Sunpak 620-423-CFT-PX2 User manual
1/4”-20 Threaded Screw
Your PRO 423PX comes with
a 1/4”-20 threaded screw at
the top of the Center Column.
It also comes with a 3/8”
screw adapter located in the
base of the Pistol Grip Ball
Head. To use it as a 3/8”
center column, remove the
Pistol Grip head, unscrew the
adapter and screw it on the
top of the Center Column.
Short Center Column
Your Sunpak PRO
423PX tripod also
comes with a Short Center Column for low angle
use. To remove the
standard Center Column, first loosen the
Center Column Lock
Knob and simply unscrew the accessory
hook plate from the bottom of the Center Column, and remove it from
the tripod body. Then
install the Short Center
Column for use.
SUNPAK LIMITED LIFETIME WARRANTY
This SUNPAK product has been carefully manufactured, accurately adjusted, inspected and thoroughly tested before shipment
to assure you of the highest quality.
Should this SUNPAK product require service, we will repair or
replace, at our option, any part or the product itself, which our
examination shows to be defective in material or workmanship.
This warranty does not apply to wear and tear associated with
the normal use of the product. This warranty is non-transferable.
Repairs will be made to the product at no charge, under the
terms of the warranty as stated above, only when accompanied
by a dated and itemized bill of sale and nominal handling charge.
Be certain to follow all assembly and/or operating instructions
with this product. This warranty is not valid if the product has
been misused or damaged in any way that is beyond our control
or through normal wear and tear associated with use. This warranty applies only to the product and we are not responsible in
any way for losses, damages or any inconvenience caused by
equipment failure.
Some states do not allow the exclusion or limitation of consequential damages, so the above limitation or exclusion may not
apply to you. This warranty gives you specific legal rights and
you may have other rights which may vary from state to state.
Should service be required, the product should be carefully
packed (in the original packaging if possible ) and sent, prepaid
and insured, along with a check or money order for $15.95
(shipping and handling), to the address listed below. A note
briefly describing the nature of the defect should also be enclosed to expedite handling.
Proof of purchase and payment for shipping and handling
PRO 423PX
Operating Instructions
Congratulations on the purchase of your new
SUNPAK tripod. Your tripod has been designed
to be a sturdy, rugged, and dependable product and
will provide you with many years of reliable service.
Please spend a few moments reviewing these
instructions, so that you can take full advantage
of your tripod’s features and capabilities.
Precautions
Insure that all handles, knobs and leg locks
are properly tightened, and that all three
legs are fully angled opened before use.
Do not carry or transport the tripod with the
camera equipment attached (as example
but not limited to: over your shoulder or
cradled in your arms).
Do not Oil or Grease any part of the tripod.
Do not use any solvents or thinners to clean
your tripod. Use mild detergent and wipe dry
with a soft, lint-free cloth only.
Do not store or expose your tripod to
excessive heat or cold or use close to any
flame or fire.
Do not exceed the load limit for this product.
All Specifications Subject to Change without Notice.
OWNER’S RECORD
Please complete this section and retain with your original bill of
sale for your records.
Purchase Date ________________________________________
Model _______________________________________________
Dealer’s Name ________________________________________
Address _____________________________________________
City ________________________________________________
State ___________________ Zip Code ____________________
ToCAD America Inc.
Sunpak Tripod Division
53 Green Pond Road
Rockaway, NJ 07866
973-627-9600
tocad.com
Cat. no. 620-423-CFT-PX2
PRO 423PX2 Specifications
Leg Sections 3
Leg Construction Carbon Fiber
Maximum Height 66.75 in.
Minimum Height 10.5 in.
Folded Length 26.5 in.
Leg Diameter .75 in.
Weight 3 lbs.
Load Capacity 15.4 lbs.
Tripod Components (See Picture Below)
1. Pistol Grip Ball Head with Quick Release
2. Trigger Control Lock
3. Quick Release Plate
4. Quick Release Lock Lever with Locking
Mechanism
5. Center Column Lock Knob
6. Leg Angle Adjustment Latch
7. Center Column
8. Retractable Accessory Hook
9. Flip Lock Leg Locks
10. Rubber Feet with Retractable Leg Spikes
11. Short Center Column
3
4
1
2
6
5
11
6
7
8
Extending the Legs
Each leg of the PRO 423PX
has separate leg extensions
and each segment may be
withdrawn as needed by
using the flip lock leg locks.
This permits setting your
equipment at a comfortable
height can be very useful
when positioning your tripod
on uneven terrain. To
secure, close the leg lock
firmly in place. Not properly
securing a leg lock may
cause the tripod leg to
retract and may cause
damage to your tripod and
camera.
Adjusting Leg Angle
To change the operation
angle of any leg, fold the leg
in slightly towards the center
column, push downward on
the Leg Angle Adjustment
Latch until it locks. You can
then spread the leg outward
to it lowest angle, or fold the
legs inward, which will lock
the legs at greater angles, if
desired.
Using the Pistol Grip Ball Head
For movement in any direction, simply loosen the
Pistol Grip Ball Head, by squeezing the Trigger
Control Lock. When you have reached your desired
position, simply release the trigger lock and the Pistol Grip Ball Head will lock into place. The Pistol
Grip Ball Head can rotate to 360° in any direction.
Quick Release Plate
Push forward the Locking Mechanism located just
below the Quick Release Lock Lever. Move the
Quick Release Lock Lever outward and remove
the Quick Release Plate by lifting upward. The
platform has a threaded ¼ x 20 camera mounting
screw for camera attachment.
Position the Quick Release Plate so that the camera mounting screw aligns with the matching
receptacle on your camera or camcorder and
attach, using the camera mounting screw. Move
and hold open the Quick Release Lock Lever and
with the camera tilted slightly down, slide the
Quick Release Plate back into position. After doing
so, secure the Quick Release Plate using the
Quick Release Lock Lever by pressing firmly until
it stops. Note: Do not attempt to open the
Quick Release Lock Lever without pressing
the Locking Mechanism first.
Locking
Mechanism
Height Adjustments
Your Sunpak PRO 423PX tripod is equipped with a
Lift-n-Lock Center Column for precise height adjustments.
To raise or lower the Center Column, loosen the
Center Column Lock Knob. Grasp the tripod head
and lift to the desired height. Retighten the Center
Column Lock Knob to secure.
Note: Never release your camera until the Center
Column Lock Knob is securely retightened.
10
9
Loading...