
Power consumption 1400W (max)
Dimension 12.6 x 13.4 x 3.94 (H) in.
Weight 12.79 lbs
Power range
Cord length 5.9 ft
100 – 1400W
Page 5
TROUBLESHOOTING / ERROR CODES
heating during normal
PROBLEM CHECK POINTS
Unit is plugged in but
power indicator does
not come on
Power indicator is lit
but not heating
Error code: E5
Error code: E6
Error code: E7
Unit suddenly stops
operation
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
consumer ISM equipment, pursuant to Part 18 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio TV technician for help.
Is cooktop firmly plugged into a correct outlet?
Was there a power shortage?
Please contact Sunpentown
Check if temperature sensor overheated, if fan
is running;or if air outlet or inlet is blocked.
Temperature sensor open circuit, please
contact Sunpentown.
Temperature sensor short circuit, please
contact Sunpentown.
Check if unit reached set timer.
Unit has been operating and idle for 2 hours.
Safety feature automatically shuts unit off after
2 hours with no setting changes.
Is the Display indicating any of the above error
code?
Your Guarantee
If this product is found to be faulty as a result of faulty materials or
workmanship within one year from date of purchase, it will be repaired
free of charge.
This guarantee is subject to the following terms:
• Sunpentown must be notified of the fault.
• Proof of purchase must be presented to Sunpentown’s
nominated representative.
• The warranty will be void if the product if modified, misused or
repaired by an unauthorized person.
• The warranty after repair will not be extended beyond the original
one-year period.
• All replacement parts will be new or reconditioned.
• Parts, which are replaced, become the property of Sunpentown.
• The warranty applies for the use of the product in the USA only.
What is NOT COVERED:
• Warranty does not include freight charges.
• Incidental or consequential damage caused by possible defects
with this product.
• Damage to product caused by improper power supply voltage,
accident, fire, floods or acts of nature.
• Failure of product resulting from unauthorized modifications to
the product.
• Improper installation or failure to perform the necessary
maintenance.
This GUARANTEE is in addition to your Statutory Rights
SUNPENTOWN INTERNATIONAL INC.
1-800-330-0388
service@sunpentown.com
www.spt-usa.com
Loading...