Sun Oracle SPARC T4-1B Installation Manual

SPARC T4-1B Server Module
Installation Guide
Part No.: E22738-03 May 2012
Copyright ©2011, 2012 Oracle and/or its affiliates. Allrights reserved. This softwareand related documentation areprovided under a license agreementcontaining restrictionson useand disclosure and are protected by
The informationcontained hereinis subjectto changewithout noticeand isnot warrantedto beerror-free.If youfind anyerrors, pleasereport them to us in writing.
If thisis softwareor related software documentationthat isdelivered to the U.S. Government or anyone licensing it on behalf of the U.S. Government, the following noticeis applicable:
U.S. GOVERNMENTEND USERS.Oracle programs,including anyoperating system,integrated software, any programsinstalled on the hardware, and/or documentation,delivered toU.S. Governmentend usersare "commercial computer software" pursuantto theapplicable FederalAcquisition Regulation andagency-specific supplementalregulations. Assuch, use,duplication, disclosure, modification, andadaptation ofthe programs,including any operatingsystem, integratedsoftware, anyprograms installed on the hardware,and/or documentation,shall besubject tolicense termsand license restrictions applicableto theprograms. No other rights are granted to the U.S. Government.
This softwareor hardware is developed forgeneral usein avariety ofinformation management applications. It is not developedor intendedfor usein any inherently dangerous applications, includingapplications whichmay createa riskof personal injury. If you use this softwareor hardware in dangerous applications, thenyou shallbe responsibleto takeall appropriate fail-safe, backup,redundancy, and other measuresto ensureits safeuse. Oracle Corporation andits affiliatesdisclaim anyliability forany damagescaused byuse ofthis software or hardware in dangerous applications.
Oracle andJava areregistered trademarks of Oracle and/or its affiliates.Other namesmay betrademarks oftheir respectiveowners.
Intel andIntel Xeonare trademarksor registered trademarks ofIntel Corporation.All SPARC trademarks are used under license and are trademarksor registered trademarks of SPARCInternational, Inc.AMD, Opteron, theAMD logo,and theAMD Opteron logo are trademarks orregistered trademarks of Advanced MicroDevices. UNIXis aregistered trademark of The Open Group.
This software or hardware and documentation may provide access to or information on content, products, and services from third parties. Oracle Corporation and its affiliates are not responsible for and expressly disclaim all warranties of any kind with respect to third-party content, products, and services. Oracle Corporation and its affiliates will not be responsible for any loss, costs, or damages incurred due to your access to or use of third-party content, products, or services.
Copyright ©2011,2012, Oracle et/ou ses affiliés.Tous droits réservés. Ce logicielet ladocumentation quil’accompagne sontprotégés parles loissur lapropriété intellectuelle. Ils sont concédés sous licence et soumis à des
restrictions d’utilisationet dedivulgation. Saufdisposition devotre contrat de licence ou de la loi, vous ne pouvez pas copier, reproduire,traduire, diffuser,modifier, breveter, transmettre,distribuer,exposer,exécuter, publier ouafficher lelogiciel, mêmepartiellement, sous quelque formeet par quelque procédéque cesoit. Parailleurs, ilest interdit de procéderà toute ingénierie inversedu logiciel, de ledésassembler ou de ledécompiler, excepté à des finsd’interopérabilité avecdes logicielstiers outel queprescrit par la loi.
Les informationsfournies dansce documentsont susceptiblesde modificationsans préavis.Par ailleurs,Oracle Corporationne garantitpas qu’elles soient exemptesd’erreurs etvous invite,le caséchéant, àlui enfaire part par écrit.
Si celogiciel, oula documentationqui l’accompagne,est concédésous licenceau Gouvernementdes Etats-Unis,ou àtoute entitéqui délivrela licencede ce logicielou l’utilisepour lecompte duGouvernement desEtats-Unis, lanotice suivantes’applique :
U.S. GOVERNMENTEND USERS.Oracle programs,including anyoperating system,integrated software, any programsinstalled on the hardware, and/or documentation,delivered toU.S. Governmentend usersare "commercial computer software" pursuantto theapplicable FederalAcquisition Regulation andagency-specific supplementalregulations. Assuch, use,duplication, disclosure, modification, andadaptation ofthe programs,including any operatingsystem, integratedsoftware, anyprograms installed on the hardware,and/or documentation,shall besubject tolicense termsand license restrictions applicableto theprograms. No other rights are granted to the U.S. Government.
Ce logicielou matériela étédéveloppé pourun usagegénéral dansle cadred’applications degestion desinformations. Celogiciel oumatériel n’estpas conçu nin’est destinéà êtreutilisé dansdes applicationsà risque,notamment dansdes applicationspouvant causerdes dommagescorporels. Si vous utilisez celogiciel oumatériel dansle cadred’applications dangereuses, il estde votreresponsabilité de prendretoutes lesmesures de secours, de sauvegarde, deredondance et autres mesures nécessairesà sonutilisation dansdes conditionsoptimales desécurité. OracleCorporation etses affiliés déclinent touteresponsabilité quantaux dommagescausés parl’utilisation dece logicielou matérielpour cetype d’applications.
Oracle etJava sontdes marquesdéposées d’OracleCorporation et/oude sesaffiliés.Tout autre nom mentionné peut correspondre à desmarques appartenant àd’autres propriétaires qu’Oracle.
Intel etIntel Xeonsont desmarques oudes marques déposées d’IntelCorporation. Toutes lesmarques SPARCsont utiliséessous licenceet sontdes marques oudes marques déposées deSPARC International, Inc.AMD, Opteron, le logoAMD etle logoAMD Opteronsont desmarques ou des marques déposées d’AdvancedMicro Devices.UNIX estune marque déposée d’TheOpen Group.
Ce logicielou matérielet ladocumentation quil’accompagne peuventfournir desinformations oudes liensdonnant accèsà descontenus, desproduits et des servicesémanant detiers. OracleCorporation etses affiliésdéclinent touteresponsabilité ou garantie expresse quant aux contenus, produits ou services émanantde tiers.En aucuncas, OracleCorporation etses affiliésne sauraientêtre tenus pour responsables des pertes subies, des coûts occasionnés oudes dommagescausés parl’accès àdes contenus,produits ouservices tiers,ou àleur utilisation.
Please
Recycle

Contents

Using This Documentation v
Understanding the Server Module 1
Installation Task Overview 1
Server Module Overview 2
Front and Rear Panel Components 4
Confirming Server Module and Site Specifications 7
Physical Specifications 7
Environmental Specifications 8
Electrical Specifications 8
Preparing for Installation 11
Inventory 12
Handling Precautions 13
ESD Precautions 13
Tools Needed for Installation 14
Plan Communication With the Server Module During Installation 15
Dongle Cables 17
Installing the Server Module 21
Prepare the Modular System and Server Module 21
Install Optional Components 23
Insert the Server Module Into the Chassis 23
iii
Powering On the Server Module for the First Time 27
Method 1a – Power On the Host Through the CMM (Web Interface) 28
Method 1b – Power On the Host Through the CMM (CLI) 29
Method 2 – Power On the Host Through the CMM SER MGT Port (CLI)
31
Method 3 – Power On the Host Through the Front Panel (SP CLI) 34
Configuring the Oracle Solaris OS 37
Configure the OS 37
Install Oracle Solaris Software From the Network 38
Oracle Solaris Configuration Parameters 38
Assign a Static IP Address to the SP 40
Glossary 43
Index 49
iv SPARC T4-1B Server Module Installation Guide • May 2012

Using This Documentation

This document provides instructions and reference material to help you install Oracle’s SPARC T4-1B server module in Oracle’s Sun Blade 6000 modular system.
“Related Documentation” on page v
“Feedback” on page vi
“Support and Accessibility” on page vi
Related Documentation
Documentation Links
All Oracle products http://www.oracle.com/documentation
SPARC T4-1B server module
Sun Blade 6000 modular system
Oracle Integrated Lights Out Manager (Oracle ILOM)
Oracle Solaris OS and other system software
Oracle VTS software http://www.oracle.com/pls/topic/lookup?ctx=OracleVTS7.0
SAS-1/SAS-2 Compatibility
http://www.oracle.com/pls/topic/lookup?ctx=SPARCT4-1B
http://www.oracle.com/pls/topic/lookup?ctx=E19938-01
http://www.oracle.com/pls/topic/lookup?ctx=ilom30
http://www.oracle.com/technetwork/indexes/documentation/#sys_sw
http://www.oracle.com/pls/topic/lookup?ctx=E22513_01
v
Feedback
Provide feedback on this documentation at:
http://www.oracle.com/goto/docfeedback
Support and Accessibility
Description Links
Access electronic support through My Oracle Support
http://support.oracle.com
For hearing impaired:
http://www.oracle.com/accessibility/support.html
Learn about Oracle’s commitment to accessibility
vi SPARC T4-1B Server Module Installation Guide • May 2012
http://www.oracle.com/us/corporate/accessibility/index.html

Understanding the Server Module

The following topics describe the server module and installation tasks.
“Installation Task Overview” on page 1
“Server Module Overview” on page 2
“Front and Rear Panel Components” on page 4
Related Information
“Confirming Server Module and Site Specifications” on page 7

Installation Task Overview

Perform the following tasks to install the server module.
Step Description Links
1. Review the product notes for any late-breaking news.
2. Review the server module features and components.
3. Review the server module requirements. “Confirming Server Module and Site
4. Confirm that you received all the items you ordered.
5. Review safety and ESD precautions. “Handling Precautions” on page 13
6. Gather the required tools. “Tools Needed for Installation” on
SPARC T4-1B Server Module Product Notes
“Server Module Overview” on page 2
“Front and Rear Panel Components” on page 4
Specifications” on page 7
“Inventory” on page 12
“ESD Precautions” on page 13
page 14
1
Step Description Links
7. Choose a method by which to connect to the server module during installation.
8. Install optional components in the server module and install the server module in the chassis.
9. Power on the server module for the first time.
10. Configure the OS on the host. “Configuring the Oracle Solaris OS” on
“Plan Communication With the Server Module During Installation” on page 15
“Dongle Cables” on page 17
“Installing the Server Module” on page 21
“Powering On the Server Module for the First Time” on page 27
page 37
Related Information
“Server Module Overview” on page 2
“Front and Rear Panel Components” on page 4

Server Module Overview

2 SPARC T4-1B Server Module Installation Guide • May 2012
Feature Description
Processor One SPARC T4 multicore processor.
Memory 16 slots for DDR3 DIMMs.
Internal hard drives Up to two hot-pluggable 2.5-inch SAS-2 hard drives.
REM RAID expansion module (hard drive management) with RAID controller. Refer to the
SPARC T4-1B Server Module Product Notes for details about supported REMs.
UCP One UCP in the front panel. Use a UCP-3 or UCP-4 dongle cable to access the
following server module connectors:
• USB 2.0 (two connections)
• Serial
• VGA video
• Local KVMS support
Architecture SPARC V9 architecture, ECC protected.
Platform group: sun4v.
Platform name: ORCL,SPARC-T4-1B.
Ethernet ports Two 10/100/1000 Mb Intel 82576EB ports.
PCI I/O Two Gen2-capable PCI EM slots.
FEM Refer to the SPARC T4-1B Server Module Product Notes for details about supported
FEMs.
System firmware Preinstalled on the SP.
Note - Refer to the Server Module Product Notes for details on the latest firmware.
Operating system Oracle Solaris OS
Note - Refer to the Server Module Product Notes for details on software that is preinstalled and for information about required patches for supported Oracle Solaris OS releases.
Remote management SP running the Oracle ILOM.
Power The modular system chassis provides power.
Cooling The modular system chassis provides environmental controls.
Related Information
“Front and Rear Panel Components” on page 4
“Installation Task Overview” on page 1
“Confirming Server Module and Site Specifications” on page 7
Understanding the Server Module 3

Front and Rear Panel Components

No. Description
1 RFID tag (provides the serial number of the server module)
2 Universal connector port (UCP)
3 Drive slots
4 White LED: Locator (functions as the physical presence switch)
5 Blue LED: Ready to Remove
6 Amber LED: Fault (Service Action Required)
7 Green LED: OK
8 Power button
9 Reset button: NMI (for service use only)
10 Green LED: Drive OK
11 Amber LED: Drive Fault (Service Action Required)
12 Blue LED: Drive Ready to Remove
4 SPARC T4-1B Server Module Installation Guide • May 2012
No. Description
13 Rear chassis power connector
14 Rear chassis data connection
Related Information
“Server Module Overview” on page 2
“Installation Task Overview” on page 1
Understanding the Server Module 5
6 SPARC T4-1B Server Module Installation Guide • May 2012

Confirming Server Module and Site Specifications

Site-planning information is included in the documentation for the Sun Blade 6000 modular system. Refer to the Site Planning Guide for Sun Blade 6000 and Sun Blade 6048 Modular Systems.
These topics help you plan installation of the server module.
“Physical Specifications” on page 7
“Environmental Specifications” on page 8
“Electrical Specifications” on page 8
Related Information
“Installing the Server Module” on page 21
“Installation Task Overview” on page 1
“Server Module Overview” on page 2

Physical Specifications

Measure U.S. Metric
Width 1.8 in. 44.5 mm
Depth 20.1 in. 511.7 mm
Height 12.9 in. 327.2 mm
*
Weight
* Weight specifications vary based on the model and internal options.
16.4 lbs 7.4 kg
7
Related Information
“Environmental Specifications” on page 8
“Electrical Specifications” on page 8

Environmental Specifications

Condition Requirement
Operating temperature 5˚C (41˚F) to 35˚C (95˚F) noncondensing
Nonoperating temperature -40˚C (-40˚F) to 65˚C (149˚F)
Operating humidity 10% to 90% noncondensing, 27˚C (80˚F) max. wet bulb
Nonoperating humidity 93% noncondensing, 38˚C (100˚F) max. wet bulb
Operating altitude 3048 meters (10,000 feet) at 35˚C (95˚F)
Nonoperating altitude 12,000 meters (40,000 feet)
Related Information
“Physical Specifications” on page 7
“Electrical Specifications” on page 8

Electrical Specifications

Measure Value
Voltage (nominal) 12V main from chassis backplane
3.3V AUX from chassis backplane
Power (maximum) 540W (estimated)
Related Information
“Physical Specifications” on page 7
8 SPARC T4-1B Server Module Installation Guide • May 2012
“Environmental Specifications” on page 8
Confirming Server Module and Site Specifications 9
10 SPARC T4-1B Server Module Installation Guide • May 2012

Preparing for Installation

These topics help you prepare to install the server module.
“Inventory” on page 12
“Handling Precautions” on page 13
“ESD Precautions” on page 13
“Tools Needed for Installation” on page 14
“Plan Communication With the Server Module During Installation” on page 15
“Dongle Cables” on page 17
Related Information
“Installing the Server Module” on page 21
“Installation Task Overview” on page 1
11

Inventory

No. Description
1 Printed documentation, including Getting Started Guide.
2 Server module.
3 Customer information sheet (on outside of shipping carton). Save this sheet as a
record of the MAC address and other information about installed hardware and software.
Related Information
“Handling Precautions” on page 13
“ESD Precautions” on page 13
12 SPARC T4-1B Server Module Installation Guide • May 2012
“Tools Needed for Installation” on page 14
“Plan Communication With the Server Module During Installation” on page 15
“Dongle Cables” on page 17

Handling Precautions

Use both hands to carry the server module.
Extend the ejector arms on the front panel only while they need to be in that
position to perform a step in a task.
Related Information
“Physical Specifications” on page 7
“Inventory” on page 12
“ESD Precautions” on page 13
“Tools Needed for Installation” on page 14
“Plan Communication With the Server Module During Installation” on page 15
“Dongle Cables” on page 17

ESD Precautions

Electronic equipment is susceptible to damage by static electricity. Use a grounded antistatic wrist strap, foot strap, or equivalent safety equipment to prevent ESD when you install the server module.
Caution – To protect electronic components from ESD, which can permanently
disable the system, place components on an antistatic surface, such as an antistatic discharge mat, an antistatic bag, or a disposable antistatic mat. Wear an antistatic grounding strap connected to a metal surface on the chassis when you work on system components.
The following figure shows the modular system chassis ground connector for which you can connect antistatic equipment.
Preparing for Installation 13
Related Information
“Inventory” on page 12
“Handling Precautions” on page 13
“Tools Needed for Installation” on page 14
“Plan Communication With the Server Module During Installation” on page 15
“Dongle Cables” on page 17

Tools Needed for Installation

The following tools are sufficient for installing the server module, whether or not you need to install components inside the server module:
Antistatic mat
Antistatic wrist strap
UCP-3 or UCP-4 dongle cable
Terminal or terminal emulator
Stylus (to press power button)
Related Information
“Dongle Cables” on page 17
“Handling Precautions” on page 13
14 SPARC T4-1B Server Module Installation Guide • May 2012
“ESD Precautions” on page 13
“Plan Communication With the Server Module During Installation” on page 15
“Inventory” on page 12
Plan Communication With the Server
Module During Installation
There are several methods to communicate with the server module during the initial installation. Plan which method you will use. Before you perform the installation, arrange to have the equipment, information, and permissions required by that method.
Note – For information about identifying and configuring IP and MAC addresses,
refer to the configuring network addresses information in the Server Module Administration Guide.
Choose one of the connection methods to communicate with the server module
SP.
The connection methods are shown in the figure and described in the table. Obtain the cables, monitoring devices, addresses, and passwords required for the method you choose.
Preparing for Installation 15
Method Connection Description Connection Requirements
1 Ethernet
From: CMM NET MGT port
To : Your network
The CMM NET MGT port must be connected to your network.
You must know the IP addresses of the CMM.
From your network, you must be able to log in to Oracle ILOM on the CMM using the IP address of the CMM. Then you can use the Oracle ILOM proxy to navigate to the server module SP Oracle ILOM interface.
See “Method 1a – Power On the Host Through the
CMM (Web Interface)” on page 28 and “Method 1b – Power On the Host Through the CMM (CLI)” on page 29.
2 Serial
From: CMM SER MGT port
To : Terminal device
A terminal device connected to the CMM SER MGT RJ-45 port. From this connection, you can use Oracle ILOM to navigate to the server module SP Oracle ILOM CLI interface. See “Method 2 – Power On the
Host Through the CMM SER MGT Port (CLI)” on page 31.
3 Serial
From: Server module SP UCP port (dongle required)
To : Terminal device
A UCP-3 dongle cable that connects directly to the server module and a terminal device connected to the RJ-45 connector on the dongle cable. See “Method 3 –
Power On the Host Through the Front Panel (SP CLI)” on page 34.
Supported Interfaces
a) CMM Oracle ILOM web interface
b) CLI
CMM Oracle ILOM CLI
SP Oracle ILOM CLI
16 SPARC T4-1B Server Module Installation Guide • May 2012

Related Information

“Dongle Cables” on page 17
“Inventory” on page 12
“Handling Precautions” on page 13
“ESD Precautions” on page 13
“Tools Needed for Installation” on page 14

Dongle Cables

For setup, testing, or service purposes, you can connect cables directly to the server module SP by first attaching a dongle cable to the UCP on the front panel of the server module.
Caution – Dongle cables should be removed when not in use. These cables have not
been evaluated for electromagnetic compatibility compliance and are not to be used during normal system operation.
There are two types of dongle cables you can use:
UCP-3 – Three-connector dongle cable (preferred) ships with the server module.
Use the RJ-45 connector to connect to the server module SP.
UCP-4 – Four-connector dongle cable (previous version). You must use the DB-9
connector to connect to the server module SP. The RJ-45 connector is not supported. If you need an RJ-45 connection, attach an optional DB-9-to-RJ-45 adapter to the DB-9 connector.
Preparing for Installation 17
FIGURE: UCP-3 Three-Connector Dongle Cable
Figure Legend
1 Dongle connector attaching to the server module UCP
2 RJ-45 serial connector
3 USB 2.0 (two connectors)
4 VGA 15-pin female connector
5 Insertion and release buttons
18 SPARC T4-1B Server Module Installation Guide • May 2012
FIGURE: UCP-4 Four-Connector Dongle Cable
Figure Legend
1 Dongle connector attaching to the server module UCP
2 RJ-45 serial connector (Do not use this connector on the UCP-4)
3 DB-9 serial male connector (TTYA)
4 USB 2.0 (two connectors)
5 VGA 15-pin female connector
6 Insertion and release buttons
Related Information
“Inventory” on page 12
“Handling Precautions” on page 13
“ESD Precautions” on page 13
“Tools Needed for Installation” on page 14
“Plan Communication With the Server Module During Installation” on page 15
Preparing for Installation 19
20 SPARC T4-1B Server Module Installation Guide • May 2012

Installing the Server Module

The following topics describe how to physically install the server module into the modular system.
Step Description Links
1. Prepare the modular system chassis and server module for installation.
2. Install any optional components. “Install Optional Components” on
3. Insert the server module into the chassis. “Insert the Server Module Into the
Related Information
“Powering On the Server Module for the First Time” on page 27
“Installation Task Overview” on page 1
“Prepare the Modular System and Server Module” on page 21
page 23
Chassis” on page 23
Prepare the Modular System and
Server Module
You must install and configure the Sun Blade 6000 modular system (chassis) before installing the server module.
1. Ensure that the modular system is installed and functional.
Satisfying the following conditions ensures a straightforward installation of the server module:
a. Install the modular system into its intended rack before installing server
modules.
21
b. If you plan to manage the server modules through the modular system CMM,
configure the CMM to run in your network.
c. Ensure that the modular system chassis is powered on and running.
d. Ensure that the modular system is running the latest version of Oracle’s
CMM ILOM firmware.
Note – For more information about preparing the modular system and the CMM
ILOM, refer to the Sun Blade 6000 Modular System Installation Guide.
2. (If necessary) Upgrade all SAS-1 components.
This server module is a SAS-2 component. You must upgrade the firmware of all SAS-1 components (such as SAS-1 NEMs and disk modules) to a firmware version that supports SAS-1/SAS-2 coexistence. You must complete this firmware upgrade before you insert this server module or any other SAS-2 component into the modular system chassis. Refer to the SAS-1/SAS-2 Compatibility Upgrade Guide for more information. See “Related Documentation” on page v.
3. Unpackage the server module.
Be ready to insert the server module within 60 seconds of removing the filler panel.
4. Install any optional components.
See “Install Optional Components” on page 23.
5. Be prepared to communicate with the server module as quickly as possible after completing the physical installation.
As soon as you insert the server module in a powered modular system, power is supplied to the server module and the SP generates messages. If you want to see these messages, be ready to connect using one of the methods in “Plan
Communication With the Server Module During Installation” on page 15.

Related Information

“Install Optional Components” on page 23
“Insert the Server Module Into the Chassis” on page 23
22 SPARC T4-1B Server Module Installation Guide • May 2012

Install Optional Components

Optional components that you order as part of the server module’s initial configuration are installed in the server module before it is shipped. These optional components are identified on the customer information sheet included with the server module’s packaging.
However, if you ordered optional components separately, you must install them in the server module before you install the server module in the modular system chassis.
1. Install any optional components in the server module.
To install any optional components, refer to the SPARC T4-1B Server Module Service Manual and to the documentation for the optional component.
2. Close the server module.
3. Insert the server module into the chassis.
See “Insert the Server Module Into the Chassis” on page 23.

Related Information

“Prepare the Modular System and Server Module” on page 21
“Install Optional Components” on page 23
Insert the Server Module Into the
Chassis
1. (If necessary) Prepare the modular system and server module.
See “Prepare the Modular System and Server Module” on page 21.
2. (If necessary) Install any optional components.
See “Install Optional Components” on page 23.
3. Remove the protective cover from the rear connector of the server module.
Installing the Server Module 23
4. Locate the slot in the chassis where you plan to install the server module.
A filler panel should remain in this slot until just before you are ready to insert the server module. All slots should remain filled with server modules or filler panels to ensure correct air flow, heat, and electromagnetic interference conditions in the modular system.
5. Remove the filler panel from the selected chassis slot.
Pull down the ejector arm of the filler panel, then pull the panel straight out of the chassis.
Caution – Be ready to insert the server module within 60 seconds of removing the
filler panel.
6. Use both hands to position the server module vertically with the ejector arms on the right (panel 1).
7. Push the server module into the empty slot until the module extends about 1.5 cm (0.5 inch) from the chassis front (panel 2).
8. Pinch the ejector levers to open them (panel 2).
9. Push the server module into the chassis and close the ejector levers (panel 2 and
3).
24 SPARC T4-1B Server Module Installation Guide • May 2012
10. Monitor status messages when power is applied to the server module (panel 4).
As soon as you insert the server module into a chassis that is connected to power, the server module goes into standby mode and its SP initializes. The front panel LEDs blink three times, then the green OK LED on the front panel blinks for a few minutes. See “Front and Rear Panel Components” on page 4.

Related Information

“Prepare the Modular System and Server Module” on page 21
“Install Optional Components” on page 23
“Front and Rear Panel Components” on page 4
Installing the Server Module 25
26 SPARC T4-1B Server Module Installation Guide • May 2012

Powering On the Server Module for the First Time

After you install the server module in the modular system, you power on the server module host for the first time.
Based on the connection method you selected from “Plan Communication With the
Server Module During Installation” on page 15, perform one of the tasks in this table
to power on the server module:
Description Links
Through a browser that is on the same network as the CMM, use the CMM ILOM web interface.
Through a terminal window on a system that is on the same network as the CMM, use the CMM ILOM CLI.
Through a terminal device connected to the CMM SER MGT port, use the CMM ILOM CLI.
Through a terminal device connected to the front panel of the server module (using the dongle cable), use the server module SP ILOM CLI.
“Method 1a – Power On the Host Through the CMM (Web Interface)” on page 28
“Method 1b – Power On the Host Through the CMM (CLI)” on page 29
“Method 2 – Power On the Host Through the CMM SER MGT Port (CLI)” on page 31
“Method 3 – Power On the Host Through the Front Panel (SP CLI)” on page 34
Related Information
“Configuring the Oracle Solaris OS” on page 37
“Installation Task Overview” on page 1
Server Module Administration Guide
27
Method 1a – Power On the Host
Through the CMM (Web Interface)
You connect to the CMM through the RJ-45 NET MGT 0 Ethernet port. While this Ethernet connection supports both the CLI and the web interface to the CMM, this procedure uses the web interface. By default, the server module is configured to use DHCP to obtain the IP address for the SP.
1. Ascertain the IP addresses for the CMM.
2. Ensure that the CMM is connected to the network you are on.
The network connection is through the RJ-45 connector labeled NET MGT 0 on the CMM.
3. In a browser on the same network as the modular system, enter the IP address of the CMM.
For example, if your CMM has the IP address 129.99.99.99, enter http://129.99.99.99 into your browser.
A login window for ILOM appears.
4. Log into ILOM on the CMM by typing your user name and password.
The factory default ILOM root password is changeme, but might have been changed in your environment.
You are logged in to the CMM ILOM web interface.
5. If the Chassis View (image of the modular system) is not displayed in the web interface, select the Chassis entry in the left navigation panel.
6. Use one of the following methods to navigate to the server module SP.
Select the newly installed server module in the Chassis View (image) of the
modular system.
In the left Chassis navigation panel, select the newly installed server module
(listed as Blade 0 - 9).
7. If prompted to log in, enter the following factory default user name and password:
User name: root
Password: changeme
You are now connected to the server module SP.
8. Open a Remote Console.
28 SPARC T4-1B Server Module Installation Guide • May 2012
a. Select the Remote Control tab on the top menu.
b. Click on Use serial redirection.
c. Click on Launch Remote Console.
This remote console will display host messages and prompts for installing the Oracle Solaris OS when you power on the server module.
9. Power on the server module.
a. Select the Remote Power Control tab.
b. Click on the menu and select Power On.
c. Select Save.
d. Select OK when you see this prompt: Are you sure you want to
perform a Power On of the server.
The server module host is powered on for the first time.
10. You can now configure the Oracle Solaris OS to meet your needs.
See “Configuring the Oracle Solaris OS” on page 37.

Related Information

“Plan Communication With the Server Module During Installation” on page 15
Method 1b – Power On the Host
Through the CMM (CLI)
You connect to the CMM through the RJ-45 NET MGT 0 Ethernet port. While this Ethernet connection supports both the CLI and the web interface to the CMM SP, this procedure uses the CMM CLI.
1. Ascertain the IP addresses for the CMM.
2. Ensure that the CMM is connected to the network you are on.
The network connection is through the RJ-45 connector labeled NET MGT 0 on the CMM.
Powering On the Server Module for the First Time 29
3. Log in to the CMM with the SSH client.
$ ssh root@cmm_ip_address
Replace cmm_ip_address with the IP address of the CMM.
4. Type your password for the CMM ILOM root account when prompted.
The factory default ILOM root password is changeme, but might have been changed in your environment.
Password: CMM_ILOM_password Oracle(TM) Integrated Lights Out Manager Version 3.x.x ... Warning: password is set to factory default.
->
You are now logged in to the CMM ILOM CLI.
Note – When you are ready to log out of the CMM ILOM, type exit.
5. Navigate to the server module SP.
-> cd /CH/BLn/SP/cli
Replace n with a number that identifies the chassis slot in the modular system where the target server module is installed.
6. Access the server module SP.
-> start Are you sure you want to start /CH/BLn/SP/cli (y/n)? y start: Connecting to /CH/BLn/SP/cli as user root
If you are prompted for a password for the root user on the server module SP, type changeme (the factory default password).
You are now logged into ILOM on the server module SP.
30 SPARC T4-1B Server Module Installation Guide • May 2012
7. At the server module ILOM prompt, type:
-> start /SYS Are you sure you want to start /SYS (y/n)? y Starting /SYS. . .
The server module initializes.
8. Switch communication to the server module host.
When the ILOM prompt appears, type:
-> start /HOST/console Are you sure you want to start /HOST/console (y/n)? y Serial console started. To stop, type #. ...
The server module might take several minutes to complete POST. If a boot device installed with Oracle Solaris OS is accessible locally, the server module boots. Otherwise, the server module uses the boot net command to seek a boot device on the network.
You are now connected to the server module host.
9. The server module hardware installation is now complete.
You can now configure the Oracle Solaris OS to meet your needs. See
“Configuring the Oracle Solaris OS” on page 37.

Related Information

“Plan Communication With the Server Module During Installation” on page 15
Method 2 – Power On the Host
Through the CMM SER MGT Port (CLI)
You can access the server module SP by first accessing the chassis CMM ILOM through a terminal or terminal emulator connected to the RJ-45 serial port on the chassis. Then you can connect to the server module SP through the CLI of the CMM ILOM software.
Powering On the Server Module for the First Time 31
1. Verify that the terminal, laptop, or terminal server that will connect to the chassis is operational.
2. Configure the terminal device or terminal emulation software with these settings:
8N1 (eight data bits, no parity, one stop bit)
9600 baud (the default, but can be set to any standard rate up to 57600)
Disable hardware flow control (CTS/RTS)
3. Connect a serial cable from the chassis serial port to the terminal device.
Refer to the modular system chassis documentation for the location of the serial port.
The serial port requires a cable with these pin assignments.
Pin Signal Description
1 Request To Send (RTS)
2 Data Terminal Ready (DTR)
3 Transmit Data (TXD)
4 Ground
5 Ground
6 Receive Data (RXD)
7 Data Carrier Detect (DCD)
8 Clear To Send (CTS)
4. Press Enter on the terminal device.
The connection between the terminal device and the CMM is established.
If you connected to the serial port before the powering on the modular system, you will see boot messages. The CMM ILOM software displays its login prompt:
ORACLECMMnnnnnnnnnn login:
The first string in the prompt is the default host name, which consists of the prefix ORACLECMM followed by the CMM ILOM MAC address. The MAC address for each CMM and SP is unique.
32 SPARC T4-1B Server Module Installation Guide • May 2012
5. Log into ILOM on the CMM by typing your user name and password.
The factory default ILOM root password is changeme, but might have been changed in your environment.
You are now logged in to the CMM ILOM web interface.
After you have successfully logged in, the CMM ILOM displays its default command prompt:
->
6. Navigate to the server module:
-> cd /CH/BLn/SP/cli
Replace n with an integer that identifies the target server module (the slot for which the server module is installed).
7. Start the server module’s Oracle ILOM CLI:
-> start Are you sure you want to start /CH/BL0/SP/cli (y/n)? y start: Connecting to /CH/BL0/SP/cli using Single Sign On
Note – The CMM ILOM logs into the server module ILOM using the user name in
the user target under /CH/BLn/SP/cli (where n is the slot where the server module is installed).
8. If prompted for a password, enter the default password changeme.
9. At the Oracle ILOM prompt, type:
-> start /SYS Are you sure you want to start /SYS (y/n)? y
The server module initializes.
Powering On the Server Module for the First Time 33
10. Switch communication to the server module host.
When the ILOM prompt appears, type:
-> start /HOST/console Are you sure you want to start /HOST/console (y/n)? y Serial console started. To stop, type #.
The server module might take several minutes to complete POST. If a boot device installed with Oracle Solaris OS is accessible locally, the server module boots. Otherwise, the server module uses the boot net command to seek a boot device on the network.
You are now connected to the server module host.
11. The server module hardware installation is now complete.
You can now configure the Oracle Solaris OS to meet your needs. See
“Configuring the Oracle Solaris OS” on page 37.

Related Information

“Plan Communication With the Server Module During Installation” on page 15
Method 3 – Power On the Host
Through the Front Panel (SP CLI)
You can access the server module SP directly by connecting a dongle cable to the UCP on the front of the server module.
Caution – Dongle cables are intended for setup, testing, or service purposes and
should be removed when not in use. These cables have not been evaluated for electromagnetic compatibility compliance and are not to be used during normal operation. See “Dongle Cables” on page 17.
1. Configure the terminal device or terminal emulation software with these settings:
8N1 (eight data bits, no parity, one stop bit)
9600 baud (the default, but can be set to any standard rate up to 57600)
Disable hardware flow control (CTS/RTS)
34 SPARC T4-1B Server Module Installation Guide • May 2012
2. Connect the dongle cable to the UCP connector on the front panel of the server module.
If possible, use a three-connector UCP-3 dongle cable rather than a four-connector UCP-4. See “Dongle Cables” on page 17 for details.
3. Connect a terminal or terminal emulator to a dongle cable.
For a UCP-3 dongle cable, use the RJ-45 connector.
For a UCP-4 dongle cable, use the DB-9 serial connector (TTYA). If you need to
make an RJ-45 connection to a UCP-4, do so through a DB-9-to-RJ-45 adapter attached to the DB-9 connector.
The Oracle ILOM login prompt is displayed on the terminal or terminal emulator.
4. Type the user name and password when prompted.
The default user is root. The default password is changeme.
You are now logged into Oracle ILOM on the server module SP.
5. At the server module ILOM prompt, type:
-> start /SYS Are you sure you want to start /SYS (y/n)? y Starting /SYS. . .
The server module initializes.
6. Switch communication to the server module host.
When the Oracle ILOM prompt appears, type:
-> start /HOST/console Are you sure you want to start /HOST/console (y/n)? y Serial console started. To stop, type #.
The server module might take several minutes to complete POST. If a boot device installed with Oracle Solaris OS is accessible locally, the server module boots. Otherwise, the server module uses the boot net command to seek a boot device on the network.
You are now connected to the server module host.
7. The server module hardware installation is now complete.
You can now configure the Oracle Solaris OS to meet your needs. See
“Configuring the Oracle Solaris OS” on page 37.

Related Information

“Plan Communication With the Server Module During Installation” on page 15
Powering On the Server Module for the First Time 35
“Dongle Cables” on page 17
36 SPARC T4-1B Server Module Installation Guide • May 2012

Configuring the Oracle Solaris OS

After you install the server module in the modular system, you can power on the server for the first time and begin configuration.
Description Links
Configure the preinstalled Oracle Solaris OS. “Configure the OS” on page 37
“Oracle Solaris Configuration Parameters” on page 38
“Assign a Static IP Address to the SP” on page 40
Install your own version of the Oracle Solaris OS.
Related Information
“Installation Task Overview” on page 1
“Install Oracle Solaris Software From the Network” on page 38
“Oracle Solaris Configuration Parameters” on page 38
“Assign a Static IP Address to the SP” on page 40

Configure the OS

This procedure assumes that you are using the Oracle Solaris OS software that was preinstalled on the drive in slot 0 of the server module. If you are installing the Oracle Solaris OS another way, complete the Oracle Solaris OS installation then resume this procedure.
Respond to configuration questions in the Oracle Solaris installation process.
See the configuration choices you planned, based on “Oracle Solaris Configuration
Parameters” on page 38.
37

Related Information

“Install Oracle Solaris Software From the Network” on page 38
“Oracle Solaris Configuration Parameters” on page 38
“Assign a Static IP Address to the SP” on page 40
Install Oracle Solaris Software From
the Network
If you choose to use Oracle Solaris OS software other than the preinstalled Oracle Solaris OS, you can install the operating system from the network.
Refer to the Solaris Installation Guide: Network-Based Installations for the version of
Oracle Solaris OS that you plan to use.
You can obtain this guide in the Oracle Solaris OS documentation collections that are under the Systems Software category at:
http://http:www.oracle.com/technetwork/indexes/documentation/# sys_sw
This guide includes information about using a JumpStart server.

Related Information

“Configure the OS” on page 37
“Oracle Solaris Configuration Parameters” on page 38
“Assign a Static IP Address to the SP” on page 40

Oracle Solaris Configuration Parameters

You are prompted to provide these parameters when configuring the Oracle Solaris OS on the server module.
Parameter Description
Language Select a number from the displayed language list.
Locale Select a number from the displayed locale list.
38 SPARC T4-1B Server Module Installation Guide • May 2012
Terminal Type Select a terminal type that corresponds with your terminal device.
Network? Select Yes.
Multiple Network Interfaces
Select the network interfaces that you plan to configure. If you are not sure, select the first interface in the list.
DHCP? Select Yes or No according to your network environment.
Host Name Enter the host name for the server.
IP Address Enter the IP address for this Ethernet interface.
Subnet? Select Yes or No according to your network environment.
Subnet Netmask (If subnet was Yes) Enter the netmask for the subnet for your network
environment.
IPv6? Specify whether or not to use IPv6. If you are not sure, select No to configure the
Ethernet interface for IPv4.
Security Policy Select either standard UNIX security (No) or Kerberos Security (Yes). If you are not
sure, select No.
Confirm Review the onscreen information and change it if needed. Otherwise, continue.
Name Service Select the name service according to your network environment.
Note – If you select a name service other than None, you will be prompted for additional name service configuration information.
NFSv4 Domain Name Select the type of domain name configuration according to your environment. If
you are not sure, select Use the NFSv4 domain.
Time Zone (Continent) Select your continent.
Time Zone (Country or
Select your country or region.
Region)
Time Zone Select the time zone.
Date and Time Accept the default date and time or change the values.
root Password Enter the root password twice. This password is for the superuser account for the
Oracle Solaris OS on this server. This password is not the SP password.
Related Information
“Configure the OS” on page 37
“Install Oracle Solaris Software From the Network” on page 38
“Assign a Static IP Address to the SP” on page 40
Configuring the Oracle Solaris OS 39

Assign a Static IP Address to the SP

By default, the server module is configured to obtain an IP address from DHCP services in your network. If the network your server module is connected to does not support DHCP for IP addressing, perform this procedure.
To configure the server module to support DHCP, refer to the Oracle ILOM documentation.
1. Set the SP to accept a static IP address.
-> set /SP/network pendingipdiscovery=static Set 'pendingipdiscovery' to 'static'
2. Set the IP address for the SP.
-> set /SP/network pendingipaddress=service-processor-IPaddr Set 'pendingipaddress' to 'service-processor-IPaddr'
3. Set the IP address for the SP gateway.
-> set /SP/network pendingipgateway=gateway-IPaddr Set 'pendingipgateway' to 'gateway-IPaddr'
4. Set the netmask for the SP.
-> set /SP/network pendingipnetmask=255.255.255.0 Set 'pendingipnetmask' to '255.255.255.0'
This example uses 255.255.255.0 to set the netmask. Your network environment subnet might require a different netmask. Use a netmask number most appropriate to your environment.
5. Verify that the pending parameters are set correctly.
-> show /SP/network /SP/network Targets: Properties: commitpending = (Cannot show property) dhcp_server_ip = xxx.xxx.xxx.xxx ipaddress = xxx.xxx.xxx.xxx ipdiscovery = dhcp ipgateway = xxx.xxx.xxx.xxx
40 SPARC T4-1B Server Module Installation Guide • May 2012
ipnetmask = 255.255.255.0 macaddress = 00:21:28:C1:6E:C5 managementport = /SYS/MB/SP/NETMGMT outofbandmacaddress = 00:21:28:C1:6E:C5 pendingipaddress = service-processor-IPaddr pendingipdiscovery = static pendingipgateway = gateway-IPaddr pendingipnetmask = 255.255.255.0 pendingmanagementport = /SYS/MB/SP/NETMGMT sidebandmacaddress = 00:21:28:C1:6E:C4 state = enabled
6. Commit the changes to the SP network parameters.
-> set /SP/network commitpending=true Set 'commitpending' to 'true'
Note – You can type the show /SP/network command again to verify that the
parameters have been updated.
7. Set the static IP address when you configure the Oracle Solaris OS.
See “Configure the OS” on page 37.

Related Information

“Configure the OS” on page 37
“Install Oracle Solaris Software From the Network” on page 38
“Oracle Solaris Configuration Parameters” on page 38
Configuring the Oracle Solaris OS 41
42 SPARC T4-1B Server Module Installation Guide • May 2012

Glossary

A
ANSI SIS American National Standards Institute Status Indicator Standard.
ASF Alert standard format (Netra products only).
ASR Automatic system recovery.
AWG American wire gauge.
B
blade Generic term for server modules and storage modules. See server module and
storage module.
blade server Server module. See server module.
BMC Baseboard management controller.
BOB Memory buffer on board.
C
chassis For servers, refers to the server enclosure. For server modules, refers to the
modular system enclosure.
CMA Cable management arm.
43
CMM Chassis monitoring module. The CMM is the service processor in the
modular system. Oracle ILOM runs on the CMM, providing lights out management of the components in the modular system chassis. See Modular
system and Oracle ILOM.
CMM Oracle ILOM Oracle ILOM that runs on the CMM. See Oracle ILOM.
D
DHCP Dynamic Host Configuration Protocol.
disk module or
disk blade
DTE Data terminal equipment.
E
EIA Electronics Industries Alliance.
ESD Electrostatic discharge.
F
FEM Fabric expansion module. FEMs enable server modules to use the 10GbE
FRU Field-replaceable unit.
Interchangeable terms for storage module. See storage module.
connections provided by certain NEMs. See NEM.
H
HBA Host bus adapter.
host The part of the server or server module with the CPU and other hardware
that runs the Oracle Solaris OS and other applications. The term host is used to distinguish the primary computer from the SP. See SP.
44 SPARC T4-1B Server Module Installation Guide • May 2012
I
ID PROM Chip that contains system information for the server or server module.
IP Internet Protocol.
K
KVM Keyboard, video, mouse. Refers to using a switch to enable sharing of one
keyboard, one display, and one mouse with more than one computer.
L
LwA Sound power level.
M
MAC Machine access code.
MAC address Media access controller address.
Modular system The rackmountable chassis that holds server modules, storage modules,
NEMs, and PCI EMs. The modular system provides Oracle ILOM through its CMM.
MSGID Message identifier.
N
name space Top-level Oracle ILOM CMM target.
NEBS Network Equipment-Building System (Netra products only).
Glossary 45
NEM Network express module. NEMs provide 10/100/1000 Mbps Ethernet,
10GbE Ethernet ports, and SAS connectivity to storage modules.
NET MGT Network management port. An Ethernet port on the server SP, the server
module SP, and the CMM.
NIC Network interface card or controller.
NMI Nonmaskable interrupt.
O
OBP OpenBoot PROM.
Oracle ILOM Oracle Integrated Lights Out Manager. Oracle ILOM firmware is preinstalled
on a variety of Oracle systems. Oracle ILOM enables you to remotely manage your Oracle servers regardless of the state of the host system.
Oracle Solaris OS Oracle Solaris operating system.
P
PCI Peripheral component interconnect.
PCI EM PCIe ExpressModule. Modular components that are based on the PCI
Express industry-standard form factor and offer I/O features such as Gigabit Ethernet and Fibre Channel.
POST Power-on self-test.
PROM Programmable read-only memory.
PSH Predictive self healing.
Q
QSFP Quad small form-factor pluggable.
46 SPARC T4-1B Server Module Installation Guide • May 2012
R
REM RAID expansion module. Sometimes referred to as an HBA See HBA.
Supports the creation of RAID volumes on drives.
S
SAS Serial attached SCSI.
SCC System configuration chip.
SER MGT Serial management port. A serial port on the server SP, the server module SP,
and the CMM.
server module Modular component that provides the main compute resources (CPU and
memory) in a modular system. Server modules might also have onboard storage and connectors that hold REMs and FEMs.
SP Service processor. In the server or server module, the SP is a card with its
own OS. The SP processes Oracle ILOM commands providing lights out management control of the host. See host.
SSD Solid-state drive.
SSH Secure shell.
storage module Modular component that provides computing storage to the server modules.
T
TIA Telecommunications Industry Association (Netra products only).
Tma Maximum ambient temperature.
U
UCP Universal connector port.
Glossary 47
UI User interface.
UL Underwriters Laboratory Inc.
US. NEC United States National Electrical Code.
UTC Coordinated Universal Time.
UUID Universal unique identifier.
W
WWN World wide name. A unique number that identifies a SAS target.
48 SPARC T4-1B Server Module Installation Guide • May 2012

Index

A
altitude specifications, 8 antistatic mat and wrist strap (Installation), 14 architecture, processor, 2
C
cable, dongle, 17 chassis
inserting the server module, 23
preparation, 21 CLI for installation, 29 CMM NET MGT port, 15 CMM SER MGT port, 15
using for installation, 31 communicating with the server module, 15 components, optional, 23 configuration settings for Oracle Solaris OS, 38 configuring the IP address, 40 configuring the Oracle Solaris OS, 37 connecting to the server
CMM NET MGT port (CLI), 29
CMM NET MGT port (Web Interface), 28
CMM SER MGT port (CLI), 31
UCP connector, 34 connection methods, 15 connector covers, 23 cooling, 2 customer information sheet, 12
D
data connector, 4 depth, 7 DHCP used to obtain IP address, 40 dimensions, 7 DIMM types, 2
documentation, related, v dongle cable, 15, 34 dongle cables, 15, 17, 34
E
ejector arms, 23 electrical specifications, 8 environmental specifications, 8 ESD precautions, 13 Ethernet ports, 2
F
features, server module, 2 FEMs, 2 filler panels, 23 front panel components, 4
G
graphics, onboard, 2
H
handling precautions, 13 height, 7 humidity specifications, 8
I
ILOM root password, default, 28, 29, 31, 34 installation
chassis preparation, 21 planning, 7, 11 task overview, 1
tools required, 14 installing the server module, 21 inventory of shipping kit, 12 IP address of CMM, 28
49
IP address, configuring, 40
root password, default, 28
K
KVMS, 2
L
LEDs
front panel, 4 upon installation, 23
M
MAC address, 12 memory, 2 modular system chassis preparation, 21
O
optional components, 23 Oracle Solaris
configuration settings, 38
configuring, 37 Oracle Solaris OS configuration settings, 38 OS
installing from the network, 38
Oracle Solaris configuration settings, 38 overview, installation task, 1
P
PCIe EMs, 2 physical specifications, 7 planning the installation, 7, 11 power button, 4 power connector, 4 power specifications, 8 powering on the server module, 27 precautions
ESD, 13
handling, 13 processor architecture, 2
S
serial cable pin assignments, 31 serial port connection, 15, 17 serial redirection, 28 server module
configuring the OS, 37 features, 2 inserting into chassis, 23 installing, 21 installing the OS from the network, 38 powering on, 27 starting, 31
understanding, 1 set command, 40 shipping kit inventory, 12 show command, 40 specifications
electrical, 8
environmental, 8
physical, 7
ssh command, 29 start command, 29, 31
starting the server module, 31 static IP address, 40 system firmware, 2
T
task overview, installation, 1 temperature specifications, 8 tools required for installation, 14
U
UCP cables, 17 UCP connector, 2, 4, 34 understanding the server module, 1 USB connection, 17
R
rear panel components, 4 related documentation, v remote console, 28 REMs, 2 reset button, 4
50 SPARC T4-1B Server Module Installation Guide • May 2012
V
VGA connection, 17 voltage specifications, 8
W
web interface, 28
weight, 7
width, 7
Index 51
52 SPARC T4-1B Server Module Installation Guide • May 2012
Loading...